Jenn-Air Pro-Style JDS8860BDP Installation Instructions Manual

Marque: Jenn-Air

Modèle: Pro-Style JDS8860BDP

Taper: Installation Instructions Manual

Ce manuel convient également à

INSTALLATION INSTRUCTIONS

30" (76.2 CM) SLIDE-IN DUAL FUEL RANGES

INSTRUCTIONS POUR L’INSTALLATION DES CUISINIÈRES

À BI-COMBUSTIBLE ENCASTRABLES DE 30" (76,2 CM)

Table of Contents Table des matières

RANGE SAFETY...................................................... 2

INSTALLATION REQUIREMENTS......................... 3

Tools and Parts..................................................... 3

Location Requirements......................................... 3

Electrical Requirements - U.S.A. Only.................. 5

Electrical Requirements - Canada Only ............... 6

Gas Supply Requirements.................................... 7

Countertop Preparation........................................ 8

INSTALLATION INSTRUCTIONS........................... 8

Unpack Range ...................................................... 8

Adjust Leveling Legs............................................. 8

Install Anti-Tip Bracket ......................................... 9

Electrical Connection - U.S.A. Only ..................... 9

Make Gas Connection........................................ 11

Verify Anti-Tip Bracket Is

Installed and Engaged........................................ 12

Level Range ........................................................ 13

Electronic Ignition System.................................. 13

Complete Installation.......................................... 13

GAS CONVERSIONS ............................................ 14

LP Gas Conversion............................................. 14

Natural Gas Conversion...................................... 16

SÉCURITÉ DE LA CUISINIÈRE ............................ 18

EXIGENCES D’INSTALLATION ............................ 19

Outillage et pièces............................................... 19

Exigences d'emplacement.................................. 19

Spécifications électriques –

Canada uniquement ............................................ 21

Spécifications de l'alimentation en gaz............... 22

Préparation du plan de travail ............................. 23

INSTRUCTIONS D’INSTALLATION...................... 23

Déballage de la cuisinière.................................... 23

Réglage des pieds de nivellement ...................... 24

Installation de la bride antibasculement.............. 24

Raccordement au gaz ......................................... 25

Vérifier que la bride antibasculement

est bien installée et engagée............................... 25

Réglage de l'aplomb de la cuisinière .................. 26

Système d'allumage électronique....................... 26

Achever l'installation............................................ 27

CONVERSIONS POUR CHANGEMENT

DE GAZ................................................................... 28

Conversion pour l'alimentation au propane........ 28

Conversion pour l'alimentation au gaz naturel.... 30

W10430953A

IMPORTANT:

Installer: Leave installation instructions with the homeowner.

Homeowner: Keep installation instructions for future reference.

IMPORTANT :

Installateur : Remettre les instructions d'installation au propriétaire.

Propriétaire : Conserver les instructions d'installation pour référence ultérieure.

RANGE SAFETY

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

WARNING: If the information in this manual is not followed exactly, a fire or explosion

may result causing property damage, personal injury or death.

– Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this

or any other appliance.

– WHAT TO DO IF YOU SMELL GAS:

•

Do not try to light any appliance.

•

Do not touch any electrical switch.

•

Do not use any phone in your building.

•

Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

•

If you cannot reach your gas supplier, call the fire department.

– Installation and service must be performed by a qualified installer, service agency or

the gas supplier.

WARNING: Gas leaks cannot always be detected by smell.

Gas suppliers recommend that you use a gas detector approved by UL or CSA.

For more information, contact your gas supplier.

If a gas leak is detected, follow the “What to do if you smell gas” instructions.

In the State of Massachusetts, the following installation instructions apply:

■ Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by

the State of Massachusetts.

■ If using a ball valve, it shall be a T-handle type.

■ A flexible gas connector, when used, must not exceed 3 feet.

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools needed

Parts supplied

Check that all parts are included.

■ LP/Natural Gas Conversion Kit (taped on regulator support at

back of range)

■ 5 - Burner caps

■ 2 - Burner grates

■ 3 - Oven racks

■ 2 - #12 x 1⁵⁄₈" screws (for mounting anti-tip bracket)

■ 1 - Metal ground strap (for 3-wire connection)

■ Anti-tip bracket (taped to package containing literature)

Anti-tip bracket must be securely mounted to the back wall or

floor. Thickness of flooring may require longer screws to

anchor bracket to subfloor. Longer screws are available from

your local hardware store.

Parts needed

Check local codes and consult gas supplier. Check existing gas

supply and electrical supply. See “Electrical Requirements” and

“Gas Supply Requirements” sections.

Location Requirements

IMPORTANT: Observe all governing codes and ordinances. Do

not obstruct flow of combustion and ventilation air.

■ It is the installer’s responsibility to comply with installation

clearances specified on the model/serial rating plate. The

model/serial rating plate is located behind the storage drawer

on the right-hand side of the oven frame.

■ The range should be located for convenient use in the

kitchen.

■ Recessed installations must provide complete enclosure of

the sides and rear of the range.

■ To eliminate the risk of burns or fire by reaching over heated

surface units, cabinet storage space located above the

surface units should be avoided. If cabinet storage is to be

provided, the risk can be reduced by installing a range hood

or microwave hood combination that projects horizontally a

minimum of 5" (12.7 cm) beyond the bottom of the cabinets.

■ All openings in the wall or floor where range is to be installed

must be sealed.

■ Cabinet opening dimensions that are shown must be used.

Given dimensions are minimum clearances.

■ The anti-tip bracket must be installed. To install the anti-tip

bracket shipped with the range, see “Install Anti-Tip Bracket”

section.

■ Grounded electrical supply is required. See “Electrical

Requirements” section.

■ Proper gas supply connection must be available. See “Gas

Supply Requirements” section.

■ Contact a qualified floor covering installer to check that the

floor covering can withstand at least 200°F (93°C).

■ Use an insulated pad or ¼" (0.64 cm) plywood under range if

installing range over carpeting.

Tip Over Hazard

A child or adult can tip the range and be killed.

Install anti-tip bracket to floor or wall per installation instructions.

Slide range back so rear range foot is engaged in the slot of the anti-tip bracket.

Re-engage anti-tip bracket if range is moved.

Do not operate range without anti-tip bracket installed and engaged.

Failure to follow these instructions can result in death or serious burns to children and adults.

To verify the anti-tip bracket is installed and engaged:

• Slide range forward.

• Look for the anti-tip bracket securely attached to floor or wall.

• Slide range back so rear range foot is under anti-tip bracket.

• See installation instructions for details.

WARNING

Anti-Tip

Bracket

Range Foot

■ Tape measure

■ Phillips screwdriver

■ Flat-blade screwdriver

■ ¹⁄₈" flat-blade screwdriver

■ Level

■ Hand or electric drill

■ Wrench or pliers

■ Pipe wrench

■ ¹⁵⁄₁₆" combination wrench

■ ¹⁄₈" (3.2 mm) drill bit (for

wood floors)

■ Marker or pencil

■ Pipe-joint compound

resistant to LP gas

■ ³⁄₁₆" (4.8 mm) carbide-tipped

masonry drill bit (for

concrete/ceramic floors)

■ Noncorrosive leak-detection

solution

For LP/Natural Gas

Conversions

■ ½" combination wrench

■ ¼" (6 mm) nut driver

■ ⁹⁄₃₂" (7 mm) nut driver

■ Masking tape

IMPORTANT: To avoid damage to your cabinets, check with your

builder or cabinet supplier to make sure that the materials used

will not discolor, delaminate or sustain other damage. This oven

has been designed in accordance with the requirements of UL

and CSA International and complies with the maximum allowable

wood cabinet temperatures of 194°F (90°C).

Mobile Home - Additional Installation Requirements

The installation of this range must conform to the Manufactured

Home Construction and Safety Standard, Title 24 CFR, Part 3280

(formerly the Federal Standard for Mobile Home Construction

and Safety, Title 24, HUD Part 280). When such standard is not

applicable, use the Standard for Manufactured Home

Installations, ANSI A225.1/NFPA 501A or with local codes.

In Canada, the installation of this range must conform with the

current standards CAN/CSA-A240-latest edition, or with local

codes.

Mobile home installations require:

■ When this range is installed in a mobile home, it must be

secured to the floor during transit. Any method of securing

the range is adequate as long as it conforms to the standards

listed above.

Product Dimensions

Model JDS8850

Model JDS8860

NOTE: Cooktop shown may differ from your model.

*Range can be raised approximately 1" (2.5 cm) by adjusting

the leveling legs.

**When installed in a 24" (61.0 cm) base cabinet with

25" (63.5 cm) countertop; front of oven door protrudes

5" (12.7 cm) beyond 24" (61.0 cm) base cabinet.

A. 30³⁄₄" (78.1 cm)

B. 35³⁄₄" (90.8 cm) height to underside

of cooktop edge with leveling legs

screwed all the way in*

C. Model/serial number plate (located

behind the storage drawer on the

right-hand side of the oven frame)

D. 29⁷⁄₈" (75.9 cm)

E. Gas information plate

(located behind the

warming drawer on the

left-hand side of oven

frame)

F. 29" (73.4 cm) from handle

to back of range**

G. 23" (58.4 cm) countertop

notch to rear of cooktop

⁷⁄₈" (78.4 cm)

B. 35³⁄₄" (90.8 cm) height to

underside of cooktop edge

with leveling legs screwed all

the way in*

C. Model/serial number plate

(located behind the storage

drawer on the right-hand side

of the oven frame)

D. 29⁷⁄₈" (75.9 cm)

E. Gas information plate (located

behind the storage drawer on

the left-hand side of the oven

frame)

F. 29" (73.7 cm) from handle to

back of range**

G. 27" (68.6 cm) from handle to

rear of cooktop

Cabinet Dimensions

Cabinet opening dimensions shown are for 25" (64.0 cm)

countertop depth, 24" (61.0 cm) base cabinet depth and

36" (91.4 cm) countertop height.

IMPORTANT: If installing a range hood or microwave hood

combination above the range, follow the range hood or

microwave hood combination installation instructions for

dimensional clearances above the cooktop surface.

Range may be installed with zero clearance to combustible

construction at the rear and on the sides below the cooktop.

NOTE: 24" (61.0 cm) minimum when bottom of wood or metal

cabinet is shielded by not less than ¹⁄₄" (0.64 cm) flame retardant

millboard covered with not less than No. 28 MSG sheet steel,

0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm) aluminum or

0.020" (0.5 mm) copper.

30" (76.2 cm) minimum clearance between the top of the cooking

platform and the bottom of an uncovered wood or metal cabinet.

Electrical Requirements - U.S.A. Only

The electrical connection to this range is designed only for use

with a flexible power cord. All ranges are shipped with a specially

designed 4-wire power supply cord. This cord should be used on

all new branch circuits, mobile homes and when local codes

prohibit grounding though the neutral. For a 3-wire power supply

cord replacement, service kit Part Number 74011285 must be

used.

If codes permit and a separate ground wire is used, it is

recommended that a qualified electrical installer determine that

the ground path and wire gauge are in accordance with local

codes.

Do not use an extension cord.

Be sure that the electrical connection and wire size are adequate

and in conformance with the National Electrical Code, ANSI/

NFPA 70-latest edition and all local codes and ordinances.

A copy of the above code standards can be obtained from:

National Fire Protection Association

1 Batterymarch Park

Quincy, MA 02169-7471

WARNING: Improper connection of the equipment-grounding

conductor can result in a risk of electric shock. Check with a

qualified electrician or service technician if you are in doubt as to

whether the appliance is properly grounded. Do not modify the

power supply cord plug. If it will not fit the outlet, have a proper

outlet installed by a qualified electrician.

Electrical Connection

To properly install your range, you must determine the type of

electrical connection you will be using and follow the instructions

provided for it here.

■ Range must be connected to the proper electrical voltage

and frequency as specified on the model/serial number rating

plate. The model/serial rating plate is located behind the

storage or warming drawer on the right-hand side of the oven

frame or on the right-hand side of the bottom oven frame,

depending on your model. Refer to the figures in the “Product

Dimensions” section of the “Location Requirements” section.

■ This range is manufactured with a 4-wire 40-amp power cord.

For a 3-wire connection order UL listed power cord Part

Number 74011285.

*The NEC calculated load is less than the total connected load

listed on the model/serial rating plate.

**If connecting to a 50-amp circuit, use a 50-amp rated cord with

kit. For 50-amp rated cord kits, use kits that specify use with a

nominal 1³⁄₈" (34.9 mm) diameter connection opening.

■ A circuit breaker is recommended.

■ Wire sizes and connections must conform with the rating of

the range.

■ The wiring diagram is located at the back of the warming

drawer.

A. 13" (33.0 cm) upper cabinet depth

B. 30" (76.2 cm) min. opening width

C. For minimum clearance to the top of the cooktop, see NOTE.

D. 23¹⁄₄" (59.1 cm) opening depth

E. 30" (76.2 cm) min. opening width

F. Electrical and gas supply - 5½" (14.0 cm) min. from either cabinet,

10" (25.4 cm) max. from floor. Nothing located in shaded area can

extend more than 2¼" (5.7 cm) from back wall or range will not slide

all the way back. Grounded outlet must be flush mounted.

G. Cabinet door or hinge should not extend into cutout.

H. 18" (45.7 cm)

I. 3" (7.6 cm) min. clearance from both sides of the range to the side

wall or other combustible material.

Range Rating* Specified Rating of

Power Supply Cord Kit

and Circuit Protection

120/240 Volts 120/208 Volts Amps

8.8 - 16.5 KW

16.6 - 22.5 KW

7.8 - 12.5 KW

12.6 - 18.5 KW

40 or 50**

If connecting to a 4-wire system:

The green ground wire of the 4-wire power supply cord must be

connected to the cabinet. See “Electrical Connection” section.

