Generac PowerPact Series G0065190 Manuel utilisateur

Owner’s Manual

For

Automatic Transfer Switch

PowerPact™ Home Standby Generator

MODEL NUMBER: _________________________

SERIAL NUMBER: _________________________

DATE PURCHASED:________________________

WWW.GENERAC.COM

1-888-GENERAC

(1-888-436-3722)

Para español , visita:

http://www.generac.com/service-support/product-support-lookup

Pour le français, visiter : http://www.generac.com/service-support/product-support-lookup

SAVE THIS MANUAL FOR FUTURE REFERENCE

ii Automatic Transfer Switch Owner’s Manual

(000005)

WARNING

California Proposition 65. This product contains or

emits chemicals known to the state of California to

cause cancer, birth defects, and other reproductive

harm.

(000004)

WARNING

California Proposition 65. Engine exhaust and some

of its constituents are known to the state of California

to cause cancer, birth defects, and other reproductive

harm.

Table of Contents

PowerPact™ Automatic Transfer Switch Owner’s Manual iii

Section 1: Introduction and Safety

Introduction ..........................................................1

Safety Rules .........................................................1

Safety Symbols and Meanings ...........................2

General Hazards ..................................................3

Section 2: General Information

Unpacking ............................................................5

Equipment Description .......................................5

Transfer Switch Features ....................................5

Specifications ......................................................5

Transfer Switch Data Decal ................................5

Transfer Switch Enclosure .................................6

Safe Use of Transfer Switch ...............................6

Section 3: Installation

Introduction ..........................................................7

Mounting ...............................................................7

Connecting Power Source and Load Lines .......7

2-Pole Mechanism ...............................................8

Connecting Start Circuit Wires ...........................8

Circuit Breaker Wiring .........................................9

Section 4: Operation

Functional Tests and Adjustments ..................11

Manual Operation ..............................................11

Close to Normal Source Side ....................................11

Close to Emergency Source Side .............................11

Return to Normal Source Side ..................................12

Voltage Checks ..................................................12

Utility Voltage Checks ...............................................12

Generator Voltage Checks ........................................12

Generator Tests Under Load ............................13

Checking Automatic Operation ........................13

Shutting Generator Down While Under Load ..13

Installation Summary ........................................13

Section 5: Drawings and Diagrams

Installation Diagram .......................................... 15

(Drawing 0K8843-A) ..................................................15

Interconnection Drawing .................................. 16

(Drawing 0K8844-B) ..................................................16

Table of Contents

iv PowerPact™ Automatic Transfer Switch Owner’s Manual

This page intentionally left blank.

Introduction and Safety

PowerPact™ Automatic Transfer Switch Owner’s Manual 1

Section 1: Introduction and Safety

Introduction

Thank you for purchasing a Generac Power Systems Inc.

product. This unit has been designed to provide high-

performance, efficient operation, and years of use when

maintained properly.

Read this manual thoroughly and understand all of the

instructions, cautions, and warnings before using this

equipment. If any section of the manual is not

understood, contact your nearest authorized dealer, or

contact Generac Customer Service at 1-888-436-3722

(1-888-GENERAC), or www.generac.com with any

questions or concerns.

The owner is responsible for proper maintenance and

safe use of the equipment. Before operating or servicing

this transfer switch:

• Study all warnings in this manual and on the

product carefully.

• Become familiar with this manual and the unit

before use.

• Refer to the Installation section of the manual for

instructions on final assembly procedures. Follow

the instructions completely.

Save these instructions for future reference. ALWAYS

supply this manual to any individual that will use this

machine.

THE INFORMATION CONTAINED HEREIN WAS

BASED ON MACHINES IN PRODUCTION AT THE

TIME OF PUBLICATION. GENERAC RESERVES THE

RIGHT TO MODIFY THIS MANUAL AT ANY TIME.

Safety Rules

The manufacturer cannot anticipate every possible

circumstance that might involve a hazard. The warnings

in this manual, and on tags and decals affixed to the unit

are, therefore, not all inclusive. If using a procedure, work

method or operating technique that the manufacturer

does not specifically recommend, verify that it is safe for

others. Also make sure the procedure, work method or

operating technique utilized does not render the

equipment unsafe.

