Yamaha RX-395 Manuel utilisateur
- Catégorie
- Tuners audio
- Taper
- Manuel utilisateur
Ce manuel convient également à
RX-495/395
OWNER’S MANUAL
MODE D’EMPLOI
MANUAL DE INSTRUCCIONES
Natural Sound Stereo Receiver
Ampli-syntoniseur stéréo de la série “Natural Sound”
Receptor estéreo de Sonido Natural
Thank you for selecting this YAMAHA stereo receiver.
Nous vous remercions pour avoir porté votre choix sur ce récepteur stéréo YAMAHA.
Muchas gracias por haber adquirido este receptor estéreo YAMAHA.
1 Read Instructions – All the safety and operating
instructions should be read before the unit is operated.
2 Retain Instructions – The safety and operating instructions
should be retained for future reference.
3 Heed Warnings – All warnings on the unit and in the
operating instructions should be adhered to.
4 Follow Instructions – All operating and other instructions
should be followed.
5 Water and Moisture – The unit should not be used near
water – for example, near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement, or near a swimming
pool, etc.
6 Carts and Stands – The unit should be used only with a
cart or stand that is recommended by the manufacturer.
6A A unit and cart combination should be
moved with care. Quick stops,
excessive force, and uneven surfaces
may cause the unit and
cart combination to overturn.
7 Wall or Ceiling Mounting – The unit should be mounted to
a wall or ceiling only as recommended by the
manufacturer.
8 Ventilation – The unit should be situated so that its
location or position does not interfere with its proper
ventilation. For example, the unit should not be situated
on a bed, sofa, rug, or similar surface, that may block the
ventilation openings; or placed in a built-in installation,
such as a bookcase or cabinet that may impede the flow
of air through the ventilation openings.
9 Heat – The unit should be situated away from heat
sources such as radiators, stoves, or other appliances
that produce heat.
10 Power Sources – The unit should be connected to a
power supply only of the type described in the operating
instructions or as marked on the unit.
11 Power-Cord Protection – Power-supply cords should be
routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying
particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the unit.
12 Cleaning – The unit should be cleaned only as
recommended by the manufacturer.
13 Nonuse Periods – The power cord of the unit should be
unplugged from the outlet when left unused for a long
period of time.
14 Object and Liquid Entry – Care should be taken so that
objects do not fall into and liquids are not spilled into the
inside of the unit.
15 Damage Requiring Service – The unit should be serviced
by qualified service personnel when:
A. The power-supply cord or the plug has been
damaged; or
B. Objects have fallen, or liquid has been spilled into the
unit; or
C. The unit has been exposed to rain; or
D. The unit does not appear to operate normally or
exhibits a marked change in performance; or
E. The unit has been dropped, or the cabinet damaged.
16 Servicing – The user should not attempt to service the unit
beyond those means described in the operating
instructions. All other servicing should be referred to
qualified service personnel.
17 Power Lines – An outdoor antenna should be located
away from power lines.
18 Grounding or Polarization – Precautions should be taken
so that the grounding or polarization is not defeated.
SAFETY INSTRUCTIONS
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead
symbol, within an equilateral triangle,
is intended to alert you to the
presence of uninsulated “dangerous
voltage” within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an
equilateral triangle is intended to alert
you to the presence of important
operating and maintenance
(servicing) instructions in the
literature accompanying the
appliance.
•
Explanation of Graphical Symbols
CAUTION
WARNING
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE THIS
UNIT TO RAIN OR MOISTURE.
2
1. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by
Yamaha may void your authority, granted by the FCC, to
use the product.
2. IMPORTANT : When connecting this product to
accessories and/or another product use only high quality
shielded cables. Cable/s supplied with this product
MUST be used. Follow all installation instructions.
Failure to follow instructions could void your FCC
authorization to use this product in the USA.
3. NOTE : This product has been tested and found to
comply with the requirements listed in FCC Regulations,
Part 15 for Class “B” digital devices. Compliance with
these requirements provides a reasonable level of
assurance that your use of this product in a residential
environment will not result in harmful interference with
other electronic devices.
This equipment generates/uses radio frequencies and, if
not installed and used according to the instructions
found in the users manual, may cause interference
harmful to the operation of other electronic devices.
Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this product
is found to be the source of interference, which can be
determined by turning the unit “OFF” and “ON”, please try
to eliminate the problem by using one of the following
measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the
antenna. If the antenna lead-in is 300 ohm ribbon lead,
change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Electronics
Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA
90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
Note to CATV system installer:
This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be
connected to the grounding system of the building, as
close to the point of cable entry as practical.
FCC INFORMATION (for US customers only)
SPECIAL NOTES FOR FCC COMPOSITE
DEVICE (for US customers only)
This device is a composite system. The digital device
component may not cause harmful interference.
19 For US customers only:
Outdoor Antenna Grounding – If an outside antenna is
connected to this unit, be sure the antenna system is
grounded so as to provide some protection against
voltage surges and built-up static charges. Article 810 of
the National Electrical Code, ANSI/NFPA 70, provides
information with regard to proper grounding of the mast
and supporting structure, grounding of the lead-in wire to
an antenna discharge unit, size of grounding conductors,
location of antenna discharge unit, connection to
grounding electrodes, and requirements for the grounding
electrode.
EXAMPLE OF ANTENNA GROUNDING
MAST
GROUND
CLAMP
ANTENNA
LEAD IN
WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810–20)
GROUNDING CONDUCTORS
(NEC SECTION 810–21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250. PART H)
ELECTRIC
SERVICE
EQUIPMENT
NEC – NATIONAL ELECTRICAL CODE
YAMAHA and the Electronic Industries Association’s
Consumer Electronics Group want you to get the most out of
your equipment by playing it at a safe level. One that lets the
sound come through loud and clear without annoying blaring
or distortion – and, most importantly, without affecting your
sensitive hearing.
Since hearing damage from loud sounds is often
undetectable until it is too late, YAMAHA and the
Electronic Industries Association’s Consumer
Electronics Group recommend you to avoid
prolonged exposure from excessive volume levels.
We Want You Listening For A Lifetime
(for US customers only)
3
English
●
RX-495
70W + 70W (8Ω) RMS Output Power,
0.04% THD, 20–20,000 Hz
RX-395
45W + 45W (8Ω) RMS Output Power,
0.04% THD, 20–20,000 Hz
●
High Dynamic Power, Low Impedance
Drive Capability
●
Continuously Variable Loudness Control
●
40-Station Random Access Preset Tuning
●
Automatic Preset Tuning
●
Preset Station Shifting Capability (Preset
Editing)
●
IF Count Direct PLL Synthesizer Tuning
System
●
SLEEP Timer
●
Remote Control Capability
●
RX-495 only
PURE DIRECT Switch to Reproduce the
Purest Source Sound
Safety Instructions.......................................... 2
Features ........................................................ 4
Supplied Accessories .................................... 4
Caution .......................................................... 5
Controls and Their Functions ........................ 6
Connections ................................................ 10
Basic Operations ......................................... 14
Tuning Operations ....................................... 17
Preset Tuning .............................................. 18
Notes about the Remote Control Transmitter
..................................................................... 21
Troubleshooting ........................................... 22
Specifications .............................................. 23
4
FEATURES CONTENTS
SUPPLIED ACCESSORIES
After unpacking, check that the following parts are contained.
RX-495
RX-395
Remote Control Transmitter AM Loop AntennaIndoor FM Antenna
Batteries (size AA, R6, UM-3) Antenna adapter
<U.S.A. and Canada model only>
5
English
CAUTION : READ THIS BEFORE OPERATING YOUR UNIT.
1 To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
2 Install this unit in a cool, dry, clean place – away from
windows, heat sources, sources of excessive vibration,
dust, moisture and cold. Avoid sources of humming
(transformers, motors). To prevent fire or electrical shock,
do not expose the unit to rain or water.
3 Do not operate the unit upside-down. It may overheat,
possibly causing damage.
4 Never open the cabinet. If something drops into the set,
contact your dealer.
5 The openings on the cabinet assure proper ventilation of
the unit. If these openings are obstructed, the
temperature inside the cabinet will rise rapidly. Therefore,
avoid placing objects against these openings, and install
the unit in well-ventilated condition. Make sure to allow a
space of at least 10 cm behind, on the both sides and
above the top panel of the unit. Otherwise it may not only
damage the unit, but also cause fire.
6 Do not use force on switches, controls or connection
wires. When moving the unit, first disconnect the power
plug and the wires connected to other equipment. Never
pull the wires themselves.
7 Do not attempt to clean the unit with chemical solvents;
this might damage the finish. Use a clean, dry cloth.
8 Always set the VOLUME control to “–
∞
” before starting
the audio source play. Increase the volume gradually to
an appropriate level after the play back has been started.
9 To prevent lightning damage, pull out the power cord and
remove the antenna cable during an electrical storm.
10 Be sure to read the “TROUBLESHOOTING” section
regarding common operating errors before concluding that
the unit is faulty.
11 AC outlet
Do not connect audio equipment to the AC outlet on the
rear panel if that equipment requires more power than the
outlet is rated to provide.
12 Voltage Selector (General Model only)
The voltage selector on the rear panel of this unit
must be set for your local main voltage BEFORE
plugging into the AC main supply.
Voltages are 110–120/220–240V AC, 50/60 Hz.
IMPORTANT
Please record the serial number of this unit in the space
below.
Serial No.:
The serial number is located on the rear of the unit.
Retain this Owner’s Manual in a safe place for future
reference.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
CAUTION (FOR CANADA MODEL)
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE
OF PLUG TO WIDE SLOT AND FULLY INSERT.
FOR CANADIAN CUSTOMER
THIS CLASS B DIGITAL APPARATUS MEETS ALL
REQUIREMENTS OF THE CANADIAN INTERFERENCE-
CAUSING EQUIPMENT REGULATIONS.
The apparatus is not disconnected from the AC power
source as long as it is connected to the wall outlet, even if
the apparatus itself is turned off.
FREQUENCY STEP switch (General Model only)
Because the interstation frequency spacing differs in
different areas, set the FREQUENCY STEP switch (located
at the rear) according to the frequency spacing in your area.
Before setting this switch, disconnect the AC power plug of
this unit from the AC outlet.
6
FRONT PANEL
RX-495
21A/B/C/D/E 3 4
PURE DIRECT
6578
TAPE 1TAPE 2
MONITOR
AUX PHONO
TUNER CD
POWER
TUNING MODE
AUTO/MAN'L MONO
FM/AM TUNING EDIT MEMORY
MAN'L/AUTO FM
DOWN UP
SPEAKERSPHONES
A
ON
OFF
B
ON
OFF
VOLUME
NATURAL SOUND STEREO RECEIVER
BASS
55
4
3
2
l
0
l
2
3
4
TREBLE
55
4
3
2
l
0
l
2
3
4
BALANCE
55
4
3
2
l
0
l
2
3
4
LR
LOUDNESS
57
6
4
3
2
l
FLAT
I0
9
8
l6
l8
20
24
28
34
40
50
60
70
l4
l2
l0
8
6
4
3
2
l
0
–dB
COPY
PRESET STATIONS
PRESET
MHz
MEMORY
AM
FM
TAPE MONITOR 12
STEREO
0
20
l00
ENTER
SLEEP
AUTO TUNING
-
30dB
RX-395
21A/B/C/D/E 3 4
6578
TAPE
MONITOR
AUX PHONO
TUNER CD
POWER
TUNING MODE
AUTO/MAN'L MONO
FM/AM TUNING EDIT MEMORY
MAN'L/AUTO FM
DOWN UP
SPEAKERSPHONES
A
ON
OFF
B
ON
OFF
VOLUME
NATURAL SOUND STEREO RECEIVER
BASS
55
4
3
2
l
0
l
2
3
4
TREBLE
55
4
3
2
l
0
l
2
3
4
BALANCE
55
4
3
2
l
0
l
2
3
4
LR
LOUDNESS
57
6
4
3
2
l
FLAT
I0
9
8
l6
l8
20
24
28
34
40
50
60
70
l4
l2
l0
8
6
4
3
2
l
0
–dB
PRESET STATIONS
PRESET
MHz
MEMORY
AM
FM
TAPE MONITOR 12
STEREO
0
20
l00
ENTER
SLEEP
AUTO TUNING
-
30dB
132456789
0A B C DEFG H
13245678
0A B C DEFG H
CONTROLS AND THEIR FUNCTIONS
7
English
1 POWER switch
Press this switch to switch the power on. Press it again to
switch the power off.
* Standby mode
<Australia and Singapore models only>
While the power is on, pressing the POWER key on the
remote control transmitter switches the unit to the standby
mode. (In this mode, the power indicator is half illuminated.)
2 Remote control sensor
Receives signals from the remote control transmitter.
3 Display panel
Shows station frequencies and various information. (Refer to
the next page for details.)
4 FM/AM buttons
Press this button to switch the reception band to FM or AM.
5 TUNING DOWN/UP button
Used for tuning. Press the “UP” side to tune in to higher
frequencies, and press the “DOWN” side to tune in to lower
frequencies.
6 EDIT button
This button is used to exchange the places of two preset
stations with each other.
7 MEMORY (MAN’L/AUTO FM) button
When this button is pressed, the MEMORY indicator flashes for
about 5 seconds. During this period, press the desired
PRESET STATIONS button to enter the displayed station into
the memory.
When this button is pressed and holded for about 3 seconds,
the automatic preset tuning begins.
8 Input selector buttons
Select a program source to listen to. When a button is
pressed, the name of selected source lights up on the display.
9 PURE DIRECT switch RX-495 only
Press this switch to listen to a source in the purest sound.
(Refer to page 16 for details.)
0 PHONES jack
When you listen with headphones, connect the headphones to
the PHONES jack. When listening with headphones privately,
set both the SPEAKERS A and B switches to the OFF
position.
A SPEAKERS switches
Set the switch A or B (or both A and B) for the speaker system
(connected to this unit) you will use to the ON position. Set the
switch for the speaker system you will not use to the OFF
position.
B TUNING MODE (AUTO/MAN’L) button
Press this button to switch the tuning mode to automatic or
manual. To select the automatic tuning mode, press this
button so that “AUTO TUNING” lights up on the display. To
select the
manual tuning mode, press this button so that “AUTO
TUNING” goes off.
C Tone controls
BASS
Used to increase or decrease the low frequency response.
The 0 position produces flat response.
TREBLE
Used to increase or decrease the high frequency response.
The 0 position produces flat response.
D BALANCE control
Adjusts the balance of the output volume to the left and right
speakers to compensate for sound imbalance caused by
speaker location or listening room conditions.
E A/B/C/D/E button
Press this button to select a desired group (A–E) of preset
stations.
F PRESET STATIONS buttons
Used to enter as many as 40 station frequencies into the
memory.
G Continuously variable LOUDNESS control
Used to compensate for the human ears’ loss of sensitivity to
high and low-frequency ranges at low volume.
H VOLUME control
Used to raise or lower the volume level.
PHONES
8
DISPLAY PANEL
AUTO TUNING
PRESET
STEREO
0
MHz
40 60
20
l00
MEMORY
SLEEP
TAPE MONITOR
FM
TAPE MONITOR TAPE MONITOR 12
1 Multi-information display
Displays various information, for example station frequency,
preset station number and name of selected program source.
2 STEREO indicator
Lights up when an FM stereo broadcast with sufficient signal
strength is received.
3 Signal-level meter
Indicates the signal level of the received station.
If multipath interfernce is detected, the indication decreases.
4 MEMORY indicator
When the MEMORY button is pressed, this indicator flashes for
about 5 seconds. During this period, the displayed station can
be programmed to the memory by using the A/B/C/D/E button
and one of the PRESET STATIONS buttons.
5 TAPE MONITOR indicator
RX-395
Lights up when the tape deck is selected as the input source
by pressing the TAPE MONITOR button.
RX-495
When the first tape deck is selected as the input source by
pressing the TAPE 1 button, “TAPE MONITOR 1” lights up,
and when the second tape deck is selected by pressing the
TAPE 2 button, “TAPE MONITOR 2” lights up.
6 AUTO TUNING indicator
This indicator lights up when this unit is in the automatic tuning
mode.
7 SLEEP indicator
Lights up while the built-in SLEEP timer is functioning.
RX-395 RX-495
132
5
467
9
English
REMOTE CONTROL TRANSMITTER
The remote control transmitter provided with this unit is designed to control all the most commonly used functions of the unit. If the
CD player and tape deck connected to this unit are YAMAHA components designed for remote control compatibility, then this
remote control transmitter will also control various functions of each component.
For Control of This Unit
1
Tuner keys
Controls tuner.
+: Selects higher preset station number.
–: Selects lower preset station number.
A/B/C/D/E Selects the group (A – E) of preset station
numbers.
2 SLEEP timer key
The power to this unit is automatically turned off one hour after
this key is pressed (so that “SLEEP” lights up on the display).
3 POWER key
Turns the power on/off.
*
<Australia and Singapore models only>
While the power is on, pressing the POWER key on the
remote control transmitter switches the unit from the
power-on mode to the standby mode, and vice versa. (In
the standby mode, the power indicator on the front panel is
half illuminated.)
4 VOLUME +/– keys
Turns the volume level up/down.
5 Input selector keys
Selects input source.
For Other Component Control
Identify the remote control transmitter keys with your
component’s keys. If these keys are identical, their functions
will be the same. On each key function, refer to the
corresponding instruction on your component’s manual.
1 Tape deck keys
Controls tape deck.
*
DIR A, B and A/B are applicable only to double
cassette tape deck.
*
For a single cassette deck with automatic reverse
function, pressing DIR A will reverse the direction of
tape running.
2 CD player keys
Controls compact disc player.
*
DISC is applicable only to compact disc changer.
YAMAHA HIFI SYSTEM
REMOTE CONTROL TRANSMITTER
REC/PAUSE
DIR BDIR A
DISC
SLEEP
A/B/C/D/E
PRESET
–+
A/B
TUNER
CD
PHONO
AUX
PLAY
PLAY
VOLUMEPOWER
1
2
2
3
5
4
TAPE 2
TAPE 1
1
TAPE
RX-395 RX-495
5
10
CONNECTIONS
Before attempting to make any connections to or from this unit, be sure to first switch OFF the power to this unit and to any other
components to which connections are being made.
CONNECTIONS WITH OTHER COMPONENTS
When making connections between this unit and other components, be sure all connections are made correctly, that is to say L (left)
to L, R (right) to R, “+” to “+” and “–” to “–”. Also, refer to the owner’s manual for each component to be connected to this unit.
*
If you have YAMAHA components numbered as 1, 2, 3, etc. on the rear panel, connections can be made easily by making
sure to connect the output (or input) terminals of each component to the same-numbered terminals of this unit.
:Refer to “ABOUT THE ACCESSORY TERMINALS” on page 12.
FM
GND
ANT
AM
ANT
GND
75Ω
UNBAL.
PHONO CD AUX TAPE 1 TAPE 2
or or
TAPE
PB
REC
OUT
TAPE
PB
REC
OUT
A OR B: 6
Ω
MIN./SPEAKER
A B : l2
Ω
MIN./SPEAKER
SPEAKERS
A
B
I20V 60Hz
I00W MAX. TOTAL
AC OUTLETS
SWITCHED
3
1
5 4 6 3 4
OUTPUT
LINE OUT
LINE IN
LINE OUT
LINE IN
AUDIO OUT
OUTPUT
GND
(U.S.A. model)
RX-495
Compact disc player
Video cassette player,
LD player, etc.
Speakers B
Right Left
Right Left
Turntable Tape deck 2Tape deck 1
Speakers A
To AC outlet
11
English
RX-395
FM
GND
ANT
AM
ANT
GND
75Ω
UNBAL.
PHONO CD AUX TAPE
or or
TAPE
PB
REC
OUT
A OR B : 6
Ω
MIN./SPEAKER
A B : l2
Ω
MIN./SPEAKER
SPEAKERS
A
B
I20V 60Hz
I00W MAX. TOTAL
AC OUTLETS
SWITCHED
3
1
5 4 6
OUTPUT
LINE OUT
LINE IN
AUDIO OUT
OUTPUT
GND
:Refer to “ABOUT THE ACCESSORY TERMINALS” on page 12.
(U.S.A. model)
Compact disc player
Video cassette player,
LD player, etc.
Speakers B
Right Left
Right Left
Turntable Tape deck
Speakers A
To AC outlet
12
CONNECTING SPEAKERS
Connect the SPEAKERS terminals to your speakers with wire
of the proper gauge, cut as short as possible. If the
connections are faulty, no sound will be heard from the
speakers. Make sure that the polarity of the speaker wires is
correct, that is, + and – markings are observed. If these wires
are reversed, the sound will be unnatural and will lack bass.
Do not let the bare speaker wires touch each other and do
not let them touch the metal parts of this unit as this could
damage this unit and/or speakers.
How to Connect:
Red: positive (+)
Black: negative (–)
➀
Unscrew the knob.
➁
Insert the bare wire.
[Remove approx. 5mm
(1/4”) insulation from
the speaker wires.]
➂
Tighten the knob and
secure the wire.
Notes
●
One or two speaker systems can be connected to this unit.
If you connect only one speaker system, connect it to either
the SPEAKERS A or B terminals.
●
Use speakers with the specified impedance shown on the
rear of this unit.
●
<U.S.A., Canada, Australia and General models only>
Banana Plug connections are also possible. Simply insert
the Banana Plug connector into the corresponding terminal.
1
2
3
ABOUT THE ACCESSORY TERMINALS
AC OUTLETS (SWITCHED)
(U.S.A., Canada, Singapore and General models)
.......................................................... 2 SWITCHED OUTLETS
(Australia model) ................................. 1 SWITCHED OUTLET
Use these to connect the power cords from your components
to this unit.
The power to the SWITCHED outlets is controlled by this unit’s
POWER switch or the provided remote control transmitter’s
POWER key. These outlets will supply power to any
component whenever this unit is turned on.
The maximum power (total power consumption of
components) that can be connected to the SWITCHED AC
OUTLETS is 100 watts.
GND terminal (For turntable use)
Connecting the ground wire of the turntable to the GND
terminal will normally minimize hum, but in some cases better
results may be obtained with the ground wire disconnected.
Use one of the two GND terminals on the rear of this unit for
the connection.
FM
ANT
AM
ANT
GND
75Ω
UNBAL
GND
or
Turntable
Loosen Tighten
13
English
ANTENNA CONNECTIONS
●
Each antenna should be connected to the designated terminals correctly, referring to the following diagram.
●
Both AM and FM indoor antennas are included with this unit. In general, these antennas will probably provide sufficient signal
strength. Nevertheless, a properly installed outdoor antenna will give clearer reception than an indoor one. If you experience
poor reception quality, an outdoor antenna may result in improvement.
Connecting the AM loop antenna
* The AM loop antenna should be placed apart from the main unit. The antenna may be hung on a wall.
* The AM loop antenna should be kept connected, even if an outdoor AM antenna is connected to this unit.
GND terminal
For maximum safety and minimum interference, connect the
GND terminal to a good earth ground. A good earth ground is
a metal stake driven into moist earth.
Notes
●
When connecting the indoor
FM antenna, insert its
connector into the FM ANT
terminal firmly.
●
If you need an outdoor
FM antenna to improve
FM reception quality, either
300-ohm feeder or coaxial cable may be used. In locations
troubled by electrical interference, coaxial cable is
preferable.
FM
GND
ANT
AM
ANT
GND
75Ω
UNBAL.
PHONO CD AUX
1
Outdoor FM antenna
Indoor FM
antenna
(included)
75-ohm/300-ohm
antenna adapter
75-ohm
coaxial cable
300-ohm
feeder
Outdoor AM antenna
AM loop
antenna
(included)
Ground
➀
➁
➂
Orient so that the best
reception is obtained.
12 3
14
1
Set to the “
∞
” position.
2 Turn the power on.
3 Select the desired input source by using the input
selector buttons.
* The name of the selected input source will appear on the
display.
* Note that pressing on each input selector button selects the
source which is connected to the corresponding input
terminals on the rear panel.
4 Select the speakers to be used.
* If you use two speaker systems, press both the A and
B switches.
5 Play the source. (For detailed information on the
tuning operation, refer to page 17.)
6
Adjust to the desired output level.
7 If desired, adjust the BASS, TREBLE, BALANCE and
LOUDNESS controls, etc. (refer to page 16).
Notes
RX-495 only
●
If you select AUX, TUNER, CD or PHONO, be sure that
TAPE 1 and/or TAPE 2 are not being selected.
●
If you select TAPE 1 and TAPE 2 at the same time, the
result will be the sound from the tape deck 1.
●
For TAPE 1 and TAPE 2, whenever the button is pressed,
the corresponding input source is selected or canceled
alternately.
RX-395 only
●
Whenever the TAPE MONITOR is pressed, the tape deck
is selected or canceled alternately.
●
If both TAPE MONITOR and another input selector button
are selected, TAPE MONITOR takes priority of another
input selector button.
To turn off the power
Press the POWER switch again.
BASIC OPERATIONS
TO PLAY A SOURCE
SPEAKERS
A
ON
OFF
B
ON
OFF
TAPE 1TAPE 2
MONITOR
AUX PHONO
TUNER CD
COPY
TAPE
MONITOR
AUX PHONO
TUNER CD
3
1, 6
2
4
7
POWER
RX-495
RX-395
15
English
RX-395
1
Select the source to be recorded.
* To dub from tape to tape, refer to the “Notes” shown
below.
* When you select AUX, TUNER, CD or PHONO, make
sure that neither TAPE 1 nor TAPE 2 is also selected.
2
Play the source and then turn the VOLUME control up
to confirm the input source. (For detailed information
on the tuning operations, refer to the page 17.)
3
Begin recording on the tape deck.
4
To monitor the audio signals being recorded, press the
input selector button for the tape deck being used to
make the recording.
TAPE 1TAPE 2
MONITOR
AUX PHONO
TUNER CD
COPY
TAPE 1TAPE 2
MONITOR
AUX PHONO
TUNER CD
COPY
1, 4
2
1
Select the source to be recorded.
* When you select AUX, TUNER, CD or PHONO, make
sure that TAPE MONITOR is not also selected.
2
Play the source and then turn the VOLUME control up
to confirm the input source. (For detailed information
on the tuning operations, refer to the page 17.)
3
Begin recording on the tape deck.
4
To monitor the audio signals being recorded, press the
TAPE MONITOR.
Note
VOLUME, BASS, TREBLE, BALANCE and LOUDNESS
control settings have no effect on the material being recorded.
TAPE
MONITOR
AUX PHONO
TUNER CD
TAPE
MONITOR
AUX PHONO
TUNER CD
RX-495
TO RECORD A SOURCE TO TAPE
Notes
●
VOLUME, BASS, TREBLE, BALANCE, LOUDNESS
controls and PURE DIRECT switch settings have no effect
on the material being recorded.
●
To dub from tape to tape, select TAPE 2 by pressing it.
Only the following method of dubbing can be made by using
this unit.
SOURCE
Tape deck connected to
the TAPE 2 terminals.
RECORDER
Tape deck connected to
the TAPE 1 terminals.
→
16
Because one or two speaker systems can be connected to this
unit, the SPEAKERS switches allow you to select speaker
system A or B, or both at once.
Adjust the balance of the output volume to the left and right
speakers to compensate for sound imbalance caused by
speaker location or listening room conditions.
BASS : Turn this clockwise to increase (or counter-
clockwise to decrease) the low frequency
response.
TREBLE : Turn this clockwise to increase (or counter-
clockwise to decrease) the high frequency
response.
Selecting the SPEAKER system
Adjusting the BASS and TREBLE
controls
Adjusting the BALANCE control
SPEAKERS
A
ON
OFF
B
ON
OFF
BALANCE
55
4
3
2
l
0
l
2
3
4
LR
TREBLE
55
4
3
2
l
0
l
2
3
4
BASS
55
4
3
2
l
0
l
2
3
4
Adjusting the continuously variable
LOUDNESS control
This control provides compensation for the human ears’ loss of
sensitivity to high and low-frequency ranges at low volume.
This control is adjustable to retain full tonal range at any
volume level.
1
Set to the “FLAT” position.
2
Set to the loudest listening
level that you would listen
to.
3
Turn until the desired
volume is gained.
LOUDNESS
57
4
3
2
l
FLAT
l0
9
8
6
30 dB
LOUDNESS
57
4
3
2
l
FLAT
l0
9
8
6
30 dB
VOLUME
l6
l8
20
24
28
34
40
50
60
70
l4
l2
l0
8
6
4
3
2
l
0
–dB
Using the PURE DIRECT switch
RX-495 only
You can enjoy the purest possible sound from your audio
sources by pressing this switch inward. By doing so, the audio
signal bypasses the BASS, TREBLE, BALANCE and
LOUDNESS controls, eliminating any alterations to the audio
signal.
PURE DIRECT
17
English
Note
If you tune to an FM station manually, it is received in
monaural mode automatically to increase the signal quality.
1 Select the reception band (FM or AM) confirming it on
the display.
2
3 Tune to a desired station manually.
* To continue tuning search, press and hold the button.
FM/AM
FM AM
or
1 Select the reception band (FM or AM) confirming it on
the display.
2
3
To tune to a higher frequency, press the right side once.
To tune to a lower frequency, press the left side once.
* If the station where tuning search stops is not the desired
one, press again.
* If the tuning search does not stop at the desired station
(because the signals of the station are weak), change to
the MANUAL TUNING method.
TUNING OPERATIONS
Normally, if station signals are strong and there is no interference, quick automatic-search tuning (AUTOMATIC TUNING) is
possible. However, if signals of the station you want to select are weak, you must tune to it manually (MANUAL TUNING).
AUTOMATIC TUNING MANUAL TUNING
FM/AM
TUNING MODE
AUTO/MAN'L MONO
TUNING MODE
AUTO/MAN'L MONO
TUNING
DOWN UP
TUNING
DOWN UP
AUTO TUNING
Turn “AUTO TUNING”
off.
FM AM
or
1 3
2
18
1 Tune to a desired station.
(Refer to the previous page for tuning procedure.)
2 Select a desired group (A – E) of preset stations
confirming it on the display.
3
4 Select a preset station number where you want to
program the station before “MEMORY” goes off from the
display.
* In the same way, program other stations to A2, A3 ... A8.
* You can program more stations to preset station numbers
on other groups in the same way by selecting other
groups in step 2.
11 Select the group of preset stations.
22 Select the preset station number.
Notes
●
A new setting can be programmed in place of the former
one.
●
For presets, the setting of the reception mode (stereo or
monaural) is stored along with the station frequency.
Memory back-up
The memory back-up circuit prevents the programmed data
from being lost even if the POWER switch is set off or the
power plug is disconnected from the AC outlet or the power is
cut due to temporary power failure. If, however, the power is
cut for more than one week, the memory may be erased. If
so, it can be re-programmed by simply following the PRESET
TUNING steps.
MANUAL PRESET TUNING
This unit can store station frequencies (selected by tuning operation) by using the PRESET STATIONS buttons. With this function,
you can recall any desired station by only pressing the corresponding PRESET STATIONS button. Up to 40 stations (8 stations x 5
groups) can be stored.
PRESET TUNING
To store stations
3
2, 11
4, 22
A/B/C/D/E
PRESET
2134
6578
PRESET STATIONS
PRESET
MHz
FM
0
20
l00
40 60
Shows the displayed station has been programmed to A1.
MEMORY
MAN'L/AUTO FM
MEMORY
Flashes on and off for
about 5 seconds.
To recall a preset station
PRESET
A/B/C/D/E
2134
6578
PRESET STATIONS
PRESET
19
English
To store stations
1 2
AUTOMATIC PRESET TUNING
You can also make use of an automatic preset tuning function for FM stations only. By this function, this unit performs automatic
tuning and stores FM stations with strong signals sequentially. Up to 40 stations are stored automatically in the same way as in the
manual preset tuning method on page 18.
1
2
After 5 seconds, the automatic preset tuning begins from A1.
Received stations are programmed to A1, A2 ... A8
sequentially.
* If more than 8 stations are received, they are also
programmed to the preset station numbers on other groups
(B, C, D and E) in that order.
If you want to store the first station received by the
automatic preset tuning to a desired preset station
number.
If, for example, you want to store the first received station to
C5, select “C5” by using the A/B/C/D/E button and the
PRESET STATIONS buttons after pressing the MEMORY
button in step 2 before the automatic preset tuning begins. The
first received station is stored to C5, and next stations to C6,
C7 ... sequentially.
If stations are stored up to E8, the automatic preset tuning is
finished automatically.
When the automatic preset tuning is finished
The display shows the frequency of the last preset station.
Check the contents and the number of preset stations by
following the procedure of the section “To recall a preset
station” on page 18.
To recall a preset station
Simply follow the procedure of the section “To recall a preset
station” on page 18.
Notes
●
If no station is received by the automatic preset tuning
search, the search finishes after
“NOTHING” flashes for
about 3 seconds on the display.
●
You can replace a preset station by another FM or AM
station manually by simply following the procedure of the
section “To store stations” on page 18.
●
If the number of received stations is not enough to be stored
up to E8, the search will be finished automatically when it
reaches the highest frequency after searching through all
frequencies.
●
With this function, only FM stations with sufficient signal
strength are stored automatically. If the station you want to
program is weak in signal strength, tune to it in monaural
manually and program it by following the procedure of the
section “To store stations” on page 18.
Press and hold for
about 3 seconds.
FM/AM
FM
MEMORY
MAN'L/AUTO FM
MEMORY
AUTO TUNING
Flashes.
20
EXCHANGING PRESET STATIONS
You can exchange the places of two preset stations with each other as shown below.
Example)
If you want to shift the preset station on E1 to A5, and vice
versa.
1 Recall the preset station on E1 (by following the method
of “To recall a preset station” on page 18).
2
3 Next, recall the preset station on A5 by following the
same method with step 1.
4
Flashes
EDIT
EDIT
Flashes
MEMORY
MEMORY
2, 4
Shows the exchange of
stations is completed.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
Yamaha RX-395 Manuel utilisateur
- Catégorie
- Tuners audio
- Taper
- Manuel utilisateur
- Ce manuel convient également à
dans d''autres langues
- italiano: Yamaha RX-395 Manuale utente
- English: Yamaha RX-395 User manual
- español: Yamaha RX-395 Manual de usuario
- Deutsch: Yamaha RX-395 Benutzerhandbuch
- русский: Yamaha RX-395 Руководство пользователя
- Nederlands: Yamaha RX-395 Handleiding
- português: Yamaha RX-395 Manual do usuário
- dansk: Yamaha RX-395 Brugermanual
- polski: Yamaha RX-395 Instrukcja obsługi
- čeština: Yamaha RX-395 Uživatelský manuál
- svenska: Yamaha RX-395 Användarmanual
- Türkçe: Yamaha RX-395 Kullanım kılavuzu
- suomi: Yamaha RX-395 Ohjekirja
- română: Yamaha RX-395 Manual de utilizare
Documents connexes
-
Yamaha RX-395RDS Le manuel du propriétaire
-
-
-
-
-
-
-
-
-
Yamaha T-S500 Le manuel du propriétaire
