Rockwell Automation 1785-L80E Manuel utilisateur

Marque: Rockwell Automation

Modèle: 1785-L80E

Taper: Manuel utilisateur

Ce manuel convient également à

Quick Start

Ethernet PLC-5

Programmable

Controller

(Cat. No. 1785-L20E,

-L40E, -L80E)

Allen-Bradley

Important User

Information

Because of the variety of uses for the products described in this

publication, those responsible for the application and use of this

control equipment must satisfy themselves that all necessary steps

have been taken to assure that each application and use meets all

performance and safety requirements, including any applicable laws,

regulations, codes and standards.

The illustrations, charts, sample programs and layout examples

shown in this guide are intended solely for purposes of example.

Since there are many variables and requirements associated with any

particular installation, Allen-Bradley does not assume responsibility

or liability (to include intellectual property liability) for actual use

based upon the examples shown in this publication.

Allen-Bradley publication SGI-1.1, Safety Guidelines for the

Application, Installation, and Maintenance of Solid-State Control

(available from your local Allen-Bradley office), describes some

important differences between solid-state equipment and

electromechanical devices that should be taken into consideration

when applying products such as those described in this publication.

Reproduction of the contents of this copyrighted publication, in

whole or in part, without written permission of Allen-Bradley

Company, Inc., is prohibited.

Throughout this manual we use notes to make you aware of safety

considerations:

Attention statements help you to:

• identify a hazard

• avoid the hazard

• recognize the consequences

Important: Identifies information that is critical for successful

application and understanding of the product.

PLC, PLC-5/11, -5/20, -5/30, -5/40, -5/40L, -5/60, -5/80, PLC-5, and DH+ are trademarks of Allen-Bradley Company, Inc

ATTENTION: Identifies information about practices

or circumstances that can lead to personal injury or

death, property damage or economic loss.

Publication 1785-10.5 - November 1998

Preface

Read this preface to familiarize yourself with the rest of the manual.

This preface covers the following topics:

• who should use this manual

• the purpose of this manual

• how to use this manual

• conventions used in this manual

• Rockwell Automation support

Who Should Use

This Manual

To use this manual, you should understand programmable controllers

and be able to interpret the ladder logic instructions required to

control your application. For more information, see the documents

listed on the following page or contact your local Rockwell

Automation representative.

Purpose of This Manual This manual is for users of the Ethernet PLC-5® processor. It:

• presents you with the basic information you need to get your

system up and running

• provides “memory jogger” information, such as specific bit and

switch settings for modules

• includes high-level procedures with cross-references to other

manuals for more detail

How to Obtain a User Manual There is a user manual associated with this product that contains

detailed information about configuring, programming, and using a

PLC-5 processor. To obtain a copy of the Enhanced and Ethernet

PLC-5 Programmable Controllers User Manual, publication number

1785-6.5.12, you can either:

• view or download an electronic version from the internet:

www.theautomationbookstore.com

• purchase a hardcopy from the internet:

www.theautomationbookstore.com

• contact your local distributor or Rockwell Automation

representative to place an order.

See the table on the next page for other related publications.

Publication 1785-10.5 - November 1998

P-2 Preface

Related Documentation

The following documents contain additional information concerning

the products discussed in this manual.

Common Techniques Used in

This Manual

We use the following conventions throughout this manual:

• Bulleted lists provide information, not procedural steps.

• Numbered lists provide sequential steps or hierarchical

information.

We use this symbol to indicate additional references you can use

when you need more information about a particular topic.

