Risco RVCM72P23 Mode d'emploi

RVCM72P23
Risco
Marque
Risco
Modèle
RVCM72P23
Taper
Mode d'emploi
VUpoint
Eyeball 4MP Varifocal PoE
Network Camera
Model: RVCM72P23
Quick Guide
EN
FR
ES
IT
2
Language
Page
3
5
7
9
EN
FR
ES
IT
3
Eyeball Network Camera Components
EN
4
PoE Camera Settings
Note
This camera can be connected to RISCO Cloud only via the VUpoint NVR
Step 1
Connect one end of the network cable (LAN) to the camera Ethernet port and the other side to
your router or an NVR PoE Port. If the camera is not connected to PoE, power it up by an
appropriate power supply.
Step 2
Use the VUpoint NVR instructions to connect the camera to the NVR using “RISCO Pro”
Camera type
Product Specification
Parameter
Description
Image Sensor
1/3” 4Megapixel progressive CMOS
IR Distance
50 m
Focal Length
2.8 – 12 mm
WDR
120 dB
Firmware Upgrade
Via the camera’s web interface
Power Supply
12V DC/POE
Power Consumption
<6.9W
Operating Conditions
-30◦C to 60◦C (-22◦F to 140◦F)/ less than ≤ 95%
Storage Temperature
-40◦C to 60◦C (-40◦F to 140◦F)
Protection
IP67
5
Composants de la caméra IP PoE Eyeball
FR
Réinitialisation
6
Paramètres de la caméra PoE
Remarque
Il est possible de connecter cette caméra au cloud RISCO via le NVR VUpoint.
Étape 1
Raccordez l'une des extrémités du câble Ethernet (LAN) au port Ethernet de la caméra, et
l'autre extrémité à un routeur à un port PoE NVR. Si la caméra n’est pas connectée à un port
PoE, alimentez la avec une alimentation appropriée.
Étape 2
Consultez les instructions du NVR VUpoint pour connecter la caméra au NVR avec le type de
caméra « RISCO Pro ».
Spécifications du produit
Paramètre
Description
Capteur d'image
CMOS 1/3” de 4 Mégapixel progressif
Distance IR
50 m
Focale
2.8 – 12 mm
WDR
120 dB
Mise à jour Firmware
Via l’interface web de la caméra
Alimentation
12V DC/POE
Consommation
<6.9W
Conditions de fonctionnement
-30◦C à 60◦C / moins de ≤ 95%
Température de stockage
-40◦C à 60◦C
Protection
IP67
7
Componentes de la cámara IP Eyeball
ES
Reinicio
8
Configuración de la cámara PoE
Nota
Esta cámara se puede conectar a RISCO Cloud solo a través del NVR de VUpoint
Paso 1
Conecte un extremo del cable Ethernet (LAN) al puerto Ethernet de la cámara y el otro extremo
a un router o un puerto PoE NVR. Si la cámara no está conectada a alimentación PoE, conéctela
a un alimentador adecuado.
Paso 2
Consultar las instrucciones del NVR de VUpoint para conectar la cámara al NVR con el tipo
de cámara “RISCO Pro”.
Especificaciones del producto
Parámetro
Descripción
Sensor de imagen
1/3” 4Megapixel CMOS progresivo
Distancia IR
50 m
Distancia focal
2.8 – 12 mm
WDR
120 dB
Actualización de Firmware
Desde la interfaz web de la cámara
Fuente de alimentación
12V DC/POE
Consumo de energía
<6.9W
Condiciones de funcionamiento
-30◦C a 60◦C/ menos de ≤ 95%
Temperatura de almacenamiento
-40◦C a 60◦C
Protección
IP67
9
Eyeball Network Camera Components
Nota: Per effettuare il reset
(usato per caricare i valori di
default di fabbrica), premere il
tasto Reset per almeno 10
secondi e attendere lo
spegnimento del LED
IT
10
Impostazioni telecamera PoE
Nota
Questa telecamera può essere connessa al cloud RISCO solo via NVR VUpoint
Passo 1
Connettere un capo del cavo di rete (LAN) alla porta Ethernet della telecamera e l’altro capo
alla porta PoE dell’NVR. Se la videocamera non è collegata al PoE, alimentarla tramite un
alimentatore appropriato.
Passo 2
Fare riferimento alle istruzioni dell’NVR VUpoint per connettere la telecamera all’NVR
usando la tipologia di telecamere “RISCO Pro”
Specifiche Tecniche
Parametro
Descrizione
Sensore video
1/3” 4Megapixel progressivo CMOS
Distanza a IR
50 m
Lunghezza Focale
2.8 – 12 mm
WDR
120 dB
Aggiornamento Firmware
Tramite Web server telecamera
Alimentatore
12V DC/POE
Assorbimento
<6.9W
Condizioni Operative
-30◦C a 60◦C/ meno di ≤ 95%
Temperatura de armazenamento
-40◦C a 60◦C
Protezione
IP67
11
EMC Compliance Statement:
Hereby, RISCO Group declares that this equipment is in compliance with the essential requirements and
other relevant provisions of Directive 2014/30/EU. For the CE Declaration of Conformity please refer to
our website: www.riscogroup.com.
Déclaration de Conformité de EMC:
Par la présente, RISCO Group, déclare cet équipement est en conformité aux conditions essentielles et à
d'autres dispositions appropriées de la directive 2014/30/EU.
Vous pouvez trouver la copie complète de la déclaration de conformité à la directive 2014/30/EU sur
notre site web, à l’adresse suivante : www.riscogroup.com.
Declaración de Conformidad EMC :
Por la presente, RISCO Group declara que este equipo cumple con los requisitos esenciales y otras
disposiciones relevantes de la Directiva 2014/30/EU. Para la Declaración de Conformidad CE, por favor
diríjase a nuestra web: www.riscogroup.com.
Dichiarazione di Conformità EMC:
La sottoscritta RISCO Group, dichiara sotto la propria responsabilità che questo prodotto è conforme ai
requisiti essenziali e alle altre rilevanti disposizioni della Direttiva Europea 2014/30/EU.
Per le Dichiarazioni di Conformità CE, visitate il nostro sito web: www.riscogroup.com
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
Changes or modifications to this equipment which are not expressly approved by the party responsible
for compliance (RISCO Group's.) could void the user's authority to operate the equipment.
FCC Note
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment on and off, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on to a different circuit from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
12
Standard Limited Product Warranty (“Limited Warranty”)
RISCO Ltd. (“RISCO") guarantee RISCO’s hardware products (“Products”) to be free from defects in
materials and workmanship when used and stored under normal conditions and in accordance with the
instructions for use supplied by RISCO, for a period of (i) 24 months from the date of delivery of the
Product ( the “Warranty Period”). This Limited Warranty covers the Product only within the country
where the Product was originally purchased and only covers Products purchased as new.
Contact with customers only. This Limited Warranty is solely for the benefit of customers who
purchased the Products directly from RISCO or from an authorized distributor of RISCO. RISCO does not
warrant the Product to consumers and nothing in this Warranty obligates RISCO to accept Product
returns directly from end users who purchased the Products for their own use from RISCO’s customer or
from any installer of RISCO, or otherwise provide warranty or other services to any such end user
directly. RISCO’s authorized distributor or installer shall handle all interactions with its end users in
connection with this Limited Warranty. RISCO’s authorized distributor or installer shall make no
warranties, representations, guarantees or statements to its end users or other third parties that suggest
that RISCO has any warranty or service obligation to, or any contractual privy with, any recipient of a
Product.
Remedies. In the event that a material defect in a Product is discovered and reported to RISCO during
the Warranty Period, RISCO shall accept return of the defective Product in accordance with the below
RMA procedure and, at its option, either (i) repair or have repaired the defective Product, or (ii) provide a
replacement product to the customer.
Return Material Authorization. In the event that you need to return your Product for repair or
replacement, RISCO will provide you with a Return Merchandise Authorization Number (RMA#) as well
as return instructions. Do not return your Product without prior approval from RISCO. Any Product
returned without a valid, unique RMA# will be refused and returned to the sender at the sender’s
expense. The returned Product must be accompanied with a detailed description of the defect discovered
(“Defect Description”) and must otherwise follow RISCO’s then-current RMA procedure published in
RISCO’s website at www.riscogroup.com in connection with any such return. If RISCO determines in its
reasonable discretion that any Product returned by customer conforms to the applicable warranty (“Non-
Defective Product”), RISCO will notify the customer of such determination and will return the applicable
Product to customer at customer’s expense. In addition, RISCO may propose and assess customer a
charge for testing and examination of Non-Defective Product.
Entire Liability. The repair or replacement of Products in accordance with this Limited Warranty shall be
RISCO’s entire liability and customer’s sole and exclusive remedy in case a material defect in a Product is
discovered and reported as required herein. RISCO’s obligation and this Limited Warranty are contingent
upon the full payment by customer for such Product and upon a proven weekly testing and examination
of the Product functionality.
13
Limitations. This Limited Warranty is the only warranty made by RISCO with respect to the Products.
The warranty is not transferable to any third party. To the maximum extent permitted by applicable law,
this Limited Warranty shall not apply and will be void if: (i) the conditions set forth above are not met
(including, but not limited to, full payment by customer for the Product and a proven weekly testing and
examination of the Product functionality); (ii) if the Products or any part or component thereof: (a) have
been subjected to improper operation or installation; (b) have been subject to neglect, abuse, willful
damage, abnormal working conditions, failure to follow RISCO’s instructions (whether oral or in
writing); (c) have been misused, altered, modified or repaired without RISCO’s written approval or
combined with, or installed on products, or equipment of the customer or of any third party; (d) have
been damaged by any factor beyond RISCO’s reasonable control such as, but not limited to, power
failure, electric power surges, or unsuitable third party components and the interaction of software
therewith or (e) any failure or delay in the performance of the Product attributable to any means of
communication provided by any third party service provider, including, but not limited to, GSM
interruptions, lack of or internet outage and/or telephony failure. BATTERIES ARE EXPLICITLY
EXCLUDED FROM THE WARRANTY AND RISCO SHALL NOT BE HELD RESPONSIBLE OR LIABLE
IN RELATION THERETO, AND THE ONLY WARRANTY APPLICABLE THERETO, IF ANY, IS THE
BATTERY MANUFACTURER'S WARRANTY. RISCO does not install or integrate the Product in the end
user’s security system and is therefore not responsible for and cannot guarantee the performance of the
end user’s security system which uses the Product or which the Product is a component of.
This Limited Warranty applies only to Products manufactured by or for RISCO. Further, this Limited
Warranty does not apply to any software (including operating system) added to or provided with the
Products or any third-party software, even if packaged or sold with the RISCO Product. Manufacturers,
suppliers, or third parties other than RISCO may provide their own warranties, but RISCO, to the extent
permitted by law and except as otherwise specifically set forth herein, provides its Products “AS IS”.
Software and applications distributed or made available by RISCO in conjunction with the Product (with
or without the RISCO brand), including, but not limited to system software, as well as P2P services or
any other service made available by RISCO in relation to the Product, are not covered under this Limited
Warranty. Refer to the Terms of Service at: https://riscocloud.com/ELAS/WebUI/UserLogin/License for
details of your rights and obligations with respect to the use of such applications, software or any service.
RISCO does not represent that the Product may not be compromised or circumvented; that the Product
will prevent any personal injury or property loss by burglary, robbery, fire or otherwise, or that the
Product will in all cases provide adequate warning or protection. A properly installed and maintained
alarm may only reduce the risk of a burglary, robbery or fire without warning, but it is not insurance or a
guarantee that such will not occur or will not cause or lead to personal injury or property loss.
CONSEQUENTLY, RISCO SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY, PROPERTY
DAMAGE OR OTHER LOSS BASED ON ANY CLAIM AT ALL INCLUDING A CLAIM THAT THE
PRODUCT FAILED TO GIVE WARNING.
14
EXCEPT FOR THE WARRANTIES SET FORTH HEREIN, RISCO AND ITS LICENSORS HEREBY
DISCLAIM ALL EXPRESS, IMPLIED OR STATUTORY, REPRESENTATIONS, WARRANTIES,
GUARANTEES, AND CONDITIONS WITH REGARD TO THE PRODUCTS, INCLUDING BUT NOT
LIMITED TO ANY REPRESENTATIONS, WARRANTIES, GUARANTEES, AND CONDITIONS OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE AND WARRANTIES
AGAINST HIDDEN OR LATENT DEFECTS, TO THE EXTENT PERMITTED BY LAW. WITHOUT
LIMITING THE GENERALITY OF THE FOREGOING, RISCO AND ITS LICENSORS DO NOT
REPRESENT OR WARRANT THAT: (I) THE OPERATION OR USE OF THE PRODUCT WILL BE
TIMELY, SECURE, UNINTERRUPTED OR ERROR-FREE; (ii) THAT ANY FILES, CONTENT OR
INFORMATION OF ANY KIND THAT MAY BE ACCESSED THROUGH THE PRODUCT SHALL
REMAIN SECURED OR NON DAMAGED. CUSTOMER ACKNOWLEDGES THAT NEITHER RISCO
NOR ITS LICENSORS CONTROL THE TRANSFER OF DATA OVER COMMUNICATIONS
FACILITIES, INCLUDING THE INTERNET, GSM OR OTHER MEANS OF COMMUNICATIONS AND
THAT RISCO’S PRODUCTS, MAY BE SUBJECT TO LIMITATIONS, DELAYS, AND OTHER PROBLEMS
INHERENT IN THE USE OF SUCH MEANS OF COMMUNICATIONS. RISCO IS NOT RESPONSIBLE
FOR ANY DELAYS, DELIVERY FAILURES, OR OTHER DAMAGE RESULTING FROM SUCH
PROBLEMS. RISCO WARRANTS THAT ITS PRODUCTS DO NOT, TO THE BEST OF ITS
KNOWLEDGE, INFRINGE UPON ANY PATENT, COPYRIGHT, TRADEMARK, TRADE SECRET OR
OTHER INTELLECTUAL PROPERTY RIGHT IN ANY EVENT RISCO SHALL NOT BE LIABLE FOR
ANY AMOUNTS REPRESENTING LOST REVENUES OR PROFITS, PUNITIVE DAMAGES, OR FOR
ANY OTHER INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF THEY
WERE FORESEEABLE OR RISCO HAS BEEN INFORMED OF THEIR POTENTIAL.
15
Contacting RISCO
RISCO Group is committed to customer service and Product support. You can contact us through our
website (www.riscogroup.com) or at the following telephone and fax numbers:
United Kingdom
Tel: +44-(0)-161-655-5500
support-uk@riscogroup.com
Belgium (Benelux)
Tel: +32-2522-7622
support-be@riscogroup.com
Italy
Tel: +39-02-66590054
support-it@riscogroup.com
USA
Tel: +1-631-719-4400
support-usa@riscogroup.com
Spain
Tel: +34-91-490-2133
support-es@riscogroup.com
China
Tel: +86-755-82789285
support-cn@riscogroup.com
France
Tel: +33-164-73-28-50
support-fr@riscogroup.com
Israel
Tel: +972-3-963-7777
support@riscogroup.com
All rights reserved.
No part of this document may be reproduced in any form without prior written permission from the
publisher.
16
© RISCO Group, 12/2020. All rights reserved. 5IN2897 B
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Risco RVCM72P23 Mode d'emploi

RVCM72P23
Risco
Marque
Risco
Modèle
RVCM72P23
Taper
Mode d'emploi
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents