Lincoln Electric LN-25 Mode d'emploi

Catégorie
Système de soudage
Taper
Mode d'emploi
LN-25 PORTABLE CV/CC
SEMIAUTOMATIC WIRE FEEDER
OPERATING MANUAL
IM923
November, 2007
For use with machines having Code Numbers: 11385, 11386
Safety Depends on You
Lincoln arc welding and cutting
equipment is designed and built with
safety in mind. However, your overall
safety can be increased by proper
installation ... and thoughtful opera-
tion on your part. DO NOT
INSTALL, OPERATE OR REPAIR
THIS EQUIPMENT WITHOUT
READING THIS MANUAL AND
THE SAFETY PRECAUTIONS
CONTAINED THROUGHOUT. And,
most importantly, think before you
act and be careful.
• Sales and Service through Subsidiaries and Distributors Worldwide •
Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.lincolnelectric.com
• World's Leader in Welding and Cutting Products •
Copyright © 2007 Lincoln Global Inc.
This manual covers equipment which is no
longer in production by The Lincoln Electric Co.
Specications and availability of optional
features may have changed.
FOR ENGINE
powered equipment.
1.a. Turn the engine off before troubleshooting and maintenance
work unless the maintenance work requires it to be running.
____________________________________________________
1.b. Operate engines in open, well-ventilated
areas or vent the engine exhaust fumes
outdoors.
____________________________________________________
1.c. Do not add the fuel near an open flame welding
arc or when the engine is running. Stop the engine
and allow it to cool before refueling to prevent
spilled fuel from vaporizing on contact with hot
engine parts and igniting. Do not spill fuel when
filling tank. If fuel is spilled, wipe it up and do not
start engine until fumes have been eliminated.
____________________________________________________
1.d. Keep all equipment safety guards, covers and devices in position
and in good repair.Keep hands, hair, clothing and tools away from V-
belts, gears, fans and all other moving parts when starting, operating
or repairing equipment.
____________________________________________________
1.e. In some cases it may be necessary to remove safety
guards to perform required maintenance. Remove
guards only when necessary and replace them when the
maintenance requiring their removal is complete.
Always use the greatest care when working near moving
parts.
___________________________________________________
1.f. Do not put your hands near the engine fan. Do not
attempt to override the governor or idler by push-
ing on the throttle control rods while the engine is
running.
___________________________________________________
1.g. To prevent accidentally starting gasoline engines while
turning the engine or welding generator during maintenance
work, disconnect the spark plug wires, distributor cap or
magneto wire as appropriate.
i
SAFETY
i
ARC WELDING CAN BE HAZARDOUS. PROTECT YOURSELF AND OTHERS FROM POSSIBLE SERIOUS INJURY OR DEATH. KEEP
CHILDREN AWAY. PACEMAKER WEARERS SHOULD CONSULT WITH THEIR DOCTOR BEFORE OPERATING.
Read and understand the following safety highlights. For additional safety information, it is strongly recommended that you purchase a copy of “Safety in
Welding & Cutting - ANSI Standard Z49.1” from the American Welding Society, P.O. Box 351040, Miami, Florida 33135 or CSA Standard W117.2-1974. A
Free copy of “Arc Welding Safety” booklet E205 is available from the Lincoln Electric Company, 22801 St. Clair Avenue, Cleveland, Ohio 44117-1199.
BE SURE THAT ALL INSTALLATION, OPERATION, MAINTENANCE AND REPAIR PROCEDURES ARE PERFORMED ONLY BY
QUALIFIED INDIVIDUALS.
WARNING
Mar ʻ95
ELECTRIC AND
MAGNETIC FIELDS
may be dangerous
2.a. Electric current flowing through any conductor causes
localized Electric and Magnetic Fields (EMF). Welding
current creates EMF fields around welding cables and
welding machines
2.b. EMF fields may interfere with some pacemakers, and
welders having a pacemaker should consult their physician
before welding.
2.c. Exposure to EMF fields in welding may have other health
effects which are now not known.
2.d. All welders should use the following procedures in order to
minimize exposure to EMF fields from the welding circuit:
2.d.1. Route the electrode and work cables together - Secure
them with tape when possible.
2.d.2. Never coil the electrode lead around your body.
2.d.3. Do not place your body between the electrode and
work cables. If the electrode cable is on your right
side, the work cable should also be on your right side.
2.d.4. Connect the work cable to the workpiece as close as
possible to the area being welded.
2.d.5. Do not work next to welding power source.
1.h. To avoid scalding, do not remove the
radiator pressure cap when the engine is
hot.
CALIFORNIA PROPOSITION 65 WARNINGS
Diesel engine exhaust and some of its constituents
are known to the State of California to cause cancer,
birth defects, and other reproductive harm.
The engine exhaust from this product contains chemi-
cals known to the State of California to cause cancer,
birth defects, or other reproductive harm.
The Above For Diesel Engines
The Above For Gasoline Engines
ii
SAFETY
ii
ARC RAYS can burn.
4.a. Use a shield with the proper filter and cover
plates to protect your eyes from sparks and
the rays of the arc when welding or observing
open arc welding. Headshield and filter lens
should conform to ANSI Z87. I standards.
4.b. Use suitable clothing made from durable flame-resistant
material to protect your skin and that of your helpers from
the arc rays.
4.c. Protect other nearby personnel with suitable, non-flammable
screening and/or warn them not to watch the arc nor expose
themselves to the arc rays or to hot spatter or metal.
ELECTRIC SHOCK can kill.
3.a. The electrode and work (or ground) circuits
are electrically “hot” when the welder is on.
Do not touch these “hot” parts with your bare
skin or wet clothing. Wear dry, hole-freegloves
to insulate hands.
3.b. Insulate yourself from work and ground using dry insulation.
Make certain the insulation is large enough to cover your full
area of physical contact with work and ground.
In addition to the normal safety precautions, if welding
must be performed under electrically hazardous
conditions (in damp locations or while wearing wet
clothing; on metal structures such as floors, gratings or
scaffolds; when in cramped positions such as sitting,
kneeling or lying, if there is a high risk of unavoidable or
accidental contact with the workpiece or ground) use
the following equipment:
• Semiautomatic DC Constant Voltage (Wire) Welder.
• DC Manual (Stick) Welder.
• AC Welder with Reduced Voltage Control.
3.c. In semiautomatic or automatic wire welding, the electrode,
electrode reel, welding head, nozzle or semiautomatic
welding gun are also electrically “hot”.
3.d. Always be sure the work cable makes a good electrical
connection with the metal being welded. The connection
should be as close as possible to the area being welded.
3.e. Ground the work or metal to be welded to a good electrical
(earth) ground.
3.f. Maintain the electrode holder, work clamp, welding cable and
welding machine in good, safe operating condition.
Replace damaged insulation.
3.g. Never dip the electrode in water for cooling.
3.h. Never simultaneously touch electrically “hot” parts of
electrode holders connected to two welders because voltage
between the two can be the total of the open circuit voltage of
both welders.
3.i. When working above floor level, use a safety belt to protect
yourself from a fall should you get a shock.
3.j. Also see Items 6.c. and 8.
FUMES AND GASES
can be dangerous.
5.a. Welding may produce fumes and gases
hazardous to health. Avoid breathing these
fumes and gases.When welding, keep
your head out of the fume. Use enough
ventilation and/or exhaust at the arc to keep
fumes and gases away from the breathing zone. When
welding with electrodes which require special
ventilation such as stainless or hard facing (see
instructions on container or MSDS) or on lead or
cadmium plated steel and other metals or coatings
which produce highly toxic fumes, keep exposure as
low as possible and below Threshold Limit Values (TLV)
using local exhaust or mechanical ventilation. In
confined spaces or in some circumstances, outdoors, a
respirator may be required. Additional precautions are
also required when welding on galvanized steel.
5. b. The operation of welding fume control equipment is affected
by various factors including proper use and positioning of
the equipment, maintenance of the equipment and the spe-
cific welding procedure and application involved. Worker
exposure level should be checked upon installation and
periodically thereafter to be certain it is within applicable
OSHA PEL and ACGIH TLV limits.
5.c.
Do not weld in locations near chlorinated hydrocarbon
vapors
coming from degreasing, cleaning or spraying operations.
The heat and rays of the arc can react with solvent vapors
to
form phosgene, a highly toxic gas, and other irritating prod-
ucts.
5.d. Shielding gases used for arc welding can displace air and
cause injury or death. Always use enough ventilation,
especially in confined areas, to insure breathing air is safe.
5.e. Read and understand the manufacturerʼs instructions for this
equipment and the consumables to be used, including the
material safety data sheet (MSDS) and follow your
employerʼs safety practices. MSDS forms are available from
your welding distributor or from the manufacturer.
5.f. Also see item 1.b.
AUG 06
iii
SAFETY
iii
FOR ELECTRICALLY
powered equipment.
8.a. Turn off input power using the disconnect
switch at the fuse box before working on
the equipment.
8.b. Install equipment in accordance with the U.S. National
Electrical Code, all local codes and the manufacturerʼs
recommendations.
8.c. Ground the equipment in accordance with the U.S. National
Electrical Code and the manufacturerʼs recommendations.
CYLINDER may explode
if damaged.
7.a. Use only compressed gas cylinders
containing the correct shielding gas for the
process used and properly operating
regulators designed for the gas and
pressure used. All hoses, fittings, etc. should be suitable for
the application and maintained in good condition.
7.b. Always keep cylinders in an upright position securely
chained to an undercarriage or fixed support.
7.c. Cylinders should be located:
Away from areas where they may be struck or subjected to
physical damage.
A safe distance from arc welding or cutting operations and
any other source of heat, sparks, or flame.
7.d. Never allow the electrode, electrode holder or any other
electrically “hot” parts to touch a cylinder.
7.e. Keep your head and face away from the cylinder valve outlet
when opening the cylinder valve.
7.f. Valve protection caps should always be in place and hand
tight except when the cylinder is in use or connected for
use.
7.g. Read and follow the instructions on compressed gas
cylinders, associated equipment, and CGA publication P-l,
“Precautions for Safe Handling of Compressed Gases in
Cylinders,” available from the Compressed Gas Association
1235 Jefferson Davis Highway, Arlington, VA 22202.
Jan, 07
WELDING and CUTTING
SPARKS can
cause fire or explosion.
6.a.
Remove fire hazards from the welding area.
If this is not possible, cover them to prevent
the welding sparks from starting a fire.
Remember that welding sparks and hot
materials from welding can easily go through small cracks
and openings to adjacent areas. Avoid welding near
hydraulic lines. Have a fire extinguisher readily available.
6.b. Where compressed gases are to be used at the job site,
special precautions should be used to prevent hazardous
situations. Refer to “Safety in Welding and Cutting” (ANSI
Standard Z49.1) and the operating information for the
equipment being used.
6.c. When not welding, make certain no part of the electrode
circuit is touching the work or ground. Accidental contact
can cause overheating and create a fire hazard.
6.d. Do not heat, cut or weld tanks, drums or containers until the
proper steps have been taken to insure that such procedures
will not cause flammable or toxic vapors from substances
inside. They can cause an explosion even
though
they have
been “cleaned”. For information, purchase “Recommended
Safe Practices for the
Preparation
for Welding and Cutting of
Containers and Piping That Have Held Hazardous
Substances”, AWS F4.1 from the American Welding Society
(see address above).
6.e. Vent hollow castings or containers before heating, cutting or
welding. They may explode.
6.f.
Sparks and spatter are thrown from the welding arc. Wear oil
free protective garments such as leather gloves, heavy shirt,
cuffless trousers, high shoes and a cap over your hair. Wear
ear plugs when welding out of position or in confined places.
Always wear safety glasses with side shields when in a
welding area.
6.g. Connect the work cable to the work as close to the welding
area as practical. Work cables connected to the building
framework or other locations away from the welding area
increase the possibility of the welding current passing
through lifting chains, crane cables or other alternate cir-
cuits. This can create fire hazards or overheat lifting chains
or cables until they fail.
6.h. Also see item 1.c.
6.I. Read and folllow NFPA 51B Standard for Fire Prevention
During Welding, Cutting and Other Hot Work”, available
from NFPA, 1 Batterymarch Park,PO box 9101, Quincy, Ma
022690-9101.
6.j. Do not use a welding power source for pipe thawing.
iv
SAFETY
iv
Mar. ʻ93
PRÉCAUTIONS DE SÛRETÉ
Pour votre propre protection lire et observer toutes les instructions et
les précautions de sûreté specifiques qui parraissent dans ce manuel
aussi bien que les précautions de sûreté générales suivantes:
Sûreté Pour Soudage A LʼArc
1. Protegez-vous contre la secousse électrique:
a. Les circuits à lʼélectrode et à la piéce sont sous tension
quand la machine à souder est en marche. Eviter toujours
tout contact entre les parties sous tension et la peau nue ou
les vétements mouillés. Porter des gants secs et sans trous
pour isoler les mains.
b. Faire trés attention de bien sʼisoler de la masse quand on
soude dans des endroits humides, ou sur un plancher met-
allique ou des grilles metalliques, principalement dans l e s
positions assis ou couché pour lesquelles une grande partie
du corps peut être en contact avec la masse.
c. Maintenir le porte-électrode, la pince de masse, le câble de
soudage et la machine à souder en bon et sûr état defonc-
tionnement.
d.Ne jamais plonger le porte-électrode dans lʼeau pour le
refroidir.
e. Ne jamais toucher simultanément les parties sous tension des
porte-électrodes connectés à deux machines à souder parce
que la tension entre les deux pinces peut être le total de la
tension à vide des deux machines.
f. Si on utilise la machine à souder comme une source de
courant pour soudage semi-automatique, ces precautions
pour le porte-électrode sʼapplicuent aussi au pistolet de
soudage.
2. Dans le cas de travail au dessus du niveau du sol, se protéger
contre les chutes dans le cas ou on recoit un choc. Ne jamais
enrouler le câble-électrode autour de nʼimporte quelle partie du
corps.
3. Un coup dʼarc peut être plus sévère quʼun coup de soliel, donc:
a. Utiliser un bon masque avec un verre filtrant approprié ainsi
quʼun verre blanc afin de se protéger les yeux du rayon-
nement de lʼarc et des projections quand on soude ou quand
on regarde lʼarc.
b. Porter des vêtements convenables afin de protéger la peau
de soudeur et des aides contre le rayonnement de lʻarc.
c. Protéger lʼautre personnel travaillant à proximité au soudage
à lʼaide dʼécrans appropriés et non-inflammables.
4. Des gouttes de laitier en fusion sont émises de lʼarc de soudage.
Se protéger avec des vêtements de protection libres de lʼhuile,
tels que les gants en cuir, chemise épaisse, pantalons sans
revers, et chaussures montantes.
5. Toujours porter des lunettes de sécurité dans la zone de
soudage. Utiliser des lunettes avec écrans lateraux dans les
zones où lʼon pique le laitier.
6. Eloigner les matériaux inflammables ou les recouvrir afin de
prévenir tout risque dʼincendie dû aux étincelles.
7. Quand on ne soude pas, poser la pince à une endroit isolé de la
masse. Un court-circuit accidental peut provoquer un échauffe-
ment et un risque dʼincendie.
8. Sʼassurer que la masse est connectée le plus prés possible de la
zone de travail quʼil est pratique de le faire. Si on place la masse
sur la charpente de la construction ou dʼautres endroits éloignés
de la zone de travail, on augmente le risque de voir passer le
courant de soudage par les chaines de levage, câbles de grue,
ou autres circuits. Cela peut provoquer des risques dʼincendie ou
dʼechauffement des chaines et des câbles jusquʼà ce quʼils se
rompent.
9. Assurer une ventilation suffisante dans la zone de soudage. Ceci
est particuliérement important pour le soudage de tôles gal-
vanisées plombées, ou cadmiées ou tout autre métal qui produit
des fumeés toxiques.
10. Ne pas souder en présence de vapeurs de chlore provenant
dʼopérations de dégraissage, nettoyage ou pistolage. La chaleur
ou les rayons de lʼarc peuvent réagir avec les vapeurs du solvant
pour produire du phosgéne (gas fortement toxique) ou autres pro-
duits irritants.
11. Pour obtenir de plus amples renseignements sur la sûreté, voir le
code “Code for safety in welding and cutting” CSA Standard W
117.2-1974.
PRÉCAUTIONS DE SÛRETÉ POUR
LES MACHINES À SOUDER À
TRANSFORMATEUR ET À
REDRESSEUR
1. Relier à la terre le chassis du poste conformement au code de
lʼélectricité et aux recommendations du fabricant. Le dispositif de
montage ou la piece à souder doit être branché à une bonne
mise à la terre.
2. Autant que possible, Iʼinstallation et lʼentretien du poste seront
effectués par un électricien qualifié.
3. Avant de faires des travaux à lʼinterieur de poste, la debrancher à
lʼinterrupteur à la boite de fusibles.
4. Garder tous les couvercles et dispositifs de sûreté à leur place.
v
v
Thank You
for selecting a QUALITY product by Lincoln Electric. We want you
to take pride in operating this Lincoln Electric Company product
••• as much pride as we have in bringing this product to you!
Read this Operators Manual completely before attempting to use this equipment. Save this manual and keep it
handy for quick reference. Pay particular attention to the safety instructions we have provided for your protection.
The level of seriousness to be applied to each is explained below:
WARNING
This statement appears where the information must be followed exactly to avoid serious personal injury or loss of life.
This statement appears where the information must be followed to avoid minor personal injury or damage to this equipment.
CAUTION
Please Examine Carton and Equipment For Damage Immediately
When this equipment is shipped, title passes to the purchaser upon receipt by the carrier. Consequently, Claims
for material damaged in shipment must be made by the purchaser against the transportation company at the
time the shipment is received.
Please record your equipment identification information below for future reference. This information can be
found on your machine nameplate.
Product _________________________________________________________________________________
Model Number ___________________________________________________________________________
Code Number or Date Code_________________________________________________________________
Serial Number____________________________________________________________________________
Date Purchased___________________________________________________________________________
Where Purchased_________________________________________________________________________
Whenever you request replacement parts or information on this equipment, always supply the information you
have recorded above. The code number is especially important when identifying the correct replacement parts.
On-Line Product Registration
- Register your machine with Lincoln Electric either via fax or over the Internet.
• For faxing: Complete the form on the back of the warranty statement included in the literature packet
accompanying this machine and fax the form per the instructions printed on it.
• For On-Line Registration: Go to our
WEB SITE at www.lincolnelectric.com. Choose “Quick Links” and then
“Product Registration”. Please complete the form and submit your registration.
CUSTOMER ASSISTANCE POLICY
The business of The Lincoln Electric Company is manufacturing and selling high quality welding equipment, consumables, and cutting equip-
ment. Our challenge is to meet the needs of our customers and to exceed their expectations. On occasion, purchasers may ask Lincoln
Electric for advice or information about their use of our products. We respond to our customers based on the best information in our posses-
sion at that time. Lincoln Electric is not in a position to warrant or guarantee such advice, and assumes no liability, with respect to such infor-
mation or advice. We expressly disclaim any warranty of any kind, including any warranty of fitness for any customerʼs particular purpose,
with respect to such information or advice. As a matter of practical consideration, we also cannot assume any responsibility for updating or
correcting any such information or advice once it has been given, nor does the provision of information or advice create, expand or alter any
warranty with respect to the sale of our products.
Lincoln Electric is a responsive manufacturer, but the selection and use of specific products sold by Lincoln Electric is solely within the control
of, and remains the sole responsibility of the customer. Many variables beyond the control of Lincoln Electric affect the results obtained in
applying these types of fabrication methods and service requirements.
Subject to Change – This information is accurate to the best of our knowledge at the time of printing. Please refer to www.lincolnelectric.com
for any updated information.
vi
SAFETY ..............................................................................................................................................................i-iv
INSTALLATION .....................................................................................................................................SECTION A
Technical Specifications .................................................................................................................................A-1
Safety Precautions...........................................................................................................................................A-2
Power Source Connections ............................................................................................................................A-2
Gun Cable Connection to Feeder..................................................................................................................A-3
Weld Cable Connection ..................................................................................................................................A-4
Electrode Cable Connection ......................................................................................................................A-4
Work Cable Connection .............................................................................................................................A-4
Wire Feed Drive Roll and Guide Tube Kits..................................................................................................A-4
OPERATION...........................................................................................................................................SECTION B
Safety Precautions...........................................................................................................................................B-1
General Description.........................................................................................................................................B-1
Recommended Processes and Equipment ..................................................................................................B-1
Welding Capability ...........................................................................................................................................B-1
Controls and Settings......................................................................................................................................B-2
Sequence of Operation ...................................................................................................................................B-4
Loading Electrode .......................................................................................................................................B-4
Loading Wire Drive .....................................................................................................................................B-5
Idle Roll Pressure Setting ..........................................................................................................................B-5
Presetting Wire Feed Speed .....................................................................................................................B-6
Making a Weld.............................................................................................................................................B-7
Procedure at End of Coil ................................................................................................................................B-8
Automatic Protection Shutdown.....................................................................................................................B-8
ACCESSORIES .....................................................................................................................................SECTION C
LN-25 Option Chart .........................................................................................................................................C-1
Options and Accessories................................................................................................................................C-2
K430-2 Gas Solenoid Kit............................................................................................................................C-2
K434-1 Gas Flow Timer Kit .......................................................................................................................C-2
K460-1 Pulse Power Adapter Kit ..............................................................................................................C-3
K461 Pulse Power Control Cable Assembly...........................................................................................C-3
K443-2, K443-3 LN-25 Contactor Kits ....................................................................................................C-3
Remote Output Control Options and Control Cable Assemblies..............................................................C-3
K431-1 Remote Output Control Kit...........................................................................................................C-3
K433-1 Power Source Remote Box .........................................................................................................C-4
K432 Remote Control Cable Assembly ...................................................................................................C-4
K439 Remote Extension Cable Assembly...............................................................................................C-4
K624-2 42V Remote Output Control Module ..........................................................................................C-4
K625, K626, K626 Remote Control Cable Assembly ............................................................................C-4
K444, K444-1 or K444-2 Remote Voltage Control Kit ...........................................................................C-5
K557-1 Rear Handle Kit .............................................................................................................................C-5
MAINTENANCE
.....................................................................................................................................SECTION D
Safety Precautions ..........................................................................................................................................D-1
Routine Maintenance ......................................................................................................................................D-1
Circuit Protection and Automatic Shutdown ................................................................................................D-1
Adjusting Speed Sensor Module ...................................................................................................................D-1
Calibration of the LN-25 Wire Speed Dial....................................................................................................D-2
TROUBLESHOOTING GUIDE.............................................................................................................SECTION E
How to Use the Troubleshooting Guide .......................................................................................................E-1
Troubleshooting Guide....................................................................................................................................E-2
WIRING DIAGRAM................................................................................................................................SECTION F
PHYSICAL DIMENSIONS.....................................................................................................................SECTION F
PARTS MANUAL ..............................................................................................................................P-553 SERIES
TABLE OF CONTENTS
vi
LN-25
A-1
TEMPERATURE RANGE
OPERATION: - 40
o
C to +40
o
C (- 40
o
F to +104
o
F)
STORAGE: - 40
o
C to +85
o
C (- 40
o
F to +185
o
F)
A-1
OPERATING ARC VOLTAGE
Constant Voltage (CV)
or 15-40 VDC (110VDC Maximum OCV)
Constant Current (CC)
RATED CURRENT
Rated current without contactor 500 Amps 60% Duty Cycle
Rated current with contactor 300 Amps 60% Duty Cycle
WIRE SPEED RANGE
50 – 700 Inches Per Minute (IPM)
RECOMMENDED ELECTRODE WIRE SIZES
.023” to
1
16 SOLID STEEL WIRE
.045” to
5
64 CORED WIRE
.035” to
1
16 ALUMINUM WIRE
PHYSICAL DIMENSIONS
HEIGHT WIDTH DEPTH WEIGHT
(Handle Down) w/o Options
14 Inches 7.4 Inches 21 Inches 28 lbs
(354 mm) (187 mm) (531 mm) (13 kg)
RRAATTEEDD CCUURRRREENNTT
WWIIRREE FFEEEEDD SSPPEEEEDD
PPHHYYSSIICCAALL DDIIMMEENNSSIIOONNSS
EENNVVIIRROONNMMEENNTTAALL RRAATTIINNGG
WWIIRREE DDIIAAMMEETTEERRSS
VVOOLLTTAAGGEE
INSTALLATION
TECHNICAL SPECIFICATIONS – LN-25
IP23
LN-25
A-2
A-2
INSTALLATION
ELECTRIC SHOCK can kill.
Do not operate with covers
removed.
Turn off power source before
installing or servicing.
Do not touch electrically
hot parts.
Turn the input power to the
welding power source off at the
fuse box before working in the
terminal strip.
Only qualified personnel should
install, use or service this
equipment.
DC-250
a. Connect a jumper from 2 to 4 on the power source
terminal strip so the output will be energized when
the DC-250 is turned on.
b. Connect electrode cable to the “Innershield/
GMAW” output terminal of polarity required by
electrode. Connect work lead to other
“Innershield/GMAW” output terminal.
c. Place “Set to CV Electrode Cable Polarity” switch
at appropriate position.
d. Place power source toggle switch in “Output
Control at DC-250” position, unless a Remote
Control is connected to 75, 76 and 77 on the DC-
250 terminal strip.
e. Place mode switch in “Innershield GMAW (CV)”
position. Set CV arc control to “2” (or “NORMAL”
on some machines). Initially set the output
control on “7”.
DC-400 AND CV-400
a. Connect a jumper from 2 to 4 on the power
source terminal strip so the output will be
energized when the power source is turned on.
NOTE: DC-400 machines above Code 9200 have
an output toggle switch to perform this function.
b. Connect the electrode cable to the output
terminal of polarity required by electrode.
Connect work lead to other output terminal.
SAFETY PRECAUTIONS
Unless an optional output control or contactor is used
with the LN-25, the electrode circuit (including welding
wire, wire drive and welding gun) is electrically hot
when the welding power source is on. The gun trigger
controls wire feed only.
Disconnect or shut off welding power source before
making connections or installations to the LN-25.
Welding gun should be stored in the insulated
gun holder, located near the rear on the top of the
LN-25 case, to avoid accidental arcing.
The LN-25 should be positioned upright on a
horizontal surface.
ELECTRIC SHOCK can kill.
Do not touch metal portions
of the LN-25 lead clip when
welding power source is on.
POWER SOURCE CONNECTION
The LN-25 can be used with most DC welding power
source. A constant voltage power source is
recommended; however, the LN-25 can also be used
with a constant current power source as long as the
open circuit voltage is less than 110V DC.
Do not use LN-25 models below Code 9200 with any
TIG or Square Wave welding power sources. Do not
use LN-25 models equipped with internal contactors
with non- Lincoln TIG or Square Wave welding power
sources. Damage to the LN-25 circuit can occur as a
result of the high output inductance typically
associated with these power sources. TIG high
frequency power should never be applied to the LN-25.
If not using an LN-25 Remote Output Control option
(See Remote Output Control Options and Cable
Assemblies Section), the power source output must
be electrically “hot” at all times when the power
source is turned on.
See the power source instruction manual for proper
power source connections and setting required.
WARNING
WARNING
WARNING
CAUTION
LN-25
A-3
A-3
c. Set ELECTRODE POLARITY switch to constant
voltage polarity required by electrode.
d. Set toggle switch to “Constant Voltage” and set
the Constant Voltage Control on welder and the
portable field control on #5 for initial start.
SA-200, —250 OR SAE-300, —400 (WITH
CV ADAPTER)
a. For electrode negative welding, connect the
electrode lead from the LN-25 to the output
terminal on the CV Adapter, and the work lead to
the power source output terminal labeled
“POSITIVE”. For electrode positive welding,
interchange the above lead connections so the
LN-25 electrode lead is then connected to the
positive power source terminal.
b. Place both switches on the CV Adapter to the CV
INNERSHIELD position and make appropriate
power source settings per the CV Adapter instruc-
tions provided for the power source being used.
c. The output voltage is set with the voltage control
on the CV Adapter.
NOTE: Refer to the Instruction Manual provided with
the machine for details on connection and operation
of the LN-25 with the power source.
INVERTEC, CV300 AND OTHER NEWER
LINCOLN POWER SOURCES
Refer to the instruction manual provided with the
power source for details on connection and operation
of the LN-25 with these newer machines.
GUN CABLE CONNECTION
TO FEEDER
Lay the cable out straight. Insert the connector on the
welding conductor cable into the brass conductor
block on the front of the wire drive unit. Make sure it is
all the way in and tighten the hand wheel clamp. Keep
this connection clean and bright. Connect the control
cable polarized amphenol plug into the mating 5-cavity
receptacle on the front panel of the wire feeder case.
FOR GMA GUN AND CABLES:
Requires installation of K430-1 Gas Solenoid Kit
(factory installed on K446 and K449-3 models).
See K430-1 Gas Solenoid Kit Section (in Accessories
Section) for gas solenoid operation and gas supply
connection.
c. Place “Set to Same Polarity As Electrode Cable
Connection” switch at appropriate position.
d. Place power source toggle switch in “Output
Control at DC(CV) -400” position, unless a
remote control is connected to 75, 76 and 77 on
the power source terminal strip.
e. If power source has a mode switch, set switch to
Constant Voltage Innershield. Initially set the
output control on “6”.
DC-600
a. Connect a jumper from 2 to 4 on the power
source terminal strip so the output will be
energized when the DC-600 is turned on. (For
DC-600 below Code 8200, also jumper N to S.)
b. Connect the electrode cable to the output
terminal of polarity required by electrode.
Connect work lead to other output terminal.
c. Place “Set to Same Polarity As Electrode Cable
Connection” switch at appropriate position.
d. Place power source toggle switch in “Output
Control at DC-600” position, unless a remote
control is connected to 75, 76 and 77 on the DC-
600 terminal strip.
e. Set mode switch to Constant Voltage Innershield.
Initially set output control on “4”.
R3S-325
a. Connect a jumper from 4 to 32 on the power
source terminal strip so that the output will be
energized when the R3S-325 is turned on.
b. Connect the electrode cable to the output
terminal of polarity required by electrode.
Connect work lead to other output terminal.
c. Set power source per its instruction manual.
NOTE: Use of the optional Line Voltage
Compensator available for the R3S-325 is
recommended if input line voltage variation
exceeds ±3%.
SAM-400, —650
a. Connect a jumper from 2 to C4 on the power
source terminal strip so the output will be
energized when the SAM power source is on.
b. Connect work lead to WORK stud. Connect
electrode to AUTO EQUIPMENT stud. Connect
SAM-650 “Tap” lead to the Innershield stud
desired.
INSTALLATION
LN-25
A-4
A-4
INSTALLATION
Install the barbed fitting and union nut to the 5/8-18
female inert gas fitting on the front panel of the
LN-25 case. Connect the 3/16” I.D. gas hose from
the gun cable to the barbed fitting.
When the gun is to be removed, this fitting can be
easily detached by loosening the union nut.
WELD CABLE CONNECTION
The size of the electrode cable and work cable must
be sufficient for the maximum weld current and total
cable length to be used. Refer to table A.1.
TABLE A.1
Total Cable Length
Weld Current
60% Duty Cycle 50ʼ-100ʼ 100ʼ-150ʼ 150ʼ-200ʼ 200ʼ-250ʼ
200Amps 2 AWG 2 AWG 1 AWG 1/0
300Amps 1 AWG 1 AWG 1/0 2/0
400Amps 2/0 2/0 3/0 3/0
500Amps 2/0 3/0 3/0 4/0
ELECTRODE CABLE CONNECTION
Route the electrode cable through the oval hole in
the lower portion of the LN-25 rear panel. Connect
the electrode cable to the LN-25 input stud using the
1/2” nut provided.
Secure the cable with the strain relief clamp provided.
All units are supplied with an optional pigtail for
customers that prefer to make a taped and bolted
connection externally.
WORK CABLE CONNECTION
Connect a work lead of sufficient size between
the proper output stud on the power source and
the work. Be sure the connection to the work
makes tight metal-to-metal electrical contact.
Poor work lead connections can result in poor
welding performance.
WIRE FEED DRIVE ROLL AND
GUIDE TUBE KITS
Turn off power source before installing or changing
drive roll and/or guide tubes.
NOTE: The maximum wire sizes the LN-25 will
satisfactorily feed are 5/16” cored and 1/16” solid
electrodes.
The electrode sizes that can be fed with each roll and
guide tube are stencilled
(1)
on each part. Check the kit
for proper components. See the instructions, included
with the drive roll kit, to install these parts on new
machines or replace them on used machines. Refer
to table A.2.
TABLE A.2
Kit Instructions
Steel Wire Sizes:
.068-5/64 Cored KP653-3/32 L9932
1/16 (.062) Cored or Solid -1/16
Steel
(Can also be used for .052)
.045 and .052 Solid Steel -.052
.045 and .052 Cored -.052C
.035 Solid Steel -.035S
.035 Cored -.035C
.030 Solid Steel -.030S
.025 Solid Steel -.025S
Aluminum Wire Sizes:
1/16 KP654-1/16A L9932
3/64 -3/64A
.035 -.035A
(1)
Drive rolls for only cored electrode sizes are stencilled with a
“C” suffix to the wire sizes.
Drive rolls for only solid electrode sizes are stencilled with an
“S” suffix to the wire sizes.
Drive rolls for aluminum wire sizes are stencilled with an “A” suffix
to the wire sizes.
WARNING
LN-25
B-1
B-1
ELECTRIC SHOCK can kill.
Do not touch electrically live
part or electrode with skin or
wet clothing.
Insulate yourself from work
and ground.
Always wear dry insulating
gloves.
ARC RAYS can burn.
Wear eye, ear and body protec-
tion.
FUMES AND GASSES can be
dangerous.
Keep your head out of fumes.
Use ventilation or exhaust to
remove fumes from breathing
zone.
WELDING SPARKS can cause
fire or explosion.
Keep flammable material away.
OPERATION
WARNING
GENERAL DESCRIPTION
The LN-25 is a lightweight portable semiautomatic
wire feeder designed for “across-the-arc” operation
without a control cable on most any DC welding
power source. Simply connect the LN-25 to the
electrode cable, clip it to Work and it is ready to weld,
using up to 30 lb. coils or spools.
The wire drive, controls and wire reel are fully
enclosed in a rugged molded plastic case providing
a compact and versatile welding package ideally
suited to “on-the-go” field welding applications in
virtually any environment.
RECOMMENDED PROCESSES
AND EQUIPMENT
When combined with the quality drive roll kits and
accessories available for use with the LN-25, a
versatile portable welding system can be provided to
meet the specific needs of Innershield, submerged
arc or gas metal arc welding applications within the
wire feed capabilities of the LN-25.
The LN-25 provides constant wire feed speed for use
with constant voltage (CV) power sources, and arc-
sensing wire feed speed for use with constant current
(CC) (formerly variable voltage) power sources. Wire
speed is presettable on a dual-range calibrated dial.
The power sources recommended for use with the
LN-25 include the DC-250, -400, -600, CV-400 and
R3S type transformer machines, and the SAM-400,
-650 engine welders, as well as the SA-200, -250 or
SAE-300, -400 with CV Adapter and Pulse Power
500 with K460-1 LN-25 Kit.
WELDING CAPABILITY
The LN-25 will handle up to 500 Amp 60% duty cycle
welding currents. However, when equipped with a
K443-2 Contactor, the LN-25 will handle up to 300
Amp 60% duty cycle.
SAFETY PRECAUTIONS
READ AND UNDERSTAND ENTIRE SECTION
BEFORE OPERATING MACHINE
LN-25
B-2
B-2
OPERATION
VOLTMETER
(Factory installed on model Codes above 9218)
The 40V DC analog voltmeter is mounted to the front
control panel of the LN-25 and is connected to read
the arc voltage between the LN-25 electrode cable
connection and the work clip lead.
NOTE:
1. The Voltmeter will read zero if the LN-25 work
clip lead is not connected to work, even if the
elec trode is electrically “hot” to work.
2. The Voltmeter will read below zero if the LN-25
polarity switch is not set to the same polarity as
the electrode.
3. The Voltmeter will read power source open
circuit voltage when the gun trigger is open, even
if the LN-25 is equipped with the internal
contactor.
“ELECTRODE POLARITY” SWITCH
The polarity switch is located on the front panel of
the LN-25 case.
Set the switch to the same polarity as the electrode
lead connection to the power source. If the switch is
not set for the correct polarity, the wire feeder will not
operate.
WIRE FEED MODE SWITCH
The CV-VV (CC) Wire Feed Mode switch is located
inside the LN-25 case. The toggle switch extends
from be neath the control box just above the wire
drive.
The forward “CV” position provides constant wire
feed speed mode for use with constant voltage (CV)
welding power sources.
The backward “VV (CC)” position provides arc-sensing
wire feed speed mode for use with constant current
(formerly variable voltage) welding power sources.
WIRE SPEED DIAL AND RANGE SWITCH
The Wire Speed control dial on the front panel of the
LN-25 has two calibrated dial ranges selected by the
HI-LO Dial Range switch.
When switched to the LO range position, the constant
wire feed speed (CV Wire Feed Mode) is set on the
inside (white) or (red) dial range calibrated for 50 to
350 in/min.
When switched to the HI range position, the constant
wire feed speed (CV Wire Feed Mode) is set on the
outside (black) or (blue) dial range calibrated
for 50 to 700 in/min.
LN-25 INSTRUMENTS AND
CONTROLS
Refer to Figure B.1 for control locations.
REMOTE
ARC VOLTAGE
CONTROL
(OPTIONAL)
WIRE SPEED
DIAL RANGE
SWITCH
WIRE
SPEED
DIAL
VOLT
METER
WORK CLIP
LEAD
GUN
CONNECTION
BLOCK
GUN
TRIGGER
AMPHENOL
CONNECTOR
GAS
FITTING
(OPTIONAL)
ELECTRODE
POLARITY
SWITCH
GAS POST/
PRE FLOW
TIMERS
(OPTIONAL)
ELECTRODE
CABLE
OPTIONAL
GAS INPUT
FITTING
GAS PURGE
BUTTON
FIGURE B.1 CONTROL LOCATIONS
LN-25
B-3
B-3
The volts marks around the HI range calibrated dial
indicate the minimum arc volts required to obtain the
indicated HI range wire feed speeds. For example;
if wire speed is set to 400 in/min., a welding
procedure arc voltage of at least 17V would be
required to obtain the 400 in/min. wire feed speed.
WORK CLIP LEAD
IMPORTANT SAFETY NOTE: To avoid possible
electrical shock, do not touch the metal portions of
the LN-25 work lead clip if the power source output
is on. The clip will be electrically “HOT” to work if the
input electrode cable to the LN- 25 is electrically
“HOT” even if the gun trigger is off and even if an
internal contactor is used. Care should be taken to
only handle the LN-25 work clip by its non-metal
insulated portions and/or the welding power source
should be turned off before handling the work clip.
--------------------------------------------------------------------
The 15 ft. (4.6m) work clip lead attached to the front
panel of the LN-25 case must be connected directly
to the work using the spring clip on the end of the
lead.
If not connected, the LN-25 will not operate even if
a K431-1 or K624-2 (42V) Remote Output Control
option (refer to Accessories Section) is used.
However, the electrode will still be electrically “HOT”
when the clip lead is dis connected, if K431-1 or
K624-1 (42V) Remote Output Control Option, or
Internal Contactor (K443-2), is not used.
OPERATION
When used with a K460-1 Pulse Power Adapter Kit,
the LN-25 does not need a clip lead.
NOTE: The clip lead also serves as a work sensing
lead for the LN-25 Voltmeter (if installed). If the clip
lead is extended by the user beyond the standard
15 ft. (4.6m) length, the voltmeter reading will be
lower than the actual arc volts due to the LN-25
motor control cur rent flowing through the resistance
of the extended lead. To minimize this voltmeter
error, the following minimum lead size is
recommended for the maximum extended lengths
shown:
AWG Maximum Length
#14 25 Ft(7.6m)
#12 50 Ft(15.2m)
#10 100 Ft(30.5m)
#6 200 Ft(61m)
REMOTE ARC VOLTAGE CONTROL (OPTIONAL)
This rheostat control allows you to control the power
source output arc voltage level. Refer to K444, K444-
1 and K444-2 Remote Voltage Kits in the
Accessories section.
GAS FITTING (OPTIONAL)
Provides gas output connection to the welding gun
for the GMAW process. Refer to K430-2 Gas
Solenoid Kit in the Accessories Section.
GAS POST PRE-FLOW TIMERS (OPTIONAL)
Allows for variable adjustment of gas pre-flow &
post-flow at the start and end of the weld. Refer to
K434-1 Gas Flow Timer Kit in Accessories Section.
WARNING
WARNING
ELECTRIC SHOCK can kill.
Do not touch metal portions
of the LN-25 lead clip when
welding power source is on.
-----------------------------------------------------------------------
B-4
B-4
OPERATION
g. To remove Readi-Reel from Adapter, depress re -
taining spring tab with thumb while pulling the
Readi-Reel cage from the molded adapter with
both hands. It is not necessary to remove
adapter from spindle.
h. Load wire into wire drive per Loading Wire Drive
Section.
MOUNTING 10 TO 30 LB SPOOLS
For 12” Diameter Spools:
a. Remove the locking collar and the Readi-Reel
adapter (if so equipped) on the 2” diameter
spindle (adapter is not required).
b. Place the spool on the spindle so the brake
holding pin enters one of the holes in the back
side of the spool. Be sure the wire comes off the
spool in a clockwise direction when dereeled
from the bot tom of the coil.
c. Replace and tighten the locking collar.
d. See Loading Wire Drive section for loading
instructions.
For 8” Diameter Spools (Requires optional K468
Spindle Adapter for 8” Spools):
a. Remove the locking collar and the Readi-Reel
adapter (if so equipped) on the 2” diameter
spindle (adapter is not required).
b. Slide S18221 Spindle Adapter onto the 2”
spindle so the brake holding pin enters the
adapter pin hole.
c. Place the spool on the spindle so the adapter tab
enters one of the holes in the back side of the
spool. Be sure the wire comes off the spool in a
clockwise direction when dereeled from the
bottom of the coil.
d. Replace and tighten the Locking Collar.
e. Load wire into wire drive per Loading Wire Drive
Section.
MOUNTING 13 OR 14 LB INNERSHIELD COILS
(Requires Op tional K435 Spindle Adapter for 14 lb
Coils.)
a. Remove the locking collar and the Readi-Reel
adapter (if so equipped) on the 2” diameter
spindle (adapter is not required).
b. Mount K435 Spindle Adapter and Innershield coil
per the Instructions (S18256) included with the
K435.
LOADING ELECTRODE
MOUNTING 22 TO 30 LB READI-REEL
®
COILS
The LN-25 will require an optional K363-P Readi-
Reel
®
Adapter which is required to load Lincoln 22 to
30 lb Readi-Reel coils.
a. Make certain that the threaded locking collar is
tight and securely locks the adapter on the
spindle (see figure B.2).
b. Rotate the spindle and adapter so the retaining
spring is at the 12 oʼclock position.
c. Position the Readi-Reel so that it will rotate in a
clockwise direction when feeding (wire is to be
de reeled from bottom of the coil).
d. Set one of the Readi-Reel inside cage wires on
the slot in the retaining spring tab.
e. Lower the Readi-Reel to depress the retaining
spring and align the other inside cage wires with
the grooves in the molded adapter.
f. Slide cage all the way onto the adapter until the
retaining spring “pops up” fully.
Check to be sure the retaining spring has fully
returned to the locking position and has securely
locked the Readi-Reel cage in place. Retaining
spring must rest on the cage, not the welding
electrode.
WARNING
WARNING
ELECTRIC SHOCK can kill.
Unless an optional output
control or internal contactor
is used with the LN-25, the
electrode circuit is electrically
“Hot” when the power source
is on.
• Turn off the power source
while mounting electrode
coils.
SEQUENCE OF OPERATION
LN-25
LN-25
B-5
B-5
LOADING WIRE DRIVE
a. Turn the reel or spool until the free end of the
electrode is accessible.
b. While tightly holding the electrode, cut off the
bent end and straighten the first six inches. Cut
off the first inch. (If the electrode is not properly
straightened, it may not feed or may not go into
the out going guide tube causing a “bird nest”.)
c. Insert the free end through the incoming guide
tube to the drive roll.
d. Turn on the welding power source.
Unless an optional output control or internal
contactor is used with the LN-25, the electrode circuit
is electrically “hot” when the power source is on.
e. Press the gun trigger and push the electrode
until it just enters the drive roll.
When inching with gun trigger, the electrode and
drive mechanism are always “hot” to work and
ground. Use the “cold” inch switch on models with
internal contactor.
f. Inch the electrode through the gun.
g. Adjust the brake tension with the thumbscrew on
the spindle hub until the reel turns freely, but
with little or no overrun when wire feeding is
stopped. Do not over tighten.
Keep gun in LN-25 gun holder when not feeding wire
to prevent accidental arcing.
IDLE ROLL PRESSURE SETTING
The idle roll pressure is set at the factory backed out
two turns from full pressure. This is an approximate
setting. For small wire sizes and aluminum wire, the
optimum idle roll pressure varies with type of wire,
surface condition, lubrication and hardness. The op -
timum idle roll setting can be determined as follows:
1. Press end of gun against a solid object that is
elec trically isolated from the welder output.
Press the gun trigger for several seconds.
2. If the wire “bird nests,” jams or breaks at the
drive roll, the idle roll pressure is too great. Back
the pressure setting out
1
2 turn, run new wire
through gun, and repeat above steps.
WARNING
WARNING
CAUTION
OPERATION
2" O.D. SPINDLE
MOLDED ADAPTER
RETAINING SPRING
INSIDE CAGE WIRES
READI-REEL
GROOVES
BRAKE HOLDING PIN-
(MUST ENGAGE HOLE IN-
ADAPTER RIB)
THREAD LOCKING COLLAR
FIGURE B.2 READI-REEL INSTALLATION
LN-25
B-6
B-6
OPERATION
3. If the only result is drive roll slippage, shut off
the power source, then loosen the gun cable
clamping screw in the gearbox conductor block
and pull the gun cable forward about six inches.
There should be a slight waviness in the
exposed wire. If there is no waviness, the
pressure is too low. Increase the pressure
setting
1
4 turn, lock the gun cable in place and
repeat the above steps.
PRESETTING WIRE FEED SPEED
The LN-25 permits accurate presetting of the desired
wire feed speed, before welding, in both CV and CC
wire feed modes.
SETTING CONSTANT WIRE FEED SPEED (CV
MODE)
a. Set Wire Feed Mode switch to CV position.
b. Set Dial Range switch to LO position for wire
feed speeds up to 350 in/min., or HI position for
wire feed speeds over 350 in/min.
c. Set Wire Feed dial to the desired wire feed
speed on the selected calibrated dial range.
The wire speed will remain constant at the value set,
independent of arc voltage changes, as long as the
arc voltage does not drop below the value per the
chart below for the max. wire feed speed shown:
Maximum Speed Minimum Arc Volts
350 IPM 15V
400 IPM 17V
500 IPM 21V
600 IPM 24V
700 IPM 27V
SETTING ARC SENSING WIRE FEED SPEED
(VV [CC] MODE)
When using a constant current (formerly variable
voltage) power source, welding performance is im -
proved using arc sensing wire feed speed (VV [CC]
mode). In this wire feed mode the wire speed
increases if arc voltage increases, and decreases if
arc voltage de creases, but remains constant at any
specific voltage level.
The LN-25 permits accurate VV (CC) mode
presetting of the desired wire feed speed, for the
desired arc voltage to be used, by setting the Wire
Speed dial in the fol lowing manner before welding:
a. Set Wire Feed Mode switch to VV (CC) position.
FIGURE B.3 CC WIRE SPEED SETTING
(Hl or LO Range)
b. Referring to the graph located above the Mode
switch (also shown in Figure B.3):
1. Select the horizontal line representing the DE -
SIRED IN/MIN. for the welding procedure. (See
example arrow line for 375 in/min.)
2. Select the diagonal line representing the ARC
VOLTS to be used for the welding procedure.
(See example arrow line for 29 volts.)
3. Determine the vertical line representing the CC
WIRE SPEED SETTING where the above two
lines cross. (See example arrow line for 450.)
c. Set the Wire Speed dial to the value determined
in Step (3) above (450 for example used). Use
HI Dial Range if value to be set is over 350.
The wire will feed at the DESIRED IN/MIN speed
when the welding power source is set to the arc
voltage to be used for the weld procedure (375
in/min. at 29V for example used).
A chart representation of the VV (CC) wire speed
setting graph is shown in Figure B.4, giving the Wire
Speed dial setting required for the DESIRED IN/MIN
and ARC VOLTS used for the welding procedures:
LN-25
B-7
B-7
Arc Volts Used
Desired
In/Min 16 18 20 22 24 26 28 30 32 34
50 109 97 88 80 73 67 63 58 55 51
60 131 117 105 95 88 81 75 70 66 62
70 153 136 123 111 102 94 88 82 77 72
80 175 156 140 127 117 108 100 93 88 82
90 197 175 158 143 131 121 113 105 98 93
100 219 194 175 159 146 135 125 117 109 103
110 241 214 193 175 160 148 138 128 120 113
120 263 233 210 191 175 162 150 140 131 124
130 284 253 228 207 190 175 163 152 142 134
140 306 272 245 223 204 188 175 163 153 144
150 328 292 263 239 219 202 188 175 164 154
160 350 311 280 255 233 215 200 187 175 165
170 372 331 298 270 248 229 213 198 186 175
180 394 350 315 286 263 242 225 210 197 185
190 416 369 333 302 277 256 238 222 208 196
200 438 389 350 318 292 269 250 233 219 206
210 459 408 368 334 306 283 263 245 230 216
220 481 428 385 350 321 296 275 257 241 226
230 503 447 403 366 335 310 288 268 252 237
240 525 467 420 382 350 323 300 280 263 247
250 547 486 438 398 365 337 313 292 273 257
260 569 506 455 414 379 350 325 303 284 268
270 591 525 473 430 394 365 338 315 295 278
280 613 544 490 445 408 377 350 327 306 288
290 634 564 508 461 423 390 363 338 317 299
300 656 583 525 477 438 404 375 350 328 309
310 678 603 543 493 452 417 388 362 339 319
320 700 622 560 509 467 431 400 373 350 329
330 642 578 525 481 444 413 385 361 340
340 661 595 541 496 458 425 397 372 350
350 681 613 557 510 471 438 408 383 360
360 700 630 572 526 484 450 420 394 370
380 666 604 554 512 472 444 416 392
400 700 636 584 538 500 466 438 412
420 668 612 566 526 490 460 432
440 700 642 592 550 514 482 452
460 670 620 576 536 504 472
480 700 646 600 560 526 494
500 674 626 584 546 514
520 700 650 606 568 536
540 676 630 590 556
560 700 654 612 576
580 676 634 598
600 700 656 618
620 678 638
640 700 658
660 680
680 700
700
MAKING A WELD
The serviceability of a product or structure utilizing
the LN-25 wire feeder is and must be the sole
responsibility of the builder/user. Many variables
beyond the control of The Lincoln Electric Company
affect the results obtained in using the LN-25 wire
feeder. These variables include, but are not limited to,
welding procedure, plate chemistry and temperature,
weldment design, fabrication methods and service
requirements. The available range of the LN-25 wire
feeder may not be suitable for all applications, and
the builder/user is and must be solely responsible for
welding settings.
SETUP
a. Connect work cable to metal to be welded. Work
cable must make good electrical contact to the
work. The work must also be grounded as stated
in “Arc Welding Safety Precautions.”
b. Check that the LN-25 is properly connected to
the power source for the polarity and process to
be used, and appropriate power source settings
are made for the procedure to be used. (Refer to
power source operating and connection
instructions.)
NOTE: If the K431-1 Remote Output Control Kit or
K624-2 42V Remote Control Module is installed but
the LN-25 is to be used without the K432 Remote
Control Cable Assembly, then the Remote Board
harness plug must be removed from the 16-pin
receptacle on the Control Board and the jumper plug
(T13498-21) reinstalled.
NOTE: If the K460-1 Pulse Power Adapter Kit is
installed but the LN-25 is to be used without the K461
Pulse Power Control Cable Assembly, then the
instructions for returning the unit to across the arc
operation included with the Installation Instructions
(L9636) must be followed.
c. Place the LN-25 conveniently near the work area
in a location to minimize exposure to weld spatter
and to avoid sharp bends in the gun cable.
d. Connect the LN-25 Clip Lead to work and set Po -
larity Switch to same polarity as electrode.
e. Set WIRE FEED MODE switch to CV or CC, as
appropriate for the power source, then set the
proper DIAL RANGE and WIRE SPEED dial set -
ting for the proper wire feed speed per the
welding procedure:
VV (CC) Speed Setting =
Desired IPM
X 35
( Arc Volts)
OPERATION
FIGURE B.4 VV(CC) WIRE SPEED SETTING
For CV: Set dial to the calibrated IN/MIN
desired. (Refer to Setting Constant Wire Feed
Speed Section.)
For CC: Set dial to value determined from the
CC Wire Speed Graph for the DESIRED IN/
MIN and ARC VOLTS to be used. (Refer to
Setting Arc Sensing Wire Feed Speed
Section.)
NOTE: If procedure permits a range of acceptable
arc voltage, use the middle of the range to
determine proper WIRE SPEED setting.
f. If using the optional Gas Flow Timer, set the de -
sired PREFLOW TIME and POSTFLOW TIME.
g. Be sure the proper contact tip for the wire size
being used is in the gun, and the gun is safe
from work contact. (Use the LN-25 insulated
gun holder.)
h. Turn on the welding power source, as well as the
shielding gas supply (if used).
Unless an optional output control or internal contactor
is used, the electrode is elec trically “hot” when the
power source is on. The gun trigger controls wire
feed and gas supplied to the nozzle area (if used).
-----------------------------------------------------------------
B-8
B-8
ARC RAYS can burn.
Do not touch metal por-
tions of the LN-25 lead Clip
when welding power
source is on.
--------------------------------------------------------------------
OPERATION
CYLINDER may explode if
damaged.
Keep cylinder upright and
chained to support.
Keep cylinder away from
areas where it may be dam-
aged.
Never lift welder with cylin-
der attached
Never allow welding elec-
trode to touch cylinder.
Keep cylinder away from
welding or other live electri-
cal circuits.
----------------------------------------------------------------------
WARNING
WARNING
WARNING
OPEN ARC WELDING WITH A
CONSTANT CURRENT (formerly
variable voltage) POWER SOURCE
The LN-25 should be used with a constant current
machine only upon non-critical weldments and after
testing is done to assure quality is adequate for the
application.
------------------------------------------------------------------
PROCEDURE AT END OF COIL
When the wire on the reel is used up, the following
procedure is to be followed for removing the old wire
from the gun cable and loading a new reel.
a. Shut off power source if a Remote Output
Control Option or internal contactor is not used.
b. Cut the end of the electrode off at the gun end.
Do not break it off by hand since this puts a slight
bend in the wire and makes it difficult or
impossible to pull it back through the nozzle.
c. Uncouple the gun conductor cable from
the LN-25.
d. Lay the cable out straight.
e. Using pliers to grip the wire, pull it out of the
cable from the connector end. Do not pull it from
the gun end.
f. Put the conductor cable back on wire drive unit
after the electrode has been removed.
g. Load a new coil of wire and feed it through the
cable as described in Loading Electrode Section.
WELDING
WARNING
a. Cut the electrode within approximately 3/8” of the
end of the contact tip for solid wire and within
approximately 3/4” of the extension guide for
cored wire.
b. Position electrode over joint. End of electrode
should be slightly off the work.
c. Lower welding helmet, close gun trigger, and
begin welding. Hold the gun so the contact tip to
work distance gives the correct electrical stickout
as required for the procedure being used.
NOTE: If the arc voltage is not within the proper
procedure range adjust the power source output
control. (The CC mode WIRE SPEED setting should
not be changed from the preset procedure value for
the proper arc voltage.)
d. To stop welding, release the gun trigger and
then pull the gun away from the work. Store the
gun in the LN-25 insulated gun holder when
not welding.
LN-25
LN-25
B-9
B-9
OPERATION
Do not use LN-25 models below Code 9200 with
any TIG or Square Wave welding power sources.
Do not use LN-25 models equipped with internal
contactors with non-Lincoln TIG or Square Wave
welding power sources. Damage to the LN-25 circuit
can occur as a result of the high output inductance
typically associated with these power sources. TIG
high frequency power should never be applied to
the LN-25.
While welding with a continuously fed electrode,
weld current variations are continuously taking place.
There are many causes for these variations, but
predominantly they occur due to changes in
electrical stick out (operator hand movements,
nozzle tip contact variations, etc.) and the dynamic
metal transfer characteristics of the process or
procedure being used (short arc, globular transfer,
etc.).
When using a CV power source, these current
variations have essentially no effect on the welding
arc stability since CV power sources can provide a
wide range of weld current levels with virtually no
change in average arc voltage. These “flat slope” CV
power sources, therefore, provide the arc power
required to produce the best welding characteristics
and ease of operation for most open arc, constant
wire feed speed, welding processes.
CC (formerly VV) power sources, on the other hand,
permit the arc voltage to decrease with increases in
welding current. The output characteristics of these
power sources can range from a “drooping slope,”
which provide minor arc voltage changes with weld
current variations, to “steep slope” which provide
broad voltage changes with only minor current
variations. The steeper the slope the more difficult it
becomes to maintain arc voltage stability with a
constant wire speed open arc process.
To aid in stabilizing the arc voltage when welding on
CC power sources the LN-25 is provided with a VV
(CC) wire feed mode. This arc voltage sensing feed
mode decreases (or increases) the wire speed when
the arc voltage decreases (or increases). However,
if the electrode shorts to the work, the arc voltage
will essentially drop to zero and the short circuit
current supplied by the CC power source may not
provide enough power to re-establish the arc
(especially with steeper slope machines). Under this
condition the LN-25 feeder will stop, as if the trigger
was released, and not restart until the short has
been opened.
Arc shorting is more difficult to avoid when using
a CC power source, and requires a more refined
operator technique than when using a CV power
source. Improved performance can be obtained
on CC power source applications within the
following guidelines:
1. Flatter slope power sources with higher arc
force (short circuit current) will improve
performance over steep slope machines. The
steeper the slope, the more critical it is to hold
proper electrode stick out to maintain arc
stability. Welding techniques, such as weaving,
will be more difficult to control. Use the highest
output current tap or setting capable of providing
the voltage adjustment required for the
procedure.
2. Use spray or non-shorting small ball type
transfer processes at higher procedure voltage
levels. Generally, open arc processes with
procedure voltage levels over 22 volts perform
satisfactorily. Arc stability at procedure voltage
levels below 22 volts may be more difficult to
control, with the general exception of fine (.023—
.035) solid steel electrodes with Argon-rich
shielding gas or NR-152 and NR-211 Innershield.
CAUTION
AUTOMATIC PROTECTION
SHUTDOWN
The LN-25 control provides automatic electronic
protection circuits which shut down the LN-25 for
excessively high power source open circuit voltage
or excessive motor overload.
OVERVOLTAGE SHUTDOWN
If the power source open circuit voltage exceeds
about 110-120 volts, the LN-25 will not operate until
the power source voltage drops below about 102-
110 volts.
MOTOR OVERLOAD SHUTDOWN
If excessive motor overload occurs (due to prolonged
excessive feeding force, jammed drive rolls or
shorted motor leads), the LN-25 will shut down within
a few seconds after the overload occurs.
The shutdown will reset automatically when the gun
trigger is released, but will reoccur if the overload
situation is not remedied.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38

Lincoln Electric LN-25 Mode d'emploi

Catégorie
Système de soudage
Taper
Mode d'emploi

dans d''autres langues