For more information about: See this document: Publication number:

Ethernet programmable controllers Enhanced and Ethernet PLC-5 Programmable Controllers User Manual 1785-6.5.12

Universal 1771 I/O chassis Universal I/O Chassis Installation Instructions 1771-2.210

power supply Power Supply Modules (1771-P4S, -P6S, -P4S1, -P6S1)

Installation Instructions

1771-2.135

DH+® network

Enhanced and Ethernet PLC-5 Programmable Controllers User Manual 1785-6.5.12

Data Highway/Data Highway Plus/Data Highway II/Data Highway-485

Cable Installation Instructions

1770-6.2.2

communication cards 1784-KT

Communication Interface Card User Manual 1784-6.5.22

Allen-Bradley Publication Index (for your specific communication card) SD499

cables Enhanced and Ethernet PLC-5 Programmable Controllers User Manual 1785-6.5.12

batteries Allen-Bradley Guidelines for Lithium Battery Handling and Disposal AG-5.4

grounding and wiring Allen-Bradley

programmable controllers

Allen-Bradley Programmable Controller Wiring and Grounding Guidelines 1770-4.1

current Allen-Bradley documentation,

including ordering instructions

Allen-Bradley Publication Index SD499

terms and definitions Allen-Bradley Industrial Automation Glossary AG-7.1

Publication 1785-10.5 - November 1998

Preface P-3

Rockwell Automation Support Rockwell Automation offers support services worldwide, with over

75 sales/support offices, 512 authorized distributors, and 260

authorized systems integrators located throughout the United States

alone, plus Rockwell Automation representatives in every major

country in the world.

Local Product Support

Contact your local Rockwell Automation representative for:

• sales and order support

• product technical training

• warranty support

• support service agreements

Technical Product Assistance

If you need to contact Allen-Bradley for technical assistance, call

your local Allen-Bradley representative.

Your Questions or Comments about This Manual

If you discover a problem with this manual, please notify us of it

by completing and sending the enclosed Publication Problem Report

(at the back of this manual).

If you have any suggestions about how we can make this manual

more useful to you, please contact us at the address below:

Allen-Bradley Company, Inc.

Automation Group

Technical Communication

1 Allen-Bradley Drive

Mayfield Heights, OH 44124-6118

Telephone: (440) 646-5000

FAX: (440) 646-4320

Table of Contents

Publication 1785-10.5 - November 1998

Overview Chapter 1

What You Need to Do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Identifying the Processor’s Front Panel Components . . . . . . . . . . . . . . 1-2

Components You Need . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

Compliance to European Union Directives. . . . . . . . . . . . . . . . . . . . . . 1-4

EMC Directive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

Low Voltage Directive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

Set up the Hardware Chapter 2

Install the Hardware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Configure the I/O Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Ground the I/O Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Install the Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

Install the PLC-5 Processor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

Power Up the System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6

Install the I/O Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6

Connect the Personal Computer to the PLC-5 Processor . . . . . . . . . . . 2-6

Set up the Software Chapter 3

Install the Software and Set Up the Programming System . . . . . . . . . . 3-1

Start the Programming Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1

Power Up the System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

Troubleshoot the Processor

System

Chapter 4

Use the PLC-5 Processor

Status Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Troubleshoot General Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Troubleshoot the Processor Communication Channels. . . . . . . . . . . 4-2

Troubleshoot the Ethernet Status Indicators . . . . . . . . . . . . . . . . . . . 4-3

Specifications Appendix A

General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

Processor Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2

Battery Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3

Battery Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3

Average Battery Lifetime Specifications. . . . . . . . . . . . . . . . . . . . . A-3

Publication 1785-10.5 - November 1998

Chapter

Overview

This quick start is designed to provide you with the information you

need to get your system up and running quickly. Use this document if

you are knowledgeable about Ethernet PLC-5 products, but may not

have used one or more of them recently. The information we provide

is geared to “jog your memory”.

What You Need to Do If you need more information, see the Enhanced and Ethernet PLC-5

Programmable Controllers User Manual, publication number

1785-6.5.12 (see page P-1 for information about how to obtain a copy

of this manual).

Set up the Hardware

(Chapter 2)

Set up the Software

(Chapter 3)

Troubleshoot the

Processor System

(Chapter 4)

Data Highway

Plus

PLC-5/20E

Processor

Internal

Power Supply

PC with

Programming

Software

Publication 1785-10.5 - November 1998

1-2 Overview

Identifying the Processor’s Front

Panel Components

These pictures show the Enhanced PLC-5 processor front panel

components.

PLC-5/20E Processor Front Panel

PLC-5/20E

Programmable

Controller

battery indicator (red when the battery is low)

processor RUN/FAULT indicator (green when

running; red when faulted)

force indicator (amber when I/O forces

are enabled)

channel 0 communication status indicator

(green when the channel is communicating)

Install memory module here

Install battery here

PLC-5 family member designation

channel 1B communication port;

its default configuration is remote I/O scanner

channel 1B status indicator

(lights green and red)

Use this port with ASCII or DF1 full-duplex, half-duplex

master, and half-duplex slave protocols. The port’s

default configuration supports processor programming:

channel 0*25-pin D-shell serial port; supports standard

EIA RS-232C and RS-423 and is RS-422A compatible

one stop-bit

BCC error check

no handshaking

DF1 point-to-point

2400 bps

no parity

keyswitch; selects processor mode

channel 1A communication port; its default

configuration is DH+ communication

8-pin mini-DIN, DH+ programming terminal

connection parallel to channel 1A

channel 2 Ethernet status indicator (green when

functioning normally; red when not functioning)

channel 2 communication port;

a 15-pin Ethernet port

channel 2, Ethernet transmit indicator

(green when the channel is communicating)

channel 1A status indicator

(lights green and red)

Publication 1785-10.5 - November 1998

Overview 1-3

PLC-5/20E Processor Front Panel

PLC-5/40E

Programmable

Controller

Use this port with ASCII or DF1 full-duplex, half-duplex

master, and half-duplex slave protocols. The port’s

default configuration supports processor programming:

channel 0-25-pin D-shell serial port; supports standard

EIA RS-232C and RS-423 and is RS-422A compatible

one stop-bit

BCC error check

no handshaking

DF1 point-to-point

2400 bps

no parity

battery indicator (red when the battery is low)

processor RUN/FAULT indicator (green when

running; red when faulted)

force indicator (amber when I/O forces

are enabled)

channel 0 communication status indicator

(green when the channel is communicating)

Install memory module here

Use these labels to write information about the

channel: communication mode, station addresses etc.

Install battery here

channel 1B status indicator (lights green and red)

PLC-5 family member designation

keyswitch; selects processor mode

channel 1A communication port; its default

configuration is DH+ communication

8-pin mini-DIN, DH+ programming terminal

connection parallel to channel 1A

channel 2 Ethernet status indicator (green when

functioning normally; red when not functioning)

channel 2 communication port;

a 15-pin Ethernet port

channel 1A status indicator

(lights green and red)

channel 2, Ethernet transmit indicator (green when

the channel is communicating)

channel 1B communication port; its default

configuration is remote I/O scanner

Wrist strap

ATTENTION: Make sure you understand the anti-static environment.

The processor is shipped in a static-shielded container to guard against

electrostatic damage. Electrostatic discharge can damage integrated

circuits or semiconductors in the processor module if you touch

backplane connector pins. It can also damage the module when you set

configuration plugs or switches inside the module. Avoid electrostatic

damage by observing the following precautions.

• Remain in contact with an approved ground point while handling the

module (by wearing a properly grounded wrist strap).

• Do not touch the backplane connector or connector pins.

• When not in use, keep the module in its static-shielded container.

Publication 1785-10.5 - November 1998

1-4 Overview

Components You Need

Important: In this manual, we assume you are using a brand-new

Enhanced PLC-5 processor out of the box.

Compliance to

European Union Directives

If this product has the CE mark it is approved for installation within

the European Union and EEA regions. It has been designed and tested

to meet the following directives.

EMC Directive

This product is tested to meet Council Directive 89/336/EEC

Electromagnetic Compatibility (EMC) and the following standards,

in whole or in part, documented in a technical construction file:

• EN 50081-2EMC – Generic Emission Standard, Part 2 –

Industrial Environment

• EN 50082-2EMC – Generic Immunity Standard, Part 2 –

Industrial Environment

This product is intended for use in an industrial environment.

Low Voltage Directive

This product is tested to meet Council Directive 73/23/EEC Low

Voltage, by applying the safety requirements of EN 61131-2

Programmable Controllers, Part 2 – Equipment Requirements and

Tests.

For specific information required by EN 61131-2, see the appropriate

sections in this publication, as well as the following Allen-Bradley

publications:

• Industrial Automation Wiring and Grounding Guidelines For

Noise Immunity, publication 1770-4.1

• Guidelines for Handling Lithium Batteries, publication AG-5.4

• Automation Systems Catalog

Product name: Catalog number:

Hardware

Ethernet PLC-5 processor

with 2 keys

1785-L20E, -L40E, -L80E

Lithium Battery

(in a clear bag)

1770-XYC

I/O chassis 1771-A1B, -A2B, -A3B, -A3B1, -A4B

Power supply 1771-P4S, -P6S, -P4S1, -P6S1

Programming System

PC Check your programming software documentation for

system requirements, such as memory, etc.

PLC-5 programming

software

Choose a programming software package that is

compatible with Ethernet PLC-5 processors.

communication module Ethernet interface and interconnect cable

Publication 1785-10.5 - November 1998

Chapter

Set up the Hardware

For more information, see the Enhanced and Ethernet User Manual,

publication number 1785-6.5.12.

Data Highway

Plus or serial

cable

PLC-5/20E

Processor

Internal

Power Supply

PC with

Programming

Software

Install the hardware

(page 2-2)

Connect the programming terminal

and the PLC-5 processor to the

communication card

(page 2-6)

Install the hardware

(page 2-2)

Connect the programming terminal

and the PLC-5 processor to the

communication card

(page 2-6)

Publication 1785-10.5 - November 1998

2-2 Set up the Hardware

Install the Hardware Configure the I/O Chassis

Regardless of this switch setting, outputs are turned off when any of the following occurs:

- processor detects a runtime error

- an I/O chassis backplane fault occurs

- you select program or test mode

- you set a status file bit to reset a local rack

` If an EEPROM module is not installed and processor memory is valid, the processor's PROC LED indicator blinks,

and the processor sets S:11/9, bit 9 in the major fault status word. To clear this fault, change the processor from

program mode to run mode and back to program mode.

´ If the processor's keyswitch is set in REMote, the processor enters remote RUN after it powers up and has its

memory updated by the EEPROM module.

ˆ A processor fault (solid red PROC LED) occurs if processor memory is not valid.

˜ You cannot clear processor memory when this switch is on.

2 - slot

1 - slot

1/2 - slot

Always

Off

19309

Outputs of this I/O chassis remain in their last state when

a hardware failure occurs.

Outputs of this I/O chassis are turned off when a

hardware failure occurs.

EEPROM memory transfer to processor memory at power-up. ` ´

EEPROM memory transfers to processor memory if processor memory

not valid.

EEPROM memory does not transfer to processor memory. ˆ

Processor memory protection disabled.

Processor memory protection enabled. ˜

Not allowed

Processor Memory Protection

Switch

off

EEPROM Transfer

Addressing

Last State

Switch

off

Switches

off off

off on

on off

on on

off off

on on

on off

Set the backplane switches.

Pressed in

at top ON (closed)

Pressed in

at bottom OFF (open)

12345678

2, 3

Publication 1785-10.5 - November 1998

Set up the Hardware 2-3

For more information, see the Universal I/O Chassis installation

instructions, publication number 1771-2.10.

Ground the I/O Chassis

For more information, see the Allen-Bradley Programmable

Controller Wiring and Grounding Guidelines, publication number

1770-4.1.

20609-M

Keying

Bands

Set the power supply

configuration jumper.

Install the keying bands.

Are you using a power

supply module in

the chassis?

between

- 40 & 42

- 54 & 56

PLC-5/20

Processor

1 2345678

Ground Lug

Star

Washer

Nut and

Captive Washer

I/O Chassis Wall

Grounding Electrode

Conductor

Ground

Bus

To Grounding

Electrode System

Enclosure

20626-M

Publication 1785-10.5 - November 1998

2-4 Set up the Hardware

Install the Power Supply

For more information, see the Power Supply Modules

(1771-P4S, -P6S, -P4S1, -P6S1) Installation Instructions, publication

number 1771-2.135 or the AC (120/220V) 16A Power Supply

(1771-P7 Series B/C) Installation Instructions, publication

number 1771-5.39.

Locking

Bar

20619-M

Set the jumpers on

the back side of the

power supply like this:

Connect the power cord to the 120V ac

connector of the power supply module.

Install the power supply in the chassis

and snap the module-locking bar over

the modules

This side plugs into connector on the module.

insert wire

here

place tool here

insert wire

here

place tool here

Publication 1785-10.5 - November 1998

Set up the Hardware 2-5

Install the PLC-5 Processor

Define the DH+ Station Address of Channel 1A

by setting switch assembly SW-1.

1 2

Specify the serial communication of channel 0.

Front of

Processor

Front of

Processor

Bottom view of PLC-5/20E processor switch assembly SW2

Bottom view of PLC-5/40E and -5/80E

processor switch assembly SW2

side view

OFF

Always off

Side View of PLC-5/20E processors SW1

Side View of PLC-5/40E and -5/80E processors SW1

ENET 802.3

Hardware

Ethernet

address label

Ethernet

configuration

jumper

Install the processor module.

To install the battery, slide the battery-side connector into the

processor-side connector until you hear them snap together, and

attach the battery cover.

Identify the Ethernet configuration jumper and

hardware Ethernet address.

IMPORTANT: Do not change the Etherrnet configuration

jumper default setting, which is set at 802.3.

Most Ethernet networks use the 802.3 standard; however

if your Ethernet network is an older network and complies

with the original Ethernet standard, then set the jumper

to ENET.

The hardware Ethernet address label is located to the

right of the Ethernet configuration jumper and shows the

hardware Ethernet address assigned by Allen-Bradley.

For detailed information about handling and disposing

of the battery as well as other important guidelines, see

publication AG-5.4.

ATTENTION: To maintain CSA certification for hazardous

areas, do not substitute any other battery for the 1770-XYC.

For series E and later processors:

use this switch to select baud rate

For series D and earlier processors:

this switch is always off

side view

230 Kbaud

down

57.6 Kbaud

Locking

Bar

PLC-5/20E

Processor

Card Guides

Lift Eector Tab

20897-M

Battery Connector

Battery

Battery Cover

1234567

123456789

Publication 1785-10.5 - November 1998

2-6 Set up the Hardware

Power Up the System

Power up the system. Check the LED display on the processor. If

your system is operating properly, the PROC LED should be steady

red. If the PROC LED is not red, see chapter 4 for troubleshooting

information before you install any I/O modules.

Install the I/O Modules

For more information, see the installation instructions or user manual

for the particular module you are installing.

Connect the Personal

Computer to the

PLC-5 Processor

For more information, see:

• Enhanced and Ethernet PLC-5 Programmable Controller User

Manual, publication number 1785-6.5.12

• the documentation provided with your communication card

• Data Highway/Data Highway Plus/Data Highway II/Data

Highway 485 Cable Installation Manual, publication 1770-6.2.2

Locking

Bar

Card Guides

20618-M

Install each I/O module and connect

the wiring arm.

Publication 1785-10.5 - November 1998

Chapter

Set up the Software

The following instructions are general. For specific information, see

the documentation set for your particular software package.

Install the Software and Set

Up the Programming System

Before you install your programming software, make certain you

meet the system requirements for that software – sufficient disk

space, memory, etcetera. Then, follow the procedures outlined in the

software documentation to install the software and configure

communication.

Start the

Programming Software

Start the programming software by following the procedures

described in your programming software documentation.

If you have difficulty, verify that the power supply is turned on.

To monitor your system as you configure and run it, check the

processor LED display for the following indicators:

Powerup the system

Install the software

Start the programming software

This LED: lights when:

COMM you establish DH+ communication

BATT no battery is installed or the battery voltage is low

REM I/O you establish Remote I/O communication

ADAPT the processor is in adapter mode

FORCE forces are present in your ladder program

Publication 1785-10.5 - November 1998

3-2 Set up the Software

Power Up the System Power up the system if you have not done so already. Check the LED

display on the processor. If your system is operating properly, the

PROC LED should be steady red and the message

“Processor RAM

is faulted. Press <Enter> to clear memory” should appear on

the display. See the following table to proceed. If the PROC LED is

not red, turn to chapter 4 for troubleshooting information.

If your keyswitch

is in this position:

do this:

PROGRAM Clear memory. The PROC LED should turn off.

The software is in Program mode.

REMOTE Clear memory. The PROC LED should turn off.

The software is in Remote Program mode.

RUN You see the message “No access or

privilege violation” because you cannot

clear memory in Run mode. Change the keyswitch

position to Program or Remote and press <Enter> to

clear memory.

Publication 1785-10.5 - November 1998

Chapter

Troubleshoot the Processor System

Use the PLC-5 Processor

Status Indicators

Troubleshoot General Problems

Use the PLC-5 Processor

Status Indicators

(page 4-1)

BATT

PROC

FORCE

COMM

Indicator Color Description Probable Cause Recommended Action

BATT Red Battery low Battery low Replace battery within 10 days

Off Battery is good Normal operation No action required

PROC Green

(steady)

Processor is in run

mode and fully

operational

Normal operation No action required

Green

(blinking)

Processor memory is

being transferred to

EEPROM

Red

(blinking)

Major fault Run-time error • Check major fault bit in status file

(S:11) for error definition

• Clear fault bit, correct problem,

and return to run mode

Red

(steady)

Major fault • Processor memory

has checksum

error

• Memory module

error

• Internal

diagnostics have

failed

• Clear memory and reload program

• Check backplane switch settings

and/or insert correct memory

module

• Power down, reseat processor

and power up; then, clear

memory and reload your program.

Replace EEPROM with new

program; then, if necessary,

replace the processor

Off Processor is in

program load or test

mode or is not

receiving power

Check power supply and

connections

BATT

PROC

FORCE

COMM

Publication 1785-10.5 - November 1998

4-2 Troubleshoot the Processor System

Troubleshoot the Processor Communication Channels

FORCE Amber

(steady)

SFC and/or I/O forces

enabled

Normal operation No action required

Amber

(blinking)

SFC and/or I/O forces

present but not

enabled

Off SFC and/or I/O forces

not present

COMM Off No transmission on

channel 0

Normal operation if

channel is not being

used

Green

(blinking)

Transmission on

channel 0

Normal operation if

channel is being used

Indicator Color Description Probable Cause Recommended Action

Indicator Color Channel Mode Description Probable Cause Recommended Action

A or B Green

(steady)

Remote I/O Scanner Active Remote I/O link, all

adapter modules are present

and not faulted

Normal operation No action required

Remote I/O Adapter Communicating with scanner

DH+ Processor is transmitting or

receiving on DH+ link

Green

(blinking

rapidly or

slowly)

Remote I/O Scanner At least one adapter is

faulted or has failed

• Power off at

remote rack

• Cable broken

• Restore power to the

rack

• Repair cable

DH+ No other nodes on network

Red

(steady)

Remote I/O Scanner

Remote I/O Adapter

DH+

Hardware fault Hardware error • Turn power off, then

on.

• Check that the

software

configurations match

the hardware set-up.

• Replace the processor.

Red

(blinking

rapidly or

slowly)

Remote I/O Scanner Faulted adapters detected • Cable not

connected or is

broken

• Power off at

remote racks

• Repair cable

• Restore power to racks

DH+ Bad communication on DH+ Duplicate node

detected

Correct station address

Off Remote I/O Scanner

Remote I/O Adapter

DH+

Channel offline Channel is not

being used

Place channel online if

needed

La page est en cours de chargement...

Rockwell Automation 1785-L80E Manuel utilisateur

Marque: Rockwell Automation

Modèle: 1785-L80E

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Rockwell Automation 1785-L80E User manual

Rockwell Automation 1785-L80E Manuel utilisateur

Ce manuel convient également à

Rockwell Automation 1785-L80E Manuel utilisateur

dans d''autres langues

Autres documents