DeWalt DCK940D2WDCE100 Manuel utilisateur

DCS355

20V Max* Oscillating Multi-Tool

Outil multifonctions à oscillations sans fil 20V max*

Multi-herramienta oscilante inalámbrica de 20 V Máx

INSTRUCTION MANUAL

GUIDE D’UTILISATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE

GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE

USAR EL PRODUCTO.

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-D

e

WALT • www.dewalt.com

FINAL PRINT SIZE: 8.5 x 5.5"

Deﬁnitions: Safety Guidelines

The definitions below describe the level of severity for each

signal word. Please read the manual and pay attention to these

symbols.

DANGER: Indicates an imminently hazardous situation

which, if not avoided, will result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which,

if not avoided, could result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which,

if not avoided, may result in minor or moderate injury.

NOTICE: Indicates a practice not related to personal injury

which, if not avoided, may result in property damage.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR

ANY D

e

WALT TOOL, CALL US TOLL FREE AT: 1-800-4-D

e

WALT

(1-800-433-9258).

WARNING: To reduce the risk of injury, read the instruction

manual.

General Power Tool Safety Warnings

WARNING! Read all safety warnings and all instructions.

Failure to follow the warnings and instructions may result in

electric shock, fire and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

The term “power tool” in the warnings refers to your mains-operated

(corded) power tool or battery-operated (cordless) power tool.

1) WORK AREA SAFETY

a) Keep work area clean and well lit. Cluttered or dark areas

invite accidents.

b) Do not operate power tools in explosive atmospheres,

such as in the presence of flammable liquids, gases or

dust. Power tools create sparks which may ignite the dust or

fumes.

c) Keep children and bystanders away while operating a

power tool. Distractions can cause you to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet. Never modify

the plug in any way. Do not use any adapter plugs with

earthed (grounded) power tools. Unmodified plugs and

matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces

such as pipes, radiators, ranges and refrigerators. There

is an increased risk of electric shock if your body is earthed or

grounded.

c) Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of electric

shock.

d) Do not abuse the cord. Never use the cord for carrying,

pulling or unplugging the power tool. Keep cord away

from heat, oil, sharp edges or moving parts. Damaged or

entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension

cord suitable for outdoor use. Use of a cord suitable for

outdoor use reduces the risk of electric shock.

f) If operating a power tool in a damp location is unavoidable,

use a ground fault circuit interrupter (GFCI) protected

supply. Use of a GFCI reduces the risk of electric shock.

English

1

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and use common

sense when operating a power tool. Do not use a power

tool while you are tired or under the influence of drugs,

alcohol or medication. A moment of inattention while

operating power tools may result in serious personal injury.

b) Use personal protective equipment. Always wear eye

protection. Protective equipment such as dust mask, non-

skid safety shoes, hard hat, or hearing protection used for

appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in

the off position before connecting to power source and/

or battery pack, picking up or carrying the tool. Carrying

power tools with your finger on the switch or energizing power

tools that have the switch on invites accidents.

d) Remove any adjusting key or wrench before turning the

power tool on. A wrench or a key left attached to a rotating

part of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at

all times. This enables better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose clothing or jewelry.

Keep your hair, clothing and gloves away from moving

parts. Loose clothes, jewelry or long hair can be caught in

moving parts.

g) If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection can

reduce dust-related hazards.

4) POWER TOOL USE AND CARE

a) Do not force the power tool. Use the correct power tool

for your application. The correct power tool will do the job

better and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not turn it

on and off. Any power tool that cannot be controlled with the

switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the

battery pack from the power tool before making any

adjustments, changing accessories, or storing power

tools. Such preventive safety measures reduce the risk of

starting the power tool accidentally.

d) Store idle power tools out of the reach of children and

do not allow persons unfamiliar with the power tool or

these instructions to operate the power tool. Power tools

are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding

of moving parts, breakage of parts and any other

condition that may affect the power tool’s operation. If

damaged, have the power tool repaired before use. Many

accidents are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly maintained

cutting tools with sharp cutting edges are less likely to bind and

are easier to control.

g) Use the power tool, accessories and tool bits, etc. in

accordance with these instructions, taking into account

the working conditions and the work to be performed.

Use of the power tool for operations different from those

intended could result in a hazardous situation.

English

2

5) BATTERY TOOL USE AND CARE

a) Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type of

battery pack may create a risk of fire when used with another

battery pack.

b) Use power tools only with specifically designated battery

packs. Use of any other battery packs may create a risk of

injury and fire.

c) When battery pack is not in use, keep it away from

other metal objects, like paper clips, coins, keys, nails,

screws, or other small metal objects, that can make a

connection from one terminal to another. Shorting the

battery terminals together may cause burns or a fire.

d) Under abusive conditions, liquid may be ejected from

the battery; avoid contact. If contact accidentally occurs,

flush with water. If liquid contacts eyes, additionally seek

medical help. Liquid ejected from the battery may cause

irritation or burns.

6) SERVICE

a) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained.

Additional Safety Rules for Oscillating

Multi-Tool

• Hold power tool by insulated gripping surfaces, when

performing an operation where the cutting accessory may

contact hidden wiring or its own cord. Cutting accessory

contacting a "live" wire may make exposed metal parts of the

power tool "live" and could give the operator an electric shock.