Throughout this publication, and on tags and decals

affixed to the transfer switch, DANGER, WARNING,

CAUTION and NOTE blocks are used to alert personnel

to special instructions about a particular operation that

may be hazardous if performed incorrectly or carelessly.

Observe them carefully. Their definitions are as follows:

NOTE: Notes contain additional information important to

a procedure and will be found within the regular text of

this manual.

These safety warnings cannot eliminate the hazards that

they indicate. Common sense and strict compliance with

the special instructions while performing the action or

service are essential to preventing accidents.

(000001)

DANGER

Indicates a hazardous situation which, if not avoided,

will result in death or serious injury.

(000002)

WARNING

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury.

(000003)

CAUTION

Indicates a hazardous situation which, if not avoided,

could result in minor or moderate injury.

Introduction and Safety

2 PowerPact™ Automatic Transfer Switch Owner’s Manual

Safety Symbols and Meanings

(000129)

DANGER

Electrocution. High voltage is present at

transfer switch and terminals. Contact with live

terminals will result in death or serious injury.

(000104)

DANGER

Electrocution. Water contact with a power

source, if not avoided, will result in death

or serious injury.

(000145)

DANGER

Electrocution. In the event of electrical accident,

immediately shut power OFF. Use non-conductive

implements to free victim from live conductor. Apply

first aid and get medical help. Failure to do so will

result in death or serious injury.

(000131a)

DANGER

Electrical backfeed. Use only approved switchgear to

isolate generator when electrical utility is the primary

power source. Failure to do so will result in death,

serious injury, and equipment damage.

(000195)

DANGER

Electrocution, equipment and property damage.

Handle transfer switches carefully when installing.

Never install a damaged transfer switch. Doing so

could result in death or serious injury, equipment

and property damage.

(000123)

DANGER

Electrocution. Turn utility supply OFF before

working on utility connections of the transfer

switch. Failure to do so will result in

death or serious injury.

(000157)

DANGER

Electrocution. Do not disable or modify the

connection box door safety switch. Doing so

will result in death or serious injury.

Automatic start-up. Disconnect utility power and

render unit inoperable before working on unit.

Failure to do so will result in death or serious injury.

(000191)

DANGER

(000119)

Equipment malfunction. Installing a dirty or damaged

transfer switch will cause equipment malfunction and

will result in death or serious injury.

DANGER

(000100a)

WARNING

Consult Manual. Read and understand manual

completely before using product. Failure to

completely understand manual and product

could result in death or serious injury.

(000155)

WARNING

Only a trained and licensed electrician should perform

wiring and connections to unit. Failure to follow proper

installation requirements could result in death, serious

injury, and damage to equipment or property.

(000120)

CAUTION

Equipment damage. Verify all conductors are

tightened to the factory specified torque value.

Failure to do so could result in damage

to the switch base.

(000121)

CAUTION

Equipment damage. Perform functional tests in the

exact order they are presented in the manual.

Failure to do so could result in equipment damage.

(000134a)

CAUTION

Equipment damage. Exceeding rated voltage

and current will damage the auxiliary contacts.

Verify that voltage and current are within specification

before energizing this equipment.

Introduction and Safety

PowerPact™ Automatic Transfer Switch Owner’s Manual 3

General Hazards

• Any AC generator that is used for backup power if

a NORMAL (UTILITY) power source failure occurs

must be isolated from the NORMAL (UTILITY)

power source by means of an approved transfer

switch. Failure to properly isolate the NORMAL

and STANDBY power sources from each other

may result in injury or death to electric utility

workers, due to backfeed of electrical energy.

• Extremely high power and dangerous voltages are

present inside an installed transfer switch. Any

contact with high voltage terminals, contacts or

wires can result in LETHAL electric shock, while

arc flash can cause blindness and severe burns.

DO NOT WORK ON THE TRANSFER SWITCH

UNTIL YOU HAVE CONFIRMED THAT ALL

POWER SUPPLIES TO THE SWITCH ARE

TURNED OFF.

• Competent, qualified personnel should install,

operate and service this equipment. Adhere strictly

to local, state and national electrical and building

codes. When using this equipment, comply with

regulations the National Electrical Code (NEC),

CSA Standard; C22.1 Canadian Electric Code and

Occupational Safety and Health Administration

(OSHA) have established.

• Never handle any kind of electrical device while

standing in water, while barefoot, or while hands or

feet are wet. DANGEROUS ELECTRICAL SHOCK

MAY RESULT.

• Because jewelry conducts electricity, wearing it

may cause dangerous electrical shock. Remove all

jewelry (such as rings, watches, bracelets, etc.)

before working on this equipment.

• If working on this equipment while standing on

metal or concrete, place insulative mats over a dry

wood platform. Work on this equipment only while

standing on such insulative mats.

• Never work on this equipment while physically or

mentally fatigued.

• Keep the transfer switch enclosure door closed

and bolted at all times. Only qualified personnel

should be permitted access to the switch interior.

• When an automatic transfer switch is installed for a

standby generator set, the generator engine may

crank and start at any time without warning. To

avoid possible injury that might be caused by such

sudden start-ups, the system’s automatic start

circuit must be disabled before working on or

around the generator or transfer switch. Then

place a “DO NOT OPERATE” tag on the transfer

switch and on the generator.

• Any voltage measurements should be performed

with a meter that meets UL3111 safety standards,

and meets or exceeds overvoltage class CAT III.

Introduction and Safety

4 PowerPact™ Automatic Transfer Switch Owner’s Manual

This page intentionally left blank.

General Information

PowerPact™ Automatic Transfer Switch Owner’s Manual 5

Section 2: General Information

Unpacking

Carefully unpack the transfer switch. Inspect closely for

any damage that might have occurred during shipment.

The purchaser must file with the carrier any claims for

loss or damage incurred while in transit.

Check that all packing material is completely removed

from the switch prior to installation.

Equipment Description

This automatic transfer switch is used for transferring

critical electrical load from a utility (normal) power source

to a generator (standby) power source. Such a transfer of

electrical loads occurs automatically when the utility

power source has failed or is substantially reduced and

the generator source voltage and frequency have

reached an acceptable level. The transfer switch

prevents electrical feedback between two different power

sources (such as the utility and generator sources) and,

for that reason, codes require it in all standby electric

system installations.

The transfer switch consists of a transfer mechanism, a

control relay, a terminal strip and fuse holder for

connection of sensing wires.

This switch is suitable for control of motors, electric

discharge lamps, tungsten filament and electric heating

equipment and the tungsten load does not exceed 30%

of the switch rating.

This UL listed transfer switch is for use in optional

standby systems only (NEC article 702).

A 50A rated switch is suitable for use on circuits capable

of delivering not more than 10,000 RMS symmetrical

amperes, 250 VAC maximum, when protected by a 50A

maximum circuit breaker (Siemens types QP or BQ) or

50A maximum circuit breaker (Square D Q2,

Westinghouse CA-CAH, General Electric TQ2 and

Siemens QJ2).

Transfer Switch Features

• Utilizes standard Siemens components

• UL listed to U.S.A. and Canadian safety standards

• Single panels are compatible with single-phase

generators rated up to 50 Amps/12 kW

• Flush or Surface Mount NEMA 1 enclosure

This switch is listed for use with the following one inch

breakers:

• Siemens*

• Murray*

• Eaton

• Square D

*Including GFCI, AFCI and tandem breakers up to 50

amps.

NOTE: For branch circuits over 50 amps, only listed

Siemens or Murray circuit breakers shall be used.

Specifications

Transfer Switch Data Decal

A data decal is permanently affixed to the transfer switch

enclosure. Use this transfer switch only with the specific

limits shown on the data decal and on other decals and

labels that may be affixed to the switch. This will prevent

damage to equipment and property.

When requesting information or ordering parts for this

equipment, make sure to include all information from the

data decal.

