ICE MAKER
Use & Care Guide
For questions about features, operation/performance,
parts, accessories or service, call: 1-800-253-1301.
In Canada, for assistance, installation
or service call: 1-800-807-6777
or visit our website at...
www.whirlpool.com or www.whirlpoolappliances.ca
MACHINE À GLAÇONS
Guide d’utilisation
et d’entretien
Au Canada, pour assistance, installation
ou service, appeler le : 1-800-807-6777
ou visitez notre site web à
www.whirlpoolappliances.ca
Table of Contents/Table des matières................2
W10206421B
®
2
TABLE OF CONTENTS
ICE MAKER SAFETY......................................................................3
INSTALLATION INSTRUCTIONS..................................................4
Unpack the Ice Maker..................................................................4
Location Requirements................................................................4
Electrical Requirements ...............................................................5
Water Supply Requirements........................................................5
Leveling ........................................................................................5
Connect Water Supply.................................................................6
Drain Connection .........................................................................7
Ice Maker Door.............................................................................8
Normal Sounds ..........................................................................10
ICE MAKER USE ..........................................................................10
How Your Ice Maker Works .......................................................10
Using the Controls .....................................................................11
ICE MAKER CARE........................................................................11
Cleaning......................................................................................11
Vacation and Moving Care.........................................................13
TROUBLESHOOTING ..................................................................14
Ice Maker Operation...................................................................14
Ice Production ............................................................................14
Ice Quality...................................................................................15
Plumbing Problems....................................................................15
ASSISTANCE OR SERVICE.........................................................15
In the U.S.A. ...............................................................................15
In Canada ...................................................................................15
WARRANTY ..................................................................................16
TABLE DES MATIÈRES
SÉCURITÉ DE LA MACHINE À GLAÇONS................................17
INSTRUCTIONS D’INSTALLATION ............................................18
Déballage de la machine à glaçons...........................................18
Exigences d'emplacement.........................................................18
Spécifications électriques..........................................................19
Spécifications de l’alimentation en eau.....................................19
Nivellement.................................................................................19
Raccordement à la canalisation d’eau ......................................20
Raccordement au drain de vidange...........................................21
Porte de la machine à glaçons ..................................................22
Sons normaux ............................................................................24
UTILISATION DE LA MACHINE À GLAÇONS............................24
Fonctionnement de la machine à glaçons.................................24
Utilisation des commandes........................................................25
ENTRETIEN DE LA MACHINE À GLAÇONS..............................25
Nettoyage ...................................................................................25
Précautions à prendre avant les vacances
ou un déménagement ................................................................28
DÉPANNAGE.................................................................................29
Fonctionnement de la machine à glaçons.................................29
Production de glaçons ...............................................................29
Qualité des glaçons....................................................................30
Problèmes de plomberie............................................................30
ASSISTANCE OU SERVICE.........................................................30
GARANTIE.....................................................................................31
3
ICE MAKER SAFETY
You can be killed or seriously injured if you don't immediately
You
can be killed or seriously injured if you don't
follow
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
follow instructions.
instructions.
DANGER
WARNING
IMPORTANT SAFETY INSTRUCTIONS
WARNING : To reduce the risk of fire, electric shock, or injury when using your ice maker, follow these basic
precautions
:
SAVE THESE INSTRUCTIONS
■ Plug into a grounded 3 prong outlet.
■ Do not remove ground prong.
■ Do not use an adapter.
■ Do not use an extension cord.
■ Disconnect power before cleaning.
■ Disconnect power before servicing.
■ Replace all parts and panels before operating.
■ Use two or more people to move and install ice maker.
4
INSTALLATION INSTRUCTIONS
Unpack the Ice Maker
Removing Packaging Materials
Remove tape and glue from your ice maker before using.
■ To remove any remaining tape or glue from the exterior of the
ice maker, rub the area briskly with your thumb. Tape or glue
residue can also be easily removed by rubbing a small
amount of liquid dish soap over the adhesive with your
fingers. Wipe with warm water and dry.
■ Do not use sharp instruments, rubbing alcohol, flammable
fluids, or abrasive cleaners to remove tape or glue. Do not
use chlorine bleach on the stainless steel surfaces of the ice
maker. These products can damage the surface of your ice
maker.
Cleaning Before Use
After you remove all of the packaging materials, clean the inside
of your ice maker before using it. See the cleaning instructions in
the “Ice Maker Care” section.
Location Requirements
■ To ensure proper ventilation for your ice maker, the front side
must be completely unobstructed. The ice maker may be
closed-in on the top and three sides, but the installation
should allow the ice maker to be pulled forward for servicing
if necessary.
■ Installation of the ice maker requires a cold water supply inlet
of ¹⁄₄" (6.35 mm) OD soft copper tubing with a shutoff valve
and either a gravity-drain system or condensate pump to
carry the water to an existing drain.
■ Choose a well ventilated area with temperatures above 55°F
(13°C) and below 110°F (43°C). Best results are obtained
between 70°F (21°C) and 90°F (32°C).
■ The ice maker must be installed in an area sheltered from the
elements, such as wind, rain, water spray, or drip.
■ When installing the ice maker under a counter, follow the
recommended opening dimensions shown. Place electrical
and plumbing fixtures in the recommended location as
shown.
NOTES:
■ Be sure the power supply cord is not pinched between
the ice maker and the cabinet.
■ Be sure the water supply line is not pinched between the
ice maker and the cabinet.
■ Be sure the drain line (on some models) is not pinched
between the ice maker and the cabinet.
■ Choose a location where the floor is even. It is important for
the ice maker to be level in order to work properly. If needed,
you can adjust the height of the ice maker by changing the
height of the leveling legs. See “Leveling.”
WARNING
Excessive Weight Hazard
Use two or more people to move and install ice maker.
Failure to do so can result in back or other injury.
A. Recommended location for electrical
and plumbing fixtures
B. Floor level
11¹⁄₂"
(29.2 cm)
15"
(38.1 cm)
24"
(60.1 cm)
9"
(22.9 cm)
28¹⁄₂"
(72.4 cm)
34"
(86.4 cm)
Min.
34
¹⁄₂"
(87.6 cm)
Max.
3¹⁄₂"
(8.9 cm)
B
A
5
Electrical Requirements
Before you move your ice maker into its final location, it is
important to make sure you have the proper electrical
connection:
A 115 Volt, 60 Hz., AC only, 15- or 20-amp electrical supply,
properly grounded in accordance with the National Electrical
Code and local codes and ordinances, is required.
It is recommended that a separate circuit, serving only your ice
maker, be provided. Use a receptacle which cannot be turned off
by a switch or pull chain.
IMPORTANT: If this product is connected to a GFCI (Ground
Fault Circuit Interrupter) equipped outlet, nuisance tripping of the
power supply may occur, resulting in loss of cooling. Ice quality
may be affected. If nuisance tripping has occurred, and if the
condition of the ice appears poor, dispose of it.
Recommended grounding method
The ice maker must be grounded. The ice maker is equipped with
a power supply cord having a 3 prong grounding plug. The cord
must be plugged into a mating, 3 prong, grounding-type wall
receptacle, grounded in accordance with the National Electrical
Code and local codes and ordinances. If a mating wall receptacle
is not available, it is the personal responsibility of the customer to
have a properly grounded, 3 prong wall receptacle installed by a
qualified electrician.
Water Supply Requirements
A cold water supply with water pressure of between 30 and
120 psi (207 and 827 kPa) is required to operate the ice maker. If
you have questions about your water pressure, call a licensed,
qualified plumber.
Reverse Osmosis Water Supply
IMPORTANT:
■ Reverse osmosis water filtration systems can be used only
with ice maker installations that have a gravity drain. A
reverse osmosis system is not recommended for ice makers
that have a drain pump installed.
■ The pressure of the water supply coming out of a reverse
osmosis system going to the water inlet valve of the ice
maker needs to be between 30 and 120 psi (207 and
827 kPa).
If a reverse osmosis water filtration system is connected to your
cold water supply, the water pressure to the reverse osmosis
system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).
NOTE: The reverse osmosis system must provide 1 gal. (3.8 L) of
water per hour to the ice maker for proper ice maker operation. If
a reverse osmosis system is desired, only a whole-house
capacity reverse osmosis system, capable of maintaining the
steady water supply required by the ice maker, is recommended.
Faucet capacity reverse osmosis systems are not able to
maintain the steady water supply required by the ice maker.
If the water pressure to the reverse osmosis system is less than
40 to 60 psi (276 to 414 kPa):
■ Check to see whether the sediment filter in the reverse
osmosis system is blocked. Replace the filter if necessary.
■ Allow the storage tank on the reverse osmosis system to refill
after heavy usage.
If you have questions about your water pressure, call a licensed,
qualified plumber.
Leveling
It is important for the ice maker to be level in order to work
properly. Depending upon where you install the ice maker, you
may need to make several adjustments to level it. You may also
use the leveling legs to lower the height of the ice maker for
undercounter installations.
Tools needed:
Gather the required tools and parts before starting installation.
■ 9" level
■ Adjustable wrench
NOTE: It is easier to adjust the leveling legs if you have another
person to assist you.
1. Move the ice maker to its final location.
NOTE: If this is a built-in installation, move the ice maker as
close as possible to the final location.
2. Place the level on top of the product to see if the ice maker is
level from front to back and side to side.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING
6
3. Push up on the top front of the ice maker, and then locate the
leveling screws that are on the bottom front of the ice maker.
4. Using an adjustable wrench, change the height of the legs as
follows:
■ Turn the leveling leg to the right to lower that side of the
ice maker.
■ Turn the leveling leg to the left to raise that side of the ice
maker.
NOTE: The ice maker should not wobble. Use shims to add
stability when needed.
5. Push up on the top rear of the ice maker and locate the
leveling legs that are on the bottom rear of the ice maker.
6. Follow the instructions in Step 4 to change the height of the
legs.
7. Use the level to recheck the ice maker to see that it is even
from front to back and side to side. If the ice maker is not
level, repeat steps 2 to 5. If the ice maker is level, go to the
“Connect Water Supply” section.
Connect Water Supply
Read all directions before you begin.
IMPORTANT:
■ Plumbing shall be installed in accordance with the
International Plumbing Code and any local codes and
ordinances.
■ Use copper tubing or Whirlpool supply line, Part Number
8212547RP, and check for leaks.
■ Install tubing only in areas where temperatures will remain
above freezing.
Tools needed:
Gather the required tools and parts before starting installation.
■ Flat-blade screwdriver
■ ⁷⁄₁₆" and ¹⁄₂" open-end wrenches or two adjustable wrenches
■ ¹⁄₄" nut driver
NOTE: Do not use a piercing-type or ³⁄₁₆" (4.76 mm) saddle valve
which reduces water flow and clogs more easily.
Connecting the Water Line
1. Turn off main water supply. Turn on nearest faucet long
enough to clear line of water.
2. Using a ¹⁄₂" copper supply line with a quarter-turn shutoff
valve or the equivalent, connect the ice maker as shown.
NOTE: To allow sufficient water flow to the ice maker a
minimum ¹⁄₂" size copper supply line is recommended.
3. Now you are ready to connect the copper tubing. Use ¹⁄₄"
(6.35 mm) OD soft copper tubing for the cold water supply.
■ Ensure that you have the proper length needed for the
job. Be sure both ends of the copper tubing are cut
square.
■ Slip compression sleeve and compression nut on copper
tubing as shown. Insert end of tubing into outlet end
squarely as far as it will go. Screw compression nut onto
outlet end with adjustable wrench. Do not overtighten.
4. Place the free end of the tubing into a container or sink, and
turn on main water supply and flush out tubing until water is
clear. Turn off shutoff valve on the water pipe.
NOTE: Always drain the water line before making the final
connection to the inlet of the water valve to avoid possible
water valve malfunction.
5. Bend the copper tubing to meet the water line inlet which is
located on the back of the ice maker cabinet as shown.
Leave a coil of copper tubing to allow the ice maker to be
pulled out of the cabinet or away from the wall for service.
A. Bulb
B. Nut
A. Compression sleeve
B. Compression nut
C.Copper tubing
A
B
B CA
7
REAR VIEW
6. Remove and discard the short, black plastic tube from the
end of the water line inlet.
7. Thread the nut onto the end of the tubing. Tighten the nut by
hand. Then tighten it with a wrench two more turns. Do not
overtighten.
NOTE: To avoid rattling, be sure the copper tubing does not
touch the cabinet’s side wall or other parts inside the cabinet.
8. Install the water supply tube clamp around the water supply
line to reduce strain on the coupling.
9. Turn shutoff valve ON.
10. Check for leaks. Tighten any connections (including
connections at the valve) or nuts that leak.
Drain Connection
Gravity Drain System
Connect the ice maker drain to your drain in accordance with all
state and local codes and ordinances. If the ice maker is
provided with a gravity drain system, follow these guidelines
when installing drain lines. This will help keep water from flowing
back into the ice maker storage bin and potentially flowing onto
the floor causing water damage.
■ Drain lines must have a minimum of ⁵⁄₈" (15.88 mm) inside
diameter.
■ Drain lines must have a 1" drop per 48" (2.54 cm drop per
122 cm) of run or ¹⁄₄" drop per 12" (6.35 mm per 30.48 cm) of
run and must not have low points where water can settle.
■ The floor drains must be large enough to accommodate
drainage from all drains.
■ The ideal installation has a standpipe with a 1¹⁄₂" (3.81 cm) to
2" (5.08 cm) PVC drain reducer installed directly below the
outlet of the drain tube as shown. You must maintain a
1" (2.54 cm) air gap between the drain hose and the
standpipe.
■ It may be desirable to insulate the drain line thoroughly up to
the drain inlet.
SIDE VIEW
A. Water supply tube clamp
B. Vent hose (drain pump models only)
C. Inlet water tube clamp and supply
line connector
D. Drain hose (drain pump models only)
A. Line to ice maker
B. Nut (purchased)
C. Ferrule (purchased)
D. Supplied line from ice maker
A
C
D
B
DA B C
A. Drain hose
B. 1" (2.54 cm) air gap
C. PVC drain reducer
D. Center of drain should be 23" (58.4 cm) from front of door,
with or without the ³⁄₄" (1.91 cm) panel on the door. The
drain should also be centered from left to right (7
⁵⁄₁₆
"
[18.56 cm] from either side of the ice maker).
1⁷⁄₈"
(4.8 cm)
23"
(58.4 cm)
2" - 1¹⁄₂"
(5 cm - 3.8 cm)
1" (2.54 cm)
A
D
C
B
8
Drain Pump System (on some models)
Connect the ice maker drain to your drain in accordance with the
International Plumbing Code and any local codes and
ordinances.
NOTE: If the drain hose becomes twisted and water cannot
drain, your ice maker will not work.
Connecting the Drain
After ensuring that the drain system is adequate, follow these
steps to properly place the ice maker:
1. Plug into a grounded 3 prong outlet.
2. Style 1 - For gravity drain system, push the ice maker into
position so that the ice maker drain tube is positioned over
the PVC drain reducer. See “Gravity Drain System.”
Style 2 - For drain pump system connect the drain pump
outlet hose to the drain. See “Drain Pump System.”
3. Recheck the ice maker to be sure that it is level. See
“Leveling.”
4. If it is required by your local sanitation code, seal the cabinet
to the floor with an approved caulking compound after all
water and electrical connections have been made.
Ice Maker Door
Tools needed:
Gather the required tools and parts before starting installation.
Remove door
1. Unplug ice maker or disconnect power.
2. Remove the handle screws and handle (on some models).
Keep the parts together and set them aside.
3. Remove the hinge pin from the top hinge.
4. Remove the door from the hinges and screw the top hinge pin
back into the top hinge.
5. Reverse the door end caps as follows:
■ Remove the screw and end cap from the top corner.
Move it diagonally to the opposite side's bottom corner,
keeping the straight side of the end cap facing the front of
the ice maker.
■ Remove the screw and end cap from the bottom corner.
Move it diagonally to the opposite side's top corner,
keeping the straight side of the end cap facing the front of
the ice maker.
6. Set the door aside.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING
WARNING
Excessive Weight Hazard
Use two or more people to move and install ice maker.
Failure to do so can result in back or other injury.
■ ⁵⁄₁₆" wrench ■ Flat putty knife
■ ¹⁄₄" wrench ■ Phillips screwdriver
Hinge pin
⁵⁄₁₆" Hex-head hinge screw
Handle screw End Cap screw
A. Top corner open (no end cap)
B. Beginning top corner end cap
C. Beginning bottom corner end cap
D. Bottom corner open (no end cap)
A
B
D
C
C
D
B
A
9
Reverse Hinges
1. Unscrew and remove the top hinge. Replace the screws in
the empty hinge holes.
2. Remove the screws from the bottom of the opposite side of
the ice maker cabinet. Turn the top hinge upside down so
that the hinge pin points up. Place the hinge on the bottom
opposite side of the ice maker and tighten screws.
3. Remove the plastic hinge pin sleeve from the “old” bottom
hinge and replace it on the new bottom hinge pin.
4. Remove the “old” bottom hinge screws and hinge. Replace
the screws in the empty hinge holes.
5. Remove the screws from the top of the opposite side of the
ice maker cabinet. Turn the hinge upside down so that the
hinge pin points down. Place the hinge on the top opposite
side of the ice maker and tighten the screws.
6. Remove the top hinge pin.
Replace Door
1. Place plastic hinge pin sleeve in the top hinge hole on the
door. Align the door with the top hinge hole and replace the
top hinge pin.
2. Replace the handle and handle screws.
Top Hinge
Bottom Hinge
Reverse Door Catch
1. Remove the hole plugs from the opposite side of the door
and set aside.
2. Remove the screws from the magnetic door catch and
replace it on the opposite side of the door.
3. Push the hole plugs into place on the opposite side of the
door.
4. Plug into a grounded 3 prong outlet.
A. Hinge pin
B. Hinge pin sleeve
C. Hinge
D. Hex-head hinge screw
A. Hex-head hinge screw
B. Hinge pin sleeve
C. Hinge
D. Hinge pin
D
C
B
A
D
C
B
A
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING
10
Normal Sounds
Your new ice maker may make sounds that are not familiar to
you. Because the sounds are new to you, you might be
concerned about them. Most of the new sounds are normal. Hard
surfaces such as floors, walls and cabinets can make the sounds
seem louder than they actually are. The following describes the
kinds of sounds that might be new to you and what may be
making them.
■ You will hear a buzzing sound when the water valve opens to
fill the water reservoir for each cycle.
■ Rattling noises may come from the flow of the refrigerant or
the water line. Items stored on top of the ice maker can also
make noises.
■ The high-efficiency compressor may make a pulsating or high
pitched sound.
■ Water running over the evaporator plate may make a
splashing sound.
■ Water running from the evaporator plate to the water reservoir
may make a splashing sound.
■ As each cycle ends, you may hear a gurgling sound due to
the refrigerant flowing in your ice maker.
■ You may hear air being forced over the condenser by the
condenser fan.
■ During the harvest cycle, you may hear a “thud” when the ice
sheet slides from the evaporator onto the cutter grid.
■ When you first start the ice maker, you may hear water
running continuously. The ice maker is programmed to run a
rinse cycle before it begins to make ice.
ICE MAKER USE
How Your Ice Maker Works
When you first start your ice maker, the water pan will fill and the
system will rinse itself before starting to make ice. The rinsing
process takes about 5 minutes.
Under normal operating conditions, the ice maker will cycle at
preset temperatures. The ice level sensor located in the ice
storage bin will monitor the ice levels.
IMPORTANT:
■ If the water supply to the ice maker is turned off, be sure to
set the ice maker control to OFF.
■ The ice maker is designed to make clear ice from the majority
of water sources on a daily basis. If your results are
unsatisfactory, your water may need to be filtered or treated.
The Ice Making Process
1. Water is constantly circulated over a freezing plate. As the
water freezes into ice, the minerals in the water are rejected.
This produces a sheet of ice with a low mineral content.
2. When the desired thickness is reached, the ice sheet is
released and slides onto a cutter grid. The grid divides the
sheet into individual cubes.
3. The water containing the rejected minerals is drained after
each freezing cycle.
4. Fresh water enters the machine for the next ice making cycle.
5. Cubes fall into the storage bin. When the bin is full, the ice
maker shuts off automatically and restarts when more ice is
needed. The ice bin is not refrigerated, and some melting will
occur. The amount of melting varies with room temperature.
NOTE: As the room and water temperatures vary, so will the
amount of ice produced and stored. This means that higher
operating temperatures result in reduced ice production.
11
Using the Controls
1. To start ice production, press ON.
2. To stop ice maker operation, press OFF.
NOTES:
■ Pressing the On/Off switch does not shut off power to the
ice maker.
■ Allow 24 hours to produce the first batch of ice. Discard
the first batch produced.
Lockout Mode
The control panel can be turned off for easy cleaning or to avoid
unintentional activation by children or small pets.
NOTE: The lock feature does not shut off power to the ice maker
or to the ice maker bin light. It simply deactivates the control
panel.
1. To lock the control panel, press and hold the LOCKOUT
button until the indicator appears.
2. To unlock the control panel, press and hold the LOCKOUT
button until the indicator disappears.
Service Light
The service light indicates when service is needed. If the service
light turns on, turn the ice maker off and back on. If the service
light turns on again, call for service.
Cleaning Needed Status Light
The Cleaning Needed Status light will help you know when it is
time to clean your ice maker. The light will change from green to
yellow. This tells you it is almost time to clean your ice maker. It is
recommended that you clean the ice maker when the status light
changes to red OR ice production decreases significantly. To
clean your ice maker, see “Ice Maker System” in the “Cleaning”
section.
ICE MAKER CARE
Cleaning
The ice making system and the air cooled condenser need to be
cleaned regularly for the ice maker to operate at peak efficiency
and to avoid premature failure of system components. See the
“Ice Maker System” and the “Condenser” sections.
Exterior Surfaces
Wash the exterior enamel surfaces and gaskets with warm water
and mild soap or detergent. Wipe and dry. Regular use of a good
household appliance cleaner and wax will help maintain the
finish. Do not use abrasive cleaners on enamel surfaces as they
may scratch the finish.
For products with a stainless steel exterior, use a clean sponge or
soft cloth and a mild detergent in warm water. Do not use
abrasive or harsh cleaners. Do not use chlorine bleach on
stainless steel surfaces.
Ice Maker System
Minerals that are removed from water during the freezing cycle
will eventually form a hard scaly deposit in the water system.
Cleaning the system regularly helps remove the mineral scale
buildup. How often you need to clean the system depends upon
how hard your water is. With hard water of 15 to 20 grains/gal.
(4 to 5 grains/liter), you may need to clean the system as often as
every 6 months.
NOTE: Use one 16 oz (473 mL) bottle of approved ice maker
cleaner. To order, call 1-800-442-9991 and ask for Part Number
4396808. In Canada, call 1-800-807-6777.
1. Turn off the ice maker.
2. Wait 5 to 10 minutes for the ice to fall into the storage bin.
Remove all ice from the storage bin.
3. Unscrew the drain cap from the bottom of the water pan
located inside the storage bin as shown. Allow the water to
drain completely.
4. Replace the drain cap securely on the water pan. If the drain
cap is loose, water will empty from the water pan and you will
have either thin ice or no ice.
5. Read and follow all handling information on the cleaner bottle
before completing the steps below. Use one 16 oz (473 mL)
bottle of approved ice maker cleaner.
6. Pour one bottle of solution into the water pan. Fill the bottle
twice with tap water and pour it into the water pan.
7. Press the CLEAN button. See “Using the Controls.” The light
will blink, indicating that the cleaning cycle is in process.
When the indicator light turns green (approximately
70 minutes), the cleaning cycle is complete. During the
cleaning cycle, the system will both clean and rinse itself.
8. After the cleaning cycle is complete, remove the drain cap
from the water pan. Look for any cleaning solution left in the
water pan. If cleaning solution drains from the water pan, you
should run the clean cycle again. Be sure to replace the drain
cap securely on the water pan. If the drain cap is loose, water
will empty from the water pan and you will have either thin ice
or no ice.
NOTE: Severe scale buildup may require repeated cleaning with
a fresh quantity of cleaning solution.
9. Press the ON button to resume ice production.
A. Water pan
B. Water pan thumb screws
C. Drain cap
A
B
C
B
12
Condenser
A dirty or clogged condenser:
■ Obstructs proper airflow.
■ Reduces ice making capacity.
■ Causes higher than recommended operating temperatures
which may lead to component failure.
1. Unplug ice maker or disconnect power.
2. Remove the two screws in the lower access panel and the
two screws from the base grille area of the front panel
support.
3. Pull the bottom forward and then pull down to remove the
lower access panel.
4. Remove dirt and lint from the condenser fins and the unit
compartment with a brush attachment on a vacuum cleaner.
5. Replace the lower access panel using the four screws.
6. Plug in ice maker or reconnect power.
Interior Components
1. Unplug ice maker or disconnect power.
2. Open the storage bin door and remove any ice that is in the
bin.
3. Remove the drain cap from the water pan and drain
thoroughly. Replace the drain cap securely on the water pan.
If the drain cap is loose, water will empty from the water pan,
and you will have either thin ice or no ice.
4. Remove the two screws that hold the cutter grid cover in
place and remove the cutter grid cover.
5. Unplug the wiring harness from the left side of the cutter grid.
6. Unplug the ice level sensor from the right side of the cutter
grid. Pull the ice level sensor down and forward away from
the cutter grid.
7. Remove the right-hand and left-hand screws. Lift the cutter
grid up and out.
NOTE: Make sure the plastic spacer from the right-hand side
of the cutter grid bracket stays with the cutter grid.
8. Remove the two thumb screws that hold the water pan in
place. Push down with one hand on the front of the pan while
pulling forward on the bottom back side.
WARNING
Electrical Shock Hazard
Disconnect power before cleaning.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.
A. Cutter grid cover
B. Screws
A. Cutter grid harness
B. Screw
C. Cutter grid
D. Ice level sensor harness
E. Plastic spacer
F. Sc re w
A. Water pan
B. Water pan thumb screws
C. Drain cap
A
B
A
B
C
D
E
F
A
B
C
B
13
9. Remove, clean and replace the ice scoop and ice scoop
holder.
■ After removing the ice scoop, remove the holder by
removing the two thumb screws.
■ Wash the ice scoop holder along with the other interior
components using the following instructions.
■ Replace the ice scoop holder by replacing the thumb
screws.
10. Wash the interior components (cutter grid, exterior of hoses,
and water pan) and the storage bin, door gasket, ice scoop,
and ice scoop holder with mild soap or detergent and warm
water. Rinse in clean water. Then clean the same parts with a
solution of 1 tbs (15 mL) of household bleach in 1 gal. (3.8 L)
warm water. Rinse again thoroughly in clean water.
NOTE: Do not remove hoses. Do not wash plastic parts in
dishwasher. They cannot withstand temperatures above
145°F (63°C).
11. Replace water pan by pushing back on the bottom with one
hand while pushing up and back on the top. Secure the water
pan by replacing both screws.
12. Check the following:
■ Drain cap from the water pan is securely in place. If the
drain cap is loose, water will empty from the water pan,
and you will have either thin ice or no ice.
■ Hose from water pan is inserted into storage bin drain
opening.
13. Slide the cutter grid back into place and secure it by
replacing the right-hand screw and plastic spacer. Then
tighten the left-hand screw. Reconnect the cutter grid
harness and the ice level sensor harness.
14. Replace the plastic cutter grid cover and the two screws.
15. Gently wipe the control panel with a soft, clean dishcloth
using warm water and a mild liquid dish detergent.
16. Plug in ice maker or reconnect power.
17. After cleaning, make sure that all controls are set properly
and that no control indicators are flashing.
Vacation and Moving Care
To shut down the ice maker:
1. Unplug ice maker or disconnect power.
2. Remove all ice from storage bin.
3. Shut off the water supply.
4. Remove the two screws in the lower access panel and the
two screws from the base grille area of the front panel
support. Pull forward to remove the lower access panel.
5. Disconnect the inlet and outlet lines to water valve. Allow
these lines to drain and then reconnect to the valve.
6. Replace lower access panel and screws.
7. Drain water from water pan by removing the drain cap.
8. If the room temperature will drop below 32°F (0°C), water
must be removed from the drain line.
For ice makers with a drain pump installed:
■ Plug in ice maker or reconnect power.
■ Turn ice maker off and remove all remaining ice from ice
bin.
■ Pour 1 qt (0.95 L) of water into the ice bin near the drain
and let the ice maker stand for approximately 5 minutes.
This will allow the water in the bin to drain into the drain
pump so that the pump will remove the remaining water
from the ice bin and the drain pump.
■ Unplug ice maker or disconnect power.
9. Before using again, clean the ice maker and storage bin.
10. Plug into a grounded 3 prong outlet.
NOTE: All components of the ice maker are permanently
lubricated at the factory. They should not require any additional
oiling throughout the normal life of the machine.
A. Thumb screws
B. Ice scoop holder
B
A
WARNING
Electrical Shock Hazard
Disconnect power before servicing.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.
14
TROUBLESHOOTING
Try the solutions suggested here first in order to avoid the cost of an unnecessary service call.
Ice Maker Operation
Your ice maker will not operate
■ Is the power cord plugged in? Plug into a grounded 3 prong
outlet.
■ Is the control set to ON? Be sure that the control is set to
ON.
■ Has a household fuse blown, or has a circuit breaker
tripped? Replace the fuse or reset the circuit breaker. If the
problem continues, call an electrician.
■ Is the room temperature cooler than normal? Room
temperature must be above 55°F (13°C). Otherwise, bin
thermostat may sense cold room temperature and shut off
even though the bin is not full of ice. The ice maker may not
restart once it does shut off.
■ Does the green light come on when the Clean button is
pushed? The ice maker is receiving power but may need
cleaning. See “Cleaning.”
■ Does the ice maker have a drain pump? If there was a large
amount of water added to the ice maker, wait a few minutes
for the drain pump to clear. If there is still water in the bin,
check to see whether the drain hose is kinked.
Ice maker seems noisy
■ Is water being circulated through the ice maker? This is
normal operation. Water is added once per ice-making cycle.
■ Is the water in the reservoir overflowing? This is normal.
This overflow helps to purge minerals that were removed from
the water during the ice making process.
■ Is there a “whooshing” sound? Check the following things:
■ Make sure that the water supply is hooked up and turned
on.
■ Make sure that the drain cap is tight and the water drain
pan pump is securely attached to the water pan.
■ Is there ice between the evaporator plate and the cutting
grid? Check that the ice maker is level. See “Leveling.” If the
ice maker is level, and the problem persists, run a cleaning
cycle. See “Cleaning.”
Ice Production
Ice maker runs but produces no ice
■ Is the control set to ON? Be sure that the control is set to
ON.
■ Is the water supply connected? Make sure the water supply
is properly connected and turned on.
■ Is the drain cap securely in place? If the drain cap is loose,
water will empty from the water pan, and you will have either
thin ice or no ice. Tighten the drain cap.
■ Is there debris in the drain tube? Clean the drain tube.
■ Is there a kink in the drain line? Be sure that there are no
kinks in the line.
■ Is the service light flashing on and off continually? Call for
service.
Ice maker runs but produces very little ice
■ Is the room temperature hotter than normal? Room
temperatures of more than 90°F (32°C) will normally reduce
ice production.
■ Is the condenser dirty? Dirt or lint may be blocking the
airflow through the condenser. See “Condenser” in the
“Cleaning” section.
■ Is there scale buildup in the ice maker? If there is white
scale buildup in the ice maker’s water or freezing system, you
should clean the ice maker. See “Interior Components” in the
“Cleaning” section.
■ Is the drain cap securely in place? If the drain cap is loose,
water will empty from the water pan, and you will have either
thin ice or no ice. Tighten the drain cap if it is loose.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING
WARNING
Electrical Shock Hazard
Disconnect power before servicing.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.
15
Grid is not cutting ice sheets
■ Is the cutter grid securely in place? Check the cutter grid
harness plug to make sure the connection is intact. See
“Interior Components” section of “Cleaning” for instructions
on cutter grid removal.
Ice Quality
Off taste, odor or gray color in the ice
■ Is there unusually high mineral content in the water
supply? The water may need to be filtered or treated.
■ Is there mineral scale buildup? Clean your ice maker. See
“Ice Maker System” in the “Cleaning” section.
■ Are there food items stored in the ice bin? Do not store any
foods in the ice bin.
■ Were all the packaging materials removed? Make sure that
all packaging materials were removed at the time of
installation.
Thin, soft or clumps of ice
■ Is there unusually high mineral content in the water
supply? The water may need to be filtered or treated.
■ Is there mineral scale buildup? Clean your ice maker. See
“Ice Maker System” in the “Cleaning” section.
■ Are there clumps of ice in the bin? If ice is not used
regularly it will melt and form clumps. Break the clumps with
the ice scoop provided.
Plumbing Problems
■ Is the drain hose aligned over the drain? Move the ice
maker to align the drain. See “Connect Water Supply.”
NOTE: Service technicians cannot repair plumbing problems
outside of the ice maker. Call a licensed, qualified plumber.
ASSISTANCE OR SERVICE
Before calling for assistance or service, please check
“Troubleshooting.” It may save you the cost of a service call. If
you still need help, follow the instructions below.
When calling, please know the purchase date and the complete
model and serial number of your appliance. This information will
help us to better respond to your request.
If you need replacement parts
If you need to order replacement parts, we recommend that you
only use FSP
®
replacement parts. FSP
®
replacement parts will fit
right and work right, because they are made with the same
precision used to build every new WHIRLPOOL
®
appliance.
To locate FSP
®
replacement parts in your area, call our Customer
eXperience Center telephone number or your nearest designated
service center.
In the U.S.A.
Call the Customer eXperience Center toll free: 1-800-253-1301.
Our consultants provide assistance with:
■ Features and specifications on our full line of appliances.
■ Installation information.
■ Use and maintenance procedures.
■ Accessory and repair parts sales.
■ Specialized customer assistance (Spanish speaking, hearing
impaired, limited vision, etc.).
■ Referrals to local dealers, repair parts distributors, and
service companies. Whirlpool designated service technicians
are trained to fulfill the product warranty and provide after-
warranty service, anywhere in the United States.
To locate the Whirlpool designated service company in your
area, you can also look in your telephone directory Yellow
Pages.
For further assistance
If you need further assistance, you can write to Whirlpool
Corporation with any questions or concerns at:
Whirlpool Brand Home Appliances
Customer eXperience Center
553 Benson Road
Benton Harbor, MI 49022-2692
Please include a daytime phone number in your correspondence.
In Canada
Call the Whirlpool Canada LP Customer eXperience Centre toll
free: 1-800-807-6777.
Our consultants provide assistance with:
■ Use and maintenance procedures.
■ Accessory and repair parts sales.
■ Referrals to local dealers, repair parts distributors, and
services companies. Whirlpool Canada designated service
technicians are trained to fulfill the product warranty and
provide after-warranty service, anywhere in Canada.
For further assistance
If you need further assistance, you can write to Whirlpool
Canada LP with any questions or concerns at:
Whirlpool Canada LP
Customer eXperience Centre
1901 Minnesota Court
Mississauga, Ontario L5N 3A7
Please include a daytime phone number in your correspondence.
WARNING
Excessive Weight Hazard
Use two or more people to move and install ice maker.
Failure to do so can result in back or other injury.
16
WHIRLPOOL CORPORATION MAJOR APPLIANCE WARRANTY
LIMITED WARRANTY
For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or
furnished with the product, Whirlpool Corporation or Whirlpool Canada LP (hereafter “Whirlpool”) will pay for Factory Specified Parts
and repair labor to correct defects in materials or workmanship. Service must be provided by a Whirlpool designated service company.
This limited warranty is valid only in the United States or Canada and applies only when the major appliance is used in the country in
which it was purchased. Outside the 50 United States and Canada, this limited warranty does not apply. Proof of original purchase date
is required to obtain service under this limited warranty.
ITEMS EXCLUDED FROM WARRANTY
This limited warranty does not cover:
1. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or
repair house fuses, or to correct house wiring or plumbing.
2. Service calls to repair or replace appliance light bulbs, air filters or water filters. Consumable parts are excluded from warranty
coverage.
3. Repairs when your major appliance is used for other than normal, single-family household use or when it is used in a manner that is
contrary to published user or operator instructions and/or installation instructions.
4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in
accordance with electrical or plumbing codes, or use of consumables or cleaning products not approved by Whirlpool.
5. Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage
results from defects in materials or workmanship and is reported to Whirlpool within 30 days from the date of purchase.
6. Any food loss due to refrigerator or freezer product failures.
7. Costs associated with the removal from your home of your major appliance for repairs. This major appliance is designed to be
repaired in the home and only in-home service is covered by this warranty.
8. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.
9. Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an
authorized Whirlpool servicer is not available.
10. The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance
with published installation instructions.
11. Major appliances with original model/serial numbers that have been removed, altered or cannot be easily determined. This warranty
is void if the factory applied serial number has been altered or removed from your major appliance.
The cost of repair or replacement under these excluded circumstances shall be borne by the customer.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED
HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,
ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. WHIRLPOOL SHALL NOT BE LIABLE FOR
INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION
OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES
YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE OR PROVINCE
TO PROVINCE.
If outside the 50 United States and Canada, contact your authorized Whirlpool dealer to determine if another warranty applies.
If you need service, first see the “Troubleshooting” section of the Use & Care Guide. After checking “Troubleshooting,” you may find
additional help by checking the “Assistance or Service” section or by calling Whirlpool. In the U.S.A., call 1-800-253-1301. In Canada,
call 1-800-807-6777.
9/07
Keep this book and your sales slip together for future
reference. You must provide proof of purchase or installation
date for in-warranty service.
Write down the following information about your major appliance
to better help you obtain assistance or service if you ever need it.
You will need to know your complete model number and serial
number. You can find this information on the model and serial
number label located on the product.
Dealer name____________________________________________________
Address ________________________________________________________
Phone number__________________________________________________
Model number __________________________________________________
Serial number __________________________________________________
Purchase date __________________________________________________
17
SÉCURITÉ DE LA MACHINE À GLAÇONS
Risque possible de décès ou de blessure grave si vous ne
suivez pas immédiatement les instructions.
Risque possible de décès ou de blessure grave si vous
ne suivez pas les instructions.
Tous les messages de sécurité vous diront quel est le danger potentiel et vous disent comment réduire le risque de blessure et
ce qui peut se produire en cas de non-respect des instructions.
Votre sécurité et celle des autres est très importante.
Nous donnons de nombreux messages de sécurité importants dans ce manuel et sur votre appareil ménager. Assurez-vous de
toujours lire tous les messages de sécurité et de vous y conformer.
AVERTISSEMENT
DANGER
Voici le symbole d’alerte de sécurité.
Ce symbole d’alerte de sécurité vous signale les dangers potentiels de décès et de blessures graves à vous
et à d’autres.
Tous les messages de sécurité suivront le symbole d’alerte de sécurité et le mot “DANGER” ou
“AVERTISSEMENT”. Ces mots signifient :
IMPORTANTES INSTRUCTIONS DE SÉCURITÉ
AVERTISSEMENT :
Pour réduire le risque d'incendie, de choc électrique ou de blessures lors de l'utilisation
de la machine à glaçons, il convient d'observer certaines précautions élémentaires :
CONSERVEZ CES INSTRUCTIONS
■ Brancher sur une prise à 3 alvéoles reliée à la terre.
■ Ne pas enlever la broche de liaison à la terre.
■ Ne pas utiliser un adaptateur.
■ Ne pas utiliser un câble de rallonge.
■ Utiliser deux ou plus de personnes pour déplacer et
installer la machine à glaçons.
■ Déconnecter la source de courant électrique avant le
nettoyage.
■ Déconnecter la source de courant électrique avant
l'entretien.
■ Replacer pièces et panneaux avant de faire la remise
en marche.
18
INSTRUCTIONS D’INSTALLATION
Déballage de la machine à glaçons
Enlèvement des matériaux d’emballage
Enlever le ruban adhésif et la colle de la machine à glaçons avant
de l’utiliser.
■ Pour enlever ce qui reste du ruban adhésif ou de la colle de la
surface extérieure de la machine à glaçons, frotter la surface
vivement avec le pouce. La colle ou l’adhésif qui reste peut
être facilement enlevé(e) en frottant une petite quantité de
savon à vaisselle liquide sur l'adhésif avec les doigts. Rincer
à l’eau tiède et essuyer.
■ Ne pas utiliser d’instruments acérés, d’alcool à friction, de
liquides inflammables ou de nettoyants abrasifs pour enlever
le ruban adhésif ou la colle. Ne pas utiliser d'eau de Javel sur
les surfaces en acier inoxydable de la machine à glaçons.
Ces produits peuvent endommager la surface de votre
machine à glaçons.
Nettoyage avant l’utilisation
Après avoir enlevé tous les matériaux d’emballage, nettoyer
l’intérieur de la machine à glaçons avant de l’utiliser. Voir les
instructions de nettoyage dans la section “Entretien de la
machine à glaçons”.
Exigences d'emplacement
■ Pour assurer une bonne aération de la machine à glaçons,
l’avant doit être complètement dégagé. Les trois autres côtés
et le dessus de la machine à glaçons peuvent être dissimulés,
mais l’installation doit permettre de tirer la machine à glaçons
vers l’avant pour l'entretien, si nécessaire.
■ Pour installer la machine à glaçons, il faut avoir un tuyau
souple d’alimentation en eau froide de ¹⁄₄" (6,35 mm) de
diamètre extérieur en cuivre avec un robinet d'arrêt et un
système de vidange par gravité ou une pompe à condensats
pour acheminer l’eau vers un drain existant.
■ Choisir un endroit bien aéré où la température est supérieure
à 55°F (13°C) et inférieure à 110°F (43°C). Pour tirer le
meilleur rendement de la machine à glaçons, la température
ambiante doit se situer entre 70°F (21°C) et 90°F (32°C).
■ La machine à glaçons doit être installée à un endroit protégé
contre les éléments comme le vent, la pluie, les embruns ou
les égouttures.
■ Lorsque la machine à glaçons est installée sous un comptoir,
observer les dimensions d'ouverture recommandées
indiquées. Placer les composants électriques et de plomberie
dans la zone recommandée sur l’illustration.
REMARQUES :
■ Vérifier que le cordon d'alimentation n'est pas coincé
entre la machine à glaçons et le placard.
■ Vérifier que la canalisation d'alimentation en eau n'est
pas coincée entre la machine à glaçons et le placard.
■ Vérifier que le conduit de vidange (sur certains modèles)
n'est pas coincé entre la machine à glaçons et le placard.
■ Il est recommandé de choisir un emplacement où le plancher
est de niveau. Il est important que la machine à glaçons soit
d’aplomb pour bien fonctionner. Au besoin, il est possible de
régler la hauteur de la machine à glaçons en changeant la
hauteur des pieds de nivellement. Voir la section
“Nivellement”.
AVERTISSEMENT
Risque du poids excessif
Utiliser deux ou plus de personnes pour déplacer et
installer la machine à glaçons.
Le non-respect de cette instruction peut causer
une blessure au dos ou d'autre blessure.
A. Zone recommandée pour les composants
électriques et de plomberie
B. Niveau du plancher
11¹⁄₂"
(29,2 cm)
15"
(38,1 cm)
24"
(60,1 cm)
9"
(22,9 cm)
28¹⁄₂"
(72,4 cm)
34"
(86,4 cm)
Min.
34
¹⁄₂"
(87,6 cm)
Max.
3¹⁄₂"
(8,9 cm)
B
A
19
Spécifications électriques
Avant de déplacer la machine à glaçons à son emplacement
définitif, il est important de s’assurer que le raccordement
électrique a été fait correctement :
Il faut un circuit d’alimentation électrique CA seulement de
115 volts, 60 Hz, de 15 ou 20 ampères, mis à la terre
conformément aux instructions du Code national de l’électricité
et des codes et règlements locaux.
Il est recommandé de réserver un circuit spécial à la machine à
glaçons. Utiliser une prise où l’alimentation ne peut pas être
coupée à l’aide d’un commutateur ou d'un interrupteur à tirage.
IMPORTANT : Si ce produit est connecté à une prise dotée d'un
disjoncteur de fuite à la terre, un déclenchement intempestif peut
se produire et causer une perte de refroidissement. La qualité
des glaçons peut en être affectée. Si un déclenchement
intempestif se produit et si les glaçons semblent être de piètre
qualité, jeter le tout.
Méthode de mise à la terre recommandée
La machine à glaçons doit être reliée à la terre. La machine à
glaçons comporte un cordon d’alimentation électrique à trois
broches pour la mise à la terre. Le cordon d’alimentation
électrique doit être branché sur une prise de courant murale de
liaison à la terre configuration correspondante, à trois alvéoles,
reliée à la terre conformément au Code national de l’électricité et
aux codes et règlements locaux. S’il n’y a pas de prise de
courant correspondante, il incombe au client de faire installer une
prise de courant murale à trois alvéoles mise à la terre par un
électricien qualifié.
Spécifications de l’alimentation en eau
Une alimentation en eau froide avec une pression entre 30 et
120 lb/po
2
(207 et 827 kPa) est nécessaire pour faire fonctionner
la machine à glaçons. Si vous avez des questions au sujet de la
pression de votre eau, appeler un plombier qualifié agréé.
Alimentation en eau par osmose inverse
IMPORTANT :
■ Les systèmes de filtration de l’eau par osmose inverse
peuvent être utilisés uniquement avec des installations de
machine à glaçons comportant une vidange par gravité. Un
système d’osmose inverse n’est pas recommandé pour les
machines à glaçons équipées d’une pompe de vidange.
■ La pression de l'approvisionnement en eau provenant d’un
système d'osmose inverse allant au robinet d'arrivée d'eau
de la machine à glaçons doit être comprise entre 30 et 120 lb/
po² (207 et 827 kPa).
Si un système de filtration de l’eau par osmose inverse est
raccordé à votre approvisionnement en eau froide, la pression de
l’eau au système d'osmose inverse doit être de 40 à 60 lb/po
2
(276 à 414 kPa) minimum.
REMARQUE : Le système par osmose inverse doit fournir 1 gal.
(3,8 L) d’eau par heure à la machine à glaçons pour un
fonctionnement approprié de la machine à glaçons. Si l’on
souhaite un système d’eau par osmose inverse, il est
recommandé d’utiliser uniquement un système de filtration de
l’eau par osmose inverse central, capable de maintenir
l’approvisionnement régulier en eau requis par la machine à
glaçons. Les systèmes par osmose inverse à capacité de robinet
ne peuvent pas maintenir l’approvisionnement régulier en eau
requis par la machine à glaçons.
Si la pression de l'eau au système d'osmose inverse est
inférieure à 40 à 60 lb/po
2
(276 à 414 kPa) :
■ Vérifier si le filtre à sédiment du système d'osmose inverse
est bloqué et le remplacer si nécessaire.
■ Laisser le réservoir du système d'osmose inverse se remplir
après une utilisation intense.
Si vous avez des questions au sujet de la pression de votre eau,
appeler un plombier qualifié agréé.
Nivellement
Il est important que la machine à glaçons soit d’aplomb pour bien
fonctionner. Selon l’endroit où vous installez la machine à
glaçons, vous pourrez avoir à effectuer plusieurs ajustements
pour la mettre d’aplomb. Vous pouvez également utiliser les
pieds de nivellement pour baisser la hauteur de la machine à
glaçons pour les installations sous comptoir.
Outillage nécessaire :
Rassembler les outils et pièces nécessaires avant de commencer
l’installation.
■ Niveau de 9"
■ Clé à molette
REMARQUE : Il est plus facile d’ajuster les pieds de nivellement
si on se fait aider par une autre personne.
1. Déplacer la machine à glaçons à son emplacement final.
REMARQUE : Dans le cas d'une installation encastrée,
déplacer la machine à glaçons le plus près possible de son
emplacement final.
AVERTISSEMENT
Risque de choc électrique
Brancher sur une prise à 3 alvéoles reliée à la terre.
Ne pas enlever la broche de liaison à la terre.
Ne pas utiliser un adaptateur.
Ne pas utiliser un câble de rallonge.
Le non-respect de ces instructions peut causer
un décès, un incendie ou un choc électrique.
20
2. Placer le niveau sur le dessus du produit pour voir si la
machine à glaçons est d’aplomb d’avant en arrière et
transversalement.
3. Pousser vers le haut sur la partie supérieure avant de la
machine à glaçons pour repérer les vis de nivellement qui se
trouvent sur le fond avant de la machine à glaçons.
4. Au moyen d’une clé à molette, modifier la hauteur des pieds
comme suit :
■ Tourner le pied de nivellement vers la droite pour abaisser
ce côté de la machine à glaçons.
■ Tourner le pied de nivellement vers la gauche pour
soulever ce côté de la machine à glaçons.
REMARQUE : La machine à glaçons ne devrait pas osciller.
Utiliser des cales pour accroître la stabilité au besoin.
5. Pousser vers le haut sur la partie supérieure arrière de la
machine à glaçons pour repérer les pieds de nivellement qui
se trouvent sur le fond arrière de la machine à glaçons.
6. Suivre les instructions de l'étape 4 pour modifier la hauteur
des pieds.
7. Utiliser le niveau pour revérifier que la machine à glaçons est
d’aplomb d’avant en arrière et transversalement. Si elle n’est
pas d’aplomb, répéter les étapes 2 à 5. Si la machine est
d’aplomb, passer à la section “Raccordement à la
canalisation d'eau”.
Raccordement à la canalisation d’eau
Lire toutes les instructions avant de commencer.
IMPORTANT :
■ L'installation de la plomberie doit être conforme au Code
International de plomberie et respecter les codes et
règlements locaux de plomberie.
■ Utiliser un tuyau en cuivre ou le tuyau d'alimentation
Whirlpool, pièce numéro 8212547RP et vérifier s’il y a des
fuites.
■ Installer les tuyaux seulement là où les températures
resteront au-dessus du point de congélation.
Outillage nécessaire :
Rassembler les outils et pièces nécessaires avant de commencer
l’installation.
■ Tournevis à lame plate
■ Clés plates de ⁷⁄₁₆" et de ¹⁄₂" ou deux clés à molette
■ Tourne-écrou de ¹⁄₄"
REMARQUE : Ne pas utiliser de robinet d’arrêt de type perforant
ou à étrier de ³⁄₁₆" (4,76 mm) qui réduit le débit d’eau et qui se
bouche plus facilement.
Raccordement du tuyau d’eau
1. Couper l’alimentation principale en eau. Ouvrir le robinet le
plus proche assez longtemps pour vider l’eau du tuyau.
2. À l’aide d’un tuyau d’alimentation en cuivre de ¹⁄₂" avec une
valve d’arrêt tournée de un quart de tour ou l’équivalent,
raccorder la machine à glaçons tel qu'illustré.
REMARQUE : Pour allouer un débit d’eau suffisant à la
machine à glaçons, un tuyau d’alimentation en cuivre de ¹⁄₂"
est recommandé.
3. On est maintenant prêt à connecter le tuyau en cuivre. Utiliser
un tuyau en cuivre souple de ¼" (6,35 mm) de diamètre
extérieur pour l'alimentation en eau froide.
■ S'assurer d'avoir la longueur nécessaire pour le
raccordement. Il faut s'assurer que les deux extrémités
du tuyau en cuivre sont bien coupées à angle droit.
■ Installer le manchon et l’écrou à compression sur le tuyau
en cuivre (voir l’illustration). Insérer l’extrémité du tuyau
de sortie aussi profondément que possible dans
l’extrémité de sortie et à l’équerre. Visser l’écrou à
compression sur l’extrémité de la sortie à l’aide d’une clé
à molette. Ne pas serrer à l’excès.
4. Placer l'extrémité libre du tuyau dans un contenant ou évier
et rétablir l'alimentation principale en eau pour nettoyer le
tuyau jusqu'à ce que l'eau en sorte claire. Fermer le robinet
d'arrêt sur le tuyau d'alimentation en eau.
REMARQUE : Toujours vidanger le tuyau d'alimentation en
eau avant de faire le raccordement final sur l'entrée du
robinet pour empêcher tout mauvais fonctionnement
éventuel du robinet.
5. Courber le tuyau de cuivre de façon à faire un raccordement
sur l'entrée du robinet qui se trouve à l'arrière de la machine à
glaçons (voir l'illustration). Laisser un serpentin de tube en
cuivre pour permettre de sortir la machine à glaçons du
placard ou du mur en cas d'intervention de service.
A. Renflement
B. Écrou
A. Manchon à compression
B. Écrou de compression
C. Tuyau en cuivre
A
B
B CA
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
Bauknecht GI15NFRTS Le manuel du propriétaire
- Taper
- Le manuel du propriétaire
- Ce manuel convient également à
dans d''autres langues
- English: Bauknecht GI15NFRTS Owner's manual