DeWalt DCS380B Le manuel du propriétaire

Marque: DeWalt

Modèle: DCS380B

Taper: Le manuel du propriétaire

Ce manuel convient également à

DCS380B 20V MAX Lithium-Ion Variable Speed Cordless

DCS380, DCS381

20V Max* Cordless Reciprocating Saws

Scies alternatives sans fil DCS380, DCS381 de 20 V Max*

Sierras alternativas inalámbricas de 20 V Máx*

DCS380, DCS381

INSTRUCTION MANUAL

GUIDE D’UTILISATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE

GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE

USAR EL PRODUCTO.

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-DEWALT • www.dewalt.com

English

Deﬁ nitions: Safety Guidelines

The definitions below describe the level of severity for each

signal word. Please read the manual and pay attention to these

symbols.

DANGER: Indicates an imminently hazardous situation

which, if not avoided, will result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which,

if not avoided, could result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which,

if not avoided, may result in minor or moderate injury.

NOTICE: Indicates a practice not related to personal injury

which, if not avoided, may result in property damage.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR

ANY D

EWALT TOOL, CALL US TOLL FREE AT: 1-800-4-DEWALT

(1-800-433-9258).

WARNING: To reduce the risk of injury, read the instruction

manual.

General Power Tool Safety Warnings

WARNING! Read all safety warnings and all instructions.

Failure to follow the warnings and instructions may result in

electric shock, fire and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

The term “power tool” in the warnings refers to your mains-operated

(corded) power tool or battery-operated (cordless) power tool.

1) WORK AREA SAFETY

a) Keep work area clean and well lit. Cluttered or dark areas

invite accidents.

b) Do not operate power tools in explosive atmospheres,

such as in the presence of flammable liquids, gases or

dust. Power tools create sparks which may ignite the dust or

fumes.

c) Keep children and bystanders away while operating a

power tool. Distractions can cause you to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet. Never modify

the plug in any way. Do not use any adapter plugs with

earthed (grounded) power tools. Unmodified plugs and

matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces

such as pipes, radiators, ranges and refrigerators. There

is an increased risk of electric shock if your body is earthed or

grounded.

c) Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of electric

shock.

d) Do not abuse the cord. Never use the cord for carrying,

pulling or unplugging the power tool. Keep cord away

from heat, oil, sharp edges or moving parts. Damaged or

entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension

cord suitable for outdoor use. Use of a cord suitable for

outdoor use reduces the risk of electric shock.

f) If operating a power tool in a damp location is unavoidable,

use a ground fault circuit interrupter (GFCI) protected

supply. Use of a GFCI reduces the risk of electric shock.

English

b) Do not use the power tool if the switch does not turn it

on and off. Any power tool that cannot be controlled with the

switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the

battery pack from the power tool before making any

adjustments, changing accessories, or storing power

tools. Such preventive safety measures reduce the risk of

starting the power tool accidentally.

d) Store idle power tools out of the reach of children and do

not allow persons unfamiliar with the power tool or these

instructions to operate the power tool. Power tools are

dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding

of moving parts, breakage of parts and any other condition

that may affect the power tool’s operation. If damaged,

have the power tool repaired before use. Many accidents

are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly maintained

cutting tools with sharp cutting edges are less likely to bind and

are easier to control.

g) Use the power tool, accessories and tool bits, etc. in

accordance with these instructions, taking into account

the working conditions and the work to be performed.

Use of the power tool for operations different from those

intended could result in a hazardous situation.

5) BATTERY TOOL USE AND CARE

a) Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type of

battery pack may create a risk of fire when used with another

battery pack.

b) Use power tools only with specifically designated battery

packs. Use of any other battery packs may create a risk of

injury and fire.

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and use common

sense when operating a power tool. Do not use a power

tool while you are tired or under the influence of drugs,

alcohol or medication. A moment of inattention while

operating power tools may result in serious personal injury.

b) Use personal protective equipment. Always wear eye

protection. Protective equipment such as dust mask, non-

skid safety shoes, hard hat, or hearing protection used for

appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in

the off position before connecting to power source and/

or battery pack, picking up or carrying the tool. Carrying

power tools with your finger on the switch or energizing power

tools that have the switch on invites accidents.

d) Remove any adjusting key or wrench before turning the

power tool on. A wrench or a key left attached to a rotating

part of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at

all times. This enables better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose clothing or jewelry.

Keep your hair, clothing and gloves away from moving

parts. Loose clothes, jewelry or long hair can be caught in

moving parts.

g) If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection can

reduce dust-related hazards.

4) POWER TOOL USE AND CARE

a) Do not force the power tool. Use the correct power tool

for your application. The correct power tool will do the job

better and safer at the rate for which it was designed.

English

• Use extra caution when cutting overhead and pay particular

attention to overhead wires which may be hidden from view.

Anticipate the path of falling branches and debris ahead of time.

• Do not operate this tool for long periods of time. Vibration

caused by the operating action of this tool may cause permanent

injury to fingers, hands, and arms. Use gloves to provide extra

cushion, take frequent rest periods, and limit daily time of use.

WARNING: ALWAYS use safety glasses. Everyday eyeglasses are

NOT safety glasses. Also use face or dust mask if cutting operation

is dusty. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratory protection.

WARNING: Some dust created by power sanding, sawing,

grinding, drilling, and other construction activities contains chemicals

known to the State of California to cause cancer, birth defects or

other reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry

products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you

do this type of work. To reduce your exposure to these chemicals:

work in a well ventilated area, and work with approved safety

equipment, such as those dust masks that are specially designed to

filter out microscopic particles.

• Avoid prolonged contact with dust from power sanding,

sawing, grinding, drilling, and other construction activities.

Wear protective clothing and wash exposed areas with soap

and water. Allowing dust to get into your mouth, eyes, or lay on

the skin may promote absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disperse dust,

which may cause serious and permanent respiratory or other injury.

c) When battery pack is not in use, keep it away from other

metal objects like paper clips, coins, keys, nails, screws,

or other small metal objects that can make a connection

from one terminal to another. Shorting the battery terminals

together may cause burns or a fire.

d) Under abusive conditions, liquid may be ejected from

the battery; avoid contact. If contact accidentally occurs,

flush with water. If liquid contacts eyes, additionally seek

medical help. Liquid ejected from the battery may cause

irritation or burns.

6) SERVICE

a) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained.

Additional Speciﬁ c Safety Rules for

Reciprocating Saws

• Hold power tool by insulated gripping surfaces, when

performing an operation where the cutting accessory may

contact hidden wiring. Cutting accessory contacting a “live”

wire may make exposed metal parts of the power tool “live” and

could give the operator an electric shock.

• Use clamps or another practical way to secure and support

the workpiece to a stable platform. Holding the work by hand

or against your body leaves it unstable and may lead to loss

of control.

• Hold saw firmly with both hands for all cutting operations.

During cutting operations, the blade may suddenly bind in the work

and may cause the saw to kickback towards the operator.

• Keep hands away from moving parts. Never place your hands

near the cutting area.

English

Important Safety Instructions for All

Battery Packs

When ordering replacement battery packs, be sure to include the

catalog number and voltage. Consult the chart at the end of this

manual for compatibility of chargers and battery packs.

The battery pack is not fully charged out of the carton. Before using

the battery pack and charger, read the safety instructions below and

then follow charging procedures outlined.

READ ALL INSTRUCTIONS

• Do not charge or use the battery pack in explosive

atmospheres, such as in the presence of flammable liquids,

gases or dust. Inserting or removing the battery pack from the

charger may ignite the dust or fumes.

• NEVER force the battery pack into the charger. Do not

modify the battery pack in any way to fit into a non-

compatible charger as battery pack may rupture causing

serious personal injury. Consult the chart at the end of this

manual for compatibility of batteries and chargers.

• Charge the battery packs only in designated D

EWALT chargers.

• DO NOT splash or immerse in water or other liquids.

• Do not store or use the tool and battery pack in locations

where the temperature may reach or exceed 105°F (40°C)

(such as outside sheds or metal buildings in summer). For

best life store battery packs in a cool, dry location.

NOTE: Do not store the battery packs in a tool with the

trigger switch locked on. Never tape the trigger switch in the

ON position.

WARNING: Fire hazard. Never attempt to open the battery pack

for any reason. If the battery pack case is cracked or damaged, do

not insert into the charger. Do not crush, drop or damage the battery

pack. Do not use a battery pack or charger that has received a sharp

Always use NIOSH/OSHA approved respiratory protection

appropriate for the dust exposure. Direct particles away from face

and body.

WARNING: Always wear proper personal hearing protection

that conforms to ANSI S12.6 (S3.19) during use. Under some

conditions and duration of use, noise from this product may

contribute to hearing loss.

CAUTION: When not in use, place tool on its side on a stable

surface where it will not cause a tripping or falling hazard.

Some tools with large battery packs will stand upright on the battery

pack but may be easily knocked over.

• The label on your tool may include the following symbols. The

symbols and their definitions are as follows:

V ................... volts A ......................amperes

Hz ................. hertz W .....................watts

min ............... minutes

or AC ..........alternating

or DC ...direct current current

................. Class I Construction or AC/DC ...alternating

.....................

(grounded) ........................or direct

................. Class II Construction current

(double insulated)

o ....................no load

…/min .......... per minute speed

BPM ............. beats per minute

n ......................rated

IPM ............... impacts per minute

........................speed

RPM ............. revolutions per

.....................earthing

minute terminal

sfpm ............. surface feet

..................... safety alert

..................... per minute symbol

SPM ............. strokes per minute

English

The RBRC™ Seal

The RBRC™ (Rechargeable Battery Recycling Corp oration) Seal on the

nickel cadmium, nickel metal hydride or lithium ion

batteries (or battery packs) indicate that the costs to

recycle these batteries (or battery packs) at the end of

their useful life have already been paid by D

EWALT. In

some areas, it is illegal to place spent nickel cadmium,

nickel metal hydride or lithium ion batteries in the trash

or municipal solid waste stream and the RBRC program provides an

environmentally conscious alternative.

RBRC™, in cooperation with D

EWALT and other battery users, has

established programs in the United States and Canada to facilitate

the collection of spent nickel cadmium, nickel metal hydride or lithium

ion batteries. Help protect our environment and conserve natural

resources by returning the spent nickel cadmium, nickel metal hydride

or lithium ion batteries to an authorized D

EWALT service center or

to your local retailer for recycling. You may also contact your local

recycling center for information on where to drop off the spent battery.

RBRC™ is a registered trademark of the Rechargeable Battery

Recycling Corporation.

Important Safety Instructions for All

Battery Chargers

SAVE THESE INSTRUCTIONS: This manual contains important

safety and operating instructions for battery chargers.

• Before using the charger, read all instructions and cautionary

markings on the charger, battery pack and product using the

battery pack.

WARNING: Shock hazard. Do not allow any liquid to get inside the

charger. Electric shock may result.

CAUTION: Burn hazard. To reduce the risk of injury, charge only

EWALT rechargeable battery packs. Other types of batteries may

overheat and burst resulting in personal injury and property damage.

blow, been dropped, run over or damaged in any way (e.g., pierced

with a nail, hit with a hammer, stepped on). Damaged battery packs

should be returned to the service center for recycling.

WARNING: Fire hazard. Do not store or carry the battery

pack so that metal objects can contact exposed battery

terminals. For example, do not place the battery pack in aprons,

pockets, tool boxes, product kit boxes, drawers, etc., with loose

nails, screws, keys, etc. Transporting batteries can possibly

cause fires if the battery terminals inadvertently come in

contact with conductive materials such as keys, coins, hand

tools and the like. The US Department of Transportation Hazardous

Material Regulations (HMR) actually prohibit transporting batteries in

commerce or on airplanes (e.g., packed in suitcases and carry-on

luggage) UNLESS they are properly protected from short circuits.

So when transporting individual battery packs, make sure that the

battery terminals are protected and well insulated from materials that

could contact them and cause a short circuit.

SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION (Li-Ion)

• Do not incinerate the battery pack even if it is severely

damaged or is completely worn out. The battery pack can

explode in a fire. Toxic fumes and materials are created when

lithium ion battery packs are burned.

• If battery contents come into contact with the skin,

immediately wash area with mild soap and water. If battery

liquid gets into the eye, rinse water over the open eye for 15

minutes or until irritation ceases. If medical attention is needed,

the battery electrolyte is composed of a mixture of liquid organic

carbonates and lithium salts.

• Contents of opened battery cells may cause respiratory

irritation. Provide fresh air. If symptoms persist, seek medical

attention.

WARNING: Burn hazard. Battery liquid may be flammable if

exposed to spark or flame.

English

total length, be sure each individual extension contains at least the

minimum wire size. The following table shows the correct size to

use depending on cord length and nameplate ampere rating. If in

doubt, use the next heavier gauge. The lower the gauge number,

the heavier the cord.

Minimum Gauge for Cord Sets

Ampere

Rating

Volts Total Length of Cord

in Feet (meters)

120 V 25

(7.6)

(15.2)

100

(30.5)

150

(45.7)

240 V 50

(15.2)

100

(30.5)

200

(61.0)

300

(91.4)

Than

Not

Than

AWG

0 6 18 16 16 14

610 1816 14 12

10 12 16 16 14 12

12 16 14 12 Not Recommended

• Do not place any object on top of the charger or place the

charger on a soft surface that might block the ventilation

slots and result in excessive internal heat. Place the charger

in a position away from any heat source. The charger is ventilated

through slots in the top and the bottom of the housing.

• Do not operate the charger with a damaged cord or plug.

• Do not operate the charger if it has received a sharp blow,

been dropped or otherwise damaged in any way. Take it to an

authorized service center.

• Do not disassemble the charger; take it to an authorized

service center when service or repair is required. Incorrect

reassembly may result in a risk of electric shock, electrocution or fire.

NOTICE: Under certain conditions, with the charger plugged into the

power supply, the charger can be shorted by foreign material. Foreign

materials of a conductive nature, such as, but not limited to, grinding

dust, metal chips, steel wool, aluminum foil or any buildup of metallic

particles should be kept away from the charger cavities. Always unplug

the charger from the power supply when there is no battery pack in the

cavity. Unplug the charger before attempting to clean.

• DO NOT attempt to charge the battery pack with any

chargers other than the ones in this manual. The charger and

battery pack are specifically designed to work together.

• These chargers are not intended for any uses other than

charging D

EWALT rechargeable batteries. Any other uses may

result in risk of fire, electric shock or electrocution.

• Do not expose the charger to rain or snow.

• Pull by the plug rather than the cord when disconnecting

the charger. This will reduce the risk of damage to the electric plug

and cord.

• Make sure that the cord is located so that it will not be

stepped on, tripped over or otherwise subjected to damage

or stress.

• Do not use an extension cord unless it is absolutely

necessary. Use of improper extension cord could result in risk of

fire, electric shock or electrocution.

• When operating a charger outdoors, always provide a dry

location and use an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces the risk of electric

shock.

• An extension cord must have adequate wire size (AWG

or American Wire Gauge) for safety. The smaller the gauge

number of the wire, the greater the capacity of the cable, that is,

16 gauge has more capacity than 18 gauge. An undersized cord

will cause a drop in line voltage resulting in loss of power and

overheating. When using more than one extension to make up the

English

Indicator Light Operation

DCB101

PACK CHARGING

PACK CHARGED

HOT/COLD DELAY

PROBLEM PACK OR CHARGER

PROBLEM POWERLINE

DCB107, DCB112

PACK CHARGING

PACK CHARGED

HOT/COLD DELAY

Charge Indicators

This charger is designed to detect certain problems that can arise.

Problems are indicated by the red light flashing at a fast rate. If this

occurs, re-insert the battery pack into the charger. If the problem

persists, try a different battery pack to determine if the charger is

working properly. If the new pack charges correctly, then the original

pack is defective and should be returned to a service center or other

collection site for recycling. If the new battery pack elicits the same

trouble indication as the original, have the charger and the battery pack

tested at an authorized service center.

• Disconnect the charger from the outlet before attempting

any cleaning. This will reduce the risk of electric shock.

Removing the battery pack will not reduce this risk.

• NEVER attempt to connect 2 chargers together.

• The charger is designed to operate on standard 120V

household electrical power. Do not attempt to use it on any

other voltage. This does not apply to the vehicular charger.

Chargers

Your tool uses a DEWALT charger. Be sure to read all safety instructions

before using your charger. Consult the chart at the end of this manual

for compatibility of chargers and battery packs.

Charging Procedure (Fig. 1)

1. Plug the charger into an appropriate

DCB101

FIG. 1

outlet before inserting the battery

pack.

2. Insert the battery pack (F) into the

charger, as shown in Figure 1,

making sure the pack is fully seated

in charger. The red (charging) light

will blink continuously, indicating

that the charging process has

started.

3. The completion of charge will be

indicated by the red light remaining

ON continuously. The pack is fully

charged and may be used at this

time or left in the charger.

English

sources that convert DC to AC, the charger may temporarily suspend

operation, flashing the red light with two fast blinks followed by a pause.

This indicates the power source is out of limits.

Wall Mounting

DCB107, DCB112

These chargers are designed to be wall mountable or to sit upright on

a table or work surface.

If wall mounting, locate the charger within reach of an electrical outlet.

Mount the charger securely using drywall screws at least 1" (25.4 mm)

long, screwed into wood to an optimal depth leaving approximately

7/32" (5.5 mm) of the screw exposed.

Important Charging Notes

1. Longest life and best performance can be obtained if the battery

pack is charged when the air temperature is between 65°F and

75°F (18° – 24°C). DO NOT charge the battery pack in an air

temperature below +40°F (+4.5°C), or above +105°F (+40.5°C).

This is important and will prevent serious damage to the battery

pack.

2. The charger and battery pack may become warm to the touch

while charging. This is a normal condition, and does not indicate

a problem. To facilitate the cooling of the battery pack after use,

avoid placing the charger or battery pack in a warm environment

such as in a metal shed or an uninsulated trailer.

3. A cold battery pack will charge at about half the rate of a warm

battery pack. The battery pack will charge at that slower rate

throughout the entire charging cycle and will not return to

maximum charge rate even if the battery pack warms.

4. If the battery pack does not charge properly:

a. Check operation of receptacle by plugging in a lamp or other

appliance;

HOT/COLD DELAY

DCB101

This charger has a hot/cold delay feature: when the charger detects a

battery that is hot, it automatically starts a delay, suspending charging

until the battery has cooled. After the battery has cooled, the charger

automatically switches to the pack charging mode. This feature

ensures maximum battery life. The red light flashes long, then short

while in the hot/cold delay mode.

DCB107, DCB112

The DCB107 and DCB112 chargers have a hot/cold delay feature.

When the charger detects a battery that is hot, it automatically delays

charging until the battery has cooled. When the charger detects a

battery that is cold, it automatically delays charging until the battery

has warmed.

The red light will continue to blink, but a yellow indicator light will

be illuminated during this operation. Once the battery has cooled,

the yellow light will turn off and the charger will resume the charging

procedure.

LEAVING THE BATTERY PACK IN THE CHARGER

The charger and battery pack can be left connected with the charge

indicator showing Pack Charged.

WEAK BATTERY PACKS: Weak batteries will continue to function

but should not be expected to perform as much work.

FAULTY BATTERY PACKS: This charger will not charge a faulty

battery pack. The charger will indicate faulty battery pack by refusing

to light or by displaying problem pack or charger.

NOTE: This could also mean a problem with a charger.

PROBLEM POWER LINE (DCB101)

Some chargers have a problem powerline indicator. When the charger

is used with some portable power sources such as generators or

English

NOTE: Battery packs should not be stored completely depleted of

charge. The battery pack will need to be recharged before use.

SAVE THESE INSTRUCTIONS

FOR FUTURE USE

FIG. 2

DCS380

DCS381

b. Check to see if receptacle is connected to a light switch which

turns power off when you turn out the lights;

c. Move the charger and battery pack to a location where the

surrounding air temperature is approximately 65 °F – 75 °F

(18° – 24°C);

d. If charging problems persist, take the tool, battery pack and

charger to your local service center.

5. The battery pack should be recharged when it fails to produce

sufficient power on jobs which were easily done previously. DO

NOT CONTINUE to use under these conditions. Follow the

charging procedure. You may also charge a partially used pack

whenever you desire with no adverse effect on the battery pack.

6. Foreign materials of a conductive nature such as, but not limited

to, grinding dust, metal chips, steel wool, aluminum foil, or any

buildup of metallic particles should be kept away from charger

cavities. Always unplug the charger from the power supply when

there is no battery pack in the cavity. Unplug the charger before

attempting to clean.

7. Do not freeze or immerse the charger in water or any other liquid.

WARNING: Shock hazard. Don’t allow any liquid to get inside the

charger. Electric shock may result.

WARNING: Burn hazard. Do not submerge the battery pack in

any liquid or allow any liquid to enter the battery pack. Never attempt

to open the battery pack for any reason. If the plastic housing of the

battery pack breaks or cracks, return to a service center for recycling.

Storage Recommendations

1. The best storage place is one that is cool and dry, away from direct

sunlight and excess heat or cold.

2. For long storage, it is recommended to store a fully charged

battery pack in a cool dry place out of the charger for optimal

results.

English

CAUTION: Use of very slow speed is recommended only for

beginning a cut. Prolonged use at very slow speed may damage your

saw.

OPERATION

WARNING: To reduce the risk of serious personal injury,

turn tool off and disconnect tool from power source before

making any adjustments or removing/installing attachments or

accessories. An accidental start-up can cause injury.

Installing and Removing the Battery Pack

(Fig. 4)

WARNING: To reduce the

FIG. 4

risk of injury, never depress the

battery release button without

removing the battery pack.

Depressing the battery release

button without removing the

battery pack can result in the

battery pack falling out

unexpectedly.

NOTE: For best results, make

sure your battery pack is fully

charged.

To install the battery pack (F) into the tool handle, align the battery pack

with the rails inside the tool’s handle and slide it into the handle until

the battery pack is firmly seated in the tool and ensure that it does not

disengage.

To remove the battery pack from the tool, press the release button (G)

and firmly pull the battery pack out of the tool handle. Insert it into the

charger as described in the charger section of this manual.

COMPONENTS (Fig. 2)

WARNING: Never modify the power tool or any part of it. Damage

or personal injury could result.

A. Trigger switch E. Hand grip

B. Lock-off button F. Battery pack

C. Blade clamp release lever G. Battery release button

D. Shoe

Variable Speed Trigger Switch (Fig. 2, 3)

LOCK-OFF BUTTON AND TRIGGER SWITCH

Your saw is equipped with a lock-off button (B).

To lock the trigger switch, press

FIG. 3

UNLOCKED

LOCKED

the lock-off button as shown in

Figure 3. Always lock the trigger

switch (A) when carrying or storing

the tool to eliminate unintentional

starting. The lock-off button is

colored red to indicate when the

switch is in its unlocked position.

To unlock the trigger switch,

press the lock-off button as shown

in Figure 3. Pull the trigger switch

to turn the motor ON. Releasing

the trigger switch turns the motor

OFF.

WARNING: This tool has no provision to lock the switch in the ON

position, and should never be locked ON by any other means.

The variable speed trigger switch will give you added versatility. The

further the trigger is depressed the higher the speed of the saw.

English

WARNING: Cut hazard. Blade breakage may occur if the blade

does not extend past the shoe and the workpiece during the cut

(Fig.5). Increased risk of personal injury, as well as damage to the

shoe and workpiece may result.

FIG. 5

TO INSTALL BLADE INTO SAW

1. Pull blade clamp release lever (C) up

FIG. 6

(Fig. 6).

2. Insert blade shank from the front.

3. Push blade clamp release lever down.

NOTE: The blade can be installed in the

DCS380 in four positions as shown in

Figure 7. The blade can be installed in

the DCS381 in two positions as shown in

Figure 7. Both units allow the blade to be

installed upside-down to assist in flush-to

cutting; see Figure 11.

FUEL GAUGE BATTERY PACKS (FIG. 4A)

Some D

EWALT battery packs include a

FIG. 4A

fuel gauge which consists of three

green LED lights that indicate the level

of charge remaining in the battery

pack.

To actuate the fuel gauge, press and

hold the fuel gauge button (H). A

combination of the three green LED

lights will illuminate designating the

level of charge left. When the level of

charge in the battery is below the usable limit, the fuel gauge will not

illuminate and the battery will need to be recharged.

NOTE: The fuel gauge is only an indication of the charge left on the

battery pack. It does not indicate tool functionality and is subject to

variation based on product components, temperature and end-user

application.

For more information regarding fuel gauge battery packs, please call

1-800-4-D

EWALT (1-800-433-9258) or visit our website www.dewalt.

com.

Blade Installation and Removal

(Fig. 5–7, 11)

WARNING: To reduce the risk of serious personal injury,

turn tool off and disconnect tool from power source before

making any adjustments or removing/installing attachments or

accessories. An accidental start-up can cause injury.

Different blade lengths are available. Use the appropriate blade for

the application. The blade should be longer than 3-1/2" (89 mm)

and should extend past the shoe and the thickness of the workpiece

during the cut. Do not use jigsaw blades with this tool.

English

Cutting with Blade in Horizontal Position

(DCS380 only) (Fig. 8)

Your DCS380 is equipped with a horizontal blade clamp. Installing a

blade in the horizontal orientation allows cutting close to floors, walls

or ceilings where limited clearance is available. Ensure that the shoe is

pressed against the framing to avoid kickback.

FIG. 8

Adjustable Shoe (DCS380 only) (Fig. 2, 9)

CAUTION: Cut hazard. To prevent loss of control, never use tool

without shoe.

Your DCS380 comes with an adjustable

FIG. 9

shoe. The shoe will adjust to limit the

depth of cut. Hold the saw with the

underside facing up. Push the button on

the hand grip and slide the shoe out to

one of the three settings and release the

button.

The DCS381 comes with a fixed shoe that

is not adjustable.

Cutting (Fig. 10–13)

WARNING: Always use eye protection. All users and bystanders

must wear eye protection that conforms to ANSI Z87.1.

FIG. 7

DCS381

DCS380

TO REMOVE BLADE FROM SAW

CAUTION: Burn hazard. Do not touch the the blade immediately

after use. Contact with the blade may result in personal injury.

1. Open up blade clamp release lever.

2. Remove blade.

English

WARNING: Exercise extra caution when cutting towards operator.

Always hold saw firmly with both hands while cutting.

Before cutting any type of material, be sure it is firmly anchored or

clamped to prevent slipping. Place blade lightly against work to be

cut, switch on saw motor and allow it to obtain maximum speed

before applying pressure. Whenever possible, the saw shoe must be

held firmly against the material being cut (Fig. 10). This will prevent the

saw from jumping or vibrating and minimize blade breakage. Any cuts

which put pressure on the blade such as angle or scroll cuts increase

potential for vibration, kickback, and blade breakage.

FIG. 10

WARNING: Use extra caution when cutting overhead and pay

particular attention to overhead wires which may be hidden from

view. Anticipate the path of falling branches and debris ahead of time.

WARNING: Inspect work site for hidden gas pipes, water pipes,

or electrical wires before making blind or plunge cuts. Failure to do

so may result in explosion, property damage, electric shock, and/or

serious personal injury.

FLUSH-TO CUTTING (FIG. 11)

The compact design of the saw motor housing and spindle housing

permits extremely close cutting to floors, corners and other difficult

areas.

FIG. 11

FIG. 12

1. STARTING POSITION FOR POCKET

CUTTING

2. ROCK TOOL UP TO NORMAL CUTTING

POSITION AFTER BLADE HAS CUT

THROUGH MATERIAL.

POCKET/PLUNGE CUTTING – WOOD ONLY (FIG. 12)

The initial step in pocket cutting is to measure the surface area to be

cut and mark clearly with a pencil, chalk or scriber. Use the appropriate

blade for the application. The blade should be longer than 3-1/2"

(89 mm) and should extend past the shoe and the thickness of the

workpiece during the cut. Insert blade in blade clamp.

Next, tip the saw backward until the back edge of the shoe is resting

on the work surface and the blade clears the work surface (position 1,

Fig.12). Now switch motor on, and allow saw to come up to speed.

Grip saw firmly with both hands and begin a slow, deliberate upward

swing with the handle of the saw, keeping the bottom of the shoe

firmly in contact with the workpiece (position 2, Fig. 12). Blade will

begin to feed into material. Always be sure blade is completely through

material before continuing with pocket cut.

English

NOTE: In areas where blade visibility is limited, use the edge of the

saw shoe as a guide. Lines for any given cut should be extended

beyond edge of cut to be made.

METAL CUTTING (FIG. 13)

Your saw has different

FIG. 13

metal cutting capacities

depending upon type of

blade used and the metal

to be cut. Use a finer

blade for ferrous metals

and a coarse blade for

non-ferrous materials. In

thin gauge sheet metals it

is best to clamp wood to

both sides of sheet. This

will insure a clean cut

without excess vibration

or tearing of metal. Always

remember not to force

cutting blade as this reduces blade life and causes costly blade

breakage.

NOTE: It is generally recommended that when cutting metals you

should spread a thin film of oil or other lubricant along the line ahead

of the saw cut for easier operation and longer blade life.

MAINTENANCE

WARNING: To reduce the risk of serious personal injury,

turn tool off and disconnect tool from power source before

making any adjustments or removing/installing attachments or

accessories. An accidental start-up can cause injury.

Cleaning

WARNING: Blow dirt and dust out of all air vents with clean, dry air

at least once a week. To minimize the risk of eye injury, always wear

ANSI Z87.1 approved eye protection when performing this.

WARNING: Never use solvents or other harsh chemicals for

cleaning the non-metallic parts of the tool. These chemicals may

weaken the plastic materials used in these parts. Use a cloth

dampened only with water and mild soap. Never let any liquid get

inside the tool; never immerse any part of the tool into a liquid.

CHARGER CLEANING INSTRUCTIONS

WARNING: Shock hazard. Disconnect the charger from the AC

outlet before cleaning. Dirt and grease may be removed from the

exterior of the charger using a cloth or soft non-metallic brush. Do

not use water or any cleaning solutions.

Accessories

WARNING: Since accessories, other than those offered by

EWALT, have not been tested with this product, use of such

accessories with this tool could be hazardous. To reduce the risk of

injury, only D

EWALT recommended accessories should be used with

this product.

Recommended accessories for use with your tool are available at

extra cost from your local service center. If you need any assistance in

locating any accessory, please contact D

EWALT Industrial Tool Co.,

701 East Joppa Road, Baltimore, MD 21286, call 1-800-4-D

EWALT

(1-800-433-9258) or visit our website www.dewalt.com.

Repairs

The charger and battery pack are not serviceable. There are no

serviceable parts inside the charger or battery pack.

To assure product SAFETY and RELIABILITY, repairs, maintenance

and adjustments (including brush inspection and replacement) should

English

be performed by a DEWALT factory service center, a DEWALT

authorized service center or other qualified service personnel. Always

use identical replacement parts.

Thank you for your purchase. Register your product now for:

• WARRANTY SERVICE: Registering your product will help you

obtain more efficient warranty service in case there is a problem

with your product.

• CONFIRMATION OF OWNERSHIP: In case of an insurance

loss, such as fire, flood or theft, your registration of ownership will

serve as your proof of purchase.

• FOR YOUR SAFETY: Registering your product will allow us to

contact you in the unlikely event a safety notification is required

under the Federal Consumer Safety Act.

Three Year Limited Warranty

DEWALT will repair, without charge, any defects due to faulty materials

or workmanship for three years from the date of purchase. This

warranty does not cover part failure due to normal wear or tool abuse.

For further detail of warranty coverage and warranty repair information,

visit www.dewalt.com or call 1-800-4-D

EWALT (1-800-433-9258).

This warranty does not apply to accessories or damage caused where

repairs have been made or attempted by others. This warranty gives

you specific legal rights and you may have other rights which vary in

certain states or provinces.

In addition to the warranty, D

EWALT tools are covered by our:

1 YEAR FREE SERVICE

EWALT will maintain the tool and replace worn parts caused by

normal use, for free, any time during the first year after purchase.

2 YEARS FREE SERVICE ON D

EWALT BATTERY PACKS

DC9071, DC9091, DC9096, DC9280, DC9360, DC9180, DCB120,

DCB127, DCB201, DCB203 and DCB207.

3 YEARS FREE SERVICE ON D

EWALT BATTERY PACKS

DCB200, DCB204, DCB205

EWALT BATTERY PACKS

Product warranty voided if the battery pack is tampered with in any

way. D

EWALT is not responsible for any injury caused by tampering

and may prosecute warranty fraud to the fullest extent permitted by

law.

90 DAY MONEY BACK GUARANTEE

If you are not completely satisfied with the performance of your

EWALT Power Tool, Laser, or Nailer for any reason, you can return it

within 90 days from the date of purchase with a receipt for a full refund

– no questions asked.

LATIN AMERICA: This warranty does not apply to products sold

in Latin America. For products sold in Latin America, see country

specific warranty information contained in the packaging, call the local

company or see website for warranty information.

FREE WARNING LABEL REPLACEMENT:

If your warning labels become illegible or are missing, call

1-800-4-D

EWALT (1-800-433-9258) for a free replacement.

Français

Déﬁ nitions: lignes directrices en

matière de sécurité

Les définitions ci-dessous décrivent le niveau de danger pour chaque

mot-indicateur employé. Lire le mode d’emploi et porter une

attention particulière à ces symboles.

DANGER : indique une situation dangereuse imminente qui,

si elle n’est pas évitée, entraînera la mort ou des blessures

graves.

AVERTISSEMENT : indique une situation potentiellement

dangereuse qui, si elle n’est pas évitée, pourrait entraîner la mort

ou des blessures graves.

ATTENTION: indique une situation potentiellement dangereuse

qui, si elle n’est pas évitée, pourrait entraîner des blessures

légères ou modérées.

AVIS : indique une pratique ne posant aucun risque de

dommages corporels mais qui par contre, si rien n’est fait pour

l’éviter, pourrait poser des risques de dommages matériels.

POUR TOUTE QUESTION OU REMARQUE AU SUJET DE CET OUTIL

OU DE TOUT AUTRE OUTIL D

EWALT, COMPOSEZ LE NUMÉRO

SANS FRAIS : 1 800 433-9258 (1 800 4-D

EWALT).

AVERTISSEMENT : afin de réduire le risque de blessures, lire

le mode d’emploi de l’outil.

Avertissements de sécurité généraux pour

les outils électriques

AVERTISSEMENT ! Lire tous les avertissements de

sécurité et toutes les directives. Le non-respect des

avertissements et des directives pourrait se solder par un choc

électrique, un incendie et/ou une blessure grave.

CONSERVER TOUS LES AVERTISSEMENTS

ET TOUTES LES DIRECTIVES POUR UN

USAGE ULTÉRIEUR

Le terme « outil électrique » cité dans les avertissements se rapporte

à votre outil électrique à alimentation sur secteur (avec fil) ou par piles

(sans fil).

1) SÉCURITÉ DU LIEU DE TRAVAIL

a) Tenir l’aire de travail propre et bien éclairée. Les lieux

encombrés ou sombres sont propices aux accidents.

b) Ne pas faire fonctionner d’outils électriques dans un

milieu déflagrant, tel qu’en présence de liquides, de

gaz ou de poussières inflammables. Les outils électriques

produisent des étincelles qui pourraient enflammer la poussière

ou les vapeurs.

c) Éloigner les enfants et les personnes à proximité pendant

l’utilisation d’un outil électrique. Une distraction pourrait en

faire perdre la maîtrise à l’utilisateur.

2) SÉCURITÉ EN MATIÈRE D’ÉLECTRICITÉ

a) Les fiches des outils électriques doivent correspondre

à la prise. Ne jamais modifier la fiche d’aucune façon.

Ne jamais utiliser de fiche d’adaptation avec un outil

électrique mis à la terre. Le risque de choc électrique sera

réduit par l’utilisation de fiches non modifiées correspondant à

la prise.

b) Éviter tout contact physique avec des surfaces mises à la

terre comme des tuyaux, des radiateurs, des cuisinières

et des réfrigérateurs. Le risque de choc électrique est plus

élevé si votre corps est mis à la terre.

c) Ne pas exposer les outils électriques à la pluie ou à

l’humidité. La pénétration de l’eau dans un outil électrique

augmente le risque de choc électrique.

Français

d) Ne pas utiliser le cordon de façon abusive. Ne jamais

utiliser le cordon pour transporter, tirer ou débrancher un

outil électrique. Tenir le cordon éloigné de la chaleur, de

l’huile, des bords tranchants et des pièces mobiles. Les

cordons endommagés ou enchevêtrés augmentent les risques

de choc électrique.

e) Pour l’utilisation d’un outil électrique à l’extérieur, se

servir d’une rallonge convenant à cette application.

L’utilisation d’une rallonge conçue pour l’extérieur réduira les

risques de choc électrique.

f) S’il est impossible d’éviter l’utilisation d’un outil électrique

dans un endroit humide, brancher l’outil dans une prise

ou sur un circuit d’alimentation dotés d’un disjoncteur de

fuite à la terre (GFCI). L’utilisation de ce type de disjoncteur

réduit les risques de choc électrique.

3) SÉCURITÉ PERSONNELLE

a) Être vigilant, surveiller le travail effectué et faire preuve

de jugement lorsqu’un outil électrique est utilisé. Ne

pas utiliser d’outil électrique en cas de fatigue ou sous

l’influence de drogues, d’alcool ou de médicaments. Un

simple moment d’inattention en utilisant un outil électrique peut

entraîner des blessures corporelles graves.

b) Utiliser des équipements de protection individuelle.

Toujours porter une protection oculaire. L’utilisation

d’équipements de protection comme un masque antipoussière,

des chaussures antidérapantes, un casque de sécurité ou des

protecteurs auditifs lorsque la situation le requiert réduira les

risques de blessures corporelles.

c) Empêcher les démarrages intempestifs. S’assurer que

l’interrupteur se trouve à la position d’arrêt avant de

relier l’outil à une source d’alimentation et/ou d’insérer

un bloc-piles, de ramasser ou de transporter l’outil.

Transporter un outil électrique alors que le doigt repose sur

l’interrupteur ou brancher un outil électrique dont l’interrupteur

est à la position de marche risque de provoquer un accident.

d) Retirer toute clé de réglage ou clé avant de démarrer

l’outil. Une clé ou une clé de réglage attachée à une partie

pivotante de l’outil électrique peut provoquer des blessures

corporelles.

e) Ne pas trop tendre les bras. Conserver son équilibre en

tout temps. Cela permet de mieux maîtriser l’outil électrique

dans les situations imprévues.

f) S’habiller de manière appropriée. Ne pas porter de

vêtements amples ni de bijoux. Garder les cheveux, les

vêtements et les gants à l’écart des pièces mobiles. Les

vêtements amples, les bijoux ou les cheveux longs risquent de

rester coincés dans les pièces mobiles.

g) Si des composants sont fournis pour le raccordement de

dispositifs de dépoussiérage et de ramassage, s’assurer

que ceux-ci sont bien raccordés et utilisés. L’utilisation d’un

dispositif de dépoussiérage peut réduire les dangers engendrés

par les poussières.

4) UTILISATION ET ENTRETIEN D’UN OUTIL ÉLECTRIQUE

a) Ne pas forcer un outil électrique. Utiliser l’outil électrique

approprié à l’application. L’outil électrique approprié

effectuera un meilleur travail, de façon plus sûre et à la vitesse

pour laquelle il a été conçu.

b) Ne pas utiliser un outil électrique dont l’interrupteur

est défectueux. Tout outil électrique dont l’interrupteur est

défectueux est dangereux et doit être réparé.

c) Débrancher la fiche de la source d’alimentation et/ou du

bloc-piles de l’outil électrique avant de faire tout réglage

ou changement d’accessoire ou avant de ranger l’outil.

Ces mesures préventives réduisent les risques de démarrage

accidentel de l’outil électrique.

Français

d) Ranger les outils électriques hors de la portée des

enfants et ne permettre à aucune personne n’étant pas

familière avec un outil électrique ou son mode d’emploi

d’utiliser cet outil. Les outils électriques deviennent dangereux

entre les mains d’utilisateurs inexpérimentés.

e) Entretien des outils électriques. Vérifier si les pièces

mobiles sont mal alignées ou coincées, si des pièces sont

brisées ou présentent toute autre condition susceptible

de nuire au bon fonctionnement de l’outil électrique. En

cas de dommage, faire réparer l’outil électrique avant

toute nouvelle utilisation. Beaucoup d’accidents sont causés

par des outils électriques mal entretenus.

f) S’assurer que les outils de coupe sont aiguisés et

propres. Les outils de coupe bien entretenus et affûtés

sont moins susceptibles de se coincer et sont plus faciles à

maîtriser.

g) Utiliser l’outil électrique, les accessoires, les forets,

etc. conformément aux présentes directives en tenant

compte des conditions de travail et du travail à effectuer.

L’utilisation d’un outil électrique pour toute opération autre que

celle pour laquelle il a été conçu est dangereuse.

5) UTILISATION ET ENTRETIEN DU BLOC-PILES

a) Ne recharger l’outil qu’au moyen du chargeur précisé par

le fabricant. L’utilisation d’un chargeur qui convient à un type

de bloc-piles risque de provoquer un incendie s’il est utilisé avec

un autre type de b loc-piles.

b) Utiliser les outils électriques uniquement avec les blocs-

piles conçus à cet effet. L’utilisation de tout autre bloc-piles

risque de causer des blessures ou un incendie.

c) Lorsque le bloc-piles n’est pas utilisé, le tenir éloigné

des objets métalliques, notamment des trombones, de

la monnaie, des clés, des clous, des vis ou autres petits

objets métalliques qui peuvent établir une connexion

entre les deux bornes. Le court-circuit des bornes du bloc-

piles risque de provoquer des brûlures ou un incendie.

d) En cas d’utilisation abusive, le liquide peut gicler hors

du bloc-piles; éviter tout contact avec ce liquide. Si un

contact accidentel se produit, laver à grande eau. Si le

liquide entre en contact avec les yeux, obtenir également

des soins médicaux. Le liquide qui gicle hors du bloc-piles

peut provoquer des irritations ou des brûlures.

6) RÉPARATION

a) Faire réparer l’outil électrique par un réparateur

professionnel en n’utilisant que des pièces de rechange

identiques. Cela permettra de maintenir une utilisation

sécuritaire de l’outil électrique.

Règles particulières additionnelles de

sécurité propres aux scies alternatives

• Tenir l’outil par les surfaces isolées prévues à cet effet pen-

dant toute utilisation où l’organe de coupe pourrait entrer

en contact avec des fils électriques cachés. Tout contact de

l’organe de coupe avec un fil sous tension mettra les parties métal-

liques exposées de l’outil sous tension et électrocutera l’utilisateur.

• Utilisez des serres de fixation ou un autre dispositif de fixa-

tion permettant de soutenir et de retenir la pièce sur une

plate-forme stable. Tenir la pièce avec la main ou contre son

corps n’est pas suffisamment stable et risque de provoquer une

perte de maîtrise de l’outil.

• Maintenir la scie fermement à deux mains lors de toute

coupe. Pendant la découpe, la lame pourrait soudainement se

bloquer dans la pièce à travailler et causer un rebond de la scie vers

l’utilisateur.

• Tenir les mains à l'écart de toute pièce mobile. Ne jamais

approcher les mains des zones de coupes.

La page est en cours de chargement...

DeWalt DCS380B Le manuel du propriétaire

Marque: DeWalt

Modèle: DCS380B

Taper: Le manuel du propriétaire

Ce manuel convient également à

DCS380B 20V MAX Lithium-Ion Variable Speed Cordless

Télécharger le PDF

rapport

dans d''autres langues

English: DeWalt DCS380B Owner's manual
español: DeWalt DCS380B El manual del propietario

DeWalt DCS380B Le manuel du propriétaire

Ce manuel convient également à

DeWalt DCS380B Le manuel du propriétaire

dans d''autres langues

Documents connexes