L'Or Barista LM8012/60 Manuel utilisateur

Catégorie
Accessoires de préparation de café
Taper
Manuel utilisateur

Ce manuel convient également à

6
5
2
1
3
13
9
11 10
8
12
7
4
15
14
16
English 7
Deutsch 22
Español 38
Français 54
Italiano 70
Nederlands 86
Português 102
English
Machine overview
1 On/off button
2 Ristretto button
3 Espresso button
4 Lungo button
5 Water tank lid
6 Water tank
7 Mains cord with plug
8 Used capsule drawer
9 Waste water drawer
10 Lower drip tray
11 Drip tray
12 Cup platform
13 Coffee outlets
14 Coffee dispensing spout cap
15 Capsule compartment
16 Lever
Introduction
Welcome to the L'OR Barista world! The L'OR Barista coffee system is the
only capsule coffee system that allows you to brew two cups of coffee at the
same time thanks to a coffee dispensing spout with double outlet.
The new and exclusive L'OR Barista double-shot coffee capsules allow you
to brew two cups of coffee or a double shot of coffee.
The L'OR Barista coffee machine is also compatible with the L'OR Espresso
single-shot coffee capsules. Thanks to the Dual Capsule Recognition
technology, the machine automatically recognizes the capsule size and
adapts the volume accordingly. All you need to do is press the button for
the type of coffee you desire.
Capsule compatibility
The L'OR Barista coffee machine has been designed to work with L’OR
Espresso single-shot capsules and L’OR Barista double-shot capsules, as
well as with Nespresso* capsules and aluminum capsules from coffee
brands produced by Jacobs Douwe Egberts, such as Douwe Egberts,
JACOBS, Jacqmotte, Jacques Vabre, Grand Mère, L'OR, Marcilla, Moccona,
Saimaza and Senseo.
*brand of a third party not connected to JACOBS DOUWE EGBERTS and / or
PHILIPS
Preparing for use
Before first use, remove all packaging materials from the machine.
When you use the machine for the first time or if you have not used it for 1
day or longer, perform the following steps:
7
English
1 Remove the water tank from the machine.
2 Rinse and fill the water tank under the tap. Place the water tank back
onto the machine.
3 Place a bowl under the coffee dispensing spout. Do not insert a capsule
and make sure that the lever is closed.
25 sec
°C
4 Press the on/off button to switch on the machine.
-
The on/off button flashes slowly to indicate that the machine is
heating up.
5 When all buttons light up continuously, press the lungo button.
-
Water flows from the coffee dispensing spout.
Note: When the internal water circuit is empty, the machine produces a
humming sound. When the machine dispenses water, it produces a less
loud humming sound. This is normal.
6 The machine is ready when all buttons light up continuously.
7 Empty the drip tray and waste water drawer (see 'Cleaning the used
capsule drawer and waste water drawer').
The machine is now ready for use.
8
English
Brewing coffee
Beverages and capsules
Capsules
L’OR aluminum capsules are available online at www.lorespresso.com and in
shops. You can choose from a variety of coffee capsules for different types
of coffee.
Beverages
Thanks to the Dual Capsule Recognition technology, the machine
automatically recognizes the capsule size and adapts the volume of your
drink accordingly. All you need to do is press the button for the type of
coffee you desire.
25 ml
Ristretto
2x 25 ml
50 ml
Double ristretto / Double shot of ristretto
40 ml
Espresso
2x 40 ml
80 ml
Double espresso / Double shot of espresso
9
English
110 ml
Lungo
2x 110 ml
220 ml
Double lungo / Double shot of lungo
220 ml
Grand Café Filtre
Preparing coffee
1 Press the on/off button to switch on the machine. The on/off button
starts flashing to indicate that the machine is heating up.
2 For one coffee, place one cup under the coffee dispensing spout.
3 For two coffees, place two cups under the coffee dispensing spout.
10
English
4 For a large coffee or Grand Café Filtre, remove the cup platform and the
drip tray, place the cup platform on the lower drip tray and place a large
cup or mug on the cup platform under the coffee dispensing spout.
5 Lift the lever.
6 Insert a capsule.
-
For a single cup of coffee, insert a L'OR Espresso single-shot capsule.
-
For two cups of coffee or one large coffee, insert a L'OR Barista
double-shot capsule.
7 Close the lever by pushing it down.
Warning: Do not insert a finger into the brew chamber when
closing the lever.
11
English
8 When the on/off button stops flashing and all buttons light up
continuously, press the button for the type of coffee you desire.
Caution: Do not lift the lever until the brewing process has finished.
Brewing is finished when the lights stop flashing and no more coffee
comes out of the coffee dispensing spout.
Brewing Grand Café Filtre
1 Remove the seal completely from the capsule.
2 Lift the lever and insert the capsule.
3 Close the lever.
4 Remove the drip tray with the cup platform. Put the drip tray aside and
place the cup platform on the lower drip tray.
12
English
5 Place a large cup or mug on the cup platform under the coffee
dispensing spout.
6 Press the lungo button to start the brewing process.
Adjusting the coffee quantity
Each coffee button has been programmed to brew coffee at its ideal setting.
Nevertheless, you can adapt the coffee quantity to your wishes, within a
range that ensures the best coffee quality.
L'OR Espresso single-shot
capsule
min standard max
Ristretto 20 ml 25 ml 40 ml
Espresso 30 ml 40 ml 50 ml
Lungo 85 ml 110 ml 135 ml
L'OR Barista double-shot
capsule
min standard max
Ristretto 40 ml 50 ml 60 ml
Espresso 60 ml 80 ml 100 ml
Lungo/Grand Café Filtre 170 ml 220 ml 270 ml
The coffee quantities for L'OR Espresso single-shot and L'OR Barista
double-shot capsules are adjusted separately:
1 Press the on/off button to switch on the machine.
2 Fill the water tank.
3 Insert a capsule and close the lever.
-
If you want to adjust the quantity for L'OR single-shot espresso
capsules, insert a normal L'OR Espresso capsule.
-
If you want to adjust the quantity for a L'OR Barista double-shot
capsule, insert a L'OR Barista capsule.
13
English
4 Press and hold the button of the coffee whose quantity you want to
adjust for 3 seconds until the button flashes quickly. Then release the
button. The machine starts brewing coffee.
5 Press the same button again when the cup contains the desired quantity
of coffee.
Note: If you press the coffee button too early, the machine programs the
minimum quantity of coffee shown in the table above. If you do not press
the coffee button, the machine programs the maximum quantity of
coffee.
Resetting the coffee quantities
To reset the coffee quantities to their factory settings:
1 Press the on/off button to switch on the machine.
2 Wait until the machine has heated up and all buttons light up.
3 Press and hold the ristretto, espresso and lungo buttons simultaneously
until all buttons flash quickly to show that the machine has been reset to
factory settings.
Cleaning and maintenance
Cleaning the used capsule drawer and waste water drawer
Check the used capsule drawer and waste water drawer regularly.
Note: For optimal hygiene, pull up the lever after use to ensure the last used
capsule falls into used capsule drawer.
1 Pull the used capsule drawer and the waste water drawer out of the
machine.
2 Remove the drip tray from the lower drip tray and rinse the drip tray and
the cup tray under a warm tap. Do not clean these parts in the
dishwasher.
14
English
3 Remove the used capsule drawer by pulling it up and empty it.
Caution: Be careful when you remove the used capsule drawer.
Capsules are still hot immediately after brewing.
4 Rinse all parts under a warm tap. Dry all parts with a soft cloth. You can
also clean all these parts in the dishwasher.
5 Reinsert the used capsule drawer into the waste water drawer.
6 Insert the waste water drawer with the used capsule drawer into the
machine.
7 Place the drip tray back onto the lower drip tray. Place the cup platform
onto the drip tray.
Cleaning other parts of the machine
1 Clean the outside of the machine with a soft damp cloth.
Caution: Never use scouring pads, abrasive cleaning agents or
aggressive liquids such as petrol or acetone to clean the machine.
Warning: Do not insert a finger into the capsule compartment
to avoid injury. There is an invisible piercer inside.
2 Clean the front of the machine with a soft damp cloth and clean the two
parts of the coffee dispensing spout (the coffee outlets and the spout
cover) under a warm tap or in the dishwasher.
3 Clean the water tank by rinsing it under a warm tap. The water tank is not
dishwasher-proof.
Note: Rinse the water tank and fill it with fresh water every 24 hours.
Cleaning the coffee circuit
Clean the coffee circuit every week to ensure you get coffee with an
optimum quality and taste.
15
English
1 Place a cup under the coffee dispensing spout.
2 Lift the lever to ensure the last used capsule falls into the used capsule
drawer.
3 Do not insert a new capsule and close the lever.
4 Press the lungo button.
5 Empty the cup after the machine has finished dispensing water.
6 Open the lever and repeat steps 3 to 5 to ensure proper cleaning of the
coffee circuit.
The machine is now ready for use.
Descaling
When to descale
-
Descale the machine when the ristretto and lungo button flash quickly a
few times after brewing. The descaling procedure takes up to 40 minutes
and consists of a descaling cycle and a rinsing cycle. Do not interrupt the
descaling procedure.
Why to descale
Descaling is essential for the following reasons:
-
It prolongs the life of your L'OR Barista coffee machine
-
It ensures maximum cup volume
-
It ensures maximum coffee temperature
16
English
-
The machine produces less sound during brewing
-
It prevents malfunctioning
If the descaling procedure is not performed correctly, scale residue remains
behind in the machine. This causes scale to build up more quickly and may
cause permanent and irreparable damage to the machine.
Use the correct descaler
Only citric acid-based descalers are suitable for descaling the L'OR Barista
machine. This type of descaler descales the machine without damaging it.
We advise you to use the dedicated L'OR Barista liquid descaler (CA6530). It
is available in bottles that contain liquid descaler for two descaling
procedures. You need half a bottle for one descaling procedure and can
store the other half for the next descaling procedure.
Descaling procedure
Note: If something goes wrong during the descaling procedure, e.g. because
you accidentally interrupt the descaling cycle, you have to restart the
descaling procedure from step 1.
1 Press the on/off button to switch on the machine.
2 Pour half a bottle of L'OR Barista liquid descaler (CA6530) into the water
tank.
3 Fill up the water tank with fresh tap water.
4 Make sure that there is no capsule in the capsule compartment.
17
English
5 Close the lever.
1.5L
6 Place a bowl with a minimum capacity of 1.5 liters on the lower drip tray
under the coffee dispensing spout to collect the descaling solution.
7 Press the ristretto and lungo button briefly at the same time.
8 The ristretto button starts to flash quickly. Press the ristretto button to
activate the descaling cycle.The machine dispenses the entire descaling
solution at regular intervals. This takes up to 30 minutes.
-
When the lungo button starts to flash quickly again, the first phase of
the descaling cycle has finished.
9 Remove and empty the bowl. Place the bowl back onto the lower drip
tray under the coffee dispensing spout.
10 Remove the water tank and rinse it under the tap. Fill the water tank with
cold tap water and place it back onto the machine.
18
English
11 Press the lungo button to start the flushing cycle.
Note: The water tank will be emptied without interruption. The flushing
cycle lasts about 3 minutes.
12 When the flushing cycle has finished, the ristretto and lungo button flash
a few times.
Note: It is normal that some water remains behind in the water tank after
the descaling procedure.
The machine switches off. The descaling procedure is finished.
Meaning of light signals
-
The on/off button flashes slowly: the machine is heating up.
-
The on/off button flashes quickly: the water tank is empty, fill the water
tank with tap water.
-
All buttons light up continuously: the machine is ready for use.
-
The selected coffee button flashes slowly: the machine is preparing the
coffee recipe.
-
The selected coffee button flashes quickly:
-
Programming is activated.
-
The new coffee quantity is saved.
-
The ristretto and lungo button flash simultaneously after brewing coffee:
you need to descale the machine.
Troubleshooting
This chapter summarizes the most common problems you could encounter
with your machine. If you are unable to solve the problem with the
information below, visit www.lorbarista.com/support for a list of frequently
asked questions or contact the Consumer Care Center in your country.
Problem
Possible cause Solution
The machine does not switch
on.
The machine is not connected to
the mains.
Put the plug in an earthed wall
socket.
The on/off button is flashing
slowly.
The machine is heating up. This is normal.
The brewing time is longer
than before.
The machine is clogging up with
scale.
Descale the machine (see
'Descaling procedure').
19
English
Problem Possible cause Solution
The temperature of freshly
brewed coffee gradually
decreases.
The machine is clogging up with
scale.
Descale the machine (see
'Descaling procedure').
The pump makes a lot of
noise.
There is not enough water in the
water tank.
Fill the water tank with fresh tap
water.
The water tank is not placed
correctly.
Place the water tank correctly
and push it downwards.
The machine suddenly stops
brewing coffee.
There is not enough water in the
water tank.
Fill the water tank with fresh tap
water. Press the button of the
selected type of coffee again to
continue brewing. When the cup
is full, press the same button
again to stop the brewing
process.
The on/off button flashes
quickly.
The water tank is empty. Fill the water tank with fresh tap
water. Press the button of the
selected type of coffee again to
continue brewing. When the cup
is full, press the same button
again to stop the brewing
process.
I cannot close the capsule
compartment lever
completely.
Check if you use the
recommended L'OR capsule. Other
capsules may cause problems
during use..
The used capsule drawer is full. Empty the used capsule drawer
and insert the capsule again.
The capsule is not inserted
correctly.
Insert the capsule again and
check if it is inserted correctly.
The capsule is stuck. Open and close the lever a few
times with moderate force to
remove the capsule.
The lever does not open
completely.
The used capsule drawer is full. Empty the used capsule drawer.
The machine does not
dispense coffee or only
dispenses drops of coffee.
You have not flushed the machine
before first use.
Flush the machine before first
use (see 'Preparing for use').
There is not enough water in the
water tank.
Fill the water tank with fresh tap
water.
Scale has built up inside the
machine (see 'Descaling').
Descale the machine (see
'Descaling').
20
English
Problem Possible cause Solution
Coffee grounds end up in the
cup of coffee.
A small amount of ground coffee
will always end up on the bottom
of the cup.
This is normal.
The coffee flow splits or is not
straight.
The coffee dispensing spout cap is
not placed correctly or it is missing.
Snap the coffee dispensing
spout onto the coffee outlets.
The ristretto and lungo button
lights are flashing after
brewing.
This means it is time to descale the
machine to prevent it from
clogging with scale.
Descale the machine (see
'Descaling').
Why do I find water in the
waste water drawer?
The used capsule drawer and
waste water drawer catch the
residual water released after
brewing coffee.
This is normal.
The coffee quantity is not
what I expected.
The coffee quantity has been
adjusted.
Readjust the coffee quantity (see
'Adjusting the coffee quantity') or
reset the coffee quantities (see
'Resetting the coffee quantities').
My coffee is less warm. When you brew the first cup of the
day or when it has been a while
since your previous cup of coffee,
the inside of the machine is still
cold when you brew coffee.
You can pre-heat the machine
and coffee cup by brewing a cup
of coffee first without placing a
coffee capsule.
If you use a cold, thick-walled cup,
the coffee will cool down
immediately.
Use thin-walled cups, as thin-
walled cups will absorb less heat
from the coffee than thick-
walled cups. Make sure the size
of the cup matches the coffee
quantity. Do not brew a small
quantity of coffee in a large cup.
The machine is clogged with scale. Descale the machine when the
ristretto and lungo button flash
quickly a few times after brewing
(see 'Descaling').
You used cold milk. If you drink coffee with cold,
fresh milk, this will cool down
your coffee. You can prevent this
by preheating the milk.
The machine suddenly
switches off after some time.
This is the automatic shut-off
function.
The automatic shut-off function
is programmed to switch off the
machine after 9 minutes of
inactivity to save energy.
21
English
Deutsch
Übersicht über die Maschine
1 Ein-/Ausschalter
2 Ristretto-Taste
3 Taste für Espresso
4 Lungo-Taste
5 Deckel des Wasserbehälters
6 Wasserbehälter
7 Netzkabel mit Stecker
8 Kapselauswurfschublade
9 Restwasserschublade
10 Untere Abtropfschale
11 Abtropfschale
12 Tassen-Plattform
13 Kaffeeausläufe
14 Deckel für Kaffeeauslauftrichter
15 Kapselfach
16 Hebel
Einführung
Willkommen in der Welt von L'OR Barista! Das L'OR Barista Kaffeesystem ist
das einzige Kapsel-Kaffeesystem, mit dem Sie zwei Tassen Kaffee
gleichzeitig zubereiten können - dank eines Kaffeeauslauftrichters mit
doppeltem Auslass.
Mit den neuen und exklusiven L'OR Barista Double-Shot-Kaffeekapseln
können Sie zwei Tassen Kaffee oder einen doppelten Kaffee zubereiten.
Die L'OR Barista Kaffeemaschine kann auch mit den L'OR Espresso Single-
Shot-Kaffeekapseln verwendet werden. Die Maschine erkennt automatisch
die Kapselgröße und passt die Menge entsprechend an. Sie brauchen nur
die Taste für die gewünschte Kaffeesorte zu drücken.
Geeignete Kapseln
Die L'OR Barista Kaffeemaschine eignet sich für die Kapselarten L’OR
Espresso Single-Shot und L’OR Barista Double-Shot. Verwendbar sind auch
Nespresso* Kapseln sowie Aluminiumkapseln der Kaffeemarken von Jacobs
Douwe Egberts, z.B. Douwe Egberts, JACOBS, Jacqmotte, Jacques Vabre,
Grand Mère, L'OR, Marcilla, Moccona, Saimaza und Senseo.
* Marke eines Drittanbieters, der nicht mit JACOBS DOUWE EGBERTS
und/oder PHILIPS verbunden ist
Für den Gebrauch vorbereiten
Entfernen Sie vor dem ersten Gebrauch sämtliche Verpackungsmaterialien
von der Maschine.
Wenn Sie die Maschine zum ersten Mal verwenden, oder wenn Sie sie für
einen Tag oder länger nicht verwendet haben, gehen Sie wie folgt vor:
22
Deutsch
1 Entfernen Sie den Wasserbehälter von der Maschine.
2 Spülen Sie den Wasserbehälter unter fließendem Wasser ab und befüllen
Sie ihn mit Leitungswasser. Setzen Sie den Wasserbehälter wieder auf die
Maschine auf.
3 Stellen Sie eine Schüssel unter den Kaffeeauslauftrichter. Führen Sie
keine Kapsel ein und vergewissern Sie sich, dass der Hebel geschlossen
ist.
25 sec
°C
4 Drücken Sie den Ein-/Ausschalter, um die Maschine einzuschalten.
-
Der Ein-/Ausschalter blinkt langsam und zeigt das Aufheizen der
Maschine an.
5 Wenn alle Tasten dauerhaft leuchten, drücken Sie die Lungo-Taste.
-
Wasser fließt aus dem Kaffeeauslauftrichter.
Hinweis: Wenn der interne Wasserkreislauf leer ist, ist ein Brummton der
Maschine zu hören. Wenn die Maschine Wasser ausgibt, entsteht ein
weniger lautes Brummgeräusch. Das ist normal.
6 Die Maschine ist betriebsbereit, wenn alle Tasten dauerhaft leuchten.
7 Entleeren Sie die Abtropfschale (siehe 'Schubladen für Kapselauswurf
und Restwasser reinigen') und die Restwasserschublade.
Die Maschine ist nun einsatzbereit.
23
Deutsch
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115

L'Or Barista LM8012/60 Manuel utilisateur

Catégorie
Accessoires de préparation de café
Taper
Manuel utilisateur
Ce manuel convient également à