Unbranded R6GP Guide d'installation

Marque: Unbranded

Modèle: R6GP

Taper: Guide d'installation

Ce manuel convient également à

R6GP 6, 7.5 - 10 Ton Archived 2/23/12

R6GP - 072/090/120 Series, A Revision

Installation Instructions

Single Package Gas Heating / Electric Cooling Rooftop Units

R6GP-090 Shown

DO NOT DESTROY THIS MANUAL. KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.

FIRE OR EXPLOSION HAZARD

•Failure to follow safety warnings exactly

could result in serious injury or property

damage.

•Installationandservicemustbeperformed

byaqualiedinstaller,serviceagencyorthe

gas supplier.

•Do not store or use gasoline or other

ammablevaporsandliquidsinthevicinity

ofthisoranyotherappliance.

WHAT TO DO IF YOU SMELL GAS

•Donottrytolightanyappliance.

•Donottouchanyelectricalswitch;donot

useanyphoneinyourbuilding.

•Leavethebuildingimmediately.

•Immediatelycall yourgassupplierfroma

neighbor’sphone.Followthegassupplier’s

instructions.

•Ifyoucannotreachyourgassupplier,call

theredepartment.

WARNING:

RISQUED’INCENDIEOUD’EXPLOSION

•Le non-respect des avertissements de

sécurité pourrait entraîner des blessures

graves, la mort ou des dommages matériels.

•L’installation et l’entretien doivent être

effectués par un installateur qualié, un

organisme de service ou le fournisseur de

gazstaller,serviceagencyorthegassupplier.

•Nepasentreposerniutiliserdel’essenceni

d’autres vapeurs ou liquides inammables

dans le voisinage de cet appareil, ni de tout

autre appareil.

QUEFAIRES’ILYAUNEODEURDEGAZ

•Nepastenterd’allumeraucunappareil.

•Netoucheràaucuninterrupteurélectrique;

n’utiliseraucuntéléphonedanslebâtiment.

•Évacuerl’immeubleimmédiatement.

•Appeler immédiatement le fournisseur de

gazenemployantletéléphoned’unvoisin.

Respecter à la lettre les instructions du

fournisseur de gaz.

•Sipersonnenerépond,appelerleservicedes

incendies.

AVERTISSEMENT

IMPORTANT SAFETY INFORMATION .......................3

REQUIREMENTS & CODES .......................................4

GENERAL INFORMATION ..........................................5

About the Rooftop Unit ..............................................5

Before You Install This Equipment .............................5

Locating the Unit .......................................................5

Heating Load .............................................................5

COMBUSTION AIR & VENTING..................................6

Vent Termination ........................................................6

CIRCULATING AIR SUPPLY .......................................7

Downﬂow to Horizontal Conversion ...........................7

Unconditioned Spaces ..............................................7

Acoustical Ductwork ..................................................7

Air Filter Requirements..............................................8

UNIT INSTALLATION ..................................................8

Packaging Removal ...................................................8

Rigging & Hoisting .....................................................8

Minimum Clearance Requirements ...........................8

Rooftop Mounting ......................................................9

Ground Level .............................................................9

Condensate Drain ...................................................10

GAS SUPPLY & PIPING ............................................10

Leak Check .............................................................11

High Altitude Deration .............................................11

Conversion to LP/Propane ......................................12

ELECTRICAL WIRING ............................................... 13

Pre-Electrical Checklist ...........................................13

Line Voltage ............................................................. 13

Grounding................................................................13

Unbalanced 3-Phase Supply Voltage ......................14

Thermostat / Low Voltage Connections ................... 14

Heat Anticipator ....................................................... 14

Blower Speed ..........................................................14

STARTUP & ADJUSTMENTS ...................................15

Pre-Start Check List ................................................15

Startup Procedures .................................................15

Air Circulation ..........................................................15

System Cooling .......................................................15

System Heating .......................................................15

Verifying & Adjusting Temperature Rise ..................16

Verifying Burner Operation ......................................16

Verifying Operation of Over-Temperature

Limit Control ............................................................16

Verifying & Adjusting Firing Rate ............................. 16

Manifold Pressure Adjustment ................................17

Refrigerant Charging ...............................................17

OPERATING SEQUENCE .........................................17

Cooling Mode ..........................................................17

Heating Mode ..........................................................17

Blower Mode ...........................................................18

UNIT MAINTENANCE ................................................18

Routine Maintenance ..............................................18

Cleaning of Burners ................................................19

Cleaning of Heat Exchanger ...................................19

COMPONENT FUNCTIONS ......................................20

TROUBLESHOOTING ...............................................21

FIGURES & TABLES .................................................22

Physical Dimensions ...............................................22

Figure 12 - 072 Series .........................................22

Figure 13 - 090 Series .........................................24

Figure 14 - 120 Series .........................................26

Table 3 - Unit Shipping Weights ...........................27

Blower Performance Data .......................................28

Table 4- R6GP Alt. Accessory Blower Drives .......28

Table 5 - 072C - 100C Series - Downﬂow ............29

Table 6 - 072C - 100C Series - Horizontal ...........30

Table 7 - 072C -166C Series - Downﬂow .............31

Table 8 - 072C - 166C Series - Horizontal ...........32

Table 9 - 090C - 200Ca Series - Downﬂow ..........33

Table 10 - 090C - 200Ca Series - Horizontal .......34

Table 11 - 120C - 235Ca Series - Downﬂow ........35

Table 12 - 120C - 235Ca Series - Horizontal .......36

Electrical Information ............................................... 37

Table 13 - Electrical Data .....................................37

Figure 15 - Ladder Diag. - 072/090/120 Series ....38

Figure 16 - W.D. - 072/090/120 Series .................39

Gas Information ....................................................... 40

Table 14 - Gas Pipe Capacities ............................ 40

Table 15 - Oriﬁce or Drill Sizes ............................. 40

Table 16 - Heating Rise/Range ............................40

Table 17 - Gas Flow Rates ...................................41

R6 Charging Charts ................................................42

Figure 17 - R6GP-072 Series ..............................42

Figure 18 - R6GP-090 Series ..............................43

Figure 19 - R6GP-120 Series ..............................43

R6 Gas Valve Labels ...............................................44

Figure 20 - 6 & 7.5 Ton Units ...............................44

Figure 21 - 10 Ton Units .......................................45

INSTALLATION CHECKLIST ....................................48

TABLE OF CONTENTS

IMPORTANT SAFETY INFORMATION

Please read all instructions before servicing this equipment.

Pay attention to all safety warnings and any other special

notes highlighted in the manual. Safety markings are used

frequently throughout this manual to designate a degree

or level of seriousness and should not be ignored.

WARNING indicates a potentially hazardous situation

that if not avoided, could result in personal injury or death.

CAUTION indicates a potentially hazardous situation that

if not avoided, may result in minor or moderate injury or

property damage.

ATTENTION INSTALLERS: It is your responsibility to

know this product better than your customer. This includes

being able to install the product according to strict safety

guidelines and instructing the customer on how to operate

and maintain the equipment for the life of the product.

Safety should always be the deciding factor when installing

this product and using common sense plays an important

role as well. Pay attention to all safety warnings and any

other special notes highlighted in the manual. Improper

installation of the unit or failure to follow safety warnings

could result in serious injury, death, or property damage.

These instructions are primarily intended to assist qualiﬁed

individuals experienced in the proper installation of this

appliance. Local codes may require licensed installation/

service personnel for this type of equipment. After

completing the installation, return these instructions to

the customer’s package for future reference.

WARNING:

Improper installation, service, adjustment,

or maintenance may cause explosion, re,

electricalshockorotherhazardousconditions

whichmayresultinpersonalinjuryorproperty

damage. Unless otherwise noted in these

instructions, only factory authorized kits or

accessoriesmaybeusedwiththisproduct.

WARNING:

Donotplacecombustiblematerialonoragainst

the unit cabinet. Do not place combustible

materials, including gasoline and any other

ammablevaporsandliquids,in thevicinity

oftheunit.

WARNING:

PROPOSITION 65 WARNING: This product

contains berglass wool, a product known

to the state of California to cause cancer.

Disturbingtheinsulationofthisproductduring

installation,maintenance,orrepairwillexpose

youtoberglasswool.

• Breathingthismaterialmaycauserespiratory

irritationsormaycauselungcancer.

•Fiberglass wool may also cause eye

irritation,skinsensitization,orotherallergic

responsesinsusceptibleindividuals.

• Always wear goggles, disposable gloves,

longsleevedshirt,andappropriatebreathing

protectionwhenworkingnearthisinsulation.

Ifcontactwithskinoccurs,washimmediately

withsoapandwater.Incaseofcontactwith

eyes, ush immediately with water for at

least15minutes.Contactaphysicianifneeded.

WARNING:

The information listed below and must be

followed during the installation, service,

and operation of this unit. Unqualified

individualsshouldnotattempttointerpretthese

instructionsorinstallthisequipment.Failure

tofollowsafetyrecommendationscouldresult

inpossibledamagetotheequipment,serious

per

sonalinjuryordeath

• Thisequipmentcontainsliquidandgaseousrefrigerant

under high pressure. Installation or servicing should only

be performed by qualiﬁed trained personnel thoroughly

familiar with this type equipment.

• Before beginning the installation, verify that the unit

model is correct for the job. The unit model number

is printed on the data label. Follow all precautions in

the literature, on tags, and on labels provided with

the equipment. Read and thoroughly understand

the instructions provided with the equipment prior to

performing the installation and operational checkout

of the equipment.

• Never test for gas leaks with an open ame. Use a

commercially available soap solution to check all

connections See page 11.

• Follow all precautions in the literature, on tags, and

on labels provided with the equipment. Read and

thoroughly understand the instructions provided with

the equipment prior to performing the installation and

operational checkout of the equipment.

• Thisunitisdesignedonlyforoutdoorinstallationsand

should be located with consideration of minimizing the

REQUIREMENTS & CODES

• Thisequipmentmustbeinstalledinaccordancewith

instructionsoutlinedinthismanual,allapplicable

local buildingcodes,and the current revisionof

theNationalFuelGasCode(NFPA54/ANSIZ223.1)

ortheNaturalGasandPropaneInstallationCode,

CAN/CGA B149.1.

• Allelectricalwiringmustbecompletedinaccordance

with local, state and national codes and regulations and

withtheNationalElectricCode(ANSI/NFPA70)orin

Canada the Canadian Electric Code Part 1 CSA C.22.1.

• The installer must comply with all local codes and

regulations which govern the installation of this type

of equipment. Local codes and regulations take

precedence over any recommendations contained in

these instructions. Consult local building codes and the

NationalElectricalCode(ANSICI)forspecialinstallation

requirements.

• Air Ducts must be installed in accordance with the

standardsoftheNationalFireProtectionAssociation

“Standards for Installation of Air Conditioning and

Ventilation Systems” (NFPA 90A), “Standard for

Installation of Residence Type Warm Air Heating and Air

ConditioningSystems”(NFPA90B),theseinstructions,

and all applicable local codes.

• ConsultTable16(page40),andtheratingplateforthe

proper circulating air ﬂow and temperature rise. It is

important that the duct system be designed to provide

the correct ﬂow rates and external pressure rise. An

improperly designed duct system can result in nuisance

shutdowns, and comfort or noise issues.

• Thisunitisdesignedforoutdoorinstallationsonlyand

should be located as described on page 5.

• Use only with the type of gas approvedforthis unit.

Refer to the unit rating plate.

• Provideadequatecombustionandventilationairtothe

unit. See pages 6 & 7.

• Provideadequateclearancesaroundtheairventintake

terminal as speciﬁed on page 6.

length of the supply and return ducts. Consideration

should also be given to the accessibility of fuel, electric

power, service access, noise, and shade.

• Theinstallershouldbecomefamiliarwiththeunitswiring

diagram before making any electrical connections to the

unit.SeetheunitwiringlabelorFigures15&16(pages

38&39).

• Usecautionwhenhandlingthisapplianceorremoving

components. Personal injury can occur from sharp metal

edges present in all sheet metal constructed equipment.

Combustion&VentilationAir

• US: National Fuel Gas Code (NFGC), Air for

Combustion and Ventilation

• CANADA: Natural Gas and Propane Installation

Codes(NSCNGPIC),VentingSystemsandAirSupply

for Appliances

DuctSystems

• US and CANADA: Air Conditioning Contractors

Association (ACCA) Manual Q, Sheet Metal and

Air Conditioning Contractors National Association

(SMACNA), or American Society of Heating,

Refrigeration, and Air Conditioning Engineers

(ASHRAE)FundamentalsHandbook

Electrical Connections

• US:NationalElectricalCode(NEC)ANSI/NFPA70

• CANADA:CanadianElectricalCodeCSAC22.1

Gas Piping & Gas Pipe Pressure Testing

• US:NFGCandNationalPlumbingCodes

• CANADA:NSCNGPIC

General Installation

• US:CurrenteditionoftheNFGCandtheNFPA90B.

For copies, contact the National Fire Protection

Association Inc., Batterymarch Park, Quincy, MA

02269;orAmericanGasAssociation,400N.Capitol,

N.W.,WashingtonDC20001orwww.NFPA.org.

• CANADA:NSCNGPIC.Foracopy,contactStandard

Sales, CSA International, 178 Rexdale Boulevard,

Etobicoke(Toronto),Ontario,M9W1R3Canada

Safety

• US:(NFGC)NFPA54–1999/ANSIZ223.1andthe

Installation Standards, Warm Air Heating and Air

ConditioningSystemsANSI/NFPA90B.

• CANADA:CAN/CGA-B149.1–and.2–M00National

StandardofCanada.(NSCNGPIC)

• Combustion products must be discharged outdoors.

Connect this unit to an approved vent system only, as

speciﬁed on page 6.

• Additionalcodeslistedbelowareforreferencepurposes

only and do not necessarily have jurisdiction over

local or state codes. Local codes and regulations take

precedence over any recommendations contained in

these instructions. Always consult with local authorities

before installing any gas appliance.

GENERAL INFORMATION

AbouttheRooftopUnit

Single Package Gas Heating / Electric Cooling Rooftop

Units are designed only for outdoor rooftop or ground level

installations and can be readily connected to the duct

system of a building. This unit has been tested for capacity

and efﬁciency in accordance with AHRI Standards and

will provide many years of safe and dependable comfort,

providing it is properly installed and maintained. With

regular maintenance, this unit will operate satisfactorily

year after year. Abuse, improper use, and/or improper

maintenance can shorten the life of the appliance and

create unsafe hazards.

To achieve optimum performance and minimize equipment

failure, it is recommended that periodic maintenance be

performed on this unit. The ability to properly perform

maintenance on this equipment requires certain tools

and mechanical skills.

BeforeYouInstallthisEquipment

√ The cooling load of the area to be conditioned must be

calculated and a system of the proper capacity selected.

It is recommended that the area to be conditioned be

completely insulated and vapor sealed.

√ Check the electrical supply and verify the power supply

is adequate for unit operation. Consideration should be

given to availability of electric power, service access,

noise, and shade. If there is any question concerning

the power supply, contact the local power company.

√ All units are securely packed at the time of shipment and

upon arrival should be carefully inspected for damage

prior to installing the equipment at the job site. Verify

coil ﬁns are straight. If necessary, comb ﬁns to remove

attenedorbentns.Claimsfordamage(apparentor

concealed)shouldbeledimmediatelywiththecarrier.

√ Please consult your dealer for maintenance information

and availability of maintenance contracts. Read all

instructions before installing the unit.

LocatingtheUnit

• Surveythejobsitetodeterminethebestlocationfor

the packaged unit. The unit should be located with

consideration of minimizing the length of the supply

and return ducts. If practical, place the equipment and

its ducts in an area where they will be shaded from

the afternoon sun, when the heat load is greatest.

Consideration should also be given to the accessibility

of fuel, electric power, service access, noise, and shade.

• Selectasolid,levelposition,preferablyonaconcrete

slab, slightly above the grade level, and parallel to the

building.

• Overhead obstructions, poorly ventilated areas, and

areas subject to accumulation of debris should be

avoided. Do not place the unit in a conﬁned space or

recessed area where discharge air from the unit could

re-circulate back through the condenser coil.

• Sufcientclearanceforunobstructedairowthroughthe

louvered control access panel and outdoor coil must be

maintained in order to achieve rated performance. See

pages 8 - 9 for minimum clearance requirements.

• Where accessibility to combustibles clearances

aregreaterthanminimumclearances,accessibility

clearances must take preference.

• Ifpractical,placetheairconditioneranditsductsinan

area where they will be shaded from the afternoon sun,

when the heat load is greatest.

Heating Load

This unit should be sized to provide the design heating

load requirement. Heating load estimates can be made

using approved methods available from Air Conditioning

ContractorsofAmerica(ManualN);AmericanSocietyof

Heating, Refrigerating, and Air Conditioning Engineers;

or other approved engineering methods. For installations

above 2,000 ft., the unit should have a sea level input

rating large enough that it will meet the heating load after

deration for the installed elevation.

COMBUSTION AIR & VENTING

WARNING:

Installationmethodsotherthanthosedescribed

inthefollowingsectionsmustcomplywiththe

NationalFuelGasCodeandallapplicablelocal

codesforprovidingsufcientcombustionair

tothefurnace.

Provisions must be made during the installation of this

unit that provide an adequate supply of air for combustion.

• Instructions for determining the adequacy of an

installation can be found in the current revision of the

NFGC(ANSIZ223.1/NFPA54).Consult local codes

forspecialrequirements. These requirements are for

USinstallationsasfoundintheNFGC.

• TherequirementsinCanada(B149.1)arestructured

differently. Consult with B149.1 and local code ofﬁcials

for Canadian installations.

WARNING:

Combustion air must not be drawn from a

contaminatedatmosphere.Excessiveexposure

tocontaminatedcombustionairwillresultin

safetyandperformancerelatedproblems.

To maximize heat exchanger life, the combustion air

must be free of chemicals that can form corrosive acidic

compounds in the combustion gases. The recommended

source of combustion air is to use clean air from outside.

DONOTplaceanychemicalswithammableorcaustic

vaporsortheseothercorrosivechemicalsnearthe

vent termination:

• Gasoline/Kerosene

• Permanentwavesolutions

• Chlorinatedwaxesandcleaners

• Chlorinebasedswimmingpoolchemicals

• Watersofteningchemicals

• De-icingsaltsorchemicals

• Carbontetrachloride

• Halogentyperefrigerants

• Cleaningsolvents

• Cements,glues,paintremovers,varnishes,etc.

• Hydrochloricacid

• Masonryacidwashingmaterials

• PlumbingStack

Air openings in the door of the unit, warm air registers, and

return air grilles must never be restricted. If the unit does

not receive an adequate supply of air for combustion, the

ﬂame roll-out control located above the burners will open,

turning off the gas supply to the burners. This safety device

is a manually reset switch. IMPORTANT NOTE: DO NOT

installjumperwiresacrossthiscontroltodefeatits

functionorresetthecontrolwithoutidentifyingand

correctingthefaultcondition.

If this control must be replaced, use only factory authorized

replacement parts speciﬁed in the Replacement Parts

List provided online.

Vent Termination

This unit has been equipped with an integral venting

system and designed to operate only with this venting

system. If desired, an accessory venting kit is available.

UseonlyNORDYNEapprovedventingkitlistedinthe

technicalserviceliterature.

WARNING:

Thisunitis intendedforoutdoor installation

only.Donotventtheunitthroughaconventional

ventingsystem.

A vent cover assembly has been supplied with the unit

and can be found secured to the gas controls within the

burner area of this unit. Figure 1 displays the proper

installation of the vent cover assembly over the vent outlet

of the corner panel. The fasteners used to secure the vent

cover assembly have been included on the unit end panel.

The list below summarizes the location requirements for

theventingsystemtermination:

• Thelocationoftheventterminationmustbeconsistent

withtheNationalFuelGasCode(ANSIZ223.1)orCAN/

CGA-B149 Installation Codes.

• Mustbe locatedatleast4feethorizontallyfromany

electric meters, gas meters, regulators, and relief

equipment.

• Mustbelocatedatleast3feetaboveanyforcedairinlet

located within 10 feet of unit.

• Mustbelocatedatleast4feetbelow,4feethorizontally

from, or 1 foot above any door, window, or gravity air

inlet into any building.

• Mustbelocatedatleast1footabovegradeandinstalled

in such a manner as to prevent snow accumulation from

obstructing the vent termination.

• Theventterminationmustnotbelocatedaboveany

public walkways.

• Theventcoverassemblymustbeinstalledtoassure

proper operation of the unit.

Figure1.VentCoverAssembly

• Makesuretheexhaustgaseswillnotimpingeonwindows

or building surfaces, which may be compromised or

damaged by condensation.

• Donotinstalltheunitinalocationwhereexhaustfrom

the vent termination will be directed into windows,

stairwells, under decks, or other recessed areas.

CIRCULATING AIR SUPPLY

WARNING:

Donotallowcombustionproductstoenterthe

returnairductworkorthecirculatingairsupply.

Failuretopreventthecirculationofcombustion

products into the living space can create

potentially hazardous conditions including

carbonmonoxidepoisoningthatcouldresult

inpersonalinjuryordeath.

Allreturnductworkmustbesecuredtotheunit

withsheetmetalscrews.Allreturnductwork

mustbeadequatelysealedandalljointsmust

betaped.Whenreturnairisprovidedthrough

thebottomoftheunit,thejointbetween the

unitandthereturnairplenummustbeairtight.

Theroofcurborcementpadonwhichtheunitis

mountedmustprovidesoundphysicalsupport

of the unit with no gaps, cracks, or sagging

betweentheunitandthecurborpad.

Returnairandcirculatingairductworkmustnot

beconnectedtoanyotherheatproducingdevice

suchasareplaceinsert,stove,etc.Doingso

mayresultinre,explosion,carbonmonoxide

poisoning,personalinjury,orpropertydamage.

This unit is designed only for use with a supply and return

duct. Air ducts should be installed in accordance with the

standards of the National Fire Protection Association

“Standard for Installation of Air Conditioning Systems”

(NFPA90A),“StandardforInstallationofResidenceType

WarmAirHeatingandAirConditioningSystems”(NFPA

90B),andallapplicablelocalcodes.NFPApublicationsare

availablebywritingto:NationalFireProtectionAssociation,

BatterymarchPark,Quincy,ME02269orvisitwww.NFPA.

org on the web.

• DesigntheductworkaccordingtoManualQbytheAir

ConditioningContractorsofAmerica(ACCA)orsimilar

commercial methods.

• Ifroof curb is installed, the ducts must be attached to

the curb hangers, not the unit.

• Duct work should be attached directly to the unit ﬂanges

for horizontal applications.

• It is recommended that the outlet duct be equipped

with a removable access panel. This opening should

be accessible when the unit is installed in service and

shall be of a size such that the smoke or reﬂected

light may be observed inside the casing to indicate the

presence of leaks in the heat exchanger. The cover for

the opening shall be attached in such a manner as to

prevent leaks.

• If outside air is utilized as return air to the unit for

ventilation or to improve indoor air quality, the system

must be designed so that the return air to the unit is

notlessthan50°F(10°C)duringheatingoperation.

• Ifacombinationofindoorandoutdoorairisused,the

ducts and damper system must be designed so that the

return air supply to the furnace is equal to the return air

supply under normal, indoor return air applications.

• This unit is shipped ready for downflow duct

connections and is easily converted for horizontal

duct connections with an optional accessory kit.

See the unit Technical Sales Literature for factory

and ﬁeld installed accessory information and part

numbers. This information can also be found online at

www.nordyne.com.

DownowtoHorizontalConversion

The unit is shipped ready for downﬂow duct connections. If

horizontal ducts are required, the unit must be converted

according to the directions in the conversion kit for both

the supply and return ducts.

Always review the horizontal kit instructions prior to

changing the air temperature limits for horizontal operation

of the gas heat exchanger.

Unconditioned Spaces

All ductwork passing through unconditioned space must be

properly insulated to prevent condensation and minimize

duct losses. Use insulation with an outer vapor barrier.

Refer to local codes for insulation material requirements.

AcousticalDuctwork

Certain installations may require the use of acoustical

lining inside the supply duct work.

• Acoustical insulation must be in accordance with the

current revision of the Sheet Metal and Air Conditioning

ContractorsNationalAssociation(SMACNA)application

standard for duct liners.

• Duct lining must be UL classiﬁed batts or blankets with

a ﬁre hazard classiﬁcation of FHC-25/50 or less.

• Fiber duct work may be used in place of internal duct

liners if the ﬁber duct work is in accordance with the

currentrevisionoftheSMACNAconstructionstandard

on ﬁbrous glass ducts. Fibrous duct work and internal

acousticalliningmustbeNFPAClass1airductswhen

tested per UL Standard 181 for Class 1 ducts.

AirFilterRequirements

WARNING:

Neveroperatetheunitwithoutalterinplace.

Dust and lint could accumulate on internal

parts,resultinginlossofefciency,equipment

damageandpossiblere.

All return air must pass through the ﬁlters before entering

the unit. It is important that all ﬁlters be kept clean and

replaced frequently to ensure proper operation of unit.

Dirty or clogged ﬁlters will reduce the efﬁciency of the

unit and result in unit shutdowns. Air ﬁlter pressure drop

must not exceed 0.08 inches WC. When replacing the air

ﬁlters, a suitable air ﬁlter must be installed ahead of the

evaporator coil of the return air system. Refer to Table 1

for recommended ﬁlter sizes.

Figure3.BottomView

Crate Brackets (x4)

Long Bottom

Boards (x2)

Short Bottom

Boards (x2)

Base

Rails

Figure2.SideView

Wood Cap

Assembly

Top Crate

Brackets

Lower

Crate

Brackets

End Skid

Side Skids

UNIT

FACTORY

FILTER SIZE

QTY

R6GP-072*-(100/166)C 16x20x2 4

R6GP-090*-200C 16x20x2 4

R6GP-120*-235C 16x25x2 4

Table1.FilterSizes&Quantities

UNIT INSTALLATION

Packaging Removal

All units have been securely packaged at the point of

shipment. After unpacking the unit, carefully inspect for

apparent and concealed damage. Claims for damage

should be ﬁled with the carrier by the consignee.

1. Remove top crate brackets and wooden cap assembly

fromtopofunit(Figure2).

2. Remove lower crate brackets, 4 side skids, and 2 end

skids from each side of unit. NOTE: DO NOT remove

baserailsfromunit.

3. Rig unit and raise up approximately 4 feet off the ground.

4.Removecratebrackets(Figure3)securinglongand

short bottom boards to underside of unit. NOTE: Some

screwsarelocatedinforkslots.

5. Remove long & short bottom boards from beneath unit.

6. Inspect unit thoroughly for shipping damage.

7. Carefully lower and position unit to it’s permanent

location.

Rigging & Hoisting

WARNING:

Toavoidtheriskofpropertydamage,personal

injury,ordeath,itistherigger’sresponsibility

toensurethatwhatevermeansareusedtohoist

theunitaresafeandadequate:

• Theliftingequipmentmustbeadequateforthe

load.RefertoTable3(page27)forunitweights.

• Theunitmustbeliftedfromtheholesinthe

baserailsusingcablesorchains.

• Spreaderbarsarerequiredtoprotecttheunit

and ensure even loading. See Figure 4.

• Keeptheunitinanuprightpositionatalltimes.

Theriggingmustbelocatedoutsidetheunits

centerofgravity.RefertoFigures12-14(pages

22-27)forlocatingthecenterofgravity.

• All panels mustbe securelyin place during

riggingandhoisting.

MinimumClearanceRequirements

R6GP units are certiﬁed as combination heating and

cooling equipment for outdoor installation only. Figure 5

(page9)displaystheminimumclearancestocombustible

materials for both Downﬂow and Horizontal discharge.

R6GP units may be installed on non-combustible surfaces

when used with bottom supply and return air ducts.

Figure 4. Rigging & Hoisting

LIFTING

BEAM

CABLE OR CHAIN

SPREADER

BAR

SPREADER

BAR

BASE

RAIL

BASE

RAIL

Top of unit

to be

unobstructed

Recommended Clearances

for Servicibility

Minimum Required

Clearances to Combustibles

36"

48"

60"

48"

Figure5.UnitClearanceRequirements

Figure 7. Concrete Mounting Pad

3” min

Figure6.RoofCurb

Roof

Curb

Units may be installed on wood ﬂooring or on Class A,

B, or C roof covering material as long as the following

requirementsaremet:

• Ifusingsidesupplywithreturnairducts,thehorizontal

discharge kit must be installed prior to unit installation.

• Ifusingbottomdischargewithreturnairductsaroofcurb

must be installed prior to unit installation. See Rigging

and Hoisting section on page 8 for setting of the unit.

Rooftop Mounting

Rooftop installations must be located according to local

buildingcodesorordinancesandtheserequirements:

• The roof must be capable of handling the weight of the

unit.Forunitweights,seeTable3(page27).Reinforce

the roof if necessary.

• Theappropriateaccessoryroofcurb(Figure6)mustbe

installed prior to unit installation. The roof curb must be

square and level to ensure proper condensate drainage.

Pleasefollowallinstructionsprovidedwiththekit.

WARNING:

Neverdrillorpunchholesinunitbasewhen

installingdownowunits.Leakagemayoccur

ifbottompanispunctured.

• On bottom discharge applications, the supply and

return air ducts must be attached to the roof curb duct

supports, not the unit. Install all ductwork before setting

unit on curb or frame.

• Framesupportmustbeconstructedusingnoncombustible

materials. Full perimeter support is required under the

unit. Supports must be made of steel or weather resistant

wooden materials. The unit must be square and level

to ensure proper condensate drainage.

• Theframemustbehighenoughtoensureprevention

of any moisture from entering the unit. Recommended

heighttounitbaseis8”(20cm)forbothDownowand

Horizontal installations.

• Secure roof curb or frame to roof using acceptable

mechanical methods per local codes.

Ground Level

Ground level installations must be located according to

localbuildingcodesorordinancesandtheserequirements:

• Clearancesmustbeinaccordancewiththoseshown

in Figure 5.

• Aconcretemountingpad(Figure7)mustbeprovided

and separate from the building foundation. The pad

must be level to ensure proper condensate disposal

and strong enough to support the unit’s weight. The slab

heightmustbeaminimumof3”(8cm)abovegradeand

with adequate drainage.

• Units require horizontal supply and return kit for

horizontal installations.

• Ductwork should be attached directly to anges on

panels supplied in horizontal duct conversion kits.

Condensate Drain

The method for disposing of condensate varies according

to local codes. Consult your local code or authority having

jurisdiction.

Condensateisdrainedfromtheunitthrougha3/4”(19mm)

PVCpipelocatedonthefrontsideoftheunit(Figure8).

Forproperdrainage,installa3”(8cm)Min.trapbetween

the drain line and an open vent of the same size. Avoid

areas where condensate drainage may cause problems.

The condensate drain line must be J-trapped using ﬁeld

supplied parts and may be combined with other drain lines

when routed to the drain.

When connecting rigid drain line, hold any ﬁttings with a

wrench to prevent twisting. Donotovertighten!

3”

Min

Roof Curb

Condensate

Drain

Figure 8. Condensate Drain

FIRE OR EXPLOSION HAZARD

•Failuretofollowsafetywarningsexactly

couldresultinseriousinjuryorproperty

damage.

•Installationandservicemustbeperformed

byaqualiedinstaller,serviceagencyor

thegassupplier.

•Donotstoreorusegasolineorother

ammablevaporsandliquidsinthe

vicinityofthisoranyotherappliance.

WHAT TO DO IF YOU SMELL GAS

•Donottrytolightanyappliance.

•Donottouchanyelectricalswitch;donot

useanyphoneinyourbuilding.

•Leavethebuildingimmediately.

•Immediatelycallyourgassupplierfrom

aneighbor’sphone.Followthegas

supplier’sinstructions.

•Ifyoucannotreachyourgassupplier,call

theredepartment.

WARNING:

RISQUED’INCENDIEOUD’EXPLOSION

• Lenon-respectdesavertissementsdesécurité

pourraitentraînerdesblessuresgraves,lamort

ou des dommages matériels.

• L’installationetl’entretiendoiventêtreeffectués

par un installateur qualié, un organisme de

service ou le fournisseur de gazstaller, service

agencyorthegassupplier.

• Ne pas entreposer ni utiliser de l’essence ni

d’autresvapeursouliquidesinammablesdansle

voisinage de cet appareil, ni de tout autre appareil.

QUEFAIRES’ILYAUNEODEURDEGAZ

• Nepastenterd’allumeraucunappareil.

• Ne toucher à aucun interrupteur électrique;

n’utiliseraucuntéléphonedanslebâtiment.

• Évacuerl’immeubleimmédiatement.

• Appelerimmédiatementlefournisseurdegazen

employantletéléphoned’unvoisin.Respecterà

la lettre les instructions du fournisseur de gaz.

• Si personne ne répond,appeler le service des

incendies.

AVERTISSEMENT:

GAS SUPPLY & PIPING

IMPORTANT NOTES:

• Allgaspipingmustbeinstalledincompliancewith

localcodesandutilityregulations.Intheabsence

oflocalcodesthegaslineinstallationmustcomply

withthelatesteditionoftheNationalFuelGasCode

ANSI Z223.1 or CAN/CGA B149 Installation Codes.

• Somelocalcodesrequiretheinstallationofamanual

mainshut-offvalveandgroundjointunionexternal

tothefurnace.Theshut-offvalveshouldbereadily

accessibleforserviceand/oremergencyuseSee

Figure9(page12).Consultthelocalutilityorgas

supplier for additional requirements regarding

placementofthemanualmaingasshut-off.

• Gaspipingmustneverruninorthroughairducts,

chimneys,gasvents,orelevatorshafts.

• Compoundsusedtosealjointsongaspipingmust

beresistanttotheactionsofLPpropanegas.

• Themaingasvalveandmainpowerdisconnectto

thefurnacemustbeproperlylabeledbytheinstaller

incaseemergencyshutdownisrequired.

• An1/8inchNPTpluggedtapmustbeinstalledin

thegaslineimmediatelyupstreamofthegassupply

connectiontothefurnaceforusewhenmeasuring

thegassupplypressure.Theplugshouldbereadily

accessibleforserviceuse.

• Adriplegshouldbeinstalledintheverticalpipe

runtotheunit(Figure9).

This unit is shipped from the factory for natural gas

operation at sea level elevation and is equipped with a

#36oriceateachburner.Table14(page40),listsgas

pipe capacities for standard pipe sizes as a function of

length in typical applications based on nominal pressure

drop in the line.

This unit only has right side gas entry. When connecting

the gas, provide clearance between the gas supply line

and the entry hole in the unit’s casing to avoid unwanted

noise and/or damage to the unit. A typical gas service

hookupisshowninFigure9(page12).

LeakCheck

After the gas piping to the unit is complete, all connections

must be tested for gas leaks. This includes pipe connections

at the main gas valve, emergency shutoff valve and other

gas connectors.

The soap and water solution can be applied on each

joint or union using a small paintbrush. If any bubbling is

observed, the connection is not sealed adequately and

must be retightened. Repeat the tightening and soap

check process until bubbling ceases.

IMPORTANT NOTES:

• Ifpressuretestingthegassupplylinesatpressures

greaterthan1/2psig(14inchesWC),theunitmust

bedisconnectedfromthegassupplypipingsystem

topreventdamagetothegasvalve.

• Ifthetestpressureislessthanorequalto1/2psig

(14inchesWC),theunitmustbeisolatedfromthe

gassupplylinebyclosingthemanualshut-offvalve.

HighAltitudeDeration

High altitude application with this unit depends on the

installation altitude and the heating value of the gas. At

high altitudes, the heating value of natural gas is always

lower than the heating value at sea level.

All installations of this equipment must be made in

accordancewiththeNationalFuelGasCodeorwithlocal

jurisdiction codes. For installations at exactly 2,000 feet

in altitude or under, the installer does not need to derate

the heat exchanger performance. For any installation that

exceeds 2,000 feet, please see the following instructions

andexample:

WARNING:

Thereductionofinputratingnecessaryforhigh

altitudeinstallationmayonlybeaccomplished

withfactorysuppliedorices.Donotattemptto

drilloutoricesintheeld.Improperlydrilled

orices may cause re, explosion, carbon

monoxidepoisoning,personalinjuryordeath.

RISQUED’INDENDIEOUD’EXPLOSION

Le non-respect des avertissements de sécurité

pourraitd’entraînerdesblessuresgraves,lamort

ou des dommages matériels.

Ne jamais utiliser une flamme nue por

vérier la présence des fuites de gaz. Pour la

véricationdetouslesjoints,utiliserplutôtune

solution savonneuse commerciale fabriquée

spéciquementpurladétectiondesfuitesdegaz.

Unincendieouuneexplosionpeutentraînerdes

dommagesmatériels,desblessuresoulamort.

AVERTISSEMENT:

FIRE OR EXPLOSION HAZARD

Failuretofollowsafetywarningsexactlycould

resultinseriousinjuryorpropertydamage.

Nevertestforgasleakswithanopename.

Useacommerciallyavailablesoapsolution

madespecicallyforthedetectionofleaksto

checkallconnections.Areorexplosionmay

result causing property damage, personal

injuryorlossoflife.

WARNING:

• Ifinstallingthisunitabove2,000feet,theinputratemust

bereduced4%per1,000feetofaltitude(Example:12%

at3,000feet,16%at4,000feet,etc).Alwaysroundup

to the next highest value of 1,000. So an installation

at 3,120 feet is derated by 16% due to rounding up to

4,000. NOTE: This deration is necessary to compensate

for low atmospheric pressure at high altitudes. Generally

this will require obtaining the gas heating value from the

local gas utility and replacing the burner oriﬁces.

• Table15(page40)liststhecorrectoricesizetouse

at different altitudes. To determine the unit rating and

oriﬁce size, see the installation example.

• Afterchangingtheorices,itisrequiredthatyoumeasure

the gas input rate by clocking the gas meter and using

the local gas heating value. See section on Verifying

and Adjusting the Firing Rate on page 16.

 IMPORTANT NOTE: Observe the action of the

burnerstomakesurethereisnoyellowing,lifting

orashbackoftheame.

Conversion to LP/Propane

WARNING:

The furnace was shipped from the factory

equippedtooperateonnaturalgas.Conversion

to LP/propane gas must be performed by

qualied service personnel using a factory

supplied conversion kit. Failure to use the

properconversionkitcancausere,explosion,

propertydamage,carbonmonoxidepoisoning,

personalinjury,ordeath.

INSTALLATION EXAMPLE:

Elevation: ..................................................3,890 feet

TypeofGas: .................................................. Natural

Unit Model: ................................... R6GP-090C200C

At 4,000 feet, the unit needs to be derated by 4% for

each 1,000 feet of elevation. This equates to 16% or

less than the sea level rating of 200,000 Btu/h.

1. Determineunitinputrating:

 [200kx(100-16)%]=168,000Btuh.The required

heating rate for 3,890 feet is 168,000 Btu/h.

2. Determineoricesize:

 FromTable15(page40),ndtheUnitModelNumber.

Follow across the row and stop at the 2,000-4,000

elevation column. For this example, the oriﬁce size

displayed is #38. Install one #38 oriﬁce in every burner

and check ﬁring rate. In this example, the ﬁring rate

must not exceed 168,000 Btu/h.

Figure9.TypicalGasServiceConnection

1. All piping must comply with local codes, ordinances, and/or National Fuel Gas Codes.

2. A manual shutoff valve must be installed within 6 feet of this equipment.

3. Always include a drip leg in piping.

NOTES:

Gas Valve

Riser

3 in.

Minimum

Horizontal

Drop

Piped Gas Supply

Tubing Gas Supply

3 in.

Minimum

Horizontal

Drop

Gas Valve

3 in.

Min.

Riser

Piped Gas Supply

In the U.S., if installing the unit above 2,000 ft., refer

to Table 15 to determine the correct oriﬁce size. When

conversion is complete, verify the input rate is correct as

listed in the tables. Approved conversion kit must be used.

Pleasefollowtheinstructionsprovidedwitheachkit.

Line Voltage

• Electricalconnectionsmustbeincompliancewithall

applicable local codes and ordinances, and with the

currentrevisionoftheNationalElectricCode(ANSI/

NFPA 70). For Canadian installations the electrical

connections and grounding shall comply with the current

Canadian Electrical Code (CSA C22.1 and/or local

codes).

• Providepowersupplyfortheunitinaccordancewiththe

unit wiring diagram and the unit rating plate. The line

voltage to the unit should be supplied from a dedicated

branch circuit containing the correct fuse or circuit

breaker for the unit.

• Anelectricaldisconnectmustbelocatedwithinsight

ofandreadilyaccessibletotheunit. This switch shall

be capable of electrically de-energizing the outdoor unit.

See unit data label for proper incoming ﬁeld wiring. Any

other wiring methods must be acceptable to authority

having jurisdiction.

• Awiringdiagramislocatedontheinsidecoverofthe

control access panel of the outdoor unit. The installer

should become familiar with the wiring diagram before

making any electrical connections to the outdoor unit.

SeeFigures15&16(pages38&39).

• Ifanyoftheoriginalwiressuppliedwiththeunitmust

be replaced, they must be replaced with material of the

same voltage, gauge, and temperature rating.

• Connecttheline-voltageleadstotheterminalsonthe

contactor inside the control compartment.

• Useonlycopperwireforthelinevoltagepowersupply

to this unit. Use proper code agency listed conduit and

connector for connecting the supply wires. Use of rain

tight conduit is recommended.

• Unitsareshippedfromthefactorywiredfor230or460

volt operation. On 208-230V units being placed into 208

volt operation, remove the lead from the transformer

terminal marked 240V and connect it to the terminal

marked 208V.

• Overcurrentprotectionmustbeprovidedatthebranch

circuit distribution panel and sized as shown on the

unitratinglabelandaccordingtotheNationalElectric

Code and applicable local codes. NOTE: See the unit

rating plate for maximum circuit ampacity and maximum

overcurrent protection limits.

Grounding

WARNING:

Theunitcabinetmusthaveanuninterruptedor

unbrokenelectricalgroundtominimizepersonal

injuryifanelectricalfaultshouldoccur.Do not

use gas piping as an electrical ground

This unit must be electrically grounded in accordance

with local codes or, in the absence of local codes, with

theNationalElectricalCode(ANSI/NFPA70)ortheCSA

C22.1 Electrical Code. Use the grounding lug provided in

the control box for grounding the unit.

ELECTRICAL SHOCK, FIRE OR EXPLOSION

HAZARD

Failuretofollowsafetywarningsexactlycould

resultinseriousinjuryorpropertydamage.

Improper servicing could result in dangerous

operation, serious injury, death or property

damage.

• Before servicing, disconnect all electrical

powertofurnace.

• Whenservicingcontrols,labelallwiresprior

todisconnecting.Reconnectwirescorrectly.

• Verifyproperoperationafterservicing.

WARNING:

RISQUEDECHOCÉLECTRIQUE,D’INCENDIE

OUD’EXPLOSION

Le non-respect des avertissements de sécurité

pourrait entraîner

unfonctionnementdangereux

del’appareil,

desblessuresgraves,lamortou

des dommages matériels.

Un entretein incorrect pourrait entraîner un

fonctionnementdangereuxdel’appareil,des

blessuresgraves,lamortoudesdommages

matériels

• Couper toute alimentation électrique au

générateurd’airchaudavantdeprodéder

auxtravauxd’entretein.

• Aumomentdel’entretiendescommandes,

étiqueteztousleslsavantdelesdébrancher.

S’assurerdelesraccordercorrectement.

•S’assurer que l’appareil fonctionne

adéquatementaprésl’entretien.

AVERTISSEMENT:

ELECTRICAL WIRING

Pre-ElectricalChecklist

√ Verify that the voltage, frequency, and phase of the

supply source match the speciﬁcations on the unit rating

plate.

√ Verify that the service provided by the utility is sufﬁcient

to handle the additional load imposed by this equipment.

SeeTable13(page37)ortheunitwiringlabelforproper

high and low voltage wiring.

√ Verify factory wiring is in accordance with the unit wiring

diagram. Inspect for loose connections.

√ For 3 phase units always check the phase balance

(page14).

Example:

AB=451V

BC=460V

AC=453V

2. Determine the average voltage in the power supply.

3.Determinethemaximumdeviation:

4. Determine percent of voltage

imbalance by using the results

from steps 2 & 3 in the following

equation.

maxvoltage deviation

fromaverage voltage

=100 x

averagevoltage

% Voltage Imbalance

454

100

=1.32%

Example:

1. Measure the line voltages

of your 3-phase power

supply where it enters the

building and at a location

that will only be dedicated

totheunitinstallation(at

the units circuit protection

ordisconnect).

Unbalanced3-PhaseSupplyVoltage

Voltage unbalance occurs when the voltages of all phases

of a 3-phase power supply are no longer equal. This

unbalance reduces motor efﬁciency and performance.

Someunderlyingcausesofvoltageunbalancemayinclude:

Lack of symmetry in transmission lines, large single-phase

loads, and unbalanced or overloaded transformers. A

motor should never be operated when a phase imbalance

in supply is greater than 2%. Perform the following steps

todeterminethepercentageofvoltageimbalance:

In this example, the measured line voltages were

451, 460, and 453. The average would be 454 volts

(451+460+453=1,364/3=454).

Theamountofphaseimbalance(1.32%)issatisfactory

since the amount is lower than the maximum allowable

2%. Please contact your local electric utility company if

your voltage imbalance is more than 2%.

Example:

Fromthevaluesgiveninstep1,theBCvoltage(460V)

isthegreatestdifferenceinvaluefromtheaverage:

460-454=6

454-451=3

454-453=1

Highest Value

Figure10.Typical2-StageHeat/Cool

ThermostatConnection

Indoor

Thermostat

Sub-Base

Unit Low Voltage

Terminal

T-Stat Wire

Gauge

Recommended T-Stat Wire

Length-Ft.(UnittoT-Stat)

18 Ga. 0 - 60

16 Ga. 61 - 130

Field Supplied Wiring - - - - - Use Solid Class II Copper Wire

• Atwo-stageheating/coolingthermostatisrequiredfor

R6GP series units. Select a thermostat which operates

in conjunction with the installed accessories. See Figure

10 for proper wire gauge and their recommended lengths

for typical thermostat connections.

• The low voltage wires must be properly connected

to the units low voltage terminal block. Route 24V

control wires through the gas furnace side of the unit.

Recommended wire gauge and wire lengths for typical

thermostat connections are shown in Figure 10.

• Thethermostatshouldbemountedabout5feetabove

theooronaninsidewall.DONOTinstallthethermostat

on an outside wall or any other location where its

operation may be adversely affected by radiant heat from

ﬁreplaces, sunlight, or lighting ﬁxtures, and convective

heat from warm air registers or electrical appliances.

Refer to the thermostat manufacturer’s instruction sheet

for detailed mounting information.

Thermostat/LowVoltageConnections

• SinglePackageGasHeating/ElectricCoolingRooftop

Units are designed to operate with a 24 VAC Class II

control circuit. The control circuit wiring must comply

with the current provisions of the NEC (ANSI/NFPA

70)andwithapplicablelocalcodeshavingjurisdiction.

Thermostat connections should be made in accordance

with the instructions supplied with the thermostat.

Heat Anticipator

Verify if the thermostat being used for the installation has a

heat anticipator setting. This function allows the thermostat

to anticipate the space heating rate and time the burner

to shutoff accordingly. Always refer to the thermostat

manufacturers instructions for the correct settings.

BlowerSpeed

The blower speed is preset at the factory but must

be veriﬁed at each installation. For optimum system

performance and comfort, it may be necessary to change

the factory set speed. Refer to Blower Performance Data

(Tables5-12,pages29-36)forproperoperatingrange.

Always ensure drive belt is secure and tensioned properly.

Also inspect variable pitch sheaves for proper tightness

of the set screws

Startup Procedures

WARNING:

Thisunitisequippedwithcrankcaseheaters.

Allow 24 hrs for heating of the refrigerant

compressor crankcase prior to start up and

anytimethepowerhasbeenremovedformore

than 12 hrs. Failureto complymay result in

damage or cause premature failure of the

system.

• Checkall electricalwiring forloose connectionsand

tighten as required.

• Checkunitforreturnairltersandcondensatetrap.

• Closeallelectricaldisconnectstoenergizethesystem.

Air Circulation

1. Set thermostat system switch to OFF and the fan switch

toON.

2. Verify the blower motor runs continuously. Check for

airdeliveryattheregister(s).Ensurethatthereareno

obstructions at the registers or in the ductwork.

3. Set thermostat fan switch to AUTO and verify the blower

shuts down immediately.

NOTE: If blower is turning opposite of arrow direction,

shut off main power to the unit and switch any two ﬁeld

wires at the disconnect. DO NOT alter unit wiring.

SystemCooling

1. Set the thermostat system switch to COOL and the fan

switch to AUTO.

2. Lower the thermostat temperature switch below

room temperature and observe that the blower, both

compressorsandfans)energize.

3. Verify blower is turning in direction indicated by arrow

and air discharged at the register is cooler than room

temperature.

4. Verify HI and LO refrigerant pressures.

NOTE: If refrigerant pressures are abnormal and blower

is rotating in the opposite direction of the arrow, shut off

main power to the unit and switch any two ﬁeld wires at

the disconnect. Ensure proper rotation of the blower. DO

NOTalterunitwiring.Listenforanyunusualnoises.Locate

the source and correct as needed.

5. Allow the unit to run for several minutes. Set the

temperature selector above room temperature and

verify that the fan, blower, and compressors cycle off

with the thermostat.

SystemHeating

1. Set the thermostat to the lowest setting.

2. Follow the startup procedures on this page or the

operating instruction label inside the louvered control

access panel.

3. Set the thermostat above room temperature and verify

theOperatingSequence(page17).

CAUTION

Toavoidpersonalinjuryorpropertydamage,

makecertainthatthemotorleadsdonotmake

contactwithanyuninsulatedmetalcomponents

oftheunit.

Tochangetheblowerspeed:

1. Disconnect all electrical power to the unit and remove

the blower access panel.

2. Loosen the motor tension bars to allow removal of the

blower belt from the motor sheave.

3. Loosen top set screw on motor sheave and turn clockwise

toclose(increasesblowerspeed),orcounterclockwise

toopen(decreasesblowerspeed).

4. Replace belt on pulleys and position motor mounting

plate to correct position for proper belt tension.

5. Tighten tension bar bolts.

STARTUP & ADJUSTMENTS

Pre-StartCheckList

√ Verify unit is properly supported.

√ Verify unit is level for proper condensate drainage.

√ Verify all clearance requirements are met. Airﬂow to

and from the outdoor coil must be unrestricted.

√ Verify the ductwork is adequately sealed to prevent air

leakage. Insulate if necessary.

√ Verify the line voltage power leads are securely

connected and the unit is properly grounded.

√ Verify low voltage wires are securely connected to the

correct leads in the low voltage area of the control box.

√ Verify gas line pressure. For natural gas, the line pressure

mustnotexceed10.0inchesWC(0.36psig),orbeless

than5.5inchesWC(0.20psig).ForLPgas,theline

pressuremustnotexceed14inchesWC(0.51psig)

andmustnotbelessthan11.0inchesWC(0.40psig).

√ Verify the flame roll-out control is closed.

IMPORTANTNOTE:Thissafetydeviceisamanually

resetswitch.Ifnecessary,presstheredbuttonto

reset the control. DO NOT install a jumper wire

across the control to defeat its function. If the

controlreopensuponstart-up,DONOTresetthe

controlwithoutidentifyingandcorrectingthefault

conditionwhichcausedthecontroltotrip.

√ Verify the gas line has been purged and all connections

are adequately sealed. To check for gas leakage, see

Leak Check section on page 11.

√ Verify the indoor blower is properly set for the installation.

√ Verify the outdoor fan turns freely.

√ Verify the power supply branch circuit overcurrent

protection is properly sized.

√ Verify all exterior panels have been reinstalled and

securely fastened.

√ Verify the thermostat is wired correctly and preset for

initial operation. Set the thermostat system switch to

OFF and the fan switch to AUTO.

4. Verify that the compressor and outdoor fan motor are

not energized.

5. Run the unit and after approximately ﬁve minutes, set

the thermostat below room temperature. Verify the

shutdownsequence(seeOperatingSequence).

Verifying&AdjustingTemperatureRise

Verify the temperature rise through the unit is within the

range speciﬁed on the unit data label. Temperature rises

outside the speciﬁed range could result in premature heat

exchanger failure.

1. Place thermometers in the return and supply air stream

as close to the unit as possible. The thermometer on the

supply air side must be shielded against direct radiation

from the heat exchanger to avoid false readings.

2. Adjust all registers and duct dampers to the desired

position. Run the unit for 10 to 15 minutes before

taking any temperature readings. The temperature

rise is the difference between the supply and return air

temperatures.

NOTE: For typical duct systems, the temperature rise will

fallwithintherangespeciedonthedatalabel(withthe

blowerspeedatthefactoryrecommendedsetting)shown

in Table 16, page 40. If the measured temperature rise falls

outside the speciﬁed range, it may be necessary to change

the blower speed. Lowering the blower speed increases

the temperature rise and a higher speed decreases the

temperature rise.

The unit is equipped with a belt driven blower and variable

pitch motor sheave. The selection of a sheave setting

should be based on the desired CFM and the duct system

parameters.RefertotheACCA’sManualQforacomplete

description of how to determine these parameters and

Manual N for determination of the commercial load

requirements. The blower performance data can be found

inTables5-12(pages29-36).

The integrated control is designed to start the circulating air

blower 40 seconds after the gas valve opens and turn the

blower motor off 150 seconds after the gas valve is closed.

VerifyingBurnerOperation

WARNING:

Uninsulatedlivecomponentsareexposedwhen

thelouveredcontrolaccesspanelisremoved.

1. Remove the louvered control access panel to ensure

there is power to the unit.

2. Set the thermostat above room temperature and observe

the ignition sequence. The burner ﬂame should carry

over immediately between all burners and should extend

from each burner without lifting off, curling, or ﬂoating.

The ﬂames should be blue, without yellow tips.

3. After verifying ﬂame characteristics, set the thermostat

below room temperature and verify that the burner ﬂame

extinguishes completely.

VerifyingOperationofOver-Temperature

Limit Control

To verify operation of the over-temperature limit control,

make sure the louvered control access panel is in place

and that there is power to the unit.

1. Block the return airﬂow to the unit by installing a close-

off plate in place of or upstream of the ﬁlter.

2. Set the thermostat above room temperature and verify

the unit operates with the correct sequence of operation

(seeOperatingSequence).

NOTE: The over-temperature limit control should function

to turn off the gas valve within approximately four minutes

(exacttimedependsontheefciencyoftheclose-offwhen

blockingthereturnair).Thecirculatingairandcombustion

blowers should continue to run when the over-temperature

limit control switch opens.

3. Remove the close-off plate immediately after the over-

temperature limit control opens. If the unit operates

for more than four minutes with no return air, set the

thermostat below room temperature, shut off power to

the unit, and replace the over-temperature limit control.

Verifying&AdjustingFiringRate

The ﬁring rate must be veriﬁed for each installation to

prevent over-ﬁring of the unit.

CAUTION:

Donotre-drilltheburnerorices.Iftheorice

sizemustbechanged,useonlyneworices.

IMPORTANTNOTE:Theringratemustnotexceed

therate shownon the unit data label.Ataltitudes

above2,000ft.,itmustnotexceedthatonthedata

labelless4%foreach1,000ft.

Followthestepsbelowtodeterminetheunitringrate:

• Forinstallationsat2,000feetandless,theringrate

is the same as shown on the unit rating label.

• Forinstallationsabove2,000feet,computethering

rate as shown in the installation example on page 12.

1. Obtain the gas heating value from the gas supplier

(HHV).

2. Shut off all other gas ﬁred appliances.

3. Start the unit in heating mode and allow it to run for at

least three minutes.

4.Measure the time (in seconds) required for the gas

meter to complete one revolution.

5. Convert the time per revolution to cubic feet of gas per

hourusingTable17(page41).

6. Multiply the gas ﬂow rate in cubic feet per hour by the

heating value of the gas in Btu per cubic foot to obtain

theringrateinBtuperhour.SeeExample(page17):

7. Adjustments to the ﬁring rate can be made by adjusting

the gas manifold pressure. See the High Altitude Deration

section(pages11&12)foradditionalinformationof

ﬁring rate at elevations above 2000 ft.

Manifold Pressure Adjustment

The manifold pressure must be set to the appropriate

valueforyourinstallation.Toadjustthemanifoldpressure:

1. Obtain the required manifold pressure setting from

Table15(page40).NOTE: The values listed in the table

is based on sea level values. At higher altitudes, the

heating value of gas is lower than the sea level heating

value.

2. Remove the regulator cap. Turn the high fire

adjusting screw clockwise to increase the pressure or

counterclockwise to reduce the pressure.

3. Replace the regulator cap after adjustments are

complete.

RefrigerantCharging

WARNING:

Ifrepairsmakeitnecessaryforevacuationand

charging,itshouldonlybedonebyqualied,

trainedpersonnelthoroughlyfamiliarwiththis

equipment.Somelocalcodesrequirelicensed

installation/service personnel to service this

type of equipment. Under no circumstances

should the owner attempt to install and/or

servicethisequipment.

Failuretocomplywiththiswarningcouldresult

inpropertydamage,personalinjury,ordeath.

The R6 Series packaged gas/electric units are fully charged

at the factory and when installed accordingly, no charging

is required. The refrigerant charge can be checked and

adjusted through the service ports provided on the units.

Use only gauge lines which have a “Schrader” depression

device present to actuate the valve. Refer to Figures 17

-19(pages42-43)

Refrigerant charging must be done by qualiﬁed personnel

familiar with safe and environmentally responsible

refrigerant handling procedures. See Unit Rating Plate

for the proper type and amount of refrigerant.

Example:

• Timefor1revolutionofagasmeterwitha1

cubicfootdial=40seconds.

• FromTable17read90cubicfeetgasperhour.

• Localheatingvalueofthegas(obtainedfrom

gassupplier)=1,040Btupercubicfoot.

• Inputrate=1,040x90=93,600Btuh.

OPERATING SEQUENCE

The operating sequences for the heating, cooling, and fan

modes are described below. Refer to the wiring diagrams

(Figures15&16,pages38&39).

Cooling Mode

1. On a call for cooling the thermostat closes, applying 24

VAC to Y1, G, & Y2 if Stage 2 cooling is calling.

2. G applies 24VAC to the main circulating blower circuit.

3. Y1 & Y2 apply 24VAC through all safety switches before

energizing their respective contactors.

4. When the thermostat is satisﬁed the contactors are

de-energized.

5. The circulating blower motor de-energizes immediately.

Heating Mode

1. On a call for heat, the thermostat closes, applying 24

VAC to the W1terminal(andW2 terminal if Stage 2

heatisrequired).

2. The integrated control monitors the safety circuit at all

times. If either the roll-out switch or the over-temperature

limit controls open, the gas valve will not energize.

The main blower continues to operate until the over-

temperature limits close, the ﬂame roll-out switch is

manually reset, or the thermostat is satisﬁed.

3. The integrated control checks all safety switches at

the beginning of each heating cycle. If closed, the

combustion blower performs a 10 second pre-purge.

4. The integrated control will then supply power to the

direct spark ignitor and immediately energizes the gas

valve.

NOTE: Burner operation begins in high ﬁre mode

with both Stage 1 and Stage 2 gas valve energized,

independent of the thermostat call for Stage 2 heat. If

after 30 seconds of operation with no call for Stage 2

heat, the integrated control will resume heating operation

in low ﬁre mode of operation and Stage 2 gas valve is

de-energized.

5. The ﬂame must be proven through the ﬂame sensor in

10 seconds to hold the gas valve open. The integrated

control will monitor the gas ﬂame with the ﬂame sensor

for the entire time the gas valve is open. If for any reason

the gas ﬂame drops out, the gas valve will immediately

close. After 30 second purge, the integrated control will

try to ignite fourteen more times.

6. The main air blower will start and continue to run 40

seconds after the gas valve opens.

7. When the thermostat is satisﬁed, the integrated control is

de-energized. The gas valve and combustion blower de-

energize immediately while the main air blower continues

to run through the blower off delay of approximately 150

seconds.

8. If the unit fails to prove ﬂame after ﬁfteen ignition

attempts, it will go into a soft lockout. The unit will re-

attempt the start-up procedure every hour until the

thermostat is satisﬁed or 24 VAC power is removed

from the unit for a minimum period of 5 seconds. NOTE:

SeeTroubleshootingsection(page21)foracomplete

list of heating operation fault codes.

BlowerMode

1. On a call for fan operation, the thermostat applies 24

VAC directly to the blower contactor.

2. The circulating blower is energized immediately.

UNIT MAINTENANCE

ELECTRICAL SHOCK, FIRE OR EXPLOSION

HAZARD

Failuretofollowsafetywarningsexactlycould

resultinseriousinjuryorpropertydamage.

Improper servicing could result in dangerous

operation, serious injury, death or property

damage.

• Before servicing, disconnect all electrical

powertofurnace.

• Whenservicingcontrols,labelallwiresprior

todisconnecting.Reconnectwirescorrectly.

• Verifyproperoperationafterservicing.”

WARNING:

RISQUEDECHOCÉLECTRIQUE,D’INCENDIE

OUD’EXPLOSION

Le non-respect des avertissements de sécurité

pourrait entraîner

unfonctionnementdangereux

del’appareil,

desblessuresgraves,lamortou

des dommages matériels.

Un entretein incorrect pourrait entraîner un

fonctionnementdangereuxdel’appareil,des

blessuresgraves,lamortoudesdommages

matériels

• Couper toute alimentation électrique au

générateurd’airchaudavantdeprodéder

auxtravauxd’entretein.

• Aumomentdel’entretiendescommandes,

étiqueteztousleslsavantdelesdébrancher.

S’assurerdelesraccordercorrectement.

•S’assurer que l’appareil fonctionne

adéquatementaprésl’entretien.

AVERTISSEMENT:

NOTE: These maintenance instructions are primarily

intended to assist qualiﬁed technicians experienced in

the proper maintenance and operation of this appliance.

To achieve optimum performance from the air conditioner

and minimize equipment failure, it is recommended that

periodic maintenance be performed on this unit. The

ability to properly perform maintenance on this equipment

requires certain mechanical skills and tools. Please consult

your dealer for maintenance information and availability

of maintenance contracts.

Routine Maintenance

Please consult your dealer for maintenance information

and availability of maintenance contracts.At a minimum,

routinemaintenanceshouldincludethefollowingitems:

CAUTION:

Usecarewhenremovingpartsfromthisunit.

Personal injury can result from sharp metal

edgespresentinallequipmentofsheetmetal

construction.

Air Filters

WARNING:

Neveroperatetheunitwithoutltersinplace.

Dust and lint in the return air can build up

on internal components, resulting in loss of

efciency,equipmentdamage,andpossiblere.

It is recommended that the air ﬁlters be inspected and

cleaned or replaced every three to four weeks using ﬁlters

of likesizeandkind.Table1 (page 8) lists the factory

installed ﬁlter sizes and quantities for each unit.

IMPORTANTNOTE:R6GPunitsareequippedwith2”

pleateddisposablelters.Filterrackisadjustablefor

1”permanenttypelters.DONOTuse1”disposable

lters.

Blower Compartment

Build up of dirt and lint on the blower and motor can create

excessive loads on the motor resulting in higher than

normal operating temperatures and possible shortened

service life. It is recommended that the blower compartment

be cleaned monthly during heating and cooling seasons

to remove any dirt and lint that may have accumulated in

the compartment or on the blower and motor. Inspect the

blower drive belt for cracks, excessive wear and proper

tension after cleaning the compartment.

Condensate Drain & Outdoor Coil

Inspect the condensate drain and outdoor coil at the

beginning of each cooling season. Remove any debris.

Cleantheoutdoorcoilandhailguardlouvers(optional)

as necessary using a mild detergent and water. Rinse

thoroughly with water.

Electrical

WARNING:

Thisunit mayhavemore than oneelectrical

supply.Toavoidriskofelectricalshock,personal

injury,ordeath,disconnectallelectricalpower

totheunitbeforeperforminganymaintenance

or service.

CAUTION:

Label all wires prior to disconnection when

servicing controls. Wiring errors can cause

improper and dangerous operation.

Inspect the electrical connections for tightness at the

beginning of each heating and cooling season. Service

as necessary.

Motor / Bearing Lubrication

WARNING:

Lubrication of the motors in this unit is not

required. Do not lubricate any motor in this

product.

• Theblowerassemblyinthisunitisequippedwithtwo

support bearings. The support bearings are sealed

cartridge units and require no further lubrication.

• Theindoorblowermotorispre-lubricatedatthefactory

and does not require additional lubrication.

• Thecombustionairblowermotorandoutdoorfanmotors

are equipped with pre-lubricated sealed ball bearings.

Nofurtheroilingisrequiredforthelifeofthisproduct

Heat Exchanger & Burner Maintenance

WARNING:

Holesintheheatexchangercancauseproducts

ofcombustiontoenterthestructure.Replace

theheatexchangerifleaksarefound.Failure

topreventproductsofcombustionfrombeing

circulatedintotheoccupiedspacecancreate

potentially hazardous conditions including

carbonmonoxidepoisoningthatcouldresult

inpersonalinjuryordeath.

The unit should operate for many years without excessive

scale buildup in the heat exchanger, however, the heat

exchanger, the vent system, and the burners should be

inspectedandcleaned(ifrequired)byaqualiedtechnician

annually to ensure continued safe operation. Particular

attention must be given to identify deterioration from

corrosion or other sources.

Vent Cover Assembly

Inspect and clean the screen of the vent cover assembly

at the beginning of each heating and cooling seasons.

Cleaning of Burners

It is recommended that the burners be inspected and

cleanedperiodically(ifrequired)byaqualiedtechnician

annually to ensure continued safe operation. Particular

attention must be given to identify deterioration from

corrosion or other sources. If the burners must be cleaned,

follow the steps below.

1. Shut off the gas supply to the unit either at the meter

or at a manual valve in the supply piping.

2. Turn off all power to the unit and set the thermostat to

the lowest temperature setting.

3. Remove the louvered access panel from the unit.

4. Turn the gas control knob to the “OFF” position.

CAUTION:

Label all wires prior to disconnection when

servicing controls. Wiring errors can cause

improper and dangerous operation.

5. Disconnect the wires from the gas valve, ignitor, and

ﬂame sensor.

6. Using two wrenches, separate the ground-joint union

in the gas supply piping at the unit.

7. Remove the piping between the gas valve and the

ground-jointunion(ifnecessary).

8. Remove four screws securing the burner assembly to

the unit.

9. Carefully remove the burner assembly from the unit.

DO NOT DAMAGE THE IGNITOR WHILE REMOVING

THE BURNER ASSEMBLY.

10. Inspect the burners for accumulated dust or debris.

If necessary, carefully clean them with a soft wire

brush and/or the nozzle of a vacuum cleaner. DO

NOT DAMAGE THE IGNITOR OR FLAME SENSOR

WHILE CLEANING THE BURNER.

11. Replace all the parts in reverse order from which they

were removed.

12. Follow the lighting instructions found on the right

side door to return the unit to operation. Verify proper

operation after servicing.

CleaningofHeatExchanger

If the heat exchanger must be cleaned due to soot or

scale build up, follow the steps below.

1. Shut off the gas supply to the unit either at the meter

or at the manual valve in the gas supply piping.

2. Turn off all power to the unit and set the thermostat to

the lowest temperature setting.

WARNING:

Label all wires prior to disconnection when

servicing controls. Wiring errors can cause

improper and dangerous operation.

3. Disconnect the wires from the gas valve, ignitor, and

ﬂame sensor.

4. Using two wrenches, separate the ground-joint union

in the gas supply piping at the unit.

5. Remove the piping between the gas valve and the

ground-joint union, if necessary.

6. Remove the four screws securing the burner assembly

to the unit.

7. Carefully remove the burner assembly from the unit. DO

NOT DAMAGE THE IGNITOR OR FLAME SENSOR

WHILE REMOVING THE BURNER ASSEMBLY.

8. Remove three nuts securing the combustion blower to

the collector pan.

9. Remove the complete combustion blower from the unit.

10. Remove the screws securing the collector box cover

to the unit and remove cover plate.

11. Remove the screws securing the balance plate to the

collector box and the balance plate.

12. Remove the turbulator from each heat exchanger tube.

13. Attach a round wire brush to a length of high grade

stainless steel cable, such as drain cleanout cable.

Attach the other end of the spring cable to a variable

speed reversible drill. Slowly insert and rotate the cable

into the top portion of the heat exchanger. Operate the

drill alternating between forward and reverse, working

the cable in and out several times to obtain sufﬁcient

cleaning. Repeat this sequence for each heat exchanger

tube.

14. Remove all loosened debris from the heat exchanger

tubes using a vacuum cleaner.

15. Using a light, check the condition of the upper and

lower sections of the heat exchanger tube.

16. Inspect the burners and if necessary, clean them

carefully with a soft wire brush and/or the nozzle of a

vacuum cleaner. DO NOT DAMAGE THE IGNITOR OR

FLAME SENSOR WHILE CLEANING THE BURNER.

17. Replace all the parts in reverse order from which they

were removed. NOTE: If screws or other hardware are

corroded, replace only with corrosion resistant stainless

steel hardware of similar design.

18. Follow the operating instructions found on the right

side door and the User’s Information Manual to return

the unit to operation.

High Pressure Switch - This factory installed switch

is designed to de-energize the unit when excessive

pressure occurs due to abnormal conditions. Under normal

conditions, the switch is closed. If the discharge pressure

rises above 650 psig, then the switch will open and de-

energize the outdoor unit. The switch is a manually reset

type and will remain open until the button on top of the

switch is depressed.

IndoorCoilFreezeProtectionThermostats - The freeze

protection switches are designed to protect the indoor

coils from ice and frost accumulations in the event of a

loss of airﬂow by preventing the liquid refrigerant from

reaching the compressors. During normal operation, the

switches are closed and will open if the coil temperature

reaches28°F(-2°C).Theswitcheswillcloseifthecoil

temperaturereaches57°F(12°C).

LowPressureSwitch - This factory installed switch is

designed to protect the compressor from a loss of charge.

Under normal conditions, the switch is closed. If the suction

pressure falls below 5 psig, then the switch will open and

de-energize the outdoor unit. The switch will close again

once the suction pressure increases above 20 psig.

Over-Temperature Limit Control - The over-temperature

limit control acts to prevent the air temperature leaving the

unit from exceeding the maximum outlet air temperature.

If the limit opens, the blower limit relay will energize. The

circulating air blower and combustion blower will continue

to operate if the over-temperature limit control opens.

The descriptions below are various functional components

that affect the operation and shutting down of this unit.

Some of these components and their locations are shown

inFigure11(page21).

If any component on this unit must

be replaced, use only factory authorized replacement parts

speciﬁed in the Replacement Parts List provided online.

CentrifugalSwitch - The centrifugal switch acts to verify

that the inducer motor is running. Combustion gases are

drawn through the heat exchanger tubes and vented

through the vent system.

Flame Roll-Out Control - The ﬂame roll-out control acts

to verify that the burner ﬂame is being drawn into the heat

exchanger tubes. If the burner ﬂame is not being drawn

into the heat exchanger tubes, the roll-out control will

open within several seconds. The combustion blower will

continue to operate if the ﬂame roll-out control opens until

it is manually reset.

Flame Sensor - The ﬂame sensor acts to prove that ﬂame

has carried over from the ignitor to the right-most burner. If

no ﬂame is sensed, the unit will be shut down automatically

and attempt two additional ignition trials before going into

lockout. Recovery from lockout requires a manual reset

by either resetting the thermostat or removing 24 volts

for a period of 5 seconds. If the thermostat is still calling

for heat after one hour the control will automatically reset

and attempt to ignite the burner again.

Gas Valve - The gas valve controls the ﬂow of gas to

the burners in both low and high ﬁre. When the valve is

energized, it automatically opens and regulates the gas

pressure to the manifold.

COMPONENT FUNCTIONS

La page charge ...

Unbranded R6GP Guide d'installation

Marque: Unbranded

Modèle: R6GP

Taper: Guide d'installation

Ce manuel convient également à

R6GP 6, 7.5 - 10 Ton Archived 2/23/12

Télécharger le PDF

rapport

dans d''autres langues

English: Unbranded R6GP Installation guide

Unbranded R6GP Guide d'installation

Ce manuel convient également à

Unbranded R6GP Guide d'installation

dans d''autres langues

Documents connexes

Autres documents