Maytag MFT2672AEM10 Le manuel du propriétaire

TABLE OF

Congratulations on your purchase and welcome to

the Maytag Brand family of high-quality

appliances. Your new Maytag French Door

Refrigerator combines advanced cooling

technology with simple operation and high

efficiency.

REFRIGERATOR SAFETY ........................................................ 3

Proper Disposal of Your Old Refrigerator .............................. 3

PARTS AND FEATURES .......................................................... 4

What's New Behind the Doors? ............................................. 4

INSTALLATION INSTRUCTIONS ............................................ 5

Unpack the Refrigerator ......................................................... 5

- Remove the Packaging ......................................................... 5

- Clean Before Using ............................................................... 5

Location Requirements .......................................................... 5

Remove and Replace Refrigerator Doors .............................. 6

- Remove Right-Hand Refrigerator Door ................................ 7

- Remove Left-Hand Refrigerator Door. .................................. 7

- Replace Right-Hand Refrigerator Door ................................ 8

- Replace Left-Hand Refrigerator Door ................................... 8

- Final Steps ............................................................................. 8

Remove and Replace Freezer Drawer Front .......................... 8

- Remove Drawer Front ........................................................... 8

- Replace Drawer Front ........................................................... 9

- Final Steps ............................................................................. 9

Electrical Requirements .......................................................... 9

Water Supply Requirements ................................................ 10

Connect the Water Supply ................................................... 10

- Connectto WaterLine ....................................................... 10

- Connect to Refrigerator ..................................................... 11

- Complete the Installation ................................................... 11

Handle Installation and Removal .......................................... 12

- Install Handles .................................................................... 12

- Remove the Handles .......................................................... 12

Refrigerator Leveling, Door Closing and Alignment ............. 13

FILTERS AND ACCESSORIES .............................................. 14

Water Filtration System ........................................................ 14

- Install the WaterFilter. ........................................................ 14

- The Water Filter Status Light ............................................. 14

- Replace the Water Filter. .................................................... 15

Install Air Filter ...................................................................... 15

- Installing the Air Filter ......................................................... 15

- Installing the Filter Status Indicator. ................................... 15

- Replacing the Air Filter ....................................................... 16

Install Produce Preserver ..................................................... 16

- Installing the Produce Preserver ....................................... 16

- Installing the Status Indicator. ............................................ 17

- Replacing the Produce Preserver ...................................... 17

Accessories .......................................................................... 17

REFRIGERATOR USE ............................................................ 18

Opening and Closing Doors ................................................. 18

Using the Controls ................................................................ 18

- Viewing andAdjusting Temperature Set Points ................ 18

- Cooling On/Off ................................................................... 19

CONTENTS

Each appliance that leaves our factory is inspected

thoroughly to ensure that it is working properly.

Please read the Use and Care Instructions in this

guide before operating your new refrigerator. Like

all appliances, your refrigerator may require

maintenance or repair from time to time, but you

can help to ensure that your refrigerator provides

many years of reliable service by following the

instructions in this guide.

Options ............................................................................... 20

- Additional Features ............................................................ 20

Water and Ice Dispensers .................................................... 21

- Flush the Water System ..................................................... 21

The Water Dispenser .......................................................... 21

The Ice Dispenser. .............................................................. 21

Dispensing .......................................................................... 21

The Dispenser Light ........................................................... 22

The Dispenser Lock. ........................................................... 22

Ice Maker and Ice Storage Bin ............................................ 22

- Ice Production Rate ........................................................... 22

Style 1 - Ice Maker in the Refrigerator ............................... 22

Style 2 - Ice Maker in the Freezer ...................................... 23

REFRIGERATOR FEATURES ................................................ 23

Refrigerator Shelves ............................................................. 23

Shelves and Shelf Frames .................................................. 23

Crisper and Crisper Cover ................................................... 24

Crisper Humidity Control ..................................................... 24

Temperature-Controlled Drawer .......................................... 24

Style 1 - Electronic Control ................................................ 24

Style 2 - Manual Control .................................................... 24

Drawer Removal and Replacement ................................... 25

Drawer Divider .................................................................... 25

- Meat Storage Guide ........................................................... 25

DOOR FEATURES .................................................................. 25

Door Bins ............................................................................. 25

FREEZER FEATURES ............................................................ 25

Pizza Pocket and Drawer Divider ........................................ 25

REFRIGERATOR CARE ......................................................... 26

Cleaning ............................................................................... 26

- Exterior Cleaning ................................................................ 26

- Interior Cleaning ................................................................. 26

Condenser Cleaning ........................................................... 27

Lights .................................................................................... 27

Vacation and Moving Care .................................................. 27

Vacations ............................................................................ 27

- Moving ................................................................................ 27

TROUBLESHOOTING ............................................................ 28

Operation ............................................................................. 28

Noise .................................................................................... 29

Temperature and Moisture .................................................. 30

Ice and Water ....................................................................... 31

Doors .................................................................................... 33

WATER FILTER CERTIFICATIONS ...................................... 34

PERFORMANCE DATA SHEET ............................................ 35

WARRANTY ............................................................................ 36

SERVICE NUMBERS ......................................... BACK COVER

2

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages inthis manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

• Plug into a grounded 3 prong outlet.

• Do not remove ground prong.

• Do not use an adapter.

• Do not use an extension cord.

• Disconnect power before servicing.

• Replace all parts and panels before operating.

• Remove doors from your old refrigerator.

• Use nonflammable cleaner.

• Keep flammable materials and vapors, such as gasoline,

away from refrigerator.

• Use two or more people to move and install refrigerator.

• Disconnect power before installing ice maker (on ice maker

kit ready models only).

• Use a sturdy glass when dispensing ice (on some models).

• Do not hit the refrigerator glass doors (on some models).

SAVE THESE INSTRUCTIONS

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other

reproductive harm.

Proper DisposaJ of

Your Old Refrigerator

Suffocation Hazard

Remove doors from your old refrigerator.

Failure to do so can result in death or brain damage.

IMPORTANT: Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are still dangerous

- even if they will sit for "just a few days." If you are getting rid of

your old refrigerator, please follow these instructions to help

prevent accidents.

Before You Throw Away Your Old Refrigerator or

Freezer:

• Take off the doors.

• Leave the shelves in place so that children may not easily

climb inside.

Important information to know about disposal of

refrigerants:

Dispose of refrigerator in accordance with Federal and Local

regulations. Refrigerants must be evacuated by a licensed,

EPA certified refrigerant technician in accordance with

established procedures.

PARTS AND FEATURES

A B C

i!i!

D

E

F

A. Ice maker

B.Air filter

C. Water filter

D. Door bins

E. Crispers

F. Pantry drawer

G. Freezer drawer

H. LED ramp-on lighting

I. In-Door-Ice ®ice

dispensing system

What's New Behind the Doors?

Your Maytag °French Door Refrigerator comes equipped with various

innovative storage and energy efficient features.

Energy and Normal Operating Sounds

Your new French Door Bottom Mount refrigerator has been

designed to optimize energy efficiency, and better regulate

temperatures to match cooling demand. You may notice that it

operates differently than your previously owned refrigerator. It is

normal for the high-efficiency compressor to run for extended

periods of time at varying speeds in order to consume only the

energy necessary for optimum efficiency. In addition, during

various stages of the cooling cycle, you may hear normal

operating sounds that are unfamiliar to you.

More Storage Space

The French Door Bottom Mount has the most fresh food storage

space available, including a full-width, temperature controlled,

pantry drawer perfect for storing veggie trays or party platters.

In-Door-Ice ° Ice Dispensing System

The ice storage bin located in the door provides an entire extra

shelf of storage space, and the storage bin is removable for easy

access to filtered ice.

Dual Evaporator (on some models)

The refrigerator compartment and freezer compartment have

separate evaporators to provide fresh food and frozen food with

separate climates. The refrigerator stays cool and humid for the

optimum storage of fresh foods while the freezer stays cold and

dry. Humidity from the refrigerator does not mix with dry freezer

air, so frost is controlled, which reduces freezer burn. Since no air

is shared between the refrigerator and freezer, the transfer of food

odors and tastes from the refrigerator to the freezer is eliminated.

Water Filter

NSF®Certified filter reduces chlorine taste and odor, particulates

(class I), lead, and mercury. Replacing the water filter every

6 months ensures clean, filtered drinking water.

Air Filter

An air filter is 15 times more powerful than baking soda at

reducing common food odors inside the refrigerator.

Produce Preserver (on some models)

Ethylene is a natural gas produced by fruits and vegetables to

promote ripening. The Produce Preserver absorbs ethylene, to

delay the over-ripening of fresh produce. As a result, certain

produce items will stay fresh longer.

LED Lighting

The LED lights do not ever need to be replaced.

Door Alarm

A helpful alarm sounds when the refrigerator door or freezer

drawer is left ajar.

Power Outage Indicator (on some models)

If the power should go out while you are away from home, this

indicator will let you know that the refrigerator has been without

power.

4

INSTALLATION INSTRUCTIONS

Unpack the Refrigerator

Excessive Weight Hazard

Use two or more people to move and install

refrigerator.

Failure to do so can result in back or other injury.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator for

cleaning or service, be sure to cover the floor with

cardboard or hardboard to avoid floor damage. Always pull

the refrigerator straight out when moving it. Do not wiggle or

"walk" the refrigerator when trying to move it, as floor

damage could occur.

Remove the Packaging

• Remove tape and glue residue from surfaces before turning

on the refrigerator. Rub a small amount of liquid dish soap

over the adhesive with your fingers. Wipe with warm water

and dry.

• Do not use sharp instruments, rubbing alcohol, flammable

fluids, or abrasive cleaners to remove tape or glue. These

products can damage the surface of your refrigerator. For

more information, see "Refrigerator Safety."

• Dispose of/recycle all packaging materials.

Clean Before Using

After you remove all of the packaging materials, clean the inside

of your refrigerator before using it. See the cleaning instructions

in "Refrigerator Care."

important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

Tempered glass is designed to shatter into many small,

pebble-size pieces. This is normal. Glass shelves and covers

are heavy. Use both hands when removing them to avoid

dropping.

Location Requirements

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

IMPORTANT: This refrigerator is designed for indoor, household

use only.

To ensure proper ventilation for your refrigerator, allow for a 1/2"

(1.25 cm) of space on each side and at the top. Allow for a 1"

(2.54 cm) space behind the refrigerator. Ifyour refrigerator has an

ice maker, allow extra space at the back for the water line

connections. When installing your refrigerator next to a fixed wall,

leave a 33/4'' (9.5 cm) minimum space between the refrigerator

and wall to allow the door to swing open.

NOTE: This refrigerator is intended for use in a location where the

temperature ranges from a minimum of 55°F (13°C) to a

maximum of 110°F (43°C). The preferred room temperature range

for optimum performance, which reduces electricity usage and

provides superior cooling, is between 60°F (15°C) and 90°F

(32°C). It is recommended that you do not install the refrigerator

near a heat source, such as an oven or radiator.

]L

/

1/2" (1.25 cm) /

33/4" (9.5 cm)

i

/

\_

Remove and Replace Refrigerator Doors

NOTE: Measure the width of your door opening, to see whether or not you need to remove the refrigerator doors to move the

refrigerator into your home. If door removal is necessary, see the following instructions.

IMPORTANT: If the refrigerator was previously installed and you are moving it out of the home, before you begin, turn the refrigerator

control OFE Unplug the refrigerator or disconnect power. Remove food and adjustable door or utility bins from doors.

Gather the required tools and read all instructions before removing doors.

TOOLS NEEDED: 3/le" hex key wrench and a #2 Phillips screwdriver

Electrical Shock Hazard

Disconnect power before removing doors.

Failure to do so can result in death or electrical shock.

Style 1 - Water Dispenser

Tubing Connection

\

A

A. Ou_rR_g

Wiring Plug

Top Left Hinge

A B

c

A. _6" Internal Hex-Head Screws

B. Ground Wire (Do Not Remove)

C. Do Not Remove Screws

Style 2 - Water Dispenser

Tubing Connection

\

A

A. Outer Ring

A. _8"lnternal Hex-Head Screws

B. Hinge Cover Screw

C. Top Hinge Cover

D. Top Hinge

6

Remove Right-Hand Refrigerator Door

Electrical Shock Hazard

Disconnect power before removing doors.

Failure to do so can result in death or electrical shock.

1. Unplug refrigerator or disconnect power.

2. Keep the refrigerator doors closed until you are ready to lift

them free from the cabinet.

NOTE: Provide additional support for the refrigerator door

while the hinges are being removed. Do not depend on the

door gasket magnets to hold the door in place while you are

working.

3. Using a Phillips screwdriver, remove the cover from the Top

Hinge.

4. Using the 3/H' hex key wrench, remove the two internal hex

head screws from the top hinge, and set aside.

NOTE: Do not remove the two Iocator screws. These screws

will help you align the hinge when you replace the door.

D

A

Remove Left-Hand Refrigerator Door

IMPORTANT: The tubing and wiring for the water dispenser run

through the left-hand door hinge, so they must be disconnected

before removing the door.

1. Using a Phillips screwdriver, remove the cover from the top

hinge.

................... .................................'I

B

A. Tophinge coverscrew B. Top hinge cover

2=

Disconnect the water dispenser tubing located on top of the

door hinge.

Style 1 - Press the outer ring against the face of the fitting

and gently pull the dispenser tubing free.

NOTE: The water dispenser tubing remains attached to the

left-hand refrigerator door.

\

5=

A. Top hinge cover screw

B. Top hinge cover

C. _" Internal hex head screws

D. Top hinge

Excessive Weight Hazard

Use two or more people to lift the refrigerator door.

Failure to do so can result in back or other injury.

Lift the refrigerator door from the bottom hinge pin. The top

hinge will come away with the door.

A. Outer ring

Style 2 - Firmly pull up on the clasp. Then, pull the tubing out

of the fitting.

NOTE: The water dispenser tubing remains attached to the

left-hand refrigerator door.

\

3.

4,

Disconnect the wiring plug located on top of the door hinge.

• Grasp each side of the wiring plug. With your left thumb,

press down to release the catch and pull the sections of

the plug apart.

NOTE: Do not remove the green, ground wire. It should

remain attached to the door hinge.

Using the ¾e" hex key wrench, remove the two internal hex

head screws from the top hinge, and set aside.

NOTES:

Provide additional support for the refrigerator door while

the hinges are being removed. Do not depend on the door

gasket magnets to hold the door in place while you are

working.

Do not remove the two Iocator screws. These screws will

help you align the hinge when you replace the door.

A B

C

A. _" Internal hex head screws

B. Ground wire (do not remove)

C. Locator screws (do not

remove)

5,

Lift the refrigerator door from the bottom hinge pin. The top

hinge will come away with the door.

NOTE: It may not be necessary to remove the bottom hinges

and brake feet assemblies to move the refrigerator through a

doorway.

• Only if necessary, use a driver with a #2 square bit tip to

remove the bottom hinges and a 3/8"nut driver to remove

the brake feet screws.

Replace Right-Hand Refrigerator Door

1. Set the right-hand door onto the bottom hinge pin.

2. Insert the top hinge pin into the open hole in the top of the

refrigerator door.

3. Using the two ¾e" internal hex head screws, fasten the hinge

to the cabinet. Do not tighten the screws completely.

Replace Left-Hand Refrigerator Door

IMPORTANT: Do not intertwine the water tubing and wiring

bundles when reconnecting them.

1. Set the left-hand door onto the bottom hinge pin.

2. Using the two ¾e" internal hex head screws, fasten the hinge

to the cabinet. Do not tighten the screws completely.

3. Reconnect the water dispenser tubing.

Style 1 - Insert the tubing into the fitting until it stops and the

outer ring is touching the face of fitting.

Style 2 - Insert the tubing firmly into the fitting until it stops.

Close the clasp around the tubing. The clasp snaps into place

between the fitting and the collar.

4. Reconnect the electrical wiring.

• Push together the two sections of the wiring plug.

Final Steps

1. Completely tighten the four internal hex head screws (two on

the right-hand door hinge and two on the left-hand door

hinge).

2. Replace both top hinge covers.

Remove and Replace Freezer Drawer Front

Depending on the width of your door opening, it may be

necessary to remove the freezer drawer front to move the

refrigerator into your home.

IMPORTANT:

• If the refrigerator was previously installed and you are moving

it out of the home, before you begin, turn the refrigerator

control OFF, and unplug the refrigerator or disconnect power.

Remove food from the freezer drawer.

Two people may be required to remove and replace the

freezer drawer front.

Tool Needed: 1/4"hex driver

Remove Drawer Front

1. Open the freezer drawer to its full extension.

2. Remove the two screws at the top, inside the drawer front

(one on the left-hand side and one on the right-hand side)

that fasten the drawer front to the drawer glides.

3.

4,

Lift up on the drawer front to release the plastic studs from

the drawer glide bracket slots.

A.Drawer glide bracket slots

Slide the drawer glides back into the freezer.

8

ReplaceDrawerFront

1. Pull out the freezer drawer glides to their full extension.

2. Holding the drawer front by its sides, align the two plastic

studs, located at the bottom, inside the drawer front, with the

drawer glide bracket slots.

NOTE: It helps if one person holds the drawer glides steady

while another person aligns the drawer front and inserts the

studs into the slots.

3=

A. Drawer front screw

B. Drawer front plastic stud

Replace and tighten the two screws at the top of the drawer

front (one on the left-hand side and one on the right-hand

side).

Final Steps

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

1. Plug into a grounded 3 prong outlet.

2. Reset the controls. See "Using the Control(s)."

3. Return all removable door parts to doors and the food to

refrigerator.

Electrical Requirements

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Fai}ure to fol}ow these instructions can result in death,

fire, or electrical shock.

Recommended Grounding Method

A 115 volt, 60 Hz, AC only 15- or 20-amp fused, grounded

electrical supply is required. It is recommended that a separate

circuit serving only your refrigerator be provided. Use an outlet

that cannot be turned off by a switch. Do not use an

extension cord.

NOTE: Before performing any type of installation, cleaning, or

removing a light bulb, turn Cooling OFF, and then disconnect the

refrigerator from the electrical source. When you have finished,

reconnect the refrigerator to the electrical source and turn

Cooling ON. See "Using the Control(s)."

Before you move your refrigerator into its final location, it is

important to make sure you have the proper electrical

connection.

Water Supply Requirements

A cold water supply with water pressure between 35 and 120 psi

(241 and 827 kPa) is required to operate the water dispenser and

ice maker. Ifyou have questions about your water pressure, call a

licensed, qualified plumber.

NOTE: If the water pressure is less than what is required, the flow

of water from the water dispenser could decrease or ice cubes

could be hollow or irregular shaped.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the

refrigerator needs to be between 35 and 120 psi (241 and

827 kPa).

If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

Check to see whether the sediment filter in the reverse

osmosis system is blocked. Replace the filter if necessary.

Allow the storage tank on the reverse osmosis system to refill

after heavy use. The tank capacity could be too small to keep

up with the requirements of the refrigerator.

NOTE: Faucet mounted reverse osmosis systems are not

recommended.

• If your refrigerator has a water filter, it may further reduce the

water pressure when used in conjunction with a reverse

osmosis system. Remove the water filter. See "Water

Filtration System."

If you have questions about your water pressure, call a licensed,

qualified plumber.

Connect the Water Supply

Read all directions before you begin.

IMPORTANT:

• Plumbing shall be installed in accordance with the

International Plumbing Code and any local codes and

ordinances.

• To avoid off-taste or odor in your ice or water, it is

recommended that you use copper tubing or Whirlpool ®

supply tubing, Part Number 8212547RP to connect the

household water line with the water line or water fitting

coming from the back of the refrigerator. Check for leaks.

• Install tubing only in areas where temperatures will remain

above freezing.

TOOLS NEEDED:

Gather the required tools and parts before starting installation.

• Flat-blade screwdriver

• 7/le"and 1/2"open-end wrenches or two adjustable wrenches

• 1/4"nut driver

NOTE: Do not use a piercing-type or ¾e" (4.76 mm) saddle valve

which reduces water flow and clogs easier.

Connect to Water Line

IMPORTANT: Ifyou turn the refrigerator on before the water is

connected, turn the ice maker OFF.

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water.

3.

4.

Use a quarter-turn shutoff valve or the equivalent, served by a

1/2"household supply line.

NOTE: To allow sufficient water flow to the refrigerator, a

minimum 1/2"size household supply line is recommended.

A. Sleeve

B. Nut

C. Copper tubing (to refrigerator)

D. Household supply line (V2"minimum)

Now you are ready to connect the copper tubing to the

shutoff valve. Use 1/4"(6.35 mm) OD soft copper tubing to

connect the shutoff valve and the refrigerator.

• Ensure that you have the proper length needed for the

job. Be sure both ends of the copper tubing are cut

square.

Slip compression sleeve and compression nut onto

copper tubing as shown. Insert end of tubing into outlet

end squarely as far as it will go. Screw compression nut

onto outlet end with adjustable wrench. Do not

overtighten.

A. Compression sleeve

B. Compression nut

C. Copper tubing

10

5=

6=

Place the free end of the tubing into a container or sink, and

turn on main water supply to flush out tubing until water is

clear. Turn off shutoff valve on the water pipe.

NOTE: Always drain the water line before making the final

connection to the inlet of the water valve, to avoid possible

water valve malfunction.

Bend the copper tubing to meet the water line inlet, which is

located on the back of the refrigerator cabinet as shown.

Leave a coil of copper tubing to allow the refrigerator to be

pulled out of the cabinet or away from the wall for service.

Connect to Refrigerator

Follow the connection instructions specific to your model.

Style 1

1. Remove plastic cap from water valve inlet port. Attach the

copper tube to the valve inlet using a compression nut and

sleeve as shown. Tighten the compression nut. Do not

overtighten. Confirm copper tubing is secure by pulling on

copper tubing.

2. Create a service loop with the copper tubing. Avoid kinks

when coiling the copper tubing. Secure copper tubing to

refrigerator cabinet with a "P" clamp.

B

3=

u

D

A.Copper tubing C. Compression nut

B. "P" clamp D. Compressionsleeve

Turn on water supply to refrigerator and check for leaks.

Correct any leaks.

Style 2

1. Unplug refrigerator or disconnect power.

2. Remove and discard the short, black plastic part from the

end of the water line inlet.

3. Thread the nut onto the end of the tubing. Tighten the nut by

hand. Then tighten it with awrench two more turns. Do not

overtighten.

NOTE: To avoid rattling, be sure the copper tubing does not

touch the cabinet's side wall or other parts inside the cabinet.

A B C D

A. Household water line C. Ferrule (purchased)

B. Nut (purchased) D. Refrigerator water tubing

4. Install the water supply tube clamp around the water supply

line to reduce strain on the coupling.

5. Turn shutoff valve ON.

6. Check for leaks. Tighten any connections (including

connections at the valve) or nuts that leak.

7. On some models, the ice maker is equipped with a built-in

water strainer. If your water conditions require a second water

strainer, install it in the 1/4"(6.35 mm) water line at either tube

connection. Obtain a water strainer from your appliance

dealer.

...................C°mplete the lnstallati°n ...............................................................................................................................................................................................................................................................................

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Fai}ure to follow these instructions can result in death,

fire, or electrical shock.

1. Plug into a grounded 3 prong outlet.

2. Flush the water system. See "Water and Ice Dispensers."

NOTE: Allow 24 hours to produce the first batch of ice. Discard

the first three batches of ice produced. Allow 3 days to

completely fill the ice storage bin.

11

Handle Installation and Removal

Parts Included: Refrigerator door handles (2), Freezer drawer

handle (1), 1/8"hex key, spare setscrew(s)

Install Handles

NOTE: Handle mounting setscrews are preinstalled inside the

handle.

1. Remove the handles from the packaging inside the

refrigerator, and place them on a soft surface.

2. Open a refrigerator compartment door. On the closed door,

place a handle onto the shoulder screws so that the

setscrews are facing the adjacent door.

A_

9. With the freezer drawer closed, place the handle onto the

shoulder screws so that the setscrews are facing down

toward the floor.

.4

B

A. Shoulder screw

B. Setscrews inside the handle

10. Firmly push the handle toward the drawer until the handle

base is flush against the drawer.

11. Insert the short end of the hex key into the left-hand hole and

slightly rotate the hex key until it is engaged in the setscrew.

3.

4.

A. Shoulder screws

B. Setscrews inside the handle

Firmly push the handle toward the door until the handle base

is flush against the door.

While holding the handle, insert the short end of the hex key

into the upper hole and slightly rotate the hex key until it is

engaged in the setscrew.

5. Using a clockwise motion tighten the setscrew just until it

begins to contact the shoulder screw. Do not fully tighten.

6. Repeat steps 4 and 5 to fasten the lower setscrew.

7. Once both setscrews have been partially tightened as

instructed in the previous steps, fully tighten both setscrews.

IMPORTANT: When the screws feel tight, tighten them an

additional quarter-turn. The handle is not properly installed

without this extra tightening.

8. Repeat steps 2 through 7 to install the other handle onto the

adjacent refrigerator door.

12. Using a left to right motion tighten the setscrew a quarter-turn

at a time just until it begins to contact the shoulder screw. Do

not fully tighten.

13. Repeat steps 11 and 12 to fasten the right-hand setscrew to

the shoulder screw.

14. Once both setscrews have been partially tightened as

instructed in the previous steps, fully tighten both setscrews.

IMPORTANT: When the screws feel tight, tighten them an

additional quarter-turn. The handle is not properly installed

without this extra tightening.

15. Save the hex key and all instructions.

Remove the Handles

1. While holding the handle, insert the short end of the hex key

into a setscrew hole and slightly rotate the hex key until it is

engaged in the setscrew.

2. Using a right to left motion loosen the setscrew a quarter-turn

at a time.

3. Repeat steps 1 and 2 for the other setscrew. Slowly pull the

handle away from the door or drawer.

4. If necessary, use a Phillips screwdriver to remove the

shoulder screws from the door.

12

Refrigerator Leveling, Door Closing and Alignment

The base grille covers the adjustable brake feet and roller

assemblies located at the bottom of the refrigerator below the

freezer drawer. Before making any adjustments, remove the base

grille and move the refrigerator to its final location.

Tools Needed: 1/4"hex driver

Tools Provided: 1/8"hex key wrench

1. Remove the base grille. Grasp the grille firmly and pull it

toward you. Open the freezer drawer to access the brake

feet.

NOTE: To allow the refrigerator to roll easier, raise the break

feet by turning them counterclockwise. The front rollers will

be touching the floor.

C

2. Move the refrigerator to its final location.

3. Lower the brake feet, by turning them clockwise, until the

rollers are off the floor and both brake feet are snug against

the floor. This keeps the refrigerator from rolling forward when

opening the refrigerator doors or freezer drawer.

IMPORTANT: If you need to make further adjustments

involving the brake feet, you must turn both brake feet the

same amount to keep the refrigerator level.

4. Make sure the doors close easily. If you are satisfied with the

door opening and closing, skip the next section and go to

"Align the Doors." If, however, the doors do not close easily

or the doors pop open, adjust the tilt.

To Adjust the Cabinet Tilt:

• Open the freezer drawer. Use a 1/4"hex driver to turn both

brake feet clockwise the same amount. This will raise the

front of the refrigerator. It may take several turns to allow

the doors to close easier.

NOTE: Having someone push against the top of the

refrigerator takes some weight off the brake feet. This

makes it easier to turn them.

Style 1

0

A. Brake foot

B. Front roller

B

5,

Style 2

A

A. Brake foot

/

Make sure the doors are even at the top and that the space

between the bottom of the refrigerator doors and the top of

the freezer drawer is even. If necessary, align the doors.

To Align the Doors:

Keeping both refrigerator doors closed, pull out the

freezer drawer. Locate the bottom hinge pin of the

right-hand refrigerator door. The alignment screw is inside

the bottom hinge pin.

Insert the short end of the 1/8"hex key wrench (packed

with the Door Handle Installation Instructions) into the

bottom hinge pin until it is fully engaged in the alignment

screw.

To raise the refrigerator door, turn the hex key to the right.

To lower the door, turn the hex key to the left.

Continue to turn the alignment screw until the doors are

aligned.

6.

7,

A. Bottom hinge pin

B. _" Hex key wrench

Make sure the refrigerator is steady. Ifthe refrigerator seems

unsteady or rolls forward when the door or drawer is pulled

open, adjust the brake feet.

To Steady the Refrigerator:

Open the freezer drawer. Using a 1/4"hex driver, turn both

brake feet clockwise the same amount until the brake feet

are snug against the floor. Check again. If not satisfied,

continue to adjust the brake feet by half turns of the

screw until the refrigerator does not roll forward when the

drawer is opened.

NOTE: Having someone push against the top of the

refrigerator takes some weight off the brake feet. This

makes it easier to turn the screws.

Replace the base grille by aligning the ends of the grille with

the leveling assemblies on each side and snapping the grille

into place.

13

FILTERS AND ACCESSORIES

Water Filtration System

Do not use with water that is microbiologically unsafe or

of unknown quality without adequate disinfection before

or after the system. Systems certified for cyst reduction

may be used on disinfected waters that may contain

filterable cysts.

5,

Turn the filter clockwise 90 degrees (1/4turn), until it locks into

the housing.

NOTE: If the filter is not correctly locked into the housing, the

water dispenser will not operate. Water will not flow from the

dispenser.

Install the Water Filter

1. Locate the accessory packet in the refrigerator and remove

the water filter.

2. Take the water filter out of its packaging and remove the

cover from the O-rings. Be sure the O-rings are still in place

after the cover is removed.

3,

A. O-ring cover

B. O-rings

The water filter compartment is located in the right-hand side

of the refrigerator ceiling. Push up on the compartment door

to release the catch, then lower the door.

4. Align the arrow on the water filter label with the cutout notch

in the filter housing and insert the filter into the housing.

6,

7,

While the compartment door is still open, lift the filter up into

the compartment. Then, close the filter compartment door

completely.

Flush the water system. See "Flushing the Water Filter" in the

"Water and Ice Dispensers" section.

IMPORTANT: If you do not flush the water system, you may

experience dripping and/or decreased flow from the water

dispenser.

The Water Filter Status Light

_H_HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH_;_HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH_HHHHHHHHHHHHHHHHHHHHH_HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH

Press WATER FILTER to display the percentage of filter life

remaining (from 99% to 0%). Press WATER FILTER again to

return to the Normal screen.

The water filter status lights will help you know when to change

your water filter.

• ORDER (yellow) - it is almost time to change the water filter.

• REPLACE (red) - Replace the water filter. While you are

dispensing water, "Replace" will blink.

NOTE: If a water filter is not installed or is undetected

because it is not properly installed (locked into place),

"Replace" and "--% remaining" will display on the control

panel. Check the water filter.

• RESET the water filter status tracking feature. After you

replace the disposable filter with a new filter, closing the filter

compartment door will automatically reset the filter status

tracking feature. See "Using the Controls."

NOTE: "Replace" will remain illuminated if a filter is not

installed or installed incorrectly.

14

ReplacetheWaterFilter

To purchase a replacement water filter, see "Accessories." 2.

Replace the disposable water filter when indicated on the water

filter status display or at least every 6 months. If water flow to

your dispenser or ice maker decreases noticeably, change the

water filter sooner. 3.

1. Locate the water filter compartment in the right-hand side of

the refrigerator ceiling. Push up to release and lower the

compartment door.

Turn the water filter counterclockwise (to the left), and pull it

straight out of the compartment.

NOTE: There may be some water in the filter. Some spilling

may occur. Use a towel to wipe up any spills.

Install the replacement water filter by following steps 2

through 7 in the "Install the Water Filter" section.

Install Air Filter (on some models)

An air filter is 15 times more powerful than baking soda at

reducing common food odors inside the refrigerator.

On some models, your refrigerator's accessory packet includes

an air filter, which must be installed prior to use.

Installing the Filter Status Indicator

The filter comes with a status indicator, which should be

activated and installed at the same time the air filter is installed.

Installing the Air Filter

Install the air filter behind the vented door, located on the rear

wall near the top of the refrigerator compartment.

1. Remove the air filter from its packaging.

2. Lift open the vented door.

3. Snap the filter into place.

A.Air filter

1=

2.

3=

A

Place the indicator face-down on a firm, flat surface.

Apply pressure to the bubble on the back of the indicator until

the bubble pops to activate the indicator.

Lift open the vented air filter door. On some models, there are

notches behind the door.

Models with notches:

• With the indicator screen facing outward, slide the

indicator down into the notches.

NOTE: The indicator will not easily slide into the notches

if the bubble has not been popped.

B

A. Air filter status indicator

B. Notches

15

A ................................../ I

Close the air filter door, and check that the indicator is

I

i i

visible through the window in the door.

A. Status indicator window

Models without notches:

• Place the indicator somewhere it is easily visible - either

inside the refrigerator, or elsewhere in your kitchen or

home.

Replacing the Air Filter

:::::::::::::::::_,_,;tHHHHHHHHHHHHHHHHHH_H_HHHHHHHHHHH__,_,,_HHHHHHHHHHHHHHHHHH__HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH_,_HHHHHHHHH__H_HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH__,,_HHHHHHHHHHHHHHHHHHHH_

The disposable air filter should be replaced every 6 months,

when the status indicator has completely changed from white to

red.

To order a replacement air filter, contact us. See "Accessories"

for information on ordering.

1. Remove the used air filter by squeezing in on the side tabs.

2. Remove the used status indicator.

3. Install the new air filter and filter status indicator using the

instructions in the previous sections.

Install Produce Preserver (on some models)

The produce preserver absorbs ethylene, to slow the ripening

process of many produce items. As a result, certain produce

items will stay fresh longer.

Ethylene production and sensitivity varies depending on the type

of fruit or vegetable. To preserve freshness, it is best to separate

produce with sensitivity to ethylene from fruits that produce

moderate to high amounts of ethylene.

Apples

Asparagus

Berries

Broccoli

Cantaloupe

Carrots

Citrus Fruit

Grapes

Lettuce

Pears

Spinach

Sensitivity to

Ethylene

High

Med.

Low

High

Med.

Low

Med.

Low

High

Ethylene

Production

Very High

Very Low

Low

Very Low

High

Very Low

Very High

Very Low

Installing the Produce Preserver

CAUTION: IRRITANT

MAY IRRITATE EYES AND SKIN. DANGEROUS FUMES

FORM WHEN MIXED WITH OTHER PRODUCTS.

Do not mix with cleaning products containing ammonia,

bleach or acids. Do not get in eyes, on skin or clothing. Do

not breathe dust. Keep out of reach of children.

FIRST AID TREATMENT: Contains potassium

permanganate. If swallowed, call a Poison Control Center or

doctor immediately. Do not induce vomiting. If in eyes, rinse

with water for 15 minutes. If on skin, rinse with water.

1. Find the Produce Preserver housing inside the refrigerator.

2. Open the housing by pulling up and out on the back.

3. Remove the FreshFIow TM Produce Preserver pouches from

the packaging and place them into the housing.

NOTE: For best performance, always use two pouches.

4. Place the Produce Preserver housing onto the tab located on

the back wall of the crisper drawer.

16

Installing the Status Indicator

The produce preserver comes with a status indicator, which

should be activated and installed at the same time the pouches

are installed.

_,,_,_ _,_,_t,,,,r_,_,_,,,,,,r_,_,,_,,_,,,_,_,_,_,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,r_,_,_,,,,,,,,,,,,,,,,,,,,_,,_,_,,_,_,_,,5,,,,,,,,,,,,,,,,,,,,,,,,,,,,r_,_,_,, ,_,,_,_,_,__,,_,,,,,,_,,,,,,,r_,_t,,,,,,,,,,,,,,,,,,,,_,_t,,,,,,,,,,,,,,,,,r_,_,_,_,_,_t,_t,_,_,_,_,,_,,_,,_,,_,,_,,_,,_,,_,,_,,_,,_,,_,,_,,_,,_,,_,,_,,_,,_,,_,,_,,_,,_,,_,,_,,_,,_,,_,,_,,_,,_,,_,,_,,_,,_,,_,,_,,_,,_,,_,,_,,_,,_,,_,,_,,_,,

Replacing the Produce Preserver

The disposable pouches should be replaced every 6 months or

when the status indicator changes completely from white to red.

To order replacements, contact us. See "Accessories" for

information on ordering.

1. Remove the used pouches from the produce preserver

housing.

2. Remove the used status indicator.

3. Install the replacement pouches and status indicator using

the instructions in the previous sections.

1. Place the indicator face-down on a firm, flat surface.

2. Apply pressure to the bubble on the back of the indicator until

the bubble pops, to activate the indicator.

3. Slide open the cap on the top of the produce preserver

housing.

4. Place the indicator in the top of the housing, facing outward.

5. Slide the cap closed, and check that the indicator is visible

through the rectangular hole in the cap.

NOTE: The cap will not easily close if the indicator's bubble

has not been popped.

Accessories

The following accessories are available for your refrigerator. To

order an accessory, contact us and ask for the Part Number.

In the U.S.A., visit our webpage www.maytag.com/accessories

or call 1-800-901-2042.

In Canada, visit our webpage www.whirlpoolparts.ca

or call 1-800-807-6777.

affresh ®Stainless Steel Cleaner:

In U.S.A., order Part #W10355016

In Canada, order Part #W10355016B

affresh ®Stainless Steel Wipes:

In U.S.A., order Part #W10355049

In Canada, order Part #W10355049B

affresh ®Kitchen & Appliance Cleaner:

In U.S.A., order Part #W10355010

In Canada, order Part #W10355010B

Water Filter:

Order Part #W10413645A or FILTER2

Air Filter:

Order Part #W10311524 or AIR1

Produce Preserver:

Order Part # W10346771A or FRESH1

Water Filter, Air Filter and Produce Preserver Bundle Pack:

Order Part # W10413643BL

17

REFRIGERATOR USE

Opening and Closing Doors

There are two refrigerator compartment doors. The doors can be

opened and closed either separately or together.

There is a vertically-hinged seal on the left refrigerator door.

• When the left side door is opened, the hinged seal

automatically folds inward so that it is out of the way.

• When both doors are closed, the hinged seal automatically

forms a seal between the two doors.

A. Hinged seal

Using the Controls

The controls are located above the external dispenser.

IMPORTANT:

• Depending on your model you may have Style 1 or Style 2

controls. Please follow the instructions specific to your

model.

• Style 1 controls are shown in the following graphics except

where indicated.

The control panel display will turn off automatically and enter

"sleep" mode when the control buttons and dispenser pads

have not been used for 2 minutes or more. Press any control

to reactivate the display screen.

Style 1

Style 2

Viewing and Adjusting Temperature Set Points

For your convenience, your refrigerator and freezer temperature

controls are set to the recommended set points at the factory.

When you first install your refrigerator, make sure the temperature

controls are still set to the recommended set points. The

recommended set points are 37°F (3°C) for the refrigerator and

0°F (-18°C) for the freezer.

IMPORTANT:

• Wait 24 hours before you put food into the refrigerator. If you

add food before the refrigerator has cooled completely, your

food may spoil.

NOTE: Adjusting the set points to a colder than

recommended setting will not cool the compartments any

faster.

If the temperature is too warm or too cold in the refrigerator or

freezer, first check the air vents to be sure they are not

blocked before adjusting the controls.

18

The recommended set points should be correct for normal

household use. The controls are set correctly when milk or

juice is as cold as you like and when ice cream is firm.

NOTE: Areas such as a garage or porch, may experience

hotter or colder temperatures and higher humidity than inside

the home. You may need to adjust the temperature away from

the recommended set points to accommodate for these

conditions.

Wait at least 24 hours between adjustments. Recheck the

temperatures before other adjustments are made.

View Temperature Set Points

1. Press and hold TEMP for 3 seconds to activate Temperature

mode.

2. When Temperature mode is activated, press TEMP to toggle

between Fridge and Freezer. The display will show the

temperature set point of the selected compartment, as

shown.

NOTE: To view temperatures in degrees Celsius, press

OPTIONS. To return the display setting to degrees

Fahrenheit, press OPTIONS again.

Recommended Refrigerator Temperature

Recommended Freezer Temperature

3. Press the adjust UP ARROW to raise the temperature set

point or press the adjust DOWN ARROW to lower the

temperature set point.

4. When you have finished adjusting the refrigerator set point,

press TEMP to change the display to show the freezer set

point. When the zone has been changed, "freezer" appears

on the display screen.

5. Press the adjust UP ARROW to raise the temperature set

point or press the adjust DOWN ARROW to lower the

temperature set point.

6. Press LIGHT to save and confirm the new set points, and to

return to the home screen.

NOTE: To exit Temp mode without saving changes, allow about

60 seconds of inactivity. The temperature mode will turn off

automatically and return to the normal screen.

When adjusting temperature set points,

use the following chart as a guide:

REFRIGERATOR too cold

FREEZER too cold

REFRIGERATOR Setting

1° higher

FREEZER Setting

1° higher

Cooling On/Off

Your refrigerator and freezer will not cool when cooling is

turned off. When cooling is off, "cooling off" will light up on the

display screen.

To turn cooling Off and On:

Style 1 - Press and hold OPTIONS and WATER FILTER, at the

same time, for 3 seconds, as shown.

Style 2 - Press and hold FAST ICE and WATER FILTER, at the

same time, for 3 seconds.

IMPORTANT: To avoid unintentionally changing other settings,

press both buttons at exactly the same time.

Adjust Temperature Set Points

Refrigerator set point range: 33°F to 45°F (0°C to 7°C).

Freezer set point range: -5°F to 5°F (-21 °C to -15°C).

1. Press and hold TEMP for 3 seconds to activate Temperature

mode.

2. When Temperature mode is activated, press TEMP to select

the Refrigerator zone. The display will show the temperature

set point of the selected compartment, as shown.

19

NOTE: REPLACE will remain illuminated if a filter is not

Options installed or installed incorrectly.

Style 1

Toaccess available features, press the OPTIONS button to toggle

through the following choices in a continuous loop:

• Fast Ice - The Fast Ice feature assists with temporary periods

of heavy ice use by increasing ice production over a 24-hour

period. Fast Ice will remain on for 24 hours unless manually

turned off.

NOTES:

• Fast Ice works only if the ice maker is turned on. See "Ice

Maker and Storage Bin."

If increased ice production is desired at all times, change

the freezer set point to a lower setting. Setting the freezer

to a colder temperature may make some foods, such as

ice cream, harder.

SpeedCool - The SpeedCool feature assists with periods of

high refrigerator use, full grocery loads, or temporarily warm

room temperatures. SpeedCool will remain on for 24 hours

unless manually turned off.

NOTE: If you adjust the refrigerator temperature set point,

SpeedCool will turn off.

Fast Ice and Speed Cool - Indicates that both features are

on.

Turn all OFF (default) - All options are off.

Style 2

• Fast Ice - The Fast Ice feature assists with temporary periods

of heavy ice use by increasing ice production over a 24-hour

period. Fast Ice will remain on for 24 hours unless manually

turned off.

• Press the FAST ICE button to activate the Fast Ice

feature.

NOTES:

Fast Ice works only if the ice maker is turned on. See "Ice

Maker and Storage Bin."

If increased ice production is desired at all times, change

the freezer set point to a lower setting. Setting the freezer

to a colder temperature may make some foods, such as

ice cream, harder.

Additional Features

Water Filter Status

Press WATER FILTER to display the percentage of use remaining

in the water filter (from 99% to 1%).

ALSO

The water filter status lights will let you know when to replace the

water filter. See "Water Filtration System."

• ORDER (Yellow) - Order a replacement water filter.

• REPLACE (Red) - Replace the water filter.

Door Ajar Alarm

The Door Ajar alarm lets you know when the refrigerator door or

freezer drawer has been open for 5 minutes or longer and the

cooling is turned on.

The words "Door Ajar" will appear on the control panel display

and the Alarm feature will sound an alert tone. The alert tone will

repeat every 2 minutes. Close the doors and drawer to turn off

the tone. The feature is reset and will reactivate when either door

or drawer is again left open for 5 minutes.

NOTE: To mute the alert tone while keeping the doors open, such

as while cleaning the inside of the refrigerator, press any button

on the control panel. The alert tone will be temporarily turned off,

but the "Door Ajar" icon will still be displayed on the dispenser

control panel.

Power Outage Indicator (on some models)

The Power Outage indicator lets you know if the power supply to

the refrigerator has been off and the freezer temperature has

risen to 18°F (-8°C) or higher.

The words "Power Outage" will appear on the control panel

display and an alert tone will sound three times. "Power Outage"

will continue to blink until you acknowledge the power outage.

• Press any control button to confirm. The Power Outage icon

will disappear, and the control panel will return to the Home

screen.

Disabling Sounds (on some models)

When the control panel is muted, all tones, except alert tones are

disabled.

• To turn Off/On control and dispenser sounds, press and hold

LIGHT and WATER FILTER at the same time for 3 seconds.

Showroom Mode

This mode is used only when the refrigerator is on display in a

retail store. If you unintentionally turn on Showroom mode, the

word "Showroom" will appear on the display. All lights and

controls will function, but the refrigerator will not cool.

To exit Showroom Mode:

Style 1 - Press TEMP and OPTIONS at the same time for

3 seconds

Style 2 - Press TEMP and FAST ICE at the same time for

3 seconds.

2O

La page est en cours de chargement...

Maytag MFT2672AEM10 Le manuel du propriétaire

Maytag MFT2672AEM10 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents