WAGNER PaintREADY System® Manuel utilisateur

Marque: WAGNER

Modèle: PaintREADY System®

Catégorie: Systèmes de pulvérisation fine Power

Taper: Manuel utilisateur

EnglishFrançaisEspañol

1016 • Form No. 0529826K

Owner’s Manual

Read this manual for complete instructions

Français (page 17) / Español (página 33)

PaintREADY

™

System

Contents

2 Important Safety Information

4 Controls and Functions

5 Material Preparation

6/7 Assembly

8 Air and Material Controls

9 Spray Pattern Adjustment

10 Proper Spraying Technique

12 Cleanup

14 Reassembly

15 Maintenance

16 Troubleshooting

49 Parts List

52 Warranty

Questions?

Call Wagner Technical Service at:

1-800-328-8251

www.wagnerspraytech.com

English

Important Safety Information

Read all safety information before

operating the equipment. Save these

instructions.

Indicates a hazardous situation which,

if not avoided, could result in death or

serious injury.

To reduce the risks of re or explosion,

electrical shock and the injury to

persons, read and understand all

instructions included in this manual. Be

familiar with the controls and proper

usage of the equipment.

Grounding Instructions

This product must be grounded. In the event of an

electrical short circuit, grounding reduces the risk

of electric shock by providing an escape wire for

the electric current. This product is equipped with a

cord having a grounding wire with an appropriate

grounding plug. The plug must be plugged into an

outlet that is properly installed and grounded in

accordance with all local codes and ordinances.

WARNING - Improper installation of

the grounding plug can result in a risk

of electric shock.

If repair or replacement of the cord or plug is

necessary, do not connect the green grounding wire

to either at blade terminal. The wire with insulation

having a green outer surface with or without yellow

stripes is the grounding wire and must be connected

to the grounding pin.

Check with a qualied electrician or serviceman

if the grounding instructions are not completely

understood, or if you are in doubt as to whether the

product is properly grounded. Do not modify the

plug provided. If the plug will not t the outlet, have

the proper outlet installed by a qualied electrician.

This product is for use on a nominal 120 volt

circuit and has a grounding plug that looks like

the plug illustrated below. Make sure that the

product is connected to an outlet having the same

conguration as the plug. No adapter should be

used with this product.

Grounded Outlet

Grounding Pin

Cover for grounded outlet box

WARNING - To reduce the risk

of re or explosion:

1. Do not spray ammable or combustible

materials near an open ame, pilot lights

or sources of ignition such as hot objects,

cigarettes, motors, electrical equipment and

electrical appliances. Avoid creating sparks

from connecting and disconnecting power

cords.

2. For use with only water-based or mineral

spirit-type materials with a minimum ash point

of 38ºC (100º F) — Do not spray or clean with

liquids having a ash point of less than 38ºC

(100º F). Flash point is the temperature at which

a uid can produce enough vapor to ignite.

3. Verify that all containers and collection systems

are grounded to prevent static discharge.

4. Connect to a grounded outlet and use

grounded extension cords (electric models

only). Do not use a 3 to 2 adapter.

5. Keep spray area well ventilated. Keep a good

supply of fresh air moving through the area

to keep the air within the spray area free from

accumulation of ammable vapors. Keep pump

assembly in well ventilated area. Do not spray

pump assembly.

6. Do not smoke in the spray area.

7. Do not operate light switches, engines, or

similar spark producing products in the spray

area.

8. Keep area clean and free of paint or solvent

containers, rags, and other ammable materials.

9. Know the contents of the paint and solvents

being sprayed. Read all Material Safety Data

Sheets (MSDS) and container labels provided

with the paints and solvents. Follow the paint

and solvent manufacture’s safety instructions.

10. Fire extinguisher equipment shall be present

and working.

English

Important Safety Information

WARNING - To reduce the risk of

injury:

1. Always wear appropriate gloves, eye protection,

clothing and a respirator or mask when

painting. Hazardous vapors – Paints, solvents,

insecticides, and other materials can be harmful

if inhaled or come in contact with body. Vapors

can cause severe nausea, fainting or poisoning.

2. Do not operate or spray near children. Keep

children away from equipment at all times.

3. Do not overreach or stand on an unstable

support. Keep eective footing and balance at

all times.

4. Stay alert and watch what you are doing.

5. Do not operate the unit when fatigued or under

the inuence of drugs or alcohol.

6. Never aim spray gun at any part of the body.

7. Follow all appropriate local, state, and national

codes governing ventilation, re prevention,

and operation.

8. The United States Government Safety Standards

have been adopted under the Occupational

Safety and Health Act (OSHA). These standards,

particularly part 1910 of the General Standards

and part 1926 of the Construction Standards

should be consulted.

9. Use only manufacturer authorized parts. User

assumes all risks and liabilities when using parts

that do not meet the minimum specications

and safety devices of the turbine manufacturer.

10. Power cord must be connected to a grounded

circuit.

11. All hoses, swivels, guns and accessories must be

rated at or above 10 PSI.

12. Do not spray outdoors on windy days.

13. Use only Wagner HVLP hose.

WARNING - To reduce the risk of

electric shock:

1. Power cord must be connected to a grounded

circuit.

2. Never submerge electrical parts.

3. Never expose the equipment to rain. Store

indoors.

4. Keep electrical cord plug and spray gun trigger

free from paint and other liquids. Never hold

the cord at plug connections to support the

cord. Failure to observe may result in an

electrical shock.

Important Electrical

Information

Use only a 3-wire extension cord that has a 3-blade

grounding plug and a 3-slot receptacle that will

accept the plug on the product. Make sure your

extension cord is in good condition. When using an

extension cord, be sure to use one heavy enough

to carry the current your product will draw. An

undersized cord will cause a drop in line voltage

resulting in loss of power and overheating. A 14

gauge or 12 gauge cord is recommended. If an

extension cord is to be used outdoors, it must be

marked with the sux W-A after the cord type

designation. For example, a designation of SJTW-A

would indicate that the cord would be appropriate

for outdoor use.

IMPORTANT:

Household use only. Intended

for indoor/outdoor use ONLY with materials

having ashpoint above 100ºF (38ºC).

English

Controls and Functions

Air hose

White Spray Gun

Turbine

Yellow Spray Gun

Spray gun

handle

Air pressure

control dial

Turbine

handle

ON / OFF switch

Material ow

control

Trigger

Air cap

Spray width lever

Material ow

control

Material

container

Adjustment

ring

Material

container

Filter housin

(both sides)

Spray gun holder

ON/OFF switch:

The ON/OFF switch turns power

to the turbine on and o. The

ON/OFF switch is located on top

of the carrying handle of the

turbine.

Air pressure control dial:

The air pressure control dial

adjusts the level of air pressure

produced by the turbine.

Material Flow Control:

The material ow control

determines the amount of

spray material that is sprayed

from the spray gun.

Spray Width Lever:

The spray width lever

determines the width of the

spray pattern. (white gun

only).

English

Material Preparation

Note: Material to be sprayed may need to be strained

to remove any impurities in the paint which may enter

and clog the system. Impurities in the paint will give

poor performance and a poor finish.

Note: Only thin the material if absolutely necessary

to improve spray performance. Optimal spray

performance should be acheived simply by adjusting

the various controls on the unit.

To Prepare the Material:

1. Stir the spraying material thoroughly.

2. Unscrew the cup from the nozzle.

3. After the material has been properly thinned and

strained, ll the container to desired level.

Thinning the material:

For certain spraying situations or desired nishes,

thinning the material may be desired. It is not necessary

for most materials when used with the White Spray Gun.

For use with the Yellow Spray Gun thinning may be

needed to acheive a ner nish. Make sure you adjust

the Air Pressure and Material Flow settings for your

specic material needs.

If thinning is necessary, use the proper solvent as

specied by the material manufacturer. Never exceed

the thinning advice given by the coating manufacturer.

Do not thin with materials that have

a ashpoint below 100°F (38°C). The

material ashpoint should be shown on

the material container.

English

Assembly

Before you begin:

NEVER point the spray gun at

any part of the body.

Note: Your unit includes two spray guns. See below to

determine the correct spray gun for your spraying project.

Yellow spray gun - designed for spraying thinner materials,

such as oil-based stains and thinned paints. The yellow spray

gun leaves a smooth nish.

White spray gun - designed for spraying thicker materials,

such as latex paints and stains. Spraying with this gun will

leave a slightly coarser nish that is between a roller and ne-

nish sprayer.

Note: These two spray guns have dierent spray pattern

/ width controls. Make sure to familiarize yourself with

the controls on each spray gun head. See the “Controls”

section, page 8-9.

To Assemble:

IMPORTANT: Make sure the power cord is unplugged.

1. Insert the suction tube into the intake opening.

2. Align the suction tube -

a. If you are going to be spraying in a downward

direction, the angled end of the suction tube should

be pointing toward the front of the gun.

b. If you are going to be spraying in an upward direction,

the angled end of the suction tube should be pointing

toward the rear of the gun.

Note: Make sure the suction tube is inserted as far as it will

go to ensure a tight t.

3. Carefully screw the cup back onto the spray gun

assembly. Tighten rmly.

English

Assembly (continued)

4. Align the arrow on the spray gun with the “unlock”

symbol on the spray gun handle.

5. Insert and twist the spray gun into the handle toward the

“lock” symbol on the spray gun handle.

The tab below the trigger will lock the two pieces into

place.

6. Insert the air hose tightly into the connection on the

spray handle. The connection can be positioned as

desired.

7. Insert the air hose tightly into the connection into the

turbine. The connections can be positioned as desired.

English

Air and Material Controls

Spray performance will depend upon a number of

factors: material thickness, spray pattern selected,

material volume, and air pressure. With any type

of air-assisted spraying, desired spray results will

be achieved through some trial and error while

adjusting some or all of these variables.

Review these pages to learn about the spray controls

and how they can be used to acheive the desired

spray results.

Air Pressure Control Dial

The air pressure control dial adjusts the level of air

pressure produced by the turbine. The air pressure

control dial is factory-set at maximum out of the

box.

• A high air pressure level will result in a smoother

nish.

• Lowering the air pressure will result in larger

drops of material being sprayed from the gun,

and will create a slightly rougher nish.

Tip: The thicker the material you are spraying, the

higher the turbine pressure you will need.

Tip: For ne-nish work with thinner materials, you

may want to decrease the air pressure. Spraying

a thinner material at high air pressure will result in

more overspray. Overspray is sprayed material that

does not stick to the spray surface and bounces

back.

Material Flow Adjustment

The material ow adjustment controls the amount

of spray material that is sprayed from the spray gun.

• For thicker materials, it is recommended that

you start with the highest material ow setting

and then gradually decrease the ow to suit

your particular spraying needs.

• For thinner materials, it is recommended that

you start with a low material ow setting, and

then gradually increase the ow to suit your

particular spraying needs.

• The higher the ow setting, the quicker you will

have to work in order to avoid drips and sags in

your spray pattern.

Set the material volume by turning the knob on the

trigger of the spray gun.

Tip: Spraying with the knob set too high will result

in a spray pattern that runs and sags (too much

material).

Tip: Spraying with the regulator set too low will

result in a spray pattern that does not cover (not

enough material).

English

Spray Pattern Adjustment

Adjust Spray Shape - both guns

The spray pattern shape is adjusted by turning the

adjustment ring (white gun) or air cap ears (yellow

gun) to either the vertical, horizontal, or diagonal

positions. The positions of the air cap and the

corresponding spray pattern shapes are illustrated

below.

Test each pattern and use whichever pattern is

suitable for your application.

NEVER trigger the gun while

adjusting the ears on the air cap.

NEVER point the spray gun at any

part of the body.

YellowWhite

Adjustment ring

Air cap ears

Horizontal pattern



Use ‘up and down’

spraying motion

Vertical pattern



Use ‘side to side’

spraying motion

Diagonal pattern*



Use ‘up and down’ or

‘side to side’ spraying

motion



Use lower air power /

material ow



For coating smaller

areas, corners and edges

*Note: The air cap can be set diagonally on the

yellow gun only. To achieve a round pattern

with the white gun, see the “Adjust Spray Width”

section.

Adjust Spray Width - white gun only

The spray width lever on the white gun determines

the width of the spray pattern.

Spray width lever

Wide

pattern



For coating large surfaces



Use higher air power



Use higher material ow

Narrow

(round)

pattern



For coating smaller areas,

corners and edges



Use lower air power



Use lower material ow

Tips:

1. Start with a fan pattern for painting trim work

(1-5” width) and larger surfaces like doors and

walls (>5” width).

2. Adjust Material & Air Flow settings based on

coating, fan pattern width, and nozzle.

3. Fine tune the Material and Air Power settings to

achieve the best results for your application.

4. Use narrow pattern for detailed work, touch up.

5. Recommended settings for Material and Air

Power may change if the coating is thinned.

English

Proper Spraying Technique

STOP

The room you are spraying must be

properly masked in order to prevent

overspray from covering woodwork,

oors or furnishings. Make sure you

have properly masked the room per the

instructions on the enclosed “Taping

Guide”.

If spraying with an air-assisted spray system is new

or unfamiliar to you, it is advisable to practice on a

piece of scrap wood or cardboard before beginning

on your intended workpiece and/or test with water.

Surface Preparation

All objects to be sprayed should be thoroughly

cleaned before spraying material on them. Areas

not to be sprayed may, in certain cases, need to be

masked or covered.

Spray Area Preparation

The spray area must be clean and free of dust in

order to avoid blowing dust onto your freshly

sprayed surface.

How to Spray Properly

STOP

It is important to keep your arm moving

whenever the gun is being triggered. If

you pause or linger in one spot too long,

too much material will be sprayed to the

surface.

• Position the spray gun perpendicular to and

six (6) or more inches from the spray surface,

depending upon the spray pattern size desired.

With reduced material ow and air power, you

can get closer to the spraying surface.

• Spray parallel to the surface with smooth passes

at a consistent speed as illustrated below.

Doing this will help avoid irregularities in the

nish (i. e. runs and sags).

6 - 8 inches

Correct

Even coat throughout

Keep stroke smooth and at an even speed

• Always apply a thin coat of material on the rst

pass and allow to dry before applying a second,

slightly heavier coat.

• When spraying larger surfaces, overlap each

spray pass by at least 50% This will ensure full

coverage.

• When spraying, always trigger the spray gun

after spray pass has begun and release trigger

before stopping the pass. Always keep the

gun pointed squarely at the spray surface and

overlap passes slightly to obtain the most

consistent and professional nish possible.

Incorrect

Do not ex wrist while spraying.

Light coat Heavy coat Light coat

Note: When you quit spraying for any length of

time, turn the turbine OFF and place the spray

gun into the spray gun holder on the turbine.

When you restart, wipe the nozzle with a damp

cloth to remove any dried paint.

English

Proper Spraying Technique

Pattern Examples

Use the images and guidelines below in order to

assist you in achieving the desired spray pattern for

your project. These are meant to be general starting

points - you may have to slightly modify certain

controls on the system in order to get the exact

performance you need.

Large Surface Projects

Generally, high material ow and air power are

needed for spraying large surface areas, such as walls

and decks.

The white spray gun is ideal for these applications and

is designed for broad coverage in either horizontal or

vertical spraying.

• The air cap position will determine the

movement direction of the spray gun.

Small Surface Projects

Generally, low material ow and air power are

needed for spraying smaller surface areas, such as

corners, lattice, or spindles.

For this type of project, reduce power, material ow

and switch to a narrow width when using the white

gun.

The yellow spray gun provides an even narrower

pattern for smaller surface projects and ne

nishing. Moving closer to the spray surface

narrows the fan and moving farther away widens it.

• If you feel the material is going on too thin,

increase the material ow.

• If you feel the material is going on too thick,

decrease the material ow even further or move

the spray gun further away from the surface.

Note: If after following the guidelines on

these two pages you are still not getting the

spray performance you need, refer to the

‘Troubleshooting’ section on page 16.

Besides adjusting the controls, other factors that

should be considered when spraying:

• Distance from the spray object - if you are too

far from the spraying surface, the material will

go on too thin, and vice versa.

• Material thickness - if the spray pattern runs

and/or is too splotchy, the material may need to

be thinned.

Note: Only thin the material if absolutely

necessary to improve spray performance. Optimal

spray performance should be acheived simply by

adjusting the various controls on the unit.

• Spray gun movement - moving the gun too

quickly will cause the spray pattern to be too

thin and excess overspray. Moving the gun too

slowly will cause the spray pattern to be too

coarse or thick.

English

Cleanup

Flushing the unit

Before you begin:

When cleaning, use the appropriate cleaning solution (warm,

soapy water for latex materials; mineral spirits for oil-based

materials)

IMPORTANT: Never clean air cap or air holes in the

nozzle with sharp metal objects. Do not use solvents or

lubricants containing silicone.

Special cleanup instructions for use with

flammable solvents (must have a flashpoint

above 100ºF (38ºC):

 • Alwaysushspraygunoutside.

 • Areamustbefreeofammablevapors.

 • Cleaningareamustbewell-ventilated.

 • Donotsubmergeturbine!

To Flush the Unit:

1. Unplug the power cord. Loosen the material container

by 1/2 turn, but do not remove it. This will relieve any

pressure left over in the system.

Pull the trigger so that the material inside the spray

nozzle drains back into the container.

2. Unscrew the container and remove. Empty any

remaining material back into the material container.

3. Pour a small amount of the appropriate cleaning solution

into the cup (Water=1/2 full. Mineral spirits=1/4 full).

4. Attach the cup to the nozzle and plug in the sprayer.

5. Spray the cleaning solution into a safe area.

While spraying, gently shake the spray gun. This slight

agitation will help break up smaller particles of spray

material.

6. Unplug the power cord. Loosen the material container

by 1/2 turn, but do not remove it. This will relieve any

pressure left over in the system.

Pull the trigger so that the material inside the spray

nozzle drains back into the container.

IMPORTANT: If you cleaned the sprayer using mineral

spirits, repeat steps 1-6 using warm, soapy water.

Move on to “Cleanup - Cleaning the Nozzle”, next page.

1/2

PULL

Empty waste

container

English

Cleanup (continued)

Cleaning the Gun

To Clean the Spray Gun:

1. Make sure power cord is unplugged. Remove the air

hose from the rear of the spray gun handle.

2. White gun only -

a. Remove the adjustment ring (a) carefully from the

connecting nut (b). Loosen the connecting nut.

b. Remove the parts as shown. Clean all parts with a

cleaning brush and the appropriate cleaning solution.

c. Clean the air vent (c) on the suction tube with a soft

bristled cleaning brush.

To reassemble, see the instructions on the next page.

3. Yellow gun only -

a. Unscrew the nut and remove the air cap and nozzle.

Remove the parts as shown*. Clean all parts with a

cleaning brush and the appropriate cleaning solution.

Reassemble all parts when clean**.

4. Push the tab below the trigger, twist and separate the

spray gun from the handle.

Clean the rear of the nozzle (d) with the appropriate

cleaning solution. Use a thin layer of petroleum jelly to

lubricate the O-ring (e).

(a)

(b)

(c)

(d)

(e)

Nozzle seal (Yellow gun only)

(*) The nozzle seal may

become stuck inside the

yellow spray gun when the

nozzle is removed. If this

occurs, make sure to pull it

out.

(**) It is important that the nozzle

seal inside the nozzle be re-installed

properly. Make sure the cup side of

the seal (the side with the groove) is

facing out towards the front of the

nozzle. Improper installation will cause

leakage and damage to the turbine.

Groove

English

Reassembly

To Reassemble:

1. Insert the nozzle (1). Make sure to align the groove (a)

and notch (b) and align the nozzle opening with the

needle.

Note: Make sure the red nozzle seal is in place. Replace if it

falls out and is undamaged. Make sure the cup side of the

seal (the side with the groove) is facing out (c).

2. Put the air screen (d) in the air cap (e). Put both

(2)

on the

nozzle

(1)

and secure with the connecting nut

(3)

Note: This step is easier if the nozzle is facing up.

3. Snap the adjustment ring

(4)

into the connecting nut

(3)

enabling the adjustment lever (f) on the peg (g) to be

positioned in the air cap.

Note: Make sure that the two recesses on the adjustment

ring are engaged in the air cap tabs.

4. Reassemble the spray gun.

Note: Make sure the air valve tube is free of paint. If not,

clean the air valve tube by following the instructions on

the next page. If clean, make sure it is attached securely at

both ends (see inset).

(d)

(e)

(g)

(f)

(a)

(c)

(b)

Groove

English

Maintenance

Cleaning the Filters:

IMPORTANT: Before every use, you should

inspect the air lters in the turbine to see if it

is excessively dirty. If it is dirty, follow these

steps to replace it.

IMPORTANT: Never operate your unit

without the air lters. Dirt could be sucked in

and interfere with the function of the unit.

1. Press the tabs on each side of the turbine to

remove the lter covers.

2. Remove the dirty lters from the turbine and

replace with new ones. The smooth side of the

air lter must be placed toward the turbine.

Secure the covers back onto the turbine.

Cleaning the Air Valve Tube - white gun only:

Note: If paint has entered the air tube, proceed as

follows.

1. Pull the air tube (a) at the top from the nozzle. Screw

o the valve cover (b). Remove the valve seal (c). Clean

all the parts carefully.

IMPORTANT: The air tube and valve seal (c) are only

solvent-resistant to a limited extent. Do not immerse

in solvent, only wipe.

2. Place the valve seal (c) in the valve cover (b) with the

pin facing into the tube.

Note: Installing the valve seal into the valve cover will

be much easier if the valve cover is inverted.

3. Turn the nozzle upside down and screw on the valve

cover (with valve seal inside) from underneath.

Note: Turning the nozzle upside down will prevent

the valve seal from falling out of the valve cover during

reinstallation.

4. Place the air tube on the valve cover and on the nipple

at the nozzle.

(a)

(b)

(c)

(b)

English

Troubleshooting

PROBLEM CAUSE SOLUTION

Problem A: Little or no

material ow

1. Nozzle clogged.

2. Suction tube clogged.

3. Material ow setting too low.

4. Suction tube loose.

5. Air vent on suction tube blocked.

6. No pressure build up in container.

7. Air valve tube disconnected.

8. Air lter clogged.

9. Spray material too thick.

1. Clean.

2. Clean.

3. Increase material ow setting.

4. Remove and replace as tightly

as possible.

5. Clean (see page 15)

6. Tighten container.

7. Reconnect both ends of the air

tube.

8. Change

9. Thin*.

Problem B: Material

leaking

1. Nozzle loose.

2. Nozzle worn.

3. Nozzle seal missing or worn.

4. Material build-up on air cap and

nozzle

1. Tighten.

2. Replace.

3. Replace the nozzle.

4. Clean.

Problem C: Spray pattern

too thick, runs and sags

1. Material ow setting too high.

2. Air power setting too low.

3. Applying too much material.

4. Nozzle clogged.

5. Air lter clogged.

6. Too little pressure build-up in

container.

7. Spray material too thick.

1. Decrease material ow setting.

2. Increase air power setting.

3. Adjust material ow or increase

movement of spray gun.

4. Clean.

5. Change.

6. Tighten container.

7. Thin*.

Problem D: Spray jet

pulsates

1. Material in container running out.

2. Air lter clogged.

3. Air valve tube disconnected.

1. Rell.

2. Change.

3. Reconnect both ends of the air

tube.

Problem E: Too much

overspray

1. Gun too far from spray object.

2. Air power setting too high.

1. Reduce distance (6”-8” is ideal).

2. Decrease air power setting.

Problem F: Pattern is very

light and splotchy

1. Moving the spray gun too fast.

2. Material ow setting too low.

3. Air power setting too high.

1. Adjust material ow or de-

crease movement of spray gun.

2. Increase material ow setting.

3. Decrease air power setting.

This unit contains no servicable electrical parts. Do

not attempt to service yourself. Store indoors with

the cord wrapped around the turbine handle.

Have you tried the recommendations above and are still

having problems? In the United States, to speak to a

customer service representative, call our Technical Service

at 1-800-328-8251. See www.wagnerspraytech.com in the

“Contact Us” section for Technical Service hours.

*Note: Generally, material should only need to

be thinned when using the yellow spray gun.

Only thin the material as a last resort to improve

spray performance. Optimal spray performance

should be acheived simply by adjusting the

various controls on the unit.

English

Parts List • Liste de pièces • Lista de piezas

EnglishFrançaisEspañol

# Part No.

Nº de piéce

Pieza No.

English

Description

Français

Description

Español

Descripción

Qty.

Qte.

Cant.

1 -------

Turbine (includes

item 2)

Turbine (inclut de pièce 2)

Turbina (incluye le

articulo 2)

2 2307279 Filter Filtre Filtro 2

3 0414219 Air hose Tuyau d’air Manguera de aire 1

4 2303300 Turbine handle Poignée de pistolet Asa de pistola 1

Replacement parts available by calling

customer service

On peut obtenir des pièces de rechange

en appelant le Service à la clientèle.

Los repuestos están disponibles

llamanado al servicio a clientes.

1-800-328-8251

Manufacturing Code Location

Emplacement du code de fabrication

Ubicación del código de fábrica

EspañolFrançaisEnglish

Parts List • Liste de pièces • Lista de piezas

White spray gun • Pistola blanc • Pistola blanco

# Part No.

Nº de piéce

Pieza No.

English

Description

Français

Description

Español

Descripción

Qty.

Qte.

Cant.

1 0529014 Spray gun assembly

(includes items 1-8)

Ensemble de pistolet (inclut

des pièces 1 à 8)

Ensamblaje de pistola

(incluye los articulos 1-8)

2 -------- Nozzle seal

Joint d’étanchéité de buse

Sello de boquilla 1

3 0529262 Air cap kit (includes

item 2)

Trousse de chapeau d’air

(inclut de pièce 2)

Juego de tapa de aire

(incluye la articulo 2)

4 0529225 Spray jet kit Trousse de buse de

pulvérisation

Kit de chorro de

pulverización

5 0529005 Tube / Valve seal Tube / Joint de clapet Tube / Junta de la válvula 1

6 0417474 Seal Joint Sello 1

7 0417473 Suction tube Tube d’aspiration Tubo de succión 1

8 2303366 Material container Réservoir de liquide Recipiente 1

EnglishFrançaisEspañol

Parts List • Liste de pièces • Lista de piezas

# Part No.

Nº de piéce

Pieza No.

English

Description

Français

Description

Español

Descripción

Qty.

Qte.

Cant.

1 0417700A Yellow spray gun assembly

(includes items 1-5)

Ensemble de pistolet jaune

(inclut des pièces 1 à 5)

Ensamblaje de pistola

amarillo (incluye los

articulos 1-5)

2 0414353 Nozzle seal Joint d’étanchéité de

embout

Sello de boquilla 1

3 0417349 Nozzle Embout Boquilla 1

4 0414368 Air cap Chapeau d’air Tapa de aire 1

5 0414351 Connecting nut Écrou d’assemblage Tuerca de conexión 1

6 0417341 Container seal Joint d’étanchéité de

réservoir

Sello de recipiente 1

7 0414363 Suction tube Tube d’aspiration Tubo de succión 1

8 0414313 Material container (600 ml) Réservoir de liquide (600 ml) Recipiente (600 ml) 1

Yellow spray gun • Pistola jaune • Pistola amarillo

Replacement parts available by calling

customer service

On peut obtenir des pièces de rechange

en appelant le Service à la clientèle.

Los repuestos están disponibles

llamanado al servicio a clientes.

1-800-328-8251

EspañolFrançaisEnglish

Limited Warranty - HVLP paint spray equipment

This product, manufactured by Wagner Spray Tech

Corporation (Wagner), is warranted against defects

in material and work-manship for one year following

date of purchase if operated in accordance with

Wagner’s printed recommendations and instructions.

This warranty does not cover damage resulting from

improper use, accidents, user’s negligence or normal

wear. This warranty does not cover any defects or

damages caused by service or repair performed by

anyone other than a Wagner Authorized Service

Center.

ANY IMPLIED WARRANTY OF MERCHANTABILITY OR

FITNESS FOR A PARTICULAR PURPOSE IS LIMITED TO

one year FOLLOWING DATE OF PURCHASE. WAGNER

SHALL NOT IN ANY EVENT BE LIABLE FOR ANY

INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY

KIND, WHETHER FOR BREACH OF THIS WARRANTY

OR ANY OTHER REASON. THIS WARRANTY DOES NOT

APPLY TO ACCESSORIES.

THIS PRODUCT IS DESIGNED FOR HOME USAGE ONLY.

IF USED FOR COMMERCIAL OR RENTAL PURPOSES,

THIS WARRANTY APPLIES ONLY FOR 30 DAYS FROM

DATE OF PURCHASE.

If any product is defective in material and/or

workmanship during the applicable warranty period,

return it with proof of purchase, transportation

prepaid to any Wagner Authorized Service Center.

(Service Center listing is enclosed with this product.)

Wagner’s Authorized Service Center will either repair

or replace the product (at Wagner’s option) and return

it to you, postage prepaid.

SOME STATES DO NOT ALLOW LIMITATIONS ON

HOW LONG AN IMPLIED WARRANTY LASTS OR THE

EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL

DAMAGES, SO THE ABOVE LIMITATION AND

EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY

GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY

ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE

TO STATE.

Garantie limitée - Pulvérisateur de peinture HVLP

Cet article fabriqué par Wagner Spray Tech

Corporation (Wagner) est garanti contre tout défaut

de fabrication et de matériaux pour une période

d’un an suivant la date d’achat, à condition qu’il soit

utilisé conformément aux recommandations et aux

instructions écrites de Wagner. La garantie ne couvre

pas les dommages résultant d’un mauvais emploi, d’un

accident, d’une négligence de la part de l’utilisateur

ou de l’usure normale de l’article. Elle ne couvre pas

non plus les défauts ou les dommages découlant

de services d’entretien ou de réparations assurées

par tout autre établissement qu’un centre de service

après-vente agrée de Wagner.

TOUTE GARANTIE TACITE RELATIVE AUX QUALITÉS

MARCHANDES OU À L’UTILISATION DE CE PRODUIT

DANS UN BUT PARTICULIER N’EST VALABLE QUE

POUR UNE PÉRIODE D’UN AN À COMPTER DE LA

DATE D’ACHAT. WAGNER NE SAURAIT ÊTRE TENU

RESPONSABLE DES DOMMAGES FORTUITS OU

INDIRECTS QUELS QU’ILS SOIENT, QUE CE SOIT POUR

INOBSERVATION DE LA PRÉSENTE GARANTIE OU POUR

TOUTE AUTRE RAISON. LA GARANTIE NE COUVRE PAS

LES ACCESSOIRES.

CET ARTICLE A ÉTÉ CONÇU EXCLUSIVEMENT EN VUE

D’UN USAGE DOMESTIQUE. LA GARANTIE NE SERA

VALABLE QUE POUR 30 JOURS À COMPTER DE LA

DATE D’ACHAT DE L’ARTICLE EST UTILISÉ À DES FINS

COMMERCIALES OU DE LOCATION.

Tout article comportant des défauts de fabrication

ou de matériaux au cours de la période de garantie

applicable peut être retourné en port payé à un centre

de service après-vente agrée de Wagner, accompagné

de la preuve d’achat (une liste des centres de service

après-vente accompagne cet article). Le centre de

service après-vente agrée de Wagner vous renverra

l’article en port payé, après l’avoir réparé ou remplacé

(ce choix étant à la discrétion de Wagner).

COMME LES LIMITES DE TEMPS RELATIVES À UNE

GARANTIE TACITE OU À L’EXCLUSION DES DOMMAGES

DE NATURE FORTUITE OU INDIRECTE N’ONT PAS

NÉCESSAIREMENT COURS DANS TOUTES LES

PROVINCES, IL SE PEUT QUE LESDITES LIMITES OU

EXCLUSIONS NE VOUS CONCERNENT PAS. CERTAINS

DROITS PARTICULIERS VOUS SONT DÉVOLUS EN

VERTU DE LA PRÉSENTE GARANTIE ET PEUVENT

S’ACCOMPAGNER D’AUTRES DROITS EN FONCTION DE

LA PROVINCE OÙ VOUS RÉSIDEZ.

Garantía limitada - Equipo de atomización de

pintura HVLP

Este producto, fabricado por la Wagner Spray Tech

Corporation (Wagner), está garantizado contra

defectos de materiales y de mano de obra por un

año a partir de la fecha de compra siempre y cuando

se utilice de acuerdo con las recomendaciones e

intrucciones impresas de Wagner. Esta garantía

no cubre daños ocasionados por el uso incorrecto,

accidentes, negligencia por parte del usario o el

desgaste normal. Esta garantía no cubre cualquier

defecto o daño ocasionado por el servicio o las

reparaciones llevadas a cabo fuera de un Centro de

Servicio Wagner Autorizado.

CUALQUIER GARANTÍA IMPLÍCITA RFERENTE AL

POTENCIAL COMERCIAL O ADAPTABILIDAD pARA

UN USO PARTICULAR SE LIMITA A UN AÑO A PARTIR

DE LA FECHA DE COMPRA. WAGNER EN NINGÚN

CASO SERÁ RESPONSABLE DE CUALQUIER DAÑO

DIRECTO O INDIRECTO DE CUALQUIER TIPO, YA SEA

POR VIOLACIÓN DE ESTA GARANTÍA O CUALQUIER

OTRA RAZÓN. ESTA GARANTÍA NO SE APLICA A LOS

ACCESORIOS.

ESTE PRODUCTO ESTÁ DISEÑADO PARA SER

UTILIZADO EN EL HOGAR ÚNICAMENTE. SI SE UTILIZA

PARA PROPÓSITOS COMERCIALES O DE ALQUILER,

ESTÁ GARANTÍA ES VÁLIDA ÚNICAMENTE DURANTE 30

DÍAS A PARTIR DE LA FECHA DE COMPRA.

Si cualquier producto está defectuoso con respecto a

los materiales o mano de obra, regréselo porte pagado

junto con el recibo de compra a cualquier Centro de

Servicio Wagner Autorizado (la lista de Centros de

Servicio se adjunta con este producto). El Centro de

Servicio Wagner Autorizado reparará o reemplazará el

producto (a la discreción de Wagner) y se lo regresará

porte pagado.

ALGUNOS ESTADOS, DEPARTAMENTOS O PROVINCIAS

NO PERMITEN LIMITACIONES EN CUANTO AL PERÍODO

DE VALIDEZ DE UNA GARANTÍA IMPLÍCITA NI LA

EXCLUSIÓN DE DAÑOS DIRECTOS O INDIRECTOS. POR

LA TANTO, LA LIMITACIÓN Y LA EXCLUSIÓN ANTERIOR

PUEDEN NO APLICARSE A USTED.

ESTA GARANTÍA LE OTORGA DERECHOS LEGALES

ESPECÍFICOS Y USTED TAMBIÉN PUEDE TENER OTROS

DERECHOS QUE VARÍAN DE UNA LOCALIDAD A OTRA.

WAGNER PaintREADY System® Manuel utilisateur

Marque: WAGNER

Modèle: PaintREADY System®

Catégorie: Systèmes de pulvérisation fine Power

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: WAGNER PaintREADY System® User manual

Documents connexes

Autres documents

Titan Flexspray Handheld Le manuel du propriétaire