Winmate M900P Guide de démarrage rapide

Marque
Winmate
Modèle
M900P
Catégorie
Comprimés
Taper
Guide de démarrage rapide
Please read these instructions carefully before using this product, and save this manual for future use.
M900P
8-inch Rugged Windows Tablet
Intel® Apollo Lake Pentium N4200
Windows 10 IoT Enterprise
Quick Start Guide
Version 1.0
Document Part Number: 91521110104A
2
8-inch Rugged Windows Tablet M900P Quick Start Guide M101P
Table of Contents
Preface 3
Chapter 1: Introduction 7
1.1 Overview 7
1.2 Unpacking 7
1.3 Description of Parts 7
1.4 Indicators 9
1.5 Hotkey for Specific Functions 9
Chapter 2: Getting Started 10
2.1 First-Time Operation 10
2.2 Installing SIM Card (For 4G/LTE Equipped Devices) 10
2.3 Installing Battery 11
2.4 Charging Your Tablet 11
2.5 Starting the Tablet 12
2.6 Replacing the Battery 12
Chapter 3: Operating the Device 13
3.1 Using Hottab Utility 13
3.2 Using the Camera 14
3.3 Changing Touch Mode 14
3.5 Scanning Barcodes 15
3.6 Reading RFID Tags 15
3.7 Reading MSR/ EMV Cards 16
3.8 Basic Troubleshooting 17
Chapter 4: In-Vehicle Applications 19
4.1 Installing Vehicle Cradle 19
4.2 Installing Vehicle Gateway VG-100 20
Appendix 21
Appendix A: Specifications 21
Appendix B: Order Information 22
Appendix C: Accessories 22
Appendix D: Docking Connector Pin Definition 23
Appendix E: D-sub Pin Definition 23
3
Preface
Preface
Advisory Conventions
Four types of advisories are used throughout the user manual to provide helpful information or to alert you
to the potential for hardware damage or personal injury.
Note:
A note is used to emphasize helpful information
Important:
An important note indicates information that is important for you to know.
Caution/ Attention
A Caution alert indicates potential damage to hardware and explains how to avoid the
potential problem.
[FR] Une alerted’at tentionindique un dommage possible à l’équipement et explique
comment éviter le problèm e potentiel.
Warning!/Avertissement!
An Electrical Shock Warning indicates the potential harm from electrical hazards and
how to avoid the potential problem.
[FR] Un Avertissement de Choc Électrique indique le potentiel de chocs sur des
emplacements électriques et comment éviter ces problèmes.
FCC Statement
This equipment has been tested and found to comply with the limits for a class "B" digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at him own expense.
CE Notice (European Union)
Electromagnetic Compatibility Directive (2014/30/EU)
EN55024: 2010/ A1: 2015
o IEC61000-4-2: 2009
o IEC61000-4-3: 2006+A1: 2007+A2: 2010
o IEC61000-4-4: 2012
o IEC61000-4-5: 2014
o IEC61000-4-6: 2014
o IEC61000-4-8: 2010
o IEC61000-4-11: 2004
EN55032: 2012/AC:2013
EN61000-3-2:2014
EN61000-3-3:2013
Low Voltage Directive (2014/35/EU)
EN 60950-1:2006/A11:2009/A1:2010/A12:2011/ A2:2013
This equipment is in conformity with the requirement of the following EU legislations and harmonized
4
8-inch Rugged Windows Tablet M900P Quick Start Guide M101P
standards. Product also complies with the Council directions.
Safety Information
Precaution on Battery Pack
Précaution avec le bloc-pile
Do Not Disassemble, Modify, or Insert Sharp
Objects Into the Battery Pack. Electrolyte leakage,
generation of heat, ignition or rupture may result.
[FR] Ne pas démonter, modifier, ou insérer des
objets pointus à l'intérieur du bloc-pile. Une fuite
d'électrolyte, la génération de chaleur, l'amorçage
ou la rupture peuvent être occasionnés.
Do Not Short the Positive (+) and Negative (-)
Terminals of the Battery. Generation of heat,
ignition or rupture may result. When carrying or
storing the device, do not place the battery pack
together with articles that may contact electricity.
[FR] Ne pas court-circuiter les bornes Positive (+)
et Négative (-) de la pile, la génération de chaleur,
l'amorçage ou la rupture peuvent être occasionnés.
Lors du transport et du rangement de l'appareil, ne
pas placer le bloc-pile en même temps que des
articles pouvant créer un contact électrique.
Do Not Apply Shocks to the Battery by Dropping It
or Applying Strong Pressure to It. Electrolyte
leakage, generation of heat, ignition or rupture of
battery may occurs.
[FR] Ne pas faire subir de choc à la pile en la
laissant tomber ou en appliquant une forte pression
dessus. Une fuite d'électrolyte, la génération de
chaleur, l'amorçage ou la rupture peuvent être
occasionnés.
Do Not Charge the Battery Other Than Methods
Those Specified In This Manual. If the battery is not
charged using one of the specified methods,
electrolyte leakage, generation of heat, ignition or
rupture may result.
[FR] Ne pas charger la pile par d'autres méthodes
que celles spécifiées dans ce manuel. Si la pile
n'est pas chargée en utilisant l'une des méthodes
spécifiées, une fuite d'électrolyte, la génération de
chaleur, l'amorçage ou la rupture peuvent être
occasionnés.
When the Battery Pack Has Deteriorated, Replace
It with a New Battery. Continued use of a damaged
battery pack may result in heat generation, ignition
or battery rupture.
[FR] Lorsque la pile est détériorée, la remplacer par
une nouvelle pile. L'utilisation continue d'une pile
endommagée peut occasionner une génération de
chaleur, l'amorçage ou la rupture de la pile.
Do Not Expose the Battery Pack to Excessive Heat,
or Extreme Heat (Near Fire, in Direct Sunlight for
example) Generation of heat, ignition or rupture
may result
[FR] Ne pas exposer le bloc-pile à une Chaleur
Excessive, ou une Chaleur Extrême (Près d'un feu,
sous la lumière du soleil par exemple)Une
production de chaleur, l'amorçage ou la rupture
peuvent être occasionnés
Do Not Use the Battery Pack With Any Other
Products. The battery pack is rechargeable and is
only designed for this specific product. If it is used
with a product other than the specified product,
electrolyte leakage, generation of heat, ignition or
rupture may result.
[FR] Ne pas utiliser avec un autre produit La
batterie est rechargeable et a été conçue pour un
produit spécifique. Si elle est utilisée sur un produit
différent
de celui pour lequel elle a été conçue, des pertes
d’électrolytes et une production de chaleur sont
possibles, elle risque également de prendre feu ou
de casser.
Do Not Use This Product With Battery Other Than
the One Specified.
[FR] Ne pas utiliser ce produit avec une batterie
autre que celle spécifiée
Discontinue using device immediately if you notice
the battery is swelling, or looks puffy or misshapen.
Do not attempt to charge or use the device. Do not
handle a damaged or leaking battery. Do not let
leaking battery fluid come into contact with your
eyes, skin or clothing.
[FR] Si vous remarquez une pile gonflée, élargie ou
anormale, cesser l’utilisation de l’appareil
immédiatement. N’essayez pas de recharger
l’appareil ou de l’utiliser. Ne pas manipuler une pile
qui fuit ou qui est endommagée. Ne laissez pas de
liquide qui fuit entrer en contact avec vos yeux,
votre peau ou vos vêtements.
5
Preface
General Product Safety
Sécurité générale des
produits
Do not block any ventilation openings. Do not
place the product against a wall or in an enclosed
space as doing so might impede the flow of
cooling air.
[FR] Ne pas bloquer les ouvertures de ventilation.
Ne pas placer le produit contre un mur ou dans un
espace clos de façon à entraver la circulation de
l'air de refroidissement.
Do not place the product near any heat sources
such as radiators, warm air intakes, stoves or
other heat-generating devices (including amplifiers
or other heat producing equipment).
[FR] Ne pas placer le produit près d'une source de
chaleur comme des radiateurs, les arrivées d'air
chaud, poêles ou autres produits générant de la
chaleur (y compris les amplificateurs ou autre
équipement produisant de la chaleur.)
Protect the power cord from being crushed or
pinched, particularly in the area of the plugs, any
receptacles used, and the point of exit from the
apparatus. Do not break off the ground pin of the
power cord.
[FR] Empêcher le cordon d'alimentation d'être
écrasé ou pincé, en particulier dans les zones de
prises, des containers utilisés, et du point de
sortie de l'appareil. Ne pas casser la broche de
terre du cordon d'alimentation.