For future reference, record the Model and Serial

numbers in the space provided on the front cover of this

manual.

Enclosure NEMA Type 1, Surface or Flush

Mount, general purpose, painted

metal, for interior use only

Transfer Switch Generator Lugs (E1, E2)

Transfer Switch Wire

Size

Load Lugs (T1, T2)

Ground Lug #12–20

Neutral Bar #4–14 AWG

Ground Fault or Arc

Fault Circuit Breaker

QPF or QAF Siemens

Withstand Rating Main

Bus (Amps)

10,000

Meets NEC Wire

Bending Space

Yes

UL Listed and CSA Yes

Weight:

Without Whips

With Whips

20 lbs (9.1 kg)

39 (17.7 kg)

Operating Temperature –20°F to 140°F (-29°C to 60°C)

General Information

6 PowerPact™ Automatic Transfer Switch Owner’s Manual

Figure 2-1. Panelboard With Operator

Transfer Switch Enclosure

The standard switch enclosure is a National Electrical

Manufacturer’s Association (NEMA) UL Type 1.

Safe Use of Transfer Switch

Before installing, operating or servicing this equipment,

read Introduction and Safety carefully. Comply strictly

with all information presented in Introduction and

Safety to prevent accidents and/or damage to the

equipment. The manufacturer recommends that a copy

of Introduction and Safety be posted near the transfer

switch. Also, be sure to read all instructions and

information found on tags, labels and decals affixed to

the equipment.

Two publications that outline the safe use of transfer

switches are the following:

• NFPA 70; National Electrical Code

• NFPA 70E: Standard for Electrical Safety in the

Workplace

• UL 1008: Standard for Safety—Automatic Transfer

Switches

• UL 97: Standard for Safety—Panelboard

NOTE: It is essential to use the latest version of any

standard to verify correct and current information.

001482

(000100a)

WARNING

Consult Manual. Read and understand manual

completely before using product. Failure to

completely understand manual and product

could result in death or serious injury.

Installation

PowerPact™ Automatic Transfer Switch Owner’s Manual 7

Section 3: Installation

Introduction

This equipment has been wired and tested at the factory.

Installing the switch includes the following procedures:

• Mounting the enclosure.

• Connecting power source and load leads.

• Connecting the generator start and sensing circuit.

• Testing functions.

Mounting

Mounting dimensions for the NEMA Type 1 Transfer

Switch enclosure are in this manual. Enclosures are

typically wall-mounted. See Drawings and Diagrams.

Protect the switch against impact at all times, and against

construction grit and metal chips.

1. Locate automatic transfer switch with built-in

emergency load center in close proximity to the

main distribution panel. The transfer switch can be

located to the left or right of the main distribution

panel. One (1) foot (0.3 m) is the suggested

distance.

NOTE: The transfer switch may be located a different

distance from the main panel depending on available

mounting area. Using the two (2) foot (0.61 m) conduit

connected straight across to the main panel is another

option. Always adhere to local electrical codes during

installation.

2. Hold transfer switch against the mounting surface.

Level the transfer switch and mark the mounting

holes.

3. Drill the appropriate size pilot holes.

4. Mount transfer switch with built-in load center to

mounting surface with appropriate fasteners.

NOTE: See Figure 3-1. Transfer switch MUST be

mounted vertically as shown.

Figure 3-1. Mount Transfer Switch

5. Switch service main circuit breaker to the OFF

(OPEN) position prior to removal of cover or

removal of any wiring of the main electrical

distribution panel. The wires connected to the

service main circuit breaker remain LIVE or HOT.

Avoid contact with these wires and the service

main circuit breaker connection lugs.

NOTE: This switch may be equipped with 2 foot (0.67 m)

or 30 foot (9.1 m) whips. If not provided, size conductors

and conduits according to NEC codes.

Connecting Power Source and Load Lines

Installation and interconnection diagrams are provided in

this manual.

NOTE: All installations must comply with national, state

and local codes. It is the responsibility of the installer to

perform an installation that will pass the final electrical

inspection.

(000195)

DANGER

Electrocution, equipment and property damage.

Handle transfer switches carefully when installing.

Never install a damaged transfer switch. Doing so

could result in death or serious injury, equipment

and property damage.

(000119)

Equipment malfunction. Installing a dirty or damaged

transfer switch will cause equipment malfunction and

will result in death or serious injury.

DANGER

001483

(000213)

DANGER

Electrocution. Only authorized personnel should

access transfer switch interior. Transfer switch doors

should be kept closed and locked. Failure to do so

will result in death or serious injury.

Electrocution. Turn utility and emergency

power supplies to OFF before connecting

power source and load lines. Failure to do so

will result in death or serious injury.

(000116)

DANGER

(000155)

WARNING

Only a trained and licensed electrician should perform

wiring and connections to unit. Failure to follow proper

installation requirements could result in death, serious

injury, and damage to equipment or property.

Installation

8 PowerPact™ Automatic Transfer Switch Owner’s Manual

2-Pole Mechanism

See Figure 3-2. These switches are used with a single-

phase system when the single-phase NEUTRAL line is to

be connected to a Neutral Lug and is not to be switched.

Figure 3-2. Typical 2-Pole Transfer Mechanism

Solderless, screw-type terminal lugs are standard.

Conductor sizes must be adequate to handle the

maximum current to which they will be subjected, based

on the 167° F (75°C) column of tables, charts, etc. used

to size conductors. The installation must comply fully with

all applicable codes, standards and regulations.

Before connecting wiring cables to terminals, remove any

surface oxides from the cable ends with a wire brush. All

power cables should enter the switch next to transfer

mechanism terminals.

NOTE: If aluminum conductors are used, apply corrosion

inhibitor to conductors. After tightening terminal lugs,

carefully wipe away any excess corrosion inhibitor.

Tighten terminal lugs to the torque values as noted on the

decal located on the inside of the door. After tightening

terminal lugs, carefully wipe away any excess corrosion

inhibitor.

Connect power source and load conductors to clearly

marked terminal lugs on transfer mechanism as follows:

1. Connect utility (normal) power source cables to

utility service disconnect circuit breaker.

2. Connect the generator (standby) source power

cables to transfer switch terminals E1, E2., and E3

3. Connect customer LOAD leads to switch terminals

T1 and T2.

Conductors must be properly supported, of approved

insulative qualities, protected by approved conduit, and

of the correct wire gauge size in accordance with

applicable codes.

Be sure to maintain proper electrical clearance between

live metal parts and grounded metal. Allow at least one-

half inch (13 mm) for 100-400 amp circuits.

Connecting Start Circuit Wires

Control system interconnections (Electrical Data section)

consist of UTILITY 1 (N1), UTILITY 2 (N2) and LOAD

(T1), and leads 23 and 194. Recommended wire gauge

sizes for this wiring depends on the length of the wire, as

recommended in the following chart:

Exception: Conductors of AC and DC circuits, rated

1000 volts nominal or less, shall be permitted to occupy

the same equipment, cable, or conduit. All conductors

shall have an insulation rating equal to at least the

maximum circuit voltage applied to any conductor within

the equipment, cable, or conduit. See NEC 300.3(C)(1).

A. Utility Lugs (N1 & N2)

B. Generator Lugs (E1 & E2)

C. Load Lugs (T1 & T2)

Switch Rating Wire Range Conductor

Tightening Torque

50A 1/0–14 AWG 50 in.lbs. (5.65 Nm)

001488

A

C

B

(000120)

CAUTION

Equipment damage. Verify all conductors are

tightened to the factory specified torque value.

Failure to do so could result in damage

to the switch base.

Maximum Wire Length Recommended Wire Size

1–115 ft (1–35 m) No. 18 AWG

116–185 ft (36–56 m) No. 16 AWG

186–295 ft (57–89 m) No. 14 AWG

296–460 ft (90–140 m) No. 12 AWG

Installation

PowerPact™ Automatic Transfer Switch Owner’s Manual 9

Circuit Breaker Wiring

NOTE: Balance must be maintained when moving circuit

locations from main electrical distribution panel to

emergency load center. Circuit breaker positions

alternate buss bars vertically. Circuits sharing a neutral

wire should either be moved together to adjacent

positions in emergency load center or not moved. If

unsure of the proper procedure or if the installation differs

from that described in this guide, consult a licensed

professional at this time.

1. Remove the main electrical distribution panel

cover.

2. Remove appropriate size knockout from the right

side of the main panel. (If provided, a two foot (0.67

m) flexible conduit is pre-wired from the transfer

switch with built-in load center).

3. Remove threaded lock nut from conduit coupling.

Feed all wires through knockout into main panel.

Slip lock nut over wires and tighten securely onto

conduit coupling.

NOTE: Circuits to be moved must be protected by same

size breaker. For example, a 15 amp 120 volt circuit in

emergency load center will replace a 15 amp 120 volt

circuit in main electrical distribution panel.

4. In the main panel, remove the black (hot) wire from

the circuit breaker that protects a circuit to be

powered in the event of a power failure. Wire nut

the black wire to the matching circuit lead wire from

the emergency circuit breaker in the load center in

the transfer switch. (All circuit wires are color

coded and labeled for easy identification). UL listed

wire locknuts are included in installation kit.

5. Trace each black (hot) wire connected and wire nut

the white (neutral) wire from the same Romex

cable (circuit) to the matching circuit number on the

white (neutral) wire from the emergency load

center. Repeat for each circuit.

6. Repeat this process with the remaining circuits to

be powered by the generator.

NOTE: Both grounded and ungrounded conductors must

be moved to the emergency panel and connected to the

new wiring from the emergency panel using supplied wire

nuts.

7. Install the 50 amp double pole breaker; 7 kW

(purchased or supplied separately), into main

electrical distribution panel. This circuit breaker

must be compatible with the main electrical

distribution panel. It may be necessary to

reposition remaining circuit breakers or remove

circuit breakers that have been disconnected to

accommodate the insertion of the 50 amp double

pole circuit breaker.

8. Connect white wire to the main distribution panel

neutral bar.

9. Connect solid green wire to main electrical panel

ground bar.

10. Connect the black and red wires to the 50 amp

double pole circuit breaker.

11. Reinstall the main distribution panel cover.

Installation

10 PowerPact™ Automatic Transfer Switch Owner’s Manual

This page intentionally left blank.

Operation

PowerPact™ Automatic Transfer Switch Owner’s Manual 11

Section 4: Operation

Functional Tests and Adjustments

Following transfer switch installation and interconnection,

inspect the entire installation carefully. A competent,

qualified electrician should inspect it. The installation must

comply strictly with all applicable codes, standards, and

regulations. When absolutely certain the installation is

proper and correct, complete a functional test of the system.

IMPORTANT: Before proceeding with functional tests,

read and make sure all instructions and information in

this section is understood. Also read the information and

instructions of labels and decals affixed to the switch.

Note any options or accessories that might be installed

and review their operation.

Manual Operation

See Figure 4-1. A manual transfer handle (D) is shipped

with the transfer switch. Manual operation must be

checked BEFORE the transfer switch is operated

electrically. To check manual operation, proceed as

follows:

1. Verify the generator is in the OFF mode.

2. Turn OFF or OPEN both UTLITY and

EMERGENCY power supplies to the transfer

switch, with whatever means provided (such as the

main line circuit breakers).

3. Note position of transfer mechanism main contacts

by observing the movable contact carrier arm.

•

Manual operation handle towards the top of switch

mechanism—LOAD terminals (T1, T2) are

connected to STANDBY terminals (E1, E2

).

• Manual operation handle towards the bottom of

switch mechanism—LOAD terminals (T1, T2) are

connected to UTILITY terminals (N1, N2).

Close to Normal Source Side

See Figure 4-1. Before proceeding, verify the position of

the switch by observing the position of the manual

transfer handle (D).

Figure 4-1. Actuating Transfer Switch

If the handle is down, the contacts are closed in the

normal position. No further action is required. If the

handle is UP, proceed.

With the handle inserted into the actuating shaft, move

handle DOWN. Be sure to hold on to the handle as it will

move quickly after the center of travel.

Close to Emergency Source Side

See Figure 4-1. Before proceeding, verify the position of

the switch by observing the position of the manual

transfer handle (D).

If the handle is UP, the contacts are closed in the

EMERGENCY (Standby) position. No further action is

required. If the handle is down, proceed.

With the handle inserted into the actuating shaft, move

the handle UP. Be sure to hold on to the handle as it will

move quickly after the center of travel.

(000121)

CAUTION

Equipment damage. Perform functional tests in the

exact order they are presented in the manual.

Failure to do so could result in equipment damage.

(000132)

DANGER

Electrocution. Do not manually transfer under load.

Disconnect transfer switch from all power sources

prior to manual transfer. Failure to do so will result

in death or serious injury, and equipment damage.

(000122)

CAUTION

Equipment damage. Do not use excessive force

while manually operating the transfer switch.

Doing so could result in equipment damage.

A. Load connected to standby power source

B. Load connected to utility power source

C. Transfer switch operating lever

D. Manual transfer handle

001484

A

B

C

D

Operation

12 PowerPact™ Automatic Transfer Switch Owner’s Manual

Return to Normal Source Side

Manually actuate switch to return manual operating

handle to the DOWN position.

Voltage Checks

Utility Voltage Checks

1. Turn ON the UTILITY power supply to the transfer

switch with whatever means provided (such as the

UTILITY main line circuit breaker).

2. With an accurate AC voltmeter, check for correct

voltage. Measure across ATS terminal lugs N1 and

N2; N1 to NEUTRAL and N2 to NEUTRAL.

3. When certain that UTILITY supply voltage is

correct and compatible with transfer switch ratings,

turn OFF the UTILITY supply to the transfer switch.

Generator Voltage Checks

1. On the generator panel, select the MANUAL mode

of operation. The generator should crank and start.

2. Let the generator stabilize and warm up at no-load

for at least five minutes.

3. Set the generator main circuit breaker (CB1) to ON

or CLOSED.

4. With an accurate AC voltmeter and frequency

meter, check the no-load, voltage and frequency.

Measure across ATS terminal lugs E1 to E2; E1 to

NEUTRAL and E2 to NEUTRAL.

5. When certain that generator supply voltage is

correct and compatible with transfer switch ratings,

turn OFF the generator supply to the transfer

switch.

6. Set the generator main circuit breaker (CB1) to

OFF or OPEN.

7. On the generator panel, select the OFF mode to

shut down the generator.

NOTE: Do NOT proceed until generator AC output

voltage and frequency are correct and within stated

limits. If the no-load voltage is correct but no-load

frequency is incorrect, the engine governed speed may

require adjustment. If no-load frequency is correct but

voltage is not, the voltage regulator may require

adjustment.

(000129)

DANGER

Electrocution. High voltage is present at

transfer switch and terminals. Contact with live

terminals will result in death or serious injury.

(000123)

DANGER

Electrocution. Turn utility supply OFF before

working on utility connections of the transfer

switch. Failure to do so will result in

death or serious injury.

Frequency 60–62 Hz

Terminals E1 to E2 240–246 VAC

Terminals E1 to NEUTRAL 120–123 VAC

Terminals E2 to NEUTRAL 120–123 VAC

(000129)

DANGER

Electrocution. High voltage is present at

transfer switch and terminals. Contact with live

terminals will result in death or serious injury.

Operation

PowerPact™ Automatic Transfer Switch Owner’s Manual 13

Generator Tests Under Load

1. Turn OFF the utility power supply to the transfer

switch with whatever means provided (such as the

utility main line circuit breaker).

2. Set the generator main circuit breaker to OFF or

OPEN.

3. Manually actuate the transfer switch main contacts

to the emergency (Standby) position. See Manual

Operation. To start the generator, select the

MANUAL mode of operation. When engine starts,

let it stabilize for a few minutes.

4. Set the generator main circuit breaker to ON or

CLOSED. The generator now powers all LOAD

circuits. Check generator operation under load as

follows:

• Turn on electrical loads to the full rated wattage/

amperage capacity of the generator. DO NOT

OVERLOAD.

• With maximum rated load applied, check voltage

and frequency across transfer switch terminals E1

and E2. Voltage should be greater than 230 volts

(240 VAC system); frequency should be greater

than 59 Hz.

• Let the generator run under rated load for at least

30 minutes. With unit running, listen for unusual

noises, vibration, overheating, etc., that might

indicate a problem.

5. When checkout under load is complete, set main

circuit breaker of the generator to the OFF or

OPEN position.

6. Let the generator run at no-load for several

minutes. Then, shut down by selecting the OFF

mode.

7. Move the main switch contacts back to UTILITY.

NOTE: See Manual Operation. Handle and operating

lever of transfer switch should be in down position.

8. Turn on the utility power supply to transfer switch,

using whatever means provided (such as a utility

main line circuit breaker). The utility power source

now powers the loads.

9. The system is now set for fully automatic operation.

Checking Automatic Operation

To check the system for proper automatic operation,

proceed as follows:

1. Verify generator is in OFF mode.

2. Install front cover of the transfer switch.

3. Turn the utility power supply to the transfer switch

ON, using the utility main line circuit breaker.

4. Set the generator main circuit breaker to ON.

5. On the generator panel, select AUTO. The system

is now ready for automatic operation.

6. Turn utility power supply to the transfer switch OFF.

With the generator ready for automatic operation, the

engine should crank and start when the utility source

power is turned OFF after a ten second delay (factory

default setting). After starting, the transfer switch should

connect load circuits to the standby side after a five (5)

second delay. Let the system operate through its entire

automatic sequence of operation.

Shutting Generator Down While Under Load

Important! To turn the generator off during utility outages

to perform maintenance, or conserve fuel, follow these

important steps:

To turn the generator OFF (while running in AUTO and

online):

1. Turn the main utility disconnect OFF.

2. Turn the main line circuit breaker (MLCB) on the

generator to OFF (OPEN).

3. Let the generator run at no-load several minutes.

4. Turn the generator OFF.

To turn the generator back ON:

1. Put the generator back into AUTO and allow to

start and warm-up for a few minutes.

2. Set the MLCB on the generator to ON.

The system will now be operating in its automatic mode.

The main utility disconnect can be turned ON (CLOSED).

NOTE: To shut the unit off, this complete process must

be repeated.

Installation Summary

1. Verify the installation has been properly performed

as outlined by the manufacturer and that it meets

all applicable laws and codes.

2. Verify proper operation of the system as outlined in

the appropriate Installation and Owner’s Manuals.

3. Educate the end user on the proper operation,

maintenance and service call procedures.

Operation

14 PowerPact™ Automatic Transfer Switch Owner’s Manual

This page intentionally left blank.

Drawings and Diagrams

PowerPact™ Automatic Transfer Switch Owner’s Manual 15

Section 5 Drawings and Diagrams

Installation Diagram

(Drawing 0K8843-A)

PP>@

PP>@

5PP>5@

5PP>5@

.12&.28768,7$%/()25

&21'8,76,=(

,))7:+,3127,1&/8'('

PP>@

PP>@

PP>@

PP>@

PP>@

PP>@

PP>@

PP>@

PP>@

PP>@

001485

Drawings and Diagrams

16 PowerPact™ Automatic Transfer Switch Owner’s Manual

\Interconnection Drawing

(Drawing 0K8844-B)

$25$

6(59,&(

+286(0$,1

&,5&8,7%5($.(5

$32/(

7

1

1





(

(

*1'

711

 

(

(

1

1

*(1(5$725&86720(5

&211(&7,21

&,5&8,775$16)(56:,7&+

&86720(56833/,('

-81&7,21%2;

001486

La page charge ...

Generac PowerPact Series G0065190 Manuel utilisateur

Generac PowerPact Series G0065190 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents