Real Flame C1270LP-BK Manuel utilisateur

!

Warning:

For outdoor use only

DO NOT use for cooking

DO NOT use under any

overhead enclosure

!

Warning:

If the information in this manual is not

followed exactly, a ﬁre or explosion

may result causing property damage,

personal injury or loss of life.

Installation and service must be

performed by a qualiﬁed installer,

service agency or gas supplier.

Improper installation, adjustment,

alteration, service or maintenance can

cause injury or property damage.

Read the installation, operation

and maintenance instructions

thoroughly before installing or

servicing this equipment.

Save these instructions for future

reference. If you are assembling

this unit for someone else, give

this manual to him or her to read

and save for future reference.

!

Designed and Engineer

C US

ed by

Real Flame. Manufactured as

Model # C1270LP

ed in the vicinity of

DANGER

!

If you smell gas:

!

WARNING

An LP-cylinder not connected for use

should not be stor

this or a

ny other appliance.

PO: _____________

LOT: ____________

away from the appliance and

immediately call your gas supplier

or ﬁre department.

1. Shut oﬀ gas to the appliance.

Do not store or use gasoline or other

ﬂammable vapors and liquids in the

vicinity of this or any other appliance.

C1270LP Cavalier

Fire Table Owner’s Manual

3

5

7

8

9

13

14

15

17

20

!

CARBON MONOXIDE HAZARD

This appliance can produce carbon

monoxide which has no odor.

Using it in an enclosed space can kill you.

Never use this appliance in an enclosed

space such as a camper,tent,car or home.

Important Safety Information

Propane (LP) Gas Dangers and Warnings

Hose and Regulator Assembly and Replacement

Parts List

Assembly Instructions

Lighting

Care and Cleaning

Gas Component Connection Checks

T

Warranty

roubleshooting

TABLE OF CONTENTS

DANGER

2

Product Name

Cavalier Fire Table

Model No.

C1270LP

Rated Heat Output

55,000 btu/hr

Type of Gas

Propane (LP)

Gas Supply

20 lb LP-Gas Cylinder

SPECIFICATIONS

!

IMPORTANT SAFETY INFORMATION

WARNING FIRE TABLE IS FOR OUTDOOR USE ONLY

3

• WARNING Failure to follow the dangers, warning and cautions in this manual may result in

serious bodily injury or death, or in a ﬁre or an explosion causing damage to property.

• WARNING Improper installation, adjustment, alteration, service or maintenance can cause

injury or property damage. Read the installation,operating and maintenance instructions

thoroughly before installing or servicing this equipment.

• Minimum Clearence from Unit to Combustible Materials

48” (121.9 cm) from all sides and back. Do not locate this ﬁretable under any overhead

enclosure. Do not place on top of combustible surfaces.

IF YOU SMELL GAS

• Extinguish any open ﬂame.

• Shut o gas supply to the ﬁre table.

• Do not try lighting any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s phone.

• Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the ﬁre department.

• Children and adults should be alerted to the hazards of high surface temperatures and be

kept at a safe distance while ﬁre table is in use.

• This outdoor ﬁre table is NOT to be operated by children. Young children should be

closely supervised when in the vicinity of this outdoor ﬁre table.

• Do not hang or place clothing or other ﬂammable materials on or near the gas ﬁre table.

• Any guard or protective device removed for servicing the appliance shall be replaced prior

to operating the appliance.

• Installation and repair should be done by a qualiﬁed service person. The appliance should

be inspected before use and at least annually by a qualiﬁed service person. More frequent

cleaning may be required as necessary. It is imperative that the control compartment,

burners, and circulating air passageways of the appliance are kept clean.

• Keep these instructions for future reference. If you are assembling this unit for someone

else, give this manual to him or her to read and keep for future reference.

• DO NOT use this unit for cooking.

• DO NOT pour water into the ﬁre table.

• DO NOT use this outdoor ﬁre table if any part has been under water. Immediately call a

qualiﬁed service technician to inspect the ﬁre table and to replace any part or control

system and any gas control which has been under water.

IMPORTANT SAFETY INFORMATION

(Continued)

4

• This gas ﬁre table must be used ONLY outdoors in a well-ventilated space and shall NOT be

used inside a building, garage, or any other enclosed area.

• DO NOT use this outdoor gas ﬁre table for indoor heating. TOXIC carbon monoxide fumes

can accumulate and cause asphyxiation.