• Use clamps or another practical way to secure and support

the workpiece to a stable platform. Holding the work by hand

or against your body leaves it unstable and may lead to loss of

control.

• Air vents often cover moving parts and should be avoided.

Loose clothes, jewelry or long hair can be caught in moving parts.

WARNING: ALWAYS use safety glasses. Everyday eyeglasses are

NOT safety glasses. Also use face or dust mask if cutting operation is

dusty. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratory protection.

WARNING: Some dust created by power sanding, sawing,

grinding, drilling, and other construction activities contains chemicals

known to the State of California to cause cancer, birth defects or other

reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry

products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you

do this type of work. To reduce your exposure to these chemicals:

work in a well ventilated area, and work with approved safety

equipment, such as those dust masks that are specially designed to

filter out microscopic particles.

• Avoid prolonged contact with dust from power sanding,

sawing, grinding, drilling, and other construction activities.

Wear protective clothing and wash exposed areas with

soap and water. Allowing dust to get into your mouth, eyes, or

lay on the skin may promote absorption of harmful chemicals.

English

3

WARNING: Use of this tool can generate and/or disperse dust,

which may cause serious and permanent respiratory or other

injury. Always use NIOSH/OSHA approved respiratory protection

appropriate for the dust exposure. Direct particles away from face

and body.

WARNING: Always wear proper personal hearing protection

that conforms to ANSI S12.6 (S3.19) during use. Under some

conditions and duration of use, noise from this product may

contribute to hearing loss.

CAUTION: When not in use, place tool on its side on a stable

surface where it will not cause a tripping or falling hazard.

Some tools with large battery packs will stand upright on the battery

pack but may be easily knocked over.

• The label on your tool may include the following symbols. The

symbols and their definitions are as follows:

V ...................volts A ...................... amperes

Hz ................. hertz W ..................... watts

min ............... minutes or AC ..........alternating

or DC ... direct current current

................. Class I Construction or AC/DC ... alternating or

(grounded) ........................direct current

................. Class II Construction

n

o ....................no load

(double insulated) speed

…/min ........... per minute n ......................rated speed

BPM ............. beats per minute .....................earthing

IPM ............... impacts per minute terminal

RPM ............. revolutions per ..................... safety alert

minute symbol

sfpm ............. surface feet SPM ................strokes per

..................... per minute ........................minute

................. visible radiation

Important Safety Instructions for All

Battery Packs

When ordering replacement battery packs, be sure to include the

catalog number and voltage. Consult the chart at the end of this

manual for compatibility of chargers and battery packs.

The battery pack is not fully charged out of the carton. Before using

the battery pack and charger, read the safety instructions below and

then follow charging procedures outlined.

READ ALL INSTRUCTIONS

• Do not charge or use the battery pack in explosive

atmospheres, such as in the presence of flammable liquids,

gases or dust. Inserting or removing the battery pack from the

charger may ignite the dust or fumes.

• NEVER force the battery pack into the charger. DO NOT

modify the battery pack in any way to fit into a non-

compatible charger as battery pack may rupture causing

serious personal injury. Consult the chart at the end of this

manual for compatibility of batteries and chargers.

• Charge the battery packs only in designated D

e

WALT chargers.

• DO NOT splash or immerse in water or other liquids.

• Do not store or use the tool and battery pack in locations

where the temperature may reach or exceed 104°F (40°C)

(such as outside sheds or metal buildings in summer). For

best life store battery packs in a cool, dry location.

NOTE: Do not store the battery packs in a tool with the

trigger switch locked on. Never tape the trigger switch in

the ON position.

WARNING: Fire hazard. Never attempt to open the battery pack

for any reason. If the battery pack case is cracked or damaged, do

not insert into the charger. Do not crush, drop or damage the battery

pack. Do not use a battery pack or charger that has received a sharp

English

4

blow, been dropped, run over or damaged in any way (e.g., pierced

with a nail, hit with a hammer, stepped on). Damaged battery packs

should be returned to the service center for recycling.

WARNING: Fire hazard. Do not store or carry the battery

pack so that metal objects can contact exposed battery

terminals. For example, do not place the battery pack in aprons,

pockets, tool boxes, product kit boxes, drawers, etc., with loose nails,

screws, keys, etc. Transporting batteries can possibly cause

fires if the battery terminals inadvertently come in contact

with conductive materials such as keys, coins, hand tools

and the like. The US Department of Transportation Hazardous

Material Regulations (HMR) actually prohibit transporting batteries in

commerce or on airplanes (e.g., packed in suitcases and carry-on

luggage) UNLESS they are properly protected from short circuits. So

when transporting individual battery packs, make sure that the battery

terminals are protected and well insulated from materials that could

contact them and cause a short circuit.

SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION (Li-Ion)

• Do not incinerate the battery pack even if it is severely

damaged or is completely worn out. The battery pack can

explode in a fire. Toxic fumes and materials are created when

lithium ion battery packs are burned.

• If battery contents come into contact with the skin,

immediately wash area with mild soap and water. If battery

liquid gets into the eye, rinse water over the open eye for 15

minutes or until irritation ceases. If medical attention is needed,

the battery electrolyte is composed of a mixture of liquid organic

carbonates and lithium salts.

• Contents of opened battery cells may cause respiratory

irritation. Provide fresh air. If symptoms persist, seek medical

attention.

WARNING: Burn hazard. Battery liquid may be flammable if

exposed to spark or flame.

The RBRC

®

Seal

The RBRC

®

(Rechargeable Battery Recycling

Corp oration) Seal on the nickel cadmium, nickel metal

hydride or lithium-ionbatteries (or battery packs)

indicates that the costs to recycle these batteries (or

battery packs) at the end of their useful life have already

been paid by D

e

WALT. In some areas, it is illegal to

place spent nickel cadmium, nickel metal hydride or lithium-ion

batteries in the trash or municipal solid waste stream and the Call 2

Recycle

®

program provides an environmentally conscious alternative.

Call 2 Recycle, Inc., in cooperation with D

e

WALT and other battery

users, has established the program in the United States and Canada

to facilitate the collection of spent nickel cadmium, nickel metal

hydride or lithium-ion batteries. Help protect our environment and

conserve natural resources by returning the spent nickel cadmium,

nickel metal hydride or lithium-ion batteries to an authorized D

e

WALT

service center or to your local retailer for recycling. You may also

contact your local recycling center for information on where to drop

off the spent battery. RBRC

®

is a registered trademark of Call 2

Recycle, Inc.

Important Safety Instructions for All

Battery Chargers

SAVE THESE INSTRUCTIONS: This manual contains important

safety and operating instructions for battery chargers.

• Before using the charger, read all instructions and cautionary

markings on the charger, battery pack and product using the

battery pack.

WARNING: Shock hazard. Do not allow any liquid to get inside the

charger. Electric shock may result.

English

5

CAUTION: Burn hazard. To reduce the risk of injury, charge only

D

e

WALT rechargeable battery packs. Other types of batteries may

overheat and burst resulting in personal injury and property damage.

NOTICE: Under certain conditions, with the charger plugged into

the power supply, the charger can be shorted by foreign material.

Foreign materials of a conductive nature, such as, but not limited to,

grinding dust, metal chips, steel wool, aluminum foil or any buildup

of metallic particles should be kept away from the charger cavities.

Always unplug the charger from the power supply when there is no

battery pack in the cavity. Unplug the charger before attempting to

clean.

• DO NOT attempt to charge the battery pack with any

chargers other than the ones in this manual. The charger and

battery pack are specifically designed to work together.

• These chargers are not intended for any uses other than

charging D

e

WALT rechargeable batteries. Any other uses

may result in risk of fire, electric shock or electrocution.

• Do not expose the charger to rain or snow.

• Pull by the plug rather than the cord when disconnecting

the charger. This will reduce the risk of damage to the electric

plug and cord.

• Make sure that the cord is located so that it will not be

stepped on, tripped over or otherwise subjected to damage

or stress.

• Do not use an extension cord unless it is absolutely

necessary. Use of improper extension cord could result in risk of

fire, electric shock or electrocution.

• When operating a charger outdoors, always provide a dry

location and use an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces the risk of electric

shock.

• An extension cord must have adequate wire size (AWG or

American Wire Gauge) for safety. The smaller the gauge number

of the wire, the greater the capacity of the cable, that is, 16 gauge

has more capacity than 18 gauge. An undersized cord will cause a

drop in line voltage resulting in loss of power and overheating. When

using more than one extension to make up the total length, be sure

each individual extension contains at least the minimum wire size.

The following table shows the correct size to use depending on

cord length and nameplate ampere rating. If in doubt, use the next

heavier gauge. The lower the gauge number, the heavier the cord.

Minimum Gauge for Cord Sets

Ampere

Rating

Volts Total Length of Cord

in Feet (meters)

120 V 25

(7.6)

50

(15.2)

100

(30.5)

150

(45.7)

240 V 50

(15.2)

100

(30.5)

200

(61.0)

300

(91.4)

More

Than

Not

More

Than

AWG

0 6 18 16 16 14

6 10 18 16 14 12

10 12 16 16 14 12

12 16 14 12 Not Recommended

• Do not place any object on top of the charger or place the

charger on a soft surface that might block the ventilation

slots and result in excessive internal heat. Place the charger

in a position away from any heat source. The charger is ventilated

through slots in the top and the bottom of the housing.

• Do not operate the charger with a damaged cord or plug.

• Do not operate the charger if it has received a sharp blow,

been dropped or otherwise damaged in any way. Take it to

an authorized service center.

English

6

• Do not disassemble the charger; take it to an authorized

service center when service or repair is required. Incorrect

reassembly may result in a risk of electric shock, electrocution or fire.

• Disconnect the charger from the outlet before attempting

any cleaning. This will reduce the risk of electric shock.

Removing the battery pack will not reduce this risk.

• NEVER attempt to connect 2 chargers together.

• The charger is designed to operate on standard 120V

household electrical power. Do not attempt to use it on any

other voltage. This does not apply to the vehicular charger.

Chargers

Your tool uses a D

e

WALT charger. Be sure to read all safety

instructions before using your charger. Consult the chart at the end of

this manual for compatibility of chargers and battery packs.

Charging Procedure (Fig. 1)

1. Plug the charger into an appropriate

DCB101

H

FIG. 1

outlet before inserting the battery

pack.

2. Insert the battery pack (H) into

the charger, as shown in Figure 1,

making sure the pack is fully seated

in charger. The red (charging) light

will blink continuously, indicating that

the charging process has started.

3. The completion of charge will be

indicated by the red light remaining

ON continuously. The pack is fully

charged and may be used at this

time or left in the charger.

Indicator Light Operation

DCB101, DCB102, DCB103

PACK CHARGING

PACK CHARGED

x

HOT/COLD DELAY

PROBLEM PACK OR CHARGER

DCB107, DCB112, DCB113, DCB115

PACK CHARGING

PACK CHARGED

HOT/COLD DELAY

Charge Indicators

This charger is designed to detect certain problems that can arise.

Problems are indicated by the red light flashing at a fast rate. If this

occurs, re-insert the battery pack into the charger. If the problem

persists, try a different battery pack to determine if the charger is

working properly. If the new pack charges correctly, then the original

pack is defective and should be returned to a service center or other

collection site for recycling. If the new battery pack elicits the same

trouble indication as the original, have the charger and the battery

pack tested at an authorized service center.

English

7

HOT/COLD DELAY

DCB101, DCB102, DCB103

These chargers have a hot/cold delay feature. When the charger

detects a battery that is too hot or too cold, it automatically starts

a delay, suspending charging. The red light flashes long, then short

while in the hot/cold delay mode.

Once the battery has reached an optimum temperature, the charger

will automatically resume the charging procedure. This feature

ensures maximum battery life.

DCB107, DCB112, DCB113, DCB115

These chargers have a hot/cold delay feature. When the charger

detects a battery that is too hot or too cold, it automatically starts a

delay, suspending charging. The red light will continue to blink, but a

yellow indicator light will be illuminated during this suspension.

Once the battery has reached an optimum temperature, the yellow

light will turn off and the charger will automatically resume the

charging procedure. This feature ensures maximum battery life.

LEAVING THE BATTERY PACK IN THE CHARGER

The charger and battery pack can be left connected with the charge

indicator showing Pack Charged.

WEAK BATTERY PACKS: Weak batteries will continue to function

but should not be expected to perform as much work.

FAULTY BATTERY PACKS

DCB101, DCB102, DCB103

These chargers will not charge a faulty battery pack. The charger

will indicate faulty battery pack by refusing to light or by displaying

problem pack or charger.

NOTE: This could also mean a problem with a charger.

DCB107, DCB112, DCB113, DCB115

These chargers will not charge a faulty battery pack. The charger will

indicate faulty battery pack by refusing to light.

NOTE: This could also mean a problem with a charger.

Wall Mounting

DCB107, DCB112, DCB113, DCB115

These chargers are designed to be wall mountable or to sit upright on

a table or work surface.

If wall mounting, locate the charger within reach of an electrical

outlet. Mount the charger securely using drywall screws at least

1" (25.4 mm) long, screwed into wood to an optimal depth leaving

approximately 7/32" (5.5 mm) of the screw exposed.

Important Charging Notes

1. Longest life and best performance can be obtained if the battery

pack is charged when the air temperature is between 65°F and

75°F (18° – 24°C). DO NOT charge the battery pack in an air

temperature below +40°F (+4.5°C), or above +104°F (+40°C).

This is important and will prevent serious damage to the battery

pack.

2. The charger and battery pack may become warm to the touch

while charging. This is a normal condition, and does not indicate

a problem. To facilitate the cooling of the battery pack after use,

avoid placing the charger or battery pack in a warm environment

such as in a metal shed or an uninsulated trailer.

3. A cold battery pack will charge at about half the rate of a warm

battery pack. The battery pack will charge at that slower rate

throughout the entire charging cycle and will not return to

maximum charge rate even if the battery pack warms.

4. If the battery pack does not charge properly:

a. Check operation of receptacle by plugging in a lamp or other

appliance;

English

8

b. Check to see if receptacle is connected to a light switch which

turns power off when you turn out the lights;

c. Move the charger and battery pack to a location where the

surrounding air temperature is approximately 65 °F – 75 °F

(18° – 24°C);

d. If charging problems persist, take the tool, battery pack and

charger to your local service center.

5. The battery pack should be recharged when it fails to produce

sufficient power on jobs which were easily done previously. DO

NOT CONTINUE to use under these conditions. Follow the

charging procedure. You may also charge a partially used pack

whenever you desire with no adverse effect on the battery pack.

6. Foreign materials of a conductive nature such as, but not limited

to, grinding dust, metal chips, steel wool, aluminum foil, or any

buildup of metallic particles should be kept away from charger

cavities. Always unplug the charger from the power supply when

there is no battery pack in the cavity. Unplug the charger before

attempting to clean.

7. Do not freeze or immerse the charger in water or any other liquid.

WARNING: Shock hazard. Don’t allow any liquid to get inside the

charger. Electric shock may result.

WARNING: Burn hazard. Do not submerge the battery pack in

any liquid or allow any liquid to enter the battery pack. Never attempt

to open the battery pack for any reason. If the plastic housing of the

battery pack breaks or cracks, return to a service center for recycling.

Storage Recommendations

1. The best storage place is one that is cool and dry, away from

direct sunlight and excess heat or cold.

2. For long storage, it is recommended to store a fully charged

battery pack in a cool dry place out of the charger for optimal

results.

NOTE: Battery packs should not be stored completely depleted of

charge. The battery pack will need to be recharged before use.

SAVE THESE INSTRUCTIONS

FOR FUTURE USE

FIG. 2

A

D

F

C

E

B

G

HI

COMPONENTS (Fig. 2)

WARNING: Never modify the power tool or any part of it. Damage

or personal injury could result.

A. Variable speed trigger

B. LED worklight

C. Accessory clamp lever

D. Lock on/off button

E. Accessory side mount

F. Cut guide block

G. Cut guide arm

H. Battery pack

I. Battery release button

English

9

INTENDED USE

This oscillating multi-tool is designed for professional detail sanding,

plunge cutting, flush cutting, removal of excess materials and surface

preparation applications.

DO NOT use under wet conditions or in presence of flammable

liquids or gases.

This oscillating multi-tool is a professional power tool. DO NOT let

children come into contact with the tool. Supervision is required when

inexperienced operators use this tool.

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal injury,

turn tool off and remove the battery pack before making any

adjustments or removing/installing attachments or accessories.

An accidental start-up can cause injury.

WARNING: Risk of lacerations or burns. Do not touch the

sharp edges of accessories at any time. Do not touch workpiece

or blade immediately after operating the tool. They can become very

hot. Handle carefully. Always allow accessories and workpiece to

cool before handling.

Installing/Removing Accessories

(Fig.3–5)

TOOL-FREE ACCESSORY CLAMP

The DCS355 features a quick change accessory system. This allows

for faster accessory changes without the need for wrenches or hex

keys like other oscillating tool systems.

1. Grasp the tool and squeeze the

FIG. 3

C

J

accessory clamping lever (C) as

shown in Figure 3.

2. Clean any residual debris from the

tool shaft and the accessory holder.

3. Slide the accessory between the

shaft (J) and the accessory holder

making sure the accessory engages

all eight pins on the holder and is

flush with the shaft.

4. Release the accessory clamp lever.

NOTE: Some accessories, such as scrapers and blades, can be

mounted at an angle if required as shown in Figure 5.

FIG. 4 FIG. 5

INSTALLING/REMOVING SANDING SHEETS (FIG. 6)

A diamond shaped platen uses a hook and loop adhesion system to

attach the sanding sheets. The platen allows you to use it on large flat

surfaces and tight spots or corners.

1. Attach the sanding platen (K) as described under Installing/

Removing Accessories.

English

10

2. Align the edges on the sanding

FIG. 6

L

K

sheet, with the edge of the sanding

platen and press the sanding sheet

(L) onto the platen.

3. Firmly press the base with the

sanding sheet attached against a flat

surface and briefly switch the tool

on. This provides for good adhesion

between the platen and the sanding

sheet and also helps to prevent

premature wear.

4. When the tip of the sanding sheet

becomes worn, detach the sheet from the platen, rotate and

reapply.

ATTACHING ACCESSORIES USING THE UNIVERSAL

ADAPTER (FIG. 7)

Non-

DeWALT

accessories can be

attached using the universal adaptor.

1. Place the washer (M) on the tool.

2. Place accessory on to washer.

3. Tighten and secure adaptor nut (N)

using hex wrench.

CAUTION: To avoid injury, do not

use any accessory for an application

where the adaptor may fail to hold the

accessory.

CAUTION: Read and follow all manufacturers' safety warnings for

any accessories used with this tool.

CAUTION: To avoid injury, ensure adaptor and accessory are

securely tightened.

FIG. 7

M

N

Attaching the Cut Guide (Fig. 8–12)

The depth/cut guide allows you to precisely

cut material at a specified depth or height and

more accurately track a marked cut line.

1. Attach the cut guide block (F) by inserting

the tabs (O) on the guide into the

accessory side mount (E) on the main

body of the tool.

2. Secure the block to the main body with

the supplied screw (Q) and washer (S).

Tighten with the supplied hex wrench(R).

DEPTH GUIDE

This feature allows you to precisely cut

material at a specified depth.

1. Insert the guide arm (G) as shown in

Figure 9 into the front slot on the guide

block (F).

2. Adjust the length of the guide by pulling out or pushing inward to

achieve the desired cut depth as shown in Figure 10.

3. Secure the guide in place by turning the depth/cut adjustment

knob (P) clockwise. To release the guide, turn the depth/cut

adjustment knob counterclockwise.

P

FIG. 9

FIG. 10

F

G

E

O

Q

R

F

FIG. 8

S

English

11

CUT GUIDE

This feature allows you to more accurately track a marked cut line.

1. Insert the guide arm (G) as shown in Figure 11 into the slots on

the left and right sides of the guide block (F).

2. Adjust the length of the guide by pulling out or pushing inward to

achieve the desired length as shown in Figure 12.

3. Secure the guide in place by turning the depth/cut adjustment

knob (P) clockwise. To release the guide, turn the depth/cut

adjustment knob counterclockwise.

P

FIG. 11 FIG. 12

F

G

NOTE: The guide arm can also be placed in

the guard assembly vertically in order to set

the height of a cut. Refer to Figure 13.

OPERATION

WARNING: To reduce the risk of

serious personal injury, turn tool off and

remove the battery pack before making

any adjustments or removing/installing

attachments or accessories. An accidental

start-up can cause injury.

Installing and Removing the Battery Pack

(Fig. 14)

NOTE: For best results, make sure your battery pack is fully charged.

FIG. 13

To install the battery pack (H) into the tool handle, align the battery

pack with the rails inside the tool’s handle and slide it into the handle

until the battery pack is firmly seated in the tool and ensure that it

does not disengage.

To remove the battery pack from the tool, press the release button (I)

and firmly pull the battery pack out of the tool handle. Insert it into the

charger as described in the charger section of this manual.

FIG. 14

I

H

FUEL GAUGE BATTERY PACKS (FIG. 15)

Some D

e

WALT battery packs include a fuel gauge which consists of

three green LED lights that indicate the level of charge remaining in

the battery pack.

The fuel gauge is an indication of approximate levels of charge

remaining in the battery pack according to the following indicators:

75–100% charged

51–74% charged

< 50% charged

Pack needs to be charged

English

12

To actuate the fuel gauge, press and hold

T

FIG. 15

the fuel gauge button (T). A combination

of the three green LED lights will illuminate

designating the level of charge left. When

the level of charge in the battery is below

the usable limit, the fuel gauge will not

illuminate and the battery will need to be

recharged.

NOTE: The fuel gauge is only an indication of the charge left on the

battery pack. It does not indicate tool functionality and is subject to

variation based on product components, temperature and end-user

application.

For more information regarding fuel gauge battery packs, please call

1-800-4-D

e

WALT (1-800-433-9258) or visit our website www.dewalt.

com.

Variable Speed Trigger (Fig. 16)

WARNING: Ensure switch is fully OFF before installing the battery

pack.

1. Install the battery pack.

2. To turn the tool ON, hold it as shown in Figure 16 and press the

variable speed trigger (A).

NOTE: The further the trigger

switch is depressed, the faster

the tool will operate. If in doubt

about the proper speed for your

operation, test the performance

at low speed and gradually

increase until a comfortable

speed is found.

3. To turn the tool OFF, release the variable speed switch (A).

FIG. 16

A

Lock On/Off Button (Fig. 17)

Engage the lock on/off button (D), by pushing

it to the left or right. When the trigger (A) is

not depressed, pushing the button fully to

either side until it snaps into place will lock the

trigger and disable it from being depressed.

Placing the button in the center position

allows the trigger to operate normally.

Pushing the button to the left or right with the

trigger depressed will lock the trigger in the depressed position. This

allows for more comfort and control in extended use applications.

Pressing the trigger switch again will release the lock out and the tool

will turn off upon release of the trigger.

LED Worklight (Fig. 18)

CAUTION: Do not stare into worklight. Serious eye injury could

result.

The LED worklight (B) will activate any time the trigger is depressed

and will remain on for 20 seconds after trigger is released.

FIG. 18

B

Helpful Hints

• Always ensure the workpiece is firmly held or clamped to prevent

movement. Any movement of the material may affect the quality

of the cutting or sanding finish.

FIG. 17

A

D

English

13

• Do not start sanding without having the sandpaper attached to

sanding platen.

• Use coarse grit paper to sand rough surfaces, medium grit

for smooth surfaces and fine grit for the finishing surfaces. If

necessary, first make a test run on scrap material.

• Excessive force will reduce the working efficiency and cause

motor overload. Replacing the accessory regularly will maintain

optimum working efficiency.

• Do not allow the sandpaper to wear away, it will damage the

sanding pad.

• If the tool overheats, especially when used at low speed, set the

speed to maximum and run it with no load for 2–3 minutes to cool

the motor. Avoid prolonged usage at very low speeds. Always

keep the blade sharp.

MAINTENANCE

WARNING: To reduce the risk of serious personal injury,

turn tool off and remove the battery pack before making any

adjustments or removing/installing attachments or accessories.

An accidental start-up can cause injury.

Cleaning

WARNING: Blow dirt and dust out of all air vents with clean, dry air

at least once a week. To minimize the risk of eye injury, always wear

ANSI Z87.1 approved eye protection when performing this.

WARNING: Never use solvents or other harsh chemicals for

cleaning the non-metallic parts of the tool. These chemicals may

weaken the plastic materials used in these parts. Use a cloth

dampened only with water and mild soap. Never let any liquid get

inside the tool; never immerse any part of the tool into a liquid.

CHARGER CLEANING INSTRUCTIONS

WARNING: Shock hazard. Disconnect the charger from the AC

outlet before cleaning. Dirt and grease may be removed from the

exterior of the charger using a cloth or soft non-metallic brush. Do not

use water or any cleaning solutions.

Accessories

WARNING: Since accessories, other than those offered by

D

e

WALT, have not been tested with this product, use of such

accessories with this tool could be hazardous. To reduce the risk of

injury, only D

e

WALT recommended accessories should be used with

this product.

Recommended accessories for use with your tool are available

at extra cost from your local dealer or authorized service center. If

you need assistance in locating any accessory, please contact

D

e

WALT Industrial Tool Co., 701 East Joppa Road, Towson, MD

21286, call 1-800-4-D

e

WALT (1-800-433-9258) or visit our website:

www.dewalt.com.

COMPATIBLE ACCESSORIES

Oscillating Sanding Pad

Oscillating Wood with Nails Blade

Wide Titanium Oscillating Wood with Nails Blade

Oscillating Hardwood Blade

Oscillating Fastcut Wood Blade

Wide Oscillating Fastcut Wood Blade

Oscillating Wood Detail Blade

Oscillating Titanium Metal Blade

Oscillating Semicircle Blade

Oscillating Titanium Semicircle Blade

Oscillating Flush Cut Blade

Titanium Oscillating Flush Cut Blade

Oscillating Multi-Material Blade

English

14

Oscillating Rigid Scraper Blade

Oscillating Flexible Scraper Blade

Oscillating Carbide Grout Removal Blade

Oscillating Fastcut Carbide Grout Removal Blade

Oscillating Carbide Rasp

Repairs

The charger and battery pack are not serviceable.

To assure product SAFETY and RELIABILITY, repairs, maintenance

and adjustment (including brush inspection and replacement) should

be performed by a D

e

WALT factory service center, a D

e

WALT

authorized service center or other qualified service personnel. Always

use identical replacement parts.

Register Online

Thank you for your purchase. Register your product now for:

• WARRANTY SERVICE: Registering your product will help you

obtain more efficient warranty service in case there is a problem

with your product.

• CONFIRMATION OF OWNERSHIP: In case of an insurance

loss, such as fire, flood or theft, your registration of ownership will

serve as your proof of purchase.

• FOR YOUR SAFETY: Registering your product will allow us to

contact you in the unlikely event a safety notification is required

under the Federal Consumer Safety Act.

Register online at www.dewalt.com/register.

Three Year Limited Warranty

D

e

WALT will repair, without charge, any defects due to faulty materials

or workmanship for three years from the date of purchase. This

warranty does not cover part failure due to normal wear or tool

abuse. For further detail of warranty coverage and warranty repair

information, visit www.dewalt.com or call 1-800-4-D

e

WALT (1-800-

433-9258). This warranty does not apply to accessories or damage

caused where repairs have been made or attempted by others. This

warranty gives you specific legal rights and you may have other rights

which vary in certain states or provinces.

In addition to the warranty, D

e

WALT tools are covered by our:

1 YEAR FREE SERVICE

D

e

WALT will maintain the tool and replace worn parts caused by

normal use, for free, any time during the first year after purchase.

2 YEARS FREE SERVICE ON D

e

WALT BATTERY PACKS

DC9071, DC9091, DC9096, DC9280, DC9360, DC9180,

DCB120, DCB127, DCB201, DCB203, DCB203BT, DCB207

3 YEARS FREE SERVICE ON D

e

WALT BATTERY PACKS

DCB200, DCB204, DCB204BT, DCB205

D

e

WALT BATTERY PACKS

Product warranty voided if the battery pack is tampered with in any

way. D

e

WALT is not responsible for any injury caused by tampering

and may prosecute warranty fraud to the fullest extent permitted by

law.

90 DAY MONEY BACK GUARANTEE

If you are not completely satisfied with the performance of your

D

e

WALT Power Tool, Laser, or Nailer for any reason, you can return

it within 90 days from the date of purchase with a receipt for a full

refund – no questions asked.

LATIN AMERICA: This warranty does not apply to products sold

in Latin America. For products sold in Latin America, see country

specific warranty information contained in the packaging, call the

local company or see website for warranty information.

English

15

FREE WARNING LABEL REPLACEMENT: If your warning labels

become illegible or are missing, call 1-800-4-D

e

WALT (1-800-433-

9258) for a free replacement.

Troubleshooting

Problem Possible Cause Possible Solution

Unit will not start. Battery not

installed.

Install battery in tool

handle.

Battery is not

charged.

Place battery on charger

and install a fully charged

battery pack in tool.

Battery or

power tool is

overheated.

Allow battery and/or

tool to cool after

extended use or replace

overheated battery pack

with a cool one.

Switch is

damaged.

Have switch replaced

at an authorized service

center.

English

16

Déﬁnitions: lignes directrices en

matière de sécurité

Les définitions ci-dessous décrivent le niveau de danger pour

chaque mot-indicateur employé. Lire le mode d’emploi et porter

une attention particulière à ces symboles.

DANGER: indique une situation dangereuse imminente qui,

si elle n’est pas évitée, entraînera la mort ou des blessures

graves.

AVERTISSEMENT : indique une situation potentiellement

dangereuse qui, si elle n’est pas évitée, pourrait entraîner la

mort ou des blessures graves.

ATTENTION : indique une situation potentiellement

dangereuse qui, si elle n’est pas évitée, pourrait entraîner des

blessures légères ou modérées.

AVIS : indique une pratique ne posant aucun risque de

dommages corporels mais qui par contre, si rien n’est fait

pour l’éviter, pourrait poser des risques de dommages

matériels.

POUR TOUTE QUESTION OU REMARQUE AU SUJET DE CET

OUTIL OU DE TOUT AUTRE OUTIL D

e

WALT, COMPOSEZ LE

NUMÉRO SANS FRAIS : 1-800-4-D

e

WALT (1-800-433-9258).

AVERTISSEMENT : afin de réduire le risque de blessures, lire

le mode d’emploi de l’outil.

Avertissements de sécurité généraux

pour les outils électriques

AVERTISSEMENT ! Lire tous les avertissements de

sécurité et toutes les directives. Le non-respect des

avertissements et des directives pourrait se solder par un

choc électrique, un incendie et/ou une blessure grave.

CONSERVER TOUS LES AVERTISSEMENTS

ET TOUTES LES DIRECTIVES POUR UN

USAGE ULTÉRIEUR

Le terme « outil électrique » cité dans les avertissements se rapporte

à votre outil électrique à alimentation sur secteur (avec fil) ou par piles

(sans fil).

1) SÉCURITÉ DU LIEU DE TRAVAIL

a) Tenir l’aire de travail propre et bien éclairée. Les lieux

encombrés ou sombres sont propices aux accidents.

b) Ne pas faire fonctionner d’outils électriques dans un

milieu déflagrant, tel qu’en présence de liquides, de

gaz ou de poussières inflammables. Les outils électriques

produisent des étincelles qui pourraient enflammer la poussière

ou les vapeurs.

c) Éloigner les enfants et les personnes à proximité pendant

l’utilisation d’un outil électrique. Une distraction pourrait en

faire perdre la maîtrise à l’utilisateur.

2) SÉCURITÉ EN MATIÈRE D’ÉLECTRICITÉ

a) Les fiches des outils électriques doivent correspondre

à la prise. Ne jamais modifier la fiche d’aucune façon.

Ne jamais utiliser de fiche d’adaptation avec un outil

électrique mis à la terre. Le risque de choc électrique sera

réduit par l’utilisation de fiches non modifiées correspondant à

la prise.

Français

17

b) Éviter tout contact physique avec des surfaces mises à la

terre comme des tuyaux, des radiateurs, des cuisinières

et des réfrigérateurs. Le risque de choc électrique est plus

élevé si votre corps est mis à la terre.

c) Ne pas exposer les outils électriques à la pluie ou à

l’humidité. La pénétration de l’eau dans un outil électrique

augmente le risque de choc électrique.

d) Ne pas utiliser le cordon de façon abusive. Ne jamais

utiliser le cordon pour transporter, tirer ou débrancher

un outil électrique. Tenir le cordon éloigné de la chaleur,

de l’huile, des bords tranchants et des pièces mobiles.

Les cordons endommagés ou enchevêtrés augmentent les

risques de choc électrique.

e) Pour l’utilisation d’un outil électrique à l’extérieur, se

servir d’une rallonge convenant à cette application.

L’utilisation d’une rallonge conçue pour l’extérieur réduira les

risques de choc électrique.

f) S’il est impossible d’éviter l’utilisation d’un outil

électrique dans un endroit humide, brancher l’outil dans

une prise ou sur un circuit d’alimentation dotés d’un

disjoncteur de fuite à la terre (GFCI). L’utilisation de ce type

de disjoncteur réduit les risques de choc électrique.

3) SÉCURITÉ PERSONNELLE

a) Être vigilant, surveiller le travail effectué et faire preuve

de jugement lorsqu’un outil électrique est utilisé. Ne

pas utiliser d’outil électrique en cas de fatigue ou sous

l’influence de drogues, d’alcool ou de médicaments. Un

simple moment d’inattention en utilisant un outil électrique peut

entraîner des blessures corporelles graves.

b) Utiliser des équipements de protection individuelle.

Toujours porter une protection oculaire. L’utilisation

d’équipements de protection comme un masque antipoussière,

des chaussures antidérapantes, un casque de sécurité ou des

protecteurs auditifs lorsque la situation le requiert réduira les

risques de blessures corporelles.

c) Empêcher les démarrages intempestifs. S’assurer que

l’interrupteur se trouve à la position d’arrêt avant de

relier l’outil à une source d’alimentation et/ou d’insérer

un bloc-piles, de ramasser ou de transporter l’outil.

Transporter un outil électrique alors que le doigt repose sur

l’interrupteur ou brancher un outil électrique dont l’interrupteur

est à la position de marche risque de provoquer un accident.

d) Retirer toute clé de réglage ou clé avant de démarrer

l’outil. Une clé ou une clé de réglage attachée à une partie

pivotante de l’outil électrique peut provoquer des blessures

corporelles.

e) Ne pas trop tendre les bras. Conserver son équilibre en

tout temps. Cela permet de mieux maîtriser l’outil électrique

dans les situations imprévues.

f) S’habiller de manière appropriée. Ne pas porter de

vêtements amples ni de bijoux. Garder les cheveux, les

vêtements et les gants à l’écart des pièces mobiles. Les

vêtements amples, les bijoux ou les cheveux longs risquent de

rester coincés dans les pièces mobiles.

g) Si des composants sont fournis pour le raccordement de

dispositifs de dépoussiérage et de ramassage, s’assurer

que ceux-ci sont bien raccordés et utilisés. L’utilisation

d’un dispositif de dépoussiérage peut réduire les dangers

engendrés par les poussières.

4) UTILISATION ET ENTRETIEN D’UN OUTIL ÉLECTRIQUE

a) Ne pas forcer un outil électrique. Utiliser l’outil électrique

approprié à l’application. L’outil électrique approprié

effectuera un meilleur travail, de façon plus sûre et à la vitesse

pour laquelle il a été conçu.

Français

18

La page charge ...

DeWalt DCK940D2WDCE100 Manuel utilisateur

DeWalt DCK940D2WDCE100 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents