Genesis S-320 Le manuel du propriétaire

YOU MUST READ THIS OWNER’S GUIDE

BEFORE OPERATING YOUR GAS GRILL

 DANGER

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open flames.

3. Open lid.

4. If odor continues, keep away from the

appliance and immediately call your gas

supplier or your fire department.

Leaking gas may cause a fire or explosion

which can cause serious bodily injury or

death, or damage to property.

 WARNING:

1. Do not store or use gasoline or other

flammable liquids or vapors in the

vicinity of this or any other appliance.

2. An LP cylinder not connected for use

shall not be stored in the vicinity of this

or any other appliance.

 WARNING: Follow all leak-check

procedures carefully in this manual prior

to barbecue operation. Do this even if the

barbecue was dealer-assembled.

NOTICE TO INSTALLER: These instructions

must be left with the owner and the owner

should keep them for future use.

THIS GAS APPLIANCE IS DESIGNED FOR

OUTDOOR USE ONLY.

89555 02/20/08 LP

US ENGLISH

GAS GRILL

#00000

#89555

 WARNING: Do not try to light this

appliance without reading the “Lighting

Instructions” section of this manual.

LP GAS GRILL OWNER’S GUIDE

E/S -310/320, EP -310/320

Guía del propietario del asador de gas licuado de propano - Pg 20

Guide de l’utilisateur du grill à gaz PL - Pg 34

2

WWW.WEBER.COM

®

DANGERS AND WARNINGS

 DANGER

Failure to follow the Dangers, Warnings and Cautions contained in this Owner’s Manual may result in serious bodily injury or

death, or in a fire or an explosion causing damage to property.

 WARNINGS

 Do not store a spare or disconnected liquid propane cylinder under or near this barbecue.

 Improper assembly may be dangerous. Please follow the assembly instructions carefully.

 After a period of storage, and/or nonuse, the Weber

®

gas barbecue should be checked for gas leaks and burner obstructions

before use. See instructions in this manual for correct procedures.

 Do not operate the Weber

®

gas barbecue if there is a gas leak present.

 Do not use a flame to check for gas leaks.

 Combustible materials should never be within 24 inches (61 cm) of the back or sides of your Weber

®

gas barbecue.

 Do not put a barbecue cover or anything flammable on, or in the storage area under the barbecue.

 Your Weber

®

gas barbecue should never be used by children. Accessible parts of the barbecue may be very hot. Keep young

children away while it is in use.

 You should exercise reasonable care when operating your Weber

®

gas barbecue. It will be hot during cooking or cleaning and

should never be left unattended, or moved while in operation.

 Should the burners go out while in operation, turn all gas valves off. Open the lid and wait five minutes before attempting to

relight, using the lighting instructions.

 Do not use charcoal or lava rock in your Weber

®

gas barbecue.

 Never lean over open grill or place hands or fingers on the front edge of the cooking box.

 Should a grease fire occur, turn off all burners and leave lid closed until fire is out.

 Do not enlarge valve orifices or burner ports when cleaning the valves or burners.

 The Weber

®

gas barbecue should be thoroughly cleaned on a regular basis.

 Liquid propane gas is not natural gas. The conversion or attempted use of natural gas in a liquid propane unit or liquid propane

gas in a natural gas unit is dangerous and will void your warranty.

 Do not attempt to disconnect any gas fitting while your barbecue is in operation.

 Use heat-resistant barbecue mitts or gloves when operating barbecue.

 Keep any electrical supply cord and the fuel supply hose away from any heated surfaces.

 Combustion byproducts produced when using this product contain chemicals known to the state of California to cause cancer,

birth defects, or other reproductive harm.

 Do not use this barbecue unless all parts are in place. The unit must be properly assembled according to the assembly

instructions.

 Do not build this model of grill in any built-in or slide in construction. Ignoring this Warning could cause a fire or an explosion

that can damage property and cause serious bodily injury or death.

 Proposition 65 Warning: Handling the brass material on this product exposes you to lead, a chemical known to the state of

California to cause cancer, birth defects or other reproductive harm.

(Wash hands after handling this product.)

LIQUID PROPANE GAS UNITS ONLY:

 Use the pressure regulator and hose assembly that is supplied with your Weber

®

gas barbecue.

 Do not attempt to disconnect the gas regulator and hose assembly or any gas fitting while your barbecue is in operation.

 A dented or rusty liquid propane cylinder may be hazardous and should be checked by your liquid propane supplier. Do not

use a liquid propane cylinder with a damaged valve.

 Although your liquid propane cylinder may appear to be empty, gas may still be present, and the cylinder should be

transported and stored accordingly.

 If you see, smell or hear the hiss of escaping gas from the liquid propane cylinder:

1. Move away from liquid propane cylinder.

2. Do not attempt to correct the problem yourself.

3. Call your fire department.

WARNINGS

3

WWW.WEBER.COM

®

3

WARRANTY

WARRANTY, GARANTÍA, GARANTIE

WARRANTY

Weber-Stephen Products Co. (Weber) hereby warrants to the ORIGINAL PURCHASER of this Weber

®

gas grill that it will be free of defects in material and workmanship from the date of purchase as follows:

Aluminum castings 25-years (2 years on paint; excludes fading)

Stainless steel Shroud, 25-years;

Porcelain-enameled shroud, 25-years

Cookbox Assembly 10-years (2 year on paint excludes fading)

Stainless steel burners tubes, 10-years

Stainless steel cooking grates, 5-years no rust through or burn through

Stainless steel Flavorizer bars, 5-years no rust through or burn through

Porcelain-enameled cast-iron

cooking grates, 5-year no rust through or burn through

Porcelain-enameled

cooking grates, 3-years no rust through or burn through

Porcelain-enameled

Flavorizer bars, 2-years no rust through or burn through

Infrared Rotisserie Burner, 2-years

All remaining parts, 2-years

When assembled and operated in accordance with the printed instructions accompanying it.

Weber may require reasonable proof of your date of purchase. THEREFORE, YOU SHOULD RETAIN

YOUR SALES SLIP OR INVOICE.

This Limited Warranty shall be limited to the repair or replacement of parts that prove defective under

normal use and service and which on examination shall indicate, to Weber’s satisfaction, they are

defective. Before returning any parts, contact the Customer Service Representative in your area

using the contact information on our website. If Weber confirms the defect and approves the claim,

Weber will elect to replace such parts without charge. If you are required to return defective parts,

transportation charges must be prepaid. Weber will return parts to the purchaser, freight or postage

prepaid.

This Limited Warranty does not cover any failures or operating difficulties due to accident, abuse,

misuse, alteration, misapplication, vandalism, improper installation or improper maintenance or

service, or failure to perform normal and routine maintenance, including but not limited to damage

caused by insects within the burner tubes, as set out in this owner’s manual.

Deterioration or damage due to severe weather conditions such as hail, hurricanes, earthquakes

or tornadoes, discoloration due to exposure to chemicals either directly or in the atmosphere, is not

covered by this Limited Warranty.

There are no other express warrants except as set forth herein and any applicable implied warranties

of merchantability and fitness are limited in duration to the period of coverage of this express written

Limited Warranty. Some regions do not allow limitation on how long an implied warranty lasts, so this

limitation may not apply to you.

Weber is not liable for any special, indirect or consequential damages. Some regions do not allow the

exclusion or limitation of incidental or consequential damages, so this limitation or exclusion may not

apply to you.

Weber does not authorize any person or company to assume for it any other obligation or liability in

connection with the sale, installation, use, removal, return, or replacement of its equipment; and no

such representations are binding on Weber.

This Warranty applies only to products sold at retail.

WEBER-STEPHEN PRODUCTS CO.

Customer Service Center

1890 Roselle Road, Suite 308

Schaumburg, IL 60195

USA

For replacement parts call:

1-800-446-1071

www.weber.com

®

Weber-Stephen Products Co., (Weber) mediante la presente le garantiza al COMPRADOR ORIGINAL

de esta barbacoa de gas Weber

®

que la misma estará libre de defectos en cuanto a materiales y

fabricación a partir de la fecha de compra según lo siguiente:

Piezas coladas de aluminio 25-años (2 años para la pintura excluyendo la decoloración)

Cubierta de acero inoxidable, 25-años

Cubierta porcelanizada, 25-años

Cámara para asar 10-años (2 años para la pintura excluyendo la decoloración)

Tubos de acero inoxidable

de los quemadores, 10-años

Parrilas de cocción de

acero inoxidable, 5-años sin pertoración por fuego u oxidación

Barras Flavorizer de

acero inoxidable, 5-años sin pertoración por fuego u oxidación

Parrillas de cocción de hierro

colado porcelanizado, 5-años sin pertoración por fuego u oxidación

Parrillas de cocción porcenlanizadas, 3-años sin pertoración por fuego u oxidación

Barras Flavorizer porcelanizadas, 2-años sin pertoración por fuego u oxidación

Qumeador infrarrojo del

asador giratorio, 2-años

Todas la demás partes, 2-años

cuando se ensambla y opera de acuerdo a las instrucciones impresas que la acompañan.

Weber pudiese requerir prueba razonable de la fecha de compra. POR LO TANTO, DEBERÁ

GUARDAR SU RECIBO O FACTURA DE VENTA.

Esta garantía limitada está limitada a la reparación o reemplazo de piezas que resultasen defectuosas

bajo uso y servicio normal y las cuales al examinarse indiquen, a plena satisfacción de Weber, que

efectivamente son piezas defectuosas. Antes de devolver cualquier parte, contacte al Representante

de Atención al Cliente en su área, cuya información de contacto la encontrará en nuestro sitio web. Si

Weber confirma el defecto y aprueba el reclamo, ésta elegirá reparar o reemplazar tal pieza sin cargo

alguno. Si usted tiene que retornarnos las partes defectuosas, los gastos de transporte deben ser

prepagados. Weber retornará las partes al comprador con transporte o franqueo prepagado.

Esta Garantía Limitada no cubre ninguna falla o problema de operación a causa de accidentes,

abuso, mal uso, alteración, uso en aplicaciones indebidas, vandalismo, instalación inapropiada o

mantenimiento o servicio inapropiados, o por no llevar a cabo el mantenimiento normal y rutinario,

entre los que se incluyen, pero sin limitación, los daños causados por insectos dentro de los tubos

quemadores, según se detalla en este manual del propietario.

Esta Garantía Limitada no cubre el deterioro o daños a causa de condiciones de tiempo inclemente

tales como granizo, huracanes, terremotos o tornados ni tampoco la decoloración por exposición a

sustancias químicas bien sea por contacto directo o por que las mismas contenidas en la atmósfera.

No existe ninguna otra garantía expresa que no sean las las acá indicadas y cualesquier garantías

implícitas de comerciabilidad y aptitud de uso están limitadas en duración al tiempo de cobertura de

esta expresa Garantía Limitada por escrito. Algunas regiones no permiten limitación alguna en el

tiempo que una garantía implícita pueda durar, por lo que esta limitación pudiera no aplicarle a usted.

Weber no se hace responsable de cualesquier daños especiales, indirectos o emergentes. Algunas

regiones no permiten la exclusión o limitación de daños incidentales o emergentes, por lo que esta

limitación o exclusión pudieran no aplicarle a usted.

Weber no autoriza a persona o empresa alguna a asumir en su nombre ninguna obligación o

responsabilidad en relación con la venta, instalación, uso, retiro, devolución o reemplazo de sus

equipos, y ninguna tal representación será vinculante para Weber.

Esta Garantía aplica solo a aquellos productos vendidos al por menor.

WEBER-STEPHEN PRODUCTS CO.

Customer Service Center

1890 Roselle Road, Suite 308

Schaumburg, IL 60195

USA

Para partes de repuesto llame a:

1-800-446-1071

www.weber.com

®

Weber-Stephen Products Co. (Weber) garantit par le présent document à l’ACHETEUR D’ORIGINE de

ce grill à gaz Weber

®

que celui-ci ne comportera aucun défaut de pièce ni de main d’oeuvre à compter

de la date d’achat comme suit :

Fonte d’aluminium 25 ans (2 ans pour lapeinture à l’exception de toute décoloration)

Structure en acier inoxydable, 25 ans

Structure émaillée, 25 ans

Cuve, 10 ans (2 ans pour la peinture à l’exception de toute décoloration)

Tubes du brûleur en acier inoxydable, 10 ans

Grilles de cuisson en acier inoxydable, 5 ans sans trou provoqué par la rouille ou par une brûlure

Barres Flavorizer en acier inoxydable, 5 ans sans trou provoqué par la rouille ou par une brûlure

Grilles de cuisson en fonte fer émaillée, 5 ans sans trou provoqué par la rouille ou par une brûlure

Grilles de cuisson émaillées, 3 ans sans trou provoqué par la rouille ou par une brûlure

Barres Flavorizer émaillées, 2 ans sans trou provoqué par la rouille ou par une brûlure

Brûleur de la rôtissoire à infrarouge, 2 ans

Toutes les autres pièces, 2 ans

à condition qu’il ait été assemblé et utilisé conformément aux instructions imprimées qui

l’accompagnent.

Weber peut exiger une preuve raisonnable de votre date d’achat. VOUS DEVRIEZ DONC

CONSERVER VOTRE TICKET DE CAISSE OU VOTRE FACTURE.

La présente Garantie limitée est limitée à la réparation ou au remplacement des pièces qui s’avèrent

défectueuses dans le cadre d’une utilisation normale et d’un entretien normal et dont l’examen indique,

à la satisfaction de Weber, qu’elles sont défectueuses. Avant de retourner toute pièce, veuillez

entrer en contact avec le Représentant du Service clientèle le plus proche grâce aux coordonnées

à votre disposition sur notre site Internet. Si Weber confirme le défaut et approuve la demande,

Weber choisira de remplacer ces pièces sans frais. S’il vous est demandé de retourner les pièces

défectueuses, les frais de transport devront être prépayés. Weber retournera les pièces à l’acheteur,

franco de port.

La présente Garantie limitée ne couvre pas toute défaillance ou difficulté d’utilisation provoquée par un

accident, une utilisation abusive, une mauvaise utilisation, une altération, une mauvaise application, un

acte de vandalisme, une installation incorrecte ou une maintenance ou un entretien incorrects, ou le

défaut d’entretien normal et régulier, y compris mais pas seulement les dommages provoqués par des

insectes à l’intérieur des tubes du brûleur, tel que décrit dans le présent mode d’emploi.

Toute détérioration ou tout dommage résultant de conditions météorologiques graves comme de la

grêle, des ouragans, des séismes ou des tornades, toute décoloration résultant d’une exposition à des

agents chimiques directement ou dans l’atmosphère, n’est pas couverte dans le cadre de la présente

Garantie limitée.

Il n’existe aucune autre garantie expresse hormis celles exposées dans le présent document et toute

garantie de commercialisation et de bon état induite est limitée en durée à la période de couverture de

la présente Garantie limitée écrite expresse. Certaines régions n’autorisent pas de limitation de durée

de la garantie induite ; il est donc posible que cette limitation ne s’applique pas à vous.

Weber ne peut être tenu pour responsable de tout dommage particulier, induit ou se produisant par

voie de conséquence. Certaines régions n’autorisent pas l’exclusion ou la limitation des dommages

indirects ou se produisant par voie de conséquence ; il est donc possible que cette limitation ou

exclusion ne s’applique pas à vous.

Weber n’autorise aucune personne ou société à présumer en son nom de toute autre obligation

ou responsabilité en relation avec la vente, l’installation, l’utilisation, le retrait, le retour ou le

remplacement de ses équipements ; et aucune de ces représentations ne lie Weber.

La présente Garantie s’applique uniquement aux produits vendus au détail.

WEBER-STEPHEN PRODUCTS CO.

Product Registration

P.O. Box 40530

Burlington, ON L7P 4W1

Pour des pièces de rechange, appelez le :

1-800-265-2150

www.weber.com

®

Para compras hechas en México

WEBER-STEPHEN PRODUCTS S.A. de C.V.

Marcella No. 338,

Colonia Americana

44160 México, C.P.

México

Para partes de repuesto llame a:

(52) (33) 3615-0736

www.weber.com

®

4

WWW.WEBER.COM

®

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

35

34

36

37

38

39

41

42

43

44

46

47

6

40

45

2

3

1

4

5

Genesis_310_LP_US

EXPLODED VIEW E/S/EP 310

VISION ÉCLATÉE, DIAGRAMA DE DESPIECE

Structure de protection

Thermomètre

Plaque indicatrice du thermomètre

Tôle de protection

Poignée

Grille de réchauffage

Tablette latérale gauche

Grilles de cuisson

Tuyau Crossover

®

Boîtier de cuisson

Panneau du cadre gauche

Support arrière du cadre

Support avant du cadre

Pièce de garniture gauche

Pièce de garniture avant gauche

Support d’égouttoir

Egouttoir jetable

Egouttoir

Panneau avant

Porte gauche

Porte droite

Poignée de porte

Bouton de commande

Plaque indicatrice N° 3

Plaque indicatrice N° 2

Plaque indicatrice N° 1

Bouton d’allumage

Module d’allumage

Tablette latérale droite

Barre Flavorizer

®

Tube du brûleur arrière

Tube du brûleur du milieu

Tube du brûleur avant

Igniter Electrode

Panneau arrière

Plateau de la bouteille

Collecteur

Tuyau/Régulateur

Panneau du cadre droit

Glissières de la bouteille

Egouttoir

Pièce de garniture droite

Porte-allumette

Pièce de garniture avant droite

Roulette

Panneau inférieur

Roulette autobloquante

Accesorios de la cubierta

Termómetro

Moldura decorativa del termómetro

Cubierta

Asa

Rejilla de calentamiento

Mesa lateral izquierda

Parrillas de cocción

Tubo Crossover

®

Caja de cocción

Panel izquierdo del bastidor

Soporte posterior del bastidor

Soporte delantero del bastidor

Pieza de guarnición izquierda

Pieza de guarnición frontal izquierda

Soporte del plato recolector

Bandeja de goteo desechable

Plato recolector

Panel frontal

Puerta izquierda

Puerta derecha

Asa de la puerta

Perilla de control

Moldura decorativa #3

Moldura decorativa #2

Moldura decorativa #1

Botón de encendido

Módulo de encendido

Mesa lateral derecha

Barra Flavorizer

®

Tubo quemador posterior

Tubo quemador del medio

Tubo quemador frontal

Electrodo del encendedor

Panel trasero

Báscula del tanque

Múltiple

Manguera / Regulador

Panel derecho del bastidor

Deslizaderas del tanque

Bandeja de goteo

Pieza de guarnición derecha

Portacerillos

Pieza de guarnición frontal derecha

Rueda giratoria

Panel inferior

Rueda giratoria con bloqueo

5

WWW.WEBER.COM

®

5

Shroud Hardware1.

Thermometer2.

Thermometer Bezel3.

Shroud4.

Handle5.

Warming Rack6.

Left Side Table7.

Cooking Grates8.

Crossover9.

®

Tube

Cookbox10.

Left Frame Panel11.

Rear Frame Support12.

Front Frame Support13.

Left Trim Piece14.

Left Front Trim Piece15.

Catch Pan Holder16.

Disposable Drip Pan17.

LISTA DEL DIAGRAMA DE DESPIECE, LISTE DE LA VISION ÉCLATÉE

Catch Pan18.

Front Panel19.

Left Door20.

Right Door21.

Door Handle22.

Control Knob23.

Bezel #324.

Bezel #225.

Bezel #126.

Igniter Button27.

Igniter Module28.

Right Side Table29.

Flavorizer30.

®

Bar

Rear Burner Tube31.

Middle Burner Tube32.

Front Burner Tube33.

Igniter Electrode34.

Back Panel35.

Tank Scale36.

Manifold37.

Hose / Regulator38.

Right Frame Panel39.

Tank Glides40.

Drip Tray41.

Right Trim Piece42.

Matchstick Holder43.

Right Front Trim Piece44.

Caster45.

Bottom Panel46.

Locking Caster47.

EXPLODED VIEW LIST E/S/EP 310

6

WWW.WEBER.COM

®

7

8

9

10

11

12

13

15

14

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

44

45

46

47

49

50

43

48

42

2

3

1

4

5

6

Genesis_320_LP_US

EXPLODED VIEW E/S/EP 320

VISION ÉCLATÉE, DIAGRAMA DE DESPIECE

Structure de protection

Thermomètre

Plaque indicatrice du thermomètre

Tôle de protection

Poignée

Grille de réchauffage

Tablette du brûleur latéral

Couvercle du brûleur latéral

Grilles de cuisson

Brûleur latéral

Tuyau Crossover

Boîtier de cuisson

Panneau du cadre gauche

Support arrière du cadre

Support avant du cadre

Pièce de garniture gauche

Pièce de garniture avant gauche

Support d’égouttoir

Egouttoir jetable

Egouttoir

Panneau avant

Porte gauche

Porte droite

Poignée de porte

Bouton de commande

Plaque indicatrice N° 3

Plaque indicatrice N° 2

Plaque indicatrice N° 1

Bouton d’allumage

Module d’allumage

Tablette latérale droite

Barre Flavorizer

®

Tube du brûleur arrière

Tube du brûleur du milieu

Tube du brûleur avant

Igniter Eectrode

Panneau arrière

Plateau de la bouteille

Collecteur

Tuyau/Régulateur

Panneau du cadre droit

Tuyau du collecteur

Glissières de la bouteille

Egouttoir

Pièce de garniture droite

Porte-allumette

Pièce de garniture avant droite

Roulette

Panneau inférieur

Roulette autobloquante

Accesorios de la cubierta

Termómetro

Moldura decorativa del termómetro

Cubierta

Asa

Rejilla de calentamiento

Mesa del quemador lateral

Tapa del quemador lateral

Parrillas de cocción

Quemador lateral

Tubo Crossover

Caja de cocción

Panel izquierdo del bastidor

Soporte posterior del bastidor

Soporte delantero del bastidor

Pieza de guarnición izquierda

Pieza de guarnición frontal izquierda

Soporte del plato recolector

Bandeja de goteo desechable

Plato recolector

Panel frontal

Puerta izquierda

Puerta derecha

Asa de la puerta

Perilla de control

Moldura decorativa #3

Moldura decorativa #2

Moldura decorativa #1

Botón de encendido

Módulo de encendido

Mesa lateral derecha

Barra Flavorizer

®

Tubo quemador posterior

Tubo quemador del medio

Tubo quemador frontal

Electrodo del encendedor

Panel trasero

Báscula del tanque

Múltiple

Manguera / Regulador

Panel derecho del bastidor

Manguera del múltiple

Deslizaderas del tanque

Bandeja de goteo

Pieza de guarnición derecha

Portacerillos

Pieza de guarnición frontal derecha

Rueda giratoria

Panel inferior

Rueda giratoria con bloqueo

7

WWW.WEBER.COM

®

7

Shroud Hardware1.

Thermometer2.

Thermometer Bezel3.

Shroud4.

Handle5.

Warming Rack6.

Side Burner Table7.

Side Burner Lid8.

Cooking Grates9.

Side Burner10.

Crossover Tube11.

Cookbox12.

Left Frame Panel13.

Rear Frame Support14.

Front Frame Support15.

Left Trim Piece16.

Left Front Trim Piece17.

LISTA DEL DIAGRAMA DE DESPIECE, LISTE DE LA VISION ÉCLATÉE

Catch Pan Holder18.

Disposable Drip Pan19.

Catch Pan20.

Front Panel21.

Left Door22.

Right Door23.

Door Handle24.

Control Knob25.

Bezel #326.

Bezel #227.

Bezel #128.

Igniter Button29.

Igniter Module30.

Right Side Table31.

Flavorizer32.

®

Bar

Rear Burner Tube

33.

Middle Burner Tube34.

Front Burner Tube35.

Igniter Electrode36.

Back Panel37.

Tank Scale38.

Manifold39.

Hose / Regulator40.

Right Frame Panel41.

Manifold Hose42.

Tank Glides43.

Drip Tray44.

Right Trim Piece45.

Matchstick Holder46.

Right Front Trim Piece47.

Caster48.

Bottom Panel49.

Locking Caster50.

EXPLODED VIEW LIST E/S/EP 320

8

WWW.WEBER.COM

®

GENERAL INSTRUCTIONS

Your Weber

®

gas barbecue is a portable outdoor cooking appliance. With the Weber

®

gas barbecue you can grill, barbecue, roast and bake with results that are difficult to

duplicate with indoor kitchen appliances. The closed lid and Flavorizer

®

Bars produce

that “outdoor” flavor in the food.

The Weber

®

gas barbecue is portable so you can easily change its location in your yard

or on your patio. Portability means you can take your Weber

®

gas barbecue with, if you

move.

Liquid Propane (LP) gas supply is easy to use and gives you more cooking control than

charcoal fuel.

• These instructions will give you the minimum requirements for assembling your

Weber

®

gas barbecue. Please read the instructions carefully before using your

Weber

®

gas barbecue. Improper assembly can be dangerous.

• Not for use by children.

• If there are local codes that apply to portable gas grills, you will have to conform to

them. Installation must conform with local codes or, in the absence of local codes,

with either the National Fuel Gas Code, ANSI Z223.1/NFPA 54, Natural Gas and

Propane Installation Code, CSA B149.1, or Propane Storage and Handling Code,

B149.2, or the Standard for Recreational Vehicles, ANSI A 119.2/NFPA 1192, and

CSA Z240 RV Series, Recreational Vehicle Code, as applicable.

• The pressure regulator supplied with the Weber

®

gas barbecue must be used.

This regulator is set for 11 inches of water column (pressure).

• This Weber

®

gas barbecue is designed for use with liquid propane (LP) gas only.

Do not use with natural (piped in city) gas. The valves, orifices, hose and regulator

are for LP gas only.

• Do not use with charcoal fuel.

• Check that the area under the control panel and the bottom tray are free from

debris that might obstruct the flow of combustion or ventilation air.

• The areas around the LP cylinder must be free and clear from debris.

• Replacement pressure regulators and hose assemblies must be those specified

by Weber-Stephen Products Co.

FOR INSTALLATION IN CANADA

These instructions, while generally acceptable, do not necessarily comply with the

Canadian Installation codes, particularly with piping above and below ground. In

Canada the installation of this appliance must comply with local codes and/or Standard

CSA-B149.2 (Propane Storage and Handling Code).

OPERATING

 WARNING: Only use this barbecue outdoors in a well-

ventilated area. Do not use in a garage, building, breezeway

or any other enclosed area.

 WARNING: Keep ventilation openings for cylinder enclosure

free and clear from debris.

STORAGE AND/OR NONUSE

• The gas must be turned off at the liquid propane cylinder when the Weber

®

gas

barbecue is not in use.

• When the Weber

®

gas barbecue is stored indoors, the gas supply must be

DISCONNECTED and the LP cylinder stored outdoors in a well-ventilated space.

• LP cylinder must be stored outdoors in a well -ventilated area out of reach of

children. Disconnected LP cylinder must not be stored in a building, garage or any

other enclosed area.

• When the LP cylinder is not disconnected from the Weber

®

gas barbecue, the

appliance and LP tank must be kept outdoors in a well-ventilated space.

• The Weber

®

gas barbecue should be checked for gas leaks and any obstructions

in the burner tubes before using. (See Section: “Maintenance/Annual

Maintenance).

• Check that the areas under the control panel and the slide out bottom tray are free

from debris that might obstruct the flow of combustion or ventilation air.

• The Spider /Insect Screens should also be checked for any obstructions.

(See Section: "Maintenance/Annual Maintenance").

 WARNING: Your Weber

®

gas barbecue shall not be used

under overhead combustible construction.

 WARNING: Your Weber

®

gas barbecue is not intended to be

installed in or on recreational vehicles and/or boats.

 WARNING: Do not use the barbecue within 24 inches of

combustible materials to the back or sides of the grill.

 WARNING: The entire cooking box gets hot when in use. Do

not leave unattended.

 WARNING: Keep any electrical supply cord and the fuel

supply hose away from any heated surface.

 WARNING: Keep the cooking area clear of flammable vapors

and liquids such as gasoline, alcohol, etc., and combustible

materials.

 WARNING: Never store an extra (spare) LP cylinder under or

near the Weber

®

gas barbecue.

 WARNING: The LP cylinder used with your barbecue must

be with a listed OPD (Overfilling Prevention Device) and

a QCC1 or Type 1 (CGA810) cylinder connection. The

cylinder connection must be compatible with the barbecue

connection.

COOKING

 WARNING: Do not move the Weber

®

gas barbecue when

operating or while barbecue is hot.

You can adjust BURNER 1, 2, and 3 as desired. The control settings: High (H), Medium

(M), Low (L), or Off (O) are described in your Weber

®

cookbook. The cookbook uses

these notations to describe the settings of BURNER 1, 2, and 3. For example, to sear

steaks, you would set all burners at H (high). Then to complete cooking, you would set

BURNER 1 and BURNER 3 at M (medium). Refer to your Weber

®

cookbook for detailed

cooking instructions.

Note: The temperature inside your cooking box for the first few uses, while surfaces are

still very reflective, may be hotter than those shown in your cookbook. Cooking condi-

tions such as wind and weather, may require the adjustment of the burner controls to

obtain the correct cooking temperatures.

Preheating - Your Weber

®

gas barbecue is an energy-efficient appliance. It operates at

an economical low BTU rate. To preheat: after lighting, close lid and turn all burners to

high (H). Preheating to between 500° and 550° F (260° and 290° C) will take 10 to 15

minutes depending on conditions such as air temperature and wind.

Drippings and grease - The Flavorizer

®

bars are designed to “smoke” the correct

amount of drippings for flavorful cooking. Excess drippings and grease will accumulate in

the catch pan under the slide out bottom tray. Disposable foil drip pans are available that

fit the catch pan.

CLEANING

 WARNING: Turn your Weber

®

gas barbecue off and wait for it

to cool before cleaning.

 CAUTION: Do not clean your Flavorizer

®

bars or cooking

grates in a self-cleaning oven.

For availability of replacement cooking grates and Flavorizer

®

bars contact the

Customer Service Representative in your area using the contact information on

our website. Log onto www.weber.com

®

Outside surfaces - Use a warm soapy water solution to clean, then rinse with water.

 CAUTION: Do not use oven cleaner, abrasive cleansers

(kitchen cleansers), cleaners that contain citrus products, or

abrasive cleaning pads on barbecue or cart surfaces.

GENERAL INSTRUCTIONS

 WARNING: Check the bottom tray for grease build-up before

each use. Remove excess grease to avoid a grease fire in the

slide out bottom tray.

9

WWW.WEBER.COM

®

9

GENERAL INSTRUCTIONS

Slide out Bottom tray - Remove excess grease, then wash with warm soapy water,

then rinse.

Flavorizer

®

bars and Cooking grates - Clean with a suitable brass bristle brush. As

needed, remove from grill and wash with warm soapy water, then rinse with water.

Catch pan - Disposable foil trays are available, or you can line the catch pan with

aluminum foil. To clean the catch pan, wash with warm soapy water, then rinse.

Thermometer - Wipe with warm soapy water; clean with plastic scrub ball.

Inside cooking module - Brush any debris off of burner tubes. DO NOT ENLARGE

BURNER PORTS (OPENINGS). Wash inside of cooking box with warm soapy water

and a water rinse.

Inside Lid - While lid is warm, wipe inside with paper towel to prevent grease build-up.

Flaking built-up grease resembles paint flakes.

Stainless steel surfaces - Wash with a soft cloth and a soap and water solution. Be

careful to scrub with the grain direction of the stainless steel.

Do not use cleaners that contain acid, mineral spirits or xylene. Rinse well after

cleaning.

Preserve Your Stainless Steel - Your grill or its cabinet, lid, control panel and shelves

may be made from stainless steel. To keep the stainless steel looking its best is a

simple matter. Clean it with soap and water, rinse with clear water and wipe dry. For

stubborn particles, the use of a non-metallic brush can be used.

 IMPORTANT: Do not use a wire brush or abrasive cleaners

on the stainless steel surfaces of your grill as this will cause

scratches.

 IMPORTANT: When cleaning surfaces be sure to rub/wipe

in the direction of the grain to preserve the look of your

stainless steel.

IMPORTANT LP CYLINDER INFORMATION

Failure to follow these DANGER statements exactly may result in a fire causing death or

serious injury.

 DANGER

 NEVER store a spare LP Cylinder under or near this

barbecue.

 NEVER fill the tank beyond 80% full.

The proper filling methods for the filling of your cylinder are by weight or volume, as

described in NFPA 58. Please make sure your filling station fills your LP cylinder by

weight or volume. Ask your filling station to read purging and filling instructions on the

LP cylinder before attempting to fill.

LEAK CHECK PREPARATION

CHECK THAT ALL BURNER VALVES ARE OFF

Valves are shipped in the “OFF” position, but you should check to be sure that they are

turned off. Check by pushing down and turning clockwise. If they do not turn, they are

off. Proceed to the next step. If they do turn continue turning them clockwise until they

stop, then they are off. Proceed to the next step.

Your Weber

®

gas grill is equipped for a cylinder supply system designed for

vapor withdrawal.

 WARNING: Only use this grill outdoors in a well-ventilated

area. Do not use in a garage, building, breezeway or any

other enclosed area.

GAS INSTRUCTIONS

CONNECTING THE LIQUID PROPANE CYLINDER

All Weber

®

liquid propane gas grill regulators are equipped with a UL-listed tank

connection as per the latest edition of ANSI Z21.58. This will require a liquid propane

tank that is similarly equipped with a Type 1 connection in the tank valve. This Type 1

coupling allows you to make a fast and totally safe hookup between your gas grill and

your liquid propane tank. It eliminates the chance of leaks due to a POL fitting that is

not properly tightened. Gas will not flow from the tank unless the Type 1 coupling is fully

engaged into the coupling.

 WARNING: Make sure that the LP cylinder valve is closed.

Close by turning valve clockwise.

 DANGER

Do not use an open flame to check for gas leaks. Be sure

there are no sparks or open flames in the area while you

check for leaks. Sparks or flames will result in a fire or

explosion which can cause serious bodily injury or death,

and damage to property.

TYPE 1 CONNECTIVE COUPLING

1 Type 1 Valve

2 Hand Wheel

3 External Thread

4 Thermally Sensitive Nut

5 Propane Regulator

10

WWW.WEBER.COM

®

GAS INSTRUCTIONS

To connect the hose to the cylinder:

1) Pass the regulator hose through the side panel opening to the inside of the base

cabinet.

2) Locate hose retention clip (a) on regulator hose. Secure into slot (b) on underside

of tank scale.

 WARNING: The hose must be secured to the tank scale

with the Hose Retention Clip. Failure to do so could cause

damage to the hose resulting in a fire or explosion which

can cause serious bodily injury or death, and damage to

property.

7) Remove the plastic dust cover from the valve.

8) Screw the regulator coupling onto the tank valve, clockwise, or to the right. Hand-

tighten only.

Note: This is a new type of connection. It tightens clockwise and will not allow gas to

flow unless the connection is tight. The connection requires tightening by hand only.

 WARNING: Do not use a wrench to tighten the connection.

Using a wrench could damage the regulator coupling and

could cause a leak.

You will need: LP cylinder, a soap and water solution and a rag or brush to apply it.

9) Mix soap and water.

10) Turn on the cylinder valve.

11) Check for leaks by wetting the fitting with the soap and water solution and

watching for bubbles. If bubbles form, or if a bubble grows, there is a leak.

If there is a leak, turn off the gas and tighten the fitting. Turn the gas back on and

recheck with the soap and water solution.

If leak does not stop, contact the Customer Service Representative in your area using

the contact information on our web site. Log onto www.weber.com®. Do not use the

barbecue.

12) When leak checking is complete, turn gas supply OFF at the source and rinse

connections with water.

GAS INSTRUCTIONS

The LP cylinder is installed inside the base cabinet, on the tank scale (right side).

3) Open base cabinet doors.

4) Turn the LP cylinder so the opening of the valve is either to the front, side or rear

of the Weber

®

gas barbecue. Lift and hook the cylinder onto the fuel gauge.

5) Lift tank up into position on the tank scale.

6) Loosen the cylinder lock wing nut. Swing the cylinder lock down. Tighten the wing

nut.

Some LP tanks have differing top collar assembles. (The top collar is the metal

protective ring around the valve.) One series of tanks mount with the valve facing front

(a). The other tanks mount with the valve facing away from the fuel scale (b). Weber

recommends the use of cylinder manufacturer’s Manchester and Worthington, with a

47.6 lb water capacity. Other cylinders may be acceptable for use with the appliance

provided they are compatible with the appliance retention means (see illustrations).

11

WWW.WEBER.COM

®

11

GAS INSTRUCTIONS

REMOVE CONTROL KNOBS & CONTROL PANEL FOR LEAK

TESTING

You will need: Phillips screwdriver.

1) Remove control knobs.

2) Remove screw and washer from back of control panel with a Phillips screwdriver.

3) Tilt the back edge of the control panel up. Push in on the front edge to release

locking tabs. Carefully pull control panel away from frame.

4) Disconnect the igniter wires from the ignition module.

5) Replace control panel when Leak Check is completed.

GAS INSTRUCTIONS

1

2

3

4

CHECK FOR GAS LEAKS

 WARNING: You should check for gas leaks every time you

disconnect and reconnect a gas fitting.

Note: All factory-made connections have been thoroughly checked for gas leaks. The

burners have been flame-tested. As a safety precaution however, you should recheck

all fittings for leaks before using your Weber

®

Gas Barbecue. Shipping and handling

may loosen or damage a gas fitting.

 WARNING: Perform these leak checks even if your barbecue

was dealer or store assembled.

You will need: a soap and water solution, and a rag or brush to apply it.

Note: Since some leak test solutions, including soap and water, may be slightly

corrosive, all connections should be rinsed with water after checking for leaks.

If your grill has a side burner make sure the side burner is off.

To perform leak checks: open cylinder valve by turning the cylinder valve hand-wheel

counterclockwise.

 WARNING: Do not ignite burners when leak checking.

Check for leaks by wetting the connections with the soap and water solution and

watching for bubbles. If bubbles form or if a bubble grows, there is a leak.

 DANGER

Do not use an open flame to check for gas leaks. Be sure

there are no sparks or open flames in the area while you

check for leaks. Sparks or open flames will result in a fire or

explosion, which can cause serious bodily injury or death

and damage to property.

Check:

1) Hose-to-manifold connection.

 WARNING: If there is a leak at connection (1), retighten the

fitting with a wrench and recheck for leaks with soap and

water solution. If a leak persists after retightening the fitting,

turn OFF the gas. DO NOT OPERATE THE GRILL. Contact

the Customer Service Representative in your area using the

contact information on our web site.

Log onto www.weber.com

®

.

2) Regulator-to-cylinder connection.

3) The hose-to-regulator connection.

4) Valves-to-manifold connections.

 WARNING: If there is a leak at connections (2), (3) or (4),

turn OFF the gas. DO NOT OPERATE THE GRILL. Contact

the Customer Service Representative in your area using the

contact information on our web site.

Log onto www.weber.com

®

.

When leak checks are complete, turn gas supply OFF at the source and rinse

connections with water.

* The grill illustrated may have

slight differences than the

model purchased.

310

12

WWW.WEBER.COM

®

GAS INSTRUCTIONS

Check:

1) Hose to manifold connection.

2) Side burner hose to manifold connection and side burner hose to side burner gas

line connection.

3) Side burner hose to side burner connection, side burner valve and orifice

connections.

 WARNING: If there is a leak at connection (1, 2, or 3),

retighten the fitting with a wrench and recheck for leaks with

soap and water solution. If a leak persists after re-tightening

the fitting, turn OFF the gas. DO NOT OPERATE THE GRILL.

Contact the Customer Service Representative in your area

using the contact information on our web site.

Log onto www.weber.com

®

.

4) Regulator to cylinder connection.

5) Hose to regulator connection.

6) Valves to manifold connections.

 WARNING: If there is a leak at connections (4, 5 or 6), turn

OFF the gas. DO NOT OPERATE THE GRILL. Contact the

Customer Service Representative in your area using the

contact information on our web site.

Log onto www.weber.com

®

.

When leak checks are complete, turn gas supply OFF at the source and rinse

connections with water.

REFILLING THE LIQUID PROPANE CYLINDER

We recommend that you refill the LP cylinder before it is completely empty.

Removal of the LP cylinder

1) Close cylinder valve (turn clockwise).

2) Unscrew regulator coupling by turning counterclockwise, by hand only.

3) Loosen cylinder lock wing nut and turn cylinder lock up out of the way.

4) Lift cylinder off.

To fill, take the LP cylinder to a gas propane dealer, or look up “gas-propane” in the

phone book for other sources of LP gas.

 WARNING: We recommend that your LP cylinder be filled

at an authorized LP gas dealer, by a qualified attendant,

who fills the cylinder by weight. IMPROPER FILLING IS

DANGEROUS.

 CAUTION: Place dust cap on cylinder valve outlet whenever

the cylinder is not in use. Only install the type of dust cap

on the cylinder valve outlet that is provided with the cylinder

valve. Other types of caps or plugs may result in leakage of

propane.

CHECKING THE FUEL LEVEL IN YOUR TANK

Check the fuel level by viewing the color indicator level line on the side of the tank scale.

1) Empty

2) Medium

3) Full

GAS INSTRUCTIONS

* The grill illustrated may have

slight differences than the

model purchased.

320

13

WWW.WEBER.COM

®

13

SAFE HANDLING TIPS FOR LIQUID PROPANE GAS

CYLINDERS

• Liquid Propane (LP) gas is a petroleum product as are gasoline and natural gas.

LP gas is a gas at regular temperatures and pressures. Under moderate pressure,

inside a cylinder, LP gas is a liquid. As the pressure is released, the liquid readily

vaporizes and becomes gas.

• LP gas has an odor similar to natural gas. You should be aware of this odor.

• LP gas is heavier than air. Leaking LP gas may collect in low areas and prevent

dispersion.

• To fill, take the LP cylinder to a gas propane dealer, or look up “gas-propane” in

the phone book for other sources of LP gas.

 WARNING: We recommend that your LP cylinder be filled

at an authorized LP gas dealer, by a qualified attendant,

who fills the tank by weight. IMPROPER FILLING IS

DANGEROUS.

• Air must be removed from a new LP cylinder before the initial filling. Your LP

dealer is equipped to do this.

• The LP cylinder must be installed, transported and stored in an upright position.

LP cylinders should not be dropped or handled roughly.

• Never store or transport the LP cylinder where temperatures can reach 125° F

(too hot to hold by hand - for example: do not leave the LP cylinder in a car on a

hot day).

Note: A refill will last about 18-20 hours of cooking time at normal use. The fuel scale

will indicate the propane supply so you can refill before running out. You do not have

to run out before you refill.

• Treat “empty” LP cylinders with the same care as when full. Even when the LP

tank is empty of liquid there still may be gas pressure in the cylinder. Always

close the cylinder valve before disconnecting.

 CAUTION: Place dust cap on cylinder valve outlet whenever

the cylinder is not in use. Only install the type of dust cap

on the cylinder valve outlet that is provided with the cylinder

valve. Other types of caps or plugs may result in leakage of

propane.

• Do not use a damaged LP cylinder. Dented or rusty LP cylinders or LP cylinders

with a damaged valve may be hazardous and should be replaced with a new one

immediately.

Liquid Propane (LP) Cylinder(s)

• The joint where the hose connects to the LP cylinder must be leak tested each

time the LP cylinder is reconnected. For example, test each time the LP cylinder is

refilled.

• Be sure the regulator is mounted with the small vent hole pointed downward so

that it will not collect water. This vent should be free of dirt, grease, bugs etc.

• The gas connections supplied with your Weber

®

gas barbecue have been

designed and tested to meet 100% CSA and ANSI requirements.

 WARNING: Replacement LP tanks must match the

regulator connection supplied with this barbecue.

LIQUID PROPANE CYLINDER REQUIREMENTS

• Check to be sure cylinders have a D.O.T. certification (1), and date tested (2)

is within five years. Your LP gas supplier can do this for you.

• All LP tank supply systems must include a collar to protect the cylinder valve.

• The LP cylinder must be a 20-lb. size approximately (18¼ inches high, 12¼

inches in diameter).

• The cylinder must be constructed and marked in accordance with

the Specifications for LP - Gas Cylinders of the U.S. Department of

Transportation (D.O.T.) or the National Standard of Canada, CAN/CSA-B339,

Cylinders, Spheres and Tubes or Transportation of Dangerous Goods; and

Commission, as applicable.

IN CANADA

LIQUID PROPANE CYLINDER REQUIREMENTS

Note: Your retailer can help you match a replacement tank to your barbecue.

• The LP cylinder must be constructed and marked in accordance with the

specifications for LP gas cylinders, T.C.

DOT 4BA240

00/07

2

1

GAS INSTRUCTIONS

LIGHTING

Summary lighting instructions are inside the left hand cabinet door.

 DANGER

Failure to open the lid while igniting the barbecue’s burners,

or not waiting 5 minutes to allow the gas to clear if the

barbecue does not light, may result in an explosive flame-up

which can cause serious bodily injury or death.

CROSSOVER

®

IGNITION SYSTEM

Note: The Crossover

®

Ignition System ignites BURNER 1 with a spark from the igniter

electrode inside the Gas Catcher

™

ignition chamber. You generate the energy for the

spark by pushing the electronic ignition button. You will hear it sparking.

 WARNING: Check hose before each use of barbecue for nicks,

cracking, abrasions or cuts. If the hose is found to be damaged

in any way, do not use the barbecue. Replace using only Weber

®

authorized replacement hose. Contact the Customer Service

Representative in your area using the contact information on

our web site. Log onto www.weber.com

®

.

OPERATING INSTRUCTIONS

14

WWW.WEBER.COM

®

MAIN BURNER LIGHTING

1) Open the lid.

2) Make sure all burner control knobs are turned OFF. (Push control knob down and

turn clockwise to ensure that it is in the OFF position.)

 WARNING: The burner control knobs must be in the OFF

position before turning on the liquid propane cylinder tank

valve. If they are not in the OFF position, when you turn on

the LP cylinder valve, the “excess gas flow control” feature

will activate, limiting the flow of gas from the LP cylinder. If

this should occur, turn OFF the LP cylinder valve and burner

control knobs. Start over.

 DANGER

When the “excess gas flow control” feature is activated,

a small amount of gas is still flowing to the burners. After

turning OFF the cylinder valve, wait at least 5 minutes for the

gas to clear before attempting to light the barbecue. Failure to

do so may result in an explosive flame-up, which can cause

serious bodily injury or death.

3) Turn the cylinder on by slowly turning the cylinder valve counterclockwise.

 WARNING: Do not lean over the open barbecue. Keep your

face and body at least one foot away from the matchlight

hole when lighting the barbecue.

4) Push BURNER 1 control knob down and turn to START/HI.

5) Push and hold the electronic ignition button. You will hear it sparking.

6) Check that the burner is lit by looking through the matchlight hole on the front of

the cooking box. You should see a flame.

 WARNING: If the burner does not light in five (5) seconds,

turn the Burner 1 control knob to OFF and wait 5 minutes

to let the gas clear before you try again or try to light with a

match.

7) After BURNER 1 is lit you can turn on BURNER 2 and BURNER 3.

Note - Always light BURNER 1 first. The other burners ignite from BURNER 1.

TO EXTINGUISH

Push down and turn each burner control knob clockwise to the OFF position. Turn gas

supply OFF at the source.

OPERATING INSTRUCTIONS

6

3

1

4

5

7

2

* The grill illustrated may have

slight differences than the

model purchased.

6

3

1

5

4

7

2

* The grill illustrated may have

slight differences than the

model purchased.

MAIN BURNER MANUAL LIGHTING

 DANGER

Failure to open the lid while igniting the barbecue’s burners, or

not waiting 5 minutes to allow the gas to clear if the barbecue

does not light, may result in an explosive flame-up which can

cause serious bodily injury or death.

1) Open the lid.

2) Make sure all burner control knobs are turned OFF. (Push each knob down and

turn clockwise to ensure they are in the “OFF” position.)

 WARNING: The burner control knobs must be in the OFF

position before turning on the liquid propane cylinder valve.

If they are not in the OFF position, when you turn on the

LP cylinder valve, the “excess gas flow control” feature will

activate, limiting the flow of gas from the LP cylinder. If this

should occur, turn OFF the LP tank valve and burner control

knobs. Start over.

MAIN BURNER LIGHTING

MAIN BURNER MANUAL LIGHTING

1

O

F

A

R

E

T

E

/

A

P

A

G

A

D

O

2

5

15

WWW.WEBER.COM

®

15

OPERATING INSTRUCTIONS

 DANGER

When the “excess gas flow control” feature is activated,

a small amount of gas is still flowing to the burners. After

turning OFF the cylinder and burner control knobs, wait at

least 5 minutes for the gas to clear before attempting to light

the barbecue. Failure to do so may result in an explosive

flame-up, which can cause serious bodily injury or death.

3) Turn the cylinder on by turning the cylinder valve counterclockwise.

4) Insert match holder with lit match into the matchlight hole in the front of the

cooking box.

 WARNING: Do not lean over open barbecue. Keep your face

and body at least one foot away from the matchlight hole

when lighting the barbecue.

5) Push BURNER 1 control knob down and turn to START/HI.

6) Check that the burner is lit by looking through the matchlight hole on the front of

the cooking box. You should see a flame.

 WARNING: If the burner does not light in five seconds, turn

the Burner 1 control knob to OFF and wait 5 minutes to let

the gas clear before you try again.

7) After BURNER 1 is lit you can turn on BURNER 2 and BURNER 3.

Note - Always light BURNER 1 first. The other burners ignite from BURNER 1.

TO EXTINGUISH

Push down and turn each burner control knob clockwise to the OFF position. Turn gas

supply OFF at the source.

6

3

1

5

4

7

2

MAIN BURNER MANUAL LIGHTING

OPERATING INSTRUCTIONS

* The grill illustrated may have

slight differences than the

model purchased.

LIGHTING THE SIDE BURNER

 DANGER

Failure to open the lid while igniting the side burner, or not

waiting 5 minutes to allow the gas to clear if the side burner

does not light, may result in an explosive flame-up which can

cause serious bodily injury or death.

 WARNING: Check hose before each use of barbecue for nicks,

cracking, abrasions or cuts. If the hose is found to be damaged

in any way, do not use the barbecue. Replace using only Weber

®

authorized replacement hose. Contact the Customer Service

Representative in your area using the contact information on

our web site. Log onto www.weber.com

®

.

1) Open the side burner lid.

2) Check that the side burner valve is turned off (Push control knob in and turn

clockwise to ensure that it is in the “OFF” position), turn all burners not being used

to the “OFF” position (push in and turn clockwise).

3) Turn the gas supply valve on.

4) Push down and turn the side burner control valve to “HI”.

5) Press the igniter button several times so it clicks each time.

 CAUTION: Side burner flame may be difficult to see on a

bright sunny day.

 WARNING: If the side burner does not light in five (5)

seconds:

a) Turn off the side burner control valve, main burners

and gas supply at source.

b) Wait 5 minutes to let the gas clear before you try

again, or try lighting with a match (see “Manually

Lighting the Side Burner”).

320

1

O

F

A

R

E

T

E

/

A

P

A

G

A

D

O

2

5

16

WWW.WEBER.COM

®

MANUALLY LIGHTING THE SIDE BURNER

 DANGER

Failure to open the lid while igniting the side burner, or not

waiting 5 minutes to allow the gas to clear if the side burner

does not light, may result in an explosive flare-up that can

cause serious bodily injury or death.

1) Open the side burner lid.

2) Check that the side burner valve is turned off (Push control knob in and turn

clockwise to ensure that it is in the “OFF” position), turn all burners not being used

to the “OFF” position (push in and turn clockwise).

3) Turn the gas supply valve on.

4) Put match in a match holder and strike match.

5) Hold match holder and lit match by either side of the side burner.

6) Push down and turn the side burner control valve to “HI”.

 CAUTION: Side burner flame may be difficult to see on a

bright sunny day.

 WARNING: If the side burner does not light in five (5)

seconds:

a) Turn off the side burner control valve, main burners

and gas supply at source.

b) Wait 5 minutes to let the gas clear before you try

again.

OPERATING INSTRUCTIONS

TROUBLESHOOTING

PROBLEM CHECK CURE

Burners burn with a yellow or orange flame, in

conjunction with the smell of gas.

Inspect Spider/Insect Screens for possible obstructions.

(Blockage of holes.)

Clean Spider/Insect Screens. (See Section “Annual

Maintenance”)

Symptoms:

Burners do not light. -or- Burners have a small

flickering flame in the “HI” position. -or-

Barbecue temperature only reaches 250˚ to 300˚

in the “HI” position.

The excess flow safety device, which is part of the

barbecue to cylinder connection, may have activated.

To reset the excess flow safety device turn all burner control

knobs and the cylinder valve off. Disconnect the regulator

from the cylinder. Turn burner control knobs to “HI”. Wait at

least 1 minute. Turn burner control knobs to “OFF”. Reconnect

the regulator to the cylinder. Turn cylinder valve on slowly.

Refer to “Lighting Instructions”.

Burner does not light, or flame is low in “HI”

position.

Is LP fuel low or empty? Refill LP cylinder.

Is fuel hose bent or kinked? Straighten fuel hose.

Does Burner 1 light with a match? If you can light Burner 1 with a match, then check the

Crossover

®

ignition system.

Experiencing flare-ups:

 CAUTION: Do not line the bottom tray

with aluminum foil.

Are you preheating barbecue in the prescribed manner? All burners on HI for 10 to 15 minutes for preheating.

Are the cooking grates and Flavorizer

®

bars heavily

coated with burned-on grease?

Clean thoroughly. (See Section “Cleaning”)

Is the bottom tray “dirty” and not allowing grease to flow

into catch pan?

Clean bottom tray.

Burner flame pattern is erratic. Flame is low when

burner is on “HI”. Flames do not run the whole

length of the burner tube.

Are burners clean? Clean burners. (See Section “Maintenance”.)

Inside of lid appears to be “peeling.” (Resembles

paint peeling.)

The lid is porcelain enamel or stainless steel, not paint.

It cannot “peel”. What you are seeing is baked on grease

that has turned to carbon and is flaking off.

THIS IS NOT A DEFECT.

Clean thoroughly. (See Section “Cleaning”.)

Cabinet doors are not aligned. Check the adjustment pin on the bottom of each door. Loosen adjustment nut/s. Slide door/s until aligned. Tighten

nut.

If problems cannot be corrected by using these methods, please contact the Customer Service Representative in your area using the contact information on our web

site. Log onto www.weber.com

®

.

320

17

WWW.WEBER.COM

®

17

PROBLEM CHECK CURE

Side Burner does not light. Is gas supply off?

The excess flow safety device, which is part

of the barbecue to cylinder connection, may

have activated.

Turn supply on.

To reset the excess flow safety device turn all burner control knobs and the cylinder

valve off. Disconnect the regulator from the cylinder. Turn burner control knobs to

START/HI. Wait at least 1 minute. Turn burner control knobs to “OFF”. Reconnect

the regulator to the cylinder. Turn cylinder valve on slowly. Refer to “Lighting

Instructions”.

Flame is low in “HI” position. Is the fuel hose bent or kinked? Straighten hose.

Push button ignition does not work. Does burner light with a match? If match lights burner, check igniter (see Sideburner Maintenance).

If problems cannot be corrected by using these methods, please contact the Customer Service Representative in your area using the contact information on our

web site. Log onto www.weber.com

®

.

WEBER

®

SPIDER/INSECT SCREENS

Your Weber

®

gas barbecue, as well as any outdoor gas appliance, is a target for spiders

and other insects. They can nest in the venturi section (1) of the burner tubes. This

blocks the normal gas flow, and can cause the gas to flow back out of the combustion

air opening. This could result in a fire in and around the combustion air openings, under

the control panel, causing serious damage to your barbecue.

The burner tube combustion air opening is fitted with a stainless steel screen (2) to

prevent spiders and other insects access to the burner tubes through the combustion air

openings.

We recommend that you inspect the Spider/Insect screens at least once a year.

(See Section “Annual Maintenance”.) Also inspect and clean the the Spider/Insect

screens if any of the following symptoms should ever occur:

1) The smell of gas in conjunction with the burner flames appearing yellow and lazy.

2) Barbecue does not reach temperature.

3) Barbecue heats unevenly.

4) One or more of the burners do not ignite.

 DANGER

Failure to correct the above mentioned symptoms may result

in a fire, which can cause serious bodily injury or death, and

cause damage to property.

Side Burner Grate

Side Burner cap

Side Burner Ring & Head

Igniter Electrode

Control Knob

Igniter

SIDE BURNER TROUBLESHOOTING

SIDE BURNER MAINTENANCE

MAINTENANCE

SIDE BURNER MAINTENANCE

 WARNING: All gas controls and supply valves should be in

the “OFF” position.

Make sure black wire is connected between the igniter and electrode.

Make sure white wire is connected between the igniter and grounding clip.

Spark should be a white/blue color, not yellow.

1) Igniter Wire

2) Ground wire

3) Burner

18

WWW.WEBER.COM

®

ANNUAL MAINTENANCE

INSPECTION AND CLEANING OF THE SPIDER/INSECT SCREENS

To inspect the Spider/Insect screens, remove the control panel. If there is dust or dirt on the screens, remove the burners for cleaning the screens.

Brush the Spider/Insect screens lightly with a soft bristle brush (i.e. an old toothbrush).

 CAUTION: Do not clean the Spider/Insect screens with hard or sharp tools. Do not dislodge the Spider/Insect screens or

enlarge the screen openings.

Lightly tap the burner to get debris and dirt out of the burner tube. Once the Spider/Insect screens and burners are clean replace the burners.

If the Spider/Insect screen becomes damaged or cannot be cleaned, please contact the Customer Service Representative in your area using the contact information on our web

site. Log onto www.weber.com

®

.

BURNER FLAME PATTERN

The Weber

®

gas barbecue burners have been factory set for the correct air and gas

mixture. The correct flame pattern is shown.

1) Burner tube

2) Tips occasionally flicker yellow

3) Light blue

4) Dark blue

If the flames do not appear to be uniform throughout the burner tube, follow the burner

cleaning procedures.

MAIN BURNER CLEANING PROCEDURE

Turn off the gas supply.

Remove the manifold (See “Replace Main Burners”).

Look inside each burner with a flashlight.

Clean the inside of the burners with a wire (a straightened-out coat hanger will work).

Check and clean the air shutter opening at the ends of the burners. Check and clean

the valve orifices at the base of the valves. Use a Steel bristle brush to clean outside of

burners. This is to make sure all the burner ports are fully open.

 CAUTION: Do not enlarge the burner ports when cleaning.

a

b

c

d

e

REPLACING MAIN BURNERS

1) Your Weber

®

gas barbecue must be OFF and cool.

2) Turn gas OFF at source.

3) To remove control panel:

(a) Take off the burner control knobs.

(b) Remove screw and washer from back of control panel with a Phillips screwdriver.

(c) Tilt the back edge of the control panel up. Push in on the front edge to release

locking tabs.

(d) Disconnect the igniter wires from the ignition module.

(e) Carefully pull control panel away from frame.

MAINTENANCE

19

WWW.WEBER.COM

®

19

CROSSOVER

®

IGNITION SYSTEM OPERATIONS

If The Crossover

®

Ignition System fails to ignite the BURNER 1, light BURNER 1 with a

match. If BURNER 1 lights with a match, then check the Electronic Ignition System.

• Check that both of the ignition wires are attached at the igniter module properly.

• Check that the ignition wire is attached at the ceramic igniter properly.

• Check that the ceramic igniter assembly (A) is fully positioned into burner tube 1

igniter channel (B).

• Check that the ceramic igniter is properly positioned over the burner holes on

BURNER 1.

• Check that the Electronic Ignition Button is working by listening and looking for

sparks at BURNER 1.

REPLACE BATTERY IF NECESSARY

AAA alkaline battery only. See illustration:

If the Electronic Ignition System still fails to light, contact the Customer Service

Representative in your area using the contact information on our web site. Log

onto www.weber.com

®

.

4) Remove the two threaded 7/16” hex screws (a) that hold the manifold support

bracket to the cooking box. Pull the manifold and valve assembly towards you, at

the same time lift the manifold assembly up to release the manifold brackets from

the frame assembly. (b).

5) Slide the burner assembly out from under the guide screw and washer (a) in the

corners of the cooking box.

6) Lift and twist the burner assembly slightly, to separate the crossover tube (b) from

the burners. Remove the burners from the cooking box.

7) To reinstall the burners, reverse 3) through 7).

 CAUTION: The burner openings (c) must be positioned

properly over the valve orifices (d).

Check proper assembly before fastening manifold in place.

 WARNING: After reinstalling the gas lines, they should be

leak checked with a soap and water solution before using the

barbecue. (See Step: “Check for gas leaks.”)

MAINTENANCE

A

B

BARBACOA DE GAS

#00000

#89555

Guía del Propietario de la barbacoa de

gas propano licuado

E/S-310/320, EP-310/320

89555 ESNA

DEBE LEER ESTA GUÍA DEL PROPIETARIO

ANTES DE PONER A FUNCIONAR LA

BARBACOA DE GAS

 PELIGRO

Si huele a gas:

1. Cierre el suministro de gas al artefacto.

2. Apague todas las flamas cerrando la valvula

general de paso.

3. Abra la tapa.

4. Llame inmediatamente a la central de fugas

o a su proveedor de gas.

Una fuga de gas puede provocar un incendio

o explosión que puede resultar en lesiones

corporales serias o la muerte, o daños a la

propiedad.

 PARA SU SEGURIDAD:

1. No almacene gasolina u otros fluidos

flamables en la cercanía de su aparato.

2. Ningún cilindro de propano licuado que

no esté conectado para su uso deberá

almacenarse cerca de éste o cualquier otro

artefacto doméstico.

 NOTA IMPORTANTE: Antes de

poner a funcionar la asador,

siga cuidadosamente todos los

procedimientos en este manual para

verificar que no existan fugas. Haga

esto aun y cuando la asador haya sido

ensamblada por el distribuidor.

AVISO AL INSTALADOR:

Estas instrucciones deben permanecer con

el propietario, quien las deberá guardar

para un futuro uso.

ESTE ARTEFACTO A GAS ESTÁ DISEÑADO

PARA USARSE SOLAMENTE AL AIRE

LIBRE.

 NOTA IMPORTANTE: No trate de

encender este artefacto sin antes leer la

sección “Instrucciones para encender la

asador” de este manual.

La page charge ...

Genesis S-320 Le manuel du propriétaire

Ce manuel convient également à

Genesis S-320 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents