KitchenAid KGRS807SBL02 Guide d'installation

Marque: KitchenAid

Modèle: KGRS807SBL02

Catégorie: Cuisinières

Taper: Guide d'installation

Kitchen_kid _

INSTALLATION INSTRUCTIONS

30" (76.2 CM) FREESTANDING AND SLIDE-IN

GAS RANGES

INSTRUCTIONS D'INSTALLATION DES

CUISINIERES A GAZ AUTOPORTANTES ET

ENCASTRABLES DE 30"(76,2 CM)

Table of Contents/Table des matieres .................................................................................. 2

iMPORTANT:

Save for local electrical inspector's use.

installer: Leave installation instructions with the homeowner.

Homeowner: Keep installation instructions for future reference.

iMPORTANT :

,_,conserver pour consultation par I'inspecteur local des installations 61ectriques.

Installateur : Remettre les instructions d'installation au propri6taire.

Propri_taire : Conserver les instructions d'installation pour r6f6rence ult6rieure.

W10246118C

TABLEOF CONTENTS TABLE DES MATIERES

RANGE SAFETY ............................................................................. 2

INSTALLATION REQUIREMENTS ................................................ 4

Tools and Parts ............................................................................ 4

Location Requirements ................................................................ 4

Electrical Requirements ............................................................... 7

Gas Supply Requirements ........................................................... 7

Countertop Preparation ............................................................... 8

INSTALLATION INSTRUCTIONS .................................................. 9

Unpack Range .............................................................................. 9

Measure for Proper Height ........................................................... 9

Adjust Leveling Legs .................................................................. 10

Install Anti-Tip Bracket ............................................................... 10

Remove Warming or Storage Drawer ........................................ 11

Verify Anti-Tip Bracket Location ................................................ 11

Level Range ................................................................................ 11

Make Gas Connection ............................................................... 11

Electronic Ignition System ......................................................... 13

Replace Oven Racks and Warming or Storage Drawer ............ 15

Complete Installation ................................................................. 15

GAS CONVERSIONS .................................................................... 16

LP Gas Conversion .................................................................... 16

Natural Gas Conversion ............................................................. 18

ANTI-TIP BRACKET TEM PLATE ................................................ 39

SECURITE DE LA CUISINIERE ................................................... 21

EXIGENCES D'INSTALLATION ................................................... 22

Outillage et pieces ...................................................................... 22

Exigences d'emplacement ......................................................... 22

Specifications electriques .......................................................... 25

Specifications de ralimentation en gaz ..................................... 25

Preparation du plan de travail.................................................... 26

INSTRUCTIONS D'INSTALLATION ............................................. 27

Deballage de la cuisiniere .......................................................... 27

Mesures pour une hauteur appropriee ...................................... 27

Reglage des pieds de nivellement ............................................. 28

Installation de la bride antibasculement .................................... 28

Retrait du tiroir-rechaud ou du tiroir de remisage ..................... 29

Verification de I'emplacement de la bride antibasculement ......29

Reglage de I'aplomb de la cuisiniere ......................................... 29

Raccordement & la canalisation de gaz ..................................... 30

Systeme d'allumage electronique .............................................. 31

Reinstallation des grilles du four et du

tiroir-rechaud ou du tiroir de remisage ...................................... 33

Achever I'installation .................................................................. 34

CONVERSIONS POUR CHANGEMENT DE GAZ....................... 34

Conversion pour I'alimentation au propane ............................... 34

Conversion pour I'alimentation au gaz naturel .......................... 37

GABARIT POUR LA BRIDE ANTIBASCULEMENT .................... 39

RANGE SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

WARNING: If the information in this manual is not followed exactly, a fire or explosion

may result causing property damage, personal injury or death.

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this

or any other appliance.

- WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch.

• Do not use any phone in your building.

• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency or

the gas supplier,

WARNING: Gas leaks cannot always be detected by smell.

Gas suppliers recommend that you use a gas detector approved by UL or CSA.

For more information, contact your gas supplier.

If a gas leak is detected, follow the "What to do if you smell gas" instructions.

In the State of Massachusetts, the following installation instructions apply:

[] Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by

the State of Massachusetts.

[] If using a ball valve, it shall be a T-handle type.

[] A flexible gas connector, when used, must not exceed 3 feet.

Tip Over Hazard

A child or adult can tip the range and be killed.

Connect anti=tip bracket to rear range foot.

Reconnect the anti=tip bracket, if the range is moved.

Failure to follow these instructions can result in death or serious burns to children and adults.

INSTALLATION REQUIREMENTS

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools needed

Rear Filler Strip (optional}

The filler strip may be used to fill a gap between the rear of the

slide-in range and the wall in a freestanding range cutout.

• Tape measure • Masking tape

• Flat-blade screwdriver • Pipe-joint compound

resistant to LP gas

• Phillips screwdriver

• Level • 3/16"(4.8 mm) carbide-tipped

masonry drill bit (for

• Hand or electric drill concrete/ceramic floors)

• Hammer • Noncorrosive leak-detection

solution

• Wrench or pliers

For LP/Natural Gas

• Pipe wrench

Conversions

• 1%6"combination wrench • 1/2"combination wrench

• 3/8"nut driver • 7 mm combination wrench

• V8"(3.2 mm) drill bit (for • 7 mm nut driver

wood floors)

• Size T20 Torx®tscrewdriver

• Marker or pencil

Parts supplied

Check that all parts are included.

A. Filler strip

B. Countertop

C. Countertop cutout

To order, see the "Assistance or Service" section of the Use and

Care Guide. Order Part Number W10113902A (black),

W10113903A (white) or W10113904A (biscuit).

A. Anti-tip bracket

B. Plastic anchors (2)

C. #10 x 1/2"screws (2)

Anti-tip bracket must be securely mounted to subfloor.

Thickness of flooring may require longer screws to anchor

bracket to subfloor. Longer screws are available from your

local hardware store.

Parts needed

Check local codes and consult gas supplier. Check existing gas

supply and electrical supply. See "Electrical Requirements" and

"Gas Supply Requirements" sections.

IMPORTANT: Observe all governing codes and ordinances. Do

not obstruct flow of combustion and ventilation air.

• It is the installer's responsibility to comply with installation

clearances specified on the model/serial rating plate. The

model/serial rating plate is located inside the oven door on

the right-hand side oven door trim.

• The range should be located for convenient use in the

kitchen.

• Recessed installations must provide complete enclosure of

the sides and rear of the range.

• To eliminate the risk of burns or fire by reaching over heated

surface units, cabinet storage space located above the

surface units should be avoided. If cabinet storage is to be

provided, the risk can be reduced by installing a range hood

or microwave hood combination that projects horizontally a

minimum of 5" (12.7 cm) beyond the bottom of the cabinets.

• All openings in the wall or floor where range is to be installed

must be sealed.

• Do not seal the range to the side cabinets.

• Cabinet opening dimensions that are shown must be used.

Given dimensions are minimum clearances.

• The floor anti-tip bracket must be installed. To install the anti-

tip bracket shipped with the range, see "Install Anti-Tip

Bracket" section.

1-®TORX is a registered trademark of Saturn Fasteners, Inc.

• Groundedelectricalsupplyisrequired.See"Electrical

Requirements"section.

• Propergassupplyconnectionmustbeavailable.See"Gas

SupplyRequirements"section.

• Contactaqualifiedfloorcoveringinstallertocheckthatthe

floorcoveringcanwithstandatleast200°F(93°C).

• Useaninsulatedpador1¼,,(0.64cm)plywoodunderrangeif

installingrangeovercarpeting.

IMPORTANT:Toavoiddamagetoyourcabinets,checkwithyour

builderorcabinetsuppliertomakesurethatthematerialsused

willnotdiscolor,delaminateorsustainotherdamage.Thisoven

hasbeendesignedinaccordancewiththerequirementsofUL

andCSAInternationalandcomplieswiththemaximumallowable

woodcabinettemperaturesof194°(90°C).

Mobile Home - Additional Installation Requirements

The installation of this range must conform to the Manufactured

Home Construction and Safety Standard, Title 24 CFR, Part 3280

(formerly the Federal Standard for Mobile Home Construction

and Safety, Title 24, HUD Part 280). When such standard is not

applicable, use the Standard for Manufactured Home

Installations, ANSI A225.1/NFPA 501A or with local codes.

In Canada, the installation of this range must conform with the

current standards CAN/CSA-A240-1atest edition, or with local

codes.

Mobile home installations require:

• When this range is installed in a mobile home, it must be

secured to the floor during transit. Any method of securing

the range is adequate as long as it conforms to the standards

listed above.

Product Dimensions

Freestanding Range Slide-in Range

A. 53/4'' (14.6 cm)

B. 30" (76.2 cm)

C. 413/4'' (106 cm) overall height

with levering legs screwed all

the way in

D. 36" (91.4 cm) cooktop trim

height with levering legs

screwed all the way in*

E. Model/serial number plate

(located on the right-hand

side oven door trim)

F. 27¼" (69.2 cm) max. from

handle to standoff at back

of range**

*Range can be raised approximately 1" (2.5 cm) by adjusting

the leveling legs.

**When installed in a 24" (61 cm) base cabinet with 25" (63.5 cm)

countertop; front of oven door protrudes 1" (2.5 cm) beyond

24" (61 cm) base cabinet.

A. 30%6" (77.6 cm)

B. 35%" (90.5 cm) height to

underside of cooktop edge

with leveling legs screwed

all the way in*

C. Model/serial number plate

(located on the right-hand

side oven door trim)

D. 30" (76.2 cm)

E. 27¼" (69.2 cm)

(271_ ''[70.3 cm] on

models KGRS80 7XSP

and KGSS907XSP) from

handle to standoff at

back of range**

F. 23" (58.4 cm) countertop

notch to rear of cooktop

*Range can be raised approximately 1" (2.5 cm) by adjusting

the leveling legs.

**When installed in a 24" (61.0 cm) base cabinet with

25" (63.5 cm) countertop; front of oven door protrudes

13/4"(4.4 cm) (23A6 '' [5.5 cm] on models KGRS807XSP and

KGSS907XSP) beyond 24" (61.0 cm) base cabinet.

Installation Clearances

Cabinet opening dimensions shown are for 25" (64 cm) countertop depth, 24" (61 cm) base cabinet depth and 36" (91.4 cm)

countertop height.

IMPORTANT: If installing a range hood or microwave hood combination above the range, follow the range hood or microwave hood

combination installation instructions for dimensional clearances above the cooktop surface.

Freestanding Ranges

A. 18" (45. 7 cm) upper cabinet to countertop

B. 13" (33 cm) upper cabinet depth

C. 30" (76.2 cm) min. opening width

D. For minimum clearance to top of the cooktop, see NOTE.

E. 30" (76.2 cm) min. opening width

F. This shaded area recommended for installation of rigid gas pipe.

G. 6" (15.2 cm) available area for gas and electric installation

H. Grounded outlet

I. 7" (17.8 cm)

J. 11/2'' (3.8 cm)

K. 41/2"(11.4 cm)

L. 5" (12.7 cm) min. clearance from both sides of the range to the

side wall or other combustible material.

M. Cabinet door or hinge should not extend into the cutout.

Slide-In Ranges

A. 18" (45.7 cm) upper cabinet to countertop

B. 13" (33 cm) max. upper cabinet depth

C. 30" (76.2 cm) min. opening width

D. For minimum clearance to top of the cooktop, see NOTE.

E. 30" (76.2 cm) min. opening width

F. This shaded area recommended for installation of rigid gas pipe.

G. 6" (15.2 cm) available area for gas and electric installation

H. Grounded outlet

I. 7" (17.8 cm)

J. 11/2'' (3.8 cm)

K. 41/2"(11.4 cm)

L. 5" (12. 7 cm) min. clearance from both sides of the range to the

side wall or other combustible material for models KGSS907 and

KGRS80 7.

2" (5.1 cm) min. clearance for model KGSKg01

M. 221_,, (58.3 cm) opening depth

N. 3/4"(1.9 cm) radius both corners

Q. Cabinet door or hinge should not extend into the cutout.

NOTE: 24" (61 cm) minimum when bottom of wood or metal cabinet is covered by not less than 1/4"(0.64 cm) flame retardant millboard

covered with not less than No. 28 MSG sheet steel, 0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm) aluminum or

0.020" (0.5 mm) copper.

30" (76.2 cm) minimum clearance between the top of the cooking platform and the bottom of an uncovered wood or metal cabinet.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

IMPORTANT: The range must be electrically grounded in

accordance with local codes and ordinances, or in the absence

of local codes, with the National Electrical Code, ANSI/NFPA 70

or Canadian Electrical Code, CSA C22.1.

This range is equipped with an electronic ignition system that will

not operate if plugged into an outlet that is not properly polarized.

If codes permit and a separate ground wire is used, it is

recommended that a qualified electrical installer determine that

the ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park

Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

• A 120 volt, 60 Hz., AC only, 15-amp fused, electrical circuit is

required. A time-delay fuse or circuit breaker is also

recommended. It is recommended that a separate circuit

serving only this range be provided.

• Electronic ignition systems operate within wide voltage limits,

but proper grounding and polarity are necessary. Check that

the outlet provides 120-volt power and is correctly grounded.

• The wiring diagram is located on the underside of the storage

drawer or below the warming drawer in a clear plastic bag.

NOTE: The metal chassis of the range must be grounded in

order for the control panel to work. If the metal chassis of the

range is not grounded, no keypads will operate. Check with a

qualified electrician if you are in doubt as to whether the

metal chassis of the range is grounded.

_/i_ ,,,_ ,_ ,

Explosion Hazard

Use a new CSA International approved gas supply line.

Install a shut=off valve.

Securely tighten all gas connections.

if connected to LP, have a qualified person make sure

gas pressure does not exceed 14" (36 cm) water

column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

Observe all governing codes and ordinances.

IMPORTANT: This installation must conform with all local codes

and ordinances. In the absence of local codes, installation must

conform with American National Standard, National Fuel Gas

Code ANSI Z223.1 - latest edition or CAN/CGA B149 - latest

edition.

IMPORTANT: Leak testing of the range must be conducted

according to the manufacturer's instructions.

Type of Gas

Natural gas:

This range is design-certified by CSA International for use with

Natural gas or, after proper conversion, for use with LP gas.

• This range is factory set for use with Natural gas. See "Gas

Conversions" section. The model/serial rating plate located

behind the storage drawer on the right-hand side oven door

frame has information on the types of gas that can be used. If

the types of gas listed do not include the type of gas

available, check with the local gas supplier.

LP gas conversion:

Conversion must be done by a qualified service technician.

No attempt shall be made to convert the appliance from the gas

specified on the model/serial rating plate for use with a different

gas without consulting the serving gas supplier. See "Gas

Conversions" section.

Gas Supply Line

• Provide a gas supply line of 3_,,(1.9 cm) rigid pipe to the

range location. A smaller size pipe on longer runs may result

in insufficient gas supply. With LP gas, piping or tubing size

can be 1/2"(1.3 cm) minimum. Usually, LP gas suppliers

determine the size and materials used in the system.

NOTE: Pipe-joint compounds that resist the action of LP gas

must be used. Do not use TEFLON ®t tape.

1-®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.

Flexible metal appliance connector:

If local codes permit, a new CSA design-certified,

4 to 5 ft (122 to 152.4 cm) long, 1/2"(1.3 cm) or

3_,,(1.9 cm) I.D., flexible metal appliance connector may

be used for connecting range to the gas supply line.

• A 1/2"(1.3 cm) male pipe thread is needed for connection

to the female pipe threads of the inlet to the appliance

pressure regulator.

• Do not kink or damage the flexible metal tubing when

moving the range.

Rigid pipe connection:

The rigid pipe connection requires a combination of pipe

fittings to obtain an in-line connection to the range. The rigid

pipe must be level with the range connection. All strains must

be removed from the supply and fuel lines so range will be

level and in line.

Must include a shutoff valve:

The supply line must be equipped with a manual shutoff

valve. This valve should be located in the same room but

external to the range opening, such as an adjacent cabinet. It

should be in a location that allows ease of opening and

closing. Do not block access to shutoff valve. The valve is for

turning on or shutting off gas to the range.

A. Gas supply line

B. Shutoff valve "open" position

C. To range

Gas Pressure Regulator

The gas pressure regulator supplied with this range must be

used. The inlet pressure to the regulator should be as follows for

proper operation:

Natural gas:

Minimum pressure: 5" WCP

Maximum pressure: 14" WCP

LP gas:

Minimum pressure: 11" WCP

Maximum pressure: 14" WCP

Contact local gas supplier if you are not sure about the inlet

pressure.

Burner Input Requirements

Input ratings shown on the model/serial rating plate are for

elevations up to 2,000 ft (609.6 m).

For elevations above 2,000 ft (609.6 m), ratings are reduced at a

rate of 4% for each 1,000 ft (304.8 m) above sea level (not

applicable for Canada).

Gas Supply Pressure Testing

Gas supply pressure for testing regulator must be at least

1" water column pressure above the manifold pressure shown on

the model/serial rating plate.

Line pressure testing above 1/2psi gauge (14" WCP)

The range and its individual shutoff valve must be disconnected

from the gas supply piping system during any pressure testing of

that system at test pressures in excess of 1/2psi (3.5 kPa).

Line pressure testing at 1/2psi gauge (14" WCP) or lower

The range must be isolated from the gas supply piping system by

closing its individual manual shutoff valve during any pressure

testing of the gas supply piping system at test pressures equal to

or less than 1/2psi (3.5 kPa).

__ _ _ C __ _ :_., _ -_

The cooktop sides of the slide-in range fit over the cutout edge of

your countertop.

If you have a square finish (flat) countertop and the opening width

is 30" (76.2 cm), no countertop preparation is required.

Formed front-edged countertops must have molded edge

shaved flat 3/8"(1.0 cm) from each front corner of opening.

Tile countertops may need trim cut back 3/8"(1.0 cm) from each

front corner and/or rounded edge flattened.

30"

(76.2 cm)

'_(1 0cm)

303A ''

(78.1 crn)

If countertop opening width is greater than 30" (76.2 cm), adjust

the 3/8"(1.0 cm) dimension.

Countertop must be level. Place level on countertop, first side to

side, then front to back. If countertop is not level, range will not

be level. Range must be level for satisfactory baking conditions.

INSTALLATION INSTRUCTIONS

2. Measure from the floor to the underside of the range cooktop.

Excessive Weight Hazard

Use two or more people to move and install range.

Failure to do so can result in back or other injury.

Remove shipping materials, tape and film from the range.

Keep cardboard bottom under range. Remove oven racks

and parts package from inside oven.

To place range on its back, take 4 cardboard corners from the

carton. Stack one cardboard corner on top of another.

Repeat with the other 2 corners. Place them lengthwise on

the floor behind the range to support the range when it is laid

on its back. Using 2 or more people, firmly grasp the range

and gently lay it on its back on the cardboard corners.

Slide-In Ranges:

1. Measure the distance of the countertop to the floor. Measure

at all 4 locations corresponding to the 4 corners of the

underside of the range cooktop, as shown.

A. Distance from the floor to

underside of range cooktop

B. Grate

C. Cooktop surface

D. Range side frame

Your leveling height will be the difference between the

2 measurements you have just taken.

Freestanding Ranges:

1. Measure the distance of the countertop to the floor.

2. Measure from the top of the range cooktop trim to the floor.

A. Distance from the top of the range

cooktop trim to the floor

Your leveling height will be the difference between the

2 measurements you have just taken.

Measure at locations marked A, B, C, D.

................... 0 ........;;J

If range height adjustment is necessary, use a wrench or

pliers to loosen the 4 leveling legs.

This may be done with the range on its back or with the range

supported on 2 legs after the range has been placed back to

a standing position.

NOTE: To place range back up into a standing position, put a

sheet of cardboard or hardboard in front of range. Using 2 or

more people, stand range back up onto the cardboard or

hardboard.

Tip Over Hazard

A child or adult can tip the range and be killed.

Connect anti=tip bracket to rear range foot.

Reconnect the anti=tip bracket, Jf the range is moved.

Failure to follow these instructions can result in death

or serious burns to children and adults.

2. Adjust the leveling legs to the correct height. Leveling legs

can be loosened to add up to a maximum of 1" (2.5 cm). A

minimum of 3/16"(5.0 mm) is needed to engage the anti-tip

bracket.

NOTE: If height adjustment is made when range is standing,

tilt the range back to adjust the front legs, then tilt forward to

adjust the rear legs.

3. When the range is at the correct height, check that there is

adequate clearance under the range for the anti-tip bracket.

Before sliding range into its final location, check that the anti-

tip bracket will slide under the range and onto the rear

leveling leg prior to anti-tip bracket installation.

Contact a qualified floor covering installer for the best procedure

for drilling mounting holes through your type of floor covering.

Before moving range, slide range onto shipping base, cardboard

or hardboard.

1. Remove template from the anti-tip bracket kit (found inside

the oven cavity) or from the back of this manual.

2. Place template on the floor in cabinet opening so that the left

edge is against cabinet and top edge is against rear wall,

molding or cabinet.

3. Tape template into place.

If countertop is not flush with cabinet opening edge, align

template with overhang.

If cabinet opening is wider than that specified in the "Location

Requirements" section, adjust template so range will be

centered in cabinet opening.

To mount anti-tip bracket to wood floor, drill two 1/8"(3.2 mm)

holes at the positions marked on the bracket template.

Remove template from floor.

To mount anti-tip bracket to concrete or ceramic floor, use a

3/16"(4.8 mm) masonry drill bit to drill 2 holes at the positions

marked on the bracket template. Remove template from floor.

Tap plastic anchors into holes with a hammer.

Align anti-tip bracket holes with holes in floor. Fasten anti-tip

bracket with screws provided.

Depending on the thickness of your flooring, longer screws

may be necessary to anchor the bracket to the subfloor.

Longer screws are available from your local hardware store.

Move range close enough to opening to allow for final

electrical connection. Remove shipping base, cardboard or

hardboard from under range.

Move range into its final location, making sure rear leveling

leg slides into anti-tip bracket.

9. If installing the range in a mobile home, you must secure the

range to the floor. Any method of securing the range is

adequate as long as it conforms to the standards in the

"Location Requirements" section.

10. Continue installing your range using the following installation

instructions.

Remove the warming or storage drawer to gain access to the

lower section of the range. This will be necessary for some of the

following installation steps.

To Remove Warming Drawer:

1. Open drawer to its fully open position.

2. Locate the black loops on both sides of the drawer.

A.Loop

Pull both loops forward at the same time, then pull drawer out

another inch.

4. Holding the drawer by its sides, not its front, gently pull it all

the way out.

To Remove Storage Drawer:

1. Pull drawer straight out to the first stop.

2. Lift up the back of the drawer and pull out.

IMPORTANT: On models with a warming drawer, the rear range

foot must be viewed from the front and slightly to one side of the

range.

1. To check that the anti-tip bracket is installed, use a flashlight

and look underneath the bottom of the range.

• Look for the anti-tip bracket securely attached to floor.

• Slide range back so rear range foot is under anti-tip

bracket.

3. If range is not level, pull range forward until rear leveling leg is

removed from the anti-tip bracket.

Use a wrench or pliers to adjust leveling legs up or down until

the range is level. Push range back into position. Check that

rear leveling leg is engaged in the anti-tip bracket.

NOTE: Range must be level for satisfactory baking performance.

Explosion Hazard

Use a new CSA International approved gas supply line.

install a shut=off valve.

Securely tighten all gas connections.

if connected to LP, have a qualified person make sure

gas pressure does not exceed 14" (36 cm) water

column.

Examples of a quaJified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

Typical rigid pipe connection

A combination of pipe fittings must be used to connect the range

to the existing gas line. Your connections may be different,

according to the supply line type, size and location.

1. Apply pipe-joint compound made for use with LP gas to all

pipe thread connections.

2. Using a pipe wrench to tighten, connect the gas supply to the

range.

........D

Place rack in oven.

Place level on rack and check levelness of the range, first

side to side; then front to back.

A. Gas pressure regulator

B. 90 ° elbow (must have

_/2"male pipe thread)

C. Nipple

D. Union

E.Black iron pipe

F. Manual gas shutoff valve

G. _/2"or 3/_,,gas pipe

H. Nipple

I. Union

J. 90 °elbow

Typical flexible connection

1. Apply pipe-joint compound made for use with LP gas to the

smaller thread ends of the flexible connector adapters (see B

and G in the following illustration).

2. Attach one adapter to the gas pressure regulator and the

other adapter to the gas shutoff valve. Tighten both adapters.

3. Use a 1%e"combination wrench and channel lock pliers to

attach the flexible connector to the adapters. Check that

connector is not kinked.

A B C

/ iD

, S' _

A. Gas pressure regulator

B. Use pipe-joint compound.

C. Adapter (must have V2"male

pipe thread)

D. Flexible connector

H G F

E.Manual gas shutoff valve

F V2"or 3/4"gas pipe

G. Use pipe-joint compound.

H. Adapter

Complete Connection

1. Locate gas pressure regulator at rear of storage or warming

drawer compartment.

NOTE: On models with a warming drawer, an access cover

must be removed from the gas pressure regulator.

A. Gas pressure regulator

IMPORTANT: Do not remove the gas pressure regulator.

Check that the gas pressure regulator shutoff valve is in the

"ON" position. The valve is on when the lever is parallel to the

floor.

A. Gaspressure regulator shutoff valve

3. Open the manual shutoff valve in the gas supply line. The

valve is open when the handle is parallel to the gas pipe.

Test all connections by brushing on an approved

noncorrosive leak-detection solution. If bubbles appear, a

leak is indicated. Correct any leak found.

Remove cooktop burner caps and grates from parts

package. Align notches in burner caps with pins in burner

base. Burner caps should be level when properly positioned.

If burner caps are not properly positioned, surface burners

will not light.

A. Burner base

B. Burner cap

C. Burner grate

Place burner grates over burners and caps as shown in the

following illustration. When properly installed the grates

should not overlap the console.

Freestanding Models

I..................................;k

A.Opening in grate for wok insert to be

located over left front burner

Slide-In Models

.............................

........ 7

A. Large flange with rounded cornermust be

atrear corner of the cooktop.

A. Closed valve

B. Open valve

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

7. Plug into a grounded 3 prong outlet.

L,IQCI]O s c I£ s [ ()s I!s_'t/_5I!-@ls.

_J J

Initial lighting and gas flame adjustments

Cooktop and oven burners use electronic igniters in place of

standing pilots. When the cooktop control knob is turned to the

"LITE" position, the system creates aspark to light the burner.

This sparking continues, as long as the control knob is turned to

"LITE."

When the oven control is turned to the desired setting, sparking

occurs and ignites the gas.

Check Operation of Cooktop Burners

Standard Surface Burners

Push in and turn each control knob to the "LITE" position.

The flame should light within 4 seconds. The first time a burner is

lit it may take longer than 4 seconds to light because of air in the

gas line.

TripleTier _ Flame Burner

To start simmer burner:

Push in and turn control knob to "LITE" to start the inner burner.

The flame should light within 4 seconds. The first time a burner is

lit it may take longer than 4 seconds to light because of air in the

gas line.

To start power burner:

Push in control knob again and turn to "POWER BURNER HI"

(turn control knob to DUAL HI on models KGSS907XSP) to light

the outer burner.

The flame should light within 4 seconds. The first time a burner is

lit it may take longer than 4 seconds to light because of air in the

gas line.

If burners do not light properly:

• Turn cooktop control knob to the "OFF" position.

• Check that the range is plugged in and the circuit breaker has

not tripped or the household fuse has not blown.

• Check that the gas shutoff valves are set to the "open"

position.

• Check that burner caps are properly positioned on burner

bases.

Repeat start-up. If a burner does not light at this point, turn the

control knobs to "Off" and contact your dealer or authorized

service company for assistance.

Adjust Flame Height

Adjust the height of top burner flames. The cooktop "low" burner

flame should be a steady blue flame approximately 1¼.(0.64 cm)

high.

A. Low flame

B. High flame

To adjust standard burners:

The flame can be adjusted using the adjustment screw in the

center of the valve stem. The valve stem is located directly

underneath the control knob.

A. Valve stem

If the "low" flame needs to be adjusted:

1. Remove the control knob.

2. Hold the knob stem with a pair of pliers. Use a small flat-

blade screwdriver to turn the screw located in the center of

the control knob stem until the flame is the proper size.

3. Replace the control knob.

4. Test the flame by turning the control from "LO" to "HI,"

checking the flame at each setting.

To adjust TripleTier ®Flame burner:

1. Remove the control knob.

2. Insert a flat-blade screwdriver into adjustment locations

shown in the following illustration and engage the slotted

screw. Turn the screw until the flame is the proper size.

A. Simmer burner regulation

B. Pc wer burner regulation

3. Replace the control knob.

4. Test the flame by turning the control from "LO" to "HI,"

checking the flame at each setting.

Check Operation of Oven Bake Burner

1. Remove the oven rack. Remove the bake burner cover and

place it on a covered surface.

2. Push the BAKE pad. Default temperature appears in the

temperature display.

3. Press the START pad. "Preheating" and "Lo" (or actual

temperature) will appear in the temperature display.

The oven bake burner should light within 8 seconds, under

certain conditions it may take the burner up to 50 to 60 seconds

to light.

Electronic igniters are used to light the bake and broil burners.

.........................

BIZZZI

A. Oven bake burner cover

B. Flame spreader

C. Oven bake burner

Adjust Oven Bake Flame (if needed)

1. Remove access cover plate (2 screws) located on the upper

wall, inside the storage or warming drawer compartment.

2. Check the oven bake burner for proper flame.

This flame should have a 1/2"(1.3 cm) long inner cone of

bluish-green, with an outer mantle of dark blue, and should

be clean and soft in character. No yellow tips, blowing or

lifting of flame should occur.

3. If the oven bake flame needs to be adjusted, locate the air

shutter near the center rear of the range. Use a flat-blade

screwdriver to loosen the locking screw. Rotate the air shutter

until the proper flame appears. Tighten locking screw.

Check Operation of Oven Broil Burner

1. Close the oven door.

2. Press the BROIL pad. "FULL BROIL" and broil temperature

will appear in the temperature display.

3. Press the START pad. "ON" indicator will light.

The oven burner should light within 8 seconds, under certain

conditions it may take the burner up to 50 to 60 seconds to

light. On some models, an electric halo element also turns on.

A. Gas burner

B. Electric halo element

NOTE: Oven door must be shut for broil burner to operate.

Adjust Oven Broil Burner Flame (if needed)

Look through oven window to check broil burner for proper

flame. This flame should have a 1/2"(1.3 cm) long inner cone of

bluish-green, with an outer mantle of dark blue, and should be

clean and soft in character. No yellow tips, blowing or lifting of

flame should occur.

A. Air shutter

B. Locking screw

4. Push CANCEL/OFF pad.

5. Reinstall oven bake burner access plate.

A. Locking screw

B. Air shutter

If flame needs to be adjusted:

1. Use a flat-blade screwdriver to loosen the locking screw on

the air shutter located at the rear of the broil burner.

2. Adjust the air shutter as need.

3. Tighten lock screw.

.......k¢;e:i a..... Racks ausd o::

Replace oven racks in oven cavity. Replace warming drawer or

storage drawer.

To Replace Warming Drawer:

1. Align the drawer glides with the receiving guides.

2. Push drawer in all the way.

Gently open and close the drawer to ensure it is seated properly

on the slides.

To Replace Storage Drawer:

1. Fit the ends of the drawer rails into the guides in the cavity.

2. Slide the drawer closed.

1. Check that all parts are now installed. If there is an extra part,

go back through the steps to see which step was skipped.

2. Check that you have all of your tools.

3. Dispose of/recycle all packaging materials.

4. Check that the range is level. See "Level Range."

5. Use a mild solution of liquid household cleaner and warm

water to remove waxy residue caused by shipping material.

Dry thoroughly with a soft cloth. For more information, see

the "Range Care" section of the Use and Care Guide.

6. Read the Use and Care Guide.

7. Turn on surface burners and oven. See the Use and Care

Guide for specific instruction on range operation.

If range does not operate, check the following:

• Household fuse is intact and tight, or circuit breaker has not

tripped.

• Range is plugged into a grounded 3 prong outlet.

• Electrical supply is connected.

• See "Troubleshooting" in the Use and Care Guide.

8. When the range has been on for 5 minutes, check for heat. If

the range is cold, turn off the range and check that the gas

supply line shutoff valve is open.

• If the gas supply line shutoff valve is closed, open it, then

repeat the 5-minute test as outlined above.

• If the gas supply line shutoff valve is open, press the

CANCEL button on the oven control panel and contact a

qualified technician.

If you need Assistance or Service:

Please reference the "Assistance or Service" section of the Use

and Care Guide or contact the dealer from whom you purchased

your range.

GAS CONVERSIONS

Gas conversions from Natural gas to LP gas or from LP gas to

Natural gas must be done by a qualified installer.

Explosion Hazard

Use a new CSA International approved gas supply line.

Install a shut-off valve.

Securely tighten all gas connections.

if connected to LP, have a qualified person make sure

gas pressure does not exceed 14" (36 cm) water

column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

Tip Over Hazard

A child or adult can tip the range and be killed.

Connect anti=tip bracket to rear range foot.

Reconnect the anti-tip bracket, if the range is moved.

Failure to follow these instructions can result in death

or serious burns to children and adults.

Remove warming drawer or storage drawer. See the

"Remove Warming or Storage Drawer" section for

instructions. Locate gas pressure regulator at rear of storage

or warming drawer compartment.

NOTE: On models with a warming drawer, an access cover

must be removed from the gas pressure regulator.

A. Gas pressure regulator

IMPORTANT: Do not remove the gas pressure regulator.

Gas pressure regulator

4. Remove plastic cover from gas pressure regulator cap.

5. Turn gas pressure regulator cap (marked "N" on front of gas

pressure regulator) counterclockwise with a wrench to

remove.

NOTE: Do not remove the spring beneath the cap.

Side view before

D )E

Side viewafter

A. Plastic cover

B. Gas pressure regulator cap with solid end facing out

C. Gas pressure regulator cap with hollow end facing out

D. Washer

E. Gas pressure regulator cap

F. Gas regulator shutoff valve (shown in the "open" position)

To Convert Gas Pressure Regulator

Turn manual shutoff valve to the "closed" position.

Unplug range or disconnect power.

..................B

A_J ............. ....................C

A. Torange

B.Manual shutoff valve "closed" position

C.Gassupply fine

6. Turn the gas pressure regulator cap over and reinstall on

regulator so that the hollow end faces out and letters "LP" are

visible.

7. Replace plastic cover over gas pressure regulator cap.

To Convert Standard Surface Burners

1. Remove burner cap.

2. Using a T20 Torx®screwdriver, remove the burner base.

3. Apply masking tape to the end of a 7 mm nut driver to help

hold the gas orifice spud in the nut driver while changing it.

Press nut driver down onto the gas orifice spud and remove

by turning it counterclockwise and lifting out. Set gas orifice

spud aside.

3. Remove the plate on the external gas orifice spud.

A. Igniter electrode

B. Gas tube opening

C. Burner cap

D. Burner base

Gas orifice spuds are stamped with a number, marked with

1 color dot, and have a groove in the hex area. Replace the

Natural gas orifice spud with the correct LP gas orifice spud.

o ..................................................................C

A. Burner caps

B. Burner heads

C. External gas orifice spud access plate

D. Internal gas orifice spud

IMPORTANT: The TripleTier ®Flame burner has 2 gas orifice

spuds. Do not forget to change the external gas orifice spud

located under the plate.

A. Groove

Refer to the following chart for correct LP gas orifice spud

placement.

LP Gas Orifice Spud Chart for Standard Surface Burners

Burner Location Burner Rating Color Size

Right front 5,000 Btu/h Red 0.70 mm

Left front 13,000 Btu/h Green 1.10 mm

Right rear 10,000 Btu/h Blue 0.95 mm

Left rear 5,000 Btu/h Red 0.70 mm

5. Place Natural gas orifice spuds in plastic parts bag for future

use and keep with package containing literature.

6. Replace burner cap.

7. Repeat steps 1-6 for the remaining burners, except for the

TripleTier ®Flame burner (on some models). See "To Convert

TripleTier ®Flame Burners" section.

To Convert TripleTier _ Flame Burners (on some models)

1. Remove burner cap.

2. Remove the burner head using a size T20 Torx®screwdriver.

A. Plate

B. External gas orifice spud

C. Internal gas orifice spud

4. Apply masking tape to the end of a 7 mm nut driver to help

hold the internal gas orifice spud in the nut driver while

changing it. Press nut driver down onto the internal gas

orifice spud and remove by turning it counterclockwise and

lifting out. Set internal gas orifice spud aside.

5. Use a 7 mm combination wrench to remove the external gas

orifice spud. Turn counterclockwise to remove. Set external

gas orifice spud aside.

6. Replace each Natural gas orifice spud with the correct LP gas

orifice spud. Refer to the following chart for correct LP gas

orifice spud placement.

LP Gas Orifice Spud Chart for TripleTier ®Flame Burners

Burner Location Burner Rating Color Size

Left front (external 11,800 Btu/h Brown 1.00 mm

TripleTier ®burner)

Left front (internal 2,200 Btu/h Orange 0.42 mm

TripleTier ®burner)

7. Replace burner plate, head and cap.

8. Place Natural gas orifice spuds in plastic parts bag for future

use and keep with package containing literature.

To Convert Oven Bake Burner

1. Remove oven racks.

2. Use a 1/2"combination wrench to turn the orifice hood

clockwise (about 2 to 21/2turns) so it is snug onto the pin.

IMPORTANT: Do not overtighten.

NOTE: Turning the orifice hood clockwise will decrease flame

size; turning it counterclockwise will increase flame size.

The oven bake burner flame cannot be properly adjusted if

this conversion is not made. See "Adjust Oven Bake Flame"

in the "Electronic Ignition System" section.

A. Orifice hood

B. Pin

To Convert Oven Broil Burner

1. Use a 1/2"combination wrench to turn the orifice hood

clockwise (about 2 to 21/2turns) so it is snug onto the pin.

IMPORTANT: Do not overtighten.

NOTE: Turning the orifice hood clockwise will decrease flame

size; turning it counterclockwise will increase flame size.

The oven broil burner flame cannot be properly adjusted if

this conversion is not made. See "Adjust Oven Broil Burner

Flame" in the "Electronic Ignition System" section.

A. Locking screw

B. Orifice hood

Reinstall the warming or storage drawer. See the "Replace

Oven Racks and Warming or Storage Drawer" section for

instructions.

Complete installation. See "Make Gas Connection" and

"Electronic Ignition System" sections.

Checking for proper cooktop burner flames and oven burner

flames is very important. The small inner cone should have a

very distinct blue flame 1¼,,(0.6 cm) to 1/2"(1.3 cm) long. The

outer cone is not as distinct as the inner cone. LP gas flames

have a slightly yellow tip.

IMPORTANT: You may have to adjust the "LO" setting for

each cooktop burner.

Tip Over Hazard

A child or adult can tip the range and be killed.

Connect anti=tip bracket to rear range foot.

Reconnect the anti=tip bracket, if the range is moved.

Failure to follow these instructions can result in death

or serious burns to children and adults.

To Convert Gas Pressure Regulator

1. Turn manual shutoff valve to the "closed" position.

2. Unplug range or disconnect power.

....................•...................S

........................C

A. To range

B. Manual shutoff valve "closed" position

C. Gas supply line

Remove warming drawer or storage drawer. See the

"Remove Warming or Storage Drawer" section for

instructions. Locate gas pressure regulator at rear of storage

or warming drawer compartment.

NOTE: On models with a warming drawer, an access cover

must be removed from the gas pressure regulator.

A. Gas pressure regulator

IMPORTANT: Do not remove the gas pressure regulator.

Gas pressure regulator

4. Remove plastic cover from gas pressure regulator cap.

5. Turn gas pressure regulator cap (marked "LP" on front of gas

pressure regulator) counterclockwise with a wrench to

remove.

NOTE: Do not remove the spring beneath the cap.

Side view before

B F

Side view after

A. Plastic cover

B. Gas pressure regulator cap with hollow end facing out

C. Gas pressure regulator cap with sofid end facing out

D. Washer

E. Gas pressure regulator cap

E Gas regulator shutoff valve (shown in the "open" position)

6. Turn the gas pressure regulator cap over and reinstall on

regulator so that the solid end faces out and letter "N" is

visible.

7. Replace plastic cover over gas pressure regulator cap.

To Convert Standard Surface Burners

1. Remove burner cap.

2. Using a T20 Torx®screwdriver, remove the burner base.

3. Apply masking tape to the end of a 7 mm nut driver to help

hold the gas orifice spud in the nut driver while changing it.

Press nut driver down onto the gas orifice spud and remove

by turning it counterclockwise and lifting out. Set gas orifice

spud aside.

4. Gas orifice spuds are stamped with a number on the side.

Replace the LP gas orifice spud with the correct Natural gas

orifice spud.

A. Stamped number

Refer to the following chart for the correct Natural gas orifice

spud placement.

Natural Gas Orifice Spud Chart for Standard Surface Burners

Burner Location Burner Rating Size

Right front 6,000 Btu/h 1.10 mm

Left front 14,000 Btu/h 1.70 mm

Right rear 12,500 Btu/h 1.61 mm

Left rear 6,000 Btu/h 1.10 mm

5. Place LP gas orifice spuds in plastic parts bag for future use

and keep with package containing literature.

6. Replace burner cap.

7. Repeat steps 1-6 for the remaining burners, except for the

TripleTier ®Flame burner (on some models). See "To Convert

TripleTier ®Flame Burners" section.

To Convert TripleTier _ Flame Burner (on some models)

1. Remove burner cap.

2. Remove the burner head using a size T20 Torx®screwdriver.

3. Remove the plate on the external gas orifice spud.

A. Burner caps

B. Burner heads

C. External gas orifice spud access plate

D. Internal gas orifice spud

A. Igniter electrode

B. Gas tube opening

C. Burner cap

D. Burner base

IMPORTANT: The TripleTier ®Flame burner has 2 gas orifice

spuds. Do not forget to change the external gas orifice spud

located under the plate.

A. Plate

B. External gas office spud

C. Internal gas orifice spud

4. Apply masking tape to the end of a 7 mm nut driver to help

hold the internal gas orifice spud in the nut driver while

changing it. Press nut driver down onto the internal gas

orifice spud and remove by turning it counterclockwise and

lifting out. Set internal gas orifice spud aside.

5. Use a 7 mm combination wrench to remove the external

orifice spud. Turn counterclockwise to remove. Set external

gas orifice spud aside.

6. Replace each LP gas orifice spud with the correct Natural gas

orifice spud. Refer to the following chart for correct Natural

gas orifice spud placement.

Natural Gas Orifice Spud Chart for TripleTier ®Flame Burners

Burner Location Burner Rating Size

Left front (external 12,200 Btu/h 1.70 mm

TripleTier ®burner)

Left front (internal 2,800 Btu/h 0.70 mm

TripleTier ®burner)

7. Replace burner plate, head and cap.

8. Place LP gas orifice spuds in plastic parts bag for future use

and keep with package containing literature.

To Convert Oven Bake Burner

1. Remove oven racks.

2. Use a 1/2"combination wrench to loosen the orifice hood

away from the pin (about 2 to 21/2turns). The oven bake

burner flame cannot be properly adjusted if this conversion is

not made. See "Adjust Oven Bake Flame" in the "Electronic

Ignition System" section.

A. Orifice hood

B. Pin

To Convert Oven Broil Burner

1= Use a 1/2"combination wrench to loosen the orifice hood

away from the pin (about 2 to 21/2turns). The oven broil burner

flame cannot be properly adjusted if this conversion is not

made. See "Adjust Oven Broil Burner Flame" in the

"Electronic Ignition System" section.

A. Locking screw

B. Orifice hood

Reinstall the warming or storage drawer. See the "Replace

Oven Racks and Warming or Storage Drawer" section for

instructions.

Complete installation. See "Make Gas Connection" and

"Electronic Ignition System" sections.

Checking for proper cooktop burner and oven bake burner

flame is very important. Natural gas flames do not have

yellow tips.

IMPORTANT: You may have to adjust "LO" setting for each

cooktop burner.

La page charge ...

KitchenAid KGRS807SBL02 Guide d'installation

Marque: KitchenAid

Modèle: KGRS807SBL02

Catégorie: Cuisinières

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: KitchenAid KGRS807SBL02 Installation guide

KitchenAid KGRS807SBL02 Guide d'installation

KitchenAid KGRS807SBL02 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents