Wacker Neuson BS60-2i Manuel utilisateur

Operator’s Manual

Rammer

BS 60-2i

BS 70-2i

Notice d’Emploi

Pilonneuse

5000184129 06 0411

5000184129

EN / FR

Copyright

notice

All rights, including copying and distribution rights, are reserved.

This publication may be photocopied by the original purchaser of the machine. Any

other type of reproduction is prohibited without express written permission from

Wacker Neuson Production Americas LLC.

Any type of reproduction or distribution not authorized by Wacker Neuson Production

Americas LLC represents an infringement of valid copyrights. Violators will be

prosecuted.

Trademarks

All trademarks referenced in this manual are the property of their respective owners.

Manufacturer

Wacker Neuson Production Americas LLC

N92W15000 Anthony Avenue

Menomonee Falls, WI 53051 U.S.A.

Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957

www.wackerneuson.com

Original

instructions

This Operator’s Manual presents the original instructions. The original language of this

Operator’s Manual is American English.

5000184105 06 0411

BS 60-2i / BS 70-2i Foreword

wc_tx000914gb.fm 3

Foreword

SAVE THESE INSTRUCTIONS—This manual contains important instructions for

the machine models below. These instructions have been written expressly by

Wacker Neuson Production Americas LLC and must be followed during installation,

operation, and maintenance of the machines.

Machine

documentation

 From this point forward in this documentation, Wacker Neuson Production

Americas LLC will be referred to as Wacker Neuson.

 Keep a copy of the Operator’s Manual with the machine at all times.

 Use the separate Parts Book supplied with the machine to order replacement

parts.

 Refer to the separate Repair Manual for detailed instructions on servicing and

repairing the machine.

 If you are missing any of these documents, please contact Wacker Neuson to

order a replacement or visit www.wackerneuson.com.

 When ordering parts or requesting service information, be prepared to provide

the machine model number, item number, revision number, and serial number.

Expectations

for

information in

this manual

 This manual provides information and procedures to safely operate and main-

tain the above Wacker Neuson model(s). For your own safety and to reduce the

risk of injury, carefully read, understand, and observe all instructions described

in this manual.

 Wacker Neuson expressly reserves the right to make technical modifications,

even without notice, which improve the performance or safety standards of its

machines.

 The information contained in this manual is based on machines manufactured

up until the time of publication. Wacker Neuson reserves the right to change

any portion of this information without notice.

Machine Item number

BS 60-2i 0009339 Rev 124, 200 and higher

0009393 Rev 123, 200 and higher

0009419 Rev 125

0009419 Rev 127, 200 and higher

0009420 Rev 126, 200 and higher

0620613 Rev 100, 200 and higher

0620614 Rev 100, 200 and higher

BS 70-2i 0009341 Rev 123, 200 and higheri

0009401 Rev 123, 200 and higher

0009426 Rev 125, 200 and higher

0009428 Rev 126, 200 and higher

Foreword BS 60-2i / BS 70-2i

4 wc_tx000914gb.fm

CALIFORNIA

Proposition

65 Warning

Engine exhaust, some of its constituents, and certain vehicle components, contain

or emit chemicals known to the State of California to cause cancer and birth

defects or other reproductive harm.

Laws

pertaining to

spark

arresters

NOTICE: State Health Safety Codes and Public Resources Codes specify that in

certain locations spark arresters be used on internal combustion engines that use

hydrocarbon fuels. A spark arrester is a device designed to prevent accidental dis-

charge of sparks or flames from the engine exhaust. Spark arresters are qualified

and rated by the United States Forest Service for this purpose. In order to comply

with local laws regarding spark arresters, consult the engine distributor or the local

Health and Safety Administrator.

Manufacturer’s

approval

This manual contains references to approved parts, attachments, and modifica-

tions. The following definitions apply:

 Approved parts or attachments are those either manufactured or provided by

Wacker Neuson.

 Approved modifications are those performed by an authorized Wacker Neu-

son service center according to written instructions published by Wacker Neu-

son.

 Unapproved parts, attachments, and modifications are those that do not

meet the approved criteria.

Unapproved parts, attachments, or modifications may have the following conse-

quences:

 Serious injury hazards to the operator and persons in the work area

 Permanent damage to the machine which will not be covered under warranty

Contact your Wacker Neuson dealer immediately if you have questions about

approved or unapproved parts, attachments, or modifications.

William Lahner Paul Sina

Vice President of Engineering Manager, Product Engineering

WACKER NEUSON PRODUCTION AMERICAS LLC

2011-CE-BS60-2--BS70-2_en.fm

EC DECLARATION OF CONFORMITY

WACKER NEUSON PRODUCTION AMERICAS LLC, N92W15000 ANTHONY AVENUE,

MENOMONEE FALLS, WISCONSIN USA

hereby certifies that the construction equipment specified hereunder:

has been sound tested per Directive 2000/14/EC:

AUTHORIZED PERSON FOR TECHNICAL DOCUMENTS Axel Häret

WACKER NEUSON SE

Preußenstraße 41

80809 München

1. Category:

Vibratory Rammer

2. Machine function:

This machine is intended to be used for compacting cohesive, mixed, and granular soils in confined areas.

3. Type / Model

Rammer BS 60-2, BS 60-2i, BS 70-2, BS 70-2i

4. Item number of equipment:

0009417, 0009421, 0009419, 0009420, 0009424, 0009425, 0009427, 0009426, 0009428

5. Net installed power:

BS 60-2, BS 60-2i 1,8 kW

BS 70-2, BS 70-2i 2,0 kW

Conformity Assessment

Procedure

Name and address of notified body Measured sound power level Guaranteed sound power level

ANNEX VIII Lloyds Register Quality

Assurance Limited (Notified

Body No 0088)

71 Fenchurch Street

London EC3M 4BS

United Kingdom

106 dB(A) 108dB(A)

6. This machinery fulfills the relevant provisions of Machinery Directive 2006/42/EC and is also produced in accordance with

these standards:

2000/14/EC

2004/26/EC

2004/108/EC

EN 500-1

EN 500-4

The original language of this EC Declaration of Conformity is American English.

03.01.11

Date

EC Declaration of Conformity

wc_bo5000184105_06TOC.fm 7

Table of ContentsBS 60-2i / BS 70-2i

Foreword 3

EC Declaration of Conformity 5

1 Safety Information 9

1.1 Signal Words Used in this Manual ....................................................... 9

1.2 Machine Description and Intended Use ............................................. 10

1.3 Safety Guidelines for Operating the Machine ..................................... 11

1.4 Operator Safety while Using Internal Combustion Engines ............... 13

1.5 Service Safety .................................................................................... 14

2 Labels 16

2.1 Label Locations .................................................................................. 16

2.2 Label Meanings .................................................................................. 17

3 Lifting and Transporting 21

4 Operation 23

4.1 Preparing the Machine for First Use ................................................... 23

4.2 Recommended Fuel ........................................................................... 23

4.3 Position of the Operator ..................................................................... 25

4.4 Before Starting ................................................................................... 26

4.5 Starting ............................................................................................... 26

4.6 Stopping ............................................................................................. 27

4.7 Emergency Shutdown Procedure ....................................................... 27

5 Maintenance 28

5.1 Maintaining the Emission Control System .......................................... 28

5.2 Periodic Maintenance Schedule ......................................................... 29

5.3 Servicing the Air Cleaner .................................................................... 30

5.4 Checking and Changing the Ramming System Oil ............................ 32

8 wc_bo5000184105_06TOC.fm

Table of Contents BS 60-2i / BS 70-2i

5.5 Shoe Hardware ...................................................................................34

5.6 Adjusting the idle speed ......................................................................35

5.7 Long-Term Storage .............................................................................36

6 Basic Troubleshooting 38

7 Technical Data 39

7.1 Rammer ...............................................................................................39

7.2 Sound Measurements .........................................................................40

7.3 Vibration Measurements .....................................................................40

7.4 Dimensions ..........................................................................................41

8 Emission Control Systems Information and Warranty 43

8.1 Emission Control System Background Information .............................43

8.2 Limited Defect Warranty for Wacker Neuson Emission Control

Systems ...............................................................................................44

BS 60-2i / BS 70-2i Safety Information

wc_si000496gb.fm 9

1 Safety Information

1.1 Signal Words Used in this Manual

This manual contains DANGER, WARNING, CAUTION, NOTICE, and

NOTE signal words which must be followed to reduce the possibility

of personal injury, damage to the equipment, or improper service.

NOTICE: Used without the safety alert symbol, NOTICE indicates a

situation which, if not avoided, could result in property damage.

Note: A Note contains additional information important to a procedure.

This is the safety alert symbol. It is used to alert you to potential personal hazards.

f Obey all safety messages that follow this symbol.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death

or serious injury.

f To avoid death or serious injury from this type of hazard, obey all safety

messages that follow this signal word.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

f To avoid possible death or serious injury from this type of hazard, obey all safety

messages that follow this signal word.

CAUTION

CAUTION indicates a hazardous situation which, if not avoided, could result in

minor or moderate injury.

f To avoid possible minor or moderate injury from this type of hazard, obey all

safety messages that follow this signal word.

Safety Information BS 60-2i / BS 70-2i

10 wc_si000496gb.fm

1.2 Machine Description and Intended Use

This machine is a vibratory rammer. The Wacker Neuson Rammer

consists of a gasoline or diesel engine, a clutch, a fuel tank, a spring-

loaded ramming system, a ramming shoe, and a handle. The engine

transmits power through the ramming system and ramming shoe,

generating percussive impact force to compact soil. The operator

guides and controls the machine from behind using the handle.

This machine is intended to be used for compacting cohesive, mixed,

and granular soils in confined areas.

This machine has been designed and built strictly for the intended use

described above. Using the machine for any other purpose could

permanently damage the machine or seriously injure the operator or

other persons in the area. Machine damage caused by misuse is not

covered under warranty.

The following are some examples of misuse:

• Using the machine as a ladder, support, or work surface

• Using the machine to carry or transport passengers or equipment

• Using the machine as a hammer or for other demolition work

• Attaching the machine to any other machine

• Operating the machine outside of factory specifications

• Operating machine in a manner inconsistent with all warnings

found on the machine and in the Operator’s Manual

This machine has been designed and built in accordance with the

latest global safety standards. It has been carefully engineered to

eliminate hazards as far as practicable and to increase operator

safety through protective guards and labeling. However, some risks

may remain even after protective measures have been taken. They

are called residual risks. On this machine, they may include exposure

to:

• Heat, noise, exhaust, and carbon monoxide from the engine

• Fire hazards from improper refueling techniques

• Fuel and its fumes

• Personal injury from improper lifting techniques or operating

techniques

To protect yourself and others, make sure you thoroughly read and

understand the safety information presented in this manual before

operating the machine.

BS 60-2i / BS 70-2i Safety Information

wc_si000496gb.fm 11

1.3 Safety Guidelines for Operating the Machine

Familiarity and proper training are required for the safe operation of the

machine. Machines operated improperly or by untrained personnel

can be hazardous. Read the operating instructions contained in this

manual and the engine manual, and familiarize yourself with the

location and proper use of all controls. Inexperienced operators should

receive instruction from someone familiar with the machine before

being allowed to operate it.

Operator qualifications

Only trained personnel are permitted to start, operate, and shut down

the machine. They also must meet the following qualifications:

• have received instruction on how to properly use the machine

• are familiar with required safety devices

The machine must not be accessed or operated by:

•children

• people impaired by alcohol or drugs

Personal Protective Equipment (PPE)

Wear the following Personal Protective Equipment (PPE) while

operating this machine:

• Close-fitting work clothes that do not hinder movement

• Safety glasses with side shields

• Hearing protection

• Safety-toed footwear

1.3.1 Never operate this machine in applications for which it is not intended.

1.3.2 Do not allow anyone to operate this equipment without proper training.

People operating this equipment must be familiar with the risks and

hazards associated with it.

1.3.3 Do not touch the engine or muffler while the engine is on or

immediately after it has been turned off. These areas get hot and may

cause burns.

1.3.4 Do not operate the machine with unapproved accessories or

attachments.

1.3.5 Never leave the machine running unattended.

1.3.6 Never tamper with or disable the function of operating controls.

1.3.7 Never use the choke to stop the engine.

1.3.8 Never operate the machine in areas where explosions may occur.

1.3.9 Read, understand, and follow procedures in the Operator’s Manual

before attempting to operate the machine.

WARNING

Safety Information BS 60-2i / BS 70-2i

12 wc_si000496gb.fm

1.3.10 Make sure that all other persons are at a safe distance from the

machine. Stop the machine if people step into the working area of the

machine.

1.3.11 Be sure operator is familiar with proper safety precautions and

operation techniques before using machine.

1.3.12 Always wear protective clothing appropriate to the job site when

operating the machine.

1.3.13 Wear hearing protection when operating equipment.

1.3.14 Always keep hands, feet, and loose clothing away from moving parts

of the machine.

1.3.15 Always use common sense and caution when operating the machine.

1.3.16 Always be sure the rammer will not tip over, roll, slide, or fall when not

being operated.

1.3.17 Always turn the engine OFF when the rammer is not being operated.

1.3.18 Always guide the rammer in such a way that the operator is not

squeezed between the rammer and solid objects. Special care is

required when working on uneven ground or when compacting coarse

material. Make sure to stand firmly when operating the machine under

such conditions.

1.3.19 When working near the edges of breaks, pits, slopes, trenches and

platforms, always operate the rammer in such a way that there is no

danger of it tipping over or falling in.

1.3.20 Store the machine properly when it is not being used. The machine

should be stored in a clean, dry location out of the reach of children.

1.3.21 Close fuel valve on engines equipped with one when machine is not

being operated.

1.3.22 Always operate machine with all safety devices and guards in place

and in working order. Do not modify or defeat safety devices. Do not

operate machine if any safety devices or guards are missing or

inoperative.

1.3.23 Do not transport the machine while it is running.

1.3.24 Do not tip the machine for cleaning or for any other reason.

BS 60-2i / BS 70-2i Safety Information

wc_si000496gb.fm 13

1.4 Operator Safety while Using Internal Combustion Engines

Operating safety

When running the engine:

• Keep the area around exhaust pipe free of flammable materials.

• Check the fuel lines and the fuel tank for leaks and cracks before

starting the engine. Do not run the machine if fuel leaks are present

or the fuel lines are loose.

When running the engine:

• Do not smoke while operating the machine.

• Do not run the engine near sparks or open flames.

• Do not touch the engine or muffler while the engine is running or

immediately after it has been turned off.

• Do not operate a machine when its fuel cap is loose or missing.

• Do not start the engine if fuel has spilled or a fuel odor is present.

Move the machine away from the spill and wipe the machine dry

before starting.

Refueling safety

When refueling the engine:

• Clean up any spilled fuel immediately.

• Refill the fuel tank in a well-ventilated area.

• Replace the fuel tank cap after refueling.

• Do not smoke.

• Do not refuel a hot or running engine.

• Do not refuel the engine near sparks or open flames.

• Do not refuel if the machine is positioned in a truck fitted with a

plastic bed liner. Static electricity can ignite the fuel or fuel vapors.

WARNING

Internal combustion engines present special hazards during operation and fueling. Failure to

follow the warnings and safety standards could result in severe injury or death.

f Read and follow the warning instructions in the engine owner’s manual and the

safety guidelines below.

DANGER

Exhaust gas from the engine contains carbon monoxide, a deadly poison.

Exposure to carbon monoxide can kill you in minutes.

f NEVER operate the machine inside an enclosed area, such as a tunnel, unless

adequate ventilation is provided through such items as exhaust fans or hoses.

Safety Information BS 60-2i / BS 70-2i

14 wc_si000496gb.fm

1.5 Service Safety

A poorly maintained machine can become a safety hazard! In order

for the machine to operate safely and properly over a long period of

time, periodic maintenance and occasional repairs are necessary.

Personal Protective Equipment (PPE)

Wear the following Personal Protective Equipment (PPE) while

servicing or maintaining this machine:

• Close-fitting work clothes that do not hinder movement

• Safety glasses with side shields

• Hearing protection

• Safety-toed footwear

In addition, before servicing or maintaining the machine:

• Tie back long hair.

• Remove all jewelry (including rings).

Service training

Before servicing or maintaining the machine:

• Read and understand the instructions contained in all manuals

delivered with the machine.

• Familiarize yourself with the location and proper use of all

controls and safety devices.

• Only trained personnel shall troubleshoot or repair problems

occurring with the machine.

• Contact Wacker Neuson for additional training if necessary.

When servicing or maintaining this machine:

• Do not allow improperly trained people to service or maintain the

machine. Personnel servicing or maintaining the machine must

be familiar with the associated potential risks and hazards.

1.5.1 Do not attempt to clean or service the machine while it is running.

Rotating parts can cause severe injury.

1.5.2 DO NOT operate the machine without an air cleaner.

1.5.3 DO NOT remove air cleaner cover, paper element, or precleaner while

engine is running.

1.5.4 DO NOT alter engine speeds. Run the engine only at speeds specified

in the Technical Data Section.

1.5.5 Do not crank a flooded engine with the spark plug removed on

gasoline-powered engines. Fuel trapped in the cylinder will squirt out

the spark plug opening.

WARNING

BS 60-2i / BS 70-2i Safety Information

wc_si000496gb.fm 15

1.5.6 Do not test for spark on gasoline-powered engines if the engine is

flooded or the smell of gasoline is present. A stray spark could ignite

the fumes.

1.5.7 Do not use gasoline or other types of fuels or flammable solvents to

clean parts, especially in enclosed areas. Fumes from fuels and

solvents can become explosive.

1.5.8 ALWAYS replace the safety devices and guards after repairs and

maintenance.

1.5.9 Keep the area around the muffler free of debris such as leaves, paper,

cartons, etc. A hot muffler could ignite the debris and start a fire.

1.5.10 ALWAYS do periodic maintenance as recommended in the Operator’s

Manual.

1.5.11 ALWAYS clean debris from engine cooling fins.

1.5.12 When replacement parts are required for this machine, use only

Wacker Neuson replacement parts or those parts equivalent to the

original in all types of specifications, such as physical dimensions,

type, strength, and material.

1.5.13 Disconnect the spark plug on machines equipped with gasoline

engines, before servicing, to avoid accidental start-up.

1.5.14 Keep the machine clean and labels legible. Replace all missing and

hard-to-read labels. Labels provide important operating instructions

and warn of dangers and hazards.

1.5.15 ALWAYS follow instructions when disconnecting fuel lines. Failure to

do so may result in fuel squirting from fuel system.

Labels BS 60-2i / BS 70-2i

16 wc_si000497gb.fm

2 Labels

2.1 Label Locations

BS 60-2i / BS 70-2i Labels

wc_si000497gb.fm 17

2.2 Label Meanings

A

To start the machine:

1. Move the throttle to the IDLE position.

2. Push the purge bulb 10 times.

3. Close the choke.

4. Pull the starter rope until engine starts.

5. Move the throttle to the FAST position.

To stop the machine:

1. Move the throttle past the SLOW position.

Warning! To reduce the risk of hearing loss, always wear

hearing protection when operating this machine.

Read the Operator’s Manual.

Danger!

Asphyxiation hazard.

 Engines emit carbon monoxide.

 Do not run the machine indoors or in an enclosed

area unless adequate ventilation, through such items

as exhaust fans or hoses, is provided.

 No sparks, flames, or burning objects near the

machine.

 Stop the engine before refueling.

This label is molded into the cover. If the label becomes

illegible, the cover must be replaced. Refer to the Parts

Book for ordering information.

Labels BS 60-2i / BS 70-2i

18 wc_si000497gb.fm

D

Warning!

Springs are compressed. Release cover slowly to avoid

spring ejection.

See the Repair Manual for proper disassembly

instructions.

F

For optimal control, performance, and minimal hand/arm

vibration, grasp handle as shown.

Read the Operator’s Manual.

G

Guaranteed sound power level in dB(A).

H

The air intake system is equipped with a filter indicator,

which indicates when a filter change is required.

Replace main paper filter element when yellow plunger

of the indicator appears in or near the red line.

BS 60-2i / BS 70-2i Labels

wc_si000497gb.fm 19

I

A nameplate listing the model number, item number,

revision number, and serial number is attached to each

unit. Please record the information found on this name-

plate so it will be available should the nameplate

become lost or damaged. When ordering parts or

requesting service information, you will always be asked

to specify the model number, item number, revision

number, and serial number of the unit.

L

Emission control information

This engine is certified to operate on regular unleaded

gasoline and two cycle oil located in separate tanks

Displacement 80cc

Exhaust emissions control system: OC

Engine family: BW1XS.0805CA

This engine meets U.S. EPA exhaust regulations for

2011

This equipment meets U.S. EPA evaporative regulations

using certified components

Emission compliance period: 300 hours (heavy use)

This engine is certified to operate on regular unleaded

gasoline mixed with two cycle oil at 50:1–100:1 ratio.

Read the Operator’s Manual.

M

Gasoline

Labels BS 60-2i / BS 70-2i

20 wc_si000497gb.fm

N

Turtle = Idle/slow engine speed

Rabbit = Full/fast engine speed

This label is molded into the cover. If the label becomes

illegible, the cover must be replaced. Refer to the Parts

Book for ordering information.

O

1. Move the throttle to the IDLE position.

2. Close the choke.

P

Engine oil tank.

--

This machine may be covered by one or more patents.

La page charge ...

Wacker Neuson BS60-2i Manuel utilisateur

Ce manuel convient également à

Wacker Neuson BS60-2i Manuel utilisateur

dans d''autres langues

Documents connexes