• NEVER LEAVE this gas ﬁre table unattended when in use.

• Do not store or use gasoline or other ﬂammable vapors and liquids within 25 feet (7.62m) of

this or any other appliance.

• Do not store any combustible materials in the base enclosure.

• Never use a ﬂame to check for gas leaks.

• The use of alcohol, prescription or non-prescription drugs may impair an individual’s ability

to properly assemble or safely operate this outdoor ﬁre table.

• DO NOT use in an explosive atmosphere. Keep gas ﬁre table area clear and free from

combustible materials, gasoline and other ﬂammable vapors and liquids.

• This outdoor ﬁre table is not to be installed or used in or on recreation vehicles and/or boats.

• Always use in accordance with all applicable local, state and national codes. Contact your local

ﬁre department for details on outdoor burning.

• Use the same precautions you would with any open ﬁre when using this outdoor ﬁre table.

• DO NOT burn solid fuels such as: wood, charcoal briquettes, lump charcoal, manufactured logs,

driftwood, trash, leaves, paper, cardboard, plywood, painted or stained or pressure treated

wood in this outdoor ﬁre table.

• DO NOT use this outdoor ﬁre table until it is COMPLETELY assembled and all parts are securely

fastened and tightened.

• DO NOT store another LP gas tank within 10 feet (3.05 m) of this outdoor ﬁre table while it is

in operation.

• DO NOT use this outdoor ﬁre table near automobiles, trucks, vans or recreational vehicles.

• DO NOT use this outdoor ﬁre table under any overhead structure or near any unprotected

combustible

constructions. Avoid using near or under overhanging trees and shrubs.

• Always use this outdoor ﬁre table on a hard, level non-combustible surface such a concrete,

rock or stone. An asphalt or blacktop surface may not be acceptable for this purpose.

• DO NOT wear ﬂammable or loose clothing when operating this outdoor ﬁre table.

• DO NOT use in windy conditions.

• Keep all electrical cords away from a hot outdoor ﬁre table.

• Certain areas of this outdoor ﬁre table when in use will become too hot to touch. Do not touch

hot surfaces until the unit has cooled unless you are wearing protective gear such as

insulated

pot holders or heat resistant gloves or mittens to avoid burns.

• DO NOT attempt to move or store this outdoor ﬁre table until all parts are cool.

• DO NOT lean over this outdoor ﬁre table when lighting or when in use.

• Use only the regulator and hose assembly provided. The replacement regulator and hose

assembly shall be that speciﬁed by the manufacturer.

• DO NOT attempt to disconnect the gas regulator fro

m the tank or any gas ﬁtting while the

outdoor ﬁre table is in use.

• Always shut o

gas supply at the tank valve and disconnect regulator from the tank when the

ﬁre table is not in use.

• DO NOT sit on the ﬁre table when the unit is in operation.

• DO NOT throw anything onto the ﬁre when the unit is in operation.

• It is essential to keep the outdoor ﬁre table valve compartment, burners, and circulating air

passages clean. Inspect outdoor ﬁre table before each use.

• Lava rocks and glass ﬁllers are very hot; please keep children or pets at a safe distance.

5

IMPORTANT SAFETY INFORMATION

(Continued)

PROPANE (LP) DANGERS AND WARNINGS

!

• Prior to each ﬁre table operation, check the hose for evidence of excessive abrasion or wear.

Use a handheld mirror to see hose sections located under the unit. If the hose is damaged,

cracked or cut, it must be replaced before using the gas ﬁre table. The hose assembly can only

be replaced with a hose assembly speciﬁed by the manufacturer. Please call Real Flame at

1-800-654-1704.

• Before each use, examine the burner and its components. If dirty, clean with a soft brush and

soapy water solution. Also examine the area around the burner. Any dirt or foreign material,

such as spider webs or nests in this area should be removed. If it is evident that the burner is

damaged, the ﬁre table must not be used. The burner assembly must be replaced. Please

contact Real Flame at 1-800-654-1704 for technical support.

• For external tank ﬁre tables, place the hose out of the pathways where people may trip

over it. Do not place the hose in areas where it may be subjected to accidental damage.

WARNING

T

Natural Gas (NG) must be done with the approved Real Flame conversion kit and must be

done by a gas professionial. Failure to do so may result in property damage, injury, or death.

his outdoor ﬁre table is for use with liqueﬁed petroleum (LP) gas only. The conversion to

ATTENTION: Any alteration of the outdoor ﬁre table that is not speciﬁcally

directed in the operations manual will void manufacturer warranty.

