KitchenAid KUDK03CTWH0 Guide d'installation
- Taper
- Guide d'installation
KitchenAid _
HOME APPLIANCES
Installation instructions
Undercounter Dishwasher
instructions d'installation
Lave-vaisselle encastr_
Table of Contents ............................................................................. 2
Table des matieres ......................................................................... 20
W10078153B
Table of Contents
Dishwasher Safety ................................. 2
Installation Requirements ........................... 3
Tools and parts ................................. 3
Location Requirements .......................... 3
Drain Requirements ............................. 5
Water Supply Requirements ...................... 5
Electrical Requirements .......................... 5
installation Instructions ............................. 6
Prepare cabinet opening
using existing utility hookups ..................... 6
Prepare cabinet opening
where there are no existing utility hookups .......... 7
Install moisture barrier ........................... 9
Prepare dishwasher ............................ 10
Make electrical connection ...................... 16
Connect to water supply ........................ 17
Connect to drain ............................... 18
Secure dishwasher in cabinet opening ............. 18
Dishwasher Safety
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Tip Over Hazard
Do not use dishwasher until completely installed.
Do not push down on open door.
Doing so can result in serious injury or cuts.
You need to:
o Slowly open dishwasher door while someone grasps the
rear of the dishwasher. Remove shipping materials, drain
hose and lower rack. Close dishwasher door until latched.
Observe all governing codes and ordinances.
Install this dishwasher as specified in these instructions.
Installation should be performed by a qualified service
technician.The dishwasher must be installed to meet all
electrical and plumbing national and local codes and
ordinances.
installation Requirements
Tools and Parts
Gather the required tools and parts before starting
installation.
All installations
Tools needed:
o pliers
o Phillips screwdriver
,5/16" and 1/4" nut drivers
or hex sockets
measuring tape or ruler
10" adjustable wrench that
opens to 1-1/8" (2.9 cm)
flat-blade screwdriver
utility knife
2 twist-on wire connectors
which are the proper size to
connect your household
wiring to 16-gauge wiring
in dishwasher
small level
_TORX"_T15 screwdriver (if
installing custom front
panels)
flashlight
shallow pan
5/8" open-end wrench
bath towel
, wood block
Parts needed:
,90 ° elbow with 3/8" N.RT.
external threads on one
end. (The other end must
fit your water supply line.)
,Teflon <_tape or pipe joint
compound
, shims (if installed with
built-up floor)
,4 #10 x 1/2" wood screws
(if installing custom front
panels)
In addition, for new installations
Tools needed:
* electric drill with 1/2", 3/4"
and 1-1/2" hole saw bits
* small tubing cutter
wire stripper
1-1/2"-2" screw-type clamp
if connecting to waste-tee
Parts needed:
* copper tubing (3/8"
recommended) or flexible
stainless steel braided fill
line
clamp connector or
conduit connector to fit a
7/8" (2.2 cm) diameter hole
Parts supplied
A. 2- drain hose clamps, 1 large and 1 small
B. 2- # 10 x 1/2" Phillips-head screws
C. drain hose
B
Additional parts supplied with top-venting models only
D. 2 #8 x 1-3/8"TORX_T15 screws
E. 4 #10 x 3/8" hex-head screws
Additional part supplied with certain models
E Bottom sound pad (located in lower rack)
G. Moisture barrier tape
Make sure all these parts are included. If not included, call
1-800-422-1230.
See separate parts list for accessories available for your
dishwasher.
_)Teflon is a registered trademark of E.I. Du Pont de Nemours and
Company.
_) Registered trademark of TEXTRON.
Location Requirements
Do not run drain lines, water lines or electrical wiring where
they can interfere with or contact dishwasher motor or legs.
The location where the dishwasher will be installed must
provide clearance between motor and flooring. Motor
should not touch the floor.
Do not install dishwasher over carpeted flooring.
Protect dishwasher and water lines leading to dishwasher
against freezing. Damage from freezing is not covered by
the warranty.
A side panel kit is available from your dealer for installing
your dishwasher at the end of your cabinetry.
A moisture barrier accessory (Part No. 4396277) is available
from your dealer for installing underneath the countertop,
but is not required.This may also be obtained by calling
1-800-422-1230.
Check location where dishwasher will be installed.The
location must provide:
easy access to water, electricity and drain.
convenient access for loading and unloading dishes.
Corner locations require a 2" (5.1 cm) minimum clearance
between the side of the dishwasher door and the wall or
cabinet.
square opening for proper operation and appearance.
cabinet front perpendicular to floor.
level floor. (If floor at front of opening is not level with
floor at rear of opening, shims may be needed to level
dishwasher.)
NOTE:To prevent shifting during dishwasher operation,
shims must be securely attached to the floor.
If dishwasher will be left unused for a period of time or in a
location where it may be subject to freezing, have it
winterized by authorized service personnel.
Make sure pipes, wires and drain hose are within the
shaded area shown in the "Cutout dimensions" section.
HelpfulTip: If the floor in the dishwasher opening is
uneven (example: tile flooring only partway into
opening) you will need to take special care in measuring
dimensions and in leveling dishwasher.
