Sub-Zero OG30 Guide d'installation

OUTDOOR GAS GRILL

INSTALLATION GUIDE

SPECIFICATIONS, INSTALLATION, AND MORE

OUTDOOR GAS GRILL

Contents

3 Outdoor Gas Grill

4 Safety Precautions

5 Specications

9 Installation

18 Troubleshooting

Features and specications are subject to change at any

time without notice. Visit wolfappliance.com/specs for the

most up-to-date information.

2

|

Wolf Customer Care 800.222.7820

Important Note

To ensure this product is installed and operated as safely

and efciently as possible, take note of the following types

of highlighted information throughout this guide:

IMPORTANT NOTE highlights information that is especially

important.

CAUTION indicates a situation where minor injury or product

damage may occur if instructions are not followed.

WARNING states a hazard that may cause serious injury or

death if precautions are not followed.

IMPORTANT NOTE: Throughout this guide, dimensions in

parentheses are millimeters unless otherwise specied.

IMPORTANT NOTE: Save these instructions for the local

electrical inspector.

wolfappliance.com

|

3

OUTDOOR GAS GRILL

Product Information

Important product information, including the model and

serial number, are listed on the product rating plate. For

outdoor grills, the rating plate is located above the drip tray,

behind the logo. The drip tray must be removed to view the

rating plate. For outdoor modules, the rating plate is located

on the bottom of the control panel, on the right side. Refer

to the illustrations below.

If service is necessary, contact Wolf Factory Certied

Service with the model and serial number. For the name of

the nearest Wolf Factory Certied Service or for questions

regarding the installation, visit the contact and support

section of our website, wolfappliance.com, or call Wolf

Customer Care at 800-222-7820.

Outdoor gas grill

Outdoor module

RATING PLATE

4

|

Wolf Customer Care 800.222.7820

IMPORTANT INSTRUCTIONS

• Wolf outdoor gas grills and modules are for

outdoor use only. Do not install or operate in an

enclosed area.

• Installation must be performed by a qualied

installer, service agency or the gas supplier.

• Warranty service must be performed by Wolf

Factory Certied Service.

• Do not store or use gasoline or other ammable

liquids or vapors in the vicinity of this or any other

appliance. An LP gas cylinder not connected for

use shall not be stored in the vicinity of this or any

other appliance.

• In Massachusetts: All gas products must be

installed using a “Massachusetts” licensed

plumber or gastter. A “T” handle type manual gas

valve must be installed in the gas supply line to this

appliance. This applies to permanently installed

natural gas and propane installations. This does

not apply to propane portable installations using a

20-lb tank.

• A built-in appliance for use with a remote self-con-

tained LP gas supply system must use rigid pipe,

semi-rigid tubing, or a connector complying with

the Standard for Connectors for Gas Appliances,

ANSI Z21.24/CSA 6.10, or the Standard for Con-

nectors for Outdoor Gas Appliances and Manufac-

tured Homes, ANSI Z21.75/CSA 6.27, to connect

the appliance to the remote self-contained gas

supply system. When using semi-rigid tubing, alu-

minum, or aluminum alloy tubing is not permitted.

BEFORE LIGHTING:

• Read instructions before lighting.

• Open the hood or remove the cover before

lighting.

• If ignition does not occur in 5 seconds, turn

the burner control(s) off, wait 5 minutes, and

repeat the lighting procedure.

WHAT TO DO IF YOU SMELL GAS:

• Shut off gas to the appliance.

• Extinguish any open ames.

• Open the hood or remove the cover.

• If the odor continues, keep away from the

appliance and immediately call your gas

supplier or re department.

SAFETY PRECAUTIONS

wolfappliance.com

|

5

Installation Requirements

For portable applications, Wolf grill carts are designed

specically to t grill models OG30, OG36 and OG42 and

the side burner. Model OG54 is designed for built-in appli-

cations only.

For built-in applications, Wolf outdoor grills and the burner

module are designed for easy placement into a built-in

enclosure. For outdoor grills, installation in a combustible

enclosure requires an insulating liner. For the burner module,

an insulating liner is not required. The enclosure should be

built according to specications for your specic installa-

tion on the following pages. If the burner module is installed

next to an outdoor grill, a minimum of 12"

(305) is required

between the units on the rotisserie motor side and 2"

(51) on

the opposite side. A rotisserie side conversion kit is avail-

able from an authorized Wolf dealer.

Grill carts, insulating liners, and stainless steel doors and

drawers are avail able through an authorized Wolf dealer. For

local dealer information, visit the nd a showroom section of

our website, wolfappliance.com.

SPECIFICATIONS

Electrical Requirements

Installation must comply with all applicable electrical codes.

The electrical outlet must be located within reach of the

power cord. A separate circuit, servicing only this appliance

is required.

IMPORTANT NOTE: A ground fault circuit interrupter (GFCI)

is required to reduce the risk of electrical shock.

ELECTRICAL REQUIREMENTS

Electrical Supply grounded, 120 VAC, 60 Hz

Service 15 amp dedicated circuit

Receptacle 3-prong grounding-type, GFCI

Power Cord 6'

(1.8 m), 9' (2.7 m) rotisserie

6

|

Wolf Customer Care 800.222.7820

SPECIFICATIONS

Gas Supply

Installation must comply with local codes or, in the absence

of local codes, with the National Fuel Gas Code.

Locate the gas supply within the shaded area shown in the

illustrations on pages 7–8.

The outdoor grill is equipped for use with natural or liquid

propane (LP) gas. It is design certied by the Canadian

Standards Association (CSA) for natural or LP gases. The

product rating plate has information on the type of gas that

should be used. For rating plate location, refer to the illustra-

tion below. If this information does not agree with the type

of gas available, check with the local gas supplier.

GAS REQUIREMENTS

NATURAL GAS WC

Supply Pressure 5" (12.5 mb)

Min Line Pressure 7" (17.5 mb)

Max Regulator Pressure 14" (34.9 mb), .5 psi (3.5 kPa)

LP GAS WC

Supply Pressure 10" (25 mb)

Min Line Pressure 11" (27.4 mb)

Max Regulator Pressure 14" (34.9 mb), .5 psi (3.5 kPa)

The outdoor grill must be connected to a regulated gas

supply. The supply line must be equipped with an approved

external gas shut-off valve located near the grill in an acces-

sible location. Do not block access to the shut-off valve.

Refer to the illustration below.

A gas supply of

3

/4" (19) ID line must be provided to the

outdoor grill or module. If local codes permit, a certied,

3'

(.9 m) long,

1

/2" (13) or

3

/4" (19) ID exible metal appliance

connector is recommended to connect the units

1

/2" NPT

female inlet to the gas supply line. Pipe joint compounds,

suitable for use with natural or LP gas should be used.

The appliance and its shut-off valve must be disconnected

from the gas supply piping system during any pressure

testing of the system at test pressures in excess of .5 psi

(3.5 kPa)

. The appliance must be isolated from the gas

supply piping system by closing its individual manual shut-

off valve during any pressure testing of the system at test

pressures equal to or less than .5 psi

(3.5 kPa).

Outdoor gas grill

Outdoor module

RATING PLATE

SHUT-OFF VALVE

OPEN POSITION

GAS SUPPLYTO APPLIANCE

Gas shut-off valve

wolfappliance.com

|

7

SPECIFICATIONS

11

3

/4"

(298)

OPENING

HEIGHT

DOORS / DRAWERS

OPENING WIDTH

24

1

/4" (616)

OPENING

DEPTH

OPENING

HEIGHT

6"

(152)

1" (25) min

GRILL

OPENING

13

/

16

"

(21)

COUNTERTOP

OVERHANG

GRILL

OVERLAP

FRONT VIEW

TOP VIEW

W

OPENING WIDTH

NO

TE: Shaded area above countertop indicates minimum clearance to

combus

tible surfaces, combustible materials cannot be located within this area.

2

1

/2" (64)

13"

(330)

3

1

/2"

(89)

G

4"

(102)

6"

(152)

G

12

5

/8"

(321)

OPENING

HEIGHT

DOORS / DRAWERS

OPENING WIDTH

26" (660)

OPENING

DEPTH

OPENING

HEIGHT

12"

(305)

1" (25) min

10

3

/

4

"

(273)

5"

(127)

C

L

C

L

2

3

/4" (70)

KNOCKOUT

LINER

OPENING

13

/

16

"

(21)

COUNTERTOP

OVERHANG

LINER

OVERLAP

FRONT VIEW

TOP VIEW

W

OPENING WIDTH

NOTE: Shaded area above countertop indicates minimum clearance to

combustible surfaces, combustible materials cannot be located within this area.

12"

(305)

G

NON-COMBUSTIBLE ENCLOSURE

WIDTH (W)

OG30 28

1

/2" (724)

OG36 34

1

/2" (876)

OG42 40

1

/2" (1029)

OG54 52

1

/2" (1334)

Outdoor Grills

NON-COMBUSTIBLE INSTALLATION COMBUSTIBLE INSTALLATION

COMBUSTIBLE ENCLOSURE

WIDTH (W)

OG30 33

1

/2" (851)

OG36 39

1

/2" (1003)

OG42 45

1

/2" (1156)

OG54 57

1

/2" (1461)

8

|

Wolf Customer Care 800.222.7820

SPECIFICATIONS

10" (254)

OPENING

HEIGHT

24

1

/4" (616)

OPENING

DEPTH

6"

(152)

MODULE

OPENING

9

/16"

(14)

COUNTERTOP

OVERHANG

MODULE

OVERLAP

FRONT VIEW

TOP VIEW

12"

(305)

OPENING

NOTE: Shaded area above countertop indicates minimum clearance to

combustible surfaces, combustible materials cannot be located within this area.

An insulating liner is not required.

G

8"

(203)

7"

(178)

G

3"

(76)

12" (305)

Burner Module

INSTALLATION

Outdoor Grills

ACCESSORY DOORS AND DRAWERS

OPENING

DOORS W H

18" Single 16

1

/4" (413) 19" (483)

30" Double 28

1

/4" (718) 19" (483)

36" Double 34

1

/4" (870) 19" (483)

42" Double 40

1

/4" (1022) 19" (483)

54" Double 52

1

/4" (1327) 19" (483)

DRAWERS W H

Single Drawer 27

1

/4" (692) 9

3

/4" (248)

2- or 3-Drawer Unit 12

1

/8" (308) 19" (483)

Drawer | Door Unit 29

1

/4" (743) 19" (483)

wolfappliance.com

|

9

INSTALLATION

Gas Supply Line

NATURAL GAS CONNECTION

Install the natural gas pressure regulator supplied with the

outdoor product with the arrow on the regulator pointing

towards the unit. Refer to the illustrations below for a typical

natural gas installation.

REGULATOR

REAR GAS

CONNECTION

BOTTOM GAS

CONNECTION

SHUT-OFF

VALVE

FROM GAS

SUPPLY

REGULATOR

TO GRILL

ADAPTER

CLOSE

NIPPLE

VENT

Natural gas connection

Natural gas regulator

LP GAS CONNECTION

For a whole house LP gas connection, the LP gas pres-

sure regulator is not provided. It can be purchased from an

authorized Wolf dealer. For local dealer information, visit the

nd a showroom section of our website, wolfappliance.com.

For connection to LP gas cylinder, use only the LP gas pres-

sure regulator and hose supplied with the outdoor product.

Use only a 20-lb LP gas cylinder with an approved overlling

preventive device (OPD) and shut-off valve terminating in

the cylinder valve outlet.

1 Connect the

3

/8" are end of the hose to the unit cou-

pling. Do not apply pipe sealant to the are connection.

2 Install the LP gas cylinder, pull out the shelf, and place

the cylinder on it. Refer to the illustration below.

3 Ensure the gas valve on top of the cylinder is closed.

4 Connect the LP gas regulator to the cylinder and hand-

tighten only. Open the cylinder valve. Check for gas

leaks. Refer to the illustration below.

5 Tighten the LP tank retention screw to secure the

cylinder to the shelf.

WARNING

Perform a gas leak test each time the LP gas cylinder is

changed. Do not place more than one LP gas cylinder

in an enclosure at a time.

LP TANK

RETENTION SCREW

GRILL

COUPLING

NUT

REGULATOR

VENT

TO GRILL

LP tank shelf

LP gas cylinder connection

10

|

Wolf Customer Care 800.222.7820

INSTALLATION

Gas Supply Line

LP GAS SAFETY REQUIREMENT

This gas appliance and its individual shut-off valve must

be disconnected from the gas supply piping system during

any pressure testing of that system at test pressures greater

than .5 psi (3.5 kPa).

This gas appliance must be isolated from the gas supply

piping system by closing its individual manual shut-off valve

during pressure testing of the gas supply piping system at

test pressures equal to or less than .5 psi (3.5 kPa).

GAS LEAK TESTING

Perform a gas leak test at least once a year, each time the

LP gas cylinder is connected to the regulator, and any time

part of the gas line is disconnected or replaced. This applies

to natural gas as well as LP gas.

1 Prepare a leak testing solution of half liquid soap and

half water in a spray bottle.

2 Verify all control knobs are in the OFF position.

3 Turn the cylinder valve knob counterclockwise one turn

to open.

4 Spray the leak testing solution on pipe joints, ttings,

and hose. Bubbles in the solution indicate a gas leak.

5 Tighten any loose joint or replace any faulty part with a

Wolf replacement part to stop the leak. Do not attempt to

repair the cylinder valve. If damaged, the cylinder must

be replaced.

6 If the leak persists, shut off the gas supply at the cylinder

valve and remove the LP gas cylinder. Call Wolf Factory

Certied Service. Do not use the outdoor product until

the leak has been xed.

7 Push in and turn any control knob to the ON position to

release pressure, then turn the control knob back to OFF.

WARNING

To prevent re or explosion hazard, do not smoke or

permit sources of ignition in the area while performing

a gas leak test. Perform the gas leak test outdoors in a

well ventilated area. Never use an open ame to check

for gas leaks.

wolfappliance.com

|

11

Installation

PREPARATION

Remove and recycle packing materials. Remove labels and

the protective plastic lm from the grill.

Place the briquette trays in the grill above the burners with

the ash tubes positioned at the front. Refer to the illus-

tration below. Place the burner grates directly above the

briquette trays with the square openings in the grates at the

front.

POWER TRANSFORMER

For a built-in installation, secure the transformer box in a dry

location, away from the grill rebox and excessive heat area,

but within 2'

(.6 m) of the right rear opening. Do not install

the transformer box inside the insulating liner.

For a cart installation, mount the transformer box by the two

screws located at the bottom right rear corner of the grill

cart, behind the pull-out shelf. Use the same transformer for

the side burner if installed.

FLASH TUBE

Flash tube position

CART INSTALLATION

1 Two mounting screws are provided at the bottom right

rear corner of the cart for the power transformer. Install

the transformer box.

2 Remove the front mounting screws from the cart. Place

the grill onto the cart, allowing enough space at the back

to make the connection to the transformer.

3 Make the connections from the wiring harness located at

the right rear of the grill to the transformer, then slide the

grill back until it is fully engaged with the cart.

4 Secure the grill to the cart with the four screws provided.

Mounting holes in the upper back corners of the grill will

align with the holes in the cart. Secure with two screws.

Remove the drip tray. Install two screws through the side

mounting holes below the grill front panel and into the

cart.

INSTALLATION

12

|

Wolf Customer Care 800.222.7820

Side Burner Installation

The Wolf side burner can be installed on the right side of

any Wolf grill cart.

PREPARE GRILL CART

1 If installed, the right side shelf must be removed. To

remove, lift the shelf up so the lower front screw is

exposed, then remove the screw. Refer to the illustration

below.

2 Fold the side shelf down and remove the upper front

screw, then remove the side shelf and front bracket.

Refer to the illustration below.

LOWER SCREW

UPPER

SCREW

SIDE SHELF

FRONT

BRACKET

Side shelf lower screw

Side shelf upper screw

3 Remove the rear screws and bracket, then remove the

cart plug from the access hole by pushing out from

inside the cart. Refer to the illustration below.

4 For easier access, the upper rear panel and right side

door of the cart can be removed. Remove the rear panel

by removing the four screws.

5 To remove the right side door, depress the rear lever on

each hinge, then remove the door. Refer to the illustra-

tion below.

6 For easier access, the drip tray of the grill can be

removed. To remove, slide forward and lift out.

7 Insert the provided plastic bushing through the access

hole from inside the grill cart where the cart plug was

removed previously.

REAR

BRACKET

CART PLUG

REAR LEVER

DRIP TRAY

Remove rear bracket and plug

Remove cart door

INSTALLATION

wolfappliance.com

|

13

Side Burner Installation

INSTALL SIDE BURNER SHROUD

1 The side burner is placed inside the shroud for shipping.

Lift out to remove.

2 Hang the shroud by hand-starting the four provided

10-32 machine screws through the upper slots of the

shroud into the upper holes of the cart. Do not fully

tighten the screws until the shroud is properly aligned.

Refer to the illustration below.

3 Place the provided alignment tool with the lip placed in

the gap between the grill and the shroud as shown in the

illustration below.

4 To align the front of the shroud, push the alignment tool

back until the center block of the tool is ush against the

front vertical ange of the shroud.

5 Align the front of the shroud (up and down) with the

alignment tool until the top of the tool is ush with the

top surface of the grill bullnose. Align the shroud (front to

back) with the tool until the front of the tool is ush with

the front of the bullnose. Tighten the upper screw. Refer

to the illustration below.

SCREWS

ALIGNMENT

TOOL

SURFACES

FLUSH

UPPER

SCREW

Hang shroud

Align front of shroud

6 To align the back of the shroud, place the alignment tool

at the rear of the shroud. Align the rear of the shroud (up

and down) with the tool until the top of the tool is ush

with the top surface of the grill. Tighten the upper screw.

Refer to the illustration below. With the alignment tool,

verify the front of the shroud did not move, realign if

necessary.

7 Remove the alignment tool and tighten the two

remaining screws to the slots just below the upper

screws.

8 Install the two provided

5

/16 x

3

/8 hex drive shoulder

screws into the lower holes of the shroud and through

the cart. Place the two

1

/4–20 hex nuts from inside the

cart and tighten. Refer to the illustration below.

ALIGNMENT

TOOL

SURFACES

FLUSH

UPPER

SCREW

SHOULDER

SCREWS

HEX NUT

(INSIDE CART)

Align back of shroud

Secure shroud

INSTALLATION

14

|

Wolf Customer Care 800.222.7820

Side Burner Installation

For natural gas installations, the gas line connection must

be made before installing the side burner.

INSTALL SIDE BURNER

1 Place the side burner into the shroud as shown in the

illustration below. Guide the exible gas line and wire

harness into the cart access hole. Verify alignment of the

unit prior to securing the side burner to the shroud. If

the side burner does not align properly, remove, loosen

screws, and check the shroud alignment with the tool.

Reposition the side burner until properly aligned.

2 Place a bar clamp with protected ends behind bullnose

on the re box and under the shroud. Do not include

any part of bullnose within the bar clamp. Refer to the

illustration below.

3 Compress the bar clamp until the hole in the bullnose

aligns with the threaded hole in the shroud. The align-

ment and placement of this screw is very important to

the side burner alignment. Refer to the illustration below.

4 Attach the side burner to the shroud by rst placing the

provided 8-32 hex cap screw into the right side of the

front underside of the bullnose and into the shroud. Then

place the left side hex cap screw. Tighten the screws

and remove the bar clamp.

5 At the rear of the unit, push the side burner toward the

grill to establish the proper gap at the rear. Loosen the

rear cart screws and shift the grill if necessary to achieve

the proper gap. Install the two provided 8-18 pan head

screws through the shroud and into the rear of the side

burner as shown in the illustration below. Verify proper

alignment.

INSTALLATION

ACCESS HOLE

Position side burner

Position bar clamp

HOLES

ALIGN

REAR

SCREWS

Hole alignment

Secure side burner

wolfappliance.com

|

15

Side Burner Installation

ELECTRICAL CONNECTION

1 Depending on the serial number of the grill, there may

be one or two connectors near the front of the grill

just above the manifold. Refer to the auxiliary harness

section for serial numbers. Locate the connector(s) by

looking above the manifold near the front of the grill.

2 Remove the unpopulated connector housing(s) from the

wire harness(es) coming from the grill as shown in the

illustration below.

3 Attach the appropriate connector housing(s) from the

side burner to the grill. Refer to the illustration below.

If only one connector is found on the grill, refer to the

auxiliary harness section for assembly of the second

connector housing.

INSTALLATION

UNPOPULATED

CONNECTORS

UNPOPULATED

CONNECTORS

AUXILLARY

HARNESS

Connectors

Connector housing

16

|

Wolf Customer Care 800.222.7820

Side Burner Installation

LP GAS CONNECTION

1 Connect the 2-stage LP gas regulator to the are tee at

the location shown. Connect the are swivel connector

to one end of the are tee. Refer to the illustration below.

2 Connect the regulator assembly to the exible gas line

coming into the grill cart from the side burner as shown

in the illustration below.

3 Connect the regulator assembly to the grill manifold at

the are swivel connector as shown in the illustration

below.

4 Reinstall the rear panel and door of the grill cart. Reposi-

tion the grill drip tray. Place the burner cap on the burner

head, place the grate on the burner pan, and afx the

knob to the bezel with the bezel nylon liner.

NATURAL GAS CONNECTION

1 Split the high pressure natural gas line into two lines,

one to attach to the grill natural gas regulator and one

to attach to the side burner via the exible line and

1

/2"

NPT adapter. Place the exible gas line through the cart

access hole.

2 Place the exible gas line through the cart access hole

and attach to the side burner regulator at the pipe elbow.

The elbow may be rotated to face downward for larger

adapters. Do not rotate the elbow upward. Refer to the

illustration below.

INSTALLATION

FLARE

SWIVEL

LP GAS

REGULATOR

FLARE

TEE

FLEXIBLE

GAS LINE

GRILL

MANIFOLD

LP gas regulator assembly

LP gas connection

Natural gas connection

wolfappliance.com

|

17

Side Burner Installation

AUXILIARY HARNESS (IF APPLICABLE)

If the Wolf outdoor grill has a serial number prior to the

numbers listed (OG30: 11364339, OG36: 11363946,

OG42: 11363911), an auxiliary harness will be provided

with the side burner. If not, contact Wolf Customer Care at

800-222-7820.

1 The upper rear panel of the grill cart must be removed

to install the auxiliary harness. Remove the rear panel by

removing the four screws.

2 With the provided wire ties, attach the auxiliary harness

to the re box n or existing wire harness. The 4-pin

connector cluster should be placed facing the rear of grill

and the 2-pin connector facing the front. The harness

must be tied down tightly and must not touch the grill re

box. Refer to the illustration below.

3 If connected, disconnect the transformer 4-pin con-

nector at the rear of the grill. Attach one of the 4-pin

connectors to the 4-pin connector attached to the grill.

Attach the other 4-pin connector to the 4-pin connector

from the transformer.

4 Remove the unpopulated connector housing from the

wire harness coming from the grill. Insert each con-

nector housing from the side burner harness to the

corresponding housing on the grill harness and on the

auxiliary harness. There are two connections to be made.

Refer to the illustrations below.

5 Reinstall the upper rear panel of the cart.

INSTALLATION

Auxiliary harness

UNPOPULATED

CONNECTORS

UNPOPULATED

CONNECTORS

AUXILLARY

HARNESS

Connectors

Connector housing

18

|

Wolf Customer Care 800.222.7820

TROUBLESHOOTING

Troubleshooting

IMPORTANT NOTE: If the outdoor gas grill does not operate

properly, follow these troubleshooting steps:

• Verify electrical power is supplied to the grill.

• Verify proper gas supply.

• Verify the gas supply shut-off valve is in the open

position.

• If the outdoor gas grill does not operate properly, contact

Wolf Factory Certied Service. Do not attempt to repair

the grill. Wolf is not responsible for service required to

correct a faulty installation.

Sub-Zero, Sub-Zero & Design, Sub-Zero & Snowake Design, Dual Refrigeration, The Living Kitchen, Great American Kitchens The Fine Art of Kitchen Design, Wolf, Wolf &

Design, Wolf Gourmet, W & Design, red colored knobs, Cove, and Cove & Design are registered trademarks and service marks of Sub-Zero Group, Inc. and its subsidiaries.

All other trademarks are property of their respective owners in the United States and other countries.