Grounding through the neutral conductor is prohibited for new

branch-circuit installations (1996 NEC); mobile homes; and

recreational vehicles, or an area where local codes prohibit

grounding through the neutral conductor.

When a 4-wire receptacle of NEMA Type 14-50R is used, a

matching UL listed, 4-wire, 250-volt, 40- or 50-amp, range power

supply cord (pigtail) must be used. This cord contains 4 copper

conductors with ring terminals or open-end spade terminals with

upturned ends, terminating in a NEMA Type 14-50P plug on the

supply end.

The fourth (grounding) conductor must be identified by a green or

green/yellow cover and the neutral conductor by a white cover.

Cord should be Type SRD or SRDT with a UL listed strain relief

and be at least 4 ft (1.22 m) long.

The minimum conductor sized for the copper 4-wire power

cord are:

40-amp circuit

2 No.-8 conductors

1 No.-10 white neutral

1 No.-8 green grounding

If connecting to a 3-wire system:

Local codes may permit the use of a UL listed, 3-wire, 250-volt,

40- or 50-amp range power supply cord (pigtail). Order UL listed

3-wire power cord Part Number 74011285. This cord contains 3

copper conductors with ring terminals or open-end spade

terminals with upturned ends, terminating in a NEMA Type 10-50P

plug on the supply end. Connectors on the appliance end must be

provided at the point the power supply cord enters the appliance.

This uses a 3-wire receptacle of NEMA Type 10-50R. For a 3-wire

power supply cord replacement, service kit Part Number

74011285 must be used.

Electrical Requirements - Canada Only

If codes permit and a separate ground wire is used, it is

recommended that a qualified electrical installer determine that

the ground path is adequate and wire gauge are in accordance

with local codes.

Be sure that the electrical connection and wire size are adequate

and in conformance with CSA Standard C22.1, Canadian

Electrical Code, Part 1 - latest edition, and all local codes and

ordinances.

A copy of the above code standards can be obtained from:

Canadian Standards Association

178 Rexdale Blvd.

Toronto, ON M9W 1R3 CANADA

■ Check with a qualified electrical installer if you are not sure

the range is properly grounded.

*The NEC calculated load is less than the total connected load

listed on the model/serial rating plate.

■ A time-delay fuse or circuit breaker is recommended.

■ This range is equipped with a CSA International Certified

Power Cord intended to be plugged into a standard 14-50R

wall receptacle. Be sure the wall receptacle is within reach of

range’s final location.

■ Do not use an extension cord.

4-wire receptacle (14-50R)

3-wire receptacle (10-50R)

Range Rating* Rating of

Power

Supply Cord

Circuit

Protection

120/240 Volts 120/208 Volts Amps Amps

8.8 - 16.5 KW

16.6 - 22.5 KW

7.8 - 12.5 KW

12.6 - 18.5 KW

40 or 50

WARNING

Electrical Shock Hazard

Electrically ground range.

Failure to do so can result in death, fire, or

electrical shock.

Gas Supply Requirements

Observe all governing codes and ordinances.

IMPORTANT: This installation must conform with all local codes

and ordinances. In the absence of local codes, installation must

conform with American National Standard, National Fuel Gas

Code ANSI Z223.1 - latest edition or CAN/CGA B149 - latest

edition.

IMPORTANT: Leak testing of the range must be conducted

according to the manufacturer’s instructions.

Type of Gas

Natural gas:

This range is design-certified by CSA International for use with

Natural gas or, after proper conversion, for use with LP gas.

■ This range is factory set for use with Natural gas. See “Gas

Conversions” section. The gas information plate (located

behind the warming or storage drawer on the side of the oven

frame or on the side of the bottom oven frame, depending on

your model) has information on the types of gas that can be

used. If the types of gas listed do not include the type of gas

available, check with the local gas supplier.

LP gas conversion:

Conversion must be done by a qualified service technician.

No attempt shall be made to convert the appliance from the gas

specified on the model/serial rating plate for use with a different

gas without consulting the serving gas supplier. See “Gas

Conversions” section.

Gas Supply Line

■ Provide a gas supply line of ¾" (1.9 cm) rigid pipe to the

range location. A smaller size pipe on longer runs may result

in insufficient gas supply. With LP gas, piping or tubing size

can be ½" (1.3 cm) minimum. Usually, LP gas suppliers

determine the size and materials used in the system.

NOTE: Pipe-joint compounds that resist the action of LP gas

must be used. Do not use TEFLON

®†

tape.

Flexible metal appliance connector:

■ If local codes permit, a new CSA design-certified,

4 to 5 ft (122 to 152.4 cm) long, ½" (1.3 cm) or

¾" (1.9 cm) I.D., flexible metal appliance connector may

be used for connecting range to the gas supply line.

■ A ½" (1.3 cm) male pipe thread is needed for connection

to the female pipe threads of the inlet to the appliance

pressure regulator.

■ Do not kink or damage the flexible metal tubing when

moving the range.

Rigid pipe connection:

The rigid pipe connection requires a combination of pipe

fittings to obtain an in-line connection to the range. The rigid

pipe must be level with the range connection. All strains must

be removed from the supply and fuel lines so range will be

level and in line.

■ Must include a shutoff valve:

The supply line must be equipped with a manual shutoff

valve. This valve should be located in the same room but

external to the range opening, such as an adjacent cabinet. It

should be in a location that allows ease of opening and

closing. Do not block access to shutoff valve. The valve is for

turning on or shutting off gas to the range.

Gas Pressure Regulator

The gas pressure regulator supplied with this range must be

used. The inlet pressure to the regulator should be as follows for

proper operation:

Natural gas:

Minimum pressure: 5" WCP

Maximum pressure: 14" WCP

LP gas:

Minimum pressure: 11" WCP

Maximum pressure: 14" WCP

Contact local gas supplier if you are not sure about the inlet

pressure.

WARNING

Explosion Hazard

Use a new CSA International approved gas supply line.

Install a shut-off valve.

Securely tighten all gas connections.

If connected to LP, have a qualified person make sure

gas pressure does not exceed 14" (36 cm) water

column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

†®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.

A. Gas supply line

B. Shutoff valve “open” position

C. To range

Burner Input Requirements

Input ratings shown on the model/serial rating plate are for

elevations up to 2,000 ft (609.6 m).

For elevations above 2,000 ft (609.6 m), ratings are reduced at a

rate of 4% for each 1,000 ft (304.8 m) above sea level (not

applicable for Canada).

Gas Supply Pressure Testing

Gas supply pressure for testing regulator must be at least

1" water column pressure above the manifold pressure shown on

the model/serial rating plate.

Line pressure testing above ½ psi gauge (14" WCP)

The range and its individual shutoff valve must be disconnected

from the gas supply piping system during any pressure testing of

that system at test pressures in excess of ½ psi (3.5 kPa).

Line pressure testing at ½ psi gauge (14" WCP) or lower

The range must be isolated from the gas supply piping system by

closing its individual manual shutoff valve during any pressure

testing of the gas supply piping system at test pressures equal to

or less than ½ psi (3.5 kPa).

Countertop Preparation

(for Slide-in Ranges Only)

The cooktop sides of the slide-in range fit over the cutout edge of

your countertop.

If you have a square finish (flat) countertop and the opening width

is 30" (76.2 cm), no countertop preparation is required.

Formed front-edged countertops must have molded edge

shaved flat ³⁄₈" (1.0 cm) from each front corner of opening.

Tile countertops may need trim cut back ³⁄₈" (1.0 cm) from each

front corner and/or rounded edge flattened.

If countertop opening width is greater than 30" (76.2 cm), adjust

the ³⁄₈" (1.0 cm) dimension.

Countertop must be level. Place level on countertop, first side to

side, then front to back. If countertop is not level, range will not

be level. Range must be level for satisfactory baking conditions.

INSTALLATION INSTRUCTIONS

Unpack Range

1. Remove shipping materials, tape and film from the range.

Keep cardboard bottom under range.

2. Remove oven racks and parts package from inside oven.

3. To remove cardboard bottom, place range on its back, take

4 cardboard corners from the carton. Stack one cardboard

corner on top of another. Repeat with the other 2 corners.

Place them lengthwise on the floor behind the range to

support the range when it is laid on its back.

4. Using 2 or more people, firmly grasp the range and gently lay

it on its back on the cardboard corners.

5. Pull cardboard bottom firmly to remove.

6. Use an adjustable wrench to loosen the leveling legs.

7. Place cardboard or hardboard in front of range. Using 2 or

more people, stand range back up onto cardboard or

hardboard.

Adjust Leveling Legs

1. If range height adjustment is necessary, use a wrench or

pliers to loosen the 4 leveling legs.

This may be done with the range on its back or with the range

supported on 2 legs after the range has been placed back to

a standing position.

NOTE: To place range back up into a standing position, put a

sheet of cardboard or hardboard in front of range. Using 2 or

more people, stand range back up onto the cardboard or

hardboard.

2. Adjust the leveling legs to the correct height. Leveling legs

can be loosened to add up to a maximum of 1" (2.5 cm). A

minimum of ³⁄₁₆" (5 mm) is needed to engage the anti-tip

bracket.

30"

(76.2 cm)

30 ¾"

(78.1 cm)

³⁄₈"

(1.0 cm)

WARNING

Excessive Weight Hazard

Use two or more people to move and install range.

Failure to do so can result in back or other injury.

WARNING

Tip Over Hazard

A child or adult can tip the range and be killed.

Install anti-tip bracket to floor or wall per installation

instructions.

Slide range back so rear range foot is engaged in the

slot of the anti-tip bracket.

Re-engage anti-tip bracket if range is moved.

Do not operate range without anti-tip bracket installed

and engaged.

Failure to follow these instructions can result in death

or serious burns to children and adults.

NOTE: If height adjustment is made when range is standing,

tilt the range back to adjust the front legs, then tilt forward to

adjust the rear legs.

3. When the range is at the correct height, check that there is

adequate clearance under the range for the anti-tip bracket.

Before sliding range into its final location, check that the anti-

tip bracket will slide under the range and onto the rear

leveling leg prior to anti-tip bracket installation.

Install Anti-Tip Bracket

1. Remove the anti-tip bracket that is taped to the package

containing literature.

2. Determine which mounting method to use: floor or wall.

If you have a stone or masonry floor, you can use the wall

mounting method.

3. Determine and mark centerline of the cutout space. The

mounting bracket can be installed on either the left side or

right side of the cutout. Position mounting bracket in cutout

so that right (or left) edge of the bracket is 14¹⁄₄" (36.2 cm)

from centerline, as shown.

4. Drill two ¹⁄₈" (3 mm) holes that correspond to the bracket

holes of the determined mounting method. See the following

illustrations.

5. Using the Phillips screwdriver, mount anti-tip bracket to the

wall or floor with the two #12 x 1⁵⁄₈" screws provided.

Electrical Connection - U.S.A. Only

Power Supply Cord (optional)

This range is shipped with a specially designed 4-wire power

supply cord. This cord should be used on all new branch circuits,

mobile homes and when local codes prohibit grounding though

the neutral. For a 3-wire power supply cord replacement, service

kit Part Number 74011285 must be used.

1. Disconnect power.

2. Use Phillips screwdriver to remove the terminal block cover

screw located on the back of the range. Pull cover down and

toward you to remove cover.

3. Add strain relief.

■ Assemble a UL listed strain relief in the opening.

■ Feed the power supply cord through the opening in the

cord/conduit plate on bottom of range. Allow enough

slack to easily attach the wiring to the terminal block.

A. Centerline

B. 14¹⁄₄" (36.2 cm)

Floor Mounting Wall Mounting

A. #12 x 1⁵⁄₈" screws

B. Anti-tip bracket

A. #12 x 1⁵⁄₈" screws

B. Anti-tip bracket

A. UL listed strain relief

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Use a new 40 amp power supply cord.

Plug into a grounded outlet.

Failure to follow these instructions can result in death,

fire, or electrical shock.

CORD

CONDUIT

■ Tighten strain relief screw against the power supply cord.

■ Feed the flexible conduit through the strain relief, allowing

enough slack to easily attach wiring to the terminal block.

■ Tighten strain relief screw against the flexible conduit.

Electrical Connection Options

4-wire connection: Power Supply Cord

Use this method for:

■ New branch-circuit installations (1996 NEC)

■ Mobile homes

■ Recreational vehicles

■ In an area where local codes prohibit grounding through the

neutral

1. Feed the power supply cord through the opening in the cord/

conduit plate on bottom of range. Allow enough slack to

easily attach the wiring to the terminal block.

2. Use Phillips screwdriver to connect the green ground wire

from the power supply cord to the range with the ground-link

screw. The ground wire must be attached first.

3. Use ³⁄₈" nut driver to connect the neutral (white) wire to the

center terminal block post with one of the 10-32 hex nuts.

4. Connect line 1 (black) and line 2 (red) wires to the outer

terminal block posts with 10-32 hex nuts.

5. Securely tighten hex nuts.

NOTE: For power supply cord replacement, only use a power

cord rated at 250 volts minimum, 40 amps or 50 amps that is

marked for use with nominal 1³⁄₈" (3.5 cm) diameter

connection opening, with ring terminals and marked for use

with ranges. For a 3-wire power supply cord replacement,

service kit Part Number 74011285 must be used.

6. Replace terminal block access cover.

If your home has: And you will be

connecting to:

Go to Section:

4-wire receptacle

(NEMA type 14-50R)

A UL listed,

250-volt

minimum,

40-amp, range

power supply

cord

4-wire connection:

Power supply cord

3-wire receptacle

(NEMA type 10-50R)

A UL listed,

250-volt

minimum,

40-amp, range

power supply

cord

3-wire connection:

Power supply cord

A. Terminal block

B. Ground-link screw

C. Cord/conduit plate

D. Power supply cord wires

A. 10-32 hex nut

B. Ground-link screw

C. Line 1 (black)

D. Green ground wire

E. Neutral (center) wire

F. Line 2 (red)

3-wire connection: Power Supply Cord (optional)

NOTE: For power supply cord replacement, only use a power

cord rated at 250 volts minimum, 40 amps or 50 amps that is

marked for use with nominal 1³⁄₈" (3.5 cm) diameter

connection opening, with ring terminals and marked for use

with ranges.

Use this method only if local codes permit connecting chassis

ground conductor to neutral wire of power supply cord.

1. Feed the power supply cord through the opening in the cord/

conduit plate on bottom of range. Allow enough slack to

easily attach the wiring to the terminal block.

2. Use ³⁄₈" nut driver to connect the neutral (white) wire and

copper ground strap provided to the center terminal block

post with one of the 10-32 hex nuts. The opposite end of the

copper ground strap should be secured to the oven back with

the green ground-link screw.

3. Connect line 1 (black) and line 2 (red) wires to the outer

terminal block posts with 10-32 hex nuts.

4. Securely tighten hex nuts.

5. Replace terminal block access cover.

Make Gas Connection

Typical flexible connection

1. Apply pipe-joint compound made for use with LP gas to the

smaller thread ends of the flexible connector adapters (see B

and G in the following illustration).

2. Attach one adapter to the gas pressure regulator and the

other adapter to the gas shutoff valve. Tighten both adapters.

3. Use a ¹⁵⁄₁₆" combination wrench and an adjustable wrench to

attach the flexible connector to the adapters. Check that

connector is not kinked.

A. Terminal block

B. Ground-link screw

C. Cord/conduit plate

D. Power supply cord wires

E. Metal ground strap

A. 10-32 hex nut

B. Line 1 (black)

C. Ground-link screw

D. Neutral (white) wire

E. Line 2 (red)

A. Gas pressure regulator

B. Use pipe-joint compound.

C. Adapter (must have ½" male

pipe thread)

D. Flexible connector

E. Manual gas shutoff valve

F. ½" or ¾" gas pipe

G. Use pipe-joint compound.

H. Adapter

WARNING

Explosion Hazard

Use a new CSA International approved gas supply line.

Install a shut-off valve.

Securely tighten all gas connections.

If connected to LP, have a qualified person make sure

gas pressure does not exceed 14" (36 cm) water

column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

4. Gas supply pipe must not be more than 10" (25.4 cm) above

the floor.

Complete Connection

1. Open the manual shutoff valve in the gas supply line. The

valve is open when the handle is parallel to the gas pipe.

2. Test all connections by brushing on an approved

noncorrosive leak-detection solution. If bubbles appear, a

leak is indicated. Correct any leak found.

3. Remove cooktop burner caps and grates from package

containing parts. Align recess in burner caps with pins in

burner base. Burner caps should be level when properly

positioned. If burner caps are not properly positioned,

surface burners will not light. Place burner grates over

burners and caps.

4. Plug into appropriate outlet. See “Electrical Requirements”

section.

5. Turn power on.

Verify Anti-Tip Bracket Is Installed and

Engaged

On models with a storage drawer:

1. Remove the storage drawer.

2. Use a flashlight to look underneath the bottom of the range.

3. Visually check that the rear range foot is inserted into the slot

of the anti-tip bracket.

On models with a warming drawer:

1. Place the outside of your foot against the bottom front of the

warming drawer to keep the range from moving, and grasp

the control panel with two hands as shown.

2. Slowly attempt to tilt the range forward.

If you encounter immediate resistance, the range foot is

engaged in the anti-tip bracket.

3. If the rear of the range lifts more than ½" (1.3 cm) off the floor

without resistance, stop tilting the range and lower it gently

back to the floor. The range foot is not engaged in the anti-tip

bracket.

IMPORTANT: If there is a snapping or popping sound when lifting

the range, the range may not be fully engaged in the bracket.

Check to see if there are obstructions keeping the range from

sliding to the wall or keeping the range foot from sliding into the

bracket. Verify that the bracket is held securely in place by the

mounting screws.

4. Slide the range forward, and verify that the anti-tip bracket is

securely attached to the floor or wall.

5. Slide range back so the rear range foot is inserted into the

slot of the anti-tip bracket.

IMPORTANT: If the back of the range is more than 2" (5.1 cm)

from the mounting wall, the rear range foot may not engage the

bracket. Slide the range forward and determine if there is an

obstruction between the range and the mounting wall. If you

need assistance or service, refer to the “Assistance or Service”

section of the Use and Care Guide, or the cover or “Warranty”

section of the User Instructions, for contact information.

6. Repeat steps 1 and 2 to ensure that the range foot is

engaged in the anti-tip bracket.

If the rear of the range lifts more than ½" (1.3 cm) off the floor

without resistance, the anti-tip bracket may not be installed

correctly. Do not operate the range without anti-tip bracket

installed and engaged. Please reference the “Assistance or

Service” section of the Use and Care Guide, or the cover or

“Warranty” section of the User Instructions, to contact

service.

A. Gas pressure regulator

B. Adapter

C. Flexible connector

D. Manual shutoff valve

E. 10" (25.4 cm) max. straight pipe

A. Closed valve

B. Open valve

Level Range

1. Place rack in oven.

2. Place level on rack and check levelness of range, first side to

side; then front to back.

3. If range is not level, pull range forward until rear leveling leg is

removed from the anti-tip bracket.

4. Use wrench to adjust leveling legs up or down until range is

level. Push range back into position.

5. Check that rear leveling leg is engaged in anti-tip bracket.

NOTE: Range must be level for satisfactory baking performance.

Electronic Ignition System

Initial lighting and gas flame adjustments

Cooktop and oven burners use pilotless igniters in place of

standing pilots. When the cooktop control knob is turned to the

“LITE” position, the system creates a spark to light the burner. This

sparking continues, as long as the control knob is turned to “LITE.”

When the oven control is turned to the desired setting, a glow bar

igniter heats and ignites the gas.

Check Operation of Cooktop Burners

Standard Surface Burners

Push in and turn each control knob to the “LITE” position.

The flame should light within 4 seconds. The first time a burner is

lit it may take longer than 4 seconds to light because of air in the

gas line.

If burners do not light properly:

■ Turn cooktop control knob to the “OFF” position.

■ Check that the range is plugged in and the circuit breaker has

not tripped or the household fuse has not blown.

■

Check that the gas shutoff valves are set to the “open” position.

■ Check that burner caps are properly positioned on burner

bases.

Repeat start-up. If a burner does not light at this point, turn the

control knobs to “Off” and contact your dealer or authorized

service company for assistance.

Adjust Flame Height

Adjust the height of top burner flames. The cooktop “low” burner

flame should be a steady blue flame approximately ¼" (0.64 cm)

high.

To adjust standard burners:

The flame can be adjusted using the adjustment screw in the

center of the valve stem. The valve stem is located directly

underneath the control knob.

If the “low” flame needs to be adjusted:

1. Light 1 burner and turn to lowest setting.

2. Remove the control knob.

Hold the knob stem in the low position using a pair of pliers. Use an

¹⁄₈

" (3.0 mm) flat-blade screwdriver to turn the screw located in the

center of the control knob stem until the flame is the proper size.

3. Replace the control knob.

4. Test the flame by turning the control from “LO” to “HI,”

checking the flame at each setting.

5. Repeat the above steps for each burner.

To adjust double burner:

1. Light burner and turn to lowest setting where both inner and

outer burners are lit.

2. Remove the control knob.

Insert an ¹⁄₈" (3.0 mm) flat-blade screwdriver into adjustment

locations shown in the following illustration and engage the

slotted screw. Turn the screw until the flame is the proper size.

3. Replace the control knob.

4. Test the flame by turning the control from “LO” to “HI,”

checking the flame at each setting.

Complete Installation

1. Check that all parts are now installed. If there is an extra part,

go back through the steps to see which step was skipped.

2. Check that you have all of your tools.

3. Dispose of/recycle all packaging materials.

4. Check that range level. See “Level Range.”

5. Use a mild solution of liquid household cleaner and warm

water to remove waxy residue caused by shipping material.

Dry thoroughly with a soft cloth. For more information, see

the “Range Care” section of the Use and Care Guide.

6. Read “Range Use” in the Use and Care Guide.

7. Turn on surface burners and oven. See the Use and Care

Guide for specific instruction on range operation.

A. Low flame

B. High flame

If range does not operate, check the following:

■ Household fuse is intact and tight, or circuit breaker has not

tripped.

■ Range is plugged into a grounded outlet.

■ Electrical supply is connected.

■ See “Troubleshooting” in the Use and Care Guide.

8. When the range has been on for 5 minutes, check for heat. If

the range is cold, turn off the range and check that the gas

supply line shutoff valve is open.

■ If the gas supply line shutoff valve is closed, open it, then

repeat the 5-minute test as outlined above.

■ If the gas supply line shutoff valve is open, close it, and

contact a qualified technician.

If you need Assistance or Service:

Please reference the “Assistance or Service” section of the

Use and Care Guide or contact the dealer from whom you

purchased your range.

GAS CONVERSIONS

Gas conversions from Natural gas to LP gas or from LP gas to

Natural gas must be done by a qualified installer.

LP Gas Conversion

1. Turn manual shutoff valve to the closed position.

2. Unplug range or disconnect power.

To Convert Gas Pressure Regulator

1. Locate gas pressure regulator at the back of the range.

IMPORTANT: Do not remove the gas pressure regulator.

WARNING

Explosion Hazard

Use a new CSA International approved gas supply line.

Install a shut-off valve.

Securely tighten all gas connections.

If connected to LP, have a qualified person make sure

gas pressure does not exceed 14" (36 cm) water

column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

A. To range

B. Shutoff valve (closed position)

C. Gas supply line

WARNING

Tip Over Hazard

A child or adult can tip the range and be killed.

Install anti-tip bracket to floor or wall per installation

instructions.

Slide range back so rear range foot is engaged in the

slot of the anti-tip bracket.

Re-engage anti-tip bracket if range is moved.

Do not operate range without anti-tip bracket installed

and engaged.

Failure to follow these instructions can result in death

or serious burns to children and adults.

2. Unscrew the regulator cap and remove the plastic cover.

3. Flip the regulator cap over and replace the plastic cover.

4. Screw the regulator cap securely back into place. Do not

overtighten.

To Convert Surface Burners

1. If installed, remove the burner grates.

2. Remove the burner caps.

3. Using a Phillips screwdriver, remove the burner base.

4. Apply masking tape to the end of a ⁹⁄₃₂" (7 mm) nut driver to

help hold the Natural gas orifice spud in the nut driver while

changing it. Press nut driver down onto the Natural gas orifice

spud and remove by turning it counterclockwise and lifting

out. Set Natural gas orifice spud aside.

Use the following chart for correct LP gas orifice spud for each

burner. Refer to the gas information plate on the lower left side of

the front frame for proper sizing of LP gas orifice spuds for each

burner location.

LP Gas Orifice Spud Chart for Models JDS8850 and JDS8860

5. Replace the Natural gas orifice spud with the correct LP gas

orifice spud. See the “LP Gas Orifice Spud Chart.” On dual

burners (on some models), replace the center and outer

spuds.

6. Replace burner base and hand tighten the screws.

7. Replace burner cap.

8. Repeat steps 1 through 7 for the remaining burners.

9. Place Natural gas orifice spuds in plastic parts bag for future

use and keep with package containing literature.

10. Replace burner grates.

11. Complete installation. See “Make Gas Connection” and

“Electronic Ignition System” sections.

Checking for proper cooktop burner flame is very important.

The small inner cone should have a very distinct blue flame

¼" to ½" long. The outer cone is not as distinct as the inner

cone. LP gas flames have a slightly yellow tip.

IMPORTANT: You may have to adjust the “LO” setting for

each cooktop burner.

A. Plastic cover

B. Regulator cap

A. Natural gas position

B. LP gas position

C. Plastic cover

A. Burner cap

B. Gas tube opening

C. Burner base screws

D. Burner base

A. Natural gas orifice spud

B. Dual burner

C. Single burner

Location Burner Rating Color Number

Right Front 14,000 BTU Red 114L

Right Rear 4,000 BTU Blue 64L

Left Front 13,000 BTU Center: White

Outer: Orange

Center: 55L

Outer: 97L

Left Rear 9,100 BTU Clear 91L

Natural Gas Conversion

1. Turn manual shutoff valve to the closed position.

2. Unplug range or disconnect power.

To Convert Gas Pressure Regulator

3. Locate gas pressure regulator at the back of the range.

IMPORTANT: Do not remove the gas pressure regulator.

4. Unscrew the regulator cap and remove the plastic cover.

5. Flip the regulator cap over and replace the plastic cover.

6. Screw the regulator cap securely back into place. Do not

overtighten.

To Convert Surface Burners

1. If they are installed, remove the burner grates.

2. Remove the burner caps.

3. On models with a dual burner, remove the LP choke from the

dual burner.

4. Using a Phillips screwdriver, remove the burner base.

A. To range

B. Shutoff valve (closed position)

C. Gas supply line

WARNING

Tip Over Hazard

A child or adult can tip the range and be killed.

Install anti-tip bracket to floor or wall per installation

instructions.

Slide range back so rear range foot is engaged in the

slot of the anti-tip bracket.

Re-engage anti-tip bracket if range is moved.

Do not operate range without anti-tip bracket installed

and engaged.

Failure to follow these instructions can result in death

or serious burns to children and adults.

A. Plastic cover

B. Regulator cap

A. LP gas position

B. Natural gas position

C. Plastic cover

A. Burner cap

B. Gas tube opening

C. Burner base screws

D. Burner base

5. Apply masking tape to the end of a ⁹⁄₃₂" (7 mm) nut driver to

help hold the LP gas orifice spud in the nut driver while

changing it. Press nut driver down onto the LP gas orifice

spud and remove by turning it counterclockwise and lifting

out. Set the LP gas orifice spud aside.

Use the following chart for correct Natural gas orifice spud for

each burner. Refer to the gas information plate on the lower left

side of the front frame for proper sizing of Natural orifice spuds

for each burner location.

Natural Gas Orifice Spud Chart for Models JDS8850 and

JDS8860

6. Replace the LP gas orifice spud with correct Natural gas

orifice spud. See the “Natural Gas Orifice Spud Chart.”

7. Replace burner base and hand tighten the screws.

8. Replace burner cap.

9. Repeat steps 1 through 7 for the remaining burners.

10. Place LP gas orifice spuds (and LP choke on models with a

dual burner) in plastic parts bag for future use and keep with

package containing literature.

11. Replace burner grates.

12. Complete installation. See “Make Gas Connection” and

“Electronic Ignition System” sections.

Checking for proper cooktop burner flame is very important.

The small inner cone should have a very distinct blue flame

¼" to ½" long. The outer cone is not as distinct as the inner

cone. Natural gas flames do not have yellow tips.

IMPORTANT: You may have to adjust the “LO” setting for

each cooktop burner.

A. Natural gas orifice spud

B. Dual burner

C. Single burner

Location Burner Rating Color Number

Right Front 16,000 BTU Clear 190N

Right Rear 5,000 BTU Green 107N

Left Front 15,000 BTU Center: Clear

Outer: Clear

Center: 80N

Outer: 165N

Left Rear 9,200 BTU Clear 142N

SÉCURITÉ DE LA CUISINIÈRE

Risque possible de décès ou de blessure grave si vous ne

suivez pas immédiatement les instructions.

Risque possible de décès ou de blessure grave si vous

ne suivez pas les instructions.

Tous les messages de sécurité vous diront quel est le danger potentiel et vous disent comment réduire le risque de blessure et

ce qui peut se produire en cas de non-respect des instructions.

Votre sécurité et celle des autres est très importante.

Nous donnons de nombreux messages de sécurité importants dans ce manuel et sur votre appareil ménager. Assurez-vous de

toujours lire tous les messages de sécurité et de vous y conformer.

AVERTISSEMENT

DANGER

Voici le symbole d’alerte de sécurité.

Ce symbole d’alerte de sécurité vous signale les dangers potentiels de décès et de blessures graves à vous

et à d’autres.

Tous les messages de sécurité suivront le symbole d’alerte de sécurité et le mot “DANGER” ou

“AVERTISSEMENT”. Ces mots signifient :

AVERTISSEMENT : Si les renseignements dans ce manuel ne sont pas exactement

observés, un incendie ou une explosion peut survenir, causant des dommages au

produit, des blessures ou un décès.

– Ne pas entreposer ni utiliser de l’essence ou d’autres vapeurs ou liquides inflammables

à proximité de cet appareil ou de tout autre appareil électroménager.

– QUE FAIRE DANS LE CAS D’UNE ODEUR DE GAZ :

•

Ne pas tenter d’allumer un appareil.

•

Ne pas toucher à un commutateur électrique.

•

Ne pas utiliser le téléphone se trouvant sur les lieux.

•

Appeler immédiatement le fournisseur de gaz à partir du téléphone d'un voisin. Suivre

ses instructions.

•

À défaut de joindre votre fournisseur de gaz, appeler les pompiers.

– L’installation et l’entretien doivent être effectués par un installateur qualifié, une agence

de service ou le fournisseur de gaz.

AVERTISSEMENT : L’odorat ne permet pas toujours la détection d’une fuite de gaz.

Les distributeurs de gaz recommandent l’emploi d’un détecteur de gaz (homologation UL ou CSA).

Pour d’autre information, contacter le fournisseur de gaz local.

En cas de détection d’une fuite de gaz, exécuter les instructions “Que faire dans le cas d’une odeur de gaz”.

Dans l’État du Massachusetts, les instructions d’installation suivantes sont applicables :

■ Les travaux d’installation et réparation doivent être exécutés par un plombier ou tuyauteur qualifié ou licencié, ou par le

personnel qualifié d’une entreprise licenciée par l’État du Massachusetts.

■ Si une vanne à boisseau sphérique est utilisée, elle doit comporter une manette “T”.

■ Si un conduit de raccordement flexible est utilisé, sa longueur ne doit pas dépasser 3 pi.

EXIGENCES D’INSTALLATION

Outillage et pièces

Rassembler les outils et composants nécessaires avant

d'entreprendre l'installation. Lire et observer les instructions

fournies avec chacun des outils de la liste ci-dessous.

Outils nécessaires

Pièces fournies

Vérifier que toutes les pièces sont présentes.

■ Ensemble de conversion pour gaz propane/naturel (fixé au

support du détendeur à l'arrière de la cuisinière)

■ 5 - Chapeaux de brûleur

■ 2 - Grilles de brûleur

■ 3 - Grilles de four

■ 2 - Vis n° 12 x 1⁵⁄₈" (pour le montage de la bride

antibasculement)

■ 1 - Bande métallique de mise à la terre (pour un

raccordement à 3 conducteurs)

■ Bride antibasculement (fixée au sachet de documentation)

La bride antibasculement doit être bien fixée à la cloison

arrière ou au plancher. L'épaisseur du plancher peut

nécessiter des vis plus longues pour l'ancrage de la bride

dans le sous-plancher. Des vis plus longues sont disponibles

auprès de votre quincaillerie locale.

Pièces nécessaires

Vérifier les codes locaux et consulter le fournisseur de gaz.

Vérifier l'alimentation en gaz et l'alimentation électrique

existantes. Voir les sections “Spécifications électriques” et

“Spécifications de l'alimentation en gaz”.

Exigences d'emplacement

IMPORTANT : Observer les dispositions de tous les codes et

règlements en vigueur. Ne pas obstruer le flux de combustion et

de ventilation.

■ C'est à l'installateur qu'incombe la responsabilité de

respecter les distances de séparation exigées pour

l'installation, spécifiées sur la plaque signalétique de

l'appareil. La plaque signalétique est située sur le côté droit

du châssis du four, derrière le panneau du tiroir de remisage.

■ La cuisinière doit être installée à un endroit pratique dans la

cuisine.

■ Dans le cas d'une cuisinière encastrée, l'enceinte doit

recouvrir complètement les côtés et l'arrière de la cuisinière.

Risque de basculement

Un enfant ou une personne adulte peut faire basculer la cuisinière, ce qui peut causer un

décès.

Fixer la bride antibasculement au plancher ou au mur, conformément aux instructions

d'installation.

Faire glisser de nouveau la cuisinière de façon à ce que le pied arrière de la cuisinière se

trouve dans la fente de la bride antibasculement.

Réengager la bride antibasculement si la cuisinière a été déplacée.

Ne pas faire fonctionner la cuisinière si la bride antibasculement n'est pas installée et engagée.

Le non-respect de ces instructions peut causer un décès ou des brûlures graves aux enfants et

aux adultes.

Pour vérifier que la bride antibasculement est bien installée et engagée :

• Faire glisser la cuisinière vers l'avant.

• Vérifier que la bride antibasculement est bien fixée au plancher ou au mur.

• Faire de nouveau glisser la cuisinière vers l'arrière de sorte que le pied de la cuisinière

se trouve sous la bride antibasculement.

• Voir les instructions d'installation pour plus de détails.

AVERTISSEMENT

Bride

antibasculement

Pied de la cuisinière

■ Mètre-ruban

■ Tournevis Phillips

■ Tournevis à lame plate

■ Tournevis à lame plate de ¹⁄₈"

■ Niveau

■ Perceuse manuelle ou

électrique

■ Clé ou pince

■ Clé à tuyauterie

■ Clé mixte de ¹⁵⁄₁₆"

■ Foret de ¹⁄₈" (3,2 mm) (pour

planchers en bois)

■ Marqueur ou crayon

■ Composé d’étanchéité des

raccords filetés – résistant

au gaz propane

■ Foret à maçonnerie à pointe

carburée de ³⁄₁₆" (4,8 mm)

(pour planchers en béton/

céramique)

■ Solution non-corrosive de

détection des fuites

Pour conversions pour gaz

propane/naturel

■ Clé mixte de ½"

■ Tourne-écrou de ¼" (6 mm)

■ Tourne-écrou de ⁹⁄₃₂" (7 mm)

■ Ruban adhésif de masquage

■ Afin de supprimer le risque de brûlures ou d'incendie lié au

fait de se pencher au-dessus des unités de surface

chauffées, le rangement en placard au-dessus des unités de

surface doit être évité. Si le rangement en placard est

envisagé, le risque peut être réduit par l'installation d'une

hotte de cuisinière ou un ensemble hotte/micro-ondes

opérant horizontalement sur un minimum de 5" (12,7 cm) au-

delà du bas des placards.

■ Toutes les ouvertures dans le mur ou le plancher de

l'emplacement d'installation de la cuisinière doivent être

scellées.

■ Respecter les dimensions indiquées pour les ouvertures à

découper dans les placards. Ces dimensions constituent les

valeurs minimales des dégagements de séparation.

■ La bride antibasculement de plancher doit être installée. Pour

l'installation de la bride antibasculement expédiée avec la

cuisinière, voir la section “Installation de la bride

antibasculement”.

■ Une source d'électricité avec liaison à la terre est nécessaire.

Voir la section “Spécifications électriques”.

■ Une source de gaz adéquate doit être disponible. Voir la

section “Spécifications de l'alimentation en gaz”.

■ Contacter un installateur de revêtement de sol qualifié, qui

pourra déterminer si le revêtement de sol peut résister à une

température d'au moins 200°F (93°C).

■ Dans le cas de l'installation de la cuisinière par dessus un

tapis, placer sous la cuisinière une plaque d'appui isolée, ou

une plaque de contreplaqué de ¼" (0,64 cm).

IMPORTANT : Afin d'éviter d’endommager les placards,

consulter le constructeur de la maison ou le vendeur des

placards pour déterminer si les matériaux utilisés peuvent subir

un changement de couleur, une déstratification ou d'autres

dommages. Ce four a été conçu conformément aux exigences

des normes UL et CSA International et respecte les températures

maximales permises de 194°F (90°C) pour les placards en bois.

Résidence mobile – Spécifications additionnelles à

respecter lors de l'installation

L'installation de cette cuisinière doit être conforme aux

dispositions de la norme Manufactured Home Construction and

Safety Standard, Title 24 CFR, Part 3280 (anciennement Federal

Standard for Mobile Home Construction and Safety, Title 24,

HUD Part 280). Lorsque cette norme n'est pas applicable,

l'installation doit satisfaire aux critères de la norme Standard for

Manufactured Home Installations, ANSI A225.1/NFPA 501A ou

aux dispositions des codes locaux.

Au Canada, l'installation de cette cuisinière doit satisfaire aux

stipulations de la version la plus récente de la norme CAN/CSA-

A240 ou des codes locaux en vigueur.

Critères à respecter pour une installation en résidence

mobile :

■ Dans le cas de l'installation de cette cuisinière dans une

résidence mobile, la cuisinière doit être fixée au plancher

durant tout déplacement du véhicule. Toute méthode de

fixation de la cuisinière est adéquate dans la mesure où elle

satisfait aux critères des normes mentionnées ci-dessus.

Dimensions du produit

Modèle JDS88550

Modèle JDS8860

REMARQUE : La table de cuisson illustrée peut différer de votre

modèle.

A. 30³⁄₄" (78,1 cm)

B. Hauteur jusqu’à la partie

inférieure de la table de cuisson

avec les pieds de nivellement

complètement relevés : 35

³⁄₄

(90,8 cm)*

C. Plaque signalétique (située sur le

côté droit du châssis du four,

derrière le tiroir de remisage)

D. 29⁷⁄₈" (75,9 cm)

E. Plaque d'information sur le

gaz (située sur le côté

gauche du châssis du four,

derrière le tiroir de remisage)

F. 29" (73,4 cm) entre la

poignée et l'arrière de la

cuisinière**

G. 23" (58,4 cm) entre le coin

du plan de travail et l’arrière

de la table de cuisson

⁷⁄₈" (78,4 cm)

B. Hauteur jusqu’à la partie

inférieure de la table de

cuisson avec les pieds de

nivellement complètement

relevés : 35

³⁄₄

" (90,8 cm)*

C. Plaque signalétique (située

sur le côté droit du châssis du

four, derrière le tiroir de

remisage)

D. 29

⁷⁄₈

" (75,9 cm)

E. Plaque d'informations sur le

gaz (située sur le côté gauche

du châssis du four, derrière le

tiroir de remisage)

F. 29" (73,7 cm) de la poignée à

l’arrière de la cuisinière**

G. Du coin du plan de travail à

l’arrière de la table de

cuisson : 27" (68,6 cm)

La page charge ...

Jenn-Air Pro-Style JDS8860BDP Installation Instructions Manual

Marque: Jenn-Air

Modèle: Pro-Style JDS8860BDP

Taper: Installation Instructions Manual

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Jenn-Air Pro-Style JDS8860BDP

Jenn-Air Pro-Style JDS8860BDP Installation Instructions Manual

Ce manuel convient également à

Jenn-Air Pro-Style JDS8860BDP Installation Instructions Manual

dans d''autres langues

Documents connexes

Autres documents