Ryobi P553 Le manuel du propriétaire

OPERATOR’S MANUAL

MANUEL D’UTILISATION

MANUAL DEL OPERADOR

7-1/4 in., 18 VOLT MITER SAW

SCIE À ONGLETS DE 184 mm

(7-1/4 po), 18 V

SIERRA INGLETEADORA

DE 184 mm (7-1/4 pulg.), 18 V

P553

WARNING: To reduce the

risk of injury, the user must read and

understand the operator’s manual

before using this product.

SAVE THIS MANUAL FOR

FUTURE REFERENCE

ADVERTENCIA: Para reducir

el riesgo de lesiones, el usuario debe leer

y comprender el manual del operador

antes de usar este producto.

AVERTISSEMENT :

Pour

réduire les risques de blessures,

l’utilisateur doit lire et veiller à bien

comprendre le manuel d’utilisation avant

d’employer ce produit.

GUARDE ESTE MANUAL

PARA FUTURAS CONSULTAS

CONSERVER CE MANUEL

POUR FUTURE RÉFÉRENCE

TABLE OF CONTENTS

****************

 General Safety Rules .......................2-3

 Miter Saw Safety Rules ...................3-4

 Additional Safety Rules ...................4-5

 Symbols ..............................................6

 Glossary of Terms ...............................7

 Features .........................................8-10

 Tools Needed ...................................10

 Loose Parts List ................................11

 Assembly .....................................11-18

 Operation .....................................18-26

 Adjustments .....................................27

 Maintenance ..................................... 28

 Parts Ordering / Service ..... Back Page

TABLE DES MATIÈRES

****************

 Règles de sécurité générales ..........2-3

 Règles de sécurité scie à onglets ....3-4

 Règles de sécurité supplémentaires ...4-5

 Symboles ............................................6

 Glossaire .............................................7

 Caractéristiques ............................8-10

 Outils nécessaires ............................10

 Liste des pièces détachées ..............11

 Assemblage .................................11-18

 Utilisation .....................................18-26

 Réglages ...........................................27

 Entretien ...........................................28

 Commande de pièces /

réparation ..........................Page arrière

ÍNDICE DE CONTENIDO

****************

 Reglas de seguridad generales .......2-3

 Reglas de seguridad sierra

ingleteadora ....................................3-4

Advertencias de seguridad

adicionales ......................................4-5

 Símbolos ............................................6

 Glosario de términos ..........................7

 Características ..............................8-10

 Herramientas necesarias ..................10

 Lista de piezas sueltas .....................11

 Armado ........................................11-18

 Funcionamiento ...........................18-26

 Ajustes ..............................................27

 Mantenimiento ..................................28

 Pedidos de piezas /

servicio .......................... Pág. posterior

2 – English

GENERAL SAFETY RULES

WARNING:

Read all safety warnings, instructions, illustrations and

specifications provided with this power tool. Failure to

follow all instructions listed below may result in electric

shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-

operated (corded) power tool or battery-operated (cordless)

power tool.

WORK AREA SAFETY

Keep work area clean and well lit. Cluttered or dark areas

invite accidents.

Do not operate power tools in explosive atmospheres,

such as in the presence of flammable liquids, gases or

dust. Power tools create sparks which may ignite the dust

or fumes.

Keep children and bystanders away while operating a

power tool. Distractions can cause you to lose control.

ELECTRICAL SAFETY

Power tool plugs must match the outlet. Never modify

the plug in any way. Do not use any adapter plugs with

earthed (grounded) power tools. Unmodified plugs and

matching outlets will reduce risk of electric shock.

Avoid body contact with earthed or grounded surfaces,

such as pipes, radiators, ranges and refrigerators.

There is an increased risk of electric shock if your body is

earthed or grounded.

Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of electric

shock.

Do not abuse the cord. Never use the cord for carrying,

pulling or unplugging the power tool. Keep cord away

from heat, oil, sharp edges or moving parts. Damaged

or entangled cords increase the risk of electric shock.

When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electric shock.

If operating a power tool in a damp location is

unavoidable, use a ground fault circuit interrupter

(GFCI) protected supply. Use of a GFCI reduces the risk

of electric shock.

PERSONAL SAFETY

Stay alert, watch what you are doing and use common

sense when operating a power tool. Do not use a power

tool while you are tired or under the influence of drugs,

alcohol or medication. A moment of inattention while

operating power tools may result in serious personal injury.

Use personal protective equipment. Always wear eye

protection. Protective equipment such as dust mask, non-

skid safety shoes, hard hat, or hearing protection used for

appropriate conditions will reduce personal injuries.

Prevent unintentional starting. Ensure the switch is in

the off-position before connecting to power source

and/or battery pack, picking up or carrying the tool.

Carrying power tools with your finger on the switch or

energising power tools that have the switch on invites

accidents.

Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to a

rotating part of the power tool may result in personal injury.

Do not overreach. Keep proper footing and balance at

all times. This enables better control of the power tool in

unexpected situations.

Dress properly. Do not wear loose clothing or jewellery.

Keep your hair, clothing and gloves away from moving

parts. Loose clothes, jewellery or long hair can be caught

in moving parts.

If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection can

reduce dust-related hazards.

Do not let familiarity gained from frequent use of tools

allow you to become complacent and ignore tool safety

principles. A careless action can cause severe injury within

a fraction of a second.

POWER TOOL USE AND CARE

Do not force the power tool. Use the correct power tool

for your application. The correct power tool will do the

job better and safer at the rate for which it was designed.

Do not use the power tool if the switch does not turn it

on and off. Any power tool that cannot be controlled with

the switch is dangerous and must be repaired.

Disconnect the plug from the power source and/

or remove the battery pack, if detachable, from the

power tool before making any adjustments, changing

accessories, or storing power tools. Such preventive

safety measures reduce the risk of starting the power tool

accidentally.

Store idle power tools out of the reach of children and

do not allow persons unfamiliar with the power tool

or these instructions to operate the power tool. Power

tools are dangerous in the hands of untrained users.

Maintain power tools and accessories. Check for

misalignment or binding of moving parts, breakage

of parts and any other condition that may affect the

power tool’s operation. If damaged, have the power

tool repaired before use. Many accidents are caused by

poorly maintained power tools.

3 – English

GENERAL SAFETY RULES

Keep cutting tools sharp and clean. Properly maintained

cutting tools with sharp cutting edges are less likely to bind

and are easier to control.

Use the power tool, accessories and tool bits etc.

in accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardous situation.

Keep handles and grasping surfaces dry, clean and

free from oil and grease. Slippery handles and grasping

surfaces do not allow for safe handling and control of the

tool in unexpected situations.

BATTERY TOOL USE AND CARE

Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type

of battery pack may create a risk of fire when used with

another battery pack.

Use battery only with charger listed. For use with 18 V

lithium-ion battery packs, see tool/appliance/battery pack/

charger correlation supplement 987000-432.

Use power tools only with specifically designated

battery packs. Use of any other battery packs may create

a risk of injury and fire.

When battery pack is not in use, keep it away from

other metal objects, like paper clips, coins, keys, nails,

screws or other small metal objects, that can make a

connection from one terminal to another. Shorting the

battery terminals together may cause burns or a fire.

Under abusive conditions, liquid may be ejected from

the battery; avoid contact. If contact accidentally

occurs, flush with water. If liquid contacts eyes,

additionally seek medical help. Liquid ejected from the

battery may cause irritation or burns.

Do not use a battery pack or tool that is damaged or

modified. Damaged or modified batteries may exhibit

unpredictable behavior resulting in fire, explosion, or risk

of injury.

Do not expose a battery pack or tool to fire or excessive

temperature. Exposure to fire or temperature above 265°

F may cause explosion.

Follow all charging instructions and do not charge the

battery pack or tool outside the temperature range

specified in the instructions. Charging improperly or at

temperatures outside the specified range may damage the

battery and increase the risk of fire.

Battery tools do not have to be plugged into an

electrical outlet; therefore, they are always in operating

condition. Be aware of possible hazards when not

using your battery tool or when changing accessories.

Following this rule will reduce the risk of electric shock, fire,

or serious personal injury.

Do not place battery tools or their batteries near fire

or heat. This will reduce the risk of explosion and possibly

injury.

 Do not crush, drop or damage battery pack. Do not

use a battery pack or charger that has been dropped

or received a sharp blow. A damaged battery is subject

to explosion. Properly dispose of a dropped or damaged

battery immediately.

Batteries can explode in the presence of a source

of ignition, such as a pilot light. To reduce the risk of

serious personal injury, never use any cordless product

in the presence of open flame. An exploded battery can

propel debris and chemicals. If exposed, flush with water

immediately.

Do not charge battery tool in a damp or wet location.

Do not use, store, or charge battery packs or products

in locations where the temperature is less than 50°F or

more than 100°F. Do not store outside or in vehicles.

Under extreme usage or temperature conditions,

battery leakage may occur. If liquid comes in contact

with your skin, wash immediately with soap and water.

If liquid gets into your eyes, flush them with clean water

for at least 10 minutes, then seek immediate medical

attention. Following this rule will reduce the risk of serious

personal injury.

SERVICE

Have your power tool serviced by a qualified repair

person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained.

MITER SAW SPECIFIC SAFETY RULES

Miter saws are intended to cut wood or wood-like

products, they cannot be used with abrasive cut-off

wheels for cutting ferrous material such as bars, rods,

studs, etc. Abrasive dust causes moving parts such as the

lower guard to jam. Sparks from abrasive cutting will burn

the lower guard, the kerf insert and other plastic parts.

Use clamps to support the workpiece whenever

possible. If supporting the workpiece by hand, you must

always keep your hand at least 100 mm from either side

of the saw blade. Do not use this saw to cut pieces that

are too small to be securely clamped or held by hand.

If your hand is placed too close to the saw blade, there is

an increased risk of injury from blade contact.

4 – English

MITER SAW SPECIFIC SAFETY RULES

The workpiece must be stationary and clamped or held

against both the fence and the table. Do not feed the

workpiece into the blade or cut “freehand” in any way.

Unrestrained or moving workpieces could be thrown at high

speeds, causing injury.

Never cross your hand over the intended line of cutting

either in front or behind the saw blade. Supporting the

workpiece “cross handed” i.e. holding the workpiece to

the right of the saw blade with your left hand or vice versa

is very dangerous.

Do not reach behind the fence with either hand closer

than 100 mm from either side of the saw blade, to

remove wood scraps, or for any other reason while

the blade is spinning. The proximity of the spinning saw

blade to your hand may not be obvious and you may be

seriously injured.

Inspect your workpiece before cutting. If the workpiece

is bowed or warped, clamp it with the outside bowed

face toward the fence. Always make certain that there

is no gap between the workpiece, fence and table along

the line of the cut. Bent or warped workpieces can twist

or shift and may cause binding on the spinning saw blade

while cutting. There should be no nails or foreign objects

in the workpiece.

Do not use the saw until the table is clear of all tools,

wood scraps, etc., except for the workpiece. Small

debris or loose pieces of wood or other objects that contact

the revolving blade can be thrown with high speed.

Cut only one workpiece at a time. Stacked multiple

workpieces cannot be adequately clamped or braced and

may bind on the blade or shift during cutting.

Ensure the miter saw is mounted or placed on a level,

firm work surface before use. A level and firm work surface

reduces the risk of the miter saw becoming unstable.

Plan your work. Every time you change the bevel or

miter angle setting, make sure the adjustable fence

is set correctly to support the workpiece and will not

interfere with the blade or the guarding system. Without

turning the tool ”ON” and with no workpiece on the table,

move the saw blade through a complete simulated cut to

assure there will be no interference or danger of cutting the

fence.

Provide adequate support such as table extensions,

saw horses, etc. for a workpiece that is wider or longer

than the table top. Workpieces longer or wider than the

miter saw table can tip if not securely supported. If the cut-

off piece or workpiece tips, it can lift the lower guard or be

thrown by the spinning blade.

Do not use another person as a substitute for a table

extension or as additional support. Unstable support for

the workpiece can cause the blade to bind or the workpiece

to shift during the cutting operation pulling you and the

helper into the spinning blade.

The cut-off piece must not be jammed or pressed by

any means against the spinning saw blade. If confined,

i.e. using length stops, the cut-off piece could get wedged

against the blade and thrown violently.

Always use a clamp or a fixture designed to properly

support round material such as rods or tubing. Rods

have a tendency to roll while being cut, causing the blade

to bite and pull the work with your hand into the blade.

Let the blade reach full speed before contacting the

workpiece. This will reduce the risk of the workpiece being

thrown.

If the workpiece or blade becomes jammed, turn the

miter saw off. Wait for all moving parts to stop and

disconnect the plug from the power source and/or

remove the battery pack. Then work to free the jammed

material. Continued sawing with a jammed workpiece

could cause loss of control or damage to the miter saw.

After finishing the cut, release the switch, hold the

saw head down and wait for the blade to stop before

removing the cut-off piece. Reaching with your hand near

the coasting blade is dangerous.

Hold the handle firmly when making an incomplete cut

or when releasing the switch before the saw head is

completely in the down position. The braking action of

the saw may to be suddenly pulled downward, causing a

risk of injury.

 Save these instructions. Refer to them frequently and use

to instruct other users. If you loan someone this tool, loan

them these instructions also.

ADDITIONAL SAFETY RULES

 Use the proper extension cord. Make sure your extension

cord is in good condition. Use only a cord heavy enough

to carry the current your product will draw. An undersized

cord will cause a drop in line voltage resulting in loss of

power and overheating. A wire gauge size (A.W.G.) of at

least 14 is recommended for an extension cord 25 feet or

less in length. If in doubt, use the next heavier gauge. The

smaller the gauge number, the heavier the cord.

 Inspect tool cords periodically. If damaged, have

repaired by a qualified service technician at an authorized

service facility. Repair or replace a damaged or worn cord

immediately. Stay constantly aware of cord location and

keep it well away from the rotating blade.

 Inspect extension cords periodically and replace if

damaged.

5 – English

 Polarized plugs. To reduce the risk of electric shock,

this tool has a polarized plug (one blade is wider than the

other). This plug will fit in a polarized outlet only one way.

If the plug does not fit fully in the outlet, reverse the plug.

If it still does not fit, contact a qualified electrician to install

the proper outlet. Do not change the plug in any way.

 Know your power tool. Read the operator’s manual

carefully. Learn the applications and limitations as well

as the specific potential hazards related to this tool.

 Always wear eye protection with side shields which

is marked to comply with ansi Z87.1 when using this

product. Failure to do so could result in objects being

thrown into your eyes, resulting in possible serious injury.

 Never stand on tool. Serious injury could occur if the tool

is tipped or if the cutting tool is unintentionally contacted.

 Keep guards in place and in good working order.

 Use the right direction of feed. Feed work into a blade,

cutter, or sanding spindle against the direction of rotation

of the blade, cutter, or sanding spindle only.

 Never leave tool running unattended. Turn the power

off. Don’t leave tool until it comes to a complete stop.

 Use only correct blades. Do not use blades with

incorrect size holes. Never use blade washers or blade

bolts that are defective or incorrect. The maximum blade

capacity of your saw is 7-1/4 in.

 Before making a cut, be sure all adjustments are

secure.

 Never touch blade or other moving parts during use.

 Double check all setups. Make sure blade is tight

and not making contact with saw or workpiece before

connecting to power supply.

 Firmly clamp or bolt your tool to a workbench or table

at approximately hip height.

 Make sure the miter table and saw arm (bevel function)

are locked in position before operating your saw. Lock

the miter table by pushing the miter lock knob down. Lock

the saw arm (bevel function) by securely tightening the

bevel lock knob.

 Never move the workpiece or make adjustment to any

cutting angle while the saw is running and the blade

is rotating. Any slip can result in contact with the blade

causing serious personal injury.

 Avoid awkward operations and hand positions where a

sudden slip could cause your hand to move into the blade.

ALWAYS make sure you have good balance. NEVER

operate your miter saw on the floor or in a crouched

position.

 Never stand or have any part of the body in line with the

path of the saw blade.

 Do not turn the motor switch on and off rapidly. This

could cause the saw blade to loosen and could create

a hazard. Should this ever occur, stand clear and allow

the saw blade to come to a complete stop. Disconnect

your saw from the power supply and securely retighten

the blade bolt.

 If any part of this miter saw is missing or should

break, bend, or fail in any way, or should any electrical

component fail to perform properly, shut off the power

switch, remove the miter saw plug from the power source

and have damaged, missing, or failed parts replaced

before resuming operation.

 Always turn off the saw before disconnecting it to avoid

accidental starting when reconnecting to power supply.

NEVER leave the saw unattended while connected to a

power source.

 This tool should have the following markings:

• To reduce the risk of injury, user must read the opera-

tor’s manual.

• Wear eye protection.

• Keep hands and body out of the path of the saw blade.

Contact with the blade will result in serious injury.

• Check guarding system to make sure it is functioning

correctly.

• Do not perform any operation freehand.

• Never reach around the saw blade.

• Turn off tool and wait for saw blade to stop before

moving workpiece or changing settings.

• Disconnect the saw from the power source before

changing blade or servicing.

 Always carry the tool only by the carrying handle.

 This saw can tip over if the saw head is released

suddenly and the saw is not secured to a work surface.

ALWAYS secure this saw to a stable work surface before

any use to avoid serious personal injury.

 Always make sure the saw blade has clearance of

all obstructions before turning the saw on.

ADDITIONAL SAFETY RULES

6 – English

SYMBOLS

The following signal words and meanings are intended to explain the levels of risk associated with this product.

SYMBOL SIGNAL MEANING

DANGER:

Indicates a hazardous situation, which, if not avoided, will result in death or

serious injury.

WARNING:

Indicates a hazardous situation, which, if not avoided, could result in death or

serious injury.

CAUTION:

Indicates a hazardous situation, that, if not avoided, may result in minor or

moderate injury.

NOTICE:

(Without Safety Alert Symbol) Indicates information considered important, but

not related to a potential injury (e.g. messages relating to property damage).

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper

interpretation of these symbols will allow you to operate the product better and safer.

SYMBOL NAME DESIGNATION/EXPLANATION

Safety Alert Indicates a potential personal injury hazard.

Read Operator’s

Manual

To reduce the risk of injury, user must read and understand operator’s manual

before using this product.

Eye Protection

Always wear eye protection with side shields marked to comply with ANSI

Z87.1.

No Hands Symbol

Failure to keep your hands away from the blade will result in

serious personal injury.

Wet Conditions

Alert

Do not expose to rain or use in damp locations.

Recycle Symbols

This product uses lithium-ion (Li-ion) batteries. Local, state or federal laws

may prohibit disposal of batteries in ordinary trash. Consult your local waste

authority for information regarding available recycling and/or disposal options.

V Volts Voltage

min Minutes Time

Direct Current Type or a characteristic of current

n

o

No Load Speed Rotational speed, at no load

.../min Per Minute Revolutions, strokes, surface speed, orbits etc., per minute

7 – English

GLOSSARY OF TERMS

Pilot Hole (drill presses and scroll saws)

A small hole drilled in a workpiece that serves as a guide

for drilling large holes accurately or for insertion of a scroll

saw blade.

Push Blocks (jointer planers)

Device used to feed the workpiece over the jointer planer

cutterhead during any operation. This aid helps keep the

operator’s hands well away from the cutterhead.

Push Blocks and Push Sticks (table saws)

Devices used to feed the workpiece through the saw blade

during cutting operations. When making a narrow rip cut

without a jig or similar cutting aid, always use a push stick (not

a push block). A push block can be used for narrow ripping

operations, if a jig or similar cutting aid is used. These aids

help keep the operator’s hands well away from the blade.

Rabbet

A non-through cut positioned on the end or edge of the

workpiece which produces a square, two-sided notch or

trough in the workpiece.

Resaw (table saws and band saws)

A cutting operation to reduce the thickness of the workpiece

to make thinner pieces.

Resin

A sticky, sap-based substance that has hardened.

Revolutions Per Minute (RPM)

The number of turns completed by a spinning object in one

minute.

Ripping or Rip Cut (table saws)

A cutting operation along the length of the workpiece and

typically in the direction of the grain.

Riving Knife/Spreader/Splitter (table saws)

A metal piece, slightly thinner than the blade, which helps

keep the kerf open and also helps to prevent kickback.

Saw Blade Path

The area over, under, behind, or in front of the blade. As it

applies to the workpiece, that area which will be or has been

cut by the blade.

Snipe (planers)

Depression made at either end of a workpiece by cutter

blades when the workpiece is not properly supported.

Taper Cut

A cut where the material being cut has a different width at

the beginning of the cut from the end.

Through Sawing

Any cutting operation where the blade extends completely

through the thickness of the workpiece. This type of cut will

separate a single workpiece into two pieces.

Workpiece or Material

The item on which the operation is being done.

Worktable

Surface where the workpiece rests while performing a cutting,

drilling, planing, or sanding operation.

Anti-Kickback Pawls (radial arm and table saws)

A device which, when properly installed and maintained,

is designed to stop the workpiece from being kicked back

toward the front of the saw during a ripping operation.

Arbor

The shaft on which a blade or cutting tool is mounted.

Bevel Cut

A cutting operation made with the blade at any angle other

than 90° to the table surface.

Chamfer

A cut removing a wedge from a block so the end (or part of

the end) is angled rather than at 90°.

Compound Cut

A cross cut made with both a miter and a bevel angle.

Cross Cut

A cutting or shaping operation made across the grain or the

width of the workpiece.

Cutter Head (planers and jointer planers)

A rotating cutterhead with adjustable blades or knives. The

blades or knives remove material from the workpiece.

Dado Cut (table saws and compound sliding miter saws)

A non-through cut which produces a square, three-sided

notch or trough in the workpiece.

Featherboard (table saws)

A device used to help control the workpiece by guiding

it securely against the table or fence during any ripping

operation.

FPM or SPM

Feet per minute (or strokes per minute), used in reference

to blade movement.

Freehand

Performing a cut without the workpiece being guided by a

fence, miter fence, or other aids.

Gum

A sticky, sap-based residue from wood products.

Heel

Alignment of the blade to the miter gauge groove.

Kerf

The material removed by the blade in a through cut or the

slot produced by the blade in a non-through or partial cut.

Kickback

A hazard that can occur when the blade binds or stalls,

throwing the workpiece in the direction of the spinning blade.

Miter Cut

A cutting operation made with the workpiece at any angle

to the blade other than 90°.

Non-Through Cuts (table saws and compound sliding

miter saws)

Any cutting operation where the blade does not extend

completely through the thickness of the workpiece. This is a

cut where the blade will not cut the workpiece into two pieces.

8 – English

FEATURES

Fig. 1

PRODUCT SPECIFICATIONS

Arbor ......................................................................... 5/8 in.

Blade Diameter ...................................................... 7-1/4 in.

No Load Speed (RPM) ......................................4,000 /min

Motor .................................................................. 18 Volt DC

Cutting Capacity with Miter at 0°/Bevel 0°:

Maximum lumber sizes ..................... 1-1/2 in. x 4-1/4 in.

Cutting Capacity with Miter at 45°/Bevel 0°:

Maximum lumber sizes ............................1-1/2 in. x 3 in.

Cutting Capacity with Miter at 0°/Bevel 45°:

Maximum lumber sizes ............................ 1 in. x 4-1/4 in.

and 1-1/2 in. x 3-1/2 in.

Cutting Capacity with Miter at 45°/Bevel 45°:

Maximum lumber sizes .................................. 1 in. x 3 in.

LOWER

BLADE GUARD

UPPER

BLADE GUARD

BLADE

WRENCH STORAGE

“D”

HANDLE

BASE

BEVEL

LOCK KNOB

“NO HANDS

ZONE” LABEL

LOCK PIN

MITER

SCALE

BLADE

WRENCH

MITER TABLE

DUST BAG

WORK

CLAMP

BEVEL

SCALE

MITER

FENCE

MITER

LOCK KNOB

DETENT

RELEASE BUTTON

“NO HANDS ZONE”

BOUNDARY LINE

TRIGGER

LOCKOUT LEVER

CONTROL

ARM

THROAT

PLATE

SWITCH

TRIGGER

PARTIAL

SLIDING FENCE

REAR BRACKET

SIDE

HANDLE AREA

9 – English

DETENT

RELEASE BUTTON

FEATURES

KNOW YOUR COMPOUND MITER SAW

See Figure 1.

The safe use of this product requires an understanding of

the information on the tool and in this operator’s manual as

well as a knowledge of the project you are attempting. Before

use of this product, familiarize yourself with all operating

features and safety rules.

7-1/4 in. BLADE

A 7-1/4 in. blade is included with the compound miter saw.

It will cut materials up to 1-1/2 in. thick or 4-1/4 in. wide,

depending upon the angle at which the cut is being made.

BEVEL LOCK KNOB

See Figure 2.

The bevel lock knob securely locks your compound miter

saw at desired bevel angles. Loosen the bevel lock knob

to release the saw allowing the blade to be tilted for bevel

cuts. Tighten the knob to lock the saw in place. Positive stop

adjustment screws are located on each side of the saw arm.

These adjustment screws are for making fine adjustments

at 0° and 45°.

BLADE WRENCH STORAGE

A blade wrench is packed with the saw. One end of the

wrench is a phillips screwdriver and the other end is a hex

key. Use the hex key end when installing or removing blade

and the phillips end when removing or loosening screws. A

storage area for the blade wrench is located in the saw’s base.

HANDLE AREAS

See Figure 2.

For convenience when carrying or transporting the miter saw

from one place to another, use the handle areas on either side

of the saw base. To transport, turn off the saw and remove

the battery pack, then lower the saw arm and lock it in the

down position. Lock saw arm by pushing the lock pin in.

NOTE: DO NOT perform any cutting operation with the saw

in the locked position.

MITER FENCE

The miter fence on the compound miter saw is used to secure

your workpiece when making all cuts.

MITER LOCK KNOB

See Figure 3.

The miter lock knob securely locks the saw at desired miter

angles. Turn the knob clockwise to lock the saw in place.

To release the saw, turn the the knob counterclockwise and

depress the detent release button.

Fig. 3

TO

LOOSEN

MITER

LOCK KNOB

TO

TIGHTEN

SAW ARM LOCKED IN DOWN POSITION

LOCK PIN

BEVEL

LOCK KNOB

“D”

HANDLE

PARTIAL

SLIDING FENCE

REAR BRACKET

BLADE

WRENCH

SIDE

HANDLE

AREA

PARTIAL SLIDING FENCE

The partial sliding fence on your compound miter saw has

been provided to help secure the workpiece when making

straight cuts.

The sliding feature makes it easy to adjust the position of

the partial fence. Loosen the fence screw before attempt-

ing to slide the partial fence. Once the desired position is

determined, tighten the fence screw to secure.

10 – English

FEATURES

The following tools (not included) are needed for making adjustments:

TOOLS NEEDED

FRAMING SQUARE

COMBINATION SQUARE

Fig. 4

Fig. 3

SPINDLE

LOCK BUTTON

TRIGGER

LOCKOUT

LEVER

SWITCH TRIGGER

PAD LOCK

POSITIVE STOPS ON MITER TABLE

Positive stops have been provided at 0°, 15°, 22.5°, 31.6°,

and 45° on both the left and right side of the miter table.

SELF-RETRACTING LOWER BLADE GUARD

See Figure 3.

The lower blade guard is made of shock-resistant, see-

through plastic that provides protection from each side of

the blade. It retracts over the upper blade guard as the saw

is lowered into the workpiece.

SPINDLE LOCK BUTTON

See Figure 3.

The spindle lock button locks the spindle, stopping the

blade from rotating. Depress and hold the lock button while

installing, changing, or removing the blade.

SWITCH TRIGGER

See Figure 3.

The saw will not start until you depress the trigger lockout

lever and squeeze the switch trigger. To prevent unauthorized

use of the compound miter saw, remove the battery pack

from the tool and lock the switch in the off position. To lock

the switch, install a padlock (not included) through the hole in

the switch trigger and make certain the switch is inoperable.

If the switch is still operable with the padlock installed, a

padlock with a larger shackle diameter must be used. Store

the padlock key in another location.

LOWER

BLADE GUARD

11 – English

LOOSE PARTS LIST

WARNING:

The use of attachments or accessories not listed might be hazardous and could cause serious personal injury.

WORK

CLAMP

DUST BAG

BLADE

WRENCH

Fig. 5

The following items are included with your compound miter saw:

 Dust Bag

 Work Clamp

 Blade Wrench

 Rear Bracket

 Operator’s Manual (not shown)

ASSEMBLY

UNPACKING

This product requires assembly.

 Carefully lift miter saw base from the carton by the “D”

handle and the saw base, and place it on a level work

surface.

WARNING:

Do not use this product if any parts on the Loose Parts List

are already assembled to your product when you unpack

it. Parts on this list are not assembled to the product by

the manufacturer and require customer installation. Use

of a product that may have been improperly assembled

could result in serious personal injury.

 This saw has been shipped with the saw arm secured in

the down position. To release the saw arm, push down

on the top of the saw arm, cut the tie-wrap, and pull out

the lock pin.

WARNING:

The saw arm is spring loaded. Hold the handle down

to prevent from snapping up when cutting the tie-wrap.

Failure to do so could result in possible serious injury.

 Lift the saw arm by the “D” handle. Hand pressure should

remain on the saw arm to prevent sudden rise upon

release of the tie wrap.

 Inspect the tool carefully to make sure no breakage or

damage occurred during shipping.

 Do not discard the packing material until you have carefully

inspected and satisfactorily operated the tool.

MITER

LOCK KNOB

REAR

BRACKET

BEVEL LOCK

KNOB

WASHER

12 – English

ASSEMBLY

WARNING:

This saw can tip over if the saw head is released suddenly

and the saw is not secured to a work surface. ALWAYS

secure this saw to a stable work surface before any use

to avoid serious personal injury.

MOUNTING HOLES

See Figure 6.

WARNING:

Before starting any cutting operation, clamp or bolt

your miter saw to a workbench or an approved miter

saw stand. If a miter saw stand is used, read operator’s

manual and follow the instructions for the miter saw

stand. Never operate your miter saw on the floor or in a

crouched position. Failure to heed this warning can result

in serious personal injury.

The compound miter saw should be mounted to a firm

supporting surface such as a workbench, mounting board,

or miter saw stand. The saw base has four mounting holes.

If using bolts or screws, they should be of sufficient length

to accommodate the saw base, lock washers, hex nuts, and

the thickness of the workbench or other mounting surface.

Tighten all bolts or screws securely.

The hole pattern for mounting to a workbench is shown in

figure 6. Carefully check the workbench after mounting to

make sure that no movement can occur during use. If any

tipping, sliding, or walking is noted, secure the workbench

to the floor before operating.

 The saw is factory set for accurate cutting. After assembling

it, check for accuracy. If shipping has influenced the

settings, refer to specific procedures explained in this

manual.

 If any parts are damaged or missing, please call

1-800-525-2579 for assistance.

WARNING:

If any parts are damaged or missing do not operate this

product until the parts are replaced. Use of this product

with damaged or missing parts could result in serious

personal injury.

WARNING:

Do not attempt to modify this tool or create accessories

not recommended for use with this tool. Any such

alteration or modification is misuse and could result in a

hazardous condition leading to possible serious personal

injury.

WARNING:

To prevent accidental starting that could cause serious

personal injury, always remove the battery pack from the

tool when assembling parts.

WARNING:

Do not start the compound miter saw without checking

for interference between the blade and the miter fence.

Damage could result to the blade if it strikes the miter

fence during operation of the saw.

TRACE HOLES

AT THESE LOCATIONS

FOR HOLE PATTERN

TRACE HOLES

AT THESE LOCATIONS

FOR HOLE PATTERN

Fig. 6

MOUNTING

SURFACE

BASE

13 – English

ASSEMBLY

INSTALLING THE MITER LOCK KNOB

See Figure 7.

To install the miter lock knob, place the threaded stud on

the end of the miter lock knob into the threaded hole in the

control arm. Turn clockwise to tighten.

LOCKING / UNLOCKING THE SAW ARM

See Figure 7.

To unlock and raise the saw arm:

 Firmly grasp the “D” handle and apply downward pressure

while at the same time pulling the lock pin out and away

from the saw housing.

 Release the lock pin and slowly raise the saw arm.

To lock the saw arm:

 Firmly grasp the “D” handle and apply downward pressure

while at the same time pushing the lock pin in and toward

the saw housing.

 Release the lock pin allowing it to lock the saw into place.

INSTALLING THE REAR BRACKET

See Figure 8.

WARNING:

A rear bracket is included with this miter saw to prevent

tipping if the saw arm is released suddenly. Do not use

this saw before installing the rear bracket and securely

mounting the saw to a work surface or stand.

Remove the screws from the Rear Bracket and set aside.

Slide the bracket in the openings on the saw base,

aligning the holes underneath the base with the holes in

the bracket.

Insert the screws into the holes and tighten securely.

INSTALLING THE BEVEL LOCK KNOB

See Figure 8.

To install the bevel lock knob, slide the washer onto the

threaded stud on the end of the bevel lock knob then place

the knob into the threaded hole on the back of the saw. Turn

clockwise to tighten.

BLADE WRENCH

See Figure 8.

A blade wrench is included with this saw. One end of the

wrench is a phillips screwdriver and the other end is a hex

key. Use the hex key end when installing or removing blade

and the phillips end when removing or loosening screws. A

storage area for the blade wrench is located on the back of

the left miter fence.

Fig. 7

Fig. 8

REAR BRACKET

SCREW

BLADE

WRENCH

STORAGE

“D”

HANDLE

LOCK PIN

Fig 9

DUST BAG

EXHAUST

PORT

MITER LOCK KNOB

CONTROL ARM

DUST BAG

See Figure 9.

A dust bag is provided for use on this miter saw. It fits over the

exhaust port on the upper blade guard. To install, squeeze the

two metal clips to open the mouth of the bag and slide it on the

exhaust port. Release the clips. The metal ring in the bag should

lock in between the grooves on the exhaust port. To remove the

dust bag for emptying, simply reverse the above procedure.

BEVEL LOCK KNOB

WASHER

14 – English

ASSEMBLY

WORK CLAMP

See Figure 10.

WARNING:

In some operations, the work clamp assembly may

interfere with the operation of the blade guard assembly.

Always make sure there is no interference with the blade

guard prior to beginning any cutting operation to reduce

the risk of serious personal injury.

The work clamp provides greater control by clamping the

workpiece to the fence. It also prevents the workpiece from

creeping toward the saw blade. This is very helpful when

cutting compound miters. Depending on the cutting operation

and the size of the workpiece, it may be necessary to use a

C-clamp or other suitable clamp instead of the work clamp

to secure the workpiece to the miter table prior to making

the cut.

To install the work clamp:

Place the shaft of the work clamp in either hole on the

saw table base.

 Rotate the knob on the work clamp to move it up or down

as needed.

TO INSTALL/REPLACE THE BLADE

See Figures 11 - 12.

The blade is shipped installed on this miter saw model.

Instructions have been included for reference when changing

or replacing blades.

WARNING:

A 7-1/4 in. blade is the maximum blade capacity of the

saw. Never use a blade that is too thick to allow outer blade

washer to engage with the flats on the spindle. Larger

blades will come in contact with the blade guards, while

thicker blades will prevent the blade bolt from securing the

blade on the spindle. Either of these situations could result

in a serious accident and can cause serious personal injury.

 Remove the battery pack from the saw.

 Raise the saw arm.

 Rotate lower blade guard up and back to expose the

blade bolt.

NOTE: Raise the blade guard until resistance is met and

continue to raise the guard until it reaches the locked

open position.

 Depress and hold the spindle lock button and rotate the

blade bolt until the spindle locks.

 Using the hex end of the blade wrench, loosen and

remove the blade bolt.

NOTE: The blade bolt has left hand threads. Turn blade

bolt clockwise to loosen.

Fig. 11

BASE

WORK

CLAMP

Fig. 10

SPINDLE LOCK

BUTTON

WORK

CLAMP KNOB

15 – English

THROAT

PLATE

ASSEMBLY

 Remove outer blade washer.

NOTE: The inner blade washer is integrated into the

spindle and cannot be removed.

 Wipe a drop of oil onto spindle and outer blade washer

where they contact the blade.

 Fit saw blade inside lower blade guard and onto spindle.

The blade teeth point downward at the front of saw as

shown in figure 12.

 Replace outer blade washer. The double “D” flats on blade

washers align with flats on spindle.

 Depress and hold spindle lock button and replace blade

bolt.

NOTE: The blade bolt has left hand threads. Turn blade bolt

counterclockwise to tighten.

CAUTION:

Always install the blade with the blade teeth and the arrow

printed on the side of the blade pointing down at the front

of the saw. The direction of blade rotation is also stamped

with an arrow on the upper blade guard.

 Tighten blade bolt securely.

 Lower the blade guard.

 Raise and lower the saw arm to ensure lower blade guard

functions correctly.

REMOVING/REPLACING THE THROAT PLATE

See Figure 13.

WARNING:

The throat plate must be below the miter table. If the

throat plate is too high or too low, the workpiece can

catch on the uneven edges resulting in binding which

could result in serious personal injury.

Never operate the saw without a throat plate installed.

To remove/replace:

 Remove the battery pack from the saw.

 Remove the screws securing the throat plate.

 Lift the throat plate from the saw.

 To reinstall the throat plate, align the holes in the throat

plate with the holes in the saw base.

 Retighten the screws, being careful not to overtighten

which can cause the throat plate to bow or bend.

NOTE: Many of the illustrations in this manual show only

portions of the compound miter saw. This is intentional so

that we can clearly show points being made in the illustra-

tions. Never operate the saw without all guards securely

in place and in good operating condition.

Fig. 12

Fig. 13

OUTER

BLADE WASHER

BLADE

BOLT

SPINDLE

BLADE

BOLT

LOWER BLADE GUARD

BLADE

TO

LOOSEN

FLAT(S)

ON SPINDLE

OUTER BLADE

WASHER WITH

DOUBLE “D” FLATS

TO

TIGHTEN

16 – English

VIEW OF BLADE NOT SQUARE WITH FENCE,

ADJUSTMENTS ARE REQUIRED

ASSEMBLY

Fig. 14

SQUARING THE BLADE TO THE FENCE

See Figures 14 - 19.

 Remove the battery pack from the saw.

 Pull the saw arm all the way down and engage the lock

pin to hold the saw arm in transport position.

 Loosen the miter lock knob approximately one-half turn

and press the detent release button.

 Rotate the miter table until the pointer aligns with zero

dentent on the miter scale.

 Release the detent release button, engaging the positive

stop notch, then tighten the miter lock knob to secure the

miter table.

 Loosen bevel lock knob and set saw arm at 0° bevel

(blade set 90° to miter table). Tighten bevel lock knob.

 Lay a square flat on the miter table. Place one leg of the

square against the fence. Slide the other leg of the square

against the flat part of saw blade.

NOTE: Make sure that the square contacts the flat part

of the saw blade, not the blade teeth.

 The edge of the square and the saw blade should be

parallel as shown in figure 14.

 If the front or back edge of the saw blade angles away

from the square as shown in figures 15 - 16, adjustments

are needed.

 Loosen the fence screw and slide the partial sliding miter

fence toward the blade to access the socket head screws

securing the left miter fence to the table.

 Using the blade wrench, loosen the socket head screws

that secure the miter fence to the miter table.

MITER

TABLE

MITER

FENCE

BLADE

FRAMING

SQUARE

VIEW OF BLADE SQUARE WITH FENCE

 Rotate the miter fence left or right until the saw blade is

parallel with the square.

 Retighten the screws securely and recheck the blade-to-

fence alignment.

 Return the partial sliding miter fence to the home position

and retighten the fence screw to secure.

VIEW OF BLADE NOT SQUARE WITH FENCE,

ADJUSTMENTS ARE REQUIRED

Fig. 15

Fig. 16

MITER

FENCE

MITER

FENCE

MITER

TABLE

MITER

TABLE

BLADE

FRAMING

SQUARE

FRAMING

SQUARE

17 – English

CORRECT VIEW OF BLADE

SQUARE WITH MITER TABLE

ASSEMBLY

The saw has two scale indicators, one on the bevel scale and

one on the miter scale. After squaring adjustments have been

made, it may be necessary to loosen the indicator screws

and reset them to zero. See figures 18 - 19.

SQUARING THE BLADE TO THE MITER TABLE

See Figures 20-22.

 Remove the battery pack from the saw.

 Pull the saw arm all the way down and engage the lock

pin to hold the saw arm in transport position.

 Loosen the miter lock knob to unlock the miter table.

 Rotate the miter table until the pointer aligns with zero

detent on the miter scale.

 Tighten the miter lock knob to lock the miter table.

MITER FENCE

SOCKET HEAD

SCREW(S)

SOCKET HEAD

SCREW(S)

SCALE

INDICATOR

SCREWS

BEVEL

SCALE

Fig. 17

Fig. 18

Fig. 20

 Loosen bevel lock knob and set saw arm at 0

°

bevel (blade

set 90

°

to miter table). Tighten bevel lock knob at stop.

 Place a square against the miter table and the flat part

of saw blade.

NOTE: Make sure that the square contacts the flat part

of the saw blade, not the blade teeth.

 Rotate the blade by hand and check the blade-to-table

alignment at several points.

 The edge of the square and the saw blade should be

parallel as shown in figure 20.

 If the top or bottom of the saw blade angles away from

the square as shown in figures 21 and 22, adjustments

are needed.

 Loosen the bevel lock knob.

COMBINATION

SQUARE

BEVEL

LOCK

KNOB

MITER

FENCE

PARTIAL

SLIDING

MITER

FENCE

SCREW

INDICATOR

SCREW

MITER

SCALE

INDICATOR

Fig. 19

MITER

TABLE

BLADE

18 – English

ASSEMBLY

 Adjust positive stop adjustment screw to bring saw

blade into alignment with the square. See Positive Stop

Adjustment in the Adjustments section.

 Retighten bevel lock knob. Recheck blade-to-table

alignment.

MITER

TABLE

BEVEL

LOCK

KNOB

MITER

FENCE

VIEW OF BLADE NOT SQUARE WITH MITER TABLE,

ADJUSTMENTS ARE REQUIRED

Fig. 22

Fig. 21

VIEW OF BLADE NOT SQUARE WITH MITER TABLE,

ADJUSTMENTS ARE REQUIRED

NOTE: The above procedure can be used to check blade

squareness of the saw blade to the miter table at both 0

°

and 45

°

angles.

The saw has two scale indicators, one on the bevel scale and

one on the miter scale. After squaring adjustments have been

made, it may be necessary to loosen the indicator screws

and reset them to zero. See figures 18 - 19.

OPERATION

WARNING:

Do not allow familiarity with tools to make you careless.

Remember that a careless fraction of a second is

sufficient to inflict serious injury.

WARNING:

Always wear eye protection with side shields marked to

comply with ANSI Z87.1. Failure to do so could result in

objects being thrown into your eyes, resulting in possible

serious injury.

WARNING:

Do not use any attachments or accessories not

recommended by the manufacturer of this tool. The use

of attachments or accessories not recommended can

result in serious personal injury.

APPLICATIONS

This product has been designed only for the purposes listed

below:

 Cross cutting wood and plastic (do not cut metals,

ceramics, or masonry products)

 Cross cutting miters, joints, etc. for picture frames

moldings, door casings, and fine joinery

 Bevel cutting and compound cutting of lumber and

moldings

BEVEL

LOCK

KNOB

MITER

FENCE

MITER

TABLE

COMBINATION

SQUARE

COMBINATION

SQUARE

BLADE

19 – English

OPERATION

Fig. 23

BATTERY

PACK

LATCH

DEPRESS LATCHES TO

RELEASE BATTERY PACK

WARNING:

Always remove battery pack from your tool when you

are assembling parts, making adjustments, cleaning,

transporting, or when not in use. Removing battery pack

will prevent accidental starting that could cause serious

personal injury.

 Locate and depress the latches on each side of the battery

pack to release the battery pack from the saw.

 Remove the battery pack.

For complete charging instructions, refer to the Operator’s

Manuals for your battery pack and charger.

CUTTING WITH YOUR COMPOUND

MITER SAW

WARNING:

When using a work clamp or C-clamp to secure your

workpiece, clamp workpiece on one side of the blade

only. The workpiece must remain free on one side of the

blade to prevent the blade from binding in workpiece. The

workpiece binding the blade will cause motor stalling and

kickback. This situation could cause an accident resulting

in possible serious personal injury.

WARNING:

NEVER move the workpiece or make adjustment to any

cutting angle while the saw is running and the blade is

rotating. Any slip can result in contact with the blade

causing serious personal injury.

NOTE: The blade provided is fine for most wood cutting

operations, but for fine joinery cuts or cutting plastic, use

one of the accessory blades available from the dealer.

WARNING:

Before starting any cutting operation, clamp or bolt the

compound miter saw to a workbench or an approved

workstand. Never operate the miter saw on the floor or

in a crouched position. Failure to heed this warning can

result in serious personal injury.

WARNING:

To avoid serious personal injury, always tighten the miter

lock knob and the bevel lock knob before making a cut.

Failure to do so could result in movement of the control

arm or miter table while making a cut.

WARNING:

To avoid serious personal injury, keep hands outside

the no hands zone, at least 4 in. from the blade. Never

perform any cutting operation freehand (without holding

workpiece against the fence). The blade could grab the

workpiece if it slips or twists.

WARNING:

Do not start your compound miter saw without checking

for interference between the blade and the miter fence.

Damage could result to the blade if it strikes the miter

fence during operation of the saw. Failure to heed this

warning can also result in serious personal injury.

INSTALLING/REMOVING THE BATTERY PACK

See Figure 23.

 Place battery pack in the saw. Align raised rib on battery

pack with groove inside saw.

 Make sure the latches on each side of the battery pack

snap in place and that the battery pack is secured in the

tool before beginning operation.

20 – English

OPERATION

WORK

CLAMP

CROSS CUT

MITER CUT

TO MITER CUT/CROSS CUT

See Figures 24 - 25.

A cross cut is made by cutting across the grain of the

workpiece. A straight cross cut is made with the miter table

set at the 0° position. Miter cross cuts are made with the

miter table set at some angle other than zero.

NOTE: It may be necessary to adjust the sliding miter fence

to ensure proper clearance prior to making the cut.

 Pull out the lock pin and lift saw arm to its full height.

 Loosen the miter lock knob approximately one-half turn

and press the detent release button.

 Rotate the miter table until the pointer aligns with zero

on the miter scale.

NOTE: You can quickly locate 0°, 15°, 22.5°, 31.6°, and 45°

left or right by releasing the detent release button as you

rotate the control arm. The control arm will seat itself in one

of the positive stop notches, located in the miter table base.

 Release the detent release button, then tighten the miter

lock knob to secure the miter table.

 Place the workpiece flat on the miter table with one edge

securely against the fence. If the board is warped, place

the convex side against the fence. If the concave edge

of a board is placed against the fence, the board could

collapse on the blade at the end of the cut, jamming the

blade. See Figures 32 - 33.

 When cutting long pieces of lumber or molding, support

the opposite end of the stock with a roller stand or with

a work surface level with the saw table. See Figure 30.

 Lower the blade and align the cutting line on the workpiece

with the edge of saw blade.

 Grasp the stock firmly with one hand and secure it against

the fence. Use the work clamp, C-clamp, or other suitable

clamp to secure the workpiece when possible.

 Before turning on the saw, perform a dry run of the cutting

operation just to make sure that no problems will occur

when the cut is made.

 Grasp the saw handle firmly. Depress the trigger lockout

lever and squeeze the switch trigger. Allow several sec-

onds for the blade to reach maximum speed.

 Slowly lower the blade into and through the workpiece.

 Release the switch trigger and allow the blade to stop

rotating before raising the blade out of the workpiece and

removing the workpiece from the miter table.

Fig. 24

Fig. 25

WORK

CLAMP

La page est en cours de chargement...

Ryobi P553 Le manuel du propriétaire

Ryobi P553 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents