Halsey Taylor HACBL.A Le manuel du propriétaire
- Taper
- Le manuel du propriétaire
Page 1
HAC8F(S)BL-Q*1A
97065C (Rev. D - 10/00)
USES HFC-134A REFRIGERANT
HALSEY TAYLOR OWNERS MANUAL
31,32,
33,34
30
29
17
19
16
38
18
43
8
1
28,39,
41
2,3,4,5
6,7
8
9,10
11,12
27
35,36
37
40
13
14
26
23
15
20,21,
22
24,25,
42, 65
19
See Fig. 3 (Page 3) For
Push Bar Mechanism
Page 2
HAC8F(S)BL-Q*1A
97065C (Rev. D - 10/00)
FIG. 2
*ADA REQUIREMENT
*REQUISITO DE A.D.A.
*EXIGENCE ADA
**When replacing a Model BFC with a new unit
Model HAC, installer must cut 1-1/2 inches from
length of cooler waste line before connecting to trap
(see installation instruction No.7)
**Cuando reemplace un Modelo BFC con una
unidad nueva Modelo HAC el instalador
deberá cortar 1½ pulgadas del largo del tubo
de desagüe del enfriador antes de conectar el
purgador (vea las instrucciones de instalación
No. 7)
**En remplaçant un modèle BFC avec un
nouveau modèle HAC, linstallateur doit
couper 1 1/2 pouce de longueur de la
canalisation résiduaire du refroidisseur avant
de le raccorder au siphon (voir instruction
dinstallation no. 7)
LEGEND/LEYENDA/LÉGENDE
A = RECOMMENDED WATER SUPPLY LOCATION 3/8 O.D. UNPLATED COPPER TUBE CONNECT STUB 1-1/2 IN. (38 mm) OUT FROM WALL SHUT
OFF BY OTHERS
SE RECOMIENDA UBICAR EL TUBO CORTO DE CONEXIÓN AL TUBO DE COBRE SIN CHAPAR DE 3/8" DE DIÁM. EXT. A 1-1/2" (38 mm) FUERA
DE LA LLAVE DE PASO EN LA PARED COLOCADA POR TERCEROS.
EMPLACEMENT RECOMMANDÉ D'ALIMENTATION EN EAU PAR TUBE EN CUIVRE NON PLAQUÉ DE 3/8 PO. (9,5 mm) D.E. CONNECTANT UNE
TUYAUTERIE DE 1-1/2 PO. (38 mm) DEPUIS LE ROBINET D'ARRÊT FOURNI PAR D'AUTRES.
B = RECOMMENDED LOCATION FOR WASTE OUTLET 1-1/4 O.D. DRAIN
UBICACIÓN RECOMENDADA PARA EL DRENAJE DE SALIDA DE AGUA, DE 1¼ DE DIÁMETRO.
EMPLACEMENT RECOMMANDÉ POUR LE DRAIN DE D.E. 1-1/4" DE SORTIE DEAU.
C = 1-1/4 TRAP NOT FURNISHED**
PURGADOR DE 1¼ NO PROPORCIONADO**
SIPHON 1-1/4 NON FOURNI**
D = ELECTRICAL SUPPLY (3) WIRE RECESSED BOX
CAJA RECESIVA DE ALAMBRES (3) DE SUMINISTRO ELÉCTRICO
BOÎTE ENCASTRÉE DALIMENTATION ÉLECTRIQUE (3) FILS
E = INSURE PROPER VENTILATION BY MAINTAINING 6" (152 mm) (MIN.) CLEARANCE FROM CABINET LOUVERS TO WALL.
ASEGURE UNA VENTILACIÓN ADECUADA MANTENIENDO UN ESPACIO E 6" (152 mm) (MÍN.) DE HOLGURA ENTRE LA REJILLA DE
VENTILACIÓN DEL MUEBLE Y LA PARED
ASSUREZ-VOUS UNE BONNE VENTILATION EN GARDANT 6" (152 mm) (MIN.) ENTRE LES ÉVENTS DE LENCEINTE ET LE MUR.
F = 7/16 BOLT HOLES FOR FASTENING UNIT TO WALL
AGUJEROS DE LAS TUERCAS DE 7/16 PARA SUJETAR LA UNIDAD A LA PARED
TROUS DÉCROUS 7/16 POUR FIXER LAPPAREIL AU MUR
Page 3
HAC8F(S)BL-Q*1A
97065C (Rev. D - 10/00)
COOLER BACK
SUPPORT DE SUSPENSION
ARRIÈRE DU REFROIDISSEUR
HANGER BRACKET
FIJADOR DE SUSPENSIÓN
SUPPORT DE SUSPENSION
PUSH BAR MECHANISM
IMPORTANT
ALL SERVICE TO BE PERFORMED BY AN
AUTHORIZED SERVICE PERSON
HANGER BRACKETS & TRAP
INSTALLATION
1) Remove hanger bracket fastened to back of cooler by
removing one (1) screw.
2) Mount the hanger bracket and trap as shown in Figure 2.
NOTE: Hanger Bracket MUST be supported securely. Add
fixture support carrier if wall will not provide adequate
support.
IMPORTANT:
7 in. (178mm) dimension from wall to centerline of trap must
be maintained for proper fit.
Anchor hanger securely to wall using all six (6) 1/4 in. dia.
mounting holes.
3) Install straight valve for 3/8" O.D. tube.
INSTALLATION OF COOLER
4) Hang the cooler on the hanger bracket. Be certain the
hanger bracket is engaged properly in the slots on the cooler
back as shown in Fig. 4.
5) Loosen the two (2) screws holding the lower front panel at
the bottom of cooler base and two (2) screws at the top.
Remove the front panel and set aside.
6) Connect water inlet line--See Note 4 of General Instructions.
7) Remove the slip nut and gasket from the trap and install
them on the cooler waste line making sure that the end of
the waste line fits into the trap. Assemble the slip nut and
gasket to the trap and tighten securely.
START UP
Also See General Instructions
8) Stream height is factory set at 45-50 PSI. If supply
pressure varies greatly from this, readjust stream height to
approximately 1-1/2" (38mm) above the bubbler guard by
turning adjustment screw, accessible by removing front push
panel,ItemNo.51 (see Fig.3 & 5).
9) Replace the front panel and secure by retightening four (4)
screws.
10) If a taste, odor or sediment problem is prevalent, try
installing our water filter module, part no 73-15242-51-550
FIG. 3
CORRECT STREAM HEIGHT
FIG. 4
FIG. 5
CAUTION: Cleaning of Aztec Gold Models requires special
care. Outer surfaces must be cleaned with a mild detergent or
mixture of vinegar and water only, rinsed and wiped dry.
Abrasive and acidic cleaners may eventually damage the Aztec
Gold finish.
LEGEND
A) Note: Water flow direction
B) Adjust this screw to eliminate mechanism Free Play or continuous flow
from bubbler conditions. (See ADJUSTMENT PROCEDURE)
C) Stream height adjustment (see note #8)
Water Valve Mechanism - ADJUSTMENT PROCEDURE:
- Turn adjustment screw (Item 62) Counter-Clockwise until water flow from bubbler
starts.
- Turn adjustment screw Clockwise until water flow stops, THEN turn an additional
1/2 turn.
NOTE: Adjustments stated above are viewed from underneath unit (bottom side of
dispenser panel Item 45)
NOTE: If continuous flow occurs at the end of the compressor cycle, turn cold control
(Item 38) counterclockwise 1/4 turn.
49
54
47
53
50
51
52
54
56
62
C
47
64
48
52
51
54
44
54
63
46
45
46
59
58
57
60
61
A
B
)
55
Page 4
HAC8F(S)BL-Q*1A
97065C (Rev. D - 10/00)
FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.323.0620
*REPLACE WITH SAME COMPRESSOR USED IN ORIGINAL ASSEMBLY.
NOTE: All correspondence pertaining to any of the above water coolers or
orders for repair parts MUST include Model No. and Serial No. of cooler, name and
part number of replacement part.
PRINTED IN U.S.A.
2222 CAMDEN COURT
OAK BROOK, IL 60523
630.574.3500
ITEMIZED PARTS LIST
ITEM
NO
DESCRIPTION
1
2, 2a
2b
3
4, 4a
4b
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23*
23a*
23b*
23c*
24
24a
24b
24b
24c
25, 25a
25b
25b
25b
25c
26, 26b
26a
26c
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65c
NS
31517C
30699C
30664C
70018C
31490C
31491C
70009C
22899C
38417001
70241C
62296C
10079C
51544C
45396C
10-03227-40-560
62152C
66202C
See Color Table
See Color Table
See Color Table
See Color Table
See Color Table
10-15161-43-550
10-08067-40-570
19037000
35767C
35761C
35807C
35947C
31025C
31026C
35801C
35795C
31039C
35766C
30181C
30180C
30182C
35768C
66214C
66215C
66386C
62198C
70836C
40022C
16-07448-51-550
40590C
10-01471-40-560
10-26399-31-640
45413C
16-02705-08-640
45400C
22893C
27594C
11-26275-43-890
75573C
10-06876-08-640
75571C
31513C
62220C
70002C
70767C
19-42439-01-550
55996C
See Color Table
22897C
51531C
11-14117-43-620
See Color Table
See Color Table
See Color Table
55859C
55947C
55948C
22900C
70864C
50212C
51667C
40045C
23003C
15005C
61314C
50986C
70935C
11-26275-43-890
22901C
35935C
40-06609-43-730
PART NO
Power Cord
Fan Blade
Fan Blade
Hex Nut - Fan Blade
Fan Motor
Fan Motor
Screw - (Fan Motor)
Shroud - Fan
Screw - #8-18 x 3/8" Lg. (Fan Shroud)
Clip (Front and Rear Panels)
Tube Assembly - Bubbler
Nipple - Bubbler (included with Item No. 9)
Bubbler - Chrome
Bubbler - Aztec Gold
Gasket - Bubbler (upper and lower)
Condenser
Drier
Panel - Right Rear (Refrig. Unit)
Panel - Right Rear (Left Unit)
Panel - Left Rear (Left Unit)
Panel - Left Rear (Refrig. Unit)
Panel - Front Lower
Stud - Compressor Mtg.
Grommet - Compressor Mtg.
Clip - Compressor Mtg.
Compressor Serv. Pak FF7.5HBK
Compressor Serv. Pak FF6HBK
Compressor Serv. Pak AE3425Y
Compressor Serv. Pak EM65
Overload /Relay 1.350.358
Overload /Relay 1.350.356
Relay 9660-042-166
Overload MRP26ALL-69
Overload/Relay P600B/427NFBYY
Cover - Relay
Cover - Terminal
Overload Spring
Bale Strap
Cover - Relay
Heat Exchanger
Heat Exchanger
Heat Exchanger
Tube - Cu. 1/4 x 36"
Elbow
Waste Line Assembly
Tailpiece Assembly (Left Unit)
Waste Line Assembly
Gasket - Drain
Drain Plug - Chrome
Drain Plug - Aztec Gold
Strainer Plate - Chrome
Strainer Plate - Aztec Gold
Basin - Stainless Steel
Basin - Aztec Gold
Screw - Basin Mtg. Stainless Steel
Screw - Basin Mtg. Aztec Gold
Plug Button - Chrome
Plug Button - Aztec Gold
Cold Control
Evaporator Assembly
Screw - #10 x 1/2" Lg. HHSM
Clip - Evaporator Retaining
Cover - Electrical Shield
Strainer
Cover - Dispenser Bottom
Panel - Bottom Dispenser
Block - Pivot
Nut - 1/4 , Self-Threading
Panel - Right Side
Panel - Left Side
Panel - Front Push
Pushbar - Side & Front
Insert - Push Bar, Gray
Insert - Push Bar, Brown
Bracket - Front Push
Screw - #8 x 5/8" Lg. Torx/Slot
Rivet - Drive Type
Bumper - Press Bar
Hex Nut
Bracket - Regulator Mounting
Retaining Nut
Regulator
Holder - Regulator
Screw - Shoulder x 1/2" Lg.
Screw - Regulator Brkt. Mtg.
Bracket - Side Push
Capacitor - Run
Hanger Bracket
Item No. 15
Part No.
COLOR TABLE
Almond Vinyl
Aztec Gold
Platinum Vinyl
Stainless Steel
Slate Vinyl
22968C
27491C
22860C
22862C
22864C
26772C
27511C
26806C
26776C
26810C
22961C
27487C
22852C
22854C
22856C
PANEL
COLOR
26765C
27507C
26798C
26800C
26802C
22954C
27499C
22844C
22955C
22848C
Item No. 16
Part No.
Item No. 18
Part No.
Item No. 19
Part No.
Item No. 17
Part No.
Item No. 48
Part No.
(w/o hole)
COLOR TABLE - PUSH BAR MECHANISM
Almond Vinyl
Aztec Gold
Platinum Vinyl
Stainless Steel
Slate Vinyl
23016C
27503C
22820C
22822C
22824C
22947C
27483C
22836C
22838C
22840C
23009C
27433C
22812C
22814C
22816C
PANEL
COLOR
22940C
27479C
22828C
22830C
22832C
26848C
27596C
22804C
22806C
22808C
Item No. 48
Part No.
(with hole)
Item No. 49
Part No.
(with hole)
Item No. 50
Part No.
Item No. 49
Part No.
(w/o hole)
Item No. 44
Part No.
55931C
55930C
55931C
55931C
55931C
-
1
-
2
-
3
-
4
Halsey Taylor HACBL.A Le manuel du propriétaire
- Taper
- Le manuel du propriétaire
Documents connexes
-
Halsey Taylor HACBL.B Le manuel du propriétaire
-
-
-
-
-
-
-
-
-