Product dimensions
3/4" (1.9 cm)--:_
insulation -
may be
compressed
(not used on
all models)
24-7/8" (63.2 cm) -_
I I front vent
24-1/2" (62.2 cm) _ _11 v/
IIII 33-7/8"
III I (86cm)min.
III I withwheels
_ removed
_e-21" (53.3 cm)-_
SIDE VIEW
23-7/8" (60.6 cm)
REAR VIEW
Cutout dimensions
(5.1 cm) 10"
(25.4
2-3/4" 3-1/4"
(7 cm) (8.3 cm) (8.3 cm) (7 cm)
Cut holes in shaded area of cabinet walls or floor as specified below:
water line- 1/2" (1.3 cm)
drain line- 1-1/2" (3.8 cm)
direct wire - 3/4" (1.9 cm)
power supply cord - 1-1/2" (3.8 cm)
34"
(86.4 cm)
min.*
r_
* Measured from the lowest point on the underside of countertop. May be
reduced to 33-7/8" (86 cm) by removing wheels from dishwasher.
** Minimum, measured from narrowest point of opening.
*** May be increased to 6-5/8" (16.6 cm) if height of opening is 34-1/2"
(876 cm) at its lowest point.
Drain Requirements
o Use the new drain hose supplied with your dishwasher.
If this is not long enough, use a new drain hose with a
maximum length of 12 feet (3.7 m) that meets all current
AHAM/IAPMO test standards, is resistant to heat and
detergent, and fits the 1" (2.5 cm) drain connector of the
dishwasher.
Connect drain hose to waste tee or disposer inlet above
drain trap in house plumbing and 20" (50.8 cm)
minimum above the floor. It is recommended that the
drain hose either be looped up and securely fastened to
the underside of the counter, or be connected to an air
gap.
air gap
Use an air gap if the drain hose is connected to house
plumbing lower than 20" (50.8 cm) above subfloor or
floor.
, Use 1/2" minimum I.D. drain line fittings.
Water Supply Requirements
,A hot water line with 20-120 psi (138-862 kPa) water
pressure.
120°F (49°C) water at dishwasher.
3/8" O.D. copper tubing with compression fitting or
flexible stainless steel braided fill line (1/2" minimum
plastic tubing is not recommended).
A 90° elbow with 3/8" N.RT. external pipe threads on one
end.
Do not solder within 6" (15.2 cm) from water inlet valve.
Electrical Requirements
Contact a qualified electrician.
Assure that the electrical installation is adequate and in
conformance with all national and local codes and
ordinances.
You must have:
120-volt, 60 Hz, AC-only, 15 or 20 amp., fused electrical
supply.
o Copper wire only.
We recommend:
,A time-delay fuse or circuit breaker.
A separate circuit.
If direct wiring dishwasher:
Use flexible, armored or non-metallic sheathed, copper
wire with grounding wire that meets the wiring
requirements for your home and local codes and
ordinances.
Use strain relief method provided with house wiring
junction box or install a U.h-listed/CSA-certified clamp
connector to the house wiring junction box. If using
conduit, use a U.h-listed/CSA-certified conduit connector.
if connecting dishwasher with a power supply cord:
, Use Power Supply Cord Kit (Part No. 4317824) marked for
use with dishwashers. Kit contents include:
-Volex, Inc., UL listed 16 gauge 3 wire power supply cord
with 3 prong grounded plug.
- Neer C-500 7/8 inch strain relief.
- 3 wire connectors.
- Part No. 302797 grommet
Follow the kit instructions for installing the power supply
cord.
, Power supply cord must plug into a mating three prong,
grounded outlet, located in the cabinet next to the
dishwasher opening. Outlet must meet all local codes and
ordinances.
Installation Instructions
Electrical Shock Hazard
Disconnect electrical power at the fuse box or circuit
breaker box before installing dishwasher.
Failure to do so can result in death or electrical shock.
1. Disconnect power.
2. Turn off water supply.
Prepare cabinet opening using
existing utility hookups
o Follow the steps in this section if you are installing the
dishwasher in an existing cabinet opening with utility
hookups.
If you are installing the dishwasher in a cabinet opening
that does not have hookups, follow the steps under
"Prepare cabinet opening where there are no existing
utility hookups" section.
1. Check that the water
line reaches to the
front left of opening
where the water
connection will be
made.
2. Check that the direct
wire reaches to the
front right of opening 6" (15.2cm)
where the electrical ......._
connection will be made.
If the water line and the direct wire reach far enough into
the opening, proceed to the next section "Install the drain
hose:' If they do not reach far enough, follow the steps
under "Prepare cabinet opening where there are no existing
utility hookups."
Instal[ the drain hose
iMPORTANT: Always use a new drain hose even when
installing a new replacement dishwasher.
1. Drill a 1-1/2" (3.8 cm) diameter hole in cabinet wall or
floor on the side of the opening closest to the sink.
2. Connect drain hose to waste tee or waste disposer using
one of the following methods:
Option 1,Waste disposer - with air gap
Option 2, No waste disposer- with air gap
Option 3,Waste disposer - no air gap*
Option 4, No waste disposer- no air gap*
_an air gap is recommended
HelpfuITip:To reduce the vibration of the hose, keep the
hose away from the floor and the edge of the hole where
it passes through the cabinet.
Option 1:Waste disposer- with air gap:
1. Remove the disposer knockout plug. Cut end of drain
hose if needed (do not cut ribbed section).