Do not disregard the safety that a polarized or
grounded connection can provide. A polarized
connection consists of two plugs, one of which is
larger than the other. A grounded connection has
two blades and a third one that is grounded. If the
main plug provided cannot be inserted into your
outlet, consult an electrician to replace your
obsolete outlet.
[FR] Ne pas ignorer la sécurité qu'une prise
polarisée ou une prise de terre peut prévoir. Une
prise polarisée se compose de deux fiches, dont
l'une est plus large que l'autre. Une prise de terre
possède deux lames et une troisième qui est la
terre. Si la fiche principale fournie ne peut être
insérée dans votre prise, consultez un électricien
pour remplacer votre prise obsolète.
Use only accessories specified by the
manufacturer.
[FR] Utiliser uniquement les accessoires spécifiés
par le fabricant.
This product should not be used near water such as
bathtubs, sinks, swimming pools, wet basement,
etc.
[FR] Ce produit ne dois pas être utilisé près de l'eau
comme les baignoires, les éviers, les piscines, les
sous-sols humides, etc.
Use only with its transport carriage, stand, tripod,
console or table specified by the manufacturer or
sold with the product. When using a carriage,
move the carriage assembly with the product
carefully to avoid damage from falling over.
[FR] Utiliser uniquement avec son chariot de
transport, support, trépied, console ou table
spécifiés par le fabricant ou vendu avec le produit.
Lors de l'utilisation d'un charriot, déplacez
l'ensemble chariot avec le produit avec soin pour
éviter tout dommage de chute.
Unplug this apparatus during lightning storms or
when it is not being used for long periods.
[FR] Débrancher cet appareil durant les orages ou
lorsqu'il n'est pas utilisé pendant de longues
périodes.
Refer all servicing to qualified service personnel.
A technical intervention is required when the
apparatus has been damaged in any way, for
example if the power cord or plug is damaged,
liquid has been spilled or objects have fallen
inside the unit, if the product has been exposed to
rain or moisture, if it does not operate normally or
if it has been dropped.
[FR] Confier toute réparation à du personnel
qualifié. Une intervention technique est nécessaire
lorsque l'appareil a été endommagé de quelque
façon, par exemple si le cordon d'alimentation ou
la fiche est endommagé, du liquide a été renversé
ou des objets sont tombés à l'intérieur de l'unité, si
le produit a été exposé à la pluie ou à l'humidité,
s'il ne fonctionne pas normalement ou s'il a été
jeté.
6
8-inch Rugged Windows Tablet M900P Quick Start Guide M101P
Handling and Maintenance
General Guideline
Guide Général
Keep the product at least 13 cm (5
inches)away from electrical appliances that
can generate a strong magnetic field such as
TV, refrigerator, motor, or a large audio
speaker.
[FR] Garder le produit au moins à 13 cm (5
pouces) de distance des appareils électriques
qui peuvent générer un fort champ magnétique
comme une télévision, un réfrigérateur, un
moteur, ou un important haut-parleur.
Do not place heavy objects on top of the tablet
computer as this may damage the display.
[FR] Ne pas placer d'objets lourds sur le
dessus de l'ordinateur tablette cela peut
endommager l'écran.
The screen surface can be easily scratched.
Use with care. Do not use paper towels to
clean the display but use the included cleaning
cloth. Avoid touching it with a pen or pencil.
[FR] La surface de l'écran peut être facilement
rayée. Utiliser avec précaution. Ne pas utiliser
de serviette en papier pour nettoyer l'écran
mais utiliser le chiffon de nettoyage inclus.
Éviter de toucher avec un stylo ou un crayon.
To maximize the life of the backlight in the
display, allow backlight to automatically turn off
as a result of power management. Avoid using
a screen saver or other software that prevents
the power management from working.
[FR] Pour maximiser la durée de vie du
rétroéclairage de l'écran, autoriser le
rétroéclairage résultant de la gestion de
l'alimentation. Éviter d'utiliser un économiseur
d'écran ou un autre logiciel empêchant la
gestion de l'alimentation de fonctionner.
Cleaning Guideline
Guide de nettoyage
Use a soft cloth moistened with water or a non-
alkaline detergent to wipe the exterior of the
product.
[FR] Utiliser un chiffon doux humidifié avec de
l’eau ou un détergeant non alcalin pour
essuyer l'extérieur du produit.
Gently wipe the display with a soft, lint-free
cloth. Do not use alcohol or detergent on the
product.
[FR] Essuyer délicatement l'écran avec un
chiffon doux non pelucheux. Ne pas utiliser
d'alcool ou un détergent sur le produit.
Touchscreen Guideline
Guide de l'écran tactile
Use your finger or the stylus on the display.
Using sharp or metallic object may cause
scratches and damage the display, thereby
causing errors.
[FR]Utiliser votre doigt ou le stylet sur l'écran.
L'utilisation d'un objet pointu ou métallique
peut provoquer des rayures.
Use a soft cloth to remove dirt on the display.
The touchscreen surface has a special
protective coating that prevents dirt from
sticking to it. Not using a soft cloth may cause
damage to the special protective coating on
the touchscreen surface. To clean off hard to
remove dirt, blow some steam on the particular
area and gently wipe away using a soft cloth.
[FR]Utiliser un chiffon doux pour enlever la
poussière sur l'écran. La surface de l'écran
tactile a un revêtement protecteur spécial
empêchant la saleté de se coller à lui. Ne pas
utiliser un chiffon doux peut endommager le
revêtement spécial sur la surface de l'écran
tactile. Pour nettoyer les saletés plus difficiles
à enlever, souffler de la buée sur la zone
particulière et essuyer doucement avec un
chiffon doux.
Do not use excessive force on the display.
Avoid placing objects on top of the display as
this may cause the glass to break.
[FR]Ne pas utiliser une force excessive sur
l'écran. Éviter de placer des objets au dessus
de l’écran cela pourrait provoquer une cassure
du verre.
When there is a noticeable discrepancy in the
operation of the touchscreen function (your
touch does not correlate to the proper location
on the screen), recalibrate the touchscreen
display.
[FR]Lorsqu'il y a un écart sensible dans le
fonctionnement de l'écran tactile (votre contact
ne correspond pas à la bonne position sur
l'écran), recalibrer l'écran tactile.
7
Chapter 1: Introduction
Chapter 1: Introduction
1.1 Overview
Thank you for purchasing 8-inch Rugged Windows Tablet Computer M900P.
The M900P is a compact rugged tablet PC with robust set of features designed to withstand industrial use
while providing high tech solutions that increase productivity, improve safety, and reduce operational costs.
The processing power comes from Intel's Apollo Lake processor paired with genuine Intel graphics for high
performance. The tablet features a brilliant projective capacitive touch screen, which is outdoor viewable
and offers 1280 x 800 pixel resolution. Weighing at just 2.2 pounds (approx. 900 grams) the M900P
delivers lightweight mobility in a rugged tablet.
Highlights
Intel® Apollo Lake Pentium N4200 processor
8'' daylight readable panel with direct optical bonding
Default D-sub for vehicle gateway connection
Optional EMV/MSR reader
IP65 waterproof and dustproof
1.2 Unpacking
Check and identify the standard supplied accessories.
Standard factory shipment list:
8-inch Rugged Tablet M900P
Standard Battery
Power Adapter
Power Cord and Plugs
Quick Start Guide
Driver CD
Your package may include other optional accessories based on your order.
Desk Dock
Vehicle Cradle
Battery Charger
Vehicle Gateway
Carry Bag
Hand Strap with Capacitive Touch Stylus
8
8-inch Rugged Windows Tablet M900P Quick Start Guide M101P
1.3 Description of Parts
No
Item
Description
1
Camera
2 MP Webcam.
2
8” Touch
Screen
Display and act as one of the
inputs for the rugged tablet.
3
Speaker
Two 1 Watt speakers for
audio output.
4
LED
Indicators
Show the current status of
the Tablet: power, battery,
wireless communications,
and storage.
5
Light
Sensor
Light sensor helps to adjust
display backlight.
6
Mic
Use during video recordings
and communications.
7
Power Button
Power on/off tablet.
8
Menu Button
Hottab quick access.
9
Function
Buttons
Three programmable function
key configured by Hottab
Utility.
10
Mic
Use during video recordings
and communications.
11
Optional
Docking
Connector
Port to docking solutions
such as desk docking to
provide power and external
I/O.
12
Kensington
Security Slot
Insert the lock into the
Kensington slot on the tablet
and secure the lock with its
key or its combination.
13
Optional
Barcode
Allows you to scan 1D/2D
barcodes.
No
Item
Description
14
D-Sub
Connector
To connect a Vehicle
Gateway.
15
Mic In/Line Out
Connect headset or
headphone (Mic is only
supported with 3.5mm 4-
pin headset).
16
USB 3.0
Type-A
USB 3.0 port connects to
USB devices, such as USB
flash drive, mouse,
keyboard, printer, etc.
5V/0.9A.
17
Reset Button
Hardware reset button.
18
USB 3.0
Type-C
High speed USB port
connects to USB devices,
such as mouse, keyboard,
printer, etc.
*No ALT support,
power output 5V/0.9A
19
Power Jack
Power input 19V DC,
3.24A.
20
I/O Cover
Protect I/O ports
21
Rear Camera
8MP camera with
autofocus and LED light.
22
Battery Lock
Latch
Latch to lock the battery in
place once battery is
inserted.
23
Battery
7.6V, typ. 4200 mAh Li
Polymer Battery (2S2P).
24
4G/ LTE
Module, SIM
card slot
Service window to insert
Micro SIM card. Also
provide access to 4G / LTE
Module.
25
Optional RFID
Allows you to read HF
RFID tags.
26
Front LED Indicator Details:
9
Quick Start Guide
1.4 Indicators
Indicator
Icon
Description
Power Indicator
Blue– Tablet is on.
No light– Tablet is off.
Battery Status
Orange–AC adapter is plugged in and charging.
Green–AC adapter is plugged in and battery is full charged.
Solid Red - Low battery (<10%).
Blinking Red – Battery is being hot swapped.
No light – Battery is in use and more than 10%.
Disk Activity Indicator
Green - Disk is active.
No light - Disk is idle.
RF Communications
Green – Wi-Fi/BT/WWAN/GPS is on.
No light – Wi-Fi/BT/WWAN/GPS are all Off.
1.5 Hotkey for Specific Functions
For the physical buttons on the tablet computer, in addition to its dedicated functions detailed in the
previous section, it can also be used to emulate commonly used keyboard key strokes. Under different
scenario, a single physical button or a combination of physical buttons provide different keyboard key
strokes, which are specified below:
In POST (Before Windows boots up):
Button
Keystroke
Fn1
F6 to enter
Recovery Menu
Fn2
F7 to enter BIOS
setup screen
Fn3
Keyboard F3
Menu + Fn1
Enter
In Windows:
Button
Keystroke
Menu
Hottab Quick Access
Fn1
Default: Web Browser
Fn2
Default: Camera,
Fn3
Default: Notepad, or
Barcode trigger (Note 1).
Power
Power ON/ OFF
Note: Fn3 is trigger button when connected with barcode scanner.
10
8-inch Rugged Windows Tablet M900P Quick Start Guide M101P
Chapter 2: Getting Started
2.1 First-Time Operation
To get started:
1. Install SIM card.
2. Install storage card.
3. Install the battery.
4. Charge your tablet.
5. Start the tablet.
2.2 Installing SIM Card (For 4G/LTE Equipped Devices)
The Tablet Computer supports 4G/LTE data connection and fits a Micro-SIM card.
Caution
Power off the tablet before installing the 4G/LTE module and Micro SIM card, or the tablet
computer might be damaged by the incorrect installation behaviors.
To install the SIM card:
1. Unscrew four screws that secure the service window in the rear.
2. Remove the screw that secures the 4G/LTE module.
3. Carefully lift the module up. Do not to damage the connected cable!
4. Install SIM card into slot with IC facing down the contact patch. Reposition the removed 4G/LTE
module screw and service window screws to secure the service window.
❶
❷
❸
❹
11
Quick Start Guide
2.3 Installing Battery
To install the battery pack:
1. Disconnect any cords connected to the tablet computer.
2. Turn the tablet over, back facing up.
3. Locate the Battery Lock Latch and push it to the “Unlocked” position.
4. Locate the Battery Release Slider that is spring-loaded. Pull back and hold.
5. Insert the battery with the connector-pins side first, and then lower the battery into the battery
compartment. Continue to hold the Battery Release Slider until the battery is fully inserted.
6. Make sure the battery is completely lowered into the compartment before letting go of the Battery
Release Slider. Battery will be flat against the housing once fully inserted.
To remove the battery pack:
1. Shut down the tablet (or put into sleep mode). Disconnect any cords connected to the computer.
2. Turn the tablet computer over, back facing up.
3. Locate the Battery Lock Latch and push it to the “Unlocked” position.
4. Locate the Battery Release Slider that is spring-loaded. Pull back and hold.
5. Lift the battery out using the opening on the side of battery compartment.
2.4 Charging Your Tablet
The tablet operates either on external AC power or internal battery power. It is recommended to use AC
power when you start up the Tablet for the first time.
Caution: Use only the AC adapter included with your Tablet Computer. Using other AC
adapters may damage the Tablet Computer and the Battery.
To connect a tablet to AC power:
1. Open I/O protective cover by pulling out the latch.
2. Plug the DC cord of the AC adapter into the power jack of the tablet computer.
3. Plug the AC power cord into the AC adapter.
4. Plug the AC power cord into the electrical outlet.
The battery LED indicator shows different battery states:
Orange - AC adapter is plugged in and battery is charging.
Green - AC adapter is plugged in and battery is fully charged.
Solid Red - Low battery level (<10%).
Blinking Red – Battery is being hot swapped.
No light – Battery is in use and charged (>10%).
Item
Battery Operation Time
Battery Charging Time
Standard Battery
6-8 Hours
2.5 Hours
12
8-inch Rugged Windows Tablet M900P Quick Start Guide M101P
2.5 Starting the Tablet
Important: When powering on the device for the first time, please make sure there’s no
interruption during the Windows setting up process, for example, accidentally powering off. If
it happened, please access the recovery menu by pressing Fn1 button on the front bezel to
initiate recovery process.
Press and hold the power button for 3 seconds until the blue LED power indicator light up.
Note: Do not press the power button repeatedly.
Do not perform the following operations until the Disk Activity Indicator off
Connecting or disconnecting the AC adapter
Pressing the power button
Touching the tablet buttons, screen, or external keyboard/mouse
To power off the Tablet Computer:
1. Close any programs that are open on the Desktop. Start Screen apps don’t need to be closed.
2. Tap on the Settings charm.
3. Tap on Power.
4. Tap on Shut Down.
5. Wait for Tablet Computer to power off.
Note: The computer will forcibly be powered off if the power button is pressed and held
for 6 seconds or longer.
2.6 Replacing the Battery
The M900P Tablet supports hot-swap, meaning the tablet doesn’t need to be powered off to replace the
main battery. To support hotswap, there is a backup battery inside the tablet that is charged together
with the main battery. This battery cannot be removed, and requires adequate power for main battery hot
swapping. When the backup battery is fully charged, the tablet can sustain up to 5 minutes of runtime for
battery hot-swapping.
Perform the following to hot swap the batteries:
1. Power on the tablet, open Hottab to check the power level of the Backup battery.
2. If the Backup battery level is “Low”, please charge the tablet with AC Power until the Backup
battery level is “Medium” or “High”, and do not remove the main battery.
3. If the Backup battery level is at “Medium” or “High”, you can remove the main battery.
4. Insert a new fully charged battery into the battery compartment.
5. Pen Hottab to check Main battery level. If the battery level is displayed incorrect, check if the new
removable battery is inserted properly.
6. If the battery level displayed correct, continue using the tablet.
Caution: Charge the built-in back-up battery every two months to keep battery health
and prevent possible issues from battery over-discharge.
13
Quick Start Guide
Chapter 3: Operating the Device
3.1 Using Hottab Utility
Hottab provides quick access to the tablet’s functions and features, such as setting up shortcuts, using
camera, powering on/off built-in devices, programming function key, and changing power management.
Note:
Please download the SDK from Winmate Download Center.
>> M900P >> Development Kit or check the Driver CD which is shipped with the tablet.
Please notice that HF RFID reader, Barcode reader, MSR & Contact EMV reader are
optional module, please make sure user have ordered the module before using the SDK.
As Windows starts up, Hottab starts and runs in the background. To display the Hottab control utility, press
the (Menu) Button located on the front panel, OR launching the Hottab Utility application.
(Menu) Button on the Front Panel:
Hottab Utility Icon:
The main user interface is located on the right side of the screen. There are 4 main menu options:
Shortcuts, Camera, Device ON/OFF, and Settings. Operations and functions on each menu options is
explained in detail in the coming section.
Icon
Description
Shortcuts
Allows users to configure short cut to quickly access programs with a few tabs.
Camera
Allows users take a picture or record a video. User can also adjust setting related to
camera in this menu option.
Device
ON/OFF
Enables/disables tablet computer’s hardware functions. The configurable functions are
Wi-Fi, WWAN (3G/4G/LTE), GPS, Bluetooth, Camera, LED indicators, Barcode Reader,
RFID Reader, and GPS Antenna routing options.
Settings
Provides users information such as PC Information, Battery status, and also device
settings such as power management setting, and function key mappings.
14
8-inch Rugged Windows Tablet M900P Quick Start Guide M101P
3.2 Using the Camera
To take photos or videos:
1. Open the Hottab application. The on-screen Hottab Camera Indicator lights orange.
2. Point the camera at an object.
3. Touch the on-screen shutter button to take a photo or video record button to record a video.
This Hottab menu option allows users take a picture or record a video. Before use, make sure the camera
is powered on under Devices ON/OFF menu with the following scenarios.
3.3 Changing Touch Mode
The tablet computer supports three built-in operating modes for different usage scenarios:
Mode
Usage Scenario
Hand/Rain
(Default)
In Hand/Rain mode the touchscreen rejects false inputs from liquid drops. When
the liquid is removed, the touchscreen accepts touch inputs from bare fingertips.
Supports input by:
Active stylus with palm rejection
Rubber tip passive stylus
Bare fingertips
Stylus
In Stylus mode, the touchscreen supports inputs from the fine-tip passive
capacitive stylus (shipped with tablet).
Support input by:
Fine-tip passive stylus with palm rejection
Active stylus with palm rejection
Rubber tip passive stylus
Bare fingertips
Glove
In Glove mode, the touchscreen supports inputs while the user is operating the
touchscreen with gloves on.
Supports input by:
Glove
Rubber tip passive stylus
Bare fingertips
To change touch mode:
a. Shortly press Function Key 1 (To define the function key refer to User Manual, Chapter 4).
15
Quick Start Guide
b. Press (Menu) button on the front to open HotTab, or launch HotTab Utility application. Choose
“Device ON/OFF, and then click “Touch Set” icon.
3.5 Scanning Barcodes
Depending upon configuration, barcode scanning can be performed using the built-in1D/2D barcode
scanner (Note: barcode scanner is an optional feature).
To set up a barcode scanner:
1. Tear off protective film from the barcode.
2. Press Menu to open Hottab utility.
3. Choose Device ON/OFF and click on Barcode
.
4. Tap barcode power ON.
5. Press button located on the rear.
6. Scan a barcode to check your reader is working
properly. Result will be displayed in Hottab.
3.6 Reading RFID Tags
Depending upon configuration, the M101P supports reading RFID tags. The RFID antenna is located on the
back of the device under the RFID logo.
To enable RFID Reader:
1. Press Menu to open Hottab utility.
2. Choose Device ON/OFF and
click on RFID.
3. Tap on the ON button. The button
turns green, and the RFID icon in the
Hottab menu is orange.
4. Bring the RFID card toward the
antenna. Result will be displayed in
Hottab
16
8-inch Rugged Windows Tablet M900P Quick Start Guide M101P
3.7 Reading MSR/ EMV Cards
The MSR/ EMV Card Reader is an optional feature of M900P tablet and is designed to allow magnetic
stripe (MSR) card transactions and ICC (Chip) card transactions from your tablet computer.
To use this feature, please make sure your tablet has built-in MSR/ EMV card reader before use, or contact
our sales department for more details.
To read magnetic strip card MSR card swipe the card.
To read EMV card insert the card into the EMV reader located on the right side.
The Universal SDK comes with a rich, fully featured demo app, complete source code for the demo app is
included with the SDK.
17
Quick Start Guide
3.8 Basic Troubleshooting
Problem
Solution
The removable battery is not
charging.
Make sure the AC adapter is properly connected, and that
the removable battery is properly inserted.
Nothing appears on the screen.
The tablet computer may be in sleep mode. Press the power
button to wake up the display.
The brightness level may be too low. Increase brightness.
The screen suddenly turns blank
and the power indicator goes off.
Make sure that LED indicator is not powered off in Hottab.
Make sure the AC adapter is properly connected.
If running on battery power, the battery may be depleted,
charge the battery.
Wireless LAN signal quality is
poor.
The tablet computer may be out of range. Move the tablet
computer closer to the access point or another wireless LAN
device associated with it.
Check if your surroundings have interferences, such as
microwave ovens, cordless phones. Move the tablet
computer away from objects causing interference.
I cannot connect to another
wireless LAN device.
Make sure that wireless LAN feature is powered on.
Make sure that the SSID setting is the same for every
wireless LAN device in the network.
Restart the tablet computer
Make sure the IP address or subnet mask setting is correct.
I cannot connect to another
device with Bluetooth.
Make sure that both devices have Bluetooth powered on
(For the Tablet Computer, check Hottab to see if Bluetooth
is powered on).
Make sure that the distance between the two devices is
within 10 meters and there are no walls or large obstructions
between the devices.
Make sure the both devices are powered on and configured
to be discoverable.
Make sure that both devices are compatible.
The GPS application cannot find
my location.
Make sure that GPS is powered on in Hottab.
Make sure that GPS receiver and the location sensor are
enabled in Control Panel.
The tablet computer may be out of coverage area. Move
your tablet computer outdoors or closer to a window.
Check if your surroundings have interferences, such as
microwave ovens, cordless phones. Move the tablet
computer away from objects causing interference.
No sound is produced.
Adjust volume of the tablet computer by pressing on the
volume rocker.
If using an external audio device, make sure that the cable
is properly connected.
I cannot project the tablet
computer display to another
monitor.
Make sure the VGA driver is installed.
Make sure the output setting selected is correct.
18
8-inch Rugged Windows Tablet M900P Quick Start Guide M101P
Problem
Solution
Barcode scanner does not emit
laser beam and does not seem to
work.
Make sure the Barcode scanner device is enabled in
Hottab utility.
Make sure under Windows, the Barcode Reader is set to
COM 15 port, so that Hottab can trigger the Barcode
Reader hardware.
Barcode scanner emits laser beam
but does not read barcode
presented to it.
Adjust the distance between barcode scanner of the
device and the barcode being scanned.
Make sure the barcode code type is enabled in the
tablet. To enable/disable a specific barcode code type,
go through the “Barcode Scanner Configuration” section.
I am having GPS accuracy issue
When utilizing the GPS function, we recommend
disabling the Barcode Reader in Hottab to reduce
interference.
RFID scanner does not seem to
work.
Make sure under Windows, the RFID hardware is set to
COM 3 port.
Battery leaking or swollen
The lithium battery used in this tablet may swell after
being charged/ discharged many times, but there is no
problem regarding safety.
Continued use in such a state may result in the battery
getting jammed, so please stop using the battery, and
purchase a new one.
19
Quick Start Guide
Chapter 4: In-Vehicle Applications
4.1 Installing Vehicle Cradle
Use a vehicle cradle to mount a tablet on the vehicle. Follow the instructions below to install M900P rugged
tablet on the vehicle cradle.
Highlights:
•Keeps the tablet securely fastened on a moving vehicle
• Anti-theft design with key lockable cradle
• Wide power voltage input (9~36V DC)
• VESA standard for various mounting fixtures
Installation Instruction:
❶ Place a tablet on the vehicle cradle.
❷ Make sure the tablet is firmly inserted into the
cradle.
❸ Use RAM mount to install the vehicle mount on
the windshield or other flat car surface. Notice
that RAM mount kit is not supplied by Winmate.
Reverse the procedure to detach a tablet from the vehicle cradle.
20
8-inch Rugged Windows Tablet M900P Quick Start Guide M101P
4.2 Installing Vehicle Gateway VG-100
The VG-100 is a gateway in a waterproof IP-65 rated enclosure designed to be integrated into vehicles. It
provides communications across in-vehicle by the CANbus, RS-485 and GPIO interfaces. It can also
control I/O based upon message and signals received from the vehicle network.
Vehicle Application Diagram
La page charge ...
La page charge ...
La page charge ...
La page charge ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24

Winmate M900P Guide de démarrage rapide

Marque
Winmate
Modèle
M900P
Catégorie
Comprimés
Taper
Guide de démarrage rapide
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents