Hoover F7411900 Mode d'emploi

Catégorie
Aspirateurs
Taper
Mode d'emploi
www.hoover.com
OWNER’S MANUAL
Operating and Servicing Instructions
©2011 Techtronic Floor Care Technology Limited. All rights reserved. #56518217 ID100262-R2
IMPORTANT: READ CAREFULLY BEFORE ASSEMBLY AND USE.
Questions or concerns? For assistance, please call Customer Service at 1-800-944-9200
Mon-Fri 8am-7pm EST. PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE.
THIS PRODUCT IS INTENDED FOR HOUSEHOLD USE ONLY.
IF USED COMMERCIALLY WARRANTY IS VOID.
Español - página E1
2
CONTENTS
Thank you for choosing a HOOVER
®
product.
Please enter the complete model and Manufacturing
Code in the spaces provided.
MODEL
MFG. CODE
Hint: Attach your sales receipt to this owner’s manual.
Verification of date of purchase may be required for
warranty service of your HOOVER
®
product.
Be sure to register your product online at Hoover.com or
call 1-800-944-9200 to register by phone.
1-800-944-9200
Made in China
MANUFACTURING CODE
If you need assistance:
Visit our website at hoover.com. Follow the authorized dealer locator link to find the Hoover
®
authorized
dealer nearest you or call 1-800-944-9200 for an automated referral of Hoover
®
authorized dealer
locations (U.S. only) or to speak with a customer service representative; Mon- Fri 8am- 7pm EST.
PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE.
(Label located on bottom of cleaner)
Important Safeguards .............................................................................................. 3
Cleaner Assembly .................................................................................................... 5
How To Use ............................................................................................................... 7
Cleaner Description .............................................................................................7
The Tanks ............................................................................................................8
How to Clean ............................................................................................................ 10
Tools .......................................................................................................................... 13
Maintenance ..............................................................................................................17
Nozzle ................................................................................................................. 17
Brushes ...............................................................................................................17
Valve.................................................................................................................... 18
Storage ................................................................................................................18
Lubrication ...........................................................................................................18
Troubleshooting ....................................................................................................... 19
Helpful Reminders ...............................................................................................19
Service.......................................................................................................................20
Cleaning Products .................................................................................................... 21
Warranty .................................................................................................................... 22
3
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
When using an electrical appliance, basic precautions should always be
followed,includingthefollowing:
READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE.
WARNING: TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK OR INJURY:
• Toavoidinternalcomponentdamage,useonlyHoover
®
cleaningproductsintended
forusewiththisAppliance.(SeeCleaningProductssectionofthismanual.)
• Useonlyonsurfaces moistenedby thecleaning processor smallspills. Donot
immerse product.
• Connecttoaproperlygroundedoutletonly.See“GroundingInstructions”.
• Donotcleanoverfloorelectricaloutlets.
• Donotusewithouttanksinplace.
• Useextracarewhencleaningonstairs.Donotplacecarpetcleaneronstairs.
• Usecarpetcleaneronlyforitsintendeduseasdescribedintheinstructions.
• UseonlyattachmentsrecommendedbyHoover
®
;othersmaycausehazards.
• Theuseofanextensioncordisnotrecommended.Ifanextensioncordisabsolutely
necessary,useatleasta16gauge3-wirecordwhichhasa3-pronggroundingtype
pluganda3-polereceptaclethatacceptsthemachineplug.
• Unplug carpet cleaner fromoutletwhennot in use. Turn off all controls before
unplugging.
• UnplugbeforeconnectingtheSpinScrub
®
handtool.
• Alwaysdisconnectcordfromelectricaloutletbeforeservicingthecarpetcleaner.
• Donotunplugbypullingoncord.Tounplug,grasptheplug,notthecord.
• Neverhandleplugorappliancewithwethands.
• Donotpullorcarrybycord,usecordasahandle,closedooroncordorpullcord
aroundsharpedgesorcorners.Donotrunapplianceovercord.Keepcordaway
fromheatedsurfaces.
• Donotusewithdamagedcordorplug.Ifapplianceisnotworkingasitshould,
hasbeen dropped,damaged, leftoutdoors, ordropped intowater, takeit toan
AuthorizedHoover
®
WarrantyServiceDealer.
• Closesupervisionisnecessarywhenanyapplianceisusedbyornearchildren.Do
notallowcarpetcleanertobeusedasatoyortorununattendedatanytime.
• Donotpointtoolstowardpeopleorpets.
• Toassistinreducingdryingtime,becertaintheareaiswellventilatedwhenusing
detergentsandothercleanerswiththismachine.
• Keepdetergentsandothercleanersoutofchildren’sreach.
• Donotusetopickupflammableorcombustibleliquidssuchasgasolineorusein
areaswheretheymaybepresent.
• Donotpickupchlorinebleach,draincleaner,gasolineoranyothertoxicmaterial
withthisappliance.
• Donotpickupanythingthatisburningorsmoking,suchascigarettes,matches,or
hotashes.
4
• Avoidpickinguphard,sharpobjectswiththecarpetcleaner.Theymaydamagethe
machine.
• Keephair,looseclothing,fingers,feetandallpartsofbodyawayfromopeningsand
movingparts.
• Useindoorsonly.
• Donotputanyobjectintoopenings.Donotusewithanyopeningblocked;keepfree
ofdust,lint,hair,andanythingthatmayreduceairflow.
• Tohelppreventmattingandresoiling,avoidcontactwithcarpetsuntiltheyaredry.
Keepchildrenandpetsawayfromcarpetsuntiltheyarecompletelydry.
• Storeinadryplace.Donotexposemachinetofreezingtemperatures.
• Donotleaveapplianceunattendedwhenpluggedin.
• DONOTUSETHISEXTRACTORONHARDFLOORSUNLESSYOUHAVETHEPROPER
HARDFLOOR ATTACHMENT.USINGTHIS MACHINEONHARDFLOORS WITHOUT
PROPERATTACHMENTMAYSCRATCHORDAMAGEYOURFLOOR.
GROUNDING
OUTLET BOX
GROUNDING INSTRUCTIONS
Thisappliancemustbegrounded.Ifitshouldmalfunctionorbreakdown,grounding
providesapathofleastresistanceforelectricalcurrenttoreducetheriskofelectric
shock. This appliance is equipped with a cord having an equipment-grounding
conductor(C)andgroundingplug(A).Theplugmustbepluggedintoanappropriate
outlet(B)thatisproperlyinstalledandgroundedinaccordancewithalllocalcodes
and ordinances.
DANGER: Improperconnection oftheequipment-grounding conductorcan
resultintheriskofelectricshock.Checkwithaqualifiedelectricianorserviceperson
ifyouareindoubtastowhethertheoutletisproperlygrounded.Donotmodifytheplug
providedwiththeappliance-ifitwillnotfittheoutlet,haveaproperoutletinstalledby
aqualifiedelectrician.Thisapplianceisforuseonanominal120voltcircuitandhas
agroundingplugthatlooksliketheplug(A)illustratedinsketch(Fig.1).Atemporary
adapter(D)maybeusedtoconnectthisplugtoa2-polereceptacle(E)ifaproperly
groundedoutletisnotavailable(Fig.2).Thetemporaryadaptershouldbeusedonly
untilaproperlygroundedoutlet(B)canbeinstalledbyaqualifiedelectrician(Fig.1).
Thegreencoloredrigidear,lug,orthelike(F)extendingfromtheadaptermustbe
connectedtoapermanentground(G)suchasaproperlygroundedoutletboxcover
(Fig.2).Whenevertheadapterisused,itmustbeheldinplacebyametalscrew.
NOTE:InCanada,theuseofatemporaryadapterisnotpermittedbytheCanadian
Electrical
Code.
F
G
E
D
A
B
C
1
2
1. CLEANER ASSEMBLY
5
A. Cleaner
B. Upper Handle
C. Handle Bolts and Nuts (Three nuts may be in
bag but only two or need for assembly. Bolts and
nuts located in bag with hose)
D. Hose/Cord Hook
E. SpinScrub
®
Brush Assembly
Remove all parts from carton and identify each
item shown.
Make sure all parts are located before disposing of
packing materials.
1.2 Remove tank.
1.3 Position cord protector.
1.4 Slide handle down.
1.5 Insert bolts and attach nuts. Tighten with
screwdriver.
ATTACH HANDLE
CARTON CONTENTS
1.3
1.4
1.5
1.2
1.1
Carpet
Upholstery
Cleaner
Pre-
Cleaner
Bare
floor
cleaner
A
B
C
D
E
H
I
G
F. Hose/Tool Caddy*
G Hose
H Stair/Upholstery Nozzle
I. SpinScrub
®
Hand Tool*
*Available on select models only. Accessories not
included with your model may be purchased
separately by visiting hoover.com.
NOTE: Phillips screwdriver needed for assembly.
F
Cord Protector
-V2
Actual model may vary from images shown.
6
1.6 1.7
REPLACE UPPER TANK
1.6 Position bottom of
tank onto cleaner.
1.7 Push top of tank
and tank handle while
supporting back of
cleaner with other hand.
1.8 Push up on handle
to latch it to cleaner.
Check tank to make
sure it is secure.
1.8
1.9
ATTACH HOSE/CORD HOOK
1.9 Snap hook onto
cleaner.
ATTACH TOOL CADDY
(for storage on cleaner)
(Available on select models only)
1.10 Insert tabs.
1.11 Slide caddy down. Notch (B) rests on hook (C).
1.10
1.11
STORE HOSE
1.12 Start.
1.13 Wrap.
1.14 Finish. Use clips
(D) to secure hose and
solution tube (E and in-
set).
1.12
1.13 1.14
E
D
STORE TOOLS
1.15
IMPORTANT
Tool caddy is removable for storage on wall or
in closet.
1.15 Store Tools on
back side of cleaner as
shown.
C
B
D
E
Actual model may vary from images shown.
2. HOW TO USE
CLEANER DESCRIPTION
1. Hand Grip
2. SolutionTrigger: press to release
cleaning solution
3. ON/OFF Switch
4. Rinse Setting Switch
5. SpinScrub
®
Hand Tool*
6. Carry Handle
7. Clean Water Tank Handle
8. Clean Water Tank
9. Detergent Container
10. Dirty Water Tank Handle
11. Dirty Water Tank
12. Dirty Water Tank Latches
13. SpinScrub
®
Mode Selector
14. Solution Tube Connection Port
15. Edge Cleaners: provided on both
sides of nozzle to remove dirt
near baseboards
16. Nozzle
17. Hose Connection Port
18. Cord Hook: rotates for quick cord
release
19. Hose*
20. Hose/Tool Caddy*
21. Stair/Upholstery Nozzle*
22. Cord/Hose Hook
23. Handle Release Pedal
24. Wheels
Operate cleaner only at voltage specified on data plate on bottom
of cleaner.
This cleaner is intended for household use.
2
4
1
8
11
13
12
5
9
17
14
3
6
7
10
15
16
24
20
21
23
18
19
22
2.1
ON
OFF
WASH
AUTO RINS
E
Rinse
2.2
2.3
ON-OFF SWITCH
HANDLE RELEASE PEDAL
To turn cleaner ON,
push switch down.
To turn cleaner OFF,
push switch up.
Step on pedal (A) to
lower handle to
operating position.
Handle does not lock
into a single position but
“floats” to allow
convenient operation.
A
2.4
TRANSPORTING
To move your cleaner
from room to room, put
handle in upright and
locked position, tilt
cleaner back on wheels
and push forward.
2.5
CARRY HANDLE
The cleaner may also
be lifted by placing a
hand above the upper
clean water tank handle
as shown.
7
Actual model may vary from images shown.
*Accessories not included with your
model may be purchased separately
by visiting www.hoover.com, or your
local HOOVER
®
service center.
CAUTION
! !
DO NOT USE THIS EXTRACTOR ON HARD FLOORS
UNLESS YOU HAVE THE PROPER HARD FLOOR
ATTACHMENT. USING THIS MACHINE ON HARD FLOORS
WITHOUT PROPER ATTACHMENT MAY SCRATCH OR
DAMAGE YOUR FLOOR.
8
SPINSCRUB
®
MODE SELECTOR
Your SteamVac
®
cleaner has two agitator brush
settings.
SPILL PICK-UP - brushes OFF for picking up spills
or cleaning carpets and hard floors when brushing
is not desired.
POWER SCRUB - brushes at maximum speed for
cleaning carpets
Slide setting selector to the desired setting before
cleaning.
THE TANKS:
CLEAN WATER SOLUTION TANK
(upper tank)
2.7 The clean water tank (C) holds the water that
will either be mixed with detergent for cleaning the
carpet or floor, or used to rinse the carpet or floor.
The detergent container (D) is permanently attached
to the water tank. It holds the detergent that mixes
with the water.
2.6
2.7
C
D
Unplug cleaner from electrical outlet.
To remove tank, press down on tank handle and pull
forward.
2.8 Fill tank (E) with hot tap water.
How to Fill
CAUTION
! !
Do not fill with water above 140°F (60°C).
E
2.8
F
2.9
2.9 - 2.10 Fill detergent container (F) with Hoover
®
Carpet/Upholstery Detergent.
Replace container cap and tighten.
2.11 Position bottom of tank onto cleaner using one
hand on each side of the tank to center it on the unit.
2.10
2.11
IMPORTANT
The tank pivots towards the back of the unit.
Push the top of the tank and tank handle while
supporting the back of the unit with your other
hand.
IMPORTANT
Use only HOOVER
®
SteamVac
®
detergents.
They are specially formulated for use with your
SteamVac
®
cleaner. Non-Hoover
®
cleaning
solutions may harm the machine and void the
warranty.
Actual model may vary from images shown.
9
How to Fill (continued)
2.12 Push up on the handle once the tank is
back to latch it to the unit.
Check tank to make sure it is securely latched.
2.13 There may be a small amount of water
(indicated by arrows) on the base when the
tank is removed from the unit. This is a normal
condition.
CAUTION
! !
Detergents contain Anionic and Nonionic
Surfactants. Avoid contact with eyes and
skin. In case of contact with eyes, flush
with cold water for 15 minutes. In case
of contact with skin, wash with water. If
irritation persists, call a physician.
WARNING
! !
Certain oxygenated-type cleaners, such as OxiClean*
and TuffOxi** will damage your SteamVac
®
detergent
container (A), Clean Water Tank (B) or Dirty Water
Tank (C).
Use only HOOVER
®
SteamVac
®
Oxy detergent
for this purpose.
*OxiClean is a registered
trademark of Orange Glo
International, Inc.
**TuffOxi is a trademark of
Tuff Products for Pets.
A
B
C
2.12
2.13
DIRTY WATER TANK
(lower tank)
The Dirty Water Tank holds the dirty solution that is
picked up from the surface being cleaned.
When the Dirty Water Tank is full, the automatic
shut-off will engage, suction will stop and the tank
must be emptied (see Automatic Shut-Off section).
How to Empty
Turn cleaner off and unplug from electrical outlet.
To prevent possible leaking, remove clean water
tank by pressing down on tank handle and pulling
forward; set tank aside (do not set tank on furniture).
2.14 Turn Dirty Water Tank latches (G) outward
(one on each side of tank). Raise handle straight up
and lift tank off cleaner. Carry tank to sink or drain.
2.15 Lower handle toward back of tank to unlock lid.
Lift lid off tank.
Empty tank and reposition lid.
For full suction, it is important that the Dirty Water
Tank lid is properly secured before cleaning.
Raise tank handle to carrying position and place it
onto cleaner. Lower handle to front of tank.
Turn latches (one on each side of tank) inward to
lock tank in place.
2.14 2.15
G
IMPORTANT
Make sure the tank handle is moved forward to
lock the tank lid before putting cleaner in upright
position. Failure to secure properly may result
in damage to the tank handle and may cause
poor suction.
Actual model may vary from images shown.
10
BEFORE YOU BEGIN CLEANING
a. Vacuum thoroughly - For carpet, use a HOOVER
®
vacuum cleaner with an agitator for best results.
Vacuum upholstery with a vacuum cleaner with
cleaning tool attachments. Use a crevice tool to
reach into tufts and folds. Do not use the carpet
cleaner as a dry vacuum cleaner.
b. For upholstery, check cleaning code - Use your
HOOVER
®
carpet cleaner only if the upholstery
fabric is marked with a “W” (for “wet” clean) or “S/W”
(for “solvent/dry” or “wet” clean). Do not clean fabric
marked “S” (“solvent/dry” clean only). If your
upholstery does not have a code, seek professional
assistance.
c. Test for colorfastness - Wet a white absorbent
cloth with the detergent. In a small, hidden area,
gently rub the surface with the dampened cloth.
Wait ten minutes and check for color removal or
bleed with white paper towel or cloth. If surface has
more than one color, check all colors.
d. When cleaning entire floor, move furniture out of
area to be cleaned (may not be necessary if only
high traffic areas are to be cleaned). For furniture
too heavy to move, place aluminum foil or wax
paper under legs. This will prevent wood finishes
from staining carpet. Pin up furniture skirts and
draperies.
e. Pretreat spots and heavy traffic areas with
HOOVER
®
Spot & Stain Spray Cleaner*- Follow
Directions on bottle.
f. To prevent staining, use plastic or aluminum foil to
protect wood or metal surfaces from possible water
spray.
g. To avoid wetting and possible damage to wood
floors underneath area rugs/carpet, either move
area rugs/ carpet to a non-wood hard floor surface
or place waterproof material (e.g. plastic)
underneath them before cleaning.
*Available at additional cost if not included with your
model.
3. HOW TO CLEAN
AUTOMATIC SHUT OFF
When the Dirty Water Tank (lower tank) is full the automatic shut off mechanism
will shut off the cleaner suction (suction will be noticeably reduced).
2.16 At that time, the yellow float disk will rise to the top of the Dirty Water Tank
lid (B). The cleaner will no longer pick up dirty solution and the motor sound will
become noticeably higher in pitch.
When this happens, turn cleaner off and empty Dirty Water Tank before
continuing use.
Check clean water tank also; it may need to be refilled.
Do not use without float and float retainer in place. If broken or dislodged, take
to an Authorized Dealer for repair.
2.16
B
Actual model may vary from images shown.
11
ON
OFF
WASH
AUTO RINSE
Rinse
3.1/3.1a
CLEANING CARPET
Read “Before You Begin Cleaning” instructions
above.
Fill Clean Water Tank according to instructions for
Figs. 2.9.
Fill detergent container with Hoover
®
detergent
according to instructions for Figs. 2.10 and 2.11.
Select proper SpinScrub
®
mode (see pg. 8).
Dry hands and plug cord into a properly grounded
outlet.
Do not clean over floor electrical outlets.
To avoid walking on damp carpet, start at the end of
the room farthest from the door or path to sink
where tanks will be emptied and filled.
Step on handle release pedal and lower handle to
operating position.
3.1 Set Rinse Setting switch to Wash/Rinse. Turn
cleaner ON.
3.2 Squeeze trigger to apply cleaning solution and
slowly push cleaner forward (equals one wet
stroke).
Continue to squeeze trigger and slowly pull cleaner
back toward you (second wet stroke).
IMPORTANT
To assure proper rinsing, it is important to keep
the cleaner on the same path backward as
forward.
3.2
ON
OFF
Rinse
WASH
AUTO RINSE
3.3
IMPORTANT
To avoid saturating carpet, do not use more
than 4 wet strokes over one area. Always end
with dry strokes.
Keep nozzle flat on floor for both forward and
reverse strokes.
3.3 If you would like to rinse the carpet with water
only, set Rinse Setting switch to RINSE. Repeat
cleaning motion. In this setting, rinsing will be done
on both forward and reverse strokes.
For heavily soiled areas, repeat cleaning motion.
Avoid saturating carpet, as noted.
It is best to alternate wet and dry strokes as
described above.
For best cleaning results and to aid in faster drying
of carpet, end with more dry strokes. (Continue
using dry strokes until little water is visible passing
through the Dirty Water Tank lid.)
Empty Dirty Water Tank when the motor sound
becomes higher pitched and there is a loss in
suction (see “Automatic shut-off”, Fig. 2.17).
When finished cleaning, follow “After Cleaning”
instructions on page 13.
Release trigger and slowly push cleaner forward
over area just sprayed with solution (dry stroke).
Then slowly pull cleaner back toward you without
squeezing trigger (dry stroke). Continue using dry
strokes until little water is visible passing through
the Dirty Water Tank lid (Pass over the same area a
minimum of 4 times = 2 while squeezing the trigger
and 2 without).
For best results, use straight, parallel strokes.
Overlap strokes by 1 inch to help prevent streaking.
Actual model may vary from images shown.
3.2a
AUTO
WASH RINSE
FOR MODELS WITH AUTO RINSE FEATURE
(available on select models only)
3.1a Set Rinse Setting switch to Wash/Auto
Rinse. Turn cleaner ON.
3.2a Squeeze trigger to apply cleaning
solution and slowly push cleaner forward
(equals one wet stroke).
Continue to squeeze trigger and slowly pull
cleaner back toward you (second wet stroke).
The cleaner rinses the carpet on the
backward pass.
12
PICKING UP SPILLS
Your HOOVER
®
SteamVac
®
cleaner may also be
used to pick up small liquid spills on carpet or
uholstery.
For best results, pick up spills immediately by
placing the stair/upholstery nozzle just above the
spill and suction up any residue on top of the carpet.
If the spill remains, place either the stair/ upholstery
nozzle or floor nozzle with the SpinScrub
®
mode
selector to SPILL PICK-UP in front of the spill, pull
the nozzle very slowly over the spill initially with
suction only. Repeat with spray and suction.
If a spot is left, the stair/upholstery nozzle is
generally more effective for removing it. Although no
cleaning solution can completely remove all spots,
they can be treated by following the instructions
provided by the manufacturer of the carpet,
upholstery, or hard floor surface being cleaned.
Do not use the SteamVac
®
cleaner to pick up
flammable or combustible liquids or chemicals.
When finished, follow “After Cleaning” instructions.
AFTER CLEANING
Allow carpet or upholstery to dry. To help prevent
matting and resoiling the carpet, keep children and
pets away from surface until it is completely dry. If it
is necessary to walk on damp carpet, place towels
or white cloths on the traffic areas.
If furniture must be replaced before the carpet is dry,
place plastic or aluminum foil under legs of furniture
so metal slides or wood finishes will not stain the
carpet.
Empty tanks, rinse with clean water and let air dry.
Rinse the Dirty Water Tank lid and let air dry.
3.4 Remove lint from filter screen located inside
Dirty Water Tank.
3.5 Remove lint from filter screen located on bottom
of cleaner.
3.4 3.5
IMPORTANT
When brushes seem to be rotating slowly,
disconnect cleaner from electical outlet and
check and clean this screen.
Actual model may vary from images shown.
13
ATTACH HOSE
4. TOOLS
CAUTION
! !
To reduce the risk of injury from moving parts,
unplug cleaner.
How to Attach
4.1 Open hose connection port (A).
Insert short hose end, matching tabs on hose with
same-sized slots in connection port.
Push hose into port and lock in place.
4.2 Plug solution tube firmly into solution connection
port (B).
How to Remove
4.2 Squeeze latches (C) on top and bottom of hose.
Remove hose from port. Close door.
Remove solution tube from solution connection port.
4.1
A
4.2
C
B
TOOLS
A. SpinScrub
®
Hand Tool (Available on select
models only) has rotating brushes for extra
scrubbing action on small carpet areas, carpeted
stairs and upholstery. For some models, the brushes
can be removed for converting to the scrub module.
(Available on select models only)
B. Stair/Upholstery Nozzle has a built-in brush to
help provide the scrubbing action some spots may
need for removal.
A
B
4.3
SPINSCRUB
®
HAND TOOL
(Available on select models only)
4.4 To remove the SpinScrub
®
hand tool pull tool
down and outward.
To reposition the tool, reverse this procedure.
How to Reattach Tool Cover
4.5 The tool cover is designed with a break-away
feature which allows it to snap free if it is pushed
open too far.
To reattach, align hinges of cover with holes on
sides of tool storage area. Snap door into place.
4.4 4.5
Actual model may vary from images shown.
14
G
H
How to Attach Tools
Place handle in upright position and remove hose
from rack.
All tools attach to the hose in the same manner:
4.6 Connect tool to hose by sliding it onto connector
until the tab (G) locks it securely.
Using your thumb, push forward and up on the latch
(H) to remove tool.
4.6
After Using Tool
Drain suction hose by turning cleaner ON and
holding nozzle up for several minutes. Do not press
trigger.
CAUTION
! !
To reduce the risk of injury from moving parts,
unplug cleaner.
4.7 4.8
Disconnect hose and solution tube from cleaner.
4.7 Drain solution tube by placing round end in
sink and raising nozzle above your head. Press
the trigger.
4.8 The tool caddy can be removed and hung on
a coat hanger for storage or placed back on the
cleaner.
CAUTION
! !
To reduce the risk of injury from moving parts,
unplug cleaner.
Actual model may vary from images shown.
15
Read “Before You Begin Cleaning” instructions on
page 10.
Attach hose and solution tube as instructed in Figs.
4.1 and 4.2.
Place handle in upright position. Agitator brushes
will not rotate while handle is in upright position.
Fill clean water tank according to instructions for
Figs. 2.9 to 2.11.
Fill detergent container with HOOVER
®
detergent
according to instructions for Fig. 2.11.
Attach tool to end of hose.
Hose length may require that machine be placed at
the top of the stairs to clean upper half of stairway
and at bottom of stairs to clean lower half.
CLEANING CARPETED STAIRS
A
B
4.9
4.10
WARNING
! !
To prevent machine from falling, use extra
caution when cleaning on stairs.
Do not place cleaner on stairs.
Do not point tools toward people or pets.
Dry hands and plug cleaner into a properly grounded
outlet.
Set Rinse Setting switch to WASH. Turn cleaner
ON.
4.9 Pre-spray the carpeted stair by holding the tool
(A) or (B) about one inch above the carpet and push
it forward while pressing the trigger (equals one wet
stroke).
Position tool against the riser and slightly press it
into carpet pile. Press the trigger and pull the tool
slowly over the carpet (second wet stroke). Release
trigger at end of stroke.
4.10 Lift tool, and position it against riser. Pull tool
slowly over carpet without pressing trigger (dry
stroke).
Overlap strokes by 1/2 inch to help prevent
streaking.
It is best to alternate wet and dry strokes as
described above. End with more dry strokes to aid
in faster drying of carpet.
To avoid saturating carpet, do not use more than
4 wet strokes over any one area. Always end with
dry strokes.
If additional cleaning is necessary, wait until the
carpet is completely dry before using the tool again.
Empty Dirty Water Tank when the motor sound
becomes higher pitched and there is a loss in suction
(see “Automatic Shut-Off”, Fig. 2.17).
When finished cleaning, follow “After Cleaning”
instructions on page 12 and “After Using Tool”
instructions on page 14.
Actual model may vary from images shown.
16
CLEANING UPHOLSTERY
Read “Before You Begin Cleaning” instructions on
page 10.
Be sure to check the cleaning code on your
upholstery. Use your cleaner only on upholstery
marked “W” or “W/S”.
Attach hose and solution tube as instructed in Figs.
4.1 to 4.2.
Place handle in upright position. Agitator brushes
will not rotate while handle is in upright position.
Fill Clean Water Tank according to instructions for
Figs. 2.9 to 2.11.
Fill detergent container with HOOVER
®
detergent
according to instructions for Fig. 2.10. Do not
use hard floor cleaning solution when cleaning
upholstery.
Attach tool to end of hose.
Do not point tools toward people or pets.
Dry hands and plug cleaner into a properly grounded
outlet.
4.11
4.12
IMPORTANT
RINSE is not available during tool use. The hose
will only dispense water mixed with detergent.
Set Rinse Setting switch to WASH. Turn cleaner
ON.
4.11 Gently press the tool onto the fabric. Press the
trigger and slowly pull the nozzle over the fabric.
Overlap strokes by 1/2 inch to help prevent
streaking.
Make additional strokes without pressing the trigger
to remove more moisture.
To clean in corners or creases, lift the tool one half
inch from the fabric and press the solution trigger.
Vacuum up the solution with the tool without
pressing the trigger.
4.12 For heavily soiled areas, it may be necessary
to repeat the cleaning process. Make crisscrossing
strokes to the original pattern; overlap each pass.
Make no more than 2 passes with the solution over
any one area to prevent over-wetting and damage
to fabric.
If additional cleaning is necessary, wait until the
upholstery is completely dry before using the tool
again.
Empty Dirty Water Tank when the motor sound
becomes higher pitched and there is a loss in
suction (see “Automatic Shut-Off”, Fig. 2.17).
When finished cleaning, follow “After Cleaning”
instructions on page 12 and “After Using Tool”
instructions on page 14.
Actual model may vary from images shown.
17
If lint or other debris becomes lodged in nozzle, it
can be removed for cleaning.
NOZZLE: How to Clean
CAUTION
! !
To reduce the risk of injury from moving parts,
unplug cleaner before servicing.
Remove both tanks as described in Fig. 2.16. With
handle in upright position, tilt cleaner back so that
handle rests on the floor.
5.1 Lift up rear edge of nozzle. Slide nozzle up and
remove from cleaner.
5.2 To replace nozzle, line up tabs (A) on nozzle
with holes (B) in cleaner. Slide tabs into holes.
5.1
5.2
B
A
BRUSHES: How to Change and Clean
Your cleaner is equipped with removable brushes.
Follow these directions for changing brush
assemblies or for easy cleaning.
How to Remove
To prevent possible leaking, remove Clean Water
Tank and Dirty Water Tank. Set tanks aside.
With handle in upright position, tilt cleaner back until
handle rests on the floor.
5.3 Grab brush assembly and pull firmly.
The brushes can be cleaned under running water.
CAUTION
! !
To reduce the risk of injury from moving parts,
unplug cleaner before servicing.
Slide nozzle completely onto cleaner. Press down
on nozzle to secure it.
Replace Dirty Water Tank (Fig. 2.16).
The nozzle must be in the proper position in order
for the Dirty Water Tank to go on properly.
5.3
5. MAINTENANCE
Familiarize yourself with these home maintenance tasks as proper use and care of your cleaner will ensure
continued cleaning effectiveness.
Any other servicing should be done by an authorized service representative.
How to Replace
5.4 Align posts (A) on both ends of brush assembly
with slots (B) in cleaner housing.
Make sure that the square post (C) also aligns with
the square hole (D). Turn brushes slightly until post
fits easily into hole.
Press brush assembly firmly to snap into place.
A
A
B
B
C
D
5.4
Actual model may vary from images shown.
18
LUBRICATION
The motor is equipped with bearings that contain
sufficient lubrication for the life of the motor.
The addition of lubricant could cause damage.
Therefore, do not add lubricant to motor
bearings.
STORAGE
Before storing:
Empty Clean Water Tank and let air dry.
Replace on cleaner.
Empty Dirty Water Tank, rinse tank and lid
thoroughly with clean water and let air dry.
Allow brushes and underside of carpet cleaner
to air dry thoroughly before storing carpet
cleaner on a carpeted or wood surface.
A
A
B
C
5.7
5.6
5.5
Remove Clean Water
Tank.
5.5-5.6 Turn valve cap
(A) counter clockwise
and remove.
Soak valve cap in warm
water for at least 15
minutes. Wipe cap dry.
5.7 Align slots (B) on
cap with tabs (C) in
opening.
Turn cap clockwise to
tighten.
VALVE:
How to Unclog
Actual model may vary from images shown.
19
6. TROUBLESHOOTING
If a minor problem occurs, it usually can be solved quite easily when the cause is found by using the
checklist below.
Any other servicing should be done by an authorized service representative.
WARNING
! !
To reduce risk of personal injury - unplug cleaner before servicing.
PROBLEM POSSIBLE CAUSE
POSSIBLE SOLUTION
Cleaner won’t run.
1. Not firmly plugged in.
1. Plug unit in firmly.
2. No voltage in wall plug.
2. Check fuse or breaker in home.
3. Blown fuse or tripped
breaker.
3. Replace fuse or reset breaker in home.
Low suction. 1. Dirty Water Tank full/
automatic shut off engaged.
1.Remove and empty Dirty Water Tank. Clean
filter screen.
2. Blockage In tool on end of
hose.
2. Remove tool and clear blockage.
3. Dirty Water Tank lid not on
correctly.
3. Make sure lid is on securely.
4. Clean Water Tank empty, but
detergent remains.
4. Fill Clean Water Tank
Clean water won’t
dispense.
1. Clean Water Tank not firmly
in place.
1. Make sure tank is securely locked in
position.
2. Clean Water Tank or
detergent container empty.
2. Refill container according to instructions for
surface being cleaned.
3. Dirty Water Tank lid not on
correctly.
3 .Make sure lid is firmly in place.
Detergent won’t
dispense
1. Valve cap clogged. 1. Remove and clean valve cap
(see instructions below).
Brushes/brush
indicator won’t
rotate during floor
cleaning.
1. Dirty filter screen on bottom
of unit.
1. Clean screen.
HELPFUL REMINDERS
Use HOOVER
®
brand detergents; others may
foam too much or cause leaking.
Use extra dry strokes to aid in faster drying of the
carpet.
6.1 Fill tank (A) with hot (under 140˚F /60˚C) tap
water ONLY. Do not put any detergent in water
tank. Fill detergent container (B) with HOOVER
®
detergent.
6.2 Secure Dirty Water Tank lid before cleaning.
• Empty Dirty Water Tank when full or when
automatic shut-off engages.
6.1
B
A
6.2
CAUTION
! !
Unplug the cleaner before doing any of the
following.
Actual model may vary from images shown.
20
To obtain approved Hoover
®
service and genuine Hoover
®
parts, locate the nearest Authorized Hoover
®
Warranty Service Dealer (Depot) by:
Checking the Yellow Pages under “Vacuum Cleaners” or “Household”.
Visit our website at hoover.com (U.S. Customers) or hoover.ca (Canadian customers).
Follow the service center link to find the service outlet nearest you.
For an automated referral of authorized service outlet locations call 1-800-944-9200.
Do not send your vacuum to Hoover
®
, Inc., Company in Glenwillow for service. This will only result in delay.
If you need further assistance:
To speak with a customer service representative call 1-800-944-9200; Mon-Fri 8am-7pm EST. In Canada,
contact Hoover
®
Canada, Toronto: 755 Progress Ave., Scarborough, ON M1H 2W7 OR Hoover
®
Canada,
Edmonton: 18129-111 Ave., Edmonton, AB T5W 2P2, Phone: 1-800-944-9200, Mon-Fri 8am-7pm EST.
Always identify your vacuum by the complete model number when requesting information or ordering parts.
(The model number appears on the bottom of the vacuum.)
PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE.
7. SERVICE
1 / 1

Hoover F7411900 Mode d'emploi

Catégorie
Aspirateurs
Taper
Mode d'emploi

dans d''autres langues