2. Attach drain hose to air gap with large spring-type
clamp, if the drain hose was cut, use a 1-1/2" to 2"
(3.8 to 5 cm) screw-type clamp*.
3. Use a rubber hose connector* with spring or screw-type
clamps* to connect air gap to disposer inlet.
This connection must be before the drain trap and at
least 20" (50.8 cm) above the floor where dishwasher will
be installed.
drain hose -
cut here if needed
rubber hose
connector
gap
large
spring-type
clamp
hose
drain trap
4.
Insert drain hose through
hole cut in cabinet to the
front center of opening
where drain connection
will be made.
drain hose
.2Parts available from local plumbing supply stores
Option 2: No waste disposer - with air gap:
1. Cut end of drain hose if needed (do not cut ribbed
section).
2. Attach drain hose to air gap with large spring-type
clamp. If the drain hose was cut, use a 1-1/2" to 2"
(3.8 to 5 cm) screw-type clamp*.
3. Use a rubber hose connector* with spring or screw-
type clamps* to connect air gap to waste tee.
This connection must be before the drain trap and at
least 20" (50.8 cm) above the floor where dishwasher
will be installed.
drain hose-
cut here if needed
rubber hose
connector
gap
drain trap_
large
spring-type
drain
hose
4,
drain hose
Insert drain hose
through hole cut in
cabinet to the front
center of opening where
drain connection will be
made.
* Parts available from local plumbing supply stores
Option 3: Waste disposer - no air gap:
1. Remove the disposer knockout plug. Do not cut end of
drain hose.
2. Attach drain hose to disposer inlet with large spring-
type clamp.
This connection must be before the drain trap and at
least 20" (50.8 cm) above the floor where dishwasher
will be installed, it is recommended that the drain hose
be looped up and securely fastened to the underside of
the counter.
large spring-type
clamp
hose
3, Insert drain hose
through hole cut in
cabinet to the front
center of opening where
drain connection will be
made.
drain hose
Option 4: No waste disposer - no air gap:
1. Cut end of drain hose if needed (do not cut ribbed
section).
2. Attach drain hose to waste tee with 1-1/2" to 2"
(3.8 to 5 cm) screw-type clamp*.
This connection must be before the drain trap and at
least 20" (50.8 cm) above the floor where dishwasher will
be installed. It is recommended that the drain hose be
looped up and securely fastened to the underside of the
counter.
drain hose -
_ cut here if needed
waste f 1 f _ "_
tee _ I [_f-_ I _.
I _1 I E_ drain
[ k_ J!_ N hose
3,
Insert drain hose through
hole cut in cabinet to the
front center of opening
where drain connection
will be made.
2 Parts available from local plumbing
supply stores
drain hose
Prepare cabinet opening where there
are no existing utility hookups
Electrical connection
Option1: Direct wire method:
HelpfulTip:Wiring the dishwasher will be easier if you
route wire into the cabinet opening from the right side.
1. Drill a 3/4" (1.9 cm)
hole in right-hand optional preferred
cabinet side, rear or locations locations
floor. Preferred and
optional locations are
shown.
2. Wood cabinet: Sand
hole until smooth.
Metal cabinet: Cover
hole with grommet,
not provided.
3. Run wire into house wiring junction box.
4. Install a U.L.-listed/CSA-certified clamp connector (strain
relief) for flexible-type wire. If installing conduit, attach a
5,
U.L.-listed/CSA-certified
conduit connector to the
junction box.
Run other end of wire
through cabinet hole.
must extend to the right
front of cabinet opening.
Option2: Power supply cord method:
NOTE: A mating, three prong, ground-type wall receptacle is
required in a cabinet next to the dishwasher opening.
1. Drill a 1-1/2"
(3.8 cm) hole in
the cabinet rear
or side. Preferred
and optional
locations are
shown.
2. Wood cabinet:
Sand hole until
smooth.
optional preferred I
locations locations
w
Metal cabinet: Cover hole with grommet (Part No.
302797) included with power supply cord kit.
Install the water line
1,
HelpfuITip: Routing the water line through the left side
of cabinet opening will make water connection easier.
Drill a minimum 1/2" (1.3 cm) hole in the cabinet side,
rear or floor. Preferred and optional locations are shown.
2,
3,
4,
5,
6,
Measure overall length copper
of copper tubing tubing
req uired.
Attach copper tubing
to the water line with a
manual shutoff valve.
Slowly feed copper
tubing through hole in
cabinet. Copper tubing will bend and kink easily, so be
gentle. The copper tubing should be far enough into the
cabinet opening to connect it to dishwasher inlet on the
front left of the dishwasher.
Turn water shutoff valve to "ON" position. Flush water
into a shallow pan to get rid of particles that may clog
the inlet valve.
Turn shutoff valve to "OFF" position.
Install the drain hose
iMPORTANT." Always use a new drain hose.
1. Drill a 1-1/2" (3.8 cm)
diameter hole in cabinet
wall or floor on the side
of the opening closest
to the sink.
2. Connect drain hose to
waste tee or waste disposer using one of the following
methods:
o Option 1,Waste disposer- with air gap
Option 2, No waste disposer- with air gap
o Option 3,Waste disposer- no air gap*
o Option 4, No waste disposer- no air gap*
*an air gap is recommended
Helpful Tip: To reduce the vibration of the hose, keep the
hose away from the floor and the edge of the hole where
it passes through the cabinet.
Option 1:Waste disposer- with air gap:
1. Remove the disposer knockout plug. Cut end of drain
hose if needed (do not cut ribbed section).
2. Attach drain hose to air gap with large spring-type
clamp. If the drain hose was cut, use a 1-1/2" to 2"
(3.8 to 5 cm) screw-type clamp*.
3. Use a rubber hose connector* with spring or screw-type
clamps* to connect air gap to disposer inlet.
This connection must be before the drain trap and at
least 20" (50.8 cm) above the floor where dishwasher will
be installed.
drain hose -
cut here if needed
rubber hose
connector
gap
large
spring-type
clamp
hose
drain trap
4,
Insert drain hose through
hole cut in cabinet to the
front center of opening
where drain connection
will be made.
* Parts available from local plumbing
supply stores
drain hose
Option 2: No waste disposer - with air gap:
1. Cut end of drain hose if needed (do not cut ribbed
section).
2. Attach drain hose to air gap with large spring-type
clamp. If the drain hose was cut, use a 1-1/2" to 2"
(3.8 to 5 cm) screw-type clamp*.
3. Use a rubber hose connector* with spring or screw-type
clamps* to connect air gap to waste tee.
This connection must be before the drain trap and at
least 20" (50.8 cm) above the floor where dishwasher will
be installed.
drain hose-
cut here if needed
rubber hose
connector
gap
large
spring-type
drain
drain trap _ hose
4,
Insert drain hose
through hole cut in
cabinet to the front
center of opening where
drain connection will be
made.
drain hose
* Parts available from local plumbing supply stores
Option 3: Waste disposer - no air gap:
1. Remove the disposer knockout plug. Do not cut end of
drain hose.
2. Attach drain hose to disposer inlet with large spring-type
clamp.
This connection must be before the drain trap and at
least 20" (50.8 cm) above the floor where dishwasher will
be installed. It is recommended that the drain hose be
looped up and securely fastened to the underside of the
counter.
large spring-type
clamp
_ain hose
3, Insert drain hose
through hole cut in
cabinet to the front
center of opening where
drain connection will be
made.
drain hose
Option 4: No waste disposer - no air gap:
1. Cut end of drain hose if needed (do not cut ribbed
section).
2. Attach drain hose to waste tee with 1-1/2" to 2"
(3.8 to 5 cm) screw-type clamp*.
This connection must be before the drain trap and at
least 20" (50.8 cm) above the floor where dishwasher will
be installed. It is recommended that the drain hose be
looped up and securely fastened to the underside of the
counter.
drain hose -
____ cut here if needed
iiiii
3,
Insert drain hose through
hole cut in cabinet to the
front center of opening
where drain connection
will be made.
2 Parts available from local plumbing
supply stores
drain hose
install moisture barrier ion some models)
1. Make sure the area under the cabinet is clean and dry
for installation of the moisture barrier.
2. Remove the backing of the moisture barrier and apply to
underside of the countertop along the front edge of the
counter.
Prepare dishwasher
Tip Over Hazard
Do not use dishwasher until completely installed.
Do not push down on open door.
Doing so can result in serious injury or cuts.
Excessive Weight Hazard
Use two or more people to move and install
dishwasher.
Failure to do so can result in back or other injury.
1. Put corner posts from packaging behind dishwasher.
Grasp sides of dishwasher door frame and put
dishwasher on its back, resting on top of the corner posts.
2. Remove two screws attaching access panel and lower
panel to dishwasher using a 1/4" hex socket, nut driver or
Phillips screwdriver.
lower
panel
clip
3. Remove panels and set panels
aside on a protective surface.
4. Check that grounding clip is
attached to the lower panel.
5. ApplyTeflon® tape or pipe
joint compound to 90° elbow
fitting and connect fitting to
water inlet valve.
6. Tighten elbow until snug, and
be sure that it faces to the rear.
water inlet valve
7. Remove terminal box cover.
- If you are direct wiring: install a U.L.-listed/CSA-
certified clamp connector to the terminal box. If using
conduit, use a U.L.-listed/CSA-certified conduit
connector.
- If you are installing a power supply cord kit, do so
now, following kit instructions.
box cover
dishwasher wires
clamp
connector
8.
Helpful Tip: Put cardboard under dishwasher until it is
installed in cabinet opening.The cardboard will help
protect floor covering during
installation.
Measure height of cabinet opening ] I J_ I
from underside of countertop to floor _ I | I I_
where dishwasher will be installed _l I | L/
(you need the lowest point). Check L | l
chart for that height opening Put
wheels in the required position. _ '_
Number of
Minimum Wheel
turns on
cutout height position front leg
34" (86.4 cm) 1 10
34-1/4" (87 cm) 2 5
34-1/2" (87.6 cm) 3 0
9.
Turn both front leveler legs to the same
height.
If the minimum cutout height is less than
34" (86.4 cm), the rear wheels can be
removed for additional clearance.This will
allow the dishwasher to fit into a 33-7/8"
(86 cm) high cutout, but the dishwasher will
be more difficult to move into position. If
the wheels are removed, protect the floor
when moving the dishwasher.
front leg
If you have built-up floors
1. Measure height of opening
from underside of countertop
to built-up floor. If the height
is at least 33-3/4" (85.7 cm),
the dishwasher will fit into
the opening without
modification to the
countertop or flooring.
2. Put wheels in position 1 and
turn the front leveler legs up
all the way.
j countertop
Ir
33-3/4"
(85.7 cm)
min.
• / /bWIto?
10
3,
Add shims as needed in the area shown to bring
dishwasher up to proper height.
NOTE: Shims must be securely attached to floor to
prevent their movement when the dishwasher is
operated.
shim
2"
(5.1 cm)
2-3/4" 6" 2-3/4"
(Z0 cm) (15.2 cm) (7.0 cm)
Install the door handle (on some models)
iMPORTANT: Do not scratch the front panel during this
procedure.
1. Remove the door handle and hardware bag containing
the setscrews and Allen wrench from the cardboard box.
2. Start set screws in handle.
3. Place handle on mounting studs with the set screws
facing down.
4. Push the door handle tightly against the door. Insert the
short end of the Allen wrench into the setscrews.Tighten
the setscrews 1/4 turn past snug. Retain Allen wrench with
Installation Instructions.
mounting
stud
/
, handle
setscrew
(in bottom
of handle)
..._.)
wrench
Install the door handle--Pro Line _ series
1,
2.
3,
Remove the Pro Line _series handle and two screws from
handle package.
Make sure plastic
spacers are still attached
to the door.
Attach the handle to the
factory-supplied full
front panel as shown.
j_t.- -ft
plastic spacers L_J-_
Install door panel--Pro Line _ series
For top vented models with a factory-supplied stainless or
painted full front panel:
1. Remove the carton containing the factory-supplied full
front panel.
2. Remove the handle package from the front of the
shipping base.
3. With aTORX _screwdriver, remove three screws on both
sides, as shown; hold the outer panel up while removing
the screws. Save screws for reinstallation.
4. Gently set outer panel aside.
3 screws
outer
5. Lay the factory-supplied full front panel face down on a
protective non-scratching surface.
6. Place the outer panel on the back of the full front panel;
align screw holes.
7. Attach outer panel to full front panel panel with the four
#10-16 x 3/8" hex head screws supplied in the literature
package.
I
4 screws
I
hesXrheead
full front panel
outer panel
top edge
8,
Attach the panel assembly to the door by reinstalling the
two uppermost side screws; do not tighten screws
completely.This will hold the panel assembly in place on
the door frame.
2 screws
factory-supplied
full front panel
11
9. Installthetwo#8-18x1-3/8"screwsfromtheliterature
packageinthetopcorners,asshown.Aligntopedgesof
fullfrontpanelandconsole;tightencornerscrews.
2 screws
top
edges
1-3/8"screw
10. Tighten the two side screws reinstalled in Step 8.
11. Reinstall and tighten the three remaining side screws.
Custom panel dimensions
IMPORTANT:You need to know what control panel is on
your dishwasher before you order your custom door panel.
For dishwashers with the control panel shown below:
(models KUDSO3FTPA and KUDUO3FTPA)
(Your model may vary slightly from picture above.)
Custom door panel dimensions are:
/
3/4" (19.1 mm)
*This dimension is for 4" (10.2 cm) toe kick. If the installation needs a higher toe
kick, adjust the height of the wood panel accordingly. Not recommended for
toe kicks greater than 6" (15.2 cm).
Follow directions under Option #1 of "Install custom panel"
section.
For dishwashers with the control panel shown below:
(Models KUDC031T, KUDK031T and KUDL031T)
*;_;7 %,?' _d _;_ _ .... '..... _ • ......
(Your model may vary slightly from picture above.)
Custom door panel dimensions are:
23-3/8" (59.4 c "25-29/32" (65.8 cm)
3/4" (19.1 J
mm)
1/8" (3.2 mm)
*This dimension is for 4" (10.2 cm) toe kick. If the installation needs a higher toe
kick, adjust the height of the wood panel accordingly. Not recommended for
toe kicks greater than 6" (15.2 cm).
Follow directions in Option #2 of "Install custom panel"
section.
12
Install custom panel
Option 1: For models KUDS03FTPA and KUDU03FTPA
NOTE: The handle for the custom panel is not included.
IMPORTANT." If the handle is attached from the back of the
custom panel, the screw holes should be countersunk for
the screws heads to be flush with the panel. If the handle is
attached to the front of the custom panel, the screw lengths
cannot exceed the panel thickness. For more information on
KitchenAid custom handle selection, refer to the KitchenAid
Catalog, visit www.kitchenaid.com, or call 1-800-422-1230.
NOTE: A customer-supplied full front panel must weigh no
more than 16 pounds (7.3 kg) and must be made to specific
dimensions. It is recommended that a cabinetmaker cut the
custom panel because of the precise dimensions needed.
NOTE: All mounting hardware supplied is for a 3/4"
(19.1 mm) thick wood panel. If a thinner wood panel, or
materials other than wood are used, it is the consumer's
responsibility to obtain the proper length screws and adjust
the pilot holes accordingly.
iMPORTANT." Use a moisture resistant sealer on both sides
and all edges of the panel to protect it from humidity.
1.
With aTORX _screwdriver, remove three screws from both
sides, as shown; hold the outer panel up while removing
the screws. Save screws for reinstallation.
23-1/2" (59.7 cm) _ "30-3/16" (76.7 cm)
custom panel dimensions
3/4" (19.1 mm)
*This dimension is for 4" (10.2 cm) toe kick. If the installation needs a higher
toe kick, adjust the height of the wood panel accordingly. Not recommended
for toe kicks greater than 6" (15.2 cm).
3 screws _'.
outer panel J
i
i
2. Gently set outer panel aside.
3. Lay the cutomer-supplied custom panel face down on a
protective, non-scratching surface.
4. Measure 9-29/32" (25.2 cm) from top edge and mark a line
on the back of customer-supplied custom panel.
(25.2cm)
mark line
top edge
5. Position the outer panel on the back of the customer-
supplied custom panel as shown, so that the top holes in
the outer panel are on the line, and both panels are
centered side to side.
6. Mark all four hole locations; remove outer panel. Drill
3/32" pilot holes 1/2" (13 mm) deep in customer-supplied
custom panel.
mark pilot holes
7. Place the outer panel on the back of the customer-
supplied custom panel; align holes.
8. Attach outer panel to back of customer-
supplied custom panel with the four _ex head
#10-16 x 3/8" hex head screws supplied in _" screw
the literature package.
9. Attach the handle.The handle should be centered on the
front of the customer-supplied custom panel in the area
shown.
IMPORTANT." Screw heads must be flush with back of
customer-supplied custom panel.
10. Attach the panel assembly to the door by reinstalling the
three screws on each side; do not tighten completely.This
will hold the panel assembly in place on the door frame.
3 screws
customer-supplied
custom panel
13
11.Alignthetopedgeofthecustomer-suppliedcustompanel
withthetopoftheconsole.
12.Drilltwo3/32"pilotholes1/2"(13mm)deep,intothe
customer-suppliedcustompanel,throughtheholesinthe
topcornersontheinnerpanel,asshown.
_anel
align top edges
drill through
these holes
13. Install the two #8-18 x 1-3/8" /q
screws from the literature
package in the top corners
of the inner panel.
14.Tighten the six side screws reinstalled in Step 10.
Option 2: For models KUDC031T, KUDK031T and KUDL031T
All models require an accessory option to attach custom
panels. Kit No. 8171555 (black), 8171556 (white) or 8171557
(biscuit) are available. To order, call customer service at
800-444-1230.
NOTE: A custom full front panel must weigh no more
than 14 pounds (6.3 kg) and must be made to specific
dimensions. It is recommended that a cabinetmaker cut the
custom panel because of the precise dimensions needed.
iMPORTANT: Use a moisture resistant sealer on both sides
and all edges of the panel to protect it from humidity.
NOTE:These dimensions are for frameless custom panel
models with a 4-inch (10.2 cm) console only.
23-3/8" (59.3 "25-29/32" (65.8 cm)
3/4"
(19.1 mm)
custom panel dimensions
1/8"
/8" (3.2 cm)
*This dimension is for 4" (10.2 cm) toe kick. If the installation needs a higher toe
kick, adjust the height of the wood panel accordingly. Not recommended for
toe kicks greater than 6" (15.2 cm).
1. With aTORX _':screwdriver, remove three screws from both
sides of door; hold the outer panel up while removing the
screws.
3 screws
outer panel
2. Gently set outer panel aside.
3. Lay the cutomer-supplied custom panel face down on a
protective, non-scratching surface.
4. Position the outer panel on the back of the customer-
supplied custom panel as shown; make sure top edge of
the outer panel is aligned with the top edge of the
customer-supplied custom panel, and both panels are
centered side to side.
mark4
inner holes
align top
outer panel edges
customer-supplied
custom panel
5. Mark all four hole locations; remove outer panel and drill
3/32" pilot holes 1/2" (13 mm) deep, in customer-supplied
custom panel.
6. Place the outer panel on the back of the customer-
supplied custom panel and align holes.
7. Attach outer panel to back of customer-supplied custom
panel with four #10 x 1/2" wood screws (not supplied).
If the customer-supplied custom panel is less than 3/4"
(1.9 cm) thick where the screws are attached, shorter
screws maybe required.
8. Attach the panel assembly to the door by reinstalling the
three screws on each side.
Ji
---i
3 screws
,,
3 screws
14
Choose attachment option
Excessive Weight Hazard
Use two or more people to move and install
dishwasher.
Failure to do so can result in back or other injury.
Using two or more people, stand the dishwasher up.
Option 1: Countertop
attachment
brackets
The dishwasher must be
secured to the cabi net. There
are two brackets on top of the
dishwasher that can be
attached to the countertop if it
is wood, laminate or other
similar surfaces. If your
countertop is marble, granite or
other hard surface the brackets
may be moved to the sides of
the dishwasher.
front vent
model shown
NOTE: Do not attach the dishwasher, this will be done later.
Option 2: Dishwasher side attachment
(for marble, granite or other hard surface countertop)
1. To remove the brackets from the top, flatten tab at back
of brackets with pliers, and pull the brackets out of the
slots.
tabs
2. Break off the end of the bracket along the scored line.
3.
score line
With another person holding the rear of the dishwasher
to keep it from tipping, open dishwasher door and place
towel over pump assembly and spray arm of
dishwasher. This will keep screws from falling into pump
area when securing dishwasher to cabinet.
4. Push the plastic buttons out of the side of the tub.
NOTE: Save the buttons to cover the holes after
dishwasher is installed.
5.
Push bracket into slot on the side of dishwasher, and
bend tab in towards the side of the dishwasher so that it
keeps the bracket in place. Repeat this step for the other
side of the dishwasher.
NOTE: Do not attach the dishwasher, this will be done
later.
bend
tabs
Check door spring tension
1. With another person holding the rear of the dishwasher
to keep it from tipping, open and close the door a few
times. If the door closes or falls open under its own
weight, the door tension will need to be adjusted.
2. To adjust the door spring tension, unhook the spring
from the rear leg of dishwasher.
3. With a 5/16" nut driver or hex socket, remove the screw
from the tensioner.
4. The screw can be put into one of three holes El, F41,I_ in
the front leg of dishwasher. If the door closes by itself,
move the tensioner to a higher number hole and replace
screw. When door is unlatched, if it opens by itself, move
tensioner to a lower numbered hole and replace screw.
5. Re-attach door spring to rear leg.Tensioners on both
sides of dishwasher should be secured at same holes.
oner
screw
15
Move dishwasher into cabinet opening
Excessive Weight Hazard
Use two or more people to move and install
dishwasher.
Failure to do so can result in back or other injury.
1. Grasp the sides of the dishwasher at the edges of the
door panel.
2. Tilt dishwasher backwards on wheels and move
dishwasher close to cabinet opening. Do not push on the
front of the panel or on the console-they may dent.
3. If dishwasher has a power supply cord, insert power
supply cord into hole cut into cabinet.
If using direct wire, check that it is on the right front side
of opening.
4. Check that water line is on the left side of opening and
drain hose is near the center of the hole in the cabinet.
5. Slowly move dishwasher
completely into cabinet opening.
Do not kink or pinch copper
tubing, drain hose, power supply
cord or direct wire between
dishwasher and cabinet.
Helpful Tip: Once the dishwasher
is in position, you may have to
support the front of the
dishwasher by raising, lowering or shimming front feet.
6. Remove cardboard from under dishwasher.
NOTE: It is all right if dishwasher fits tightly into cabinet
opening. Do not remove insulation blanket -the blanket
reduces the sound level.
Level the dishwasher
1. Align front of dishwasher door panel with cabinet doors.
You may need to adjust alignment to be even with your
cabinets.
HelpfulTip: Prop up one side of frame to hold
dishwasher up off floor when adjusting front legs.
2. Check that leveling legs are firmly against the floor.
3. Close and latch the door, and place level against the
front panel. Check that dishwasher is plumb. If needed,
adjust leveling leg or add shims under rear wheel until
dishwasher is plumb.
4. Repeat for other side of dishwasher.
NOTE: Shims must be securely attached to floor to prevent
their movement when the dishwasher is operated.
5.
Place level against top front
opening of tub. Check that
dishwasher is level from side to
side. If dishwasher is not level,
adjust front legs up or down
until dishwasher is level.
-- _, ,
Make Electrical Connection
Check "Electrical requirements" section.
You need to:
. have the correct electrical supply and recommended
grounding method.
If you are:
. direct wiring, use Option 1
. using a power supply cord, use Option 2
Option 1: Direct wire method
1. Route direct wire so that it does not touch dishwasher
motor or lower part of dishwasher tub.
2.
Pull direct wire through hole in terminal box.
Helpful Tip:
. Select the proper size twist-on
connectors to connect your
household wiring to 16-gauge
dishwasher wiring.
. Insert wire ends into twist-on
connector. Do not pre-twist bare wire.
.Twist connector.
. Gently tug on wires to be sure both are secured.
16
3.
Connect the wires as follows using twist-on connectors
sized to connect direct wire to 16-gauge dishwasher
wire:
Power supply wire: Terminal box wire:
white_-_-white
black_-_ black
ground wire_=_,_gr0und connector
Electrical Shock Hazard
Electrically ground dishwasher.
Connect ground wire to green ground connector in
terminal box.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
4.
Form bare ground wire into a U-shaped hook. Wrap
ground wire hook clockwise around ground connector
and under the washer.
5. Securely tighten ground connector.
-_:,, ...... , __ ground wire washer
_--:_: _'_a _ ground
t__ _ _,_/J "_on necto r
/
ground wire _
6. Tighten clamp connector or conduit connector screws.
7.
Reinstall terminal box cover with wires inside terminal
box.The cover must be outside the box on the left side.
8. Make sure no wires are pinched by cover.
Option 2: Power supply cord method
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
1. Plug into a grounded 3 prong outlet.
2. Check that power supply cord does not touch
dishwasher motor or lower part of dishwasher tub.
Connect to water supply
Helpful Tip:
Compression fittings:
a. Slide nut onto copper tubing about 1" (2.5 cm).
b. Slide ferrule onto the tubing. Do not position ferrule
on the end of the tubing.
c. Put the tubing into the elbow as far as it will go.
d. Slide the nut and ferrule forward and start the nut
onto the elbow threads. Be gentle when handling and
positioning the copper tubing, it bends and kinks
easily.
elbow
nut
1. To prevent vibration during operation, route the water
supply line so that it does not touch the dishwasher
base, frame or motor.
2. With copper tubing pushed into compression fitting as
far as it will go, use a wrench and tighten compression
fitting nut to elbow on water inlet valve.
3. Place paper towel under elbow.Turn on water supply
and check for leaks.
17
Connect to drain
1.
2.
To help minimize vibration, route drain hose to avoid
contact with motor, door springs, water line, cabinet,
flooring or the edge of the hole where it passes through
the cabinet.
Do not remove drain loop from side of dishwasher.
3.
4.
Place pan under end of drain hose. Pan will collect any
water in drain hose.
Place the smaller drain hose clamp onto the small end of
the drain hose.
hose clamp
/
5. Push the drain hose into the connector up to the stop on
the drain hose.
connector stop
6.
Use pliers to open clamp and slide clamp onto
connector between stops on connector as shown.
hose clamp
stops
18
Secure dishwasher in cabinet opening
Tip Over Hazard
Do not use dishwasher until completely installed.
Do not push down on open door.
Doing so can result in serious injury or cuts.
1. If you have not already done so, open dishwasher door
and place towel over pump assembly and spray arm of
dishwasher.This will keep screws from falling into pump
area when securing dishwasher to countertop.
2. Check that dishwasher is still level and centered side to
side in the opening.
3. Secure dishwasher to countertop or sides of cabinet with
two, #10 x 1/2" Phillips-head screws.The dishwasher
must be secured to keep it from tipping when door is
opened. Do not drop screws into bottom of dishwasher.
4.
5.
Open door about 3 inches (7.6 cm) and check that space
between inner door and tub is equal on both sides. If
spacing is not equal, loosen bracket screws and shift tub.
Tighten bracket screws.
If using a countertop attachment to secure dishwasher,
check that top of door does not contact screws, brackets,
or countertop, if it does, dishwasher must be lowered
and re-leveled.
6.
7.
8.
If securing with a side attachment, check that sides of
door do not rub against the screw heads. If they do,
dishwasher must be re-centered. When dishwasher is
properly centered, replace )lastic buttons.
button
Remove towel from dishwasher.
Reinstall the lower dishrack.
Bottom sound pad installation (on some models)
1.
2.
3.
Remove the bottom sound pad from inside the
dishwasher and take it out of the plastic bag.
Place pad on the floor in front of the dishwasher, making
sure lettering is facing up and vinyl pad faces down.
Fold up and hold the side panels down. Carefully slide
the pad toward the back of the dishwasher as far as it
will go, making sure not to push or pull any wires or
hoses. (Do not force.) Side panels will open to proper
position.
NOTE: If there are pipes or other obstructions coming up
through the floor, you will need to cut a slit in the pad to
fit around the obstacle.
4. Fold the front end of the pad up into position. Make sure
the vinyl pad is tucked up behind the door and the
dishwasher front legs, as shown.
Complete installation
1.
2.
Check that grounding clip is attached to the lower panel.
Place the lower panel behind the access panel. Some
models have insulation on the access panel which must
fall behind the insulation on the lower panel.
grounding
clip
3. Hold the two panels together and push them up against
dishwasher leg and vinyl pad.
4. Reinstall the screws through the holes in the access
panel and the slots in the lower panel. Install right side
screw first.
jJ
5. Check that the lower edge of the lower panel contacts
the floor.
6. Tighten the screws.
Direct wire method:
Electrical Shock Hazard
Electrically ground dishwasher.
Connect ground wire to green ground connector in
terminal box.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
Power supply cord method:
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
7, Reconnect power or plug in dishwasher.
19
Check operation
1. Read the Use and Care Guide that came with your
dishwasher.
2. Check that all parts have been installed and no steps
were skipped.
3. Check that you have all the tools you used.
4. Start dishwasher and allow it to complete the shortest
wash cycle. After the first two minutes, unlatch door,
wait five seconds, then open door.
5. Check to see that there is water in the bottom of the
dishwasher tub. Check that dishwasher is working
properly.
6. If not, disconnect power or unplug dishwasher and see
"If dishwasher does not operate" section.
If dishwasher does not operate
First try the solutions suggested here to possibly avoid the
cost of a service call.
o Has the circuit breaker tripped or the house fuse blown?
Is the door closed tightly and latched?
Has the cycle been set correctly to start the dishwasher?
Is the water turned on?
If none of these work, call 1-800-422-1230.
20
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
KitchenAid KUDK03CTWH0 Guide d'installation
- Taper
- Guide d'installation
dans d''autres langues
Documents connexes
Autres documents
-
Whirlpool UDT518SAFP Guide d'installation
-
IKEA IUD9750WS4 Guide d'installation
-
Whirlpool GU3200XTVY1 Guide d'installation
-
Kenmore 66513772K604 Guide d'installation
-
Maytag MDB6701AWS2 Guide d'installation
-
Amana W10212195A Manuel utilisateur
-
Kenmore 66513749K602 Guide d'installation
-
Inglis GU980SCGS2 Guide d'installation
-
GE ZBD9900R00II Guide d'installation