LP GAS

LP gas is ﬂammable and hazardous if handled improperly. Become aware of the characteristics

before using any LP gas product.

Propane Characteristics

• Flammable, explosive under pressure, heavier than air and settles in pools in low areas.

• In its natural state, propane has no odor. For your safety, an odorant has been added.

• Contact with propane could burn your skin.

• Propane is extremely ﬂammable and hazardous if handled improperly.

LP GAS WARNINGS

• Cylinders must be stored outdoors in a well-ventilated area out of reach of children.

• Disconnected cylinders must have valve dust caps installed and must not be stored in a

building, garage or any other enclosed area.

• Never use a propane cylinder with a damaged body, valve, collar or footing.

• Dented or rusted propane cylinders may be hazardous and should be checked by your

propane gas supplier.

• Be sure to use only one 20 lb (9.1 kg) LP gas cylinder with a Type 1 valve with this appliance as

required by the American National Standards Institute (ANSI) and the Canadian Standards

Steering Committee.

• Only tanks marked “propane” may be used.

• The LP gas supply tank must be constructed and marked in accordance with the Speciﬁcations

for LP gas LP gas tanks of the U.S. Department of Transportation (DOT) or the National

Standard of Canada, CAN/CSA-B339, LP gas tanks, Spheres and Tubes for the Transportation

of Dangerous Goods; and Commission.

• LP gas tank must be arranged for vapor withdrawal.

6

PROPANE (LP) DANGERS AND WARNINGS

(Continued)

• The LP gas tank must have a listed overﬁlling prevention device (OPD) and a QCCI or Type I

(CGA810) LP gas tank connection.

• The LP gas tank must have a tank collar to protect the tank valve.

Cylinder Valve Outlet and Inlet Connection, ANSI/CGA-V-1-1977, CSA B96.

• The LP gas tank should not be dropped or handled roughly.

• Tanks must be stored outdoors out of the reach of children. Do NOT store in a building,

garage, or any other enclosed area.

• Never store your LP gas tank where temperatures can reach over 125°F.

• Do not store the LP gas cylinder in direct sunlight or near a source of heat or combustion.

• Never keep a ﬁlled LP gas tank in a hot car or car trunk. Heat will cause the gas pressure to

increase, which may open the relief valve and allow gas to escape.

• Place dust cap on valve outlet whenever the LP gas tank is not in use. Only install the type of

dust cap on the LP gas tank valve outlet that is provided with the LP gas tank valve. Other

types of caps or plugs may result in leakage of propane.

a. Do not store a spare LP gas cylinder under or near this appliance.

b. Never ﬁll the LP gas cylinder beyond 80% full.

c. If the information in (a) and (b) is not followed exactly, a ﬁre causing death or serious

injury may occur.

• LP gas cylinders should be ﬁlled only by a certiﬁed LP gas dealer.

• The pressure regulator is set for 11 inches of water column (pressure).

• The normal inlet gas pressure for this outdoor ﬁre table is 11 inches of water column pressure.

• Never attempt to attach this appliance to the self-contained LP gas system of a camper trailer,

motor home or house.

• Always use the pressure regulator and hose assembly provided with the appliance to connect

to a LP gas cylinder. Never connect to an unregulated LP gas supply. For technical support

contact Real Flame at 1-800-654-1704.

• Hand turn the manual gas control valve. Never use tools. If the valve will not turn by hand, do

not try to repair it. Call a Certiﬁed Gas Technician. The use of force or any self attempted repair

may result in a ﬁre or explosion.

• Children and adults should be alerted to the hazards of high surface temperatures and should

stay away to avoid burns or clothing ignition.

• Young children should be carfully supervised when they are in the area of the appliance.

• Clothing or other ﬂammable material should not be hung from the ﬁretable, or placed on or

near the appliance.

• Any guard or other protective device removed for servicing the appliance shall be replaced

prior to opperating the appliance.

• Installation and repair should be done by a qualiﬁed service person. The appliance should be

inspected before use and at least annually by a qualiﬁed service person. More frequent

cleaning may be required as necessary. It is imperative that the control compartment, burners,

and circulating air passageways of the appliance are kept clean.

Connecting your gas cylinder

Before connection, be sure that there is no debris caught in the head of the gas cylinder, head

of the regulator valve or in the head of the burner and burner ports. Connect regulator valve

and hand-tighten ﬁrmly. Disconnect the propane cylinder from the regulator valve when the ﬁre

table is not in use. DO NOT obstruct the ﬂow of combustion air and ventilation air to the burner.

7

HOSE & REGULATOR ASSEMBLY AND REPLACEMENT

1. This ﬁre table comes equipped with a standard LP gas hose and regulator including the

appliance side connection for a CGA No 791 Cylinder Connection Device. The LP gas hose and

regulator supplied with this ﬁre table must be used. Only a hose and regulator speciﬁed by

manufacturer can be used for replacement.

a. The CGA No 791 connection incorporates a magnetic ﬂow limiting device that acts to limit

the ﬂow of gas if a leak is detected between the regulator and the burner valve.

b. If the burner valve is open prior to the LP gas cylinder service valve being opened, the

connection will interpret this free ﬂow of gas to be a leak.

c. The connection safety feature will reduce gas ﬂow from the regulator to the appliance to a

minimal level.

d. Be sure that the burner control valve is closed prior to opening the LP gas cylinder service

valve to ensure that the connection ﬂow limiting device is not triggered mistakenly.

e. If the connection ﬂow limiting device is triggered mistakenly, close the LP gas cylinder

service valve and the burner valve, wait 10 seconds to allow the device to reset, open the

cylinder service valve, then open the burner valve and light the ﬁre table as per lighting

instructions.

2. Be sure to protect the hose from any hot surfaces. Serious danger may result if the hose

contacts any hot surface.

3. Regular maintenance of the hose and regulator:

a. Inspect the hose before each use of the ﬁre table.

Use a handheld mirror to see hose sections

located under the unit.

If the hose shows signs of cracks, abrasions, cuts or damage of any

kind, do not operate the ﬁretable. Fix or replace the hose as required before using the

ﬁretable. For assistance with repair or replacement of the hose, call Real Flame at

1-800-654-1704. Use only replacement parts from the manufacturer.

b. Inspect the seal inside the CGA No 791 service valve on the LP gas cylinder when replacing

the cylinder or at least once per year. If there is any indication of damage, have the seal

replaced by a certiﬁed gas dealer before operating the ﬁre table.

4. Do not use tools to tighten the CGA No 791 connection nut onto the LP gas cylinder service

valve. Hand tighten only.

5. Be careful to not cross the threads on the connection when tightening the CGA No 791

connection on to the LP gas cylinder service valve.

6. “Leak Test” should always be performed after attaching the connection to the LP gas cylinder

service valve. (See “Checking for Leaks” section of this manual on page 12)

7. For the connection of the hose and regulator to the LP tank, refer to the “Connection” section

of the LP gas cylinder section above.

8

PARTS LIST

5

7

4

Box 1

Fire Table Top 12700101 1

Lid 12700103 1

Box 2

Fire Table Base 12700102 1

AA Battery N/A 1

Glass Filler 10001069 1 Box

Protective Cover 12700012 1

NG Conversion Kit 00023102U 1

1

2

3

4

5

6

7

1

3

2

6

9

1.)

ASSEMBLY INSTRUCTIONS

2.) Open the door to place the LP propane tank (a).

Place LP propane tank on the metal tank holder inside the ﬁre

table body (b). Attach safety chain around propane tank to securely

hold it in place (c).

+

-

a

b

Install the AA battery as shown in the diagram below.

c

Once the LP propane tank is properly connected to the LP regulator hose,

close and latch the door to the ﬁre table.

10

Check to make sure there is no debris

in the head of the LP gas tank or in the

head of the regulator valve. Make sure you

check the burner and burner ports as well.

Connect gas line to tank by turning knob

clockwise. Hand tighten only.

Make sure the valve on the LP gas tank is

OFF.

Disconnect by turning the knob counter

clockwise until it is detached from the valve.

3.) Connect the LP Gas Tank

Disconnecting the LP Gas Tank

ASSEMBLY INSTRUCTIONS

11

4.) Place glass ﬁller by hand. DO NOT dump bag out into tray to avoid clogging the burner

with dust. Position the glass ﬁller across the burn area to a level just covering the burner.

Make sure that you do not block the igniter housing with glass ﬁller to ensure proper

ignition.

ASSEMBLY INSTRUCTIONS

Igniter Housing

Lava Rock and Glass Filler Warning:

2.

