Airwell WKW 45 2T Installation and Maintenance Manual

Marque: Airwell

Modèle: WKW 45 2T

Catégorie: Climatiseurs split-system

Taper: Installation and Maintenance Manual

Ce manuel convient également à

English Français EspañolDeutsch Italiano

IOM KOG 02-N-8GB

Part number / Code / Teil Nummer / Codice / Código : 3990269GB

Supersedes / Annule et remplace / Annulliert und ersetzt /

Annulla e sostituisce / Anula y sustituye : IOM KOG 02-N-7GB

Installation and maintenance manual

Manuel d’installation et de maintenance

Installations- und Wartungshandbuch

Manuale di installazione e di manutenzione

Manual de instalación y de mantenimiento

CHILLED OR HEATED WATER CASSETTE

CASSETTE EAU GLACEE OU EAU CHAUDE

KALTWASSER ODER GEHEIZTESWASSER -KASSETTE

CASSETTA ACQUA GHIACCIATA O RISCALDATA

CASETE AGUA HELADA O CALENTADA

IOM KOG 02-N-8

Part number / Code / Teil Nummer / Codice / Código : 3990269

Supersedes / Annule et remplace / Annulliert und ersetzt /

Annulla e sostituisce / Anula y sustituye : IOM KOG 02-N-7

K 30 OG 2T

K 45 OG 2T

K 45 OG 4T

ECF 30 OG 2T

ECF 45 OG 2T

ECF 45 OG 4T

SCW 30 2T

SCW 45 2T

SCW 45 4T

WKW 30 2T

WKW 45 2T

WKW 45 4T

INSTALLATION INSTRUCTION

NOTICE D’INSTALLATION

INSTALLATIONSHANDBUCH

ISTRUZIONI INSTALLAZIONE

INSTRUCCIONES DE INSTALACIÓN

Chilled Water Cassette

Contents

1 SAFETY PRECAUTIONS ............................................................................................ 3

2 DESCRIPTION .......................................................................................................... 4

2.1 PACKAGE CONTENTS ..................................................................................................................................... 4

2.2 2 PIPES CASSETTE DIMENSIONS .................................................................................................................... 4

2.3 WEIGHTS........................................................................................................................................................ 4

2.4 4 PIPES CASSETTE DIMENSIONS .................................................................................................................... 5

2.5 WEIGHTS........................................................................................................................................................ 5

3 GENERAL ................................................................................................................. 6

3.1 ELECTRICAL SPECIFICATION ..........................................................................................................................6

3.2 OPERATING LIMITS .........................................................................................................................................6

AIR TEMPERATURE LIMITS ......................................................................................................................................................................6

WATER TEMPERATURE LIMITS ................................................................................................................................................................. 6

3.3 INSPECTION AND HANDLING ....................................................................................................................... 7

4 INSTALLATION......................................................................................................... 8

4.1 INSTALLATION LOCATION ............................................................................................................................. 8

4.2 CEILING MOUNTING ..................................................................................................................................... 8

4.3 CASSETTE FITTING ......................................................................................................................................... 9

4.4 CASSETTE INSTALLATION ............................................................................................................................... 9

5 CONNECTIONS ..................................................................................................... 10

5.1 CONDENSATE EVACUATION ....................................................................................................................... 10

5.2 HYDRAULIC CONNECTIONS ........................................................................................................................ 10

6 ELECTRICAL CONNECTION ................................................................................... 11

6.1 ELECTRICAL CONNECTION ............................................... ........................................................................... 11

6.2 CHANGE OVER SENSOR CONNECTION (MODELS 2T) ................................................................................11

THERMOSTAT INSTALLATION ............................................................................................................................................................... 11

WATER TEMPERATURE PROBE INSTALLATION .......................................................................................................................................11

6.3 ELECTRIC HEATING ...................................................................................................................................... 12

6.4 FAULT WARNING REPEATER ......................................................................................................................... 12

6.5 VENTILATION SPEEDS .................................................................................................................................. 12

6.6 WIRING DIAGRAM ....................................................................................................................................... 12

7 ELECTRICITY .......................................................................................................... 13

7.1 THERMOSTAT LOCATION ............................................................................................................................. 13

7.2 CONTROL .................................................................................................................................................... 13

INFRA RED VERSION - INFRA RED REMOTE CONTROL ......................................................................................................................... 13

USE ........................................................................................................................................................................................................................13

ROOM THERMOSTAT TRM-VP AND TRM-FA .........................................................................................................................................15

SWITCHES ..............................................................................................................................................................................................................15

DIMENSIONS .........................................................................................................................................................................................................15

ELECTRICAL CONNECTIONS ..................................................................................................................................................................................15

WALL MOUNTING ..................................................................................................................................................................................................15

TECHNICAL CHARACTERISTICS ...............................................................................................................................................................................15

FINAL OPERATIONS ................................................................................................................................................................................................16

TAE20 ROOM THERMOSTAT ...............................................................................................................................................................17

FIELDS OF APPLICATION .........................................................................................................................................................................................17

DESCRIPTION .........................................................................................................................................................................................................17

ADJUSTMENT AND CONTROL ELEMENTS ...............................................................................................................................................................17

8 AIR DISTRIBUTION ................................................................................................ 18

8.1

AIR DISTRIBUTION MODULE FITTING .............................................................................................................................18

8.2 FILTER INSTALLATION .................................................................................................................................. 18

9 COMMISSIONING ................................................................................................. 19

9.1 CHECKS BEFORE COMMISSIONING ............................................................................................................. 19

9.2 GENERAL INSTALLATION ............................................................................................................................ 19

9.3 ELECTRICAL ELEMENTS ................................................................................................................................ 19

Chilled Water Cassette

THE MANUFACTURER’S WARRANTY WILL NOT APPLY IF THE INSTALLATION

RECOMMENDATIONS LISTED IN THIS MANUAL ARE NOT FOLLOWED.

WARNING !

The installation, commissioning and maintenance of these

units should be performed by qualified personnel having

a good knowledge of standards and local regulations,

as well as experience of this type of equipment.

WARNING !

Any wiring produced on site must comply with local

electrical regulations.

WARNING !

Ensure that the electrical supply corresponds to the

specification indicated on the unit’s maker’s plate before

proceeding with the connection in accordance with the

wiring diagram supplied.

WARNING !

The unit must be EARTHED to avoid any risks caused by

insulation defects.

WARNING !

No wiring must come in contact with the heat source or

the fan rotating parts.

NOTE: PLEASE REFER TO THE TECHNICAL MANUAL FOR THE LIMITATIONS OF USE AND TECHNICAL

CHARACTERISTICS.

ELECTRICAL POWER MUST BE SWITCHED OFF BEFORE

STARTING ANY WORK ON CONTROL BOXES

The aim of this manual is to provide cassette users with instructions for installation, commissioning, operation and

maintenance.

It does not contain the complete description of all the maintenance operations guaranteeing the unit’s long life and reliability.

Only the services of a qualified technician can guarantee the unit’s safe operation over a long service life.

safety preCautions

Take care !

The unit should be handled using lifting and handling

equipment appropriate to the unit’s size and weight.

Take care !

It is forbidden to start any work on the electrical

components without switching off the electrical supply

to the unit.

Take care !

It is forbidden to start any work on the electrical

components if water or high humidity is present on the

installation site.

Take care !

When the unit is being connected, ensure that no

impurities are introduced into the pipe work and the

water circuits.

Take care !

A device to disconnect all the power conductors with an

approved minimum opening distance must be included

in the mains power supply according to best installation

practices.

Take care !

The units may contain a small amount of oil incompatible

with plastic polyethylene piping (PER/HTA/PVC). The coil

should be rinsed out before use to avoid any problem.It is

the installer’s responsibility to contact their pipe supplier

and take into account the general instructions for the use

of plastic pipes (PER/HTA/PVC).

Chilled Water Cassette

2.1 PACKAGE CONTENTS

1 Cassette

2 Angle attachment fittings

1 Fastener bag: Angle brackets + screws

Rubber shock absorbing pads

Treated air distribution frame screws

Fascia clips

2.2 2 PIPES CASSETTE DIMENSIONS 2.3 WEIGHTS

DesCription

1 Documentation bag

1 Fascia assembly

1 Suspended ceiling

2 T bar (suspended ceiling)

3 Evaporator

4 Fan

5 Intake grille

6 Electrical connection

7 Condensate evacuation Ø 15

MODELS 30 2T 45 2T

WEIGHTS (kg) 49 55

Dimensions in mm

8 Water intake RC1"

9 Water outlet RC1"

10 Opening for ducted air distribution into the adjacent

room (ready to punch out)

11 Port for fresh air succion (ready to punch out)

12 Air vent

Chilled Water Cassette

2.4 4 PIPES CASSETTE DIMENSIONS

2.5 WEIGHTS

DesCription ContinueD

1 Suspended ceiling

2 T bar (suspended ceiling)

3 Evaporator

4 Fan

5 Intake grille

6 Electrical connection

7 Condensate evacuation Ø 15

8 Hot water outlet RC1/2"

8a Hot water intake RC1/2"

9 Cold water outlet RC1"

9a Cold water intake RC1"

10 Opening for ducted air distribution into the adjacent

room (ready to punch out)

11 Port for fresh air succion (ready to punch out)

12 Cold water air vent

MODELS 45 4T

WEIGHTS (kg) 55

Dimensions in mm

Chilled Water Cassette

3.1 ELECTRICAL SPECIFICATION

* Minimum cable diameter to be determined in accordance with installation conditions and local

standards.

** aM or C curve trip switch

1 thermostat for each cassette or installation with the 7ACEL1207 kit for a MAXIMUM of 4 Cassettes.

General

Models 30 2P 45 2P

with heating without heating with heating without heating

Nominal current A 19 7.4 0.9 8.8 0.96

Maximal current A 22.6 8.5 1.27 10.6 1.35

Fuse rating gG A 25 10 2 ** 16 2 **

Fuse rating ASE / VDE A 25 10 2 16 2

Power supply 230V 50Hz 3N ~ 400V - 50Hz 230V 50Hz 3N ~ 400V - 50Hz 230V 50Hz

Cable section mini* mm² 3G4 5G1.5 3G1.5 5G1.5 3G1.5

Electric heating capacity W 4300 4300 / 5400 /

Models 45 4P

Nominal current A 0.96

Maximal current A 1.35

Fuse rating aM ** A 2

Fuse rating ASE / VDE A 2

Power supply 230V 50Hz

Cable section mini* mm² 3G1.5

3.2 OPERATING LIMITS

Standard unit

Cooling Heating

Minimum ambient temperature (wb) 13 °C /

Minimum ambient temperature (db) 17 °C /

Maximum ambient temperature (wb) 22 °C 22 °C

Maximum ambient temperature (db) 32 °C 32 °C

Standard unit

Cooling Heating

2T / 4T 2T with heating

Minimum water inlet temperature 3 °C / /

Maximum water inlet temperature 18 °C 70 °C 35 °C

AIR TEMPERATURE LIMITS

Please consult us for operating conditions exceeding these temperatures.

WATER TEMPERATURE LIMITS

db: dry bulb wb: wet bulb

Chilled Water Cassette

3.3 INSPECTION AND HANDLING

In the event of shipping damage, write precise

details of the damage on the shipper’s delivery note

and send a registered letter with acknowledgement

of receipt to the shipper within 48 hours, clearly

stating the damage caused. Forward a copy of the

letter to the manufacturer or their representative.

N.B. Writing “subject to unpacking” on the delivery note is

not sufficient for the shipper’s insurance company.

IIt is recommended to place the cassette as near as possible

to the final installation site before unpacking.

Avoid placing heavy tools or weights on top of the packed

cassette.

On opening the carton, check that all the accessories

required for installation are present.

Keep the fascia grille in its packaging until it is to be finally

installed.

DO NOT LIFT THE CASSETTE BY THE

CONDENSATE EVACUATION TUBE

The sharp edges and surfaces of the coils can

cause injury. Avoid contact with them.

WARNING !

General ContinueD

Chilled Water Cassette

4.1 INSTALLATION LOCATION

Installing the cassette will be easier with the use of a fork

lift truck. Use the packing base by placing it between the

cassette and the truck forks.

It is recommended to install the cassette, as far as is possible,

in the centre of the room, in order to optimise treated air

distribution.

For the chosen location, check that the distribution grilles

can be removed and that there is sufficient space available

for access for maintenance and repairs.

When fitting the angle attachment fittings in the low position,

remove the insulating foam from around the mounting

nuts.

The possibility of fitting the angle attachment fittings

at different heights, leaves the installer the choice of

mounting them on the cassette in the high or low position.

Mounting them in the low position provides for more flexible

installation.

Do not tighten the nuts or lock nuts. This will be done only

after having set the cassette in its final horizontal position,

when are the connections have been completed.

4.2 CEILING MOUNTING

Mark the position of each support rod.

Refer to Chapter 2“Dimensions”

The cassettes must not be positioned above

electrical equipment in order to avoid exposure

to water leaks which may occur under extreme

conditions.

107

270

1220

510

installation

Fit the angle attachment fittings supplied with the cassette

onto the threaded rods (not supplied). Recommended Ø 6

mm maximum Ø 8 mm. Take care to distance them from

the suspended ceiling by 270 mm or 107 mm.

Take care !

Do not install the cassette in a room where gasses, acids or

inflammable products are stored, in order to avoid damage

to the aluminium and copper evaporators and the internal

plastic parts.

Do not install the cassette in a workshop or a kitchen. Oil

vapour attracted by the treated air could form deposits on

the cassette evaporators and modify their performance or

damage the cassette’s internal plastic parts.

Do not install the cassette in a laundry, or a room where

steam is produced.

It is recommended to insure a sufficient ventilation around

the cassette.

The cassette is designed to be built into a suspended

ceiling with panels dimensions of 60 x 60 cm, or multiples

thereof.

Chilled Water Cassette

4.4 CASSETTE INSTALLATION

Side openings are provided for installing separate ducts for

outside air intake and treated air distribution to an adjacent

room.

Use a punch to remove the condensation protection insulation

and the pre-punched panels from the openings.

TAKE CARE not to damage the heat exchanger coil

located behind the openings.

Plug the gaps between the ducts and the opening edge with

anti-condensation insulation.

Use material which can withstand a continuous operating

temperature of 60° C. The ducts can be of the flexible type

with a spring core or of corrugated aluminium, covered

inside with an insulating material (12 to 25 mm thick glass

fibre).

If it is intended to install ducting to an adjacent room, refer to § 4.4 for

removal of the pre-punched panel before installing the cassette.

4.3 CASSETTE FITTING

To make the assembly easier the electrical box can be

disassembled by removing 2 screws, and disconnect the

multipoints connectors (15 pts connector for the main

connection, 12 pts connector for the electric heating) and

small connector for the infra-red.

Fix the cassette, connect the multipoints connectors, place

the cassette into is final position and reset the electric box

with 2 screws

Fix the screws to fix the corner irons

In the event that the suspended ceiling is 300 mm from the

ceiling (minimum permitted height), it might be necessary

to temporarily remove some of the suspended ceiling T

supports.

Position the cassette on the suspended ceiling support

rods, and start by tightening the side mounting bolts, then

the threaded rods nuts and lock nuts, after having set the

cassette level, maintaining a gap of around 10 mm between

the metal chassis and the suspended ceiling.

Decompression grille

When the installation is finished, all the surfaces of the

non-insulated ducts must be covered with anti-condensation

insulation material (6 mm thick expanded polystyrene or

expanded neoprene). Fireproofing classification: M1)

IF THE ABOVE INSTRUCTIONS ARE NOT FOLLOWED,

CONDENSATE LEAKS MAY OCCUR.

Distributing air to an adjacent room requires one or two

of the corresponding ducts’ air distribution flaps to be

closed.

A decompression grille must be fitted in the partition between

the air conditioned room (where the cassette is installed)

and the adjacent room.

New air

intake

Treated air

distribution

WARNING !

installation ContinueD

Chilled Water Cassette

The condensate evacuation pipe must be heat insulated

to a thickness of 5 to 10 mm with insulating material such

as polyurethane, propylene or neoprene (Fireproofing

classification: M1) to prevent condensation.

If several cassettes are installed in the room, the evacuation

system can be designed as illustrated below.

THE CASSETTE MUST ALWAYS REMAIN

CONNECTED TO ELECTRICAL SUPPLY TO ALLOW

THE DRAINAGE OF WATER CONDENSATS.

5.1 CONDENSATE EVACUATION

To ensure effective condensate evacuation, the downward

slope must be 1 cm per metre without any restricted or

ascending section.

600 mm

MAXI

1cm/m

50 mini

16max

ConneCtions

WARNING !

The condensate extraction height is limited to a maximum

of 0.60 metre.

For heights above 0.60 m, an auxiliary condensate pump

with a level regulator should be installed.Furthermore, a

siphon with a height of at least 50 mm must be provided

to avoid any unpleasant odours in the room.

5.2 HYDRAULIC CONNECTIONS

For the system to operate in complete safety,

regulating valves must be fitted, if they are not

already fitted at the factory.

The regulation valves are installed

inside the cassettes. A lock spanner

must be used for tightening the

pipe work.

The first time the cassettes are filled with water

to check the tightness of the circuits, they can

be filled on a temporary basis, without power

being connected to the unit. If, on the other hand,

continuous water circulation is planned, the units

must be connected to the power supply to ensure

condensate drainage by the draining pump and

to avoid the condensate tray overflowing.

WARNING !

For connecting the coils the use of stop cock valves with

flexible pipes is recommended.

It is imperative to envisage a support of these pipings

independently of the cassette.

The connection must not be over tightened.

The hot water coil air vent must be done through the water

outlet connection (8).

It should be noted that over tightening the connections can

cause excessive material constraints during high temperature

operation.

The use of regulation valves (factory-fitted, supplied as an

accessory or by the client) is mandatory to ensure that the

appliance operates correctly.

The installation and operating conditions require the

MANDATORY fitting of a valve ON the unit OR/AND

upstream in the hydraulic circuit. This is to prevent

chilled water from circulating in the appliance when

the fan is not operational (condensation issue) or to

prevent the simultaneous circulation of chilled water

and hot water in a 4-pipes exchanger.

Chilled Water Cassette

6.1 ELECTRICAL CONNECTION

eleCtriCal ConneCtion

Take care !

Before starting any electrical connection, check

that the electrical supply corresponds to the

specification indicated on the unit’s maker’s plate.

Each cassette in equipped with a terminal block

located inside the cassette cabinet.

Connection to the electrical network must comply with

current electrical standards.

The unit must be earthed.

The manufacturer and their representatives decline all

responsibility for any accidents caused by inadequate or

non-existent earthing of the installation.

All the cassettes are intended to operate on a normal voltage

of 230V ± 10% / 1 phase / 50Hz + Earth or 3N~400V

± 10% / 50Hz.

The wiring diagram affixed to the unit illustrates the

connections to be made.

6.2 CHANGE OVER SENSOR

CONNECTION (MODELS 2T)

Depending on the season, the cassette units are either

supplied with hot water in winter or with chilled water in

summer and during the mid season periods. A 3-way

valve must be installed on the water circuit supplying

the unit.

Summer and mid-season: The 3 way valve is controlled

by the thermostat to obtain cooling.

Winter: The 3 way valve is controlled by the thermostat

to obtain heating.

CHANGE OVER SENSOR

The change over sensor supplied in the unit is to be located

on the water inlet pipe. It enables the thermostat action to

be reversed in relation to water temperature.

THERMOSTAT INSTALLATION

WARNING:

The thermostat is already wired up at the factory.

1. Shut off the unit’s electrical power supply.

2. Fit the thermostat on the water inlet pipe.

3. Cover the connection with a protective

sheath.

WATER TEMPERATURE PROBE INSTALLATION

The SW probe supplied in the unit is to be located on the

water inlet pipe.

WARNING:

The SW probe is already wired at the factory.

1. Cut the power supply to the unit.

2. Fit the probe onto the water inlet pipe.

3. Cover the connection with a protective

sheath.

INSULATE IMPERATIVELY

A device to disconnect all the power conductors with

an approved minimum opening distance must be

included in the mains power supply according to

best installation practices.

Temperature effect: T° < 15 °C - T° > 30 °C.

Chilled Water Cassette

6.3 ELECTRIC HEATING

Each electric heating system is equipped with 2 SAFETY

DEVICES. One is reset automatically, the other is manually

reset. They cut off electrical supply to the heating resistances

as soon as an operating anomaly is detected.

The electrical coil must never operate without the

fan turning.

6.4 FAULT WARNING REPEATER

When the upper water level is reached (SB2 detector), the

pump electronic logic control shuts down ventilation, heating

and the cooling valve with one of its wires connected to

terminal 2.

A default relay (KD) or a warning light (I max 4A / 250 V) can

be connected to terminal 6 (230 V NEUTRAL potential).

Provide electrical supply to the system on the same

phase and coming from the same circuit protection

device as the cassette.

Manual reset

6.5 VENTILATION SPEEDS

The cassettes are supplied with 3 fan speeds, wired

according to the model. Depending on the application, it

is possible to select from the 6 speeds, by connecting the

motor wires on standby.

Take care !

The disconnected, unused wire must be isolated in

accordance with best electrical wiring practices.

eleCtriCal ConneCtion ContinueD

6.6 WIRING DIAGRAM

This wiring diagram is correct at the time of

publication. Manufacturing changes can lead

to modifications. Always refer to the diagram

supplied with the product.

Take care !

SEE APPENDIX

Chilled Water Cassette

eleCtriCity

The unit must be installed and fitted in

accordance with current safety standards

by a qualified technician.

Fitting height: about 1.50 m above floor level.

Take care not to locate the thermostat in draughts created

by doors and windows.

7.1 THERMOSTAT LOCATION

Also ensure that the thermostat is located in the room’s

normal thermal currents and that it is not located in shelving

or covered by curtains.

Any source of parasitic heat negatively influences

temperature regulation accuracy. Therefore, avoid the sun’s

rays or proximity to portable heating devices, electric lights,

chimneys, televisions, etc...

INFRA RED VERSION - INFRA RED REMOTE CONTROL

USE

Three modes available:

² Cooling

² Heating

² Auto

For each of these modes, fan ventilation can be configured

in LS, MS, HS and Auto Ventilation modes.

7.2 CONTROL

Chilled Water Cassette

eleCtriCity ContinueD

ON / OFF key

Operating mode selection key for

COOLING

HEATING

AUTOMATIC COOLING / HEATING

REGULATION, FAN ONLY

I FEEL key: local detection of temperature

VENTILATION SPEED or AUTOMATIC

VENTILATION selection key

Set point increase key

Set point decrease key

SLEEP key (unoccupied mode)

"+" key: increases the operating time

"-" key: decreases the operating time

Liquid crystal diode display

I FEEL sensor

Infrared signal transmitter

ROOM key: display of the ambient temperature

LOCK key

SET key:Press for 5 seconds to set the time

RESET FUNCTION:

1. Remove one battery

2. Simultaneously press these 4 keys until the symbols are

no longer displayed

3. Reinstall the battery

NOTE :

Open the cover / flap to access the control keys.

The four keys to be pressed are:

The other buttons , , and of the

remote control are not active in this version.

"Timer" function is available only in option with

remote control µBMS/RCW2

The Timer function is not available with Aquanet.

Chilled Water Cassette

Medium speedHigh Speed

Lown Speed

ROOM THERMOSTAT TRM-VP AND TRM-FA

SWITCHES

Switch 0 - I

² ON "I"

² OFF "0"

Linear switch

² COOLING

² HEATING

eleCtriCity ContinueD

USE

The room thermostat of the air conditioner regulates the

room temperature. It is designed for closed, dry rooms such

as flats, offices, etc.

Maximum acceptable relative humidity of the air : 95%. This

value should not be exceeded.

Avoid condensation.

DIMENSIONS

WALL MOUNTING

² Remove the thermostat control knob, the

screw and the cover.

² On a flat surface, mount the control panel

using plugs and screws.

² Install the cover, the screw and the thermostat

control knob.

ELECTRICAL CONNECTIONS

Connection of the thermostat TRM-VP and TRM-FA.

Connections should be made according to the diagram

(SEE APPENDIX).

Max. cross-sectional area of wires : 2,5 mm

TECHNICAL CHARACTERISTICS

Operating voltage 230V 50Hz

Contact configuration SPDT

Temperature range 5 to 30°C

Switching current at 230V AC 6A (cos ϕ=1) / 3A (cos ϕ =0.6)

Switching differential approx. 0,5 K

Sensor system bimetal

Switches

ON / OFF

mode of operation

fan speed

Chilled Water Cassette

eleCtriCity ContinueD

FINAL OPERATIONS

ADJUSTMENT OF THE TEMPERATURE

RANGE

The room thermostat is set in the factory for a minimum

temperature of +5°C and a max. temperature of +30°C.

Two rings are provided inside the knob for reducing the

temperature range.

² Example: 12°C to 25°C.

ADJUSTMENT PROCEDURE

1. Setting the temperature range

e.g. max. 25°C, min. 12°C.

2. Remove the control knob.

3. Use a pointed object to align the mark on

the red ring (max. value) with the desired

maximum temperature (25°C), turning the

red index opposite the outside numbers

counterclockwise.

4. Use a pointed object to align the mark on

the blue ring (min. value) with the desired

minimum temperature (12°C), turning the

blue index opposite the inside numbers

clockwise.

5. Install the control knob.

The temperature ranges can be graduated in:

² degrees Celsius °C

from 5°C to 30°C

² number 1 to 6

1=5°C

2=10°C

3=15°C

4=20°C

5=25°c

6=30°C

Chilled Water Cassette

eleCtriCity ContinueD

TAE20 ROOM THERMOSTAT

FIELDS OF APPLICATION

² Regulating ambient temperature in rooms

heated or cooled.

² Opening and closing the valve.

² Cutting in and out the electric heating.

² Controlling the three fan speed.

DESCRIPTION

The unit comprises two parts:

² A plastic case, housing the electronics, the

controls and an internal ambience sensor.

² A mounting plate.

The case is hooked onto the fitted mounting plate, then

click fastened.

The screw terminal connections are located on the mounting

plate, with the DIP switches on the back of the case.

ADJUSTMENT AND CONTROL

ELEMENTS

² Operating mode switch "ON-OFF" and

manual fan speed selection).

² Electro-luminescent diodes for displaying the

heating and cooling modes and the fan.

² Minimum temperature setting limiter

(adjustable by increments of 1 K). Mechanical

stop accessible by removing the button 5.

² Maximum temperature setting limiter

(adjustable by increments of 1 K). Mechanical

stop accessible by removing the button 5.

² Ambient temperature setting adjustment

button.

² Set of DIP switches.

2 3 4

5 6 1

REFER TO SPECIAL TAE 20 ROOM THERMOSTAT MANUAL

Chilled Water Cassette

8.1

AIR DISTRIBUTION MODULE FITTING

Carefully unpack the module and fit the clips in the frame

corners.

For infra red models, connect the flat cable from the

receiver.

Present the frame to the unit, and apply pressure so that the

clips engage. Then screw it in place.

8.2 FILTER INSTALLATION

The seals are illustrated in the diagram below. They

avoid:

A Air by pass

B Treated air being distributed into the suspended

ceilling space.

After installation, check that the gap between the frame and

the suspended ceiling is less than 5 mm.

5 mm

install the central grille by twisting

Avoid distorsions of the frame caused by excessive traction;

the frame should be correctly centered in relation to the false

ceiling and it should especially ensure an airtight separation

between air succion and air discharge.

A B

air Distribution

Place the air intake grille hinges in the openings: rep A

Install the filter in the location provided: rep B

Close the grille with the locks on both sides.

La page charge ...

Airwell WKW 45 2T Installation and Maintenance Manual

Marque: Airwell

Modèle: WKW 45 2T

Catégorie: Climatiseurs split-system

Taper: Installation and Maintenance Manual

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Airwell WKW 45 2T

Airwell WKW 45 2T Installation and Maintenance Manual

Ce manuel convient également à

Airwell WKW 45 2T Installation and Maintenance Manual

dans d''autres langues

Documents connexes

Autres documents