Pioneer DEH-2600UI Manuel utilisateur

Black plate (1,1)

Owner’s Manual

Mode d’emploi

Manuale d’istruzioni

Manual de instrucciones

Bedienungsanleitung

Handleiding

Руководство пользователя

CD RDS RECEIVER

AUTORADIO CD RDS

SINTOLETTORE CD RDS

REPRODUCTOR DE CD CON RECEPTOR RDS

CD RDS-EMPFÄNGER

CD RDS-ONTVANGER

CD RDS ПРИЕМНИК

DEH-X3600UI

DEH-2600UI

<QRD3200-A>1

English NederlandsDeutschEspañolItalianoFrançais Русский

Black plate (2,1)

Thank you for purchasing this PIONEER

product

To ensure proper use, please read through this

manual before using this product. It is especially

important that you read and observe WARN-

INGs and CAUTIONs in this manual. Please

keep the manual in a safe and accessible place for

future reference.

If you want to dispose this product, do not

mix it with general household waste. There is

a separate collection system for used elec-

tronic products in accordance with legislation

that requires proper treatment, recovery and

recycling.

Private households in the member states of the

EU, in Switzerland and Norway may return their

used electronic products free of charge to desig-

nated collection facilities or to a retailer (if you

purchase a similar new one).

For countries not mentioned above, please con-

tact your local authorities for the correct method

of disposal.

By doing so you will ensure that your disposed

product undergoes the necessary treatment, re-

covery and recycling and thus prevent potential

negative effects on the environment and human

health.

About this unit

The tuner frequencies on this unit are allocated

for use in Western Europe, Asia, the Middle

East, Africa and Oceania. Use in other areas

may result in poor reception. The RDS (radio

data system) function only works in areas that

broadcast RDS signals for FM stations.

WARNING

! Do not attempt to install or service this

product by yourself. Installation or serv-

icing of this product by persons without

training and experience in electronic

equipment and automotive accessories

may be dangerous and could expose you

to the risk of electric shock, injury or

other hazards.

! Do not attempt to operate the unit while driv-

ing. Make sure to pull off the road and park

your vehicle in a safe location before at-

tempting to use the controls on the device.

CAUTION

! Do not allow this unit to come into contact

with liquids. Electrical shock could result.

Also, damage to this unit, smoke, and over-

heating could result from contact with

liquids.

! The Pioneer CarStereo-Pass is for use only in

Germany.

! Always keep the volume low enough to hear

outside sounds.

! Avoid exposure to moisture.

CAUTION

This product is a class 1 laser product classi-

fied under the Safety of laser products, IEC

60825-1:2007.

If you experience problems

Should this unit fail to work properly, please con-

tact your dealer or nearest authorized PIONEER

Service Station.

Before you start

2

Section

Before you start

En

01

<QRD3200-A>2

Black plate (3,1)

Head unit

DEH-X3600UI

2 4

6

5

3

d8 9 e

7

a

b c

1

DEH-2600UI

62 4 5

3

1

8

9 de

7

b

c

a

1 SRC/OFF

2 h (eject)

3 MULTI-CONTROL (M.C.)

4

(list)

5 Disc loading slot

6 USB port

7

MIX (MIXTRAX)

DEH-X3600UI

iPod

DEH-2600UI

8 BAND/

(iPod control)

9

(back)/DIMMER (dimmer)

a c/d

b DISP

c 1/

to 6/

d AUX input jack (3.5 mm stereo jack)

e Detach button

CAUTION

Use an optional Pioneer USB cable (CD-U50E)

to connect the USB storage device as any device

connected directly to the unit will protrude out

from the unit, which could be dangerous.

Display indication

DEH-X3600UI

1

7 b9

6 8 a

54

2

3

DEH-2600UI

43 7 a8

21

b 6 5 9

1

Main information section

! Tuner: band and frequency

! RDS: program service name, PTY infor-

mation and other literal information

! CD player, USB storage device and iPod:

elapsed playback time and text informa-

tion

2

Appears when a lower tier of folder or menu

exists.

3

(list)

4 Sub information section

5 LOC (local seek tuning)

6 TP (traffic program identification)

7 TA (traffic announcements)

8

(sound retriever)

9

(random/shuffle)

a

(repeat)

b

(iPod control)

This unit’s iPod function is operated from

your iPod.

Set up menu

1 After installation of this unit, turn the

ignition switch to ON.

SET UP appears.

2 Turn M.C. to switch to YES.

# If you do not use the unit for 30 seconds, the set

up menu will not be displayed.

# If you prefer not to set up at this time, turn M.C.

to switch to NO.

3 Press M.C. to select.

4 Follow these steps to set the menu.

To proceed to the next menu option, you need to

confirm your selection.

LANGUAGE (multi-language)

This unit can display the text information from a

compressed audio file even for information em-

bedded in English, Russian or Turkish.

! If the embedded language and the selected

language setting are not the same, text infor-

mation may not display properly.

! Some characters may not be displayed prop-

erly.

1 Turn M.C. to select the desired setting.

ENG (English)—РУС (Russian)—TUR (Turk-

ish)

2 Press M.C. to confirm the selection.

CLOCK SET (setting the clock)

1 Turn M.C. to adjust hour.

2 Press M.C. to select minute.

3 Turn M.C. to adjust minute.

4 Press M.C. to confirm the selection.

FM STEP (FM tuning step)

Use FM STEP to set FM tuning step options (seek

step settings).

1 Turn M.C. to select the FM tuning step.

100 (100 kHz)—50 (50 kHz)

2 Press M.C. to confirm the selection.

QUIT appears.

! The manual tuning step is fixed at 50 kHz.

! When AF and TA are turned off, the seek step

is fixed at 50 kHz even if set to 100.

5 To finish your settings, turn M.C. to select

YES.

# If you prefer to change your setting again, turn

M.C. to switch to NO.

6 Press M.C. to select.

English

Using this unit

3

Section

Using this unit

En

02

<QRD3200-A>3

Black plate (4,1)

Notes

! You can set up the menu options from the

system menu and initial menu. For details

about the settings, refer to System menu on

page 9 and Initial menu on page 11.

! You can cancel set up menu by pressing

SRC/OFF.

Basic operations

Important

! Handle the front panel with care when re-

moving or attaching it.

! Avoid subjecting the front panel to excessive

shock.

! Keep the front panel out of direct sunlight

and high temperatures.

! To avoid damaging the device or vehicle inte-

rior, remove any cables and devices attached

to the front panel before detaching it.

Removing the front panel

1 Press the detach button to release the front

panel.

2 Push the front panel upward (M) and then pull

it toward (N) you.

3 Always store the detached front panel in a pro-

tective case or bag.

Re-attaching the front panel

1 Slide the front panel to the left.

2 Press the right side of the front panel until it is

firmly seated.

Forcing the front panel into place may result in

damage to the front panel or head unit.

Turning the unit on

1 Press SRC/OFF to turn the unit on.

Turning the unit off

1 Press and hold SRC/OFF until the unit turns

off.

Selecting a source

1 Press SRC/OFF to cycle between:

RADIO—CD—USB/iPod—APP (application)—

AUX

! USB MTP displays while the MTP connection

is in use.

! Only for DEH-2600UI

When there is an iPod connected and a source

other than iPod is selected, you can switch to

iPod by pressing iPod.

Adjusting the volume

1 Turn M.C. to adjust the volume.

Note

When this unit’s blue/white lead is connected to

the vehicle’s auto-antenna relay control termi-

nal, the vehicle’s antenna extends when this

unit’s source is turned on. To retract the anten-

na, turn the source off.

Frequently used menu

operations

Returning to the previous display

Returning to the previous list (the folder one level

higher)

1 Press

/DIMMER.

Returning to the ordinary display

Canceling the main menu

1 Press BAND/

.

Returning to the ordinary display from the list

1 Press BAND/

.

Radio

Basic operations

Selecting a band

1 Press BAND/

until the desired band (FM1,

FM2,FM3 for FM or MW/LW) is displayed.

Switching preset stations

1 Press c or d.

! Select PCH (preset channel) under SEEK to

use this function.

Manual tuning (step by step)

1 Press c or d.

! Select MAN (manual tuning) under SEEK to

use this function.

Seeking

1 Press and hold c or d, and then release.

You can cancel seek tuning by briefly pressing

c or d.

While pressing and holding c or d, you can

skip stations. Seek tuning starts as soon as

you release c or d.

Notes

! For details about SEEK, refer to SEEK (left/

right key setting) on page 5.

! This unit’s AF (alternative frequencies

search) function can be turned on and off.

AF should be off for normal tuning operation

(refer to AF (alternative frequencies search)

on page 5).

Storing and recalling stations

for each band

Using preset tuning buttons

1 To store: Press and hold down one of the

preset tuning buttons (1/

to 6/ ) until

the number stops flashing.

2 To recall: Press one of the preset tuning

buttons (1/

to 6/ ).

Using this unit

4

Section

Using this unit

En

02

<QRD3200-A>4

Black plate (5,1)

Switching the display

Selecting the desired text information

1 Press DISP to cycle between the following:

! FREQUENCY (program service name or

frequency)

! BRDCST INFO (program service name/PTY

information)

! CLOCK (source name and clock)

Notes

! If the program service name cannot be ac-

quired in FREQUENCY, the broadcast fre-

quency is displayed instead. If the program

service name is detected, the program serv-

ice name will be displayed.

! Depending on the band, text information can

be changed.

! Text information items that can be changed

depend on the area.

Using PTY functions

You can tune in to a station using PTY (program

type) information.

Searching for an RDS station by PTY information

1 Press

(list).

2 Turn M.C. to select a program type.

NEWS/INFO—POPULAR—CLASSICS—

OTHERS

3 Press M.C. to begin the search.

The unit searches for a station broadcasting

that type of program. When a station is found,

its program service name is displayed.

! To cancel the search, press M.C. again.

! The program of some stations may differ

from that indicated by the transmitted PTY.

! If no station is broadcasting the type of

program you searched for, NOT FOUND is

displayed for about two seconds and then

the tuner returns to the original station.

PTY list

For more details about PTY list, visit the follow-

ing site:

http://www.pioneer.eu/eur/products/25/121/tech/

CarAudio/PTY.html

Function settings

1 Press M.C. to display the main menu.

2 Turn M.C. to change the menu option

and press to select FUNCTION.

3 Turn M.C. to select the function.

Once selected, the following functions can be

adjusted.

# If MW/LW band is selected, only BSM, LOCAL

and SEEK are available.

FM SETTING (FM sound quality settings)

The sound quality level can be set to match the

broadcast signal conditions of the FM band sig-

nal.

1 Press M.C. to display the setting mode.

2 Turn M.C. to select the desired setting.

! STANDARD – This is the standard setting.

! HI-FI – This is the setting to use to prioritize

the high quality of stereo sound.

! STABLE – This is the setting to use to priori-

tize the low noise of monaural sound.

BSM (best stations memory)

BSM (best stations memory) automatically stores

the six strongest stations in the order of their sig-

nal strength.

1 Press M.C. to turn BSM on.

To cancel, press M.C. again.

REGIONAL (regional)

When AF is used, the regional function limits the

selection of stations to those broadcasting region-

al programs.

1 Press M.C. to turn the regional function on or

off.

LOCAL (local seek tuning)

Local seek tuning allows you to tune in to only

those radio stations with sufficiently strong sig-

nals for good reception.

1 Press M.C. to select the desired setting.

FM: OFF—LV1—LV2—LV3—LV4

MW/LW: OFF—LV1—LV2

The highest level setting allows reception of

only the strongest stations, while lower levels

allow the reception of weaker stations.

TA (traffic announcement standby)

1 Press M.C. to turn traffic announcement

standby on or off.

AF (alternative frequencies search)

1 Press M.C. to turn AF on or off.

NEWS (news program interruption)

1 Press M.C. to turn the NEWS function on or

off.

SEEK (left/right key setting)

You can assign a function to the left and right keys

of the unit.

Select MAN (manual tuning) to tune up or down

manually or select PCH (preset channel) to switch

between preset channels.

1 Press M.C. to select MAN or PCH.

CD/CD-R/CD-RW and USB

storage devices

MTP connection

MTP-compatible Android devices (running

Android OS 4.0 or higher) can be connected by

MTP connection using the USB source. To con-

nect an Android device, use the cable that came

with the device.

Notes

! This function is not compatible with MIX-

TRAX.

! This function is not compatible with WAV.

Basic operations

Playing a CD/CD-R/CD-RW

1 Insert the disc into the disc loading slot with

the label side up.

Ejecting a CD/CD-R/CD-RW

1 Press h.

Playing songs on a USB storage device

1 Open the USB port cover.

2 Plug in the USB storage device using a USB

cable.

Stopping playback of files on a USB storage de-

vice

1 You may disconnect the USB storage device at

any time.

Selecting a folder

1 Press 1/

or 2/ .

Selecting a track

1 Press c or d.

Fast forwarding or reversing

1 Press and hold c or d.

! When playing compressed audio, there is no

sound during fast forward or reverse.

Returning to root folder

1 Press and hold BAND/

.

English

Using this unit

5

Section

Using this unit

En

02

<QRD3200-A>5

Black plate (6,1)

Switching between compressed audio and CD-DA

1 Press BAND/

.

Switching between playback memory devices

You can switch between playback memory devices

on USB storage devices with more than one Mass

Storage Device-compatible memory device.

1 Press BAND/

.

! You can switch between up to 32 different

memory devices.

Note

Disconnect USB storage devices from the unit

when not in use.

Operations using the MIXTRAX

button

Turning MIXTRAX on or off

Only for DEH-X3600UI

You can use this function when USB is selected as

the source.

You cannot use this function with USB MTP.

1 Press MIX to turn MIXTRAX on or off.

! For more details about MIXTRAX, refer to

About MIXTRAX on page 10.

! When MIXTRAX is in use, the sound retriever

function is disabled.

Switching the display

Selecting the desired text information

1 Press DISP to cycle between the following:

CD-DA

! ELAPSED TIME (track number and play-

back time)

! CLOCK (source name and clock)

! SPEANA (spectrum analyzer)

CD-TEXT

! TRACK INFO (track title/track artist/disc

title)

! ELAPSED TIME (track number and play-

back time)

! CLOCK (source name and clock)

! SPEANA (spectrum analyzer)

MP3/WMA/WAV

! TRACK INFO (track title/artist name/album

title)

! FILE INFO (file name/folder name)

! ELAPSED TIME (track number and play-

back time)

! CLOCK (source name and clock)

! SPEANA (spectrum analyzer)

Selecting and playing files/

tracks from the name list

1 Press to switch to the file/track name

list mode.

2 Use M.C. to select the desired file name

(or folder name).

Selecting a file or folder

1 Turn M.C.

Playing

1 When a file or track is selected, press M.C.

Viewing a list of the files (or folders) in the se-

lected folder

1 When a folder is selected, press M.C.

Playing a song in the selected folder

1 When a folder is selected, press and hold M.C.

Operations using special buttons

Selecting a repeat play range

1 Press 6/

to cycle between the following:

CD/CD-R/CD-RW

! ALL – Repeat all tracks

! ONE – Repeat the current track

! FLD – Repeat the current folder

USB storage device

! ALL – Repeat all files

! ONE – Repeat the current file

! FLD – Repeat the current folder

Playing tracks in random order

1 Press 5/

to turn random play on or off.

Tracks in a selected repeat range are played in

random order.

! To change songs during random play, press d

to switch to the next track. Pressing c restarts

playback of the current track from the begin-

ning of the song.

Pausing playback

1 Press 4/PAUSE to pause or resume.

Enhancing compressed audio and restoring rich

sound (sound retriever)

1 Press 3/S.Rtrv to cycle between:

1—2—OFF (off)

1 is effective for low compression rates, and 2

is effective for high compression rates.

! Key operation is disabled when MIXTRAX is

on.

Function settings

1 Press M.C. to display the main menu.

2 Turn M.C. to change the menu option

and press to select FUNCTION.

Once selected, the function below can be ad-

justed.

! S.RTRV is not available when MIXTRAX is

turned on.

S.RTRV (sound retriever)

Automatically enhances compressed audio and

restores rich sound.

1 Press M.C. to select the desired setting.

For details, refer to Enhancing compressed

audio and restoring rich sound (sound retriever)

on page 6.

iPod

Basic operations

Playing songs on an iPod

1 Open the USB port cover.

2 Connect an iPod to USB input.

Playback is performed automatically.

Selecting a song (chapter)

1 Press c or d.

Selecting an album

1 Press 1/

or 2/ .

Fast forwarding or reversing

1 Press and hold c or d.

Notes

! The iPod cannot be turned on or off when the

control mode is set to

CONTROL AUDIO/CTRL AUDIO.

! Disconnect headphones from the iPod be-

fore connecting it to this unit.

! The iPod will turn off about two minutes after

the ignition is switched off.

Using this unit

6

Section

Using this unit

En

02

<QRD3200-A>6

Black plate (7,1)

Operations using the MIXTRAX

button

Turning MIXTRAX on or off

Only for DEH-X3600UI

1 Press MIX to turn MIXTRAX on or off.

! For more details about MIXTRAX, refer to

About MIXTRAX on page 10.

Switching the display

Selecting the desired text information

1 Press DISP to cycle between the following:

! TRACK INFO (track title/artist name/album

title)

! ELAPSED TIME (track number and play-

back time)

! CLOCK (source name and clock)

! SPEANA (spectrum analyzer)

Browsing for a song

1 Press to switch to the top menu of list

search.

2 Use M.C. to select a category/song.

Changing the name of the song or category

1 Turn M.C.

Playlists—artists—albums—songs—podcasts

—genres—composers—audiobooks

Playing

1 When a song is selected, press M.C.

Viewing a list of songs in the selected category

1 When a category is selected, press M.C.

Playing a song in the selected category

1 When a category is selected, press and hold

M.C.

Searching the list by alphabet

1 When a list for the selected category is dis-

played, press

to switch to alphabet search

mode.

! You also can switch to alphabet search

mode by turning M.C. twice.

2 Turn M.C. to select a letter.

3 Press M.C. to display the alphabetical list.

! To cancel searching, press

/DIMMER.

Notes

! You can play playlists created with the com-

puter application (MusicSphere). The appli-

cation will be available on our website.

! Playlists that you created with the computer

application (MusicSphere) are displayed in

abbreviated form.

Operations using special buttons

Selecting a repeat play range

1 Press 6/

to cycle between the following:

! ONE – Repeat the current song

! ALL – Repeat all songs in the selected list

! When the control mode is set to CONTROL

iPod/CTRL iPod, the repeat play range will be

same as what is set for the connected iPod.

Selecting a random play range (shuffle)

1 Press 5/

to cycle between the following:

! SNG – Play back songs in the selected list

in random order.

! ALB – Play back songs from a randomly se-

lected album in order.

! OFF – Not play back in random order.

Playing all songs in random order (shuffle all)

1 Press and hold 5/

to turn shuffle all on.

! To turn off shuffle all, select OFF in shuffle. For

details, refer to Selecting a random play range

(shuffle) on page 7.

Pausing playback

1 Press 4/PAUSE to pause or resume.

Enhancing compressed audio and restoring rich

sound (sound retriever)

1 Press 3/S.Rtrv to cycle between:

1—2—OFF (off)

1 is effective for low compression rates, and 2

is effective for high compression rates.

Playing songs related to the

currently playing song

You can play songs from the following lists.

• Album list of the currently playing artist

• Song list of the currently playing album

• Album list of the currently playing genre

1 Press and hold

to switch to link play

mode.

2 Turn M.C. to change the mode; press to

select.

! ARTIST – Plays an album by the artist cur-

rently playing.

! ALBUM – Plays a song from the album cur-

rently being played.

! GENRE – Plays an album from the genre cur-

rently being played.

The selected song/album will be played after the

currently playing song.

Notes

! The selected song/album may be canceled if

you use functions other than link search (e.g.

fast forward and reverse).

! Depending on the song selected to play, the

end of the currently playing song and the be-

ginning of the selected song/album may be

cut off.

Using this unit’s iPod function

from your iPod

This unit’s iPod function can be controlled by

using the connected iPod.

CONTROL iPod/CTRL iPod is not compatible

with the following iPod models.

! iPod nano 1st generation

! iPod with video

% Press BAND/

to switch the control

mode.

! CONTROL iPod/CTRL iPod – This unit’siPod

function can be operated from the connected

iPod.

! CONTROL AUDIO/CTRL AUDIO – This unit’s

iPod function can be controlled by using this

unit.

Only for DEH-2600UI

You can also switch the control mode by press-

ing iPod.

Notes

! Switching the control mode to

CONTROL iPod/CTRL iPod pauses song

playback. Use the iPod to resume playback.

! The following operations are still accessible

from the unit even if the control mode is set

to CONTROL iPod/CTRL iPod.

— Pausing

— Fast forward/reverse

— Selecting a song (chapter)

! The volume can only be adjusted from this

unit.

Function settings

1 Press M.C. to display the main menu.

English

Using this unit

7

Section

Using this unit

En

02

<QRD3200-A>7

Black plate (8,1)

2 Turn M.C. to change the menu option

and press to select FUNCTION.

3 Turn M.C. to select the function.

Once selected, the following functions can be

adjusted.

! AUDIO BOOK is not available when

CONTROL iPod/CTRL iPod is selected in the

control mode. For details, refer to Using this

unit’s iPod function from your iPod on page 7.

AUDIO BOOK (audiobook speed)

1 Press M.C. to display the setting mode.

2 Turn M.C. to select your favorite setting.

! FASTER – Playback at a speed faster than

normal

! NORMAL – Playback at normal speed

! SLOWER – Playback at a speed slower

than normal

S.RTRV (sound retriever)

1 Press M.C. to select the desired setting.

For details, refer to Enhancing compressed

audio and restoring rich sound (sound retriever)

on page 7.

Using connected device

applications

You can use this unit to perform streaming play-

back of and control tracks in iPhone applica-

tions or just for streaming playback.

Important

Use of third party apps may involve or require

the provision of personally identifiable infor-

mation, whether through the creation of a

user account or otherwise, and for certain ap-

plications, the provision of geolocation data.

ALL THIRD PARTY APPS ARE THE SOLE RE-

SPONSIBILITY OF THE PROVIDERS, INCLUD-

ING WITHOUT LIMITATION COLLECTION AND

SECURITY OF USER DATA AND PRIVACY

PRACTICES. BY ACCESSING THIRD PARTY

APPS, YOU AGREE TO REVIEW THE TERMS

OF SERVICE AND PRIVACY POLICIES OF THE

PROVIDERS. IF YOU DO NOT AGREE WITH

THE TERMS OR POLICIES OF ANY PROVIDER

OR DO NOT CONSENT TO THE USE OF GEO-

LOCATION DATA WHERE APPLICABLE, DO

NOT USE THAT THIRD PARTY APP.

Information for compatibility of

connected devices

The following is the detailed information regard-

ing the terminals required to use the application

for iPhone on this unit.

For iPhone users

! This function is compatible with iPhone and

iPod touch.

! The device has iOS 5.0 or higher.

Notes

! Please check our website for a list of sup-

ported iPhone applications for this unit.

! Pioneer is not liable for any issues that may

arise from incorrect or flawed app-based

content.

! The content and functionality of the sup-

ported applications are the responsibility of

the App providers.

Starting procedure for iPhone users

1 Connect an iPhone to USB input.

2 Switch the source to APP.

3 Start up the application on the iPhone

and initiate playback.

Basic operations

Selecting a track

1 Press c or d.

Fast forwarding or reversing

1 Press and hold c or d.

Pausing playback

1 Press BAND/

to pause or resume.

Switching the display

Selecting the desired text information

1 Press DISP to cycle between the following:

! TRACK INFO (track title/artist name/album

title)

! APP NAME (application name)

! ELAPSED TIME (playback time)

! CLOCK (source name and clock)

! SPEANA (spectrum analyzer)

Function settings

1 Press M.C. to display the main menu.

2 Turn M.C. to change the menu option

and press to select FUNCTION.

3 Turn M.C. to select the function.

Once selected, the following functions can be

adjusted.

PAUSE (pause)

1 Press M.C. to pause or resume.

S.RTRV (sound retriever)

1 Press M.C. to select the desired setting.

1—2—OFF (off)

1 is effective for low compression rates, and 2

is effective for high compression rates.

Audio adjustments

1 Press M.C. to display the main menu.

2 Turn M.C. to change the menu option

and press to select AUDIO.

3 Turn M.C. to select the audio function.

Once selected, the following audio functions

can be adjusted.

! FADER is not available when SUB.W/SUB.W

is selected in SP-P/O MODE. For details, refer

to SP-P/O MODE (rear output and preout set-

ting) on page 11.

! SUB.W and SUB.W CTRL are not available

when REAR/REAR is selected in

SP-P/O MODE. For details, refer to

SP-P/O MODE (rear output and preout set-

ting) on page 11.

! SUB.W CTRL is not available when SUB.W is

selected in OFF. For details, refer to SUB.W

(subwoofer on/off setting) on page 9.

! SLA is not available when FM is selected as

the source.

FADER (fader adjustment)

1 Press M.C. to display the setting mode.

2 Turn M.C. to adjust the front/rear speaker bal-

ance.

BALANCE (balance adjustment)

Using this unit

8

Section

Using this unit

En

02

<QRD3200-A>8

Black plate (9,1)

1 Press M.C. to display the setting mode.

2 Turn M.C. to adjust the left/right speaker bal-

ance.

EQ SETTING (equalizer recall)

1 Press M.C. to display the setting mode.

2 Turn M.C. to select the equalizer.

POWERFUL—NATURAL—VOCAL—CUS-

TOM1—CUSTOM2—FLAT—SUPER BASS

The equalizer band and equalizer level can be

customized when CUSTOM1 or CUSTOM2 is

selected.

If selecting CUSTOM1 or CUSTOM2, complete

the procedures outlined below. If selecting

other options, press M.C. to return to the pre-

vious display.

! CUSTOM1 can be set separately for each

source. However, USB, iPod and APP are

all set to the same setting automatically.

! CUSTOM2 is a shared setting used in com-

mon for all sources.

3 Press M.C. to display the setting mode.

4 Press M.C. to cycle between the following:

Equalizer band—Equalizer level

5 Turn M.C. to select the desired setting.

Equalizer band: 80HZ—250HZ—800HZ—

2.5KHZ—8KHZ

Equalizer level: +6 to –6

LOUDNESS (loudness)

Loudness compensates for deficiencies in the low-

frequency and high-frequency ranges at low vol-

ume.

1 Press M.C. to select the desired setting.

OFF (off)—LOW (low)—MID (mid)—HI (high)

SUB.W (subwoofer on/off setting)

This unit is equipped with a subwoofer output

which can be turned on or off.

1 Press M.C. to select the desired setting.

NOR (normal phase)—REV (reverse phase)—

OFF (subwoofer off)

SUB.W CTRL (subwoofer adjustment)

Only frequencies lower than those in the selected

range are outputted from the subwoofer.

1 Press M.C. to display the setting mode.

2 Press M.C. to cycle between the following:

Cut-off frequency—Output level—Slope level

Rates that can be adjusted will flash.

3 Turn M.C. to select the desired setting.

Cut-off frequency: 50HZ—63HZ—80HZ—

100HZ—125HZ—160HZ—200HZ

Output level: –24 to +6

Slope level: –12— –24

BASS BOOST (bass boost)

1 Press M.C. to display the setting mode.

2 Turn M.C. to select a desired level.

0 to +6 is displayed as the level is increased or

decreased.

HPF SETTING (high pass filter adjustment)

Use this function when wanting to listen only to

high-frequency sounds. Only frequencies higher

than the high-pass filter (HPF) cutoff are output

from the speakers.

1 Press M.C. to display the setting mode.

2 Press M.C. to cycle between the following:

Cut-off frequency—Slope level

3 Turn M.C. to select the desired setting.

Cut-off frequency: OFF—50HZ—63HZ—80HZ

—100HZ—125HZ—160HZ—200HZ

Slope level: –12— –24

SLA (source level adjustment)

This function prevents the volume from changing

too dramatically when the source switches.

! Settings are based on the FM volume level,

which remains unchanged.

! The MW/LW volume level can also be adjusted

with this function.

! USB, iPod and APP are all set to the same set-

ting automatically.

1 Press M.C. to display the setting mode.

2 Turn M.C. to adjust the source volume.

Adjustment range: +4 to –4

System menu

Important

PW SAVE (power saving) is canceled if the ve-

hicle battery is disconnected and will need to be

turned back on once the battery is reconnected.

When PW SAVE (power saving) is off, depend-

ing on connection methods, the unit may con-

tinue to draw power from the battery if your

vehicle’s ignition doesn’t have an ACC (acces-

sory) position.

1 Press M.C. to display the main menu.

2 Turn M.C. to change the menu option

and press to select SYSTEM.

3 Turn M.C. to select the system menu

function.

Once selected, the following system menu func-

tions can be adjusted.

! INFO DISPLAY and BRIGHTNESS are not

available for DEH-2600UI.

! MUTE MODE is not available for DEH-

X3600UI.

LANGUAGE (multi-language)

This unit can display the text information from a

compressed audio file even for information em-

bedded in English, Russian or Turkish.

! If the embedded language and the selected

language setting are not the same, text infor-

mation may not display properly.

! Some characters may not be displayed prop-

erly.

1 Press M.C. to select the desired setting.

ENG (English)—РУС (Russian)—TUR (Turk-

ish)

CLOCK SET (setting the clock)

1 Press M.C. to display the setting mode.

2 Press M.C. to select the segment of the clock

display you wish to set.

Hour—Minute

3 Turn M.C. to adjust the clock.

12H/24H (time notation)

1 Press M.C. to select the desired setting.

12H (12-hour clock)—24H (24-hour clock)

INFO DISPLAY (sub information)

The type of text information displayed in the sub

information section can be toggled.

1 Press M.C. to display the setting mode.

2 Turn M.C. to select the desired setting.

SPEANA—LEVEL METER—SOURCE—CLOCK

—OFF

! The signal bar indicator displays for SPEANA

or LEVEL METER when the source is set to

RADIO.

AUTO PI (auto PI seek)

The unit can automatically search for a different

station with the same programming, even during

preset recall.

1 Press M.C. to turn Auto PI seek on or off.

AUX (auxiliary input)

English

Using this unit

9

Section

Using this unit

En

02

<QRD3200-A>9

Black plate (10,1)

Activate this setting when using an auxiliar y de-

vice connected to this unit.

1 Press M.C. to turn AUX on or off.

DIMMER (dimmer)

1 Press M.C. to turn the dimmer on or off.

! You can also change the dimmer setting by

pressing and holding

/DIMMER.

BRIGHTNESS (brightness adjustment)

You can use this setting to adjust the display

brightness.

The range of settings available for BRIGHTNESS

will vary depending on whether DIMMER is on or

off. For details, refer to DIMMER (dimmer) on page

10.

1 Press M.C. to display the setting mode.

2 Turn M.C. to select the desired setting.

DIMMER on: 1 to 4

DIMMER off: 1 to 5

MUTE MODE (mute mode)

Sound from this system is automatically muted or

attenuated when a signal from equipment with a

mute function is received.

1 Press M.C. to display the setting mode.

2 Turn M.C. to select the desired setting.

! MUTE – Muting

! 20dB ATT – Attenuation (20dB ATT has a

stronger effect than 10dB ATT)

! 10dB ATT – Attenuation

PW SAVE (power saving)

Switching this function on enables you to reduce

the consumption of battery power.

! Turning on the source is the only operation al-

lowed when this function is on.

1 Press M.C. to turn the power save on or off.

Selecting the illumination color

Only for DEH-X3600UI

Illumination function menu

1 Press M.C. to display the main menu.

2 Turn M.C. to display ILLUMI and press to

select.

3 Turn M.C. to select the illumination func-

tion.

Once selected, the following audio functions

can be adjusted.

KEY COLOUR (key section color setting)

You can select desired colors for the keys of this

unit.

1 Press M.C. to display the setting mode.

2 Turn M.C. to select the illumination color.

! Preset colors (ranging from WHITE to

BLUE)

! SCAN (cycle through a variety of colors au-

tomatically)

! CUSTOM (customized illumination color)

DISP COLOUR (display section color setting)

You can select the desired colors for the display of

this unit.

1 Press M.C. to display the setting mode.

2 Turn M.C. to select the illumination color.

! Preset colors (ranging from WHITE to

BLUE)

! SCAN (cycle through a variety of colors au-

tomatically)

! CUSTOM (customized illumination color)

BOTH COLOUR (key and display color setting)

You can select the desired colors for the keys and

display of this unit.

1 Press M.C. to display the setting mode.

2 Turn M.C. to select the illumination color.

! Preset colors (ranging from WHITE to

BLUE)

! SCAN (cycle through a variety of colors au-

tomatically)

ILLUMI FX (illumination effect mode)

In this mode, an illumination effect can be seen

on the display at certain times such as when the

ACC power is turned on/off or a CD is inserted/

ejected.

1 Press M.C. to turn ILLUMI FX on or off.

! The illumination effect will activate when the

ACC power is turned on/off regardless of

whether the ILLUMI FX setting is on or off.

Note

When CUSTOM is selected, the customized

color saved is selected.

Customizing the illumination color

You can create custom illumination colors for

both KEY COLOUR and DISP COLOUR.

1 Press M.C. to display the main menu.

2 Turn M.C. to display ILLUMI and press to

select.

3 Turn M.C. to display KEY COLOUR or

DISP COLOUR. Press to select.

4 Press M.C. and hold until the customizing

illumination color setting appears in the dis-

play.

5 Press M.C. to select the primary color.

R (red)—G (green)—B (blue)

6 Turn M.C. to adjust the brightness level.

Adjustment range: 0 to 60

# You cannot select a level below 20 for all three of

R (red), G (green), and B (blue) at the same time.

# You can also perform the same operation on

other colors.

Note

You cannot create a custom illumination color

while SCAN is selected.

About MIXTRAX

Only for DEH-X3600UI

MIXTRAX technology is used to insert a variety

of sound effects in between songs, allowing you

to experience your music as a nonstop mix com-

plete with visual effects.

Notes

! Depending on the file/song, sound effects

may not be available.

! Turn MIXTRAX off if the visual effects it pro-

duces have adverse effects on driving. Refer

to Operations using the MIXTRAX button on

page 6.

MIXTRAX menu

1 Press M.C. to display the main menu.

2 Turn M.C. to change the menu option

and press to select MIXTRAX.

3 Turn M.C. to select the MIXTRAX func-

tion.

Once selected, the following MIXTRAX functions

can be adjusted. The function is enabled when

MIXTRAX is on.

SHORT PLAYBCK (short playback mode)

You can select the length of the playback time.

1 Press M.C. to display the setting mode.

2 Turn M.C. to select the desired setting.

1.0 MIN (1.0 minute)—1.5 MIN (1.5 minutes)—

2.0 MIN (2.0 minutes)—2.5 MIN (2.5 minutes)

—3.0 MIN (3.0 minutes)—OFF (off)

FLASH AREA (flash area)

Using this unit

10

Section

Using this unit

En

02

<QRD3200-A>10

Black plate (11,1)

You can select areas for flashing colors.

1 Press M.C. to display the setting mode.

2 Turn M.C. to select the desired setting.

KEY/DISPLAY (key and display)—KEY (key)—

OFF (off)

! When OFF is selected, the color set under IL-

LUMI is used as the display color.

FLASH PATTERN (flash pattern)

The flashing color and MIXTRAX special effects

display change with changes in the sound and

bass levels.

1 Press M.C. to display the setting mode.

2 Turn M.C. to select the desired setting.

! SOUND LEVEL 1 to SOUND LEVEL 6 – The

flash pattern changes according to the

sound level. Select a desired mode.

! LOW PASS 1 to LOW PASS 6 – The flash

pattern changes according to the bass

level. Select a desired mode.

! RANDOM 1 – The flash pattern changes

randomly according to the sound level

mode and low pass mode.

! RANDOM 2 – The flash pattern changes

randomly according to the sound level

mode.

! RANDOM 3 – The flash pattern changes

randomly according to the low pass mode.

DISPLAY FX (display effect)

The MIXTRAX special effects display can be turned

on or off.

1 Press M.C. to select the desired setting.

ON (MIXTRAX special effects display)—OFF

(normal display)

CUT IN FX (manual cut-in effect)

You can turn on or off the MIXTRAX sound effects

while manually changing tracks.

1 Press M.C. to select the desired setting.

ON (on)—OFF (off)

Initial menu

1 Press and hold SRC/OFF until the unit

turns off.

2 Press and hold SRC/OFF until the main

menu appears in the display.

3 Turn M.C. to change the menu option

and press to select INITIAL.

4 Turn M.C. to select the initial menu func-

tion.

Once selected, the following initial menu func-

tions can be adjusted.

FM STEP (FM tuning step)

1 Press M.C. to select the FM tuning step.

100 (100 kHz)—50 (50 kHz)

SP-P/O MODE (rear output and preout setting)

The rear speaker leads output and the RCA output

of this unit can be used to connect a full-range

speaker or subwoofer. Select a suitable option for

your connection.

1 Press M.C. to display the setting mode.

2 Turn M.C. to select the desired setting.

! REAR/SUB.W – Select when there is a full-

range speaker connected to the rear speak-

er leads output and there is a subwoofer

connected to the RCA output.

! SUB.W/SUB.W – Select when there is a

subwoofer connected directly to the rear

speaker leads output without any auxiliary

amp and there is a subwoofer connected

to the RCA output.

! REAR/REAR – Select when there is a full-

range speaker connected to the rear speak-

er leads output and the RCA output.

If there is a full-range speaker connected to

the rear speaker leads output and the RCA

output is not used, you may select either

REAR/SUB.W or REAR/REAR.

System menu

1 Press and hold SRC/OFF until the unit

turns off.

2 Press and hold SRC/OFF until the main

menu appears in the display.

3 Turn M.C. to change the menu option

and press to select SYSTEM.

4 Turn M.C. to select the system menu

function.

For details, refer to System menu on page 9.

Using an AUX source

1 Insert the stereo mini plug into the AUX

input jack.

2 Press SRC/OFF to select AUX as the

source.

Note

AUX cannot be selected unless the auxiliary set-

ting is turned on. For more details, refer to AUX

(auxiliary input) on page 9.

Switching the display

Selecting the desired text information

1 Press DISP to cycle between the following:

! Source name

! Source name and clock

If an unwanted display appears

Turn off the unwanted display using the proce-

dures listed below.

1 Press M.C. to display the main menu.

2 Turn M.C. to change the menu option

and press to select SYSTEM.

3 Turn M.C. to display DEMO OFF and press

to select.

4 Turn M.C. to switch to YES.

5 Press M.C. to select.

Mute function

Only for DEH-X3600UI

This function is enabled when there is a device

equipped with a mute function connected to

this unit.

Sound is muted automatically if you make or re-

ceive a phone call with a device equipped with a

mute function.

Note

Phone source displays when you receive a call.

English

Using this unit

11

Section

Using this unit

En

02

<QRD3200-A>11

Black plate (12,1)

Connections

Important

! When installing this unit in a vehicle without

an ACC (accessory) position on the ignition

switch, failure to connect the red cable to the

terminal that detects operation of the ignition

key may result in battery drain.

O

N

S

T

A

R

T

O

F

ACC position No ACC position

! Use of this unit in conditions other than the

following could result in fire or malfunction.

— Vehicles with a 12-volt battery and negative

grounding.

— Speakers with 50 W (output value) and 4 W to

8 W (impedance value).

! To prevent a short-circuit, overheating or mal-

function, be sure to follow the directions

below.

— Disconnect the negative terminal of the bat-

tery before installation.

— Secure the wiring with cable clamps or adhe-

sive tape. Wrap adhesive tape around wiring

that comes into contact with metal parts to

protect the wiring.

— Place all cables away from moving parts,

such as the shift lever and seat rails.

— Place all cables away from hot places, such

as near the heater outlet.

— Do not connect the yellow cable to the battery

by passing it through the hole to the engine

compartment.

— Cover any disconnected cable connectors

with insulating tape.

— Do not shorten any cables.

— Never cut the insulation of the power cable of

this unit in order to share the power with

other devices. The current capacity of the

cable is limited.

— Use a fuse of the rating prescribed.

— Never wire the negative speaker cable directly

to ground.

— Never band together negative cables of multi-

ple speakers.

! When this unit is on, control signals are sent

through the blue/white cable. Connect this

cable to the system remote control of an ex-

ternal power amp or the vehicle’s auto-anten-

na relay control terminal (max. 300 mA

12 V DC). If the vehicle is equipped with a

glass antenna, connect it to the antenna

booster power supply terminal.

! Never connect the blue/white cable to the

power terminal of an external power amp.

Also, never connect it to the power terminal

of the auto antenna. Doing so may result in

battery drain or a malfunction.

! The black cable is ground. Ground cables for

this unit and other equipment (especially,

high-current products such as power amps)

must be wired separately. If they are not, an

accidental detachment may result in a fire or

malfunction.

This unit

5 67

3

4

1

2

1 Power cord input

2 AUX2 input jack (3.5 mm stereo jack) (DEH-

X3600UI only)

A dedicated input jack designed exclusively

for use with devices equipped with a mute

function.

3 Rear output or subwoofer output

4 Front output

5 Antenna input

6 Fuse (10 A)

7 Wired remote input

Hard-wired remote control adapter can be

connected (sold separately).

Power cord

1

3

2

4

5

6

b

8

9

7

a

e

d

c

1 To power cord input

2 Depending on the kind of vehicle, the func-

tion of 3 and 5 may be different. In this

case, be sure to connect 4 to 5 and 6 to

3.

3 Yellow

Back-up (or accessory)

4 Yellow

Connect to the constant 12 V supply termi-

nal.

5 Red

Accessory (or back-up)

6 Red

Connect to terminal controlled by ignition

switch (12 V DC).

7 Connect leads of the same color to each

other.

8 Black (chassis ground)

9 Blue/white

The pin position of the ISO connector will dif-

fer depending on the type of vehicle. Connect

9 and b when Pin 5 is an antenna control

type. In another type of vehicle, never con-

nect 9 and b.

a Blue/white

Connect to system control terminal of the

power amp (max. 300 mA 12 V DC).

b Blue/white

Connect to auto-antenna relay control termi-

nal (max. 300 mA 12 V DC).

c Yellow/black

If you use an equipment with Mute function,

wire this lead to the Audio Mute lead on that

equipment. If not, keep the Audio Mute lead

free of any connections.

d Speaker leads

White: Front left +

White/black: Front left *

Gray: Front right +

Gray/black: Front right *

Green: Rear left + or subwoofer +

Green/black: Rear left * or subwoofer *

Violet: Rear right + or subwoofer +

Violet/black: Rear right * or subwoofer *

e ISO connector

In some vehicles, the ISO connector may be

divided into two. In this case, be sure to con-

nect to both connectors.

Notes

! Change the initial menu of this unit. Refer to

SP-P/O MODE (rear output and preout set-

ting) on page 11.

The subwoofer output of this unit is monau-

ral.

! When using a subwoofer of 70 W (2 W), be

sure to connect the subwoofer to the violet

and violet/black leads of this unit. Do not

connect anything to the green and green/

black leads.

Installation

12

Section

Installation

En

03

<QRD3200-A>12

Black plate (13,1)

Power amp (sold separately)

Perform these connections when using the op-

tional amplifier.

















1

3

2

4

55

3

2

6

77

1 System remote control

Connect to Blue/white cable.

2 Power amp (sold separately)

3 Connect with RCA cables (sold separately)

4 To Front output

5 Front speaker

6 To Rear output or subwoofer output

7 Rear speaker or subwoofer

Installation

Important

! Check all connections and systems before

final installation.

! Do not use unauthorized parts as this may

cause malfunctions.

! Consult your dealer if installation requires

drilling of holes or other modifications to the

vehicle.

! Do not install this unit where:

— it may interfere with operation of the vehicle.

— it may cause injury to a passenger as a result

of a sudden stop.

! The semiconductor laser will be damaged if

it overheats. Install this unit away from hot

places such as near the heater outlet.

! Optimum performance is obtained when the

unit is installed at an angle of less than 60°.

60°

! When installing, to ensure proper heat dis-

persal when using this unit, make sure you

leave ample space behind the rear panel and

wrap any loose cables so they are not block-

ing the vents.

5cmcm

Leave ample

space

5 cm

DIN front/rear mount

This unit can be properly installed using either

front-mount or rear-mount installation.

Use commercially available parts when instal-

ling.

DIN Front-mount

1 Insert the mounting sleeve into the dash-

board.

For installation in shallow spaces, use the sup-

plied mounting sleeve. If there is enough space,

use the mounting sleeve that came with the ve-

hicle.

2 Secure the mounting sleeve by using a

screwdriver to bend the metal tabs (90°) into

place.

1

2

1 Dashboard

2 Mounting sleeve

# Make sure that the unit is installed securely in

place. An unstable installation may cause skipping

or other malfunctions.

DIN Rear-mount

1 Determine the appropriate position

where the holes on the bracket and the side

of the unit match.

2 Tighten two screws on each side.

1

2

3

1 Tapping screw (5 mm × 8 mm)

2 Mounting bracket

3 Dashboard or console

Removing the unit

1 Remove the trim ring.

1 Trim ring

2 Notched tab

! Releasing the front panel allows easier ac-

cess to the trim ring.

! When reattaching the trim ring, point the

side with the notched tab down.

2 Insert the supplied extraction keys into

both sides of the unit until they click into

place.

3 Pull the unit out of the dashboard.

Removing and re-attaching the front

panel

You can remove the front panel to protect your

unit from theft.

For details, refer to Removing the front panel and

Re-attaching the front panel on page 4.

English

Installation

13

Section

Installation

En

03

<QRD3200-A>13

Black plate (14,1)

Troubleshooting

Symptoms are written in bold and causes in reg-

ular, non-indented text. Regular, indented text is

used to indicate actions to be taken.

The display automatically returns to the ordinary

display.

You did not perform any operation within about 30

seconds.

Perform operation again.

The repeat play range changes unexpectedly.

Depending on the repeat play range, the selected

range may change when another folder or track is

being selected or during fast forwarding/reversing.

Select the repeat play range again.

A subfolder is not played back.

Subfolders cannot be played when FLD (folder re-

peat) is selected.

Select another repeat play range.

NO XXXX appears when a display is changed

(NO TITLE, for example).

There is no embedded text information.

Switch the display or play another track/file.

The unit is malfunctioning.

There is interference.

You are using a device, such as a cellular phone,

that may cause audible interference.

Move electrical devices that may be causing the

interference away from the unit.

Error messages

When you contact your dealer or your nearest

Pioneer Service Center, be sure to note the error

message.

Symptoms are written in bold and causes in reg-

ular, non-indented text. Regular, indented text is

used to indicate actions to be taken.

Common

AMP ERROR

This unit fails to operate or the speaker connection is

incorrect; the protective circuit is activated.

Check the speaker connection. If the message

fails to disappear even after the engine is

switched off/on, contact your dealer or an

authorized Pioneer Service Station for

assistance.

CD player

ERROR-07, 11, 12, 17, 30

The disc is dirty.

Clean the disc.

The disc is scratched.

Replace the disc.

ERROR-07, 10, 11, 12, 15, 17, 30, A0

There is an electrical or mechanical error.

Turn the ignition switch OFF and back ON, or

switch to a different source, then back to the CD

player.

ERROR-15

The inserted disc is blank.

Replace the disc.

ERROR-23

Unsupported CD format.

Replace the disc.

FORMAT READ

Sometimes there is a delay between the start of play-

back and when you start to hear any sound.

Wait until the message disappears and you hear

sound.

NO AUDIO

The inserted disc does not contain any playable files.

Replace the disc.

SKIPPED

The inserted disc contains DRM protected files.

The protected files are skipped.

PROTECT

All the files on the inserted disc are embedded with

DRM.

Replace the disc.

USB storage device/iPod

FORMAT READ

Sometimes there is a delay between the start of play-

back and when you start to hear any sound.

Wait until the message disappears and you hear

sound.

NO AUDIO

There are no songs.

Transfer the audio files to the USB storage device

and connect.

The connected USB storage device has security en-

abled.

Follow the USB storage device instructions to

disable the security.

SKIPPED

The connected USB storage device contains DRM

protected files.

The protected files are skipped.

PROTECT

All the files on the connected USB storage device

are embedded with DRM.

Replace the USB storage device.

N/A USB

The connected USB device is not supported by this

unit.

! Connect a USB Mass Storage Class compliant

device.

! Disconnect your device and replace it with a

compatible USB storage device.

CHECK USB

The USB connector or USB cable has short-

circuited.

Check that the USB connector or USB cable is

not caught in something or damaged.

CHECK USB

The connected USB storage device consumes more

than maximum allowable current.

Disconnect the USB storage device and do not

use it. Turn the ignition switch to OFF, then to

ACC or ON and then connect only compliant

USB storage devices.

CHECK USB

The iPod operates correctly but does not charge.

Make sure the connection cable for the iPod has

not shorted out (e.g., not caught in metal

objects). After checking, turn the ignition switch

OFF and back ON, or disconnect the iPod and

reconnect.

ERROR-19

Communication failed.

Perform one of the following operations.

–Turn the ignition switch OFF and back ON.

–Disconnect the USB storage device.

–Change to a different source.

Then, return to the USB source.

Additional information

14

Appendix

Additional information

En

<QRD3200-A>14

Black plate (15,1)

iPod failure.

Disconnect the cable from the iPod. Once the

iPod’s main menu is displayed, reconnect the

iPod and reset it.

ERROR-23

USB storage device was not formatted with FAT12,

FAT16 or FAT32.

USB storage device should be formatted with

FAT12, FAT16 or FAT32.

ERROR-16

The iPod firmware version is old.

Update the iPod version.

iPod failure.

Disconnect the cable from the iPod. Once the

iPod’s main menu is displayed, reconnect the

iPod and reset it.

STOP

There are no songs in the current list.

Select a list that contains songs.

NOT FOUND

No related songs.

Transfer songs to the iPod.

Apps

START UP APP

The application has not started running yet.

Follow the instructions that appear on the

screen.

Handling guidelines

Discs and player

Use only discs that feature either of the following

two logos.

Use 12-cm discs.

Use only conventional, fully circular discs.

The following types of discs cannot be used with

this unit:

! DualDiscs

! 8-cm discs: Attempts to use such discs with

an adaptor may cause the unit to malfunction.

! Oddly shaped discs

! Discs other than CDs

! Damaged discs, including discs that are

cracked, chipped or warped

! CD-R/RW discs that have not been finalized

Do not touch the recorded surface of the discs.

Store discs in their cases when not in use.

Do not attach labels, write on or apply chemicals

to the surface of the discs.

To clean a CD, wipe the disc with a soft cloth out-

ward from the center.

Condensation may temporarily impair the player’s

performance. Let it rest for about one hour to ad-

just to a warmer temperature. Also, wipe any

damp discs off with a soft cloth.

Playback of discs may not be possible because of

disc characteristics, disc format, recorded applica-

tion, playback environment, storage conditions,

and so on.

Road shocks may interrupt disc playback.

When using discs that can be printed on label sur-

faces, check the instructions and the warnings of

the discs. Depending on the discs, inserting and

ejecting may not be possible. Using such discs

may result in damage to this equipment.

Do not attach commercially available labels or

other materials to the discs.

! The discs may warp making the disc unplay-

able.

! The labels may come off during playback and

prevent ejection of the discs, which may result

in damage to the equipment.

USB storage device

Connections via USB hub are not supported.

Do not connect anything other than a USB stor-

age device.

Firmly secure the USB storage device when driv-

ing. Do not let the USB storage device fall onto the

floor, where it may become jammed under the

brake or accelerator pedal.

Depending on the USB storage device, the follow-

ing problems may occur.

! Operations may vary.

! The storage device may not be recognized.

! Files may not be played back properly.

! The device may cause audible interference

when you are listening to the radio.

iPod

Do not leave the iPod in places with high tempera-

tures.

Firmly secure the iPod when driving. Do not let the

iPod fall onto the floor, where it may become

jammed under the brake or accelerator pedal.

About iPod settings

! When an iPod is connected, this unit changes

the EQ (equalizer) setting of the iPod to off in

order to optimize the acoustics. When you dis-

connect the iPod, the EQ returns to the original

setting.

! You cannot set Repeat to off on the iPod when

using this unit. Repeat is automatically

changed to All when the iPod is connected to

this unit.

Incompatible text saved on the iPod will not be dis-

played by the unit.

Compressed audio

compatibility (disc, USB)

WMA

File extension: .wma

Bit rate: 48 kbps to 320 kbps (CBR), 48 kbps to

384 kbps (VBR)

Sampling frequency: 32 kHz, 44.1 kHz, 48 kHz

Windows Mediaä Audio Professional, Lossless,

Voice/DRM Stream/Stream with video: Not com-

patible

MP3

File extension: .mp3

Bit rate: 8 kbps to 320 kbps (CBR), VBR

English

Additional information

15

Appendix

Additional information

En

<QRD3200-A>15

Black plate (16,1)

Sampling frequency: 8 kHz to 48 kHz (32 kHz,

44.1 kHz, 48 kHz for emphasis)

Compatible ID3 tag version: 1.0, 1.1, 2.2, 2.3, 2.4

(ID3 tag Version 2.x is given priority over Version

1.x.)

M3u playlist: Not compatible

MP3i (MP3 interactive), mp3 PRO: Not compatible

WAV

File extension: .wav

Quantization bits: 8 and 16 (LPCM), 4 (MS

ADPCM)

Sampling frequency: 16 kHz to 48 kHz (LPCM),

22.05 kHz and 44.1 kHz (MS ADPCM)

! You cannot use this function with USB MTP.

Supplemental information

Only the first 32 characters can be displayed as a

file name (including the file extension) or a folder

name.

Russian text to be displayed on this unit should be

encoded in one of the following character sets:

! Unicode (UTF-8, UTF-16)

! A character set other than Unicode that is

used in a Windows environment and is set to

Russian in the multi-language setting

This unit may not work properly depending on the

application used to encode WMA files.

There may be a slight delay at the start of playback

of audio files embedded with image data or audio

files stored on a USB storage device that has nu-

merous folder hierarchies.

Disc

Playable folder hierarchy: up to eight tiers (A prac-

tical hierarchy is less than two tiers.)

Playable folders: up to 99

Playable files: up to 999

File system: ISO 9660 Level 1 and 2, Romeo, Joliet

Multi-session playback: Compatible

Packet write data transfer: Not compatible

Regardless of the length of blank sections be-

tween the songs from the original recording, com-

pressed audio discs play with a short pause

between songs.

USB storage device

Playable folder hierarchy: up to eight tiers (A prac-

tical hierarchy is less than two tiers.)

Playable folders: up to 500

Playable files: up to 15 000

Playback of copyright-protected files: Not compati-

ble

Partitioned USB storage device: Only the first par-

tition can be played.

There may be a slight delay when starting play-

back of audio files on a USB storage device with

numerous folder hierarchies.

CAUTION

! Pioneer cannot guarantee compatibility with

all USB mass storage devices and assumes

no responsibility for any loss of data on

media players, smart phones, or other devi-

ces while using this product.

! Do not leave discs or a USB storage device

in any place that is subject to high tempera-

tures.

iPod compatibility

This unit supports only the following iPod mod-

els. Supported iPod software versions are shown

below. Older versions may not be supported.

Made for

! iPod touch (5th generation)

! iPod touch (4th generation)

! iPod touch (3rd generation)

! iPod touch (2nd generation)

! iPod touch (1st generation)

! iPod classic

! iPod with video

! iPod nano (7th generation)

! iPod nano (6th generation)

! iPod nano (5th generation)

! iPod nano (4th generation)

! iPod nano (3rd generation)

! iPod nano (2nd generation)

! iPod nano (1st generation)

! iPhone 5

! iPhone 4S

! iPhone 4

! iPhone 3GS

! iPhone 3G

! iPhone

Depending on the generation or version of the

iPod, some functions may not be available.

Operations may vary depending on the software

version of iPod.

Users of iPod with the Lightning Connector should

use the Lightning to USB Cable (supplied with

iPod).

Users of iPod with the Dock Connector should use

CD-IU51. For details, consult your dealer.

About the file/format compatibility, refer to the

iPod manuals.

Audiobook, Podcast: Compatible

CAUTION

Pioneer accepts no responsibility for data lost

on the iPod, even if that data is lost while this

unit is used.

Sequence of audio files

The user cannot assign folder numbers and

specify playback sequences with this unit.

Example of a hierarchy













Level 1 Level 2 Level 3 Level 4

01

02

03

04

05

: Folder

: Compressed

audio file

01 to 05: Folder

number

1 to 6: Playback

sequence

Disc

Folder selection sequence or other operation

may differ depending on the encoding or writing

software.

USB storage device

Playback sequence is the same as recorded se-

quence in the USB storage device.

To specify the playback sequence, the following

method is recommended.

1 Create a file name that includes numbers

that specify the playback sequence (e.g.,

001xxx.mp3 and 099yyy.mp3).

2 Put those files into a folder.

Additional information

16

Appendix

Additional information

En

<QRD3200-A>16

Black plate (17,1)

3 Save the folder containing files on the USB

storage device.

However, depending on the system environment,

you may not be able to specify the playback se-

quence.

For USB portable audio players, the sequence is

different and depends on the player.

Russian character chart

D: C D: C D: C D: C D: C

: А : Б : В : Г : Д

: Е, Ё : Ж : З : И, Й : К

: Л : М : Н : О : П

: Р : С : Т : У : Ф

: Х : Ц : Ч

: Ш,

Щ

: Ъ

: Ы : Ь : Э : Ю : Я

D: Display C: Character

Copyright and trademark

iTunes

Apple and iTunes are trademarks of Apple Inc.,

registered in the U.S. and other countries.

MP3

Supply of this product only conveys a license for

private, non-commercial use and does not con-

vey a license nor imply any right to use this prod-

uct in any commercial (i.e. revenue-generating)

real time broadcasting (terrestrial, satellite,

cable and/or any other media), broadcasting/

streaming via internet, intranets and/or other

networks or in other electronic content distribu-

tion systems, such as pay-audio or audio-on-de-

mand applications. An independent license for

such use is required. For details, please visit

http://www.mp3licensing.com.

WMA

Windows Media is either a registered trademark

or trademark of Microsoft Corporation in the

United States and/or other countries.

This product includes technology owned by

Microsoft Corporation and cannot be used or

distributed without a license from Microsoft

Licensing, Inc.

iPod & iPhone

iPhone, iPod, iPod classic, iPod nano, and iPod

touch are trademarks of Apple Inc., registered in

the U.S. and other countries.

Lightning is a trademark of Apple Inc.

“Made for iPod” and “Made for iPhone” mean

that an electronic accessory has been designed

to connect specifically to iPod or iPhone, respec-

tively, and has been certified by the developer to

meet Apple performance standards. Apple is

not responsible for the operation of this device

or its compliance with safety and regulatory

standards. Please note that the use of this ac-

cessory with iPod or iPhone may affect wireless

performance.

Androidä

Android is a trademark of Google Inc.

MIXTRAX

MIXTRAX is a trademark of the PIONEER

CORPORATION.

English

Additional information

17

Appendix

Additional information

En

<QRD3200-A>17

Black plate (18,1)

Specifications

General

Power source ................... 14.4 V DC (10.8 V to 15.1 V al-

lowable)

Grounding system ............ Negative type

Maximum current consumption

................................... 10.0 A

Dimensions (W × H × D):

DIN

Chassis ............................ 178mm × 50mm × 165mm

Nose ................................ 188 mm × 58mm × 15mm

D

Chassis ............................ 178mm × 50mm × 165mm

Nose ................................ 170 mm × 46mm × 15mm

(DEH-X3600UI)

Nose ................................ 170 mm × 46mm × 16mm

(DEH-2600UI)

Weight ............................. 1 kg

Audio

Maximum power output ... 50 W × 4

70 W × 1/2 W (for subwoofer)

Continuous power output

................................... 22W × 4 (50Hz to 15000 Hz,

5 % THD, 4 W load, both chan-

nels driven)

Load impedance .............. 4 W (4 W to 8 W allowable)

Preout maximum output level

................................... 2.0V

Loudness contour ............ +10dB (100 Hz), +6.5 dB

(10 kHz) (volume: –30 dB)

Equalizer (5-Band Graphic Equalizer):

Frequency ........................ 80Hz/250 Hz/800 Hz/2.5 kHz/

8 kHz

Equalization range ........... ±12 dB (2 dB step)

Subwoofer (mono):

Frequency ........................ 50Hz/63 Hz/80 Hz/100 Hz/

125 Hz/160 Hz/200 Hz

Slope ............................... –12 dB/oct, –24 dB/oct

Gain ................................ +6dB to –24 dB

Phase .............................. Normal/Reverse

CD player

System ............................ Compact disc audio system

Usable discs .................... Compact disc

Signal-to-noise ra tio ......... 94dB (1 kHz) (IEC-A network)

Number of channels ........ 2 (stereo)

MP3 decoding format ...... MPEG-1 & 2 Audio Layer 3

WMA decoding format ..... Ver. 7, 7.1, 8, 9, 10, 11, 12 (2ch

audio)

(Windows Media Player)

WAV signal format ........... Linear PCM & MS ADPCM

(Non-compressed)

USB

USB standard specification

................................... USB 2.0 full speed

Maximum current supply

................................... 1 A

USB Class ....................... MSC (Mass Storage Class)

File system ....................... FAT12, FAT16, FAT32

MP3 decoding format ...... MPEG-1 & 2 Audio Layer 3

WMA decoding format ..... Ver. 7, 7.1, 8, 9, 10, 11, 12 (2ch

audio)

(Windows Media Player)

WAV signal format ........... Linear PCM & MS ADPCM

(Non-compressed)

FM tuner

Frequency range .............. 87.5 MHz to 108.0 MHz

Usable sensitivity ............. 9dBf (0.8 µV/75 W, mono, S/N:

30 dB)

Signal-to-noise ra tio ......... 72dB (IEC-A network)

MW tuner

Frequency range .............. 531 kHz to 1 602 kHz

Usable sensitivity ............. 25µV (S/N: 20 dB)

Signal-to-noise ra tio ......... 62dB (IEC-A network)

LW tuner

Frequency range .............. 153 kHz to 281kHz

Usable sensitivity ............. 28µV (S/N: 20 dB)

Signal-to-noise ra tio ......... 62dB (IEC-A network)

Note

Specifications and the design are subject to

modifications without notice.

Additional information

18

Appendix

En

<QRD3200-A>18

Black plate (19,1)

English

19En

<QRD3200-A>19

Black plate (20,1)

Nous vous remercions d’avoir acheté cet ap-

pareil PIONEER

Pour garantir une utilisation correcte, lisez bien

ce mode d’emploi avant d’utiliser cet appareil. Il

est particulièrement important que vous lisiez et

respectiez les indications ATTENTION et PRÉ-

CAUTION de ce mode d’emploi. Conservez-le

dans un endroit sûr et facilement accessible pour

toute consultation ultérieure.

Si vous souhaitez vous débarrasser de cet ap-

pareil, ne le mettez pas à la poubelle avec vos

ordures ménagères. Il existe un système de

collecte séparé pour les appareils électroni-

ques usagés, qui doivent être récupérés, trai-

tés et recyclés conformément à la législation.

Dans les états membres de l’UE, en Suisse et en

Norvège, les foyers domestiques peuvent rap-

porter leurs produits électroniques usagés gra-

tuitement à des points de collecte spécifiés ou à

un revendeur (sous réserve d’achat d’un produit

similaire).

Dans les pays qui ne sont pas mentionnés ci-

dessus, veuillez contacter les autorités locales

pour vous informer de la méthode correcte de

mise au rebut.

En agissant ainsi vous assurerez que le produit

que vous mettez au rebut est soumis au proces-

sus de traitement, de récupération et de recy-

clage nécessaire et éviterez ainsi les effets

négatifs potentiels sur l’environnement et la

santé publique.

Quelques mots sur cet appareil

Les fréquences du syntoniseur de cet appareil

sont attribuées pour une utilisation en Europe

de l’Ouest, Asie, Moyen-Orient, Afrique et Océ-

anie. Son utilisation dans d’autres régions peut

se traduire par une réception de mauvaise qua-

lité. La fonction RDS (radio data system) n’est

opérationnelle que dans les régions où des si-

gnaux RDS sont diffusés pour les stations FM.

ATTENTION

! N’essayez pas d’installer cet appareil ou

d’en faire l’entretien vous-même. L’instal-

lation ou l’entretien de cet appareil par

des personnes sans formation et sans ex-

périence en équipement électronique et

en accessoires automobiles peut être

dangereux et vous exposer à des risques

d’électrocution ou à d’autres dangers.

! N’essayez pas de démonter ou de modifier

cet appareil. Veillez à quitter la route et garer

votre véhicule en lieu sûr avant d’essayer d’u-

tiliser les commandes de l’appareil.

PRÉCAUTION

! Ne laissez pas cet appareil entrer en contact

avec des liquides. Cela pourrait provoquer

une électrocution. Tout contact avec des li-

quides pourrait également provoquer des

dommages, de la fumée et une surchauffe

de l’appareil.

! Le Pioneer CarStereo-Pass est utilisable seu-

lement en Allemagne.

! Maintenez le niveau d’écoute à une valeur

telle que vous puissiez entendre les sons pro-

venant de l’extérieur.

! Évitez tout contact avec l’humidité.

PRÉCAUTION

Cet appareil est un produit laser de Classe 1,

classé selon l’article IEC 60825-1:2007 relatif à

la Sécurité des produits laser.

APPAREIL À LASER DE CLASSE 1

Si vous rencontrez des

problèmes

En cas d’anomalie, veuillez contacter votre re-

vendeur ou le centre d’entretien agréé par

PIONEER le plus proche.

Avant de commencer

20

Section

Avant de commencer

Fr

01

<QRD3200-A>20

La page est en cours de chargement...

Pioneer DEH-2600UI Manuel utilisateur

Pioneer DEH-2600UI Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents