GE Profile 1088951 Manuel utilisateur

Refrigerators

Bottom Freezer

239D4106P022 49-60748 02-16 GE

Write the model and serial

numbers here:

Model # ____________________

Serial # ____________________

Find these numbers on a label

on the left side, near the middle

of the refrigerator compartment.

GE and GE Profile™ models

Models that start with PFE, GFE, DFE, PFH,

and GNE are Standard Depth Models (SD)

Models that start with DYE, GYE, PYE and

PWE are Counter Depth Models (CD)

Owner’s Manual and

Installation Instructions

*Select Models Only

Modèles GE et GE Profile™

Manuel d’utilisation

et instructions

d’installation

Les numéros de modèle commençant par PFE, GFE,

DFE, PFH, et GNE sont des modèles

de profondeur normale (PN).

Les numéros de modèle commençant par DYE, GYE,

PYE et PWE sont des modèles de profondeur

de comptoir (PC).

Réfrigérateurs

GE y GE Profile™ modelos

Manual del Propietario e

Instrucciones de Instalación

Los modelos que comienzan con las letras

DFE, PFE, GFE, DFE, PFH, y GNE son Modelos

con Profundidad Estándar (SD)

Los modelos que comienzan con las

letras GYE, PYE y PWE son Modelos con

Profundidad de Mesada (CD)

Refrigeradores

Safety Instructions ............2, 4

Operating Instructions

Features ..........................5, 6

Controls ........................7–10

Dispenser* .........................11

Autofill* ............................12

Single Serve Brewer* ...............13

About Appliance Communication . . .14

Water Filter ........................15

Fresh Food Storage Options .....16,17

Climate Zone & Temperature

Controlled Drawer ...............18,19

Freezer ............................20

Automatic Ice maker ...............21

Care and Cleaning ................ 22

Replacing the Lights ................23

Installation Instructions

Preparing to Install the

Refrigerator .................24, 25

Installing the Refrigerator .......26-37

Installing the Water Line ........38-40

Troubleshooting Tips ......42-44

Normal Operating Conditions .......41

Truth or Myth ...................45 46

Consumer Support

Warranty ..........................47

RPWFE Water Filter Cartridge Limited

Warranty .........................48

Performance Data Sheet ...........49

Consumer Support .................50

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

2

GE Appliances website

For more information on your refrigerator’s operation, visit

www.GEAppliances.com

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety

messages will follow the safety alert symbol and the word “DANGER”, “WARNING”, or “CAUTION”. These words are defined as:

Indicates a hazardous situation which, if not avoided, will result in death or serious injury.

Indicates a hazardous situation which, if not avoided, could result in death or serious injury.

Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

REFRIGERATOR SAFETY INFORMATION

SAFETY

WARNING

DANGER

CAUTION

IMPORTANT SAFETY INSTRUCTIONS

To reduce the risk of fire, explosion, electric shock, or injury when using your

refrigerator follow these basic safety precautions:

WARNING

 Do not clean glass shelves or covers with warm water when

they are cold. Glass shelves and covers may break if exposed

to sudden temperature changes or impact, such as bumping

or dropping. Tempered glass is designed to shatter into many

small pieces if it breaks.

 Keep fingers out of the “pinch point” areas; clearances

between the doors and between the doors and cabinet are

necessarily small. Be careful closing doors when children are in

the area.

 Do not touch the cold surfaces in the freezer compartment

when hands are damp or wet, skin may stick to these

extremely cold surfaces.

 Do not refreeze frozen foods which have thawed completely.

 In refrigerators with automatic icemakers, avoid contact with

the moving parts of the ejector mechanism, or with the heating

element that releases the cubes. Do not place fingers or hands

on the automatic ice making mechanism while the refrigerator

is plugged in.

To reduce the risk of injury when using your refrigerator, follow these basic

safety precautions.

 This refrigerator must be properly installed and located in

accordance with the Installation Instructions before it is used.

 Unplug the refrigerator before making repairs, replacing a light

bulb, or cleaning.

Note: Power to the refrigerator cannot be disconnected by any

setting on the control panel.

Note: Repairs must be performed by a qualified service

professional.

 Replace all parts and panels before operating.

 Do not store or use gasoline or other flammable vapors and

liquids in the vicinity of this or any other appliance.



Because of potential safety hazards under certain conditions,

we strongly recommend against the use of an extension cord.

However, if you must use an extension cord, it is absolutely

necessary that it be a UL-listed (in the United States) or a CSA

certified (in Canada), 3-wire grounding type appliance extension

cord having a grounding type plug and outlet and that the electrical

rating of the cord be 15 amperes (minimum) and 120 volts.

 To prevent suffocation and entrapment hazards to children,

remove the fresh food and freezer doors from any refrigerator

before disposing of it or discontinuing its use.

 Do not allow children to climb, stand or hang on the door

handles or the shelves in the refrigerator. They could seriously

injure themselves.

CAUTION

3

GEAppliances.com

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.

For personal safety, this appliance must be properly grounded.

The power cord of this appliance is equipped with

a 3-prong (grounding) plug which mates with a

standard 3-prong (grounding) wall outlet to minimize

the possibility of electric shock hazard from this

appliance.

Have the wall outlet and circuit checked by a

qualified electrician to make sure the outlet is

properly grounded.

Where a standard 2-prong wall outlet is encountered,

it is your personal responsibility and obligation to

have it replaced with a properly grounded 3-prong

wall outlet. Do not use an adapter.

The refrigerator should always be plugged into its

own individual electrical outlet which has a voltage

rating that matches the rating plate.

A 115 Volt AC, 60 Hz, 15- or 20-amp fused, grounded

electrical supply is required. This provides the best

performance and also prevents overloading house

wiring circuits which could cause a fire hazard from

overheated wires.

Never unplug your refrigerator by pulling on the

power cord. Always grip plug firmly and pull straight

out from the outlet.

Repair or replace immediately all power cords that

have become frayed or otherwise damaged. Do not

use a cord that shows cracks or abrasion damage

along its length or at either end.

When moving the refrigerator away from the wall, be

careful not to roll over or damage the power cord.

CONNECTING ELECTRICITY

WARNING

Electrical Shock Hazard.

Plug into a grounded 3-prong outlet

Do not remove the ground prong

Do not use an adapter

Failure to follow these instructions can result in death, fire, or electrical shock.

WARNING

Explosion Hazard.

Keep flammable materials and vapors, such as gasoline, away from refrigerator. Failure to do so can

result in fire, explosion, or death.

INSTALLATION

SAFETY (CONT.)

WARNING

Tip Over Hazard.

Built-in style models (model PYE, CYE, GYE, DYE, PWE, CWE, and ZWE) are top heavy, especially

with any doors open. These models must be secured with the anti-tip floor bracket to prevent

tipping forward, which could result in death or serious injury. Read and follow the entire installation

instructions for installing the anti-tip floor bracket packed with your refrigerator.

WARNING

Scalding Hazard.

The hot water dispenser is capable of heating water to a temperature of approximately 185°F (85°C).

Water temperatures above 125°F (52°C) can cause severe burns or death from scalding. Children, the

disabled, and the elderly are at highest risk of being scalded.

Use this appliance only for its intended purpose as described in this Owner’s Manual. To reduce the risk of severe burns,

scald injuries, or death when using your hot water dispenser, the instructions below must be followed:

HOT WATER DISPENSER

 Do not permit children to use the hot water dispenser.

 The water coming from the dispenser is very hot. Use

extreme caution when dispensing and drinking water. Allow

water to cool to a drinkable temperature before drinking.

 When dispensing water below 125ÛF, always test the

temperature of the water before drinking.

 When dispensing hot water, the container can become

very hot. Use a temperature insulating container, such as

ceramic or foam. Using container materials such as paper

or plastic may result in a burn while holding the cup. Do

not use glass containers, as thermal shock can cause the

container to break and may result in scalding or lacerations.

 Do not use with water that is microbiologically unsafe or of

unknown quality.

 Your container should be close to the dispensing point to

minimize the splashing of hot water.

 A newly installed water filter cartridge will cause water to

spurt from the dispenser. Run 2 gallons of water through

the cold water dispenser (about 5 minutes) to remove air

from the system. Until this air is removed from the system

through the cold water dispenser, DO NOT use the hot

water dispenser as it may result in spurting of hot water and

lead to hot water scalding.

 The first time the hot water feature is used, confirm if

you live above 5000 feet (high altitude). This limits the

temperature of the hot water system to avoid boiling. To

access the high altitude selection, press Fridge and Door

Alarm and control will cycle from Hi AL to Lo AL (high

altitude to low altitude).

 The hot water dispenser is designed to only dispense water.

Do not attempt to heat or dispense anything other than

water. Do not attempt to disassemble or clean the tank.

 The hot water dispensing tank is a non-pressurized tank,

with a vent on the tank and a dispenser tube outlet. Do

not modify the system, close or block the dispense tube, or

connect any other type of device to the tank or dispense

tube. Doing so may lead to rupture of the tank and hot

water scalding.

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

4

SAFETY

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

WARNING

Suffocation and child entrapment hazard.

Remove fresh-food and freezer doors from the refrigerator, prior to disposal. Failure to do so can

result in child entrapment which can lead to death or brain damage.

Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are

still dangerous even if they will sit for “just a few

days.” If you are getting rid of your old refrigerator,

please follow the instructions below to help prevent

accidents.

Before You Throw Away Your Old Refrigerator or

Freezer:

 Take off the fresh food and freezer doors.

 Leave the shelves in place so that children may

not easily climb inside.

Refrigerants

All refrigeration products contain refrigerants,

which under federal law must be removed prior

to product disposal. If you are getting rid of an old

refrigeration product, check with the company

handling the disposal about what to do.

PROPER DISPOSAL OF YOUR OLD REFRIGERATOR

IMPORTANT:

Space-saving ice maker*

Ice maker and bin are located on the door creating

more usable storage space.

Showcase LED lighting

LED lighting is positioned throughout the interior to

spotlight areas in the refrigerator. LEDs are located

under the fresh food door to light the freezer when

opened.

Drop-down tray*

Allows for extra door storage when you need it and

tucks away when you don’t.

Full-width temperature controlled drawer*

Adjustable temperature control bin that can

accommodate larger items.

Dairy bin*

Separate compartment for your items.

Freezer ice maker/Ice bin*

An ice maker in both compartments gives you more

ice whenever you need it. Available on Non-Dispense

models, also available as a kit for some models.

QuickSpace™ shelf*

Functions as a normal full-sized shelf when needed

and easily slides back to store tall items below.

Spillproof shelves

Designed to capture your spills for easier clean up.

Anti-slip Mat*

Liner that captures spills, keeps containers from

shifting when the door is opened and is easily

removable for cleaning.

Removable door bin

Can be removed for those with a wall limiting the door

opening.

Climate zone bin

Separate bins for produce storage.

Water filter

Filters water & Ice

5

About the features. * GEAppliances.com

*Select Models Only

6

Door ice bin*

1. Open left fresh food door.

2. Pull down latch to release bin door.

3. Using handhold lift ice bucket up

and out to clear locators in bottom

of bin.

4. To replace the ice bucket, set it on

the guide brackets and push until

the ice bucket seats properly.

5. If bucket cannot be replaced,

rotate the Ice Bucket Fork 1/4 turn

clockwise.

Drop down dairy bin*

1. Open right fresh food

2. Depress both buttons on lower sides

and bin will drop down.

3. Reverse to reinstall.

Ice/water filter

Remove filter/bypass plug

Push the indent on the cover and pull

open filter door fully. Rotate the filter/

bypass plug as far as it will go and pull

the filter/bypass plug toward you to

remove.

Installing the filter cartridge

Push the new filter/bypass plug straight

in aligning the lugs with the notches

in cabinet and rotate the filter/bypass

plug into the recess in the cabinet. Make

sure the front of the filter is toward the

interior of the refrigerator.

Close the cover making sure the indent

snaps into position.

Drop down tray

(tray open)

Ice bucket

Latch

About the features.*

*Select Models Only

Push in and

pull open

Swing

Push \ Pull

1

2

WARNING

Scalding Hazard.*

Use of the hot water dispenser prior to purging

air from the system may result in spurting of hot

water and lead to hot water scalding. Follow the

instructions for “Water Filter - Step 3” on page

15 to purge all air from the system through the

cold water dispenser prior to using the hot water

dispenser.

The first time the hot water feature is used,

confirm if you live above 5000 feet (high

altitude). This limits the temperature of the

hot water system to avoid boiling. To access

the high altitude selection, see About the

controls-features.

Filter Bypass Plug

To reduce the risk of property damage due to

water leakage, you MUST use the filter bypass

plug when a replacement filter cartridge is not

available. The dispenser and icemaker will not

operate without either the filter or bypass plug

installed. The bypass plug is installed in the same

way as a filter cartridge.

About the controls with temperature settings. GEAppliances.com

The temperature controls are preset in the factory at 37°F for the refrigerator compartment and 0°F for the freezer

compartment. Allow 24 hours for the temperature to stabilize to the preset recommended settings.

Control Style D: The temperature controls can display both the SET temperature as well as the actual temperature in the

refrigerator and freezer. The actual temperature may vary slightly from the SET temperature based on usage and operating

environment (PWE23 and GNE29 only).

NOTE: The refrigerator is shipped with protective film covering the temperature controls.

If this film was not removed during installation, remove it now.

PFE28P, PYE22P Control Style A, Single Serve Models

PFH28, PFE28K, DFE28, PYE22K, DYE22 Control Style B,

AutoFill Models

GFE28, GFE26, GYE22 Control Style C, GE Models

GNE29, PWE23 Control Style D, Non-Dispense Control

Refrigerator

Hold 3 Sec for °F/°C

Hold 3 Seconds

Recommended: 37 °F

Actual Set

Freezer

Door Alarm

Ice Maker

Lock Controls

Reset Filter

Recommended: 0°F

F

7

Ice

Error

Complete

Sensing

Cubed

Crushed

8

About the controls with temperature settings.

NOTE: For optimal temperature performance, we recommend to avoid placing food items directly at the air flow vents of the

fresh food air tower and thus blocking the air flow.

Changing the Temperature for Control Style A

To Change the Refrigerator Temperature:

Press the Fridge button and current set temperature will

display. Pressing and releasing the button will cycle through

the available temperature settings. Press and hold button for

Turbo Cool feature. The display will show tC.

To Change the Freezer Temperature:

Press the Freezer button and current set temperature will

display. Pressing and releasing the button will cycle through

the available temperature settings. Press and hold button for

Turbo Freeze feature. The display will show tF.

Cooling system can be turned off by pressing and holding

Freezer and Start Heating. OFF will be displayed. To turn on,

press Fridge or Freezer. ON will be displayed.

Turning the cooling system off stops the cooling to the

refrigerator, but it does not shut off the electrical power.

Changing the Temperature for Control Styles B and C

To change the temperature, press and release the Freezer

or Fridge pad. The display will show the set temperature. To

change the temperature, press either the Freezer or Fridge

pad until the desired temperature is displayed. Press and

hold button for Turbo Cool feature. The display will show tC.

Press and hold button for Turbo Freeze feature. The display

will show tF.

To turn off the cooling system press and hold the Fridge and

Ice Maker buttons. To turn on, press Fridge or Freezer.

Turning the cooling system off stops the cooling to the

refrigerator, but it does not shut off the electrical power.

Changing Temp. for Control Style D

Temperature Display is located on inside of left-hand

refrigerator door. To change the temperature, press and

release the REFRIGERATOR or FREEZER pad. The ACTUAL

TEMP light will come on and the display will show the

actual temperature. To change the temperature, tap

either the REFRIGERATOR or FREEZER pad until the desired

temperature is displayed.

To turn OFF cooling system, press and hold the

REFRIGERATOR and FREEZER pads simultaneously for

3 seconds. When cooling system is OFF the display

should read OF. To turn ON cooling system, press either

REFRIGERATOR or FREEZER pad. The display will show the

preset temperature settings of 37°F for refrigerator and 0°F

for freezer.

Turning the cooling system off stops the cooling to

refrigerator, but it does not shut off the electrical power.

Ice

9

Hands-free Autofill*

Hands-free Autofill uses sensors to monitor container height

to automatically dispense filtered water without having to

activate the paddle.

Start Heating*

The Start Heating button is used to initiate the water heating

for the Single Serve feature. To abort the Start Heating

feature, press and hold the Start Heat button for 3 seconds.

Freezer temp control

Adjust freezer compartment temperature.

Fresh food temp control

Adjust fresh food compartment temperature.

TurboFreeze™ setting

Activate TurboFreeze to quickly restore freezer temperatures

after frequent door openings.

TurboCool™ setting

Activate TurboCool to quickly restore fresh food temperature

after frequent door openings.

Lock Controls

Control Style A - Press and hold the Door Alarm pad for 3

seconds to lock out ice and water dispenser and all feature

and temperature buttons.

Control Styles B & C -

Press Lock pad and hold 3 seconds

to lock out ice and water dispenser and all feature and

temperature buttons.

Dispenser light

Lighting that can be turned on/off to light your dispenser.

Door Alarm

Sounds to alert when the freezer or fresh food doors have

been left open. Press and hold Door Alarm pad and it will

toggle the sound between low, high, and off.

Brew Size*

The Brew Size button is used to select the desired cup size

for single serve. Press and hold the button for 3 seconds to

toggle the brew type between Coffee and Cocoa.

Ice maker setting

Turn your ice makers on/off.

Cooling system On/Off

Control Style A - Press and hold Freezer and Start Heating

simultaneously to turn cooling system off. To turn cooling

system on press either the Fridge or Freezer.

Control Style B & C - Press and hold Fridge and Ice Maker

simultaneously for 3 seconds to turn the cooling system off.

To turn cooling system on press either the Fridge or Freezer.

Brew Dispense

Press and hold Brew Dispense button for 3 seconds, but no

longer than 6 seconds, to dispense coffee or cocoa.

F°/C°

Control Style A - Press and hold Freezer and Brew Size to

switch between F°/C°.

Control Style B & C - Press and hold Ice Maker and Door

Alarm simultaneously for 3 seconds to switch between F°/C°.

Sound Control for pad chimes

Control Style A - Press and hold the Light pad: Once for High

to Off, twice for Off to Low and three times for Low to High.

Control Styles B & C - Press and hold the Door Alarm pad:

Once for High to Off, twice for Off to Low and three times for

Low to High.

High Altitude

Control Style A (PYE and PFE only) - Press and hold Fridge

and Door Alarm for to toggle between Hi Al and Lo AL for

high altitude and low altitude.

Additional settings:

• Connected Home ready* (PFE28P, PYE22P, PFH only)

• Water Filter* - An indicator will illuminate when the filter needs

to be replaced. When a new filter is installed the indicator will go

off.

Additional Mode:

• Sabbath Mode

Control Style A - Press and hold Alarm and Light

simultaneously for 3 seconds to enter/exit Sabbath mode.

Control Style B & C - Press and hold Lock and Light

simultaneously for 3 seconds to enter/exit Sabbath mode.

Activate Sabbath Mode to turn off interior lights, temperature

control and advanced features. Compressor will run on a timed

defrost when in Sabbath mode.

Control Style A, External Controls

PFE28P,

PYE22P

About the controls - features. GEAppliances.com

Control Style B, External Controls

PFH28, PFE28K, DFE28,

PYE22K, DYE22

Control Style C, External Controls

GFE28, GFE26,

GYE22

*Select Models Only

Error

Complete

Sensing

Cubed

Crushed

10

About the controls - features.

Refrigerator

Hold 3 Sec for °F/°C

Hold 3 Seconds

Recommended: 37 °F

Actual Set

Freezer

Door Alarm

Ice Maker

Lock Controls

Reset Filter

Recommended: 0°F

F

Controls Style D, Internal Controls

GNE29, PWE23

Door Alarm

Sounds to alert when the freezer or fresh food doors

have been left open.

Reset Filter

Hold for 3 seconds after replacing filter.

Lock Controls

Press and hold 3 seconds to lock out ice and water dis-

penser and all feature and temperature buttons.

Freezer temp control

Adjust freezer compartment temperature

Refrigerator temp control

Adjust fresh food compartment temperature

Ice maker setting

Turn your ice maker on/off.

11

About the dispenser.* GEAppliances.com

Dispenser tray

Important Facts About Your Dispenser



Do not add ice from trays or bags to the door ice maker

bucket. It may not crush or dispense.



Avoid overfilling glass with ice and use of narrow glasses.

Backed-up ice can jam the chute or cause the door in the

chute to freeze shut. If ice is blocking the chute remove the ice

bucket, poke it through with a wooden spoon.



Beverages and foods should not be quick-chilled in the

door ice maker bin. Cans, bottles or food packages in the

storage drawer may cause the ice maker or auger to jam.



To keep dispensed ice from missing the glass, put the glass

close to, but not touching, the dispenser opening.



Some crushed ice may be dispensed even though you

selected CUBED ICE. This happens occasionally when a few

cubes accidentally get directed to the crusher.



After crushed ice is dispensed, some water may drip from the

chute.



Sometimes a small mound of snow will form on the door in the

ice chute. This condition is normal and usually occurs when you

have dispensed crushed ice repeatedly. The snow will eventually

evaporate.

If no water is dispensed when the refrigerator is first installed,

there may be air in the water line system. Press the dispenser

paddle for at least five minutes to remove trapped air from the

water line and to fill the water system. To flush out impurities in

the water line, throw away the first six full glasses of water.

To remove Dispenser Tray (Type A and B Only)



Pull Dispenser Tray out until it stops.



Locate tab in the center on the bottom and push up.



Pull Dispenser Tray assembly out.



Lift Dispenser Tray out at center notch to clean.

To remove Dispenser Tray (Type C Only)



Grasp Dispenser Tray and pull firmly until it comes out.

To reinstall Dispenser Tray (Type A and B Only)



Place the Dispenser Tray cover on top of catch tray and

position under the two plastic retainers on either side.



Center Dispenser tray, and align with center guides.



Push in until it locks firmly in place.

To reinstall Dispenser Tray (Type C Only)



Line up the guide on tray bottom with track on dispenser and

slide it in until it stops against the back of the dispenser.

Water & Ice Dispenser

(See About the controls

with temperature settings &

About the control features)

To Use the Internal Water Dispenser*

The water dispenser is located on the

left wall inside the refrigerator compart-

ment.

To dispense water:

Hold the glass against the recess.

Push the water dispenser button.

Hold the glass underneath the

dispenser for 2–3 seconds after

releasing the dispenser button. Water

may continue to dispense after the

button is released.

If no water is dispensed when the refrigerator is first installed,

there may be air in the water line system. Press the dispenser

button for at least 5 minutes to remove trapped air from the

water line and to fill the water system. During this process,

the dispenser noise may be loud as the air is purged from the

water line system. To flush out impurities in the water line,

throw away the first 6 glassfuls of water.

NOTE: To avoid water deposits, the dispenser should be

cleaned periodically by wiping with a clean cloth or sponge.

WARNING

Laceration Hazard

 Never put fingers or any other object into ice crusher

discharge opening. Doing so can result in contacting the ice

crushing blades and lead to serious injury or amputation

 Use a sturdy glass when dispensing ice. A delicate glass may

break and result in personal injury.

*Select Models Only

To Use HANDS FREE AUTOFILL:

• Center container on Recess Dispenser Tray as far back as

possible without activating paddle and remove hand from

container

• Press AUTOFILL

To Stop AUTOFILL

• Press AUTOFILL to stop.

Important Facts about AUTOFILL

• For optimum results, use a uniform container between

4-8” tall and 2-6” wide.

• Fill level and functionality may vary on containers taller

than 8” or wider than 6”.

• Container volumes may vary, if error message “Not Found”

is given, try a different container.

• AUTOFILL will time out.

• Handles, straws, and garnishes on the rim of the container

my cause overfilling or variation in fill volumes.

• Splashing may occur depending on the location of the

container, water flow rate, container shape, and ice cubes.

• Keep sensors clean with a clean damp cloth, and do not

spray liquid or cleaners directly on sensors

• AUTOFILL works best with household water pressure of 60

to 100 psi.

• Ice in container may affect fill volume. If issues are

experienced, use less ice.

12

About Autofill.*

Sensors

*Select Models Only

About the K-Cup Brewing System.*

WARNING

Scalding Hazard.

• The water coming from the dispenser is very hot and can

cause scalds or burns. Read all warnings on page 4 prior

to use.

• Do not permit children to use the brewer.

• Always use a container that is suitable for hot liquids

(ceramic, foam, etc.)

• Do not brew into a mug made of glass. Doing so may

cause the glass to crack or break.

• If you live above 5000 feet, press Fridge and Door Alarm

and control will cycle from Low Altitude (Lo AL) to High

Altitude (Hi AL).

• DO NOT use the hot water dispenser immediately after

installing a new water filter as it may result in spurting

of hot water. Dispense cold water for about 5 minutes to

purge air from the system prior to dispensing hot water.

Important Facts about HOT WATER

*Select Models Only

About the K-Cup Brewing System.* (Cont)

GEAppliances.com

13

Push to

open

1

2

3

Load the K-Cup Brewer

Insert a Keurig K-Cup pod into the brewer and press down

firmly (you will hear a popping sound).

Two Ways To Brew

1. Press the Start Heating button.

OR

2. Initiate heating with the GE Kitchen App. Download the App

“GE Kitchen”. Visit www.GEAppliances.com/connect for

more information.**

CAUTION

Cut/Puncture Hazard.

•

There are two sharp needles located inside the

K-Cup brewer. To avoid risk of injury, do not put

your fingers inside the brewer. Use caution when

cleaning.

•

Keep the K-Cup brewer out of the reach of children,

as they may be injured in using the K-Cup brewer

incorrectly.

4

Dispense

Once the heating process is complete, the Dispense light on the display will flash.

To dispense, slide the brewer into the rails. Make sure the brewer is pushed all the way into the bracket. Place your

mug on the drip tray mug icon, under the red brew spout. Press and hold Brew Dispense for 3 seconds until you

hear the dispenser engage.

Cleaning the brewer



The K-Cup brewer is top rack dishwasher safe.



It is recommended to rinse it thoroughly after washing to remove all soap residue.



Periodic cleaning of dispenser recess area is recommended as staining may occur with usage of the

K-Cup brewer.

K-Cup

Close the

brewer.

Lid will

click when

secure.

Change Brew Size

Press the Brew Size button any time during the heating cycle to

choose 6, 8, or 10 oz. The default size is 8 oz. Ensure the mug being

used is large enough for the size selected.

NOTE: Press and hold the Brew Size button for 3 seconds to toggle

between Coffee and Cocoa. The default is Coffee.

NOTE: To abort the heating cycle, press and hold the Start

Heating button for 3 seconds. To abort the brew dispense cycle,

press and hold the Start Heating button for 3 seconds, press the

paddle, press any button on the display besides Brew Size or Brew

Dispense, or open the right fresh food door.

Red brew

spout for mug

alignment

Mug icon for

placement

Rails for

the brewer

** For US and US Territories Only.

14

Appliance Communication

GE WiFi Connect (for customers in the United States)

GE WiFi Connect Enabled* (PFE28P PYE22P, PFH models only)

Y

If your refrigerator has a Connected Appliance information label located on

the inside as shown, your refrigerator can be connected to your WiFi network,

allowing it to communicate with your smart phone for remote monitoring, control

and notifications. Depending on the refrigerator model you have, you either have

a WiFi communication card built into the product, or a port for an external WiFi

ConnectPlus Module (sold separately). Please visit www.GEAppliances.com/

connect to learn more about connected appliance features, and to learn what

connected appliance apps will work with your Smart Phone.**

To use your WiFi, press Water and Light on the control panel.

REGULATORY INFORMATION

FCC/IC Compliance Statement:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of

the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/television technician for help.

Labelling: Changes or modifications to this unit not expressly approved by the manufacturer could void the user’s authority

to operate the equipment.

ConnectPlus module only (or similar communication module)

RF Exposure - This device is only authorized for use in a mobile application. At least 20 cm of separation distance between

the ConnectPlus device and the user’s body must be maintained at all times.

*Select Models Only

GE WiFi Connect Optional *

You refrigerator is GE WiFi Connect compatible using the GE ConnectPlus module that is provided with your

refrigerator. To connect this appliance to the internet you will need to attach the module to your appliance through

the communication port in the appliance. The GE ConnectPlus will allow your appliance to communicate with your

smart phone for remote appliance monitoring, control and notifications. Please visit www.GEAppliances.com/

connect to learn more about connected appliance features, to learn what connected appliance App’s will work with

your Smart Phone and to learn where you can purchase a GE ConnectPlus.**

WiFi Connectivity: For assistance with the appliance or the ConnectPlus network connectivity (for models that are WiFi

enabled or WiFi optional), please call 1-800-220-6899.

** For US and US Territories Only.

15

*Select Models Only

About the GE

®

RPWFE water filter cartridge. GEAppliances.com

Water Filter Cartridge

The water filter cartridge is located in the fresh food interior

on the left side wall, near the top.

This product uses radio frequency identification (RFID) to

detect leaks and monitor filter status. The RFID technology is

certified by the FCC.

When to replace the filter cartridge

The filter cartridge should be replaced every six months or

earlier if 170 gallons of water has been dispensed or the flow of

water to the dispenser or icemaker decreases.

Touch Screen Models: A filter status message will appear on

the screen when the water filter needs to be replaced. The filter

status will automatically update when the filter is replaced.

Non-touch Screen Models: A filter indicator light will illuminate

on the screen when the water filter needs to be replaced.

Removing the filter cartridge

To replace the filter, first remove the old cartridge by opening

the filter door and pulling on the bottom of the cartridge to allow

it to swing outward. When the cartridge can no longer swing,

gently pull to unseat it from the cartridge holder. DO NOT TWIST

CARTRIDGE. A small amount of water may drip out.

Installing the Filter Cartridge

1. Align top of filter cartridge with cartridge holder with the word

“FRONT” facing outward then push the cartridge toward

the rear of the unit until it is fully seated. DO NOT TWIST THE

FILTER CARTRIDGE!

2. While continuing to ensure cartridge is fully seated in the

holder, gently swing the filter inward until it is in position. If

filter will not swing easily, check to ensure filter is properly

aligned and fully seated within the cartridge holder. Close the

filter door.

3. Run two gallons of water through the cold water dispenser

(about 5 minutes) to remove air from the system. A newly

installed filter cartridge will cause water to spurt from the

dispenser. Use a large pitcher or sports bottle to catch the

water spray. DO NOT use hands-free auto-fill (some models)

until all air is removed from the system.

4. Reset Filter Status message (non-touch screen models).

WARNING

Scalding Hazard.*

Use of the hot water dispenser prior to purging air from the

system may result in spurting of hot water and lead to hot water

scalding. Follow the instructions above to purge all air from the

system through the cold water dispenser prior to using the hot

water dispenser.

Note: It is normal for water to appear discolored during the initial

system flush. Water color will return to normal after first few

minutes of dispensing.

Filter Bypass Plug

To reduce the risk of property damage due to water leakage,

you MUST use the filter bypass plug when a replacement filter

cartridge is not available. The dispenser and icemaker will not

operate without either the filter or bypass plug installed. The

bypass plug is installed in the same way as a filter cartridge.

FCCID: ZKJ-EBX1532P001 ICID: 10229A-EBX1532P001

“This device complies with part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause

undesired operation.”

“This device complies with Industry Canada licence-exempt

RSS standard(s). Operation is subject to the following two

conditions: (1) this device may not cause interference, and (2)

this device must accept any interference, including interference

that may cause undesired operation of the device.”

WARNING

To reduce the risk associated with choking, do not allow children under 3 years of age to have access to small parts

during the installation of this product. The disposable filter cartridge should be replaced every 6 months at the rated capacity,

or sooner if a noticeable reduction in flow rate occurs.

For the maximum benefit of your filtration system, GE recommends the use of GE-branded filters only. Using GE-branded filters

in GE and Hotpoint

®

refrigerators provides optimal performance and reliability. GE filters meet rigorous industry NSF standards

for safety and quality that are important for products that are filtering your water. GE has not qualified non-GE-branded filters

for use in GE and Hotpoint refrigerators and there is no assurance that non-GE-branded filters meet GE’s standards for quality,

performance and reliability.

If you have questions, or to order additional filter cartridges, visit our website at www.geapplianceparts.com or call GE

Parts and Accessories, 800.626.2002.

Customers in Canada should consult the yellow pages for the nearest Camco Service Center.

Swing

Push \ Pull

16

Rearranging the Shelves

To remove:

Remove all items from the shelf.

Tilt the shelf up at the front.

Lift the shelf up at the back and bring the

shelf out.

To replace:

While tilting the shelf up, insert the top hook

at the back of the shelf in a slot on the

track.

Lower the front of the shelf until the bottom

of the shelf locks into place.

Spillproof Shelves

Spillproof shelves have special edges to help

prevent spills from dripping to lower shelves.

Shelves in the refrigerator compartment are adjustable.

Quick Space Shelf *

This shelf splits in half and slides under itself for

storage of tall items on the shelf below.

This shelf can be removed and replaced or

relocated (just like spillproof shelves).

NOTE: The location of the upper Quick Space

Shelf is not adjustable.

About the fresh food storage options.

*Select Models Only

17

GEAppliances.com

Non-Adjustable Bins on the Door (Dispenser Models - Left Hand Door)

To remove: Lift the bin straight up, then pull out.

To replace: Engage the bin in the molded

supports on the door and push down. It will lock

in place.

The ice maker door bins are not

interchangeable, note the location upon

removal and replace the bin in its proper

location.

Adjustable Bins on the Door

Adjustable bins can easily be carried from

refrigerator to work area.

To remove: Lift bin straight up, then pull out.

To replace or relocate: Slide in the bin just

above the molded door supports, and push

down. The bin will lock in place. See page 36.

Drop down tray *

(tray open)

1. Open right fresh food

door

2. Depress both buttons

on lower sides of bin

and bin will drop down.

3. Reverse to reinstall.

Non-Adjustable Dairy Bin*

To remove: Lift the dairy bin straight up,

then pull out.

To replace: Engage the bin in the molded door

supports and push down. The bin will lock in

place. See page 36.

Non-Dispense Models

(Left Hand Door)

*Select Models Only

ClimateZone

Temperature Controlled Drawer*

The Temperature Controlled Drawer is a

full-width drawer with adjustable temperature

control. This drawer can be used for large

miscellaneous items.

To change setting, press select button.

Keep fruits and vegetables organized in separate

compartments for easy access.

Excess water that may accumulate in the bottom

of the drawers or under the drawers should be

wiped dry.

18

C

Fruits Vegetables

F

C

M

E

AT

DELI

P

R

O

DU

C

E

CH

E

SE

C

IT

R

U

S

SEL

E

C

T

ClimateZone

Fruits Vegetables

Fruits Vege

D

*Select Models Only

32° 34° 36°

Note: Temperatures indicate the appropriate tem-

peratures for the food and actual temperatures may

vary based on normal operation and other factors

such as door openings and fresh food set point.

CAUTION

Laceration Hazard.

Do not store glass bottles at this setting. If

they are frozen, they can break and result

in personal injury.

Meat Beverage Deli

Select

About the climate zone and temperature

controlled drawer.

GEAppliances.com

To remove:

Pull the drawer out to the stop position.

Lift the front of the drawer up and out.

To replace:

Pull left and right slides until fully

extended.

Place drawer back in first and rotate

drawer front down to seat on slide.

Push the drawer in to closed position.

How to Remove and Replace the Adjustable Deli/Produce Drawer

To remove:

Pull the drawer out to the stop position.

Raise the front side of the divider

to unhook it from the rear wall of

the drawer.

To replace:

Hook the back of the divider over the

rear wall of the drawer.

Push the divider down.

How to Remove and Replace Drawer Divider*

19

Divider

*Select Models Only

20

About the freezer.

Freezer Basket and Drawer

Basket.

Drawer

Ice Bucket * (Available on

Non-Dispense models only.

Available as a IM Kit on some

models)

Non-Adjustable Bin in the Freezer*

To remove: push in plastic tab on either left

or right side

To replace: slide bin into location until it

locks into place.

Basket Removal

To remove, standard depth models only:

Open freezer door to the stop position.

Remove freezer door bin by pushing

plastic tab on either left or right side

to release bin hinge pin.

Remove freezer basket by lifting up

the rear of the basket and moving

basket rearward until the front of the

basket can be rotated upward and

out.

Lift it out to remove.

To remove, counter depth models only:

Open fresh food doors.

Open freezer door to the stop position.

Remove freezer basket by lifting up

the rear of the basket and rotate it

upward.

Lift it out to remove.

To replace:

Reverse step 1 through 4 to replace.

*Select Models Only

La page charge ...

GE Profile 1088951 Manuel utilisateur

Ce manuel convient également à

GE Profile 1088951 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents