Wolf E Series Manuel utilisateur

E SERIES BUILT-IN OVENS

INSTALLATION INSTRUCTIONS

INSTRUCCIONES DE INSTALACIÓN

INSTRUCTIONS D’INSTALLATION

ISTRUZIONI PER L’INSTALLAZIONE

INSTALLATIONSANWEISUNGEN

ENGLISH 4

ESPÃNOL 22

FRANÇAIS 40

ITALIANO 58

DEUTSCH 76

3

As you follow these instruc tions, you will

notice WARNING and CAUTION symbols.

This blocked information is impor tant for the

safe and efficient installation of Wolf equip-

ment. There are two types of potential

hazards that may occur during installation.

Another footnote we would like to identify is

IMPORTANT NOTE: This highlights information

that is especially relevant to a problem-free

installation.

signals a situation where minor injury or

product damage may occur if you do not

follow instructions.

states a hazard that may cause serious

injury or death if precautions are not

followed.

WOLF

®

is a registered trademark of Wolf Appliance, Inc.

CONTACT

INFORMATION

Website:

wolfappliance.com

INSTALLATION REQUIREMENTS

IMPORTANT NOTE: This installation must be

completed by a qualified technician.

IMPORTANT NOTE:

Save these Installation

Instructions for the local inspector’s use.

Please read the entire Installation Instruc-

tions prior to installation.

Installer:

please retain these instructions

for local inspector’s reference, then leave

them with the homeowner.

Homeowner:

please read and keep these

instructions for future reference and be sure

to read the entire Use & Care Information

prior to use.

IMPORTANT NOTE:

This appliance must be

installed in accordance with all local codes.

The correct voltage, frequency and amperage

must be supplied to the appliance from a dedi-

cated, grounded circuit which is protected by a

properly sized circuit breaker or time delay

fuse. The proper voltage, frequency, and

amperage ratings are listed on the product

rating plate.

Record the model and serial numbers before

installing the built-in oven. Both numbers are

listed on the rating plate, located on the right

side of the oven trim, directly above the door.

Open the oven door to view the rating plate.

Refer to the illustration below.

WOLF E SERIES BUILT-IN OVENS

SITE PREPARATION

IMPORTANT NOTE:

A minimum 610 mm of

usable cabinet depth is required, or the back

panel of the cabinet may need to be removed

for proper installation. A minimum 635 mm of

usable cabinet depth is required for a flush

inset installation. The electrical box must be

flush with the back panel of the cabinet.

The installation opening must have a flat, level

base platform to support the oven. Single

ovens require a minimum base support of

113 kg and double ovens require a minimum

base support of 181 kg.

IMPORTANT NOTE:

Wolf built-in ovens are

designed and agency approved for installation

with Wolf cooktops, microwaves and warming

drawers only. The nominal width of the built-in

oven should match the nominal width of the

cooktop. A built-in oven cannot be installed

below a Wolf rangetop.

RATING PLATE

INFORMATION

Model Number

Serial Number

Rating plate location

Location

of rating

plate

5

WOLF E SERIES BUILT-IN OVENS

E SERIES BUILT-IN SINGLE OVENS

MODELS ICBSO30-2F/S AND

ICBSO30-2U/S

IMPORTANT NOTE:

A minimum 610 mm of

usable cabinet depth is required, or the back

panel of the cabinet may need to be removed

for proper installation. A minimum 635 mm of

usable cabinet depth is required for a flush

inset installation. The electrical box must be

flush with the back panel of the cabinet.

For ease of installation, Wolf recommends

using 838 mm wide cabinets with the E Series

single oven. A minimum 838 mm wide cabinet

is required for a flush inset installation. The

cabinet base platform must be able to support

113 kg.

Refer to the following illustrations for overall

dimensions, installation specifications and

electrical location for the E Series single oven.

The E Series single oven requires a separate,

grounded 3-wire 220-240 V AC, 50/60 Hz, 30

amp service with its own circuit breaker. Refer

to Electrical Requirements on page 16. The

oven is not supplied with an electrical plug.

IMPORTANT NOTE:

Unless you are using

cabinets deeper than 610 mm for a standard

installation or 635 mm for a flush inset installa-

tion, it is recommended that the electrical

supply be placed in an adjacent cabinet.

Choose the location shown in the installation

illustrations on pages 8–9 that best suits your

installation.

603 mm

BEHIND FRAME

708 mm

718 mm

759 mm

603 mm

CONDUIT

CHANNEL

OPEN OVEN DOOR

TOP VIEW

559 mm

32 mm

25 mm

48 mm

RIGHT SIDE VIEW

687 mm

759 mm

67 mm

OVERALL DIMENSIONS – MODELS ICBSO30-2F/S AND ICBSO30-2U/S

Unframed Model ICBSO30-2U/S shown.

6

INSTALLATION INSTRUCTIONS

E SERIES BUILT-IN SINGLE OVENS

STANDARD INSTALLATION

IMPORTANT NOTE:

For standard installations,

a minimum 610 mm of usable cabinet depth is

required, or the back panel of the cabinet may

need to be removed for proper installation.

The electrical box must be flush with the back

panel of the cabinet.

For standard installations, the E Series built-in

oven is installed by inserting into cabinetry

from the front. The oven has a face trim on all

four sides and will overlap stiles and rails. The

trim overlaps 3 mm on the bottom, 8 mm on

the top and 19 mm on each side.

FLUSH INSET INSTALLATION

IMPORTANT NOTE:

For flush inset installa-

tions, a minimum 635 mm of usable cabinet

depth is required, or the back panel of the

cabinet may need to be removed for proper

installation. The electrical box must be flush

with the back panel of the cabinet.

The flush inset installation requires the built-in

oven to be recessed into the cabinet. A

minimum 838 mm wide and 635 mm deep

cabinet is needed if you want the front of the

oven to be flush with surrounding cabinetry.

IMPORTANT NOTE:

For flush inset installa-

tions, the inside edges of the rough opening

must be finished, as they will be exposed

when the oven door is open. These edges

should be stained instead of having a lami-

nated surface, to avoid damage from high

temperatures during self-clean.

COMBINATION INSTALLATIONS

The Wolf E Series single oven may be installed

below a Wolf 762 mm induction, electric or gas

cooktop. Unless you are using cabinets deeper

than 610 mm for a standard installation or 635

mm for a flush inset installation, it is recom-

mended that the electrical supply be placed in

the base cabinet to the right of the oven. The E

Series single oven may also be installed below

a Wolf 914 mm induction, electric or gas

cooktop.

A Wolf E Series single oven may be installed

next to another E Series single oven. You must

allow for a 64 mm space between the oven

rough openings. Also, a separate inner wall is

required for each oven between openings.

7

WOLF E SERIES BUILT-IN OVENS

E SERIES BUILT-IN SINGLE OVENS

691 mm

OPENING

HEIGHT

724 mm

OPENING WIDTH

127

mm

102

mm

610 mm

OPENING DEPTH

E E

E

838 mm

RECOMMENDED CABINET WIDTH

762 mm min

ELECTRICAL LOCATION

WITHIN OPENING

APPLIES ONLY TO

CABINETS DEEPER

THAN 610 mm

E

127

mm

121 mm min

838 mm

RECOMMENDED CABINET WIDTH

762 mm min

95 mm min

914 mm

STANDARD

FLOOR TO

COUNTER

HEIGHT

691 mm

OPENING

HEIGHT

724 mm

OPENING WIDTH

102

mm

610 mm min

OPENING DEPTH

ELECTRICAL

LOCATION WITHIN

OPENING APPLIES

ONLY TO CABINETS

DEEPER THAN 610 mm

STANDARD INSTALLATION

Overall Oven Width 759 mm

Overall Oven Height 708 mm

Overall Oven Depth (behind frame) 603 mm

Open Door Clearance 559 mm

Recommended Cabinet Width 838 mm

Minimum Cabinet Width 762 mm

Minimum Cabinet (Opening) Depth 610 mm

Opening Width 724 mm

Opening Height 691 mm

Minimum Base Support 113 kg

STANDARD INSTALLATION – MODELS ICBSO30-2F/S AND ICBSO30-2U/S

8

INSTALLATION INSTRUCTIONS

E SERIES BUILT-IN SINGLE OVENS

FLUSH INSET INSTALLATION

Overall Oven Width 759 mm

Overall Oven Height 708 mm

Overall Oven Depth (behind frame) 603 mm

Open Door Clearance 559 mm

Minimum Base Support 113 kg

Minimum Cabinet Width 838 mm

Minimum Flush Inset Depth 635 mm

Opening Width 724 mm

Minimum Flush Inset Width 772 mm

Opening Height 691 mm

Minimum Flush Inset Height 724 mm

FLUSH INSET INSTALLATION – MODELS ICBSO30-2F/S AND ICBSO30-2U/S

691 mm

OPENING

HEIGHT

724 mm

min

FLUSH

INSET

HEIGHT

772 mm

FLUSH INSET WIDTH

724 mm

OPENING WIDTH

127

mm

102

mm

E

914 mm

RECOMMENDED CABINET WIDTH

838 mm min

610 mm

min

OPENING

DEPTH

25 mm

635 mm

min

FLUSH

INSET

DEPTH

11 mm

22 mm

ELECTRICAL LOCATION

WITHIN OPENING

APPLIES ONLY TO

CABINETS DEEPER

THAN 635 mm

SIDE VIEW

TOP VIEW

IMPORTANT

NOTE

For flush inset

installations, the

inside edges of the

rough opening

must be finished,

as they will be

exposed when the

oven door is open.

9

WOLF E SERIES BUILT-IN OVENS

E SERIES BUILT-IN DOUBLE OVENS

MODELS ICBDO30-2F/S AND

ICBDO30-2U/S

IMPORTANT NOTE:

A minimum 610 mm of

usable cabinet depth is required, or the back

panel of the cabinet may need to be removed

for proper installation. A minimum 635 mm of

usable cabinet depth is required for a flush

inset installation. The electrical box must be

flush with the back panel of the cabinet.

For ease of installation, Wolf recommends

using 838 mm wide cabinets with the E Series

double oven. A minimum 838 mm wide

cabinet is required for a flush inset installation.

The cabinet base platform must be able to

support 181 kg.

Refer to the following illustrations for overall

dimensions, installation specifications and

electrical location for the E Series double oven.

The E Series double oven requires a separate,

grounded 3-wire 220-240 V AC, 50/60 Hz, 50

amp service with its own circuit breaker. Refer

to Electrical Requirements on page 16. The

oven is not supplied with an electrical plug.

603 mm

BEHIND FRAME

1280 mm 1257 mm

718 mm

759 mm

603 mm

OPEN OVEN DOOR

TOP VIEW

67 mm

559 mm

32 mm

25 mm

48 mm

RIGHT SIDE VIEW

759 mm

CONDUIT

CHANNEL

OVERALL DIMENSIONS – MODELS ICBDO30-2F/S AND ICBDO30-2U/S

IMPORTANT NOTE:

Unless you are using

cabinets deeper than 610 mm for a standard

installation or 635 mm for a flush inset installa-

tion, it is recommended that the electrical

supply be placed in an adjacent cabinet.

Choose the location shown in the installation

illustrations on pages 12–13 that best suits

your installation.

Unframed Model ICBDO30-2U/S shown.

10

INSTALLATION INSTRUCTIONS

E SERIES BUILT-IN DOUBLE OVENS

STANDARD INSTALLATION

IMPORTANT NOTE:

For standard installations,

a minimum 610 mm of usable cabinet depth is

required, or the back panel of the cabinet may

need to be removed for proper installation.

The electrical box must be flush with the back

panel of the cabinet.

For standard installations, the E Series built-in

oven is installed by inserting into cabinetry

from the front. The oven has a face trim on all

four sides and will overlap stiles and rails. The

trim overlaps 3 mm on the bottom, 8 mm on

the top and 19 mm on each side.

FLUSH INSET INSTALLATION

IMPORTANT NOTE:

For flush inset installa-

tions, a minimum 635 mm of usable cabinet

depth is required, or the back panel of the

cabinet may need to be removed for proper

installation. The electrical box must be flush

with the back panel of the cabinet.

The flush inset installation requires the built-in

oven to be recessed into the cabinet. A

minimum 838 mm wide and 635 mm deep

cabinet is needed if you want the front of the

oven to be flush with surrounding cabinetry.

IMPORTANT NOTE:

For flush inset installa-

tions, the inside edges of the rough opening

must be finished, as they will be exposed

when the oven doors are open. These edges

should be stained instead of having a lami-

nated surface, to avoid damage from high

temperatures during self-clean.

11

WOLF E SERIES BUILT-IN OVENS

E SERIES BUILT-IN DOUBLE OVENS

127

mm

E

724 mm

OPENING WIDTH

102

mm

E

838 mm

RECOMMENDED CABINET WIDTH

762 mm min

1260 mm

OPENING

HEIGHT

610 mm min

OPENING DEPTH

1702 mm

typical

ELECTRICAL LOCATION

WITHIN OPENING

APPLIES ONLY TO

CABINETS DEEPER

THAN 610 mm

STANDARD INSTALLATION

Overall Oven Width 759 mm

Overall Oven Height 1292 mm

Overall Oven Depth (behind frame) 603 mm

Open Door Clearance 559 mm

Recommended Cabinet Width 838 mm

Minimum Cabinet Width 762 mm

Minimum Cabinet (Opening) Depth 610 mm

Opening Width 724 mm

Opening Height 1260 mm

Minimum Base Support 181 kg

STANDARD INSTALLATION – MODELS ICBDO30-2F/S AND ICBDO30-2U/S

12

INSTALLATION INSTRUCTIONS

E SERIES BUILT-IN DOUBLE OVENS

FLUSH INSET INSTALLATION

Overall Oven Width 759 mm

Overall Oven Height 1292 mm

Overall Oven Depth (behind frame) 603 mm

Open Door Clearance 559 mm

Minimum Base Support 181 kg

Minimum Cabinet Width 838 mm

Minimum Flush Inset Depth 635 mm

Opening Width 724 mm

Minimum Flush Inset Width 772 mm

Opening Height 1260 mm

Minimum Flush Inset Height 1294 mm

FLUSH INSET INSTALLATION – MODELS ICBDO30-2F/S AND ICBDO30-2U/S

1260 mm

OPENING

HEIGHT

1294 mm

min

FLUSH

INSET

HEIGHT

772 mm min

FLUSH INSET WIDTH

724 mm

OPENING WIDTH

127

mm

102

mm

E

914 mm

RECOMMENDED CABINET WIDTH

838 mm min

610 mm

min

OPENING

DEPTH

25 mm

635 mm

min

FLUSH

INSET

DEPTH

11 mm

22 mm

ELECTRICAL LOCATION

WITHIN OPENING

APPLIES ONLY TO

CABINETS DEEPER

THAN 635 mm

1702 mm

typical

SIDE VIEW

TOP VIEW

IMPORTANT

NOTE

For flush inset

installations, the

inside edges of the

rough opening

must be finished,

as they will be

exposed when the

oven doors are

open.

13

WOLF E SERIES BUILT-IN OVENS

STANDARD INSTALLATION OPTIONS

E SERIES BUILT-IN SINGLE OVEN

The Wolf E Series single oven may be installed

in combination with a Wolf convection or non-

convection microwave oven with 762 mm

E Series trim kit, and a Wolf warming drawer

with E Series stainless steel drawer front or

integrated drawer front. Refer to the illustra-

tion below, and pages 6–9 for installation spec-

ifications for E Series single ovens.

Keep in mind that the size of the custom

panel for the warming drawer with integrated

drawer front will vary according to the

specific installation. Refer to the installation

instructions provided with the microwave trim

kit and warming drawer front for detailed

specifications. Dimensions will vary according

to the specific installation.

727 mm

WARMING DRAWER

OPENING WIDTH

127

mm

102 mm

E

60 mm

691 mm

610 mm

min

691 mm

NOTE: Unless you are using cabinets deeper than 610 mm, it is recommended that the

electrical supply for the oven be placed in an adjacent cabinet.

51 mm

x

51 mm

ANTI-TIP BLOCK

232 mm

606 mm

min

610 mm

min

232 mm

606 mm

min

ANTI-TIP BLOCK APPLICATIONPLATFORM APPLICATION

22 mm

PLATFORM

22 mm

724 mm

OVEN OPENING WIDTH

127

mm

102

mm

E E

ELECTRICAL LOCATION

WITHIN OPENING

APPLIES ONLY TO

CABINETS DEEPER

THAN 610 mm

25 mm

min

511 mm

min

475 mm

25 mm

min

511 mm

min

475 mm

699 mm

MICROWAVE

OPENING WIDTH

127

mm

102 mm

E

838 mm

RECOMMENDED CABINET WIDTH

762 mm

min

STANDARD INSTALLATION – MODELS ICBSO30-2F/S AND ICBSO30-2U/S

Single oven installed with convection microwave with 762 mm E Series trim and warming drawer with E Series stainless

steel drawer front.

14

STANDARD INSTALLATION OPTIONS

E SERIES BUILT-IN DOUBLE OVEN

The Wolf E Series double oven may be

installed in combination with a Wolf warming

drawer with E Series stainless steel drawer

front or integrated drawer front. Refer to the

illustration below, and pages 10–13 for installa-

tion specifications for E Series double ovens.

727 mm

WARMING DRAWER

OPENING WIDTH

127

mm

102 mm

E

NOTE: Unless you are using cabinets deeper than 610 mm, it is recommended that th

e

electrical supply for the oven be placed in an adjacent cabinet.

ANTI-TIP BLOCK APPLICATIONPLATFORM APPLICATION

22 mm

PLATFORM

232 mm

606 mm min

22 mm

60 mm

51 mm x 51 mm

ANTI-TIP BLOCK

232 mm

606 mm min

838 mm

RECOMMENDED CABINET WIDTH

762 mm min

127

mm

E

724 mm

OVEN OPENING WIDTH

102

mm

E

ELECTRICAL LOCATION

WITHIN OPENING

APPLIES ONLY TO

CABINETS DEEPER

THAN 24" (610)

1260 mm

610 mm min

1260 mm

610 mm min

STANDARD INSTALLATION – MODELS ICBDO30-2F/S AND ICBDO30-2U/S

Keep in mind that the size of the custom

panel for the warming drawer with integrated

drawer front will vary according to the

specific installation. Refer to the installation

instructions provided with the warming drawer

front for detailed specifications. Dimensions

will vary according to the specific installation.

Double oven installed above

warming drawer with E Series stainless steel drawer front.

INSTALLATION INSTRUCTIONS

15

WOLF E SERIES BUILT-IN OVENS

IMPORTANT

NOTE

Be aware of local

codes and ordi-

nances when

installing your

service.

E SERIES SINGLE OVENS

Required power supply:

220-240V AC, 50/60 Hz

Maximum connected load:

5.1 kW

Total amps:

21 amps

Minimum supply wire size:

L1, N and

ground–10 AWG

E SERIES DOUBLE OVENS

Required power supply:

220-240V AC, 50/60 Hz

Maximum connected load:

8.9 kW

Refer to the wiring diagram showing the

connections for each lead to the terminal box

on the unit.

ELECTRICAL REQUIREMENTS

The complete appliance must be properly

grounded at all times when electrical

power is applied.

NOTE: Improper connection can result in

a fire hazard.

GROUND

L1

N

Wiring diagram

Verify that power is disconnected from

the electrical box before proceeding.

Open the terminal box to expose the screws

with corresponding numbers. Loosen the 1, 5,

and ground screws. Run the cord through the

strain relief hole and into the terminal box.

Attach the Neutral wire to the number 1

position. Line should be attached to the 5

position and attach the ground to the corre-

sponding ground screw. After tightening the

screws, tighten down the cord strain relief and

close the cover to the terminal box without

pinching any of the wires.

16

INSTALLATION INSTRUCTIONS

ELECTRICAL REQUIREMENTS

With the oven positioned directly in front of

the cabinet opening, feed the properly rated

cord attached to the oven terminal box

through the opening in the cabinet platform

(where applicable). Then, depending upon

local codes, utilize one of the following tech-

niques to connect the appliance to the electri-

cal power supply.

INSTALLING THE OVEN

UNPACK THE OVEN

Cut the plastic straps and remove the two

V-boards. Remove the four top foam corners

and the corner posts. Remove the carton

sleeve by lifting the sleeve up and over the

appliance.

Remove all oven racks, oven rack guides and

broiler pan from inside the oven cavity. For the

double oven, be sure to do this for both the

upper and lower ovens.

Remove the four bottom corners. Use caution

as the oven is not mounted to the shipping

base. Keep the bottom foam in place when

moving or carting the oven. The bottom foam

also protects the factory-installed trim.

IMPORTANT NOTE:

Before moving the oven,

protect any finished flooring with appropriate

materials to avoid damage to the floor.

Remove and discard all packing materials,

including cardboard and tape on the outside of

the oven and inside the oven cavity.

Oven is not mounted to the shipping

base. Do not remove banding until the

oven is at the point of installation.

Do not remove the bottom foam until

oven has been positioned next to the

installation opening.

Do not lift the unit by the oven door

handle(s). This will damage the oven door

and hinges.

17

WOLF E SERIES BUILT-IN OVENS

POSITION THE OVEN

Holding the oven by the upper edge and

bottom side of the oven chassis, carefully lift

the oven up to the cabinet opening.

Resting the oven on the cabinet base platform,

slide the oven into the opening until it is

approximately 152 mm from full insertion. If

applicable, ensure that the installer supplied

cable slides through the opening in the cabinet

platform as the oven is slid into place.

IMPORTANT NOTE:

The installer supplied

cable must be placed in the recessed area

located along the right rear vertical edge of the

oven. Make sure that the cable is not trapped

between the oven and the inner cabinet wall.

Do not block the oven air exhaust located

at the bottom of the oven. Blocking the

exhaust may cause cabinet damage and

poor baking performance.

The oven is very heavy—use caution

when lifting. It is recommended that two

people lift and position the oven into the

opening. Wear gloves to protect hands

from any sharp edges.

INSTALLING THE OVEN

OVEN DOOR REMOVAL

To reduce the weight of the oven and ease

installation, removal of the oven door(s) is an

option.

To Remove Oven Door:

Open oven door all the way.

Flip down the hinge latch on each side.

Close the oven door as far as it will shut.

While holding the oven door on each side

with both hands, lift the oven door up.

Continue to push the oven door closed and

pull it away from the oven frame.

To Reinstall Oven Door:

Insert both hanger arms into the oven

frame openings.

Open the oven door. You should hear a

”click” as the door is set into place.

Move the hinge levers back to the locked

position. Ensure that the door is free to

open and close. If not, repeat the removal

and reinstallation procedures.

18

INSTALLATION INSTRUCTIONS

INSTALLING THE OVEN

MOUNT OVEN TO CABINETRY

Once the oven is fully inserted into the cabinet

opening, locate the mounting holes on the

oven side trim. There will be four mounting

holes for a single oven and six for a double

oven. Refer to the illustration below. Use a

2 mm drill bit to drill pilot holes into the

cabinet. Use the provided wood screws to

secure the oven to the cabinet through the

oven mounting holes.

OVEN OPERATION

IMPORTANT NOTE:

Prior to operating the

oven, be sure to read the entire Wolf E Series

Built-In Ovens Use & Care Information

included with the oven for important safety

information.

Unpack the box containing the oven compo-

nents found in each oven cavity. Install the

oven rack guides onto the shoulder screws

located on the interior side walls of the oven.

Slide the oven racks onto the support racks

within the oven. There are three racks per

oven. Place the broiler pan and grid on a rack

within the oven, if desired.

Turn on the power supply to the oven. Set the

time of day by pressing the

SET CLOCK

touch pad, input the desired time by using the

number pads, then touch

ENTER

.

Select any of the ten cooking modes on the

control panel. Verify that the oven is coming

up to temperature. For the double oven, be

sure to verify operation of both ovens.

IMPORTANT NOTE:

A small amount of smoke

and odor may be noticed during the initial

break-in period. Refer to the Use & Care

Information for additional information.

Failure to install the mounting screws

may cause the oven to move or tip

forward during use. This may result in

damage to the oven or personal injury.

Location of mounting holes

19

CONTACT

INFORMATION

Website:

wolfappliance.com

TROUBLESHOOTING

IMPORTANT NOTE:

If the built-in oven does

not operate properly, follow these trouble-

shooting steps:

Verify that power is being supplied to the

oven.

Check the electrical connections to ensure

that the installation has been completed

correctly.

Follow troubleshooting procedures as

described in the Wolf E Series Built-In

Ovens Use & Care Information.

If the oven still does not work, contact a

Wolf authorized service center. Do not

attempt to repair the oven yourself. Wolf

is not responsible for service required to

correct a faulty installation.

WIRING DIAGRAM

The wiring diagram covering the control circuit

is located on the top of the oven in a sealed

plastic bag.

WOLF E SERIES BUILT-IN OVENS

IF YOU NEED SERVICE

For service in your area, contact either your

Wolf dealer or visit the Showroom Locator

section of our website, wolfappliance.com

to find the regional distributor by country.

When calling for service, you will need the

built-in oven model and serial numbers.

Both numbers are listed on the product

rating plate, located on the right side of the

oven trim, directly above the door. Open

the oven door to view the rating plate.

Refer to the illustration on page 5 for

location of the rating plate.

20

La page charge ...

Wolf E Series Manuel utilisateur

Ce manuel convient également à

Wolf E Series Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents