Genesis GMSDR1015LC Manuel utilisateur

Marque: Genesis

Modèle: GMSDR1015LC

Catégorie: Scies à onglet

Taper: Manuel utilisateur

10” Sliding Compound Miter Saw

Scie à onglets composés coulissante de 254 mm

Sierra ingleteadora compuesta deslizante de 254 mm

GMSDR1015LC

Operator’s Manual

Manuel d’utilisation

Manual del Operario

888-552-8665

TOLL FREE

HELP LINE:

WEBSITE:

www.genesispowertools.com

English

10" Sliding Compound Miter Saw

Operator’s Manual GMSDR1015LC

10" SLIDING COMPOUND MITER SAW

Operator’s Manual

SPECIFICATIONS

• Model#:----------------------------------------------------- GMSDR1015LC

• Rated Power:----------------------------------------------- 120V~/ 60HZ, 15 Amp

• No Load Speed:-------------------------------------------- 4,800 RPM

• Blade Size: ------------------------------------------------- 10” (254 mm)

• Arbor Size: ------------------------------------------------- 5/8”

• Bevel: ------------------------------------------------------ 45° Left

• Miter: ------------------------------------------------------ 45° Left and Right

• Max Cutting Capacity at 0° x 90°:-------------------------- 3” H x 12” W

• Max Cutting Capacity at 45° x 90°: ------------------------- 3” H x 8-1/4” W

• Max Cutting Capacity at 0° x 45°: -------------------------- 1-5/8” H x 12” W

• Max Cutting Capacity at 45° x 45°: ------------------------- 1-5/8” H x 8-1/4” W

• Net Weight: ------------------------------------------------- 34 lbs

• Laser: -- Class II Laser, Wave Length: 650 nm, Max Output <1.0 mw

Includes: Saw, 60T Carbide Tipped Blade, Hold Down Clamp, Dust Bag, 2-Extension Wings, Rear

Support Foot, 2-AAA Batteries for Laser and Blade Wrench

WARNING: To reduce the risk of injury, user must read and understand this

operator’s manual before operating this tool. Save this Manual for future reference.

Toll-Free Help Line: 1-888-552-8665

WARNING: The Operation of any power tool can result in foreign objects

being thrown into your eyes, which can result in severe eye damage. Before beginning

tool operation, always wear safety goggles or safety glasses with side shields and a

full face shield when needed. We recommend Wide Vision Safety Mask for use over

eyeglasses or standard safety glasses with side shields. Always wear eye protection

which is marked to comply with ANSI Z87.1.

Look for this symbol to point out important safety

precautions. It means attention!!! Your safety is involved.

GENERAL SAFETY RULES

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and

other construction activities contains chemicals known to cause cancer, birth defects or

other reproductive harm. Some examples of these chemicals are

• Lead from lead-based paints.

• Crystalline silica from bricks and cement and other masonry products.

• Arsenic and chromium from chemically treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your

exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as

those dust masks that are specially designed to ﬁlter out microscopic particles

WEAR YOUR

FORESIGHT IS BETTER

THAN NO SIGHT

SAFETY GLASSES

English

WARNING: Read and understand all warnings, cautions and operating

instructions before using this equipment. Failure to follow all instructions listed below

may result in electric shock, ﬁre and/or serious personal injury.

SAVE THESE INSTRUCTIONS

WORK AREA SAFETY

• Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.

•

Do not operate power tools in explosive atmospheres, such as in the presence of

ﬂammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.

•

Keep bystanders, children, and visitors away while operating a power tool.

Distractions can cause you to lose control.

ELECTRICAL SAFETY

• Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any

adaptor plugs in any earthed (grounded) power tools. Double insulated tools are equipped with a polarized

plug (one blade is wider than the other). This plug will ﬁt in a polarized outlet only one way. If the plug does not

ﬁt fully in the outlet, reverse the plug. If it still does not ﬁt, contact a qualiﬁed electrician to install a polarized

outlet. Do not change the plug in any way. Double insulation eliminates the need for the three wire grounded

power cord and grounded power supply system.

•

Do not expose power tools to rain or wet conditions. Water entering a power tool will

increase the risk of electric shock.

•

Avoid body contact with earthed or grounded surfaces such as pipes,

radiators, ranges and refrigerators

. There is an increased risk of electric shock if your body is

grounded.

•

Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving parts. Damaged cords increase the risk of electric shock.

•

When operating a power tool outside, use an extension cord suitable for

outdoor use

. These cords are rated for outdoor use and reduce the risk of electric shock.

•

Do not use AC only rated tools with a DC power supply. While the tool may appear to

work. The electrical components of the AC rated tool are likely to fail and rate a hazard to the operator.

PERSONAL SAFETY

• Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use

tool while tired or under the inﬂuence of drugs, alcohol, or medication. A moment of inattention while operating

power tools may result in serious personal injury.

•

Use safety equipment. Always wear eye protection. Safety equipment such as dust mask, non-skid

safety shoes, hard hat, or hearing protection for appropriate conditions will reduce personal injuries.

•

Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from

moving parts. Loose clothes, jewelry or long hair can be caught in moving parts. Air vents may cover moving

parts and should be avoided.

•

Avoid accidental starting. Ensure the switch is in the off position before plugging in. Carrying power

tool with your ﬁnger on the switch or plugging in power tools that have the switch on invites accidents.

•

Remove any adjusting keys or wrenches before turning the power tool on. A

wrench or key that is left attached to a rotating part of the tool may result in personal injury.

•

Do not overreach. Maintain proper footing and balance at all times. Loss of balance can cause an injury

in an unexpected situation.

•

If devices are provided for connection of dust extraction and collection

facilities, ensure these are connected and properly used

. Use of these devices can

reduce dust related hazards.

•

Do not use a ladder or unstable support. Stable footing on a solid surface enables better

control

of the tool in unexpected situations.

English

10" Sliding Compound Miter Saw

Operator’s Manual GMSDR1015LC

• Keep tool handles dry, clean and free from oil and grease. Slippery handles cannot

safely control the tool.

TOOL USE AND CARE

• Secure the workpiece. Use clamp or other practical way to hold the workpiece to a stable platform.

Holding the workpiece by hand or against your body is unstable and may lead to loss of control.

•

Do not force the power tool. The tool will perform the job better and safer at the feed rate for

which it is designed. Forcing the tool could possibly damage the tool and may result in personal injury.

•

Use the correct power tool for the job. Don’t force the tool or attachment to do a job for

which it is not designed.

•

Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled

with the switch is dangerous and must be repaired or replaced by an authorized service center.

•

Turn power tool off, and disconnect the plug from the power source and/or battery pack

from the power tool before making any adjustments, changing the accessories, or storing the tools. Such

preventive safety measures reduce the risk of an accidental start up which may cause personal injury.

•

Store idle tool out of reach of children and other inexperienced persons. It is

dangerous in the hand of untrained users.

•

Maintain power tools with care. Check for proper alignment and binding of moving parts,

component breaks, and any other conditions that may affect the tool’s operation. A guard or any other part

that is damaged must be properly repaired or replaced by an authorized service center to avoid risk of

personal injury.

•

Use recommended accessories. Using accessories and attachments not recommended by the

manufacturer or intended for use on this type tool may cause damage to the tool or result in personal injury to

the user. Consult the operator’s manual for recommended accessories.

•

Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

•

Feed the workpiece in the correct direction and speed. Feed the workpiece into a blade,

cutter, or abrasive surface against the direction of the cutting tool’s direction of rotation only. Incorrectly feeding

the workpiece in the same direction may cause the workpiece to be thrown out at high speed.

•

Never leave the tool running unattended, turn the power off. Do not leave the tool

until it comes to a complete stop.

•

Never start the power tool when any rotating component is in contact with

the workpiece.

WARNING: USE OF THIS TOOL CAN GENERATE AND DISBURSE DUST OR

OTHER AIRBORNE PARTICLES, INCLUDING WOOD DUST, CRYSTALLINE SILICA DUST

AND ASBESTOS. Direct particles away from face and body. Always operate tool in a

well-ventilated area and provide for proper dust removal. Use dust collection system

wherever possible. Exposure to the dust may cause serious and permanent respiratory

or other injury, including silicosis (a serious lung disease), cancer, and death. Avoid

breathing the dust, and avoid prolonged contact with the dust. Allowing dust to get into

your mouth or eyes, or lay on your skin may promote absorption of harmful material.

Always use properly ﬁtting NIOSH/OSHA approved respiratory protection appropriate for

dust exposure, and wash exposed areas with soap and water.

SERVICE

• Have your power tool serviced by a qualiﬁed repair person using only

identical replacement parts. This will ensure that the safety of the power tool is maintained.

•

Service your power tool periodically. When cleaning a tool, be careful not to disassemble any

portion of the tool since internal wires may be misplaced or pinched.

SAVE THESE INSTRUCTIONS

English

EXTENSION CORDS

Grounded tools require a three wire extension cord. Double insulated tools can use

either a two or three wire extension cord. As the distance from the power supply outlet increases, you must use a

heavier gauge extension cord. Using extension cords with inadequately sized wire causes a serious drop in voltage,

resulting in loss of power and possible tool damage. Refer to the table shown below to determine the required

minimum wire size.

The smaller the gauge number of the wire, the greater the capacity of the cord. For example: a 14-gauge cord

can carry a higher current than a 16-gauge cord. When using more than one extension cord to make up the total

length, be sure each cord contains at least the minimum wire size required. If you are using one extension cord for

more than one tool, add the nameplate amperes and use the sum to determine the required minimum wire size.

Guidelines for Using Extension Cords

• If you are using an extension cord outdoors, be sure it is marked with the sufﬁx “W-A” (“W” in Canada) to

indicate that it is acceptable for outdoor use.

• Be sure your extension cord is properly wired and in good electrical condition. Always replace a damaged

extension cord or have it repaired by a qualiﬁed person before using it.

• Protect your extension cords from sharp objects, excessive heat, and damp or wet areas.

SPECIFIC SAFETY RULES FOR MITER SAWS

WARNING: DO NOT LET COMFORT OR FAMILIARITY WITH PRODUCT (GAINED

FROM REPEATED USE) REPLACE STRICT ADHERENCE TO PRODUCT SAFETY RULES. If

you use this tool unsafely or incorrectly, you can suffer serious personal injury!

•

Do not operate this miter saw until it is assembled and installed according to the instructions.

•

If you are not thoroughly familiar with the operation of miter saws, seek

guidance from your supervisor, instructor, or other qualiﬁed person.

•

Mount the tool securely to a stable supporting surface prior to operation.

Ideally, ﬁrmly clamp or bolt your miter saw to a workbench, table, or tool stand at approximately hip height.

•

Use the guards whenever possible. Check that the guards are correctly positioned, secured,

and working properly.

•

Use only crosscut saw blades. Use only zero-degree or negative hook angles when using

carbide tipped blades.

IMPORTANT: Do not use thin kerf blades or blades with deep gullets. These can

easily deﬂect and contact the guard or miter saw table.

•

Use only blades that are the correct size and type speciﬁed for this tool.

• Be sure to use a sharp blade that runs freely and is free of vibration.

•

Inspect blades for cracks or other damage prior to operation. Replace a cracked or

damaged blade immediately.

•

Clean the blade and blade ﬂange washers prior to operation. Again, check for any

damage and tighten the arbor nut securely.

•

Use only the blade ﬂanges speciﬁed for this tool.

•

Keep your hands out of the path of the saw blade. If the workpiece being cut causes

your hands to be within 7-1/4” of the saw blade, the workpiece should be clamped in place before making

the cut.

Recommended Minimum Wire Gauge for Extension Cords (120 Volt)

Nameplate

Amperes

(At Full Load)

Extension Cord Length

25 Feet 50 Feet 75 Feet 100 Feet 150 Feet 200 Feet

0–2.0 18 18 18 18 16 16

2.1–3.4 18 18 18 16 14 14

3.5–5.0 18 18 16 14 12 12

5.1–7.0 18 16 14 12 12 10

7.1–12.0 18 14 12 10 8 8

12.1–16.0 14 12 10 10 8 6

16.1–20.0 12 10 8 8 6 6

English

10" Sliding Compound Miter Saw

Operator’s Manual GMSDR1015LC

• Keep the motor air slots clean and free of chips, dust, or other obstructions which may

impair the ﬂow of cooling air to the motor.

•

Make sure all the saw’s adjustment handles are tight before cutting, even if the table

is positioned in one of positive stops. Do not forget to tighten the rear mounted bevel adjustment handle.

•

Never apply lubricants to the blade when it is running.

•

Never use saw blades rated for operation at less than 5,000 rpm.

•

Never start the tool with the workpiece against the blade.

•

Allow the motor to attain full speed prior to starting the cut.

•

Always keep the blade guards in place and use at all times.

•

Never reach around or behind the saw blade.

•

Never lock the switch in the “ON” position.

•

Never attempt to recut small pieces.

• Never cut ferrous metals or masonry. This miter saw is designed to cut wood and wood-

like products.

• Do not perform free-hand cutting operations. Hold the work ﬁrmly against the fence

and table. Use clamps to hold the work when possible.

• Long or wide workpieces should be properly supported.

• IMPORTANT: After completing the cut, release the power switch and allow the blade to

come to a complete stop before returning the saw to a raised position.

•

Turn off the saw and allow the blade to completely stop before cleaning the blade

area or removing debris and off-cuts in the path of the blade. Coasting blades are dangerous.

•

Turn off the saw and allow the blade to completely stop before removing or un-

securing the workpiece, changing the workpiece angle, or changing the angle of the blade.

•

Never perform layout, assembly or set-up work on the saw table or work area while the machine

is running.

•

Turn the machine “off” and disconnect the machine from the power source before

installing or removing accessories, before adjusting or changing set-ups, or when making repairs.

•

Disconnect the machine from the power source and clean the work area before leaving the

machine.

•

If any part of your miter saw is missing, damaged, or fails in any way, or any

electrical component fails to perform properly, shut off the switch and remove the plug from the power

source. Replace missing, damaged, or failed parts before resuming operation.

WARNING: Read and understand all warnings, cautions and operating

instructions before using this equipment. Failure to follow all instructions listed below

may result in electric shock, ﬁre and/or serious personal injury.

SAVE THESE INSTRUCTIONS

English

GLOSSARY OF WOODWORKING TERMS

Workpiece-- A piece of wood on which the cutting operation is being performed.

Anti-Kickback Pawls-- Device which, when properly installed and maintained, is designed to stop the

workpiece from being kicked back toward the operator during the operation.

Arbor-- The shaft on which a cutting tool is mounted.

Bevel Cut-- A cutting operation made with an angled blade.

Compound Miter Cut -- A single cut made with both a miter angle and a bevel angle.

Cross Cut -- A cut or shaping operation made across the workpiece.

Dado -- A non-through cut which produces a square sided notch or trough in the workpiece.

Feather board -- A device used to help control the workpiece by guiding it securely against the table or

fence during any rip cut operation.

Freehand -- Performing a cut without using a fence, miter gauge, ﬁxture, hold down clamp, or other

proper device to keep the workpiece from twisting during the cut – not recommended.

Gum -- A sticky, sap-based residue from wood products.

Heel -- Misalignment of the blade. Heel can cause binding, kickback, excessive force burning the workpiece

or splintering

Kerf -- The amount of material removed by the blade in a through cut, or the slot produced by the blade in

non-through or partial cut.

Kickback -- An uncontrolled grabbing or throwing of the workpiece back toward the front of the saw,

associated with the workpiece closing the kerf and pinching the blade or otherwise placing tension on the

blade.

Leading End -- The end of the workpiece, which during a rip type operation is pushed into the cutting

tool ﬁrst.

Miter Cut -- A cutting operation made with the wood at any angle other than 90 degree to the blade.

Molding -- A cut which produces a special shape in the workpiece, used for joining or decoration.

Non-Through Cut -- Any cutting operation where the blade does not extend completely through the

thickness of the workpiece

Push Block -- A device used to feed the workpiece through the saw during narrow rip type operations

where a push stick can not be used. It also helps keep the operator's hands well away from the blade.

Push Stick -- A device used to feed the workpiece through the saw to help keep the operator's hands well

away from the blade.

Rabbet -- A notch in the edge of the workpiece.

Resin -- A sticky, sap-based substance that has hardened.

Rip Cut -- A cutting or shaping operation made along the length of the workpiece.

Rip Fence -- Adjustable guide used in ripping cuts to keep the workpiece parallel to the saw blade.

RPM -- Revolutions per Minute. The number of turns completed by a spinning object in one minute

Saw Blade Path -- The area over, under, behind, or in front of the blade. As it applies to the workpiece,

that area which will be, or has been, cut by the blade.

English

10" Sliding Compound Miter Saw

Operator’s Manual GMSDR1015LC

KNOWING YOUR MITER SAW

1. Handle

2. Lock-Off Switch

3. Trigger Switch

4. Motor

5. Carrying Handle

6. Upper Blade Guard

7. Lower Blade Guard

8. Rear Carrying handle

9. Dust Bag

10. Sliding Rails

11. Slide Lock Knob

12. Fence

13. Hold Down Work Clamp

14. Table Extension

15. Extension Lock Knob

16. Base

17. Miter Table

18. Miter Angle Pointer

19. Throat Plate

20. Detent Lever

21. Bevel Scale

22. Miter Lock Handle

23. Laser

24. Saw Head Lock Pin

25. Bevel Lock Handle

26. Dust Port

27. Blade

28. Spindle Lock Button

29. Miter Scale

30. Laser Battery Compartment

31. Rear Support Foot

FIG 1

English

UNPACKING AND CONTENTS

IMPORTANT: Due to modern mass production techniques, it is unlikely the tool is

faulty or that a part is missing. If you ﬁnd anything wrong, do not operate the tool until

the parts have been replaced or the fault has been rectiﬁed. Failure to do so could result

in serious personal injury.

CONTENTS IN PACKAGE

Description Q'ty Description Q'ty

UNPACKING

1. Remove all loose parts from the carton.

2. Remove the packing materials from around the saw.

3. Using the carrying handles (5 & 8-FIG 1) carefully lift the saw from the carton and place it on a level work

surface.

4. The saw has been shipped with the saw head locked in the down position. To release the saw head push down

on the top of the saw head, pull the lock pin (24-FIG 1) outward, slowly raise the saw head.

ASSEMBLY AND ADJUSTMENTS

WARNING: DO NOT connect your compound miter saw to the power source

until the machine is completely assembled, all necessary adjustments made, and you

have read and understand the entire operator’s manual.

WARNING: Be sure that the tool is switched off and unplugged from the power

source before performing any work on the tool. Failure to unplug the saw may result in

accidental start-up, causing possible serious personal injury.

Your saw comes from the factory fully adjusted and requires only minor assembly to prepare the miter saw for

operation.

MOUNTING THE SAW

WARNING: Always make sure the miter saw is securely mounted to a workbench

or an approved miter stand. Failure to heed this warning can result in serious personal

injury.

The compound miter saw should be permanently mounted to a ﬁrm supporting surface such as workbench. Four

bolt holes have been provided in the saw base for this purpose. Each of the four mounting holes should be bolted

securely using 3/8" machine bolts, lock washers and hex nuts (not included). After securely mounting the saw,

carefully check the workbench to make sure that no movement can occur during use. If any tipping, sliding, or

walking is noted, secure the workbench to the ﬂoor before operation.

DUST PORT & DUST BAG (FIG 2)

The saw has a 1-1/2" sawdust port (1) at the rear of upper blade

guard. A dust collection system can be attached to this port to help

remove sawdust from the work area.

A dust bag (2) is provided for use with your miter saw. It can

be installed over the sawdust port. Squeeze the two metal clips

to open the mouth of the bag and slide onto the sawdust port.

Release pressure on the clips and the metal ring at the bag’s

opening should lock in the grooves of the sawdust port. To remove

the dust bag for emptying, simply reverse the above procedure.

The dust bag should be checked often and if more than half full, remove the bag by simply reversing the installation

procedure. Dispose of the accumulated saw dust in the dust bag and then reinstall the dust bag before resuming

operation of the miter saw.

FIG 2

Saw Assembly 1

Dust Bag 1

Hold Down Clamp 1

Rear Support Foot 1

Wrench 1

AAA batteries 2

Operator's Manual 1

English

10" Sliding Compound Miter Saw

Operator’s Manual GMSDR1015LC

TABLE EXTENSIONS (FIG 3)

Your saw comes with two table extensions (1). They can be installed

in either the left or the right side of the saw base.

To Install the Table Extensions

1. Loosen the extension lock knob (2).

2. Insert the ends of the table extension into the holes (3) in

the side of the base and adjust the extensions to the desired

length.

3. Secure the extensions by tightening the extension lock knob.

The extension comes with a stop block (4) installed on the farther

side of the extension. The stop block is useful as a stop for making

repetitive cuts to the same length.

To Use the Stop Block

1. Tilt the stop block up as shown on FIG 3.

2. Adjust the extension to desired cutting length.

3. Make a test cut in scrap material and measure the length of

the workpiece.

4. Make any necessary adjustments.

REAR SUPPORT FOOT (FIG 4)

A rear support foot (1) is provided to improve the stability of the

saw. Insert it to two holes on the back of the base. Tighten the

locking screw (2) located on the bottom of the base to secure it.

WORK CLAMP ASSEMBLY (FIG 5)

WARNING: In some operations, the work

clamp assembly may interfere with the operation of

the blade guard assembly. Always make sure there

is no interference with the blade guard prior to beginning any cutting operation to reduce

the risk of serious personal injury.

This miter saw is equipped with a Hold down Work Clamp (1). The work clamp can be positioned in the provided

mounting holes in the base behind the miter fence to the right and left of the cutting head. Insert the clamp

column (3) into the mounting hole (2). Secure it by tightening the screw (6). Use the clamp lock screw (4) to

quickly secure the clamp in position. Use the clamp tightening screw (5) to secure workpiece against the miter

table as needed, especially small workpiece.

The work clamp provides greater control by clamping the workpiece to the fence or the saw table. It also

prevents the workpiece from creeping toward the saw blade. This is very helpful when cutting compound miters.

NOTE: Depending on the cutting operation and the size of the workpiece, it may be necessary to use a

C-clamp instead of the hold down work clamp to secure the workpiece prior to making the cut.

CHANGING THE SAW BLADE (FIG 6, 7, 8, 9)

WARNING: Be sure that the tool is switched off and unplugged from the power

source before performing any work on the tool.

WARNING: Use only 10 inch diameter saw blades and are rated for speeds

equal to or greater then the nameplate rated RPM of this miter saw.

WARNING: Use only blades designed for cross-cutting operations.

WARNING: Do not use thin kerf blades with deep gullets which may deﬂect and

contact the blade guards or produce poor quality cuts in the workpiece.

FIG 3

FIG 5

FIG 4

English

To Change the Blade

1. Unplug the saw.

2. Lift up the lower blade guard (3). Loosen the Phillips screw

(1) on the blade bolt cover (2).

3. Lift up the blade bolt cover (2) to expose the blade bolt.

4. Depress the spindle lock (7) and rotate the blade until the

spindle locks.

5. Using the 13 mm wrench (4) provided, loosen the blade bolt

(5) by turning it clockwise. Remove the blade bolt.

6. Remove the outer blade ﬂange (6).

7. Remove the old blade from the saw.

NOTE: A blade washer may be use for the blade with arbor

hole bigger than 5/8 inch.

8. Mount the new blade carefully onto the spindle, being sure

that the directional arrow on the blade surface matches the

arrow on the upper blade guard.

9. Replace the outer blade ﬂange and the blade bolt.

10. Depress and hold down the spindle lock (7) while tightening

the blade locking bolt securely with the 13 mm wrench in a

counterclockwise direction.

11. Lower the blade bolt cover to its original position.

12. Retighten the Phillips screw securing the blade bolt cover.

Lower the lower blade guard.

13. Be sure the spindle lock has released and blade rotates freely

before plugging in the tool and making a cut.

LASER GUIDE (FIG 10)

WARNING: Laser light – do not stare

into the beam, aperture, or into a reﬂection from a

mirror-like surface.

WARNING: Avoid exposure – laser light

is emitted from the rear guard aperture. Use

of controls or adjustments, or performance of

procedures other than those speciﬁed herein may

result in hazardous laser light exposure.

WARNING: DO not disassemble the laser

module.

WARNING: USE of controls or adjustments

or performance of procedures other than those

speciﬁed herein may result in hazardous radiation

exposure.

Your miter saw is equipped with a battery powered laser (1). The

Laser Battery Compartment (30-FIG 1) is located at the right side

of the saw under the motor. Install two included AAA batteries into

battery compartment before using the laser. The Laser ON/OFF

switch is located on the laser battery compartment.

The laser alignment was made at the factory and is set for the

center of the blade or draw line. Adjustment may be required prior

to initial use due to the effects of shipping and handling. You also

have the ability to adjust the line projected by the laser to your liking. You may wish for the laser to be to right or

left of the blade, or straight on a drawn cut line. Where you ultimately decide to align the laser in relation to the

saw blade’s cutting path will determine how you align the cut line.

On each side of the laser are two Phillips head screws (2) which, when loosened, allow movement to the left and

right. The screw (3) on the laser’s stem area also allows left/right movement, but more importantly will affect

the straightness of the laser line. Beware that small adjustments can yield dramatic changes in the laser’s path.

FIG 6

FIG 7

FIG 8

FIG 9

FIG 10

English

10" Sliding Compound Miter Saw

Operator’s Manual GMSDR1015LC

With patience and practice you’ll be able to place the laser line in the ideal position for your style of blade to cut

line alignment.

DEPTH OF CUT ADJUSTMENT (FIG 11)

WARNING: Be sure the machine is unplugged from the power source.

Accidental saw start-up could result in serious personal injury.

NOTE: Your miter saw should come adjusted properly for depth of cut while using the factory-installed blade

for normal operation.

The downward travel or depth of cut, of the saw blade can be controlled to prevent contact with the metal

surfaces of the miter saw, to insure the blade completely cuts through the workpiece, and permit depth of cut

settings for special operations.

NOTE: This is factory set and usually does not require adjusting.

(This saw may not come with the necessary tools for the following

procedure.)

To Achieve the Maximum Cutting Depth, tilt the Cutting

Depth Stop Plate (2) to a upward position. It disables the cutting

depth adjusting control and maximizes the cutting depth for

regular cutting-through operations.

To Adjust Cutting Depth

NOTE

: This is useful for performing dado cuts or to create lap joints.

1. Locate the Depth Control Assembly (1+2) on the right side of the saw arm.

2. If the saw arm is locked in the down position, release it by pulling the saw arm lock pin out.

3. Tilt the Cutting Depth Stop Plate (2) to the horizontal position. See FIG 11.

4. Turn the Depth Control Knob (1). Clockwise will decrease the amount of travel and depth of cut, counter-

clockwise will increase the amount of travel and depth of cut.

5. Lower the saw arm completely. The Depth Control Knob (1) will contact the Cutting Depth Stop Plate (2).

Check if it is the cutting depth desired. If not, repeat step 4.

You will need to experiment and make several test cuts until you determine the proper depth of cut. We suggest

you practice on scrap wood with the same thickness dimensions before you start cutting your project wood.

SQUARING THE SAW BLADE TO THE FENCE (FIG 12, 13)

WARNING: Be sure that the tool is

switched off and unplugged from the power source

before performing any work on the tool. Failure to

unplug the saw may result in accidental start-up,

causing possible serious personal injury.

1. Unplug the miter saw.

2. Put the slide in the most backward position. Lock the slide by

tightening the slide locking knob securely.

3. Loosen the miter lock handle. Rotate the miter table and move

0° miter stop position.

(NOTE: Check if the red miter pointer (1) points to 0° on

the miter scale. If not, loosen the miter pointer screw, adjust

the pointer to point accurately to 0° scale mark, tighten the

pointer screw.)

4. Tighten the miter lock handle securely.

5. Pull the saw head down completely and lock the blade and

arm in the down position.

6. Lay a small framing square (3) or tri-square on the miter table.

Place one leg of the square against the fence (2) and slide the other leg of the square against a ﬂat part of the

saw blade. (Be sure the square contacts the ﬂat part of the saw blade and not the blade teeth.)

FIG 13

FIG 12

FIG 11

English

7. Check that the edge of the square and the saw blade are parallel along the entire length of the square’s edge.

8. If the front or back portion of the blade angles away from the square's edge, adjusting the fence is necessary.

9. Using the 5 mm Allen wrench, loosen the four hex bolts (4) that secure the fence to the saw’s stationary table.

10. While holding one leg of the square against the fence, slowly move the fence (2) to the left or right until the

saw blade is parallel with the square's other leg.

11. Carefully tighten the four hex bolts and recheck the blade alignment as in steps 6 and 7.

0° AND 45° BEVEL STOP ADJUSTMENTS

(FIG 14, 15 )

NOTE:

This is factory set and usually does not require adjusting.

(This saw may not come with the necessary tools for the following

procedure.)

WARNING: Be sure that the tool is

switched off and unplugged from the power source

before performing any work on the tool. Failure to

unplug the saw may result in accidental start-up,

causing possible serious personal injury.

To Adjust the 0° Bevel Stop

1. Unplug the miter saw.

2. Put the slide in the most backward position. Lock the slide by

tightening the slide locking knob securely.

3. Align the miter table to 0° and lock the saw head down in the

transport position.

4. Loosen the bevel lock handle (3) at the rear of the saw, set the

saw arm at 0° bevel stop (blade 90° to the miter table).

5. Place a combination square on the miter table and the ﬂat

part of the saw blade (making sure the square is not touching

any blade teeth).

6. Slowly rotate the blade by hand, checking the square’s alignment with the blade at several points. The edge

of the square and blade should be parallel; however, if the top or bottom of the blade angles away from the

square’s edge, an adjustment is needed.

7. Locate the 0° bevel stop adjustment bolt (1) on the lower right side of the bevel knuckle.

8. Use 5 mm Allen wrench to adjust the 0° bevel stop adjustment bolt and so that the blade is in alignment with

the square.

9. If necessary, loosen the bevel angle indicator pointer and adjust it to point accurately to the 0° line, then

retighten the screw.

To Adjust the 45° LEFT Bevel Stop. Follow the directions for adjusting the 0° bevel stop, except position the

saw arm at a 45° left bevel stop. The 45° left bevel stop adjustment bolt (2) is located on the upper right side of

the bevel knuckle.

OPERATION

WARNING: Always be sure the miter saw is disconnected from the power source

before making any adjustments or setting up prior to cutting. Failure to disconnect or

unplug the machine may cause accidental starting, resulting in serious personal injury.

WARNING: Always wear safety goggles or safety glasses with side shields

when operating tools. Failure to do so could result in objects being thrown into your eyes

resulting in possible serious injury.

TRANSPORTING THE SAW

1. Always make sure the saw head is down and locked.

2. Make sure the miter table is locked, Bevel is locked at 0° position.

3. Make sure the sliding saw head is in the most backwards position and locked.

4. Only lift the saw by the carrying handle or outer castings.

FIG 14

FIG 15

English

10" Sliding Compound Miter Saw

Operator’s Manual GMSDR1015LC

WARNING: Always transport the miter saw in the locked down position,

carrying the saw by carrying handle on the cutting arm. DO NOT lift or carry the miter saw

using the trigger handle, doing so may cause misalignment of miter and bevel settings.

LOCKING AND UNLOCKING THE CUTTING HEAD (FIG 16)

When storing or transporting the miter saw, the cutting head should be locked in the down position.

To Lock Down the Cutting Head

1. Lower the cutting head completely with the cutting depth stop

plate (2) in the upward position.

2. Push the locking pin (1) inwards to lock the cutting head.

To Unlock the Cutting Head

1. Press down lightly on the cutting head.

2. Pull the lock pin (1) outwards to unlock the cutting head.

3. Slowly raise the cutting head to the work position.

STARTING AND STOPPING THE MITER

SAW (FIG 17)

NOTE

: The saw is equipped with a Lock-Off Switch (2) for extra

safety.

To start the miter saw, ﬁrmly grasp the saw's top handle. Use

your thumb to press the Lock-Off switch (2), then depress the

trigger switch (1).

To stop the miter saw, completely release the trigger switch.

WARNING: After completing a cut, release

the trigger switch to activate the electric blade

brake. Keep the cutting head down until the blade

comes to a complete stop before raising the cutting

head to the upward or starting position. A rotating

saw blade can be dangerous.

WARNING: The torque resulting from

electric blade brake activation may loosen the arbor

bolt. Occasionally check the arbor bolt and tighten

if necessary.

TABLE HAZARD AREA (FIG 18)

On each side of the rotating miter table, there is a “hands” warning symbol that is cast into the table. The area

between the two “hand” symbols is designated as a “Hazard Zone” and the miter saw operator should never place

their hands inside this area while the miter saw is running.

WARNING: Keep your hands outside the “Hazard Zone” and out of the path

of the saw blade. Use the supplied work clamp or other clamping means to secure the

workpiece in place before making a cut with the miter saw.

ROTATING THE MITER TABLE (FIG 19)

This miter saw will accurately cut any angle from the straight 90°

cut to 45° left and 45° right.

To Rotate the Miter Table, loosen

the Miter Lock Handle (1) one or two turns counterclockwise, Use

your index ﬁnger to pull up the detente lever (2) to release, and

then rotate the miter table to the desired angle using the Miter Lock

Handle (1). When the desired angle is reached, turn the Miter Lock

Handle (1) clockwise to lock the miter table in place.

NOTE: This miter saw comes with 9 positive stops: 0° for 90° cutting, left-15°, 22.5° , 30°, 45°, right-15°,

22.5°, 30°, 45° for quick setting of common miter cutting angles.

FIG 18

FIG 17

FIG 19

FIG 16

English

CAUTION: Always tighten the miter lock handle to secure the miter table in position

before cutting with the miter saw.

POINTER AND SCALE (FIG 19)

An arrow shaped pointer (3) is located at the front end of the miter table. Each line on the miter scale (4) represents

1°. When the miter table is rotated, the pointer is moved from one line to the next along the miter scale, changing

the angle of cut by one degree.

TILTING THE CUTTING HEAD FOR BEVEL

CUTTING (FIG 20)

Your compound miter saw is equipped with a cutting head that can

be tilted to cut any bevel angle from a 90° straight vertical cut to

a 45° left bevel angle cut.

To bevel the cutting head, loosen the bevel lock handle (1) at the

rear of the miter saw, tilt the cutting arm left to the desired angle,

and then tighten the lock handle.

Each line on the bevel scale (3) represents one degree of

movement. The angle setting is indicated by a stationary red

pointer (2) and the bevel angle position of the cutting arm is

determined by the position of the red pointer to a line on the bevel

scale.

Positive stops are provided at 0°, 45° LEFT for quick adjustments.

LOCKING AND UNLOCKING THE SLIDING

RAIL (FIG 21)

Turning the Sliding Rail Lock Knob (1) clockwise will lock the

rail (2) and keep it from traveling forward or backward. Turning

the lock knob counterclockwise will loosen the sliding rail lock,

permitting travel of the saw head and the rail system.

CUTTING WITH A SLIDING MITER SAW

(FIG 22)

The sliding miter saw has much greater cutting capacities than a

conventional miter saw. It is also used a little differently. The FIG

22 shows the proper way to cut using the sliding rail.

Position "a" shows the saw head in the back position. If cutting small, narrow stock, the user needs only to push

down on the cutting head with the saw running to cut the piece.

Position "b" now shows the saw head in the most forward position. This is the starting position for cutting wide

stock up to 12".

With the saw running and the blade at full speed, Push the saw head down into the material slowly and steadily

as shown in position "c"

Once the saw has cut through the initial thickness of the material, steadily push the saw head away from you

while the saw is still cutting to complete the cut as show in position "d".

APPLICATION

TYPICAL COMPOUND MITER SAW OPERATIONS

WARNING: Always be sure the miter saw is disconnected from the power source

before making any adjustments or during set-up prior to cutting. Failure to disconnect or

unplug the machine may cause accidental starting, resulting in serious personal injury.

WARNING: Be sure the miter saw is securely bolted down or clamped to a

workbench or appropriate work surface before performing any cutting operations. Failure

to do so may result in loss of machine control and/or result in personal injury.

FIG 21

FIG 22

FIG 20

English

10" Sliding Compound Miter Saw

Operator’s Manual GMSDR1015LC

WARNING: If securely holding the workpiece causes your hand to be in the

machine’s “Hazard Zone”, clamp the workpiece in place and move your hand(s) to a safe

position before making the cut.

Regardless of the type of cut being performed with your compound miter saw, the following basic set-up steps are

used, unless speciﬁed otherwise.

1. Check and conﬁrm the cutting arm (bevel position) and the rotating table (miter position) are at the correct

settings and the related adjustment handles are ﬁrmly locked in place.

2. Mark the position of desired cut onto the workpiece surface to ensure proper blade and laser alignment.

3. Place the workpiece on the saw table, align the blade and/or laser light with the cut line, then position it ﬁrmly

against the fence and hold or clamp it ﬁrmly in place. If using a hand to hold the workpiece in place, be sure it

is outside the “Hazard Zone”. Never attempt freehand cutting or cutting a workpiece not ﬁrmly held against the

fence or table!

4. Turn on the saw, allowing the blade to reach full speed. Lower the cutting head slowly into the workpiece and

perform the cut at a steady rate.

5. When the cut is completed, release the trigger switch and allow

the blade to completely stop rotating before raising the blade

and cutting head out of the completed cut.

MITER CROSSCUTTING (FIG 23)

Crosscuts are cuts made across the grain of the workpiece, with

a straight cut being made with the both the blade bevel and miter

table set at 0°. A miter crosscut is made when the miter table is set

at some angle other then 0°.

1. Measure and mark the workpiece with the desired cut line.

Mark the workpiece on each side of the cut line indicating

which side is the scrap or off cut and which the desired ﬁnished

piece is.

2. Unlock the rotating miter table by loosening the miter locking

knob.

3. Use the miter handle to rotate the table, left or right, to the

desired cutting angle. Then tighten the miter lock knob.

4. Place the workpiece onto the saw table and against the fence.

Turn on the laser light source.

5. Move the workpiece left or right to align the cut line with the

saw blade and laser light. Then secure the workpiece in place,

holding it either by hand for large pieces or via the clamping

device for small pieces.

6. After conﬁrming the saw settings and that the workpiece is

secured, turn on the saw and make the cut.

BEVEL CUTTING (FIG 24)

A bevel cut is made by cutting across the workpiece grain with the blade angled or tilted to the workpiece. When

making a straight bevel cut, the miter table is set at the 0° position and the blade angled and set at a position

between 0° and 45° left.

1. Measure and mark the workpiece with the desired cut line. Mark the workpiece on each side of the cut line

indicating which side is the scrap or off cut and which the desired ﬁnished piece is.

2. Set and lock the rotating miter table in place at 0°.

3. Loosen the bevel locking handle and move the cutting arm left to the desired bevel angle as indicated by the

bevel scale pointer. Tighten the bevel locking handle securely.

4. Place the workpiece onto the saw table and against the fence. Turn on the laser light.

5. Move the workpiece left or right to align the cut line with the saw blade and laser light. Then secure the

workpiece in place, holding it either by hand or via the clamping device.

6. After conﬁrming the saw settings and that the workpiece is secured, turn on the saw and make the cut.

FIG 23

FIG 24

English

COMPOUND MITER CUTTING (FIG 25)

A compound miter is a cut made using both a miter setting

and blade bevel setting at the same time. This type of cut is

commonly used for picture framing, boxes with angled sides,

roof framing cuts, and trim molding.

Compound miter settings are made up of miter and bevel angles

that are interdependent, therefore, desired and accurate cuts can

be difﬁcult to attain. When a miter angle is changed it affects the

bevel angle setting and vice versa. It may take numerous set-ups

and test cuts to realize the desired outcome. When compound

cuts are required in projects, the settings are usually provided,

taken from specialty manuals with pre-calculated settings,

published charts, etc. Also you may refer to Cutting Compound

Miters chart included in this manual.

1. Set the bevel angle and miter angle as described earlier and lock the respective adjustment handles securely.

2. For the initial cuts, use scrap material for making test cuts to conﬁrm that bevel and miter angles are set

correctly.

3. After conﬁrming the bevel and miter settings are correct, make the compound miter cuts as described in the

previous separate sections for bevel and miter cuts.

CUTTING BASE MOLDING

Base molding can be cut using two methods: standing vertically against the fence or horizontally, laying ﬂat on

the miter table. Using the vertical method is limited by the height capacities of your compound miter saw.

Flat or Horizontal Cutting:

1. Lay the base molding’s back onto the miter table with the bottom of the base molding placed against the

fence.

2. Set the miter angle to 0°.

3. Turn on the laser and set the blade’s bevel to the desired angle, such as 45° for one half of 90° corners.

4. Align the cut line on the workpiece with the blade and laser light.

5. Conﬁrm the saw settings, turn on the saw and make the cut as described earlier.

Vertical Cutting:

1. Stand the base molding upwards with the molding back against the fence and molding bottom sitting on the

miter table.

2. Set the bevel angle to 0°.

3. Turn on the laser and set the miter table to the desired angle, such as 45° for one half of 90° corners.

4. Align the cut line on the workpiece with the blade and laser light.

5. Conﬁrm the saw settings, turn on the saw and make the cut as described earlier.

CUTTING CROWN MOLDING

Your compound miter saw is the ideal tool for cutting crown molding, which bridges the wall and ceiling. The most

common style of crown molding used today has a top rear angle of 52° at the ceiling and a bottom rear angle

of 38° where it meets the wall. For an installation with tight ﬁtting corners where the right and left pieces meet,

extremely accurate bevel and miter angle settings are required.

There are two methods for cutting crown molding. 1) Cutting Crown Molding Flat on the Miter Table. 2) Cutting

Crown Molding Vertically Nested against Miter Fence.

Cutting Crown Molding Flat on the Miter Table

Since the most common corners encountered when using

crown molding measure 90° inside and outside, the following

instructions will be for cutting 52°/38° crown molding to ﬁt 90°

corners with the molding laying ﬂat on the saw table.

FIG 25

FIG 26

INSIDE CORNER

OUTSIDE CORNER

52°

38°

CEILING

English

10" Sliding Compound Miter Saw

Operator’s Manual GMSDR1015LC

INSIDE CORNER OUTSIDE CORNER

Left Side,

1. Top edge of molding against fence

2. Miter table set RIGHT to 31.62°

3. Bevel set at 33.85° Left

4. Save LEFT end of cut

Left Side

1. Bottom edge of molding against fence

2. Miter table set LEFT 31.62°

3. Bevel set at 33.85° Left

4. Save RIGHT end of cut

Right Side

1. Bottom edge of molding against fence

2. Miter table set LEFT to 31.62°

3. Bevel set at 33.85° Left

4. Save LEFT end of cut

Right Side

1. Top edge of molding against fence

2. Miter table set RIGHT 31.62°

3. Bevel set at 33.85° Left

4. Save RIGHT end of cut

NOTE: When cutting and installing crown molding keep in mind the bevel and miter angles involved are

extremely accurate while the corners you’ll be working on will rarely measure exactly 90°. Therefore, be prepared

to make numerous practice cuts with scrap molding to help ﬁne tune your saw settings.

For cutting crown molding ﬂat for corners other than 90°, please refer to Crown Molding Miter Angles chart.

Cutting Crown Molding Vertically Nested Against Miter Fence

Always use a crown molding fence when cutting crown molding angled against the fence. Cutting crown molding

angled against the fence does not require any special bevel settings. Small changes in the miter angle can be

made without affecting the bevel angle. When using this method the saw can be quickly and easily adjusted for

corners that are not 90° (square).

When cutting crown molding in this method, the bottom of the molding goes against the fence. Think of the table

of the saw being the ceiling, and the fence as being the wall. Angled “ﬂats” on back of molding must rest squarely

on the fence and base of the saw.

The following instructions are for cutting crown molding for a 90° corner.

INSIDE CORNER OUTSIDE CORNER

Left Side:

1) Miter RIGHT at 45°

2) Save RIGHT End of Cut

Left Side

1) Miter LEFT at 45°

2) Save Right End of Cut

Right Side

1) Miter LEFT at 45°

2) Save LEFT End of Cut

Right Side

1) Miter RIGHT at 45°

2) Save LEFT End of Cut

CUTTING WARPED WORKPIECES

NOTE:

It is recommended that you do not cut warped material.

Sometimes you have no choice but to use a piece of warped material. To cut warped workpieces, make sure it is

positioned on the miter saw table with the convex side against the fence. DO NOT place the concave side of the

workpiece against the miter saw fence; when it is cut it will collapse near the completion of the cut, pinching the

blade.

WARNING: To avoid possible serious personal injury and possible kickback,

never place the concave portion of bowed or warped material against the fence.

English

CROWN MOLDING MITER ANGLES

CROWN TYPE 38°/52° 45°/45° CROWN TYPE 38°/52° 45°/45°

WALL ANGLE MITER/BEVEL MITER/BEVEL WALL ANGLE MITER/BEVEL MITER/BEVEL

100

101

102

103

104

105

106

42.93/41.08

42.39/40.79

41.85/40.50

41.32/40.20

40.79/39.90

40.28/39.61

39.76/39.30

39.25/39.00

38.74/38.69

38.24/38.39

37.74/38.08

37.24/37.76

36.75/37.45

36.27/37.13

35.79/36.81

35.31/36.49

34.83/36.17

34.36/35.85

33.90/35.52

33.43/35.19

32.97/34.86

32.52/34.53

32.07/34.20

31.62/33.86

31.17/33.53

30.73/33.19

30.30/32.85

29.86/32.51

29.43/32.17

29.00/31.82

28.58/31.48

28.16/31.13

27.74/30.78

27.32/30.43

26.91/30.08

26.50/29.73

26.09/29.38

25.69/29.02

25.29/28.67

24.78/28.31

46.89/36.13

46.35/35.89

45.81/35.64

45.28/35.40

44.75/35.15

44.22/34.89

43.70/34.64

43.18/34.38

42.66/34.12

42.15/33.86

41.64/33.60

41.13/33.33

40.62/33.07

40.12/32.80

39.62/32.53

39.13/32.25

38.63/31.98

38.14/31.70

37.66/31.42

37.17/31.14

36.69/30.86

36.21/30.57

35.74/30.29

35.26/30.00

34.79/29.71

34.33/29.42

33.86/29.13

33.40/28.83

32.94/28.54

32.48/28.24

32.02/27.94

31.58/27.64

31.13/27.34

30.68/27.03

30.24/26.73

29.80/26.42

29.36/26.12

28.92/25.81

28.48/25.50

28.05/25.19

107

108

109

110

111

112

113

114

115

116

117

118

119

120

121

122

123

124

125

126

127

128

129

130

131

132

133

134

135

136

137

138

139

140

141

142

143

144

145

146

24.49/27.95

24.10/27.59

23.71/27.23

23.32/26.87

22.93/26.51

22.55/26.15

22.17/25.78

21.79/25.42

21.42/25.05

21.04/24.68

20.67/24.31

20.30/23.94

19.93/23.57

19.57/23.20

19.20/22.83

18.84/22.46

18.48/22.09

18.13/21.71

17.77/21.34

17.42/20.96

17.06/20.59

16.71/20.21

16.37/19.83

16.02/19.45

15.67/19.07

15.33/18.69

14.99/18.31

14.65/17.93

14.30/17.55

13.97/17.17

13.63/16.79

13.30/16.40

12.96/16.02

12.63/15.64

12.30/15.25

11.97/14.87

11.64/14.48

11.31/14.09

10.99/13.71

10.66/13.32

27.62/24.87

27.19/24.56

26.77/24.24

26.34/23.93

25.92/23.61

25.50/23.29

25.08/22.97

24.66/22.65

24.25/22.33

23.84/22.01

23.43/21.68

23.02/21.36

22.61/21.03

22.21/20.70

21.80/20.38

21.40/20.05

21.00/19.72

20.61/19.39

20.21/19.06

19.81/18.72

19.42/18.39

19.03/18.06

18.64/17.72

18.25/17.39

17.86/17.05

17.48/16.71

17.09/16.38

16.71/16.04

16.32/15.70

15.94/15.36

15.56/15.02

15.19/14.68

14.81/14.34

14.43/14.00

14.06/13.65

13.68/13.31

13.31/12.97

12.94/12.62

12.57/12.28

12.20/11.93

English

10" Sliding Compound Miter Saw

Operator’s Manual GMSDR1015LC

CUTTING COMPOUND MITERS

To aid in making the correct settings, the compound angle setting chart below has been provided. Since compound

cuts are the most difﬁcult to obtain the accuracy, make trial cuts on scrap material prior to making your required

cut.

45678910

0°

M-45.00°

B- 0.00°

M-36.00°

B- 0.00°

M-30.00°

B- 0.00°

M-25.71°

B- 0.00°

M-22.50°

B- 0.00°

M-20.00°

B- 0.00°

M-18.00°

B- 0.00°

5°

M-44.89°

B- 3.53°

M-35.90°

B- 2.94°

M-29.91°

B- 2.50°

M-25.63°

B- 2.17°

M-22.42°

B- 1.91°

M-19.93°

B- 1.71°

M-17.94°

B- 1.54°

10°

M-44.56°

B- 7.05°

M-35.58°

B- 5.86°

M-29.62°

B- 4.98°

M-25.37°

B- 4.32°

M-22.19°

B- 3.81°

M-19.72°

B- 3.40°

M-17.74°

B- 3.08°

15°

M-44.01°

B- 10.55°

M-35.06°

B- 8.75°

M-29.15°

B- 7.44°

M-24.95°

B- 6.45°

M-21.81°

B- 5.68°

M-19.37°

B- 5.08°

M-17.42°

B- 4.59°

20°

M-43.22°

B- 14.00°

M-34.32°

B- 11.60°

M-28.48°

B- 8.53°

M-24.35°

B- 8.53°

M-21.27°

B- 7.52°

M-18.88°

B- 6.72°

M-16.98°

B- 6.07°

25°

M-42.19°

B- 17.39°

M-33.36°

B- 14.38°

M-27.62°

B- 12.20°

M-23.56°

B- 10.57°

M-20.58°

B- 9.31°

M-18.26°

B- 8.31°

M-16.98°

B- 7.50°

30°

M-40.89°

B- 20.70°

M-32.18°

B- 17.09°

M-26.57°

B- 14.48°

M-22.64°

B- 12.53°

M-19.73°

B- 11.03°

M-17.50°

B- 9.85°

M-15.72°

B- 8.89°

35°

M-39.32°

B- 23.93°

M-30.76°

B- 19.70°

M-25.31°

B- 16.67°

M-21.53°

B- 14.41°

M-18.74°

B- 12.68°

M-16.60°

B- 11.31°

M-14.90°

B- 10.21°

40°

M-37.45°

B- 27.03°

M-29.10°

B- 22.20°

M-23.86°

B- 18.75°

M-20.25°

B- 16.19°

M-17.60°

B- 14.24°

M-15.58°

B- 12.70°

M-13.98°

B- 11.46°

45°

M-35.26°

B- 30.00°

M-27.19°

B- 24.56°

M-22.21°

B- 20.70°

M-18.80°

B- 17.87°

M-16.32°

B- 15.70°

M-14.43°

B- 14.00°

M-12.94°

B- 12.62°

50°

M-32.73°

B- 32.80°

M-25.03°

B- 26.76°

M-20.36°

B- 22.52°

M-17.20°

B- 19.41°

M-14.91°

B- 17.05°

M-13.17°

B- 15.19°

M-11.80°

B- 13.69°

55°

M-29.84°

B- 35.40°

M-22.62°

B- 28.78°

M-18.32°

B- 24.18°

M-15.44°

B- 20.82°

M-13.36°

B- 18.27°

M-11.79°

B- 16.27°

M-10.56°

B- 14.66°

60°

M-26.57°

B- 37.76°

M-19.96°

B- 30.60°

M-16.10°

B- 25.66°

M-13.54°

B- 22.07°

M-11.70°

B- 19.35°

M-10.31°

B- 17.23°

M-9.23°

B- 15.52°

65°

M-22.91°

B- 39.86°

M-17.07°

B- 32.19°

M-13.71°

B- 26.95°

M-11.50°

B- 23.16°

M-9.93°

B- 20.29°

M-8.74°

B- 18.06°

M-7.82°

B- 16.26°

70°

M-18.88°

B- 41.64°

M-13.95°

B- 33.53°

M-11.17°

B- 28.02°

M-9.35°

B- 24.06°

M-8.06°

B- 21.08°

M-7.10°

B- 18.75°

M-6.34°

B- 16.88°

75°

M-14.51°

B- 43.08°

M-10.65°

B- 34.59°

M-8.50°

B- 28.88°

M-7.10°

B- 24.78°

M-6.12°

B- 21.69°

M-5.38°

B- 19.29°

M-4.81°

B- 17.37°

80°

M-9.85°

B- 44.14°

M-7.19°

B- 35.37°

M-5.73°

B- 29.50°

M-4.78°

B- 25.30°

M-4.11°

B- 22.14°

M-3.62°

B- 19.68°

M-3.23°

B- 17.72°

85°

M-4.98°

B- 44.78°

M-3.62°

B- 35.84°

M-2.88°

B- 29.87°

M-2.40°

B- 25.61°

M- 2.07°

B- 22.41°

M-1.82°

B- 19.92°

M-1.62°

B- 17.93°

90°

M-0.00°

B- 45.00°

M-0.00°

B- 36.00°

M-0.00°

B- 30.00°

M-0.00°

B- 25.71°

M-0.00°

B- 22.50°

M-0.00°

B- 20.00°

M-0.00°

B- 18.00°

NUMBER OF SIDES

PITCH

La page charge ...

Genesis GMSDR1015LC Manuel utilisateur

Marque: Genesis

Modèle: GMSDR1015LC

Catégorie: Scies à onglet

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Genesis GMSDR1015LC User manual
español: Genesis GMSDR1015LC Manual de usuario

Genesis GMSDR1015LC Manuel utilisateur

Genesis GMSDR1015LC Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents