Ryobi TS1346 Le manuel du propriétaire

OPERATOR’S MANUAL

MANUEL D’UTILISATION

MANUAL DEL OPERADOR

10 in. COMPOUND

MITER SAW WITH LED

SCIE À ONGLETS COMPOSÉS DE

254 mm (10 po) AVEC DEL

SIERRA INGLETEADORA

COMBINADA DE 254 mm

(10 pulg.) CON GUÍA LED

TS1346

WARNING: To reduce the

risk of injury, the user must read and

understand the operator’s manual

before using this product.

SAVE THIS MANUAL FOR

FUTURE REFERENCE

ADVERTENCIA: Para reducir

el riesgo de lesiones, el usuario debe leer

y comprender el manual del operador

antes de usar este producto.

AVERTISSEMENT :

Pour

réduire les risques de blessures,

l’utilisateur doit lire et veiller à bien

comprendre le manuel d’utilisation avant

d’employer ce produit.

GUARDE ESTE MANUAL

PARA FUTURAS CONSULTAS

CONSERVER CE MANUEL

POUR FUTURE RÉFÉRENCE

TABLE OF CONTENTS

****************

General Safety Rules ...................... 2-3

Miter Saw Safety Rules .................. 3-4

Additional Safety Rules .................. 4-5

Symbols ..............................................6

Electrical ............................................. 7

Glossary of Terms ...............................8

Features ........................................ 9-11

Tools Needed ...................................12

Loose Parts List ................................12

Assembly .................................... 13-19

Operation .................................... 20-27

Adjustments .......................................2

Maintenance ............................... 29-30

Parts Ordering / Service ..... Back Page

TABLE DES MATIÈRES

****************

Règles de sécurité générales ......... 2-3

Règles de sécurité scie à onglets ... 3-4

Règles de sécurité supplémentaires ... 4-5

Symboles ............................................6

Caractéristiques électriques ...............7

Glossaire .............................................8

Caractéristiques ........................... 9-11

Outils nécessaires ............................12

Liste des pièces détachées ..............12

Assemblage ................................ 13-19

Utilisation .................................... 20-27

Réglages ...........................................28

Entretien ..................................... 29-30

Commande de pièces /

réparation ..........................Page arrière

ÍNDICE DE CONTENIDO

****************

Reglas de seguridad generales ...... 2-3

Reglas de seguridad sierra

ingleteadora ................................... 3-4

Advertencias de seguridad

adicionales ..................................... 4-5

Símbolos ............................................6

Aspectos eléctricos ............................ 7

Glosario de términos ..........................8

Características.............................. 9-11

Herramientas necesarias ..................12

Lista de piezas sueltas .....................12

Armado ....................................... 13-19

Funcionamiento .......................... 20-27

Ajustes ..............................................28

Mantenimiento ............................ 29-30

Pedidos de piezas /

servicio .......................... Pág. posterior

2 — English

GENERAL SAFETY RULES

WARNING:

Read all safety warnings, instructions, illustrations and

specifications provided with this power tool. Failure to

follow all instructions listed below may result in electric

shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-

operated (corded) power tool or battery-operated (cordless)

power tool.

WORK AREA SAFETY

Keep work area clean and well lit. Cluttered or dark

areas invite accidents.

Do not operate power tools in explosive atmospheres,

such as in the presence of flammable liquids, gases

or dust. Power tools create sparks which may ignite the

dust or fumes.

Keep children and bystanders away while operating a

power tool. Distractions can cause you to lose control.

ELECTRICAL SAFETY

Power tool plugs must match the outlet. Never modify

the plug in any way. Do not use any adapter plugs with

earthed (grounded) power tools. Unmodified plugs and

matching outlets will reduce risk of electric shock.

Avoid body contact with earthed or grounded surfaces,

such as pipes, radiators, ranges and refrigerators.

There is an increased risk of electric shock if your body

is earthed or grounded.

Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electric shock.

Do not abuse the cord. Never use the cord for carrying,

pulling or unplugging the power tool. Keep cord away

from heat, oil, sharp edges or moving parts. Damaged

or entangled cords increase the risk of electric shock.

When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electric shock.

If operating a power tool in a damp location is

unavoidable, use a ground fault circuit interrupter

(GFCI) protected supply. Use of a GFCI reduces the

risk of electric shock.

PERSONAL SAFETY

Stay alert, watch what you are doing and use common

sense when operating a power tool. Do not use a

power tool while you are tired or under the influence of

drugs, alcohol or medication. A moment of inattention

while operating power tools may result in serious personal

injury.

Use personal protective equipment. Always wear eye

protection. Protective equipment such as a dust mask,

non-skid safety shoes, hard hat or hearing protection

used for appropriate conditions will reduce personal

injuries.

Prevent unintentional starting. Ensure the switch is in

the off-position before connecting to power source

and/or battery pack, picking up or carrying the tool.

Carrying power tools with your finger on the switch or

energising power tools that have the switch on invites

accidents.

Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to

a rotating part of the power tool may result in personal

injury.

Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power tool

in unexpected situations.

Dress properly. Do not wear loose clothing or

jewellery. Keep your hair and clothing away from

moving parts. Loose clothes, jewellery or long hair can

be caught in moving parts.

If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection

can reduce dust-related hazards.

Do not let familiarity gained from frequent use of tools

allow you to become complacent and ignore tool

safety principles. A careless action can cause severe

injury within a fraction of a second.

POWER TOOL USE AND CARE

Do not force the power tool. Use the correct power

tool for your application. The correct power tool will

do the job better and safer at the rate for which it was

designed.

Do not use the power tool if the switch does not turn

it on and off. Any power tool that cannot be controlled

with the switch is dangerous and must be repaired.

Disconnect the plug from the power source and/

or remove the battery pack, if detachable, from the

power tool before making any adjustments, changing

accessories, or storing power tools. Such preventive

3 — English

GENERAL SAFETY RULES

MITER SAW SPECIFIC SAFETY RULES

Miter saws are intended to cut wood or wood-like

products, they cannot be used with abrasive cut-off

wheels for cutting ferrous material such as bars, rods,

studs, etc. Abrasive dust causes moving parts such as

the lower guard to jam. Sparks from abrasive cutting will

burn the lower guard, the kerf insert and other plastic

parts.

Use clamps to support the workpiece whenever

possible. If supporting the workpiece by hand, you

must always keep your hand at least 100 mm from

either side of the saw blade. Do not use this saw to

cut pieces that are too small to be securely clamped

or held by hand. If your hand is placed too close to the

saw blade, there is an increased risk of injury from blade

contact.

The workpiece must be stationary and clamped or

held against both the fence and the table. Do not feed

the workpiece into the blade or cut ”freehand” in any

way. Unrestrained or moving workpieces could be thrown

at high speeds, causing injury.

Never cross your hand over the intended line of cutting

either in front or behind the saw blade. Supporting the

workpiece ”cross handed” i.e. holding the workpiece to

the right of the saw blade with your left hand or vice versa

is very dangerous.

Do not reach behind the fence with either hand closer

than 100 mm from either side of the saw blade, to

remove wood scraps, or for any other reason while

the blade is spinning. The proximity of the spinning saw

blade to your hand may not be obvious and you may be

seriously injured.

Inspect your workpiece before cutting. If the

workpiece is bowed or warped, clamp it with the

outside bowed face toward the fence. Always make

certain that there is no gap between the workpiece,

fence and table along the line of the cut. Bent or warped

workpieces can twist or shift and may cause binding on

the spinning saw blade while cutting. There should be no

nails or foreign objects in the workpiece.

Do not use the saw until the table is clear of all tools,

wood scraps, etc., except for the workpiece. Small

debris or loose pieces of wood or other objects that

contact the revolving blade can be thrown with high

speed.

Cut only one workpiece at a time. Stacked multiple

workpieces cannot be adequately clamped or braced

and may bind on the blade or shift during cutting.

Ensure the miter saw is mounted or placed on a

level, firm work surface before use. A level and firm

work surface reduces the risk of the miter saw becoming

unstable.

Plan your work. Every time you change the bevel or

miter angle setting, make sure the adjustable fence

is set correctly to support the workpiece and will

not interfere with the blade or the guarding system.

Without turning the tool ”ON” and with no workpiece

on the table, move the saw blade through a complete

simulated cut to assure there will be no interference or

danger of cutting the fence.

safety measures reduce the risk of starting the power tool

accidentally.

Store idle power tools out of the reach of children and

do not allow persons unfamiliar with the power tool

or these instructions to operate the power tool. Power

tools are dangerous in the hands of untrained users.

Maintain power tools and accessories. Check for

misalignment or binding of moving parts, breakage

of parts and any other condition that may affect the

power tool’s operation. If damaged, have the power

tool repaired before use. Many accidents are caused

by poorly maintained power tools.

Keep cutting tools sharp and clean. Properly maintained

cutting tools with sharp cutting edges are less likely to

bind and are easier to control.

Use the power tool, accessories and tool bits etc.

in accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardous situation.

Keep handles and grasping surfaces dry, clean and

free from oil and grease. Slippery handles and grasping

surfaces do not allow for safe handling and control of the

tool in unexpected situations.

SERVICE

Have your power tool serviced by a qualified repair

person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained.

4 — English

MITER SAW SPECIFIC SAFETY RULES

Provide adequate support such as table extensions,

saw horses, etc. for a workpiece that is wider or longer

than the table top. Workpieces longer or wider than the

miter saw table can tip if not securely supported. If the

cut-off piece or workpiece tips, it can lift the lower guard

or be thrown by the spinning blade.

Do not use another person as a substitute for a table

extension or as additional support. Unstable support

for the workpiece can cause the blade to bind or the

workpiece to shift during the cutting operation pulling

you and the helper into the spinning blade.

The cut-off piece must not be jammed or pressed by

any means against the spinning saw blade. If confined,

i.e. using length stops, the cut-off piece could get wedged

against the blade and thrown violently.

Always use a clamp or a fixture designed to properly

support round material such as rods or tubing. Rods

have a tendency to roll while being cut, causing the blade

to bite and pull the work with your hand into the blade.

Let the blade reach full speed before contacting the

workpiece. This will reduce the risk of the workpiece

being thrown.

If the workpiece or blade becomes jammed, turn

the miter saw off. Wait for all moving parts to stop

and disconnect the plug from the power source and/

or remove the battery pack. Then work to free the

jammed material. Continued sawing with a jammed

workpiece could cause loss of control or damage to the

miter saw.

After finishing the cut, release the switch, hold the

saw head down and wait for the blade to stop before

removing the cut-off piece. Reaching with your hand

near the coasting blade is dangerous.

Hold the handle firmly when making an incomplete cut

or when releasing the switch before the saw head is

completely in the down position. The braking action of

the saw may to be suddenly pulled downward, causing

a risk of injury.

 Save these instructions. Refer to them frequently and

use to instruct other users. If you loan someone this tool,

loan them these instructions also.

 Use the proper extension cord. Make sure your

extension cord is in good condition. Use only a cord heavy

enough to carry the current your product will draw. An

undersized cord will cause a drop in line voltage resulting

in loss of power and overheating. A wire gauge size

(A.W.G.) of at least 14 is recommended for an extension

cord 25 feet or less in length. If in doubt, use the next

heavier gauge. The smaller the gauge number, the heavier

the cord.

 Inspect tool cords periodically. If damaged, have

repaired by a qualified service technician at an authorized

service facility. Repair or replace a damaged or worn cord

immediately. Stay constantly aware of cord location and

keep it well away from the rotating blade.

ADDITIONAL SAFETY RULES

 Inspect extension cords periodically and replace if

damaged.

 Polarized plugs. To reduce the risk of electric shock,

this tool has a polarized plug (one blade is wider than the

other). This plug will fit in a polarized outlet only one way.

If the plug does not fit fully in the outlet, reverse the plug.

If it still does not fit, contact a qualified electrician to install

the proper outlet. Do not change the plug in any way.

 Know your power tool. Read the operator’s manual

carefully. Learn the applications and limitations as well

as the specific potential hazards related to this tool.

 Always wear eye protection with side shields which

is marked to comply with ansi Z87.1 when using this

product. Failure to do so could result in objects being

thrown into your eyes, resulting in possible serious injury.

5 — English

ADDITIONAL SAFETY RULES

 Never stand on tool. Serious injury could occur if the tool

is tipped or if the cutting tool is unintentionally contacted.

 Keep guards in place and in good working order.

 Use the right direction of feed. Feed work into a blade,

cutter, or sanding spindle against the direction of rotation

of the blade, cutter, or sanding spindle only.

 Never leave tool running unattended. Turn the power

off. Don’t leave tool until it comes to a complete stop.

 Use only correct blades. Do not use blades with

incorrect size holes. Never use blade washers or blade

bolts that are defective or incorrect. The maximum blade

capacity of your saw is 10 in.

 Before making a cut, be sure all adjustments are

secure.

 Never touch blade or other moving parts during use.

 Double check all setups. Make sure blade is tight

and not making contact with saw or workpiece before

connecting to power supply.

 Firmly clamp or bolt your tool to a workbench or table

at approximately hip height.

 Make sure the miter table and saw arm (bevel function)

are locked in position before operating your saw. Lock

the miter table by pushing the miter lock lever down. Lock

the saw arm (bevel function) by securely tightening the

bevel lock knob.

 Never move the workpiece or make adjustment to any

cutting angle while the saw is running and the blade

is rotating. Any slip can result in contact with the blade

causing serious personal injury.

 Avoid awkward operations and hand positions where a

sudden slip could cause your hand to move into the blade.

ALWAYS make sure you have good balance. NEVER

operate your miter saw on the floor or in a crouched

position.

 Never stand or have any part of the body in line with the

path of the saw blade.

 Do not turn the motor switch on and off rapidly. This

could cause the saw blade to loosen and could create

a hazard. Should this ever occur, stand clear and allow

the saw blade to come to a complete stop. Disconnect

your saw from the power supply and securely retighten

the blade bolt.

 If any part of this miter saw is missing or should

break, bend, or fail in any way, or should any electrical

component fail to perform properly, shut off the power

switch, remove the miter saw plug from the power source

and have damaged, missing, or failed parts replaced

before resuming operation.

 Always turn off the saw before disconnecting it to avoid

accidental starting when reconnecting to power supply.

NEVER leave the saw unattended while connected to a

power source.

 This tool should have the following markings:

• To reduce the risk of injury, user must read the opera-

tor’s manual.

• Wear eye protection.

• Keep hands and body out of the path of the saw blade.

Contact with the blade will result in serious injury.

• Check guarding system to make sure it is functioning

correctly.

• Do not perform any operation freehand.

• Never reach around the saw blade.

• Turn off tool and wait for saw blade to stop before

moving workpiece or changing settings.

• Disconnect the saw from the power source before

changing blade or servicing.

 Always carry the tool only by the carrying handle.

 This saw can tip over if the saw head is released

suddenly and the saw is not secured to a work surface.

ALWAYS secure this saw to a stable work surface before

any use to avoid serious personal injury.

 Always make sure the saw blade has clearance of all

obstructions before turning the saw on.

6 — English

The following signal words and meanings are intended to explain the levels of risk associated with this product.

SYMBOL SIGNAL MEANING

DANGER: Indicates a hazardous situation, which, if not avoided, will result in death or

serious injury.

WARNING: Indicates a hazardous situation, which, if not avoided, could result in death or

serious injury.

CAUTION: Indicates a hazardous situation, that, if not avoided, may result in minor or

moderate injury.

NOTICE: (Without Safety Alert Symbol) Indicates information considered important, but

not related to a potential injury (e.g. messages relating to property damage).

SYMBOLS

Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper

interpretation of these symbols will allow you to operate the tool better and safer.

Safety Alert Indicates a potential personal injury hazard.

Read Operator’s Manual To reduce the risk of injury, user must read and understand opera-

tor’s manual before using this product.

Eye Protection Always wear eye protection with side shields marked to comply

with ANSI Z87.1.

No Hands Symbol Failure to keep your hands away from the blade will result in

serious personal injury.

Wet Conditions Alert Do not expose to rain or use in damp locations.

Extremely Bright Light This product uses extremely bright LEDs. To avoid serious eye

injury, do not stare into the light (not even from a distance).

V Volts Voltage

A Amperes Current

Hz Hertz Frequency (cycles per second)

min Minutes Time

Alternating Current Type of current

n

o

No Load Speed Rotational speed, at no load

Class II Construction Double-insulated construction

.../min Per Minute Revolutions, strokes, surface speed, orbits, etc., per minute

SYMBOL NAME DESIGNATION/EXPLANATION

7 — English

ELECTRICAL

DOUBLE INSULATION

Double insulation is a concept in safety in electric power tools,

which eliminates the need for the usual three-wire grounded

power cord. All exposed metal parts are isolated from the

internal metal motor components with protecting insulation.

Double insulated tools do not need to be grounded.

WARNING:

The double insulated system is intended to protect the

user from shock resulting from a break in the tool’s internal

wiring. Observe all normal safety precautions to avoid

electrical shock.

NOTE: Servicing of a product with double insulation requires

extreme care and knowledge of the system and should

be performed only by a qualified service technician. For

service, we suggest you return the tool to your nearest

authorized service center for repair. Always use original

factory replacement parts when servicing.

ELECTRICAL CONNECTION

This tool has a precision-built electric motor. It should be

connected to a power supply that is 120 V, AC only (normal

household current), 60 Hz. Do not operate this tool on

direct current (DC). A substantial voltage drop will cause a

loss of power and the motor will overheat. If the tool does

not operate when plugged into an outlet, double check the

power supply.

EXTENSION CORDS

When using a power tool at a considerable distance from

a power source, be sure to use an extension cord that has

the capacity to handle the current the product will draw. An

undersized cord will cause a drop in line voltage, resulting in

overheating and loss of power. Use the chart to determine

the minimum wire size required in an extension cord. Only

round jacketed cords listed by Underwriter’s Laboratories

(UL) should be used.

When working outdoors with a product, use an extension

cord that is designed for outside use. This type of cord is

designated with “WA” or “W” on the cord’s jacket.

Before using any extension cord, inspect it for loose or

exposed wires and cut or worn insulation.

**Ampere rating (on product data plate)

0-2.0 2.1-3.4 3.5-5.0 5.1-7.0 7.1-12.0 12.1-16.0

Cord Length Wire Size (A.W.G.)

25’ 16 16 16 16 14 14

50’ 16 16 16 14 14 12

100’ 16 16 14 12 10 —

**Used on 12 gauge - 20 amp circuit.

NOTE: AWG = American Wire Gauge

WARNING:

Keep the extension cord clear of the working area.

Position the cord so that it will not get caught on lumber,

tools, or other obstructions while you are working with a

power tool. Failure to do so can result in serious personal

injury.

WARNING:

Check extension cords before each use. If damaged

replace immediately. Never use tool with a damaged cord

since touching the damaged area could cause electrical

shock resulting in serious injury.

8 — English

GLOSSARY OF TERMS

Pilot hole (drill presses and scroll saws)

A small hole drilled in a workpiece that serves as a guide

for drilling large holes accurately or for insertion of a scroll

saw blade.

Push blocks (jointer planers)

Device used to feed the workpiece over the jointer planer

cutterhead during any operation. This aid helps keep the

operator’s hands well away from the cutterhead.

Push blocks and push sticks (table saws)

Devices used to feed the workpiece through the saw blade

during cutting operations. When making a narrow rip cut

without a jig or similar cutting aid, always use a push stick (not

a push block). A push block can be used for narrow ripping

operations, if a jig or similar cutting aid is used. These aids

help keep the operator’s hands well away from the blade.

Rabbet

A non-through cut positioned on the end or edge of the

workpiece which produces a square, two-sided notch or

trough in the workpiece.

Resaw (table saws and band saws)

A cutting operation to reduce the thickness of the workpiece

to make thinner pieces.

Resin

A sticky, sap-based substance that has hardened.

Revolutions per minute (RPM)

The number of turns completed by a spinning object in one

minute.

Ripping or rip cut (table saws)

A cutting operation along the length of the workpiece and

typically in the direction of the grain.

Riving knife/spreader/splitter (table saws)

A metal piece, slightly thinner than the blade, which helps

keep the kerf open and also helps to prevent kickback.

Saw blade path

The area over, under, behind, or in front of the blade. As it

applies to the workpiece, that area which will be or has been

cut by the blade.

Snipe (planers)

Depression made at either end of a workpiece by cutter

blades when the workpiece is not properly supported.

Taper cut

A cut where the material being cut has a different width at

the beginning of the cut from the end.

Through sawing

Any cutting operation where the blade extends completely

through the thickness of the workpiece. This type of cut will

separate a single workpiece into two pieces.

Workpiece or material

The item on which the operation is being done.

Worktable

Surface where the workpiece rests while performing a cutting,

drilling, planing, or sanding operation.

Anti-kickback pawls (radial arm and table saws)

A device which, when properly installed and maintained,

is designed to stop the workpiece from being kicked back

toward the front of the saw during a ripping operation.

Arbor

The shaft on which a blade or cutting tool is mounted.

Bevel cut

A cutting operation made with the blade at any angle other

than 90° to the table surface.

Chamfer

A cut removing a wedge from a block so the end (or part of

the end) is angled rather than at 90°.

Compound cut

A cross cut made with both a miter and a bevel angle.

Cross cut

A cutting or shaping operation made across the grain or the

width of the workpiece.

Cutter head (planers and jointer planers)

A rotating cutterhead with adjustable blades or knives. The

blades or knives remove material from the workpiece.

Dado cut (table saws and compound sliding miter saws)

A non-through cut which produces a square, three-sided

notch or trough in the workpiece.

Featherboard (table saws)

A device used to help control the workpiece by guiding

it securely against the table or fence during any ripping

operation.

FPM or SPM

Feet per minute (or strokes per minute), used in reference

to blade movement.

Freehand

Performing a cut without the workpiece being guided by a

fence, miter fence, or other aids.

Gum

A sticky, sap-based residue from wood products.

Heel

Alignment of the blade to the miter gauge groove.

Kerf

The material removed by the blade in a through cut or the

slot produced by the blade in a non-through or partial cut.

Kickback

A hazard that can occur when the blade binds or stalls,

throwing the workpiece in the direction of the spinning blade.

Miter cut

A cutting operation made with the workpiece at any angle

to the blade other than 90°.

Non-through cuts (table saws and compound sliding

miter saws)

Any cutting operation where the blade does not extend

completely through the thickness of the workpiece. This is a

cut where the blade will not cut the workpiece into two pieces.

9 — English

FEATURES

PRODUCT SPECIFICATIONS

Blade arbor ................................................................ 5/8 in.

Blade diameter ............................................................10 in.

No load speed .........................................5,500 /min. (RPM)

Input ............................................. 120 V~, 60 Hz, 14 Amps

Cutting capacity with miter at 0°/bevel 0°:

Maximum nominal lumber sizes: ....... 2 x 6 in., 4 x 4 in.

Cutting capacity with miter at 45°/bevel 0°:

Maximum nominal lumber sizes: ...................... 2 x 4 in.

Cutting capacity with miter at 0°/bevel 45°:

Maximum nominal lumber sizes: ...................... 2 x 6 in.

Cutting capacity with miter at 45°/bevel 45°:

Maximum nominal lumber sizes: ...................... 2 x 4 in.

Fig. 1

LOWER

BLADE GUARD

“D” HANDLE

MITER

LOCK HANDLE

“NO HANDS ZONE”

LABEL

“NO HANDS ZONE”

BOUNDARY LINE

MITER

SCALE

UPPER

BLADE GUARD

TRIGGER

LOCKOUT LEVER

SWITCH

TRIGGER

LED

SWITCH

MITER

FENCE

BEVEL

LOCK KNOB

THROAT

PLATE

CONTROL

ARM

BASE

MITER

TABLE

BLADE

WRENCH

DUST

BAG

WORK

CLAMP

PARTIAL

SLIDING FENCE

10 — English

FEATURES

KNOW YOUR COMPOUND MITER SAW

See Figure 1.

The safe use of this product requires an understanding of

the information on the tool and in this operator’s manual as

well as a knowledge of the project you are attempting. Before

use of this product, familiarize yourself with all operating

features and safety rules.

10 in. BLADE

A 10 in. blade is included with the compound miter saw.

It will cut materials up to 3-1/2 in. thick or 5-1/2 in. wide,

depending on the angle at which the cut is being made.

BEVEL LOCK KNOB

See Figure 2.

The bevel lock knob securely locks your compound miter

saw at desired bevel angles. A positive stop adjustment

screw has been provided on each side of the saw arm.

These adjustment screws are for making fine adjustments

at 0° and 45°.

“D” HANDLE

See Figure 3.

For convenience when carrying or transporting the miter saw

from one place to another, a “D” handle has been provided.

To transport, turn off and unplug the saw, then lower the saw

arm and lock it in the down position by pushing the lock pin in.

NOTE: DO NOT perform any cutting operation with the saw

in the locked position.

ELECTRIC BRAKE

An electric brake has been provided to quickly stop blade

rotation after the switch is released.

LED LIGHTING SYSTEM

The LED casts a shadow of the blade teeth onto the workpiece

for making precision cuts and predicts blade kerf for blade

cut line.

MITER FENCE

The miter fence on the compound miter saw has been

provided to hold the workpiece securely against when

making all cuts.

MITER LOCK HANDLE

See Figure 3.

The miter lock handle securely locks the saw at desired

miter angles.

Fig. 2

SAW ARM LOCKED IN DOWN POSITION

MITER

LOCK HANDLE

LOCK

Fig. 3

“D”

HANDLE

LED GUIDE

SWITCH

BEVEL

LOCK

KNOB

11 — English

SPINDLE

LOCK

BUTTON

PADLOCK

SWITCH

TRIGGER

Fig. 4

FEATURES

PARTIAL SLIDING FENCE

The partial sliding fence on your compound miter saw has

been provided to help secure the workpiece when making

straight cuts.

The sliding feature makes it easy to adjust the position of the

partial fence. Loosen the fence screw before attempting to

slide the partial fence. Once the desired position is determined,

tighten the fence screw to secure.

POSITIVE STOPS ON MITER TABLE

Positive stops have been provided at 0°, 15°, 22-1/2°, 31.6°,

and 45° on both the left and right side of the miter table.

SELF-RETRACTING LOWER BLADE GUARD

The lower blade guard is made of shock-resistant, see-

through plastic that provides protection from each side of

the blade. It retracts over the upper blade guard as the saw

is lowered into the workpiece.

SPINDLE LOCK BUTTON

See Figure 4.

The spindle lock button locks the spindle stopping the

blade from rotating. Depress and hold the lock button while

installing, changing, or removing blade.

SWITCH TRIGGER

See Figure 4.

The saw will not start until you depress the trigger lockout lever

and squeeze the switch trigger. To prevent unauthorized use

of the compound miter saw, disconnect it from the power

supply and lock the switch in the OFF position. To lock the

switch, install a padlock (not included) through the hole in

the switch trigger and make certain the switch is inoperable.

If the switch is still operable with the padlock installed, a

padlock with a larger shackle diameter must be used. Store

the padlock key in another location.

SWITCH

TRIGGER

LOCKOUT LEVER

12 — English

LOOSE PARTS

WARNING:

The use of attachments or accessories not listed might be hazardous and could cause serious personal injury.

BLADE

WRENCH

MITER

LOCK HANDLE

WORK

CLAMP

DUST BAG

TOOLS NEEDED

The following tools (not included) are needed for making adjustments or installing the blade:

Fig. 5

Fig. 6

COMBINATION

SQUARE

 Miter lock handle

 Dust bag

 Work clamp

 Blade wrench

 Operator’s manual (not shown)

The following items are included with the tool:

13 — English

ASSEMBLY

Fig. 7

MOUNTING

SURFACE

BASE

TRACE HOLES

AT THESE LOCATIONS

FOR HOLE PATTERN

TRACE HOLES

AT THESE LOCATIONS

FOR HOLE PATTERN

WARNING:

If any parts are damaged or missing do not operate this

tool until the parts are replaced. Use of this product

with damaged or missing parts could result in serious

personal injury.

WARNING:

Do not attempt to modify this tool or create accessories

not recommended for use with this tool. Any such

alteration or modification is misuse and could result in a

hazardous condition leading to possible serious personal

injury.

WARNING:

Do not connect to power supply until assembly is

complete. Failure to comply could result in accidental

starting and possible serious personal injury.

WARNING:

Do not start the compound miter saw without checking

for interference between the blade and the miter fence.

Damage could result to the blade if it strikes the miter

fence during operation of the saw.

WARNING:

This saw can tip over if the saw head is released suddenly

and the saw is not secured to a work surface. ALWAYS

secure this saw to a stable work surface before any use

to avoid serious personal injury.

UNPACKING

This product requires assembly.

 Carefully lift saw from the carton by the carrying handle

and the saw base, and place it on a level work surface.

WARNING:

Do not use this product if any parts on the Loose Parts list

are already assembled to your product when you unpack

it. Parts on this list are not assembled to the product by

the manufacturer and require customer installation. Use

of a product that may have been improperly assembled

could result in serious personal injury.

 This saw has been shipped with the saw arm secured in the

down position. To release the saw arm, push down on the

“D” handle, cut the tie-wrap, and pull out on the lock pin.

WARNING:

The saw arm is spring loaded. Hold the handle down to

prevent it from snapping up when cutting the tie-wrap.

Failure to do so could result in possible serious injury.

 Lift the saw arm by the “D” handle. Hand pressure should

remain on the saw arm to prevent sudden rise upon

release of the tie wrap.

 Inspect the tool carefully to make sure no breakage or

damage occurred during shipping.

 Do not discard the packing material until you have carefully

inspected and satisfactorily operated the tool.

 The saw is factory set for accurate cutting. After assembling

it, check for accuracy. If shipping has influenced the

settings, refer to specific procedures explained in this

manual.

 If any parts are damaged or missing, please call

1-800-525-2579 for assistance.

14 — English

ASSEMBLY

Fig. 8

Fig. 9

TO

LOOSEN

MITER

LOCK HANDLE

TO

TIGHTEN

MOUNTING HOLES

See Figure 7.

WARNING:

Before starting any cutting operation, clamp or bolt

your miter saw to a workbench or an approved miter

saw stand. If a miter saw stand is used, read operator’s

manual and follow the instructions for the miter saw

stand. Never operate your miter saw on the floor or in a

crouched position. Failure to heed this warning can result

in serious personal injury.

The compound miter saw should be mounted to a firm

supporting surface such as a workbench, mounting board,

or miter saw stand. The saw base has four mounting holes.

If using bolts or screws, they should be of sufficient length

to accommodate the saw base, lock washers, hex nuts, and

the thickness of the workbench or other mounting surface.

Tighten all bolts or screws securely.

The hole pattern for mounting to a workbench is shown in

figure 7. Carefully check the workbench after mounting to

make sure that no movement can occur during use. If any

tipping, sliding, or walking is noted, secure the workbench

to the floor before operating.

MITER LOCK HANDLE

See Figure 8.

To install the miter lock handle, place the threaded stud on

the end of the miter lock handle into the threaded hole in

the control arm. Turn clockwise to tighten.

LOCKING/UNLOCKING THE SAW ARM

See Figure 9.

To unlock and raise the saw arm:

 Firmly grasp the “D” handle and apply downward

pressure while at the same time pulling the lock pin out

and away from the saw housing.

 Release the lock pin and slowly raise the saw arm.

To lock the saw arm:

 Firmly grasp the “D” handle and apply downward

pressure while at the same time pushing the lock pin in

and toward the saw housing.

 Release the lock pin allowing it to lock the saw into place.

DUST BAG

See Figure 10.

A dust bag is provided for use on the miter saw. It fits over

the exhaust port on the upper blade guard. Squeeze the two

metal clips to open the mouth of the bag and slide it on the

exhaust port. Release the clips. The metal ring in the bag

should lock in between the grooves on the exhaust port.

To remove the dust bag for emptying, simply reverse the

above procedure.

CONTROL ARM

“D”

HANDLE

DUST

BAG

EXHAUST

PORT Fig. 10

LOCK

15 — English

Fig. 11

ASSEMBLY

Fig. 12

WORK

CLAMP

BASE

BLADE

WRENCH

BLADE WRENCH

See Figure 11.

A blade wrench is included with this saw. One end of the

wrench is a Phillips screwdriver and the other end is a hex

key. Use the hex key end when installing or removing blade

and the Phillips end when removing or loosening screws.

A storage area for the blade wrench is located on the back

of the miter fence.

WORK CLAMP

See Figure 11.

WARNING:

In some operations, the work clamp assembly may

interfere with the operation of the blade guard assembly.

Always make sure there is no interference with the blade

guard prior to beginning any cutting operation to reduce

the risk of serious personal injury.

The work clamp provides greater control by clamping the

workpiece to the fence. It also prevents the workpiece from

creeping toward the saw blade. This is very helpful when

cutting compound miters.

Depending on the cutting operation and the size of the

workpiece, it may be necessary to use a C-clamp or other

suitable clamp instead of the work clamp to secure the

workpiece to the miter table prior to making the cut.

To install the work clamp:

Place the shaft of the work clamp in either hole on the

miter table base.

 Rotate the knob on the work clamp clockwise to move it

in or counterclockwise to move it out as needed.

TO INSTALL/REPLACE THE BLADE

See Figures 12 - 13.

The blade is shipped installed on this miter saw model.

Instructions have been included for reference when changing

or replacing blades.

WARNING:

A 10 in. blade is the maximum blade capacity of the saw.

Never use a blade that is too thick to allow outer blade

washer to engage with the flats on the arbor. Larger

blades will come in contact with the blade guards, while

thicker blades will prevent the blade bolt from securing

the blade on the arbor. Either of these situations could

result in a serious accident and can cause serious

personal injury.

 Unplug the saw.

 Raise saw arm.

SPINDLE

LOCK BUTTON

16 — English

ASSEMBLY

 Using the Phillips screwdriver end of the blade wrench,

loosen, but do not remove, the blade bolt cover screw.

Rotate lower blade guard and blade bolt cover up and

back to expose the blade bolt.

 Depress and hold the spindle lock button and rotate the

blade bolt until the spindle locks.

 Using the hex end of the blade wrench, loosen and remove

the blade bolt.

NOTE: The blade bolt has left-hand threads. Turn blade

bolt clockwise to loosen.

 Remove outer blade washer. Do not remove inner blade

washer.

 Wipe a drop of oil onto inner blade washer and outer

blade washer where they contact the blade.

WARNING:

If inner blade washer has been removed, replace it before

placing blade on spindle. Failure to do so could cause an

accident since blade will not tighten properly.

 Fit saw blade inside lower blade guard and onto spindle.

The blade teeth point downward at the front of saw as

shown in figure 13.

 Replace outer blade washer. The double “D” flats on the

blade washers align with the flats on the spindle.

 Depress and hold spindle lock button and replace blade

bolt.

NOTE: The blade bolt has left-hand threads. Turn blade bolt

counterclockwise to tighten.

CAUTION:

Always install the blade with the blade teeth and the arrow

printed on the side of the blade pointing down at the front

of the saw. The direction of blade rotation is also stamped

with an arrow on the upper blade guard.

 Tighten blade bolt securely.

 Replace the blade bolt cover and tighten blade bolt cover

screw securely.

 Lower blade guard.

 Raise and lower the saw arm to ensure lower blade guard

functions correctly.

WARNING:

Make sure the spindle lock button is not engaged before

reconnecting saw into power source. Never engage

spindle lock button when blade is rotating.

BLADE

BOLT

Fig. 13

LOWER

BLADE GUARD

BLADE

TO

TIGHTEN

TO

LOOSEN

FLAT(S)

ON SPINDLE

BLADE

BOLT

COVER

NOTE : BEFORE USE,

ENSURE SCREW IS

TIGHTENED SECURELY

TO PREVENT GUARD

MOVEMENT

OUTER BLADE

WASHER WITH

DOUBLE “D”

FLATS

INNER BLADE WASHER WITH

DOUBLE “D” FLATS

BLADE BOLT

COVER SCREW

BLADE

BOLT

OUTER

BLADE

WASHER

BLADE

ARBOR

INNER

BLADE

WASHER

17 — English

ASSEMBLY

NOTE: Many of the illustrations in this manual show only

portions of the compound miter saw. This is intentional so that

we can clearly show points being made in the illustrations.

Never operate the saw without all guards securely in

place and in good operating condition.

SQUARING THE SAW BLADE TO THE FENCE

See Figures 14 - 19.

 Unplug the saw.

 Pull the saw arm all the way down and engage the lock

pin to hold the saw arm in transport position.

 Loosen the miter lock handle approximately one-half turn.

 Rotate the miter table until the scale indicator on the

control arm is positioned at 0°.

 Securely tighten the miter lock handle.

 Loosen bevel lock knob and set saw arm at 0° bevel

(blade set 90° to miter table). Tighten bevel lock knob.

 Lay a framing square flat on the miter table. Place one

leg of the square against the fence. Slide the other leg

of the square against the flat part of saw blade.

NOTE: Make sure that the square contacts the flat part

of the saw blade, not the blade teeth.

Fig. 14

VIEW OF BLADE SQUARE WITH FENCE

MITER

LOCK HANDLE

MITER

LOCK HANDLE

MITER

LOCK HANDLE

MITER

TABLE

MITER

TABLE

MITER

TABLE

BLADE

FRAMING

SQUARE

FRAMING

SQUARE

FRAMING

SQUARE

MITER

FENCE

MITER

FENCE

MITER

FENCE

 The edge of the square and the saw blade should be

parallel as shown in figure 14.

 If the front or back edge of the saw blade angles away

from the square as shown in figures 15 - 16, adjustments

are needed.

Fig. 15

Fig. 16

VIEW OF BLADE NOT SQUARE WITH FENCE,

ADJUSTMENTS ARE REQUIRED

VIEW OF BLADE NOT SQUARE WITH FENCE,

ADJUSTMENTS ARE REQUIRED

18 — English

ASSEMBLY

 Loosen the fence screw and slide the partial sliding miter

fence toward the blade to access the socket head screws

securing the left miter fence to the table.

 Loosen the socket head screws that secure the miter

fence to the saw base.

 Rotate the miter fence left or right until the saw blade is

parallel with the square.

 Retighten the screws securely and recheck the blade-to-

fence alignment.

 Return the partial sliding miter fence to the home position

and retighten the fence screw to secure.

Your saw has several scale indicators. After squaring

adjustments have been made, it may be necessary to

loosen the indicator screws and reset them to zero. See

Figures 18 and 19.

Fig. 17

SOCKET HEAD

SCREW(S)

MITER

FENCE

Fig. 18

Fig. 19

INDICATOR

SCREW

SCALE

INDICATOR

MITER

SCALE

INDICATOR

SCREW

BEVEL

SCALE

INDICATOR

PARTIAL

SLIDING

MITER

FENCE

SCREW

19 — English

Fig. 20

CORRECT VIEW OF BLADE

SQUARE WITH MITER TABLE

MITER

TABLE

MITER

TABLE

MITER

TABLE

MITER

LOCK

HANDLE

COMBINATION

SQUARE

COMBINATION

SQUARE

COMBINATION

SQUARE

BLADE

BEVEL

LOCK KNOB

POSITIVE STOP

ADJUSTMENT SCREWS

ASSEMBLY

SQUARING THE BLADE TO THE MITER TABLE

See Figures 20 - 22.

 Unplug the saw.

 Pull the saw arm all the way down and engage the lock

pin to hold the saw arm in transport position.

 Loosen the miter lock handle approximately one-half turn.

 Rotate the miter table until the scale indicator on the

control arm is positioned at 0°.

 Securely tighten the miter lock handle.

 Loosen bevel lock knob and set saw arm at 0° bevel

(blade set 90° to miter table). Tighten bevel lock knob.

 Place a combination square against the miter table and

the flat part of saw blade.

NOTE: Make sure that the square contacts the flat part

of the saw blade, not the blade teeth.

 Rotate the blade by hand and check the blade-to-table

alignment at several points.

 The edge of the square and the saw blade should be

parallel as shown in figure 20.

 If the top or bottom of the saw blade angles away from

the square as shown in figures 21 and 22, adjustments

are needed.

 Loosen bevel lock knob.

Fig. 21

Fig. 22

VIEW OF BLADE NOT SQUARE WITH MITER

TABLE, ADJUSTMENTS ARE REQUIRED

VIEW OF BLADE NOT SQUARE WITH MITER TABLE,

ADJUSTMENTS ARE REQUIRED

 Adjust positive stop adjustment screw to bring saw

blade into alignment with the square. See Positive Stop

Adjustment in the Adjustment section.

 Retighten bevel lock knob. Recheck blade-to-table

alignment.

NOTE: The above procedure can be used to check blade

squareness of the saw blade to the miter table at both 0°

and 45° angles.

Your saw has several scale indicators. After squaring adjust-

ments have been made, it may be necessary to loosen the

indicator screws and reset them to zero. See Figures 18 and 19.

20 — English

OPERATION

WARNING:

Do not allow familiarity with tools to make you careless.

Remember that a careless fraction of a second is

sufficient to inflict serious injury.

WARNING:

Always wear eye protection with side shields marked to

comply with ANSI Z87.1. Failure to do so could result in

objects being thrown into your eyes, resulting in possible

serious injury.

WARNING:

Do not use any attachments or accessories not

recommended by the manufacturer of this tool. The use

of attachments or accessories not recommended can

result in serious personal injury.

APPLICATIONS

This product has been designed only for the purposes listed

below:

 Cross cutting wood, wood composition and plastic (do

not cut metals, ceramics, or masonry products.)

 Cross cutting miters, joints, etc. for picture frames

moldings, door casings, and fine joinery

 Bevel cutting and compound cutting of lumber and moldings

NOTE: The blade provided is fine for most wood cutting

operations, but for fine joinery cuts or cutting plastic, use

one of the accessory blades available from the dealer.

WARNING:

Before starting any cutting operation, clamp or bolt the

compound miter saw to a workbench. Never operate the

miter saw on the floor or in a crouched position. Failure

to heed this warning can result in serious personal injury.

WARNING:

To avoid serious personal injury, always tighten the miter

lock handle and bevel lock knob securely before making

a cut. Failure to do so could result in movement of the

control arm or miter table while making a cut.

WARNING:

To avoid serious personal injury, keep hands outside

the no hands zone, at least 4 in. from the blade. Never

perform any cutting operation freehand (without holding

workpiece against the fence). The blade could grab the

workpiece if it slips or twists.

NOTICE:

Do not start the compound miter saw without checking

for interference between the blade and the miter fence.

Damage could result to the blade if it strikes the miter

fence during operation of the saw.

CUTTING WITH YOUR COMPOUND

MITER SAW

WARNING:

When using a work clamp or C-clamp to secure your

workpiece, clamp workpiece on one side of the blade

only. The workpiece must remain free on one side of the

blade to prevent the blade from binding in workpiece. The

workpiece binding the blade will cause motor stalling and

kickback. This situation could cause an accident resulting

in possible serious personal injury.

WARNING:

NEVER move the workpiece or make adjustment to any

cutting angle while the saw is running and the blade is

rotating. Any slip can result in contact with the blade

causing serious personal injury.

LED LIGHTING SYSTEM

See Figure 23.

WARNING:

Do not stare into the light beam (not even from a dis-

tance). Staring into the light beam may result in serious

injury or vision loss.

The LED lighting system casts the shadow of the blade onto

the workpiece. This results in greater accuracy of cuts and

requires no adjustments.

To use this feature, turn the LED switch on.

Bring the saw arm down so that the blade is approximately

1/4 in. from the workpiece. The shadow of the blade will be

projected onto the workpiece, indicating where the blade

teeth will make contact as the cut is made.

La page charge ...

Ryobi TS1346 Le manuel du propriétaire

Ryobi TS1346 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents