1
MT-5310W/R
Package Contents
MT-5310W/R (x 1)
Pistol grip (x1)
15W power adaptor (x 1)
Stylus (x 1)
RB-3200 Battery pack for pistol grip (x 1)
User manual (x 1)
Barcode scanner user manual (x 1)
MT-5310W/H
Package Contents
MT-5310W/H (x 1)
15W power adaptor (x 1)
Stylus (x 1)
User manual (x 1)
MT-5310W is required to be charged over 8 hours
when used for the first time.
12580900020 Ver. B0
http://www.posiflex.com
MT-5310W
Mobile Terminal System
User Manual
2
SOME IMPORTANT NOTES
FCC NOTES
This system meets industry & government requirements and applicable
standards. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions
manual, may cause interference to radio communications. It has been tested
and found to comply with limits for a Class A digital device pursuant to
subpart B of Part 15 of FCC Rules, which are designed to provide reasonable
protection against interference when operated in a commercial environment.
Operation of this equipment in a residential area is likely to cause interference
in which case the user at his own expense will be required to take whatever
measures to correct the interference.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
CE CLASS A WARNING
This equipment is compliant with Class A of CISPR 32. In a residential
environment this equipment may cause radio interference.
WARRANTY LIMITS
Warranty will terminate automatically when the machine is opened by any
person other than the authorized technicians. The user should consult his/her
dealer for the problem happening. Warranty voids if the user does not follow
the instructions in application of this merchandise. The manufacturer is by no
means responsible for any damage or hazard caused by improper application.
警告使用者
這是甲類的資訊產品，在居住的環境中使用時，可能會造成射頻干擾，
在這種情況下，使用者會被要求採取某些適當的對策。
SAFETY INSTRUCTIONS
This equipment is not suitable for use in locations where children are likely to
be present.
CONSIGNES DE SÉCURITÉ
3
Cet équipement ne convient pas à une utilisation dans des lieux pouvant
accueillir des enfants.
BATTERY CAUTION NOTES
Dispose of used batteries according to the instructions.
Replacement of a battery with an incorrect type that can defeat a
safeguard (for example, in the case of some lithium battery types)
Disposal of a battery into fire or a hot oven, or mechanically crushing
or cutting of a battery that can result in an explosion.
Leaving a battery in an extremely high temperature surrounding
environment that can result in an explosion or the leakage of flammable
liquid or gas.
A battery subjected to extremely low air pressure that may result in an
explosion or the leakage of flammable liquid or gas.
BATTERIE ATTENTION NOTES
Jetez les piles usagées conformément aux instructions.
Remplacement d'une batterie avec un type incorrect qui peut annuler
une sauvegarde (par exemple, dans le cas de certains types de batterie
au lithium)
Mise au rebut d'une batterie dans le feu ou dans un four chaud, ou
écrasement ou coupure mécanique d'une batterie pouvant entraîner une
explosion.
Laisser une batterie dans un environnement environnant à des
températures extrêmement élevées pouvant entraîner une explosion ou
la fuite de liquide ou de gaz inflammable.
Une batterie soumise à une pression atmosphérique extrêmement basse
pouvant provoquer une explosion ou une fuite de liquide ou de gaz
inflammable.
警告
本電池如果更換不正確會有爆炸的危險，請依製造商說明書處理用過之
電池。
4
Product Feature
Ergonomic Design
Pistol grip shape handle is ergonomically designed for easy handling of the
tablet.
Extra Protection
Hand strap strengthens the stability and eases user’s fatigue during the hours of
work.
All-in-one Solution
Optional dock station equips with a built-in 3” thermal printer and various I/O
connectivity; once the tablet is integrated with the dock station, an all-in-one
POS is instantly at your disposal.
Versatile Function
MSR attachment and 1D or 2D barcode scanner built in the pistol grip; MT-
5310W offers more than just mobility but versatility.
Long Hour Operation
MT-5310W is designed with advanced power saving technology that provides
long battery life for daily operation. The pistol grip also houses a removable
battery that can vastly extend the overall operating time.
Views of MT-5310W/H
Front View
LED Indicator
Projected Capacitive
Touch Screen
Rubber Cushion
Rubber Cushion
5
Rear View
Bottom Side View
Left Side View
microUSB Port
Power Button
Nano SIM Card Slot
(Only available for MT-5310W with 4G Module)
Micro SD Card Slot
Mic-in/Line-Out
Combo Jack
Rear Camera
Speaker
Hand strap
Expansion Slot for
Optional Attachment
Docking Station Connector
5VDC-IN Power Jack
Docking Station Locking Hole
Smart Card Reader
(Optional)
6
Load RB-3200 Battery Pack and a stylus into
Pistol Grip PG-500 (for MT-5310W/R)
MT-5310W/R with PG-500 pistol grip support 1D CCD, 1D Laser, and 2D
barcode scanner. Before the scanner can be initiated, it is required to install the
battery pack RB-3200 and a stylus in the battery compartment inside the pistol
grip. Please follow the steps listed below to finish the installation.
1. Press down the lever and then push up the cover for battery
compartment as shown in the figure.
2. To replace the existing battery, gently push
the metal clip outwards to release the
battery. If you are installing the battery for
the first time, please skip to the next step.
3. After having the rail on the battery pack
aligned with battery clip, push down the
battery pack into battery compartment.
4. Push down the cover to close the battery
compartment.
Metal clip
7
Connecting the Pistol Grip onto MT-5310W/R
MT-5310W/R model is equipped with an additional pistol grip which aims to
help users grip the terminal more easily while they are operating the scanner.
Please refer to the following instructions to install the pistol grip onto the tablet.
Warning
Please note that MT-5310W/R can only operate with PG-500 pistol
grip. Operating with PG-200/201 or other pistol grip model will cause
some unknown problems or damages, which is considered as an
artificial damage and is not covered by the warranty.
1. To attach the pistol grip to the tablet, align the arrow head on the top
side of the pistol grip with the tail of the arrow on the rear of the
tablet.
2. After ensuring the pistol grip is well
attached to the tablet, push the pistol
grip in the direction indicated by the
arrow as shown in the figure.
3. Make sure the head of the down arrow on the pistol grip is supposed to
be aligned with the head of the arrow on the rear side of the tablet as
the below figure shows, which indicates the pistol grip is well
mounted.
4. To check how much battery capacity
remains in PG-500 pistol grip, press the
battery capacity checking button on the
pistol grip to show the current battery
capacity level through the LED
indicator.
8
Replacing the Pistol Grip with a Hand Strap Cover (Optional)
The hand strap cover is an optional peripheral designed for users to easily hold
the tablet for operation. To replace the pistol grip with a hand strap cover,
follow the steps listed below.
1. While pushing the release lever to the left
(1), slide the pistol grip in the direction
indicated by the arrow in the figure (2).
2. Pull the pistol grip off from the tablet.
3. Align the hand strap cover with the grooves
on the rear side of the table.
4. Make sure that the hand strap cover is well
attached to the rear side of the tablet.
5. Slide the hand strap cover up in the
direction indicated by the arrow until it is
clicked into place.
1
1
2
2
9
6. Fasten the hand strap cover onto the tablet
using a screw.
Replacing the Hand Strap Cover with a Pistol Grip (Optional)
Please follow the below steps to replace the hand strap cover with a pistol grip.
1. Loosen the screw to remove the hand strap
cover from the tablet.
2. Slide the hand strap cover down in the
direction indicated by the arrow.
3. Remove the hand strap cover from the
rear side of the tablet.
4. Go through the Connecting the Pistol Grip onto MT-5310W/R
section which is described previously to complete the installation of
the pistol grip onto the tablet.
Installing micro SD Card or SIM card in MT-5310W
Please follow the below steps complete the installation of micro SD card and
SIM card.
1. Turn off MT-5310W completely. Then, pull off the rubber cover
located on the right side of your tablets to find micro SD card slot
and nano SIM card slot.
10
2. Have the rear of the tablet face towards you to install micro SD
card or SIM card.
2.1. To insert a micro SD card into the
micro SD card slot, make sure the
side with the golden finger of the
card faces downwards, and then slide
the card down into the slot.
2.2. Similarly, to install a SIM card, push
SIM card into nano SIM card slot
with its gold contacts facing towards
you.
3. Pull off the rubber cover to close the compartment.
4. If you attempt to release a micro SD card or SIM card from the
slot, push the card with your fingertip to slide it out.
Charging the Battery
Below are some cautionary advices you need to keep in mind while you
attempt to charge the battery.
1. MT-5310W is required to be charged over 8 hours when used for the
first time.
2. When the low battery warning message appears as shown below,
please fully charge the battery to avoid data loss.
3. When the low battery capacity indicator on the pistol grip beams or
low battery warning message appears, please charge or replace the
battery for the pistol grip immediately.
4. Only charge the battery with power adapter which comes with
MT-5310W. Using a different power adapter may damage your device.
5. When the battery is running very low (less than 6 percent of battery
capacity), the system will be automatically shut down to protect the
battery from being over-discharged.
11
Please go through the following instructions to charge MT-5310W using the
power adapter.
For MT-5310W/R
In considering the battery life could be consumed drastically under heavy
usage, you may also choose to purchase either another replacement battery
RB-3200 for the pistol grip or the battery charger CS-100 for rapidly charging
the replacement battery RB-3200.
1. Connect the power connector of the
power adaptor to the tablet.
2. Plug the AC power adaptor cord into an electrical outlet. In general,
the tablet battery will be charged first. Once the process of charging
the tablet is complete, the pistol grip battery will then be charged.
For MT-5310W/H
1. Find the power jack on the left side of your tablet, and then connect
the power connector of the power adaptor to it.
2. Plug the AC power adaptor cord into an electrical outlet to initiate the
charging process.
Status LED Indicator
LED indicator is specially designed to deliver special message regarding the
current system status and battery life. The blow chart enumerates all the
possible LED indicators and its meaning for your reference.
LED Status
System Status
Descriptions
Solid blue
ON
￭ System booting.
Solid Red
ON
￭ System is being charged.
Blinking Red
ON
￭ Battery charging error occurs
OFF
ON
￭ System enters sleep mode.
￭ System has been booted to Windows.
￭ Battery is fully charged.
OFF
OFF
￭ System powers off
12
Powering ON/OFF MT-5310W
Power ON MT-5310W
To power on MT-5310W, keep pressing the power button of the machine
for 5-10 seconds. If the terminal falls into the sleep mode after remaining
idle for a specific period of time, push the power button to wake the device
up.
Power OFF MT-5310W
When MT-5310W stays in idle mode, push the power button to put your
device into sleep mode, and press the power button again to wake up the
tablet. To completely shut down the machine, you need to press and hold
the power button for at least 20 seconds. In the case the system halts for
unknown reasons, you are advised to hold down the button until a system
shutdown is initiated.
Operating TA-220/300 Magnetic Stripe Reader (Optional)
MT-5310W model also offer MSR solutions. As optional items, TA-220/300
both allow you to integrate built-in MSR into MT-series tablet. However, TA-
220 mainly supports MSR with RFID but TA-300 is an attachment combined
with three-track MSR and finger printer sensor.
Please go through the following instructions on how to operate magnetic stripe
reader provided via TA-220/300.
1. Have the side with the magnetic stripe of a card
face the touch panel of the tablet.
2. Swipe the magnetic stripe card along the track
of the reader from top to bottom or from
bottom to top.
Operating the 1D/2D Scanner (for MT-5310W/R)
MT-5310W/R model is equipped with an
optional 1D CCD, 1D Laser, or 2D scanners
features 1D and/or 2D barcode scanning. It
also supports two types of USB interfaces,
USB HID or USB Virtual COM, and the
scanner is generally set to USB HID mode
by default. For more detailed information,
please refer to the barcode scanner user
manual.
13
Mounting TA-600 onto MT-series Tablet (Optional)
TA-600 is an external battery pack kit mainly
designed to provide extra battery life to MT-
series tablet. For the detailed installation
instructions, please refer to TA-600 user
manual.
Installing an Operating System
You are highly advised NOT to install or change the Windows operating
system and drivers which are preloaded on MT-5310W without professional
instructions. Not only might the careless handling during installation cause
irreversible damage to your system, but also the improper installation likely
leads to system malfunction or failure. Please contact with your dealers about
the issues of operation system installation.
Performing System Recovery
For MT-5310W models with preloaded operating systems, you are NOT
encouraged to recover your system without the help of the system integrators.
Please be advised to contact your service center for further assistance with
system recovery.
Installing Optional Upgrade Kits
Posiflex MT-5310W can work with multiple optional upgrade kits, such as
MSR, Smart Card Reader and the like. For the detailed instructions, refer to
the user manual related to each peripheral devices.
14
Specifications
MT-5310W
System
CPU
Kaby Lake-Y CPU
DRAM Memory
4GB / 8GB (4GB as default)
Rear Camera
5MP AF rear facing camera
Sensors
G sensor, ambient light sensor
Battery
7.6V/ 3570 mAh, 27.14Wh
Storage
Storage
16GB/32GB/64GB eMMC (on-board)
Or SSD (on-board)
OS Support
OS Support
Windows 10 IoT (64-bit)
Display & Monitor
Display
10” TFT LCD with LED backlight, 1920 x 1200
Touch Screen
P-CAP touch with multi-touch support
Expansion
Wireless connectivity
1. WiFi IEEE 802.11a/b/g/n/ac + BT 4.0
2. Optional 4G LTE module (M.2 form factor, USB I/F)
Power
Power Supply
5V/15W (2-pin plug) power adaptor
Outside I/O Ports
Audio
Built-in speaker + Mic-in/Line-out combo port
USB Port
Micro USB x1 (non OTG USB Port)
SIM Card
Nano SIM card slot x 1
(only available for MT-5310W with 4G module)
Micro-SD Card
Micro-SD card slot x 1
Power Switch Button
Yes
LED Indicator
Blue color LED x 1
Red color LED x 1
Mechanical
Dimension
260.7 (L) x 175.0 (W) x 16.8 mm (D)
Weight
950g
15
MT-5310W
Optional Item
Smart Card Reader
Yes, IDTECH MiniSmart II
4G comm.
4G LTE module
Sunlight readable
Sunlight readable panel display
Attachment
TA-100
Side attachment with external USB 2.0 port
TA-220
Side attachment with three-track MSR and RFID
TA-300
Side attachment with three-track MSR and finger print
sensor
TA-600
Battery pack Kit
PG-500
Pistol grip supports 1D/2D barcode scanning.
DS-110
Dock station: USB 2.0 x 3 + GbE x 1 + Serial Port x 2 +
CR Port x 1 + DC-in + 2” WiFi Printer x 1
DS-200 / 210 / 220 /
300 / 310 / 320
Dock Station: USB 2.0 x 3 + GbE x 1 + Serial Port x 2 +
CR Port x 1 + 3” WiFi Printer x 1
Note: (*) Either smart card reader or 4G module can be installed into MT-
5310W system.
※
The product information and specifications are subject to change without
prior notice. To get the detailed information on the MT-5310W, please check
this model from Posiflex Global Website
16
<MEMO>
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