Do not light or use this ﬁre table if ﬁller is wet. Ensure ﬁller is completely dry before lighting.

Intense heat can cause wet ﬁller to explode and hit someone causing injury.

3. Please keep away from the ﬁre table for at least 20 minutes during initial start-up as ﬁller

could retain some moisture from manufacturing and shipping.

1. Do not overﬁll the burner area with rock or glass ﬁller. The depth of the ﬁller should not be

more than one inch above the burner tube. Only Real Flame ﬁller products have been

certiﬁed and tested by CSA for safe use with this Real Flame ﬁre table. Using other ﬁller

material may result in increased popping/ and cracking or increased CO gas emission.

12

PRE-USE INSTRUCTIONS

Prior to each gas ﬁre table operation, check the hose and valve for evidence of excessive

abrasion or wear.

CHECKING FOR LEAKS

Ma

Make a leak check solution by mixing 1 part dishwashing

soap with 3 parts water in a spray bottle.

ke sure control knob is OFF. Then, turn LP gas tank

to ON at valve.

Spray leak solution on valve connections paying particular

attention to the areas indicated by arrows.

If any bubbles appear turn LP gas tank OFF, reconnect and

re-test. If you continue to see bubbles after

several attempts, disconnect LP gas source and

contact Real Flame at 1-800-654-1704 for assistance.

If no bubbles appear after one minute turn tank OFF, wipe

away solution and proceed.

Check for leaks at these locations.

WARNING Before using this outdoor ﬁre table, make sure you have read, understand and

are following all information provided in the important Safety Information section of this

manual. Failure to follow those instructions can cause death, serious injury or property damage.

!

13

LIGHTING INSTRUCTIONS

HI

OFF

LIGHT

LOW

Control Knob

PUSH

IN

1. Read and understand all operating instructions before lighting.

2. Burner control knob must be in the OFF position.

3. Connect propane (LP) cylinder (see above pages).

4. Slowly open valve on LP gas cylinder.

5. Push and hold igniter button

6. While holding the igniter button with one hand, use

your other hand to push and turn the control knob

to the LIGHT position to light the burner.

7. Keep Burner Control Knob pressed in for 15-30 seconds after ignition.

8. If ignition does not occur in 30 seconds, turn control knob to the OFF position and turn

gas o at the source, wait 5 minutes until gas has cleared and repeat lighting procedure.

Please refer to the trouble shooting pages for

additional support, beginning on page 17.

Using the igniter

WARNING

When using this method to light

your ﬁre table use heat resistant

gloves and follow the step by step

instructions. Failure to do so could

result in severe injury.

9. After lighting, rotate the Burner Control Knob counter clockwise to LOW setting.

10. Adjust the ﬂame to the desired height with the

control knob.

WARNING

If burner ﬂame goes out during operation,

immediately turn the control knob OFF and let the

gas clear a minimum of 5 minutes before attempting

to re-light the ﬁre table.

Observe ﬂame, make sure all burner ports are lit. Flame height should be no higher than

13 inches tall.

!

8-13”

20.3 - 30.5 cm

1. Wearing heat-resistant gloves, position the burning

long match or extended lighter near the side of

the burner. DO NOT lean over the ﬁre table while

lighting.

2. Turn control knob counterclockwise to LIGHT.

3. Remove long match/extended lighter.

4. After lighting, rotate the burner control knob counter

clockwise to LOW setting. Observe ﬂame; make sure

all burner ports are lit.

5. Adjust the ﬂame to the desired height with the

control knob.

6. Replace the battery as soon as possible.

If battery is dead you may TEMPORARILY use

a long match or extended butane lighter

If doing so:

14

CARE AND CLEANING

Inspecting

WARNING

DO NOT USE SOLVENTS while in closed spaces or while smoking.

!

product life.

1. Make sure all parts are securely fastened in place. If a part moves when touched, check its connection points to

see if they are lose.

WARNING DO NOT tamper with this appliance. This is DANGEROUS and will void the warranty. Any part found

Real Flame at: 1-800-654-1704.

2. Check all gas connections for leaks.

3. Check ignition system to insure proper sparking.

4. Check components for any signs of damage, rust or excessive wear.

5. If damage to any component is detected, DO NOT operate until the proper repairs have been made.

cool to the touch.

General Care and Cleaning

WARNING

DO NOT use oven cleaner or abrasive cleaners as they will damage this product.

1. Wipe exterior surfaces with a mild dishwashing soap, then rinse clean with water.

Storage:

WARNING

1. Turn gas OFF at tank connection. Remove tank and store in a cool, dry location outdoors, away from children.

2. Carefully remove ller and store components at to protect them from breakage.

3. ALWAYS cover your outdoor re table when not in use. The cover will protect the mechanical components

from dirt and debris, prevent water from pooling on surface of the re table and will prevent fading and

discoloration of the nish.

4. Store in a cool, dry location away from children and pets.

Table

DO NOT inspect this outdoor re table until the re is COMPLETELY out.

This outdoor re table must be inspected regularly to ensure that the product is safe to use and to extend

be faulty must be replaced with an approved part, conrmed by the manufacturer. For technical support contact

1. This outdoor re table should be cleaned regularly to ensure safe use and extended product life.

NOTE: After repeated use, a slight discoloration of the nish may occur.

DO NOT attempt to clean this outdoor re table unless the re is completely out and the unit is

15

GAS COMPONENT CONNECTION CHECKS

If the burner will not light or stay lit, please perform the following checks.

1. Make sure the electrode wire is completely and correctly connected.

2. Make sure that the electronic ignition is unobstructed.

Clear any debris on top of the igniter housing and make sure there is no debris

between the igniter pin, thermocouple and the burner tube.

Back of

Electronic

Ignition

Igniter Housing

Burner

Tube

Do not block

opening

CORRECT

INCORRECT

5mm

Thermocouple

Ignitor Pi

n

16

GAS COMPONENT CONNECTION CHECKS

3. Make sure that the igniter pin and thermocouple are correctly positioned.

- The igniter pin should be pointed at the thermocouple.

- The thermocouple should be positioned 5mm away from the burn tube.

4. Make sure that the thermocouple wire is correctly positioned. The thermocouple

wire should be in line with the valve.

Thermocouple Wire

Wire should

be in line

with valve

Valve

Electronic Ignition

Thermocouple

Wire

Valve

17

TROUBLESHOOTING

Possible Cause 1: No Gas Flow.

-Check if the LP gas tank is empty. If empty, replace and reﬁ ll. If the propane

tank is not empty, refer to “Problem: Sudden drop in gas ﬂ ow” on the

following page.

Possible Cause 2: Coupling nut and regulator not fully connected.

-Turn the coupling nut about one half to three fourths of a turn, until you

feel a solid stop. Do not use tools, tighten by hand only.

Possible Cause 3: Obstruction of gas ﬂ ow.

- Check for bent or kinked hose.

Possible Cause 4: Spider webs or insect nest in the Venturi.

- Clean the Venturi using compressed air.

Possible Cause 5: Burner ports clogged or blocked.

-Reference “Problem: Irregular ﬂ ame pattern” on the

following page. Clean the burner

ports as described there.

Possible Cause 1: Electrode and burners are wet.

-Wipe dry with cloth.

Possible Cause 2: Igniter battery is dead or backwards.

-Check that the AA battery is inserted correctly in the igniter (see page 9) or replace the

battery.

Possible Cause 3: Igniter Pin cracked or broken - sparks at crack.

-Call Real Flame at 1-800-654-1704 for technical support.

Possible Cause 4: Wire loose or disconnected.

-Reference page 16, step 1, reconnect wire. Call Real Flame at 1-800-654-1704.

Possible Cause 5: Wire is shorting (sparking) betw een igniter and electrode.

-Call Real Flame at 1-800-654-1704 for support.

Possible Cause 6: Igniter Pin not pointing at thermocouple.

-Reference page 16, turn electrode to point at

the thermocouple.

Possible Cause 7: Bad Igniter.

-Call Real Flame at 1-800-654-1704 for

support.

Problem: Burner will not light using igniter

Problem: The Fire Table emits a lot of black smoke when in use

Problem: Burner will not light with match

Possible Cause 1: Hose from gas ﬁ re table is pinched.

-Make sure the hose is not pinched between the ﬁre table and the source of the gas.

Possible Cause 2: Flame is being obstructed at burner ports.

-Make sure that the gas ports on the burner are free of any ﬁller so that the ﬂame

For Technical Support Contact Real Flame at: 1-800-654-1704

can ﬂow naturally.

Venturi Opening

18

Possible Cause: Burner ports are clogged or blocked.

-Clean burner ports.

Do this by inserting a paperclip into each of the burner ports to ensure they are

not clogged.

WARNING: Make sure burner is not on and the gas supply has been properly

disconnected. Allow 15 minutes for unit to cool before touching it.

If these troubleshooting steps are unable to resolve the problem,

please call Real Flame at: 1-800-654-1704

Possible Cause 1: High or gusting winds.

-Do not use ﬁre table.

Possible Cause 2: Low on LP gas.

-Replace or reﬁ ll LP gas tank.

Possible Cause 3: Excess ﬂ ow valve tripped.

-Refer to “Problem: Sudden drop in gas ﬂ ow”

Possible Cause 1: Ice has built up on the outside of the LP gas tank because the

vaporization process is too low.

-Turn the control knob and the LP gas tank to OFF. Replace with a spare LP

gas tank and resume burning. Store the spare LP gas tank in a well ventilated

area, away from children.

Possible Cause 1: Out of gas.

- Reﬁll or exchange your LP tank.

Possible Cause 2: Excess ﬂ ow safety device may have been activated.

-

if the ﬂame goes out. In order for the unit to work, ﬂames must be contacting the

thermocouple located in the igniter housing. Visually inspect the thermocouple and

igniter housing to make sure there are no obstructions, such as glass ﬁller or lava rock,

and that ﬂames are contacting the thermocouple.

Problem: Sudden drop in gas ﬂ ow, or a reduced ﬂ ame height

Problem: Irregular ﬂ ame pattern, ﬂ ame does not run the full length of the burner

Problem: Flame blow out

Problem: Flame seems to lose heat when burning in cold weather -

temperature below 50°F

TROUBLESHOOTING

19

TECHNICAL PARTS LIST

LP Hose and Regulator

12700013

Igniter Housing

12700007

Burn Tube

12700004

Burn Pan

12700005

Electronic Ignition

12700011

Thermocouple

12700008

Oriﬁce Spud

12700010

Control Knob

115640006

Valve

12700009

Fire Table

Bellows (CSST)

12700006

Igniter Electrode

12700014

Conversion Kit

00023102U

Warranty & Return Policies

Real Flame®

7800 Northwestern Ave.

Racine, WI 53406

Customer Service: 1-800-654-1704 in USA

Service à la clientèle: 1-800-363-6443 in Canada

custserv@realﬂame.com

Warranty

Real Flame® Company warrants Real Flame ﬁreplaces and accessories to be free from defects

in parts under normal use and service for a period of 1 year from the date of purchase and

defective from ﬁnish issues for a period of 1 years from the date of purchase. In the event of such

defects Real Flame will, at its option, replace the defective product or refund the purchase price.

The foregoing is the exclusive remedy and Real Flame disclaims all other warranties, including any

implied warranty of merchantability or ﬁtness for a particular purpose. In addition, Real Flame will

not be responsible for consequential damages in excess of the purchase price of the product on

which such liability is based.

Return Policy

You may return your purchase within 90 days of receipt. No refunds will be issued f

or incomplete

or unauthorized returns. All returned products must be 100% complete, adequately packaged in

original packaging and in resalable condition. Products that have been assembled or modiﬁed will

not be eligible for return. All items must be returned in their entirety, meaning all items included

must be returned together. No returns or exchanges on discontinued items. Please begin the return

process by contacting the store or company where you bought your Real Flame item.

Replacement Parts

In the event that an item has been lost or damaged, either by the manufacturer or in shipping, you

may request a replacement. Replacement parts are not available for all units and only given at Real

Flame’s discretion. We will assess any damage and ﬁnd a solution, which could include shipping

you a replacement. No replacements are available for discontinued items or repac

kaged (open

box) products. Please call Real Flame Customer Service at 800-654-1704 for replacement parts

before returning the damaged item. Please have the following information (which can be found in

your instruction manual) ready before you call Customer Service.

• Model Number of Item

• 4-8 digit Part Number

• Lot Code Number

• Shipping Address

• A picture of the damaged item may be requested. Pictures should be

sent to custserv@realﬂame.com

Incorrect Order Received

If you received something other than what you ordered, please contact Real Flame Customer

Service at 800-654-1704 within 48 hours of receiving the item.

Please refer to www.Realﬂame.com for our complete return guidelines and policies.

La page charge ...

Real Flame C1270LP-BK Manuel utilisateur

Real Flame C1270LP-BK Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents