Maytag MSB27C2XAB00 User Instructions

Marque: Maytag

Modèle: MSB27C2XAB00

Catégorie: Frigos

Taper: User Instructions

Ce manuel convient également à

THANK YOU for purchasing this high-quality product. If you should experience a problem not covered in TROUBLESHOOTING,

please visit our website at www.maytag.com for additional information. If you still need assistance, call us at 1-800-688-9900.

In Canada, visit our website at www.maytag.ca or call us at 1-800-807-6777.

You will need your model and serial number, located on the inside wall of the refrigerator compartment.

Para obtener acceso a "lnstrucciones para el usuario del refrigerador" en espa_ol, o para obtener informaci6n adicional acerca de

su producto, visite: www.maytag.com.

Necesitara su nQmerode modelo y de serie, ubicado en el interior del compartimiento del refrigerador.

Table of Contents / Table des mati res

REFRIGERATOR SAFETY ........................................................ 2

Proper Disposal of Your Old Refrigerator .............................. 3

INSTALLATION INSTRUCTIONS ............................................. 3

Unpack the Refrigerator ......................................................... 3

Door Removal, Leveling and Alignment ................................. 4

Handle Installation and Removal ............................................ 6

Location Requirements .......................................................... 7

Electrical Requirements .......................................................... 8

Water Supply Requirements................................................... 8

Connect Water Supply ........................................................... 8

Install Air Filter....................................................................... 10

Install Produce Preserver ..................................................... 10

REFRIGERATOR USE............................................................. 12

Using the Controls ................................................................ 12

Convertible Drawer Temperature Control ............................ 13

Crisper Humidity Control ...................................................... 13

Chilled Door Bin .................................................................... 13

Water and Ice Dispensers .................................................... 14

Ice Maker and Storage Bin ................................................... 15

Water Filtration System ........................................................ 16

REFRIGERATOR CARE .......................................................... 16

Cleaning ................................................................................ 16

Lights .................................................................................... 17

Vacation and Moving Care ................................................... 17

TROUBLESHOOTING ............................................................. 18

Refrigerator Operation .......................................................... 18

Temperature and Moisture ................................................... 19

Ice and Water ........................................................................ 19

ACCESSORIES ........................................................................ 20

WATER FILTER CERTIFICATIONS ....................................... 20

PERFORMANCE DATA SHEET ............................................. 21

WAR RANTY ............................................................................. 22

SECURITE DU REFRIGERATEUR ....................................... 24

Mise au rebut appropriee de votre vieux refrigerateur ......... 25

INSTRUCTIONS D'INSTALLATION ....................................... 25

Deballage du refrigerateur .................................................... 25

Retrait, reglage de I'aplomb et alignement de la porte ........26

Installation et demontage des poignees .............................. 29

Exigences d'emplacement ................................................... 29

Specifications electriques ..................................................... 30

Specifications de I'alimentation en eau................................ 30

Raccordement de la canalisation d'eau ............................... 31

Installation du filtre a air........................................................ 32

Installer le sachet de conservation pour produits frais ........33

UTILISATION DU RI_FRIGI_RATEUR .................................... 34

Utilisation des commandes .................................................. 34

Commande de temperature dans le tiroir convertible ......... 36

Reglage de I'humidite dans le bac &legumes .................... 36

Compartiment fraicheur dans la porte ................................. 36

Distributeurs d'eau et de glagons ......................................... 37

Machine &glagons et bac d'entreposage ............................ 38

Systeme de filtration de I'eau ............................................... 39

ENTRETIEN DU REFRIGERATEUR ....................................... 39

Nettoyage .............................................................................. 39

Lainpes ................................................................................. 40

Entretien avant les vacances ou

Iors d'un demenagement ...................................................... 40

DI_PANNAGE ........................................................................... 41

Fonctionnement du refrigerateur .......................................... 41

Temperature et humidite ...................................................... 42

Glagons et eau...................................................................... 42

ACCESSOIR ES........................................................................ 44

FEUlLLE DE DONNEES SUR LA PERFORMANCE .............. 45

GARANTIE ............................................................................... 46

W10493118A

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

[] Plug into a grounded 3 prong outlet.

[] Do not remove ground prong.

[] Do not use an adapter.

[] Do not use an extension cord.

[] Disconnect power before servicing.

[] Replace all parts and panels before operating.

[] Remove doors from your old refrigerator.

[] Use nonflammable cleaner.

[] Keep flammable materials and vapors, such as gasoline,

away from refrigerator.

[] Use two or more people to move and install refrigerator.

[] Disconnect power before installing ice maker (on ice maker

kit ready models only).

[] Use a sturdy glass when dispensing ice (on some models).

[] Do not hit the refrigerator glass doors (on some models).

SAVE THESE INSTRUCTIONS

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other

reproductive harm.

Proper Disposal of

Your Old Refrigerator

Suffocation Hazard

Remove doors from your old refrigerator.

Failure to do so can result in death or brain damage.

Before You Throw Away Your Old Refrigerator or Freezer:

• Takeoff the doors.

• Leave the shelves in place so that children may not easily

climb inside.

IMPORTANT: Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are still

dangerous, even if they will sit for "just a few days." If you are

getting rid of your old refrigerator, please follow these instructions

to help prevent accidents.

important information to know about disposal of

refrigerants:

Dispose of refrigerator in accordance with Federal and Local

regulations. Refrigerants must be evacuated by a licensed,

EPA certified refrigerant technician in accordance with

established procedures.

INSTALLATION INSTRUCTIONS

_ _ _h_ e ¸__ .....

Excessive Weight Hazard

Use two or more people to move and install

refrigerator.

Failure to do so can result in back or other injury.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator for

cleaning or service, be sure to cover the floor with

cardboard or hardboard to avoid floor damage. Always pull

the refrigerator straight out when moving it. Do not wiggle or

"walk" the refrigerator when trying to move it, as floor

damage could occur.

Remove packaging materials. Do not use sharp instruments,

rubbing alcohol, flammable fluids, or abrasive cleaners to remove

tape or glue. These products can damage the surface of your

refrigerator. For more information, see "Refrigerator Safety."

important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

Tempered glass is designed to shatter into many small,

pebble-size pieces. This is normal. Glass shelves and covers

are heavy. Use both hands when removing them to avoid

dropping.

Dee_ _ Re_ eva _ _eve _}g a_d _ g_i_,_'_'_

Gather the required tools and parts and read all instructions before starting installation. Save these instructions for future reference.

NOTE: Before moving your product into your home, measure the doorway of your home to see whether you need to remove the

refrigerator and freezer doors. If door removal is necessary, see the instructions below.

IMPORTANT: Before you begin, turn the refrigerator control OFF or turn cooling off. Unplug refrigerator or disconnect power. Remove

food, the ice storage bin (on some models), and any adjustable door or utility bins from doors.

TOOLS NEEDED:

Bubble level, Phillips screwdriver, 3_6"hex key, 1/4"hex-head socket wrench, 1/4"and 8/W'open-ended wrenches or adjustable wrench,

internal star drive or 3/8"hex-head socket wrench

Electrical Shock Hazard

Disconnect power before removing doors.

Failure to do so can result in death or electrical shock.

Top Left Hinge

A. Do Not Remove Screws.

Wiring Connection

A B C D E

A. P-clamp

B. Routing Plate

C. Electrical Housing

D. Wiring CJip

E. Grommets

F. Wiring Plugs

Water Dispenser

Tubing Connection

A. Face of Fitting

Door Removal

Base Grille

Top Right Hinge

A. Do Not Remove Screws.

Bottom Hinges

(Left and Right)

Leveling

A. Bottom Hinge

B. Leveler Bracket

C. Leveling Foot

Door Alignment

(Bottom Right Hinge)

Raise

A.Alignment Screw

Remove the Doors

Electrical Shock Hazard

Disconnect power before removing doors.

Failure to do so can result in death or electrical shock.

1. Unplug refrigerator or disconnect power.

2. Open both doors to 90 °. Remove the base grille by removing

the two screws, then pulling out on the outside corners. See

Graphic 1.

NOTE: The doors must only be opened to 90°. If they are

opened all the way, the base grille will not come off.

3. Disconnect the water tubing, located behind the base grille

on the freezer door side. The dispenser tubing runs through

the door hinge, and must be disconnected in order to remove

the door. See Graphic 2.

• Press the colored outer ring against the face of fitting and

pull the water tubing free.

NOTE: Keep the water tubing connector attached to the

tube that runs underneath the freezer. The door cannot be

removed if the connector is still attached to the tube that

runs through the door hinge.

4. Disconnect the wiring, located behind the base grille on the

freezer door side. See Graphic 3.

• Remove the P-clamp using a 1/4"hex-head socket

wrench. Remove the small wiring bundle from the

P-clamp.

Remove the wiring clip using a 1/4"hex-head socket

wrench.

Pull the electrical housing out from under the refrigerator.

Disconnect the wiring plugs from the housing.

Gently pull the large wiring bundle (with two white plugs)

through the routing plate.

Close both doors and keep them closed until you are ready to

lift them free from the cabinet.

Use a 3/16"hex key to remove the top left hinge screws as

shown. See Graphic 4.

IMPORTANT: Do not remove either screw A.

Excessive Weight Hazard

Use two or more people to lift the freezer door.

Failure to do so can result in back or other injury.

7. Lift freezer door straight up off bottom hinge. See Graphic 5.

The water tubing and wiring remain attached to the freezer

door and pull through the bottom left hinge.

10.

NOTE: This may require two people - one to lift the door and

another to feed the water tubing and wiring through the

hinge. Be sure the hole in the hinge is clear of obstructions,

then gently pull one water tube through the hinge. (Avoid

kinking the tube.) Next, gently pull the other water tube

through the hinge, again avoiding kinks. Finally, gently pull

the wiring bundle (including the grommet and wiring plugs)

through the hinge.

IMPORTANT: Rest the door on its side on a soft, clean

surface, such as a towel, blanket or piece of cardboard. This

will help avoid damaging the door, water tubing and wiring.

Use a 3Ae"hex key to remove the top right hinge screws as

shown. See Graphic 6.

IMPORTANT: Do not remove either screw A.

Lift the refrigerator door straight up off bottom hinge.

IMPORTANT: Rest the door on its side on a soft, clean

surface, such as a towel, blanket or piece of cardboard. This

will help avoid damaging the door.

It may not be necessary to remove the bottom hinges to

move the refrigerator through a doorway. Both bottom hinges

have similar construction.

• If necessary, use an internal star drive or a 3/8"hex-head

socket wrench to remove the bottom hinges. See

Graphic 7.

IMPORTANT: The leveler brackets are mounted behind

the hinges. If you remove the hinges, make sure that the

leveler brackets are replaced when reinstalling the hinges.

Replace the Doors and Hinges

1. Replace both bottom hinges, if removed. Make sure that the

leveler brackets are assembled behind the hinges. Tighten

screws.

IMPORTANT: When the screws are tightened properly, there

should not be any gaps between the refrigerator, leveler

bracket and hinge.

NOTE: There are two wiring bundles that run underneath the

freezer - a large bundle with a large grommet and two white plugs

at the end, and a small bundle with a small grommet and one

yellow plug at the end.

Excessive Weight Hazard

Use two or more people to lift the freezer door.

Failure to do so can result in back or other injury.

2. Before replacing the freezer door on the bottom left hinge,

feed the small wiring bundle through the hinge. Assistance

may be needed.

IMPORTANT: Do not feed the large wiring bundle through the

hinge. This bundle is intended to run directly from the door to

the connections beneath the freezer. Forcing the large bundle

through the hinge may damage the door and/or the wiring,

and will keep the door from closing properly.

3. Feed both water tubes through the bottom left hinge, then

replace the freezer door on the hinge. Assistance may be

needed.

NOTE: Provide additional support for the doors while the top

hinges are being replaced. Do not depend on the door magnets

to hold the doors in place while you are working.

4. Alignandreplacethetoplefthingeasshown.See Graphic 4.

Tighten screws.

5. Reconnect water tubing and wiring.

IMPORTANT: Do not intertwine the water tubing and wiring

bundles when reconnecting them.

Push the larger 5/le"(7.94 mm) water tube into the blue

fitting until it stops, then push the smaller 1/4"(6.35 mm)

water tube into the green fitting until it stops. See

Graphic 2.

• Reinstall the P-clamp around the small wiring bundle

(with one yellow plug), then replace the P-clamp on the

top screw hole of the routing plate. See Graphic 3.

Gently route the large wiring bundle (with two white plugs)

through the hole in the routing plate, so that the wiring

runs behind the right side of the routing plate. See

Graphic 3.

NOTE: The large wiring bundle should always remain

below the small wiring bundle.

Reconnect the wiring plugs to the electrical housing, then

push the housing back under the refrigerator. Align the left

hole in the front lip of the housing with the right hole in the

refrigerator's base crossbar. See Graphic 3.

Reinstall the wiring clip over the grommets. First install

the smaller grommet into the top of the clip, then install

the larger grommet into the bottom of the clip (closest to

the screw hole). See Graphic 3.

Align the clip's screw hole with the left hole in the

electrical housing and the right hole in the crossbar, and

screw in the clip using a single screw. Tighten screw. See

Graphic 3.

IMPORTANT: Once connected, the wiring bundles should

not be taut. Some flexibility is needed to allow the freezer

door to open properly.

6. Replace the refrigerator door by lifting the door onto the

bottom right hinge.

7. Align and replace the top right hinge as shown. See

Graphic 6. Tighten screws.

8. Replace the ice storage bin (on some models) and any

adjustable door or utility bins.

9. Plug refrigerator into a grounded 3 prong outlet.

Leveling and Door Closing

Your refrigerator has two adjustable front feet -- one on the right

and one on the left. In most cases, the refrigerator should be

steady when both feet are touching the floor. If your refrigerator

seems unsteady or if you want the doors to close more easily,

adjust the refrigerator's tilt using the instructions below:

1. Move the refrigerator into its final location. If necessary, open

both doors to 90° and remove the base grille. See Graphic 1.

2. The two leveling feet are located on the brackets on each

side of the product. See Graphic 8.

NOTE: Having someone push against the top of the refrigerator

takes some weight off the leveling feet. This makes it easier to

make adjustments.

3. Use a 1/4"open-ended or adjustable wrench to adjust the

leveling feet. Turn the leveling foot to the left to raise that side

of the product, or turn it to the right to lower that side of the

product.

4. Open both doors again and check that they close as easily as

you like. If not, tilt the refrigerator slightly more to the rear by

turning the leveling feet to the left. It may take several more

turns, and you should turn both leveling feet the same

amount.

5. Use a bubble level to check the leveling of the refrigerator.

NOTE: Whenever you need to move the refrigerator, turn the

leveling feet to the right until they are no longer touching the

ground. This will allow the refrigerator to roll more easily.

Door Alignment

A refrigerator that is not level from side-to-side may appear to

have doors that are not properly aligned. If the doors appear this

way, use the instructions in the previous section to check the

leveling.

The doors are designed to be slightly different heights when the

refrigerator is empty, in order to account for the weight of food

that will be placed on the doors. If the doors are still not aligned

after checking the leveling and loading the refrigerator with food,

follow the steps below to adjust the door alignment.

1. If necessary, open both doors to 90 ° and remove the base

grille. See Graphic 1.

2. Locate the alignment screw on the bottom hinge of the

refrigerator door. See Graphic 9.

3. Use a 5/le"open-ended or adjustable wrench to turn the

screw. To raise the refrigerator door, turn the screw to the

right. To lower the door, turn the screw to the left.

4. Check that the doors are even at the top. If necessary,

continue to turn the alignment screw until the doors are

aligned.

5. Open both doors to 90°. Replace the base grille. See

Graphic 1.

"t atesa sd Re}< oJa

PARTS INCLUDED: Door handles (2), 1/8"hex key, spare

setscrew(s)

To Install the Handles:

NOTE: The handle mounting setscrews are preinstalled in the

handle.

1. Remove the handles, which are packed inside the refrigerator.

NOTE: To avoid scratching the finish, place the handles on a

towel or other soft surface.

2. Open the freezer door. On the refrigerator door, place the

handle on the shoulder screws with the setscrews facing the

freezer.

A. Shoulder screws

B. Setscrews inside the handle

3. Firmly push the handle toward the door until the handle base

is flush against the door.

4. While holding the handle, insert the short end of the hex key

into the upper hole and slightly rotate the hex key until it is

engaged in the setscrew.

iWliiiii ii!ii ,

5. Using a clockwise motion, tighten the setscrew until it begins

to contact the shoulder screw.

6. Repeat steps 4 and 5 to begin fastening the lower setscrew.

7. Once both setscrews have been partially tightened as

outlined in the previous steps, fully tighten both the upper

and lower setscrews.

IMPORTANT: When the screws feel tight, tighten them an

additional quarter-turn. The handle is not properly installed

without this extra tightening.

8. Open the refrigerator door and close the freezer door. Repeat

steps 2 through 7 to install the other handle onto the freezer

door with the setscrews facing the refrigerator.

9. Save the hex key and all instructions.

To Remove the Handles:

1. While holding the handle, insert the short end of the hex key

into the lower setscrew hole and slightly rotate the hex key

until it is engaged in the setscrew.

2. Using a counterclockwise motion, loosen the setscrew a

quarter-turn at a time.

3. Repeat steps 1 and 2 for the upper setscrew. Gently pull the

handle away from the door.

4. If necessary, use a Phillips screwdriver to remove the

shoulder screws from the door.

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

IMPORTANT: This refrigerator isdesigned for indoor household

use only.

To ensure proper ventilation for your refrigerator, allow for 1/2"

(1.27 cm) of space on each side and at the top. Allow for 1"

(2.54 cm) of space behind the refrigerator. If your refrigerator has

an ice maker, allow extra space at the back for the water line

connections. When installing your refrigerator next to a fixed wall,

leave a 2" (5.08 cm) minimum space on each side (depending on

your model) to allow the doors to swing open.

1/2"(1.27 cm)_

- II -- i

III

2" (5.08crn)/

NOTES:

• This refrigerator is intended for use in a location where the

temperature ranges from a minimum of 55°F (13°C) to a

maximum of 110°F (43°C). The preferred room temperature

range for optimum performance, which reduces electricity

usage and provides superior cooling, is between 60°F (15°C)

and 90°F (32°C). It is recommended that you do not install the

refrigerator near a heat source, such as an oven or radiator.

• Normal minimum cabinet cut-out width required for product

installation is 36" (91.44 cm). However, if the product is

placed against an extended wall and the ability to remove the

crisper pans is desired, an additional 18" (45.72 cm) of

cabinet width is required, so a total cabinet opening width of

54" (137.16 cm) is recommended.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Before you move your refrigerator into its final location, it is

important to make sure you have the proper electrical

connection.

Recommended Grounding Method

A 115 volt, 60 Hz, AC only, 15- or 20-amp fused, grounded

electrical supply is required. It is recommended that a separate

circuit serving only your refrigerator be provided. Use an outlet

that cannot be turned off by a switch. Do not use an

extension cord.

NOTE: Before performing any type of installation or cleaning, or

removing a light bulb, turn cooling off or turn the control

(Thermostat, Refrigerator or Freezer Control depending on the

model) to OFF, and then disconnect the refrigerator from the

electrical source. When you are finished, reconnect the

refrigerator to the electrical source and turn cooling on or reset

the control (Thermostat, Refrigerator or Freezer Control

depending on the model) to the desired setting. See "Using the

Controls."

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

TOOLS NEEDED:

• Flat-blade screwdriver • 1/4"Nut driver

• 7/le"and 1/2"Open-end or two • 1/4"Drill bit

adjustable wrenches • Cordless drill

NOTE: Your refrigerator dealer has a kit available with a 1/4"

(6.35 mm) saddle-type shutoff valve, a union, and copper tubing.

Before purchasing, make sure a saddle-type valve complies with

your local plumbing codes. Do not use a piercing-type or 34e"

(4.76 mm) saddle valve which reduces water flow and clogs more

easily.

IMPORTANT:

• All installations must meet local plumbing code requirements.

• Use copper tubing and check for leaks. Install copper tubing

only in areas where the household temperatures will remain

above freezing.

Water Pressure

A cold water supply with water pressure of between 30 and

120 psi (207 and 827 kPa) is required to operate the water

dispenser and ice maker. If you have questions about your water

pressure, call a licensed, qualified plumber.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the

refrigerator needs to be between 30 and 120 psi (207 and

827 kPa).

If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 to 414 kPa):

• Check to see whether the sediment filter in the reverse

osmosis system is blocked. Replace the filter if necessary.

• Allow the storage tank on the reverse osmosis system to refill

after heavy usage.

• If your refrigerator has a water filter, it may further reduce the

water pressure when used in conjunction with a reverse

osmosis system. Remove the water filter. See "Water

Filtration System."

If you have questions about your water pressure, call a licensed,

qualified plumber.

Read all directions before you begin.

IM PORTANI"."

• Plumbing shall be installed in accordance with the

International Plumbing Code and any local codes and

ordinances.

• Use copper tubing or Whirlpool supply line, Part Number

8212547RP, and check for leaks.

• Install tubing only in areas where temperatures will remain

above freezing.

TOOLS NEEDED:

Gather the required tools and parts before starting installation.

• Flat-blade screwdriver

• 7/le"and 1/2"open-end wrenches or two adjustable wrenches

• 1/4"nut driver

Connect to Water Line

IMPORTANT: Ifyou turn the refrigerator on before the water line

is connected, turn the ice maker OFE

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water.

3. Use a quarter-turn shutoff valve or the equivalent, served by a

1/2"copper household supply line.

NOTE: To allow sufficient water flow to the refrigerator, a

minimum 1/2"size copper household supply line is

recommended.

i/ll

A. Bulb

B. Nut

C. Copper tubing (to refrigerator)

D. Household supply line (7/2"minimum)

Now you are ready to connect the copper tubing to the

shutoff valve. Use 1/4"(6.35 mm) OD soft copper tubing to

connect the shutoff valve and the refrigerator.

• Ensure that you have the proper length needed for the

job. Be sure both ends of the copper tubing are cut

square.

Slip compression sleeve and compression nut onto

copper tubing as shown. Insert end of tubing into outlet

end squarely as far as it will go. Screw compression nut

onto outlet end with adjustable wrench. Do not

overtighten.

C. Copper tubingA. Compression sleeve

B. Compression nut

Place the free end of the tubing into a container or sink, and

turn on main water supply to flush out tubing until water is

clear. Turn off shutoff valve on the water pipe.

NOTE: Always drain the water line before making the final

connection to the inlet of the water valve, to avoid possible

water valve malfunction.

Bend the copper tubing to meet the water line inlet, which is

located on the back of the refrigerator cabinet as shown.

Leave a coil of copper tubing to allow the refrigerator to be

pulled out of the cabinet or away from the wall for service.

Connect to Refrigerator

Style 1

1. Unplug refrigerator or disconnect power.

2. Remove and discard the short, black plastic part from the

end of the water line inlet.

3. Thread the nut onto the end of the tubing. Tighten the nut by

hand. Then tighten it with a wrench two more turns. Do not

overtighten.

NOTE: To avoid rattling, be sure the copper tubing does not

touch the cabinet's side wall or other parts inside the cabinet.

4. Install the water supply tube clamp around the water supply

line to reduce strain on the coupling.

5. Turn shutoff valve ON.

6. Check for leaks. Tighten any connections (including

connections at the valve) or nuts that leak.

Style 2

1. Unplug refrigerator or disconnect power.

2. Remove and discard the plastic part that is attached to the

inlet of the water valve.

3. Attach the copper tube to the valve inlet using a compression

nut and sleeve as shown. Tighten the compression nut. Do

not overtighten.

4. Use the tube clamp on the back of the refrigerator to secure

the tubing to the refrigerator as shown. This will help avoid

damage to the tubing when the refrigerator is pushed back

against the wall.

5. Turn shutoff valve ON.

6. Check for leaks. Tighten any connections (including

connections at the valve) or nuts that leak.

A. Tube clamp

B. Tube clamp screw

C. Copper tubing

_' A

iii..... c

_ii D

D.Compression nut

E.Valveinlet

On some models, the ice maker is equipped with a built-in

water strainer. Ifyour water conditions require a second water

strainer, install it in the 1/4"(6.35 mm) water line at either tube

connection. Obtain a water strainer from your nearest

appliance dealer.

Style 3

1. Unplug refrigerator or disconnect power.

2. Remove and discard the black nylon plug from the gray water

tube on the rear of the refrigerator.

3. If the gray water tube supplied with the refrigerator is not long

enough, a 1/4"x 1/4"(6.35 mm x 6.35 mm) coupling is needed

in order to connect the water tubing to an existing household

water line. Thread the provided nut onto the coupling on the

end of the copper tubing.

NOTE: Tighten the nut by hand. Then tighten it with a wrench

two more turns. Do not overtighten.

A B C D E F G

A B C D

A. Line to refrigerator C. Ferrule (purchased)

B. Nut (purchased) D. Suppfied line from refrigerator

A. Refrigerator water tubing

B. Nut (provided)

C. Bulb

D. Coupling (purchased)

E.Ferrule (purchased)

F Nut (purchased)

G. Household water fine

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any nuts or connections (including

connections at the valve) that leak.

Complete the Installation

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

3. Snap the filter into place.

4. Close the vented door.

Installing the Filter Status Indicator (on some models)

The filter comes with a status indicator, which should be

activated and installed at the same time the air filter is installed.

1. Plug into a grounded 3 prong outlet.

2. Flush the water system. See "Prepare the Water System" or

"Water and Ice Dispensers."

NOTE: Allow 24 hours to produce the first batch of ice. Allow

3 days to completely fill ice container.

On some models, your refrigerator's accessory packet includes

an air filter, which must be installed prior to use. On some

models, the air filter is already installed at the factory.

The air filter reduces the buildup of odors. This helps to maintain

a cleaner environment inside the refrigerator.

Installing the Air Filter (on some models)

The filter should be installed behind the vented door, which is

located (depending on your model) along either the rear or left

interior wall near the top of the refrigerator compartment.

i ¢m

1. Remove the air filter from its packaging.

2. Lift open the vented door.

Place the indicator face-down on a firm, flat surface.

Apply pressure to the bubble on the back of the indicator,

until the bubble pops to activate the indicator.

Lift open the vented air filter door. On some models, there are

notches behind the door.

On models with notches:

• Slide the indicator down into the notches, facing outward.

NOTE: The indicator will not easily slide into the notches

if the rear bubble has not been popped.

• Close the air filter door, and check that the indicator is

visible through the rectangular hole in the door.

On models without notches:

• Store the indicator in a visible place you will easily

remember - either inside the refrigerator, or elsewhere in

your kitchen or home.

Replacing the Air Filter

The disposable air filter should be replaced every 6 months,

when the status indicator has completely changed from white to

red.

To order a replacement air filter, see "Accessories."

1. Remove the old air filter by squeezing in on the side tabs.

2. Remove the old status indicator.

3. Install the new air filter and status indicator using the

instructions in the previous sections.

(on sos® _s_ode s}

On some models, your refrigerator's accessory packet includes a

Produce Preserver, which should be installed prior to use. On

some models, the Produce Preserver is already installed at the

factory.

The Produce Preserver absorbs ethylene, allowing the ripening

process of many produce items to slow down. As a result, certain

produce items will stay fresh longer.

Ethylene production and sensitivity varies depending on the type

of fruit or vegetable. To preserve freshness, it is best to separate

produce with sensitivity to ethylene from fruits that produce

moderate to high amounts of ethylene.

Apples

Asparagus

Berries

Broccoli

Cantaloupe

Carrots

Citrus Fruit

Grapes

Lettuce

Pears

Spinach

Sensitivity to

Ethylene

High

Med.

Low

High

Med.

Low

Med.

Low

High

Ethylene

Production

Very High

Very Low

Low

Very Low

High

Very Low

Very High

Very Low

Installing the Produce Preserver (on some models)

CAUTION: IRRITANT

MAY IRRITATE EYES AND SKIN. DANGEROUS FUMES

FORM WHEN MIXED WITH OTHER PRODUCTS.

Do not mix with cleaning products containing ammonia,

bleach or acids. Do not get in eyes, on skin or clothing. Do

not breathe dust. Keep out of reach of children.

FIRST AID TREATMENT: Contains potassium

permanganate. If swallowed, call a Poison Control Center or

doctor immediately. Do not induce vomiting. If in eyes, rinse

with water for 15 minutes. If on skin, rinse with water.

The Produce Preserver pouches should be installed in their

housing, which is located along an interior side wall of the crisper

or convertible drawer.

NOTE: For best performance, always use two pouches.

1. Remove the Produce Preserver pouches from their

packaging.

FreshF|ow TM

produce preserver

CAUTION ATTENTION

IRRITANT IRRITANT

Read cautions on back, Life les mises en garde au dos

2. Lift up on the housing in order to remove it from its mounting

tab along the wall,

3. Open the housing by pulling up and out on the back of the

top of the housing,

4. Place both pouches inside the housing, then snap the

housing back together,

5. Place the housing back on the mounting tab along the wall,

Installing the Status Indicator (on some models)

The Produce Preserver comes with a status indicator, which

should be activated and installed at the same time the pouch is

installed.

1. Place the indicator face-down on a firm, flat surface.

2. Apply pressure to the bubble on the back of the indicator,

until the bubble pops to activate the indicator.

3. Slide open the cap on the Produce Preserver housing.

4. Place the indicator in the top of the housing, facing outward.

5. Slide the cap closed, and check that the indicator is visible

through the rectangular hole in the cap.

NOTE: The cap will not easily close if the indicator's rear

bubble has not been popped.

Replacing the Produce Preserver (on some models)

The disposable pouches should be replaced every 6 months,

when the status indicator has completely changed from white to

red.

To order replacements, see "Accessories."

1. Remove the old pouches from the Produce Preserver

housing.

2. Remove the old status indicator.

3. Install the new pouches and status indicator using the

instructions in the previous sections.

REFRIGERATOR USE

The refrigerator and freezer controls are located on the dispenser

panel.

IMPORTANT: The display screen on the dispenser control panel

will turn off automatically and enter "sleep" mode when the

control buttons and dispenser pad have not been used for

2 minutes or more. While in "sleep" mode, the first press of a

control button will only reactivate the display screen, without

changing any settings. After reactivation, changes to any settings

can then be made. If no changes are made within 2 minutes, the

display will re-enter "sleep" mode.

• Touch any control button on the dispenser panel to activate

the display screen. The home screen will appear as shown.

To view and adjust the set points, press and hold the TEMP

button for 3 seconds. When adjust mode is activated, adjusting

information will appear on the display screen.

Adjusting the Controls

For your convenience, your refrigerator and freezer controls are

preset at the factory. When you first install your refrigerator, make

sure that the controls are still set to the "mid-settings." The

factory recommended set points are 37°F (3°C) for the

refrigerator and 0°F (-18°C) for the freezer.

IMPORTANT:

• Wait 24 hours before you put food into the refrigerator. If you

add food before the refrigerator has cooled completely, your

food may spoil.

NOTE: Adjusting the set points to a colder than

recommended setting will not cool the compartments any

faster.

• If the temperature is too warm or too cold in the refrigerator or

freezer, first check the air vents to be sure they are not

blocked before adjusting the controls.

• The preset settings should be correct for normal household

usage. The controls are set correctly when milk or juice is as

cold as you like and when ice cream is firm.

• Wait at least 24 hours between adjustments. Recheck the

temperatures before other adjustments are made.

NOTE: To view Celsius temperatures, press the OPTIONS button

when adjust mode is activated. To return the display setting to

Fahrenheit, press OPTIONS again.

• When adjust mode is activated, the display screen shows the

refrigerator set point and "FRIDGE" appears.

• Press the DISPENSE TYPE arrows to raise or lower the set

point.

• When you have finished viewing (and adjusting if desired) the

refrigerator set point, press TEMP to change the display to

show the freezer set point. When the zone has been changed,

"FREEZER" appears on the display screen.

• Press the DISPENSE TYPE arrows to raise or lower the set

point.

• When you have finished viewing (and adjusting if desired)

both the refrigerator and freezer set points, press LIGHT to

save the settings.

NOTE: To exit without saving changes, allow about

60 seconds of inactivity and adjust mode will turn off

automatically.

When adjusting temperature set points, use the following chart as

a guide.

CONDITION: TEMPERATURE

ADJUSTMENT:

REFRIGERATOR too cold REFRIGERATOR Setting

1° higher

REFRIGERATOR too warm REFRIGERATOR Setting

1° lower

FREEZER too cold FREEZER Setting

1° higher

FREEZER too warm / FREEZER Setting

Too little ice 1° lower

The set point range for the refrigerator is 33°F to 45°F (0°C to

7°C). The set point range for the freezer is -5°F to 5°F (-21 °C to

-15°C).

Cooling On/Off

Your refrigerator and freezer will not cool when cooling is

turned off.

• To turn cooling off, press and hold the OPTIONS and FILTER

buttons at the same time for 3 seconds.

IMPORTANT: To avoid unintentionally locking the dispenser

or changing other settings, be sure to press both buttons at

exactly the same time.

When cooling is off, "COOLING OFF" will appear on the

display screen.

Press and hold OPTIONS and FILTER for 3 seconds again to

turn cooling back on.

Additional Features

Fast Ice and SpeedCool

The Fast Ice feature assists with temporary periods of heavy ice

use by increasing ice production over a 24-hour period.

The SpeedCool feature assists with periods of heavy ice usage,

full grocery loads, or temporarily warm room temperatures.

• To turn on the Fast Ice feature, press OPTIONS. "Fast Ice"

will appear on the display screen.

The Fast Ice feature will remain on for 24 hours unless

manually turned off.

• To turn on the SpeedCool feature, press OPTIONS a second

time. The Fast Ice feature will turn off, and the SpeedCool

feature will turn on. "SpeedCool" will appear on the display

screen.

The SpeedCool feature will remain on for 24 hours unless

manually turned off.

To turn on both the Fast Ice and SpeedCool features at the

same time, press OPTIONS a third time. Both "Fast Ice" and

"SpeedCool" will appear on the display screen.

Both features will remain on for 24 hours unless manually

turned off.

• To turn both features off, press OPTIONS a fourth time. Both

"Fast Ice" and "SpeedCool" will disappear from the display

screen.

When Fast Ice and/or SpeedCool are active, the temperature

displays will not change. After 24 hours, the refrigerator returns to

the previous temperature set points.

NOTE: If increased ice production is desired at all times, change

the freezer control to a lower setting. Setting the freezer to a

colder temperature may make some foods, such as ice cream,

harder.

Door Ajar Alarm

The Door Ajar Alarm feature sounds an alarm when the

refrigerator or freezer door is open for 5 minutes and the product

cooling is turned on. The alarm will repeat every 2 minutes. Close

both doors to turn it off. The feature then resets and will

reactivate when either door is left open again for 5 minutes.

NOTE: To mute the audible alarm while keeping the doors open,

such as while cleaning the inside of the refrigerator, press any

button on the control panel. The alarm sound will be temporarily

turned off, but "Door Ajar" will still be displayed on the dispenser

control panel.

Disabling Sounds

• To turn off all control and dispenser sounds, press and hold

LIGHT and FILTER at the same time for 3 seconds.

• Toturn all sounds back on, press and hold LIGHT and FILTER

at the same time for 3 seconds again.

Dual Evaporator (on some models)

Some models come equipped with a dual sequential evaporation

system, which includes two separate evaporators for the

refrigerator and freezer compartments.

Dual evaporation results in higher humidity, which helps keep

foods in the refrigerator from spoiling as quickly and improves

food quality and freshness in the freezer due to decreased freezer

burn. In addition, the dual evaporation system helps keep food

smells in the refrigerator from transferring to ice in the freezer.

NOTE: The dual evaporation system is always activated when

your refrigerator is operating. You do not need to press any

buttons to turn it on.

The control can be adjusted to properly chill meats or vegetables.

The air inside the pan is cooled to avoid "spot" freezing and can

be set to keep meats at the National Livestock and Meat Board

recommended storage temperatures of 28 ° to 32°F (-2° to 0°C).

To store meat:

Set the control to one of the three MEAT settings to store meat at

its optimal storage temperature.

To store vegetables:

Set the control to VEG to store vegetables at their optimal

storage temperatures.

NOTE: If food starts to freeze, move the control to the right (less

cold), toward the VEG setting. Remember to wait 24 hours

between adjustments.

C, ols _,,,I' o

(o_s sosse '_ode/s}

You can control the amount of humidity in the moisture-sealed

crisper. Adjust the control to any setting between LOW and

HIGH.

LOW (open) for best storage of fruits and vegetables with skins.

HIGH (closed) for best storage of fresh, leafy vegetables.

Clsill®d I;¢oo oBiss

Cool air from the freezer is directed to the refrigerator door bin

directly beneath the vents.

NOTE: The dairy compartment and can rack are not associated

with the Chilled Door Bin feature.

Chilled Door Bin Control

The chilled door bin control is located on the left-hand side of the

refrigerator compartment.

A. Chilled door bin control

Slide the door chill control to the left to reduce the flow of

cold air to the bin and make it less cold.

Slide the door chill control to the right to increase the flow of

cold air to the bin and make it colder.

NOTES:

• The dispensing system will not operate when either door

(refrigerator or freezer) is open.

• Allow 24 hours for the refrigerator to cool down and chill

water.

Allow 24 hours to produce the first batch of ice. Discard the

first three batches of ice produced. Wait 72 hours for full ice

production.

The display screen on the dispenser control panel will turn off

automatically and enter "sleep" mode when the control

buttons and dispenser pad have not been used for 2 minutes

or more. While in "sleep" mode, the first press of a control

button will only reactivate the display screen, without

changing any settings. After reactivation, changes to any

settings can then be made. If no changes are made within

2 minutes, the display will re-enter "sleep" mode.

Flush the Water System

Air in the water dispensing system can cause the water dispenser

to drip. After connecting the refrigerator to a water source or

replacing the water filter, flush the water system. Flushing the

water dispensing system forces air from the water line and filter,

and prepares the water filter for use.

NOTE: As air is cleared from the system, water may spurt out of

the dispenser.

1. Using a sturdy container, depress and hold the water

dispenser pad for 5 seconds, then release it for 5 seconds.

2. Repeat Step 1 until water begins to flow.

3. Once water begins to flow, continue depressing and releasing

the dispenser pad (5 seconds on, 5 seconds off) until a total

of 3 gal. (12 L) has been dispensed.

Additional flushing may be required in some households.

The Water Dispenser

IMPORTANT:

• Dispense at least 1 qt (1 L) of water every week to maintain a

fresh supply.

• If the flow of water from the dispenser decreases, it could be

caused by low water pressure.

With the water filter removed, dispense 1 cup (237 mL) of

water. If 1 cup of water is dispensed in 8 seconds or less,

the water pressure to the refrigerator meets the minimum

requirement.

If it takes longer than 8 seconds to dispense 1 cup of

water, the water pressure to the refrigerator is lower than

recommended. See "Water Supply Requirements" or

"Troubleshooting" for suggestions.

To Dispense Water:

1. Press the DISPENSE TYPE arrows on the dispenser control

panel, until "Water" is selected.

2. To dispense water, press a sturdy glass against the dispenser

pad OR press the WATER button.

3. To stop dispensing, remove the glass from the dispenser pad

OR release the WATER button.

The Ice Dispenser

Ice dispenses from the ice maker storage bin in the freezer when

the dispenser pad is pressed. To turn off the ice maker, see "Ice

Maker and Storage Bin."

Your ice maker can produce both crushed and cubed ice. Before

dispensing ice, select which type of ice you prefer by pressing

the DISPENSE TYPE arrows.

The display screen indicates which type of ice is selected.

CRUSHED CUBED

For crushed ice, cubes are crushed before being dispensed. This

may cause a slight delay when dispensing crushed ice. Noise

from the ice crusher is normal, and pieces of ice may vary in size.

When changing from crushed to cubed, a few ounces of crushed

ice will be dispensed along with the first cubes.

To Dispense Ice:

1. Make sure the desired type of ice is selected. To switch

between cubed and crushed, press the DISPENSE TYPE

arrows.

Cut Hazard

Use a sturdy glass when dispensing ice.

Failure to do so can result in cuts.

2. To dispense ice, press a sturdy glass against the dispenser

pad OR press the ICE button. Hold the glass close to the

dispenser opening so ice does not fall outside of the glass.

IMPORTANT: You do not need to apply a lot of pressure to

the pad in order to activate the ice dispenser. Pressing hard

will not make the ice dispense faster or in greater quantities.

3. To stop dispensing, remove the glass from the dispenser pad

OR release the ICE button.

NOTE: Ice may continue to dispense for several seconds

after removing the glass from the pad. The dispenser may

continue to make noise for a few seconds after dispensing.

The Dispenser Light

When you use the dispenser, the light will automatically turn on.

If you want the light to be on continuously, you may choose either

ON or DIM.

ON: Press LIGHT to turn the dispenser light on. "On" will appear

on the display screen.

DIM: Press LIGHT a second time to select DIM mode. "Dim" will

appear on the display screen. The dispenser light will remain on,

but at a lower intensity.

OFF: Press LIGHT a third time to turn the dispenser light off.

The dispenser lights are LEDs that cannot be changed. If it

appears that your dispenser lights are not working, see

"Troubleshooting" for more information.

The Dispenser Lock

The dispenser can be turned off for easy cleaning or to avoid

unintentional dispensing by small children and pets.

NOTE: The lock feature does not shut off power to the

refrigerator, to the ice maker, or to the dispenser light. It simply

deactivates the controls and dispenser pad. To turn off the ice

maker, see "Ice Maker and Storage Bin."

• Press and hold LIGHT for 3 seconds to lock the dispenser.

"Dispenser Locked" will appear on the display screen.

• Press and hold LIGHT a second time to unlock the dispenser.

• Allow 24 hours to produce the first batch of ice. Discard the

first three batches of ice produced.

• The quality of your ice will be only as good as the quality of

the water supplied to your ice maker. Avoid connecting the

ice maker to a softened water supply. Water softener

chemicals (such as salt) can damage parts of the ice maker

and lead to poor quality ice. If a softened water supply cannot

be avoided, make sure the water softener is operating

properly and is well maintained.

• Do not use anything sharp to break up the ice in the storage

bin. This can cause damage to the ice container and the

dispenser mechanism.

• Do not store anything on top of or in the ice maker or storage

bin.

Turning the Ice Maker On/Off:

The On/Off switch can only be accessed when the ice storage bin

has been removed. The switch is located on the freezer door, on

the left side of the wall that surrounds the ice storage bin. See the

following section for bin removal instructions.

• To turn on the ice maker, slide the control to the ON (left)

position.

• To manually turn off the ice maker, slide the control to the

OFF (right) position.

NOTE: The ice maker has an automatic shutoff to keep the

storage bin from overfilling during normal operation. The ice

maker sensors will automatically stop ice production, but the

control will remain in the ON (left) position.

Removing and Replacing Ice Storage Bin:

1. Press down the release lever and tilt the bucket outward. Use

both hands to hold the base of the storage bin, then lift it up

and out.

--..

A. Release lever

NOTE: It is not necessary to turn the ice maker control to the

OFF (right) position when removing the storage bin. The

sensor cover ("flipper door"), located on the right wall of the

freezer door, stops the ice maker from producing ice if the

door is open or the storage bin is removed.

iI I

A. On/Off switch

B. Sensor cover

Replace the bin by sliding it onto the door, then tilting it back

into an upright position. The release lever will click when the

bin is securely in place.

On;;B

Ice Maker Control

Do not use with water that is microbiologically unsafe or

of unknown quality without adequate disinfection before

or after the system. Systems certified for cyst reduction

may be used on disinfected waters that may contain

filterable cysts.

Water Filter Status Light

The water filter status light will help you know when to change

your water filter.

• When the dispenser control panel's water filter status display

changes to "ORDER," this tells you that it is almost time to

change the water filter cartridge.

• Replace the water filter cartridge when the water filter status

display changes to "REPLACE."

If water flow to your water dispenser or ice maker decreases

noticeably, change the filter sooner. The filter should be replaced

at least every 6 months, depending on your water quality and

usage.

• After changing the water filter, reset the status light by

pressing and holding the FILTER button for 3 seconds. When

the system is reset, the "ORDER" and "REPLACE" icons will

disappear from the display screen.

Changing the Water Filter

1. Locate the water filter in the top-right corner of the

refrigerator compartment.

2. Lift open the filter cover door. The filter will be released and

then be ejected as the door is opened.

3. When the door is completely open, pull the filter straight out.

NOTE: There may be some water in the filter. Some spilling

may occur. Use a towel to wipe up any spills.

4. Take the new filter out of its packaging and remove the

covers from the O-rings. Be sure the O-rings are still in place

after the covers are removed.

5. With the arrow pointing up, align the new filter with the filter

housing and slide it into place. The filter cover door will

automatically begin to close as the new filter is inserted.

6. Close the filter cover door completely in order to snap the

filter into place. You may need to press hard.

7. Flush the water system. See "Water and Ice Dispensers."

REFRIGERATOR CARE

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

Both the refrigerator and freezer sections defrost automatically.

However, clean both sections about once a month to avoid

buildup of odors. Wipe up spills immediately.

IMPORTANT: Because air circulates between both sections, any

odors formed in one section will transfer to the other. You must

thoroughly clean both sections to eliminate odors. To avoid odor

transfer and drying out of food, wrap or cover foods tightly.

To Clean Your Refrigerator:

NOTE: Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, flammable fluids, cleaning waxes,

concentrated detergents, bleaches or cleansers containing

petroleum products on plastic parts, interior and door liners or

gaskets. Do not use paper towels, scouring pads, or other harsh

cleaning tools.

1. Unplug refrigerator or disconnect power.

2. Hand wash, rinse, and dry removable parts and interior

surfaces thoroughly. Use a clean sponge or soft cloth and a

mild detergent in warm water.

3. Wash stainless steel and painted metal exteriors with a clean

sponge or soft cloth and a mild detergent in warm water.

4. There is no need for routine condenser cleaning in normal

home operating environments. If the environment is

particularly greasy or dusty, or there is significant pet traffic in

the home, the condenser should be cleaned every 2 to

3 months to ensure maximum efficiency.

If you need to clean the condenser:

• Remove the base grille. See the "Door Removal"

instructions, either in the User Instructions or the separate

instruction sheet provided with your refrigerator.

• Use a vacuum cleaner with asoft brush to clean the grille,

the open areas behind the grille and the front surface area

of the condenser.

• Replace the base grille when finished.

5. Plug in refrigerator or reconnect power.

The interior and dispenser lights are LEDs that cannot be

changed.

• If the dispenser lights do not appear to be working as

described in "Water and Ice Dispensers" or if the interior

lights do not illuminate when either door is opened, call for

assistance or service. See either the front cover or the

Warranty for contact information.

Vacations

If You Choose to Leave Refrigerator On While You Are Away:

1. Use up any perishables and freeze other items.

2. If your refrigerator has an automatic ice maker:

• Raise wire shutoff arm to OFF (up) position or move the

switch to the OFF (right) setting.

• Shut off water supply to the ice maker.

3. Empty the ice bin.

If You Choose to Turn Refrigerator Off Before You Leave:

1. Remove all food from the refrigerator.

2. If your refrigerator has an automatic ice maker:

• Turn off the water supply to the ice maker at least one day

ahead of time.

• When the last load of ice drops, raise the wire shutoff arm

to the OFF (up) position or move the switch to the OFF

(right) setting.

3. Depending on the model, turn the Refrigerator Control to OFF

or turn cooling off. See "Using the Control(s)."

4. Clean refrigerator, wipe it, and dry well.

5. Tape rubber or wood blocks to the tops of both doors to prop

them open far enough for air to get in. This stops odor and

mold from building up.

Moving

When you are moving your refrigerator to a new home, follow

these steps to prepare it for the move.

1. If your refrigerator has an automatic ice maker:

• Turn off the water supply to the ice maker at least one day

ahead of time.

• Disconnect the water line from the back of the

refrigerator.

• When the last load of ice drops, raise the wire shutoff arm

to the OFF (up) position or move the switch to the OFF

(right) setting.

2. Remove all food from the refrigerator and pack all frozen food

in dry ice.

3. Empty the ice bin.

4. Depending on the model, turn the Refrigerator Control to OFF

or turn cooling off. See "Using the Control(s)."

5. Unplug refrigerator.

6. Clean, wipe, and dry thoroughly.

7. Take out all removable parts, wrap them well, and tape them

together so they don't shift and rattle during the move.

8. Depending on the model, raise the front of the refrigerator so

it rolls more easily OR screw in the leveling legs so they don't

scrape the floor. See "Adjust the Doors" or "Door Removal,

Leveling and Alignment."

9. Tape the doors closed and tape the power cord to the back of

the refrigerator.

When you get to your new home, put everything back and refer to

the Installation Instructions for preparation instructions. Also, if

your refrigerator has an automatic ice maker, remember to

reconnect the water supply to the refrigerator.

TROUBLESHOOTING

First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions)

to possibly avoid the cost of a service call.

In the U.S.A., www.maytag.com In Canada, www.maytag.ca

The refrigerator will not operate

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

• Power cord unplugged?Plugintoa grounded 3 prong

outlet.

• Is outlet working? Plug in a lamp to see if the outlet is

working.

• Household fuse blown or circuit breaker tripped? Replace

the fuse or reset the circuit breaker. If the problem continues,

call an electrician.

Are controls on? Make sure the refrigerator controls are on.

See "Using the Controls."

New installation? Allow 24 hours following installation for

the refrigerator to cool completely.

NOTE: Adjusting the temperature controls to coldest setting

will not cool either compartment more quickly.

The motor seems to run too much

Your new refrigerator may run longer than your old one due to its

high-efficiency compressor and fans. The refrigerator may run

even longer if the room is warm, a large food load is added, doors

are opened often, or if the doors have been left open.

The refrigerator seems noisy

Refrigerator noise has been reduced over the years. Due to this

reduction, you may hear intermittent noises from your new

refrigerator that you did not notice from your old model. Below

are listed some normal sounds with an explanation.

• Buzzing - heard when the water valve opens to fill the ice

maker

• Clicking/Snapping - valves opening or closing

• Pulsating - fans/compressor adjusting to optimize

performance

Rattling - flow of refrigerant, water line, or from items placed

on top of the refrigerator

Sizzling/Gurgling - water dripping on the heater during

defrost cycle

Popping - contraction/expansion of inside walls, especially

during initial cool-down

Water running - may be heard when ice melts during the

defrost cycle and water runs into the drain pan

Creaking/Cracking - occurs as ice is being ejected from the

ice maker mold.

The doors will not close completely

• Door blocked open? Move food packages away from door.

• Bin or shelf in the way? Push bin or shelf back in the correct

position.

The doors are difficult to open

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

• Are the gaskets dirty or sticky? Clean gaskets with mild

soap and warm water.

The refrigerator rocks and is not stable

What do I do if the refrigerator rocks and is not stable?

To stabilize the refrigerator, remove the base grille and lower

the leveling feet until they touch the floor. See the "Door

Removal" instructions, either in the User Instructions or the

separate instruction sheet provided with your refrigerator.

The lights do not work

Is a light bulb loose in the socket or burned out? See

"Lights."

Is the dispenser light set to OFF? On some models, the

dispenser light will operate only when a dispenser lever/pad

is pressed. Ifyou want the dispenser light to stay on

continuously, set the dispenser light to ON, or (on some

models) NIGHT LIGHT or AUTO or HALF or DIM. See "Water

and Ice Dispensers."

Is the dispenser light set to NIGHT LIGHT or AUTO? On

some models, if the dispenser is set to the NIGHT LIGHT or

AUTO mode, be sure the dispenser light sensor is not

blocked. See "Water and Ice Dispensers."

e_ _ _/_;_,_ _,

Temperature is too warm

• New installation? Allow 24 hours following installation for

the refrigerator to cool completely.

• Door(s) opened often or left open? Allows warm air to enter

refrigerator. Minimize door openings and keep doors fully

closed.

• Large load of food added? Allow several hours for

refrigerator to return to normal temperature.

• Controls set correctly for the surrounding conditions?

Adjust the controls a setting colder. Check temperature in

24 hours. See "Using the Controls."

There is interior moisture buildup

NOTE: Some moisture buildup is normal. Clean with a dry cloth.

• Humid room? Contributes to moisture buildup.

• Door(s) opened often or left open? Allows humid air to

enter refrigerator. Minimize door openings and keep doors

fully closed.

Zce and Wate

The ice maker is not producing ice or not enough ice

• Refrigerator connected to a water supply and the supply

shutoff valve turned on? Connect refrigerator to water

supply and turn water shutoff valve fully open.

• Kink in the water source line? A kink in the line can reduce

water flow. Straighten the water source line.

• Ice maker turned on? Make sure wire shutoff arm or switch

(depending on model) is in the ON position.

• New installation? Wait 24 hours after ice maker installation

for ice production to begin. Wait 72 hours for full ice

production.

• Large amount of ice recently removed? Allow 24 hours for

ice maker to produce more ice.

• Ice cube jammed in the ice maker ejector arm?

Remove ice from the ejector arm with a plastic utensil. (This

does not apply to models with the ice maker mounted at the

top of the freezer door.)

• Reverse osmosis water filtration system connected to

your cold water supply? This can decrease water pressure.

See "Water Supply Requirements."

The ice cubes are hollow or small

NOTE: This is an indication of low water pressure.

• Water shutoff valve not fully open? Turn the water shutoff

valve fully open.

• Kink in the water source line? A kink in the line can reduce

water flow. Straighten the water source line.

• Reverse osmosis water filtration system connected to

your cold water supply? This can decrease water pressure.

See "Water Supply Requirements."

• Questions remain regarding water pressure? Call a

licensed, qualified plumber.

Off-taste, odor or gray color in the ice

• New plumbing connections? New plumbing connections

can cause discolored or off-flavored ice.

• Ice stored too long? Discard ice. Wash ice bin. Allow

24 hours for ice maker to make new ice.

• Odor transfer from food? Use airtight, moisture-proof

packaging to store food.

• Are there minerals (such as sulfur) in the water? A water

filter may need to be installed to remove the minerals.

• Is there a water filter installed on the refrigerator? Gray or

dark discoloration in ice indicates that the water filtration

system needs additional flushing.

The ice dispenser will not operate properly

• Freezer door closed completely? Close the door firmly. If it

does not close completely, see "The doors will not close

completely." On some models, the refrigerator door must also

be closed in order to operate the dispenser.

• Ice bin installed correctly? Be sure the ice bin is firmly in

position.

• New installation? Wait 24 hours after ice maker installation

for ice production to begin. Wait 72 hours for full ice

production.

• Ice clogged in the ice storage bin or delivery chute?

Remove clogged ice, using a plastic utensil if necessary.

Clean chute and bottom of storage bin using a warm moist

cloth, and dry both thoroughly. To avoid clogging and

maintain a fresh supply of ice, empty the storage bin and

clean both the bin and delivery chute every two weeks.

• Has the wrong ice been added to the bin? Use only cubes

produced by the current ice maker.

• Has the ice melted around the auger (metal spiral} in the

ice bin? Empty the ice container. Use warm water to melt the

ice if necessary.

Cut Hazard

Use a sturdy glass when dispensing ice.

Failure to do so can result in cuts.

• Is the ice dispenser stalling while dispensing "crushed"

ice? Change the ice button from "crushed" to "cubed." If

cubed ice dispenses correctly, depress the button for

"crushed" ice and begin dispensing again.

• Has the dispenser arm been held in too long? Ice will stop

dispensing when the arm is held in too long. Wait 3 minutes

for dispenser motor to reset before using again.

The water dispenser will not operate properly

• Freezer door closed completely? Close the door firmly. If it

does not close completely, see "The doors will not close

completely." On some models, the refrigerator door must also

be closed in order to operate the dispenser.

• Refrigerator connected to a water supply and the supply

shutoff valve turned on? Connect refrigerator to water

supply and turn water shutoff valve fully open.

• Is the water pressure at least 30 psi (207 kPa)? The water

pressure to the home determines the flow from the dispenser.

See "Water Supply Requirements."

Kink in the home water source line? Straighten the water

source line.

• New installation? Flush and fill the water system.

• Water filter installed on the refrigerator? The filter may be

clogged or incorrectly installed.

• Is a reverse osmosis water filtration system connected to

your cold water supply? See "Water Supply Requirements."

Water is leaking from the dispenser

NOTE: One or two drops of water after dispensing is normal.

• Glass not being held under the dispenser long enough?

Hold the glass under the dispenser for 2 to 3 seconds after

releasing the dispenser lever/pad.

• New installation? Flush the water system. See "Prepare the

Water System" or "Water and Ice Dispensers."

• Recently changed water filter? Flush the water system. See

"Prepare the Water System" or "Water and Ice Dispensers."

The dispenser water is not cool enough

(on some models)

NOTE: Water from the dispenser is chilled to only 50°F (10°C).

• New installation? Allow 24 hours after installation for the

water supply to cool completely.

• Recently dispensed large amount of water? Allow

24 hours for water supply to cool completely.

• Water not been recently dispensed? The first glass of water

may not be cool. Discard the first glass of water.

• Refrigerator connected to a cold water pipe? Make sure

the refrigerator is connected to a cold water pipe. See "Water

Supply Requirements."

ACCESSORIES

The following accessories are available for your refrigerator.

To order an accessory, call 1-800-688-9900 and ask for the

appropriate part number listed below or contact your authorized

MAYTAG®Appliances dealer. In Canada, call 1-800-807-6777.

affresh TM*Stainless Steel Cleaner:

Order Part #W10355016

In Canada, order Part #W10355016B

affresh TM*Stainless Steel Wipes:

Order Part #W10355049

In Canada, order Part #W10355049B

affresh TMtKitchen & Appliance Cleaner:

Order Part #W10355010

In Canada, order Part #W10355010B

Water Filter:

Order Part #W10295370 (P4RFWB)

Air Filter:

Order Part #W10311524

Produce Preserver:

Order Part #W10346771

WATER FILTER

CERTIFICATIONS

State of California

Department of Public Health

WaterTreatmentDevice

CertificateNumber

/0- 2030

Date Issued: February 26, 2010

rl'rademarlGModel Dt, signation

P5WB2L

?_'lanulaeturer: Whirlpool _rporatJ_n

Reolacemenl Elements

P4R_FWB

Cyst.,

Organic Con_a_iflants

Atra_lne

2.4-D

Rated Service Capacity: 200 gal Rated Service Flow: 5 gpm

Conditions of Certification:

Do not use where water is microbiologically urlsafe or with water of unknown _uality, except that systems certified

for cyst reduction may be used on disinfected waters fllat may conlain filterable cysls.

1-_ AFFRESH is a trademarl< of Whirlpool, U.S.A.

La page charge ...

Maytag MSB27C2XAB00 User Instructions

Marque: Maytag

Modèle: MSB27C2XAB00

Catégorie: Frigos

Taper: User Instructions

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Maytag MSB27C2XAB00

Maytag MSB27C2XAB00 User Instructions

Ce manuel convient également à

Maytag MSB27C2XAB00 User Instructions

dans d''autres langues

Documents connexes

Autres documents