Nex 720-1046 Le manuel du propriétaire

Marque: Nex

Modèle: 720-1046

Catégorie: Barbecues

Taper: Le manuel du propriétaire

Ce manuel convient également à

730-1046

Questions, problems, missing parts? Before returning to your retailer, call our customer

service department at U.S.A:1-800-913-8999, 8 a.m.-5 p.m., PST, Monday-Friday.

• This instruction manual contains important information necessary for the

proper assembly and safe use of the appliance.

• Read and follow all warnings and instructions before assembling and

using the appliance.

• Keep this manual for future reference.

FOR OUTDOOR USE ONLY

720/730-1046 POUR USAGE EXTÉRIEUR SEULEMENT

EXTERIOR SÓLAMENTE

SERIAL # ____________________ MFG. DATE _____________________ PURCHASE DATE: _____________________

NUMÉRO DE SÉRIE _______________ DATE DE FABRICATION _______________ DATE D'ACHAT _______________

NÚM. DE SERIE ______________ FECHA DE MANUFACTURA ______________ FECHA DE COMPRA ______________

19000856A1

OUTDOOR GAS GRILL

Pages 2 – 23

GRIL À GAZ EXTÉRIEUR

Pages 24-45

PARRILLA DE GAS

PARA EXTERIORES

Páginas 46-67

OWNER’S GUIDE

GUIDE DU PROPRIÉTAIRE

GUÍA DEL PROPIETARIO

Table of Contents

Care and Maintenance . . . . . . . . . . . . . . . . .

Troubleshooting . . . . . . . . . . . . . . . . . . . . . .

Ordering Parts . . . . . . . . . . . . . . . . . . . . . .

Grill Hints . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Grill Cooking Chart . . . . . . . . . . . . . . . . . . .

Grill Recipe Suggestion . . . . . . . . . . . . . . .

Limited Warranty . . . . . . . . . . . . . . . . . . . .

Exploded View . . . . . . . . . . . . . . . . . . . . . .

Part List . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Safety Instruction . . . . . . . . . . . . . . . . . . . . .

Gas Hook–Up . . . . . . . . . . . . . . . . . . . . . . . .

Installer Final Check List. . . . . . . . . . . . . . . .

Leak Testing . . . . . . . . . . . . . . . . . . . . . . . . .

Side Shelf Operating Instructions . . . . . . . . .

Operation Instructions . . . . . . . . . . . . . . . . . .

Lighting Instructions . . . . . . . . . . . . . . . . . . .

Component Identification . . . . . . . . . . . . . . .

Natural Gas Conversion. . . . . . . . . . . . . . . . .

• El presente manual de instrucciones contiene información importante que

lo ayudará a armar el dispositivo correctamente y a utilizarlo de manera

segura.

• Antes de armar y utilizar el dispositivo, lea y siga todas las advertencias e

instrucciones.

• Conserve el presente manual para consultas futuras.

Des questions, des problèmes, des pièces manquantes? Avant de retourner l’article au détaillant,

communiquez avec le service à la clientèle au U.S.A:1-800-913-8999, entre 8 h et 17 h HNP, du lundi

au vendredi et entre 8 h et 12 h, le samedi. Assurez-vous d’avoir votre numéro de série en main. Ce

numéro se situe à l’intérieur de la porte avant de votre barbecue.

• Ce manuel d’instructions contient d’importantes informations essentielles à

un assemblage approprié et sécuritaire de l’appareil.

• Lire et respecter tous les avertissements et toutes les instructions avant

l’assemblage et l’utilisation de l’appareil.

• Conserver ce manuel à titre de référence ultérieure.

¿Consultas, problemas, piezas que faltan? Antes de regresar al vendedor, comuníquese con nuestro

departamento de Servicio al Cliente llamando al U.S.A:1-800-913-8999, de 8 a.m. a 5 p.m. de lunes a

viernes; y de 8 a.m. a 12 p. m. los sábados. Asegúrese de tener disponible el número de serie, que se

encuentra en la parte interna de la puerta frontal de su parrilla.

Safety Instruction

Failure to comply with these instructions could result in a fire or explosion that could cause

serious bodily injury, death, or property damage.

Your grill will be very hot. Never lean over the cooking area while using your grill. Do not

touch cooking surfaces, grill housing, lid or any other grill parts while the grill is in operation,

or until the gas grill has cooled down after use.

In the State of Massachusetts, the following installation instructions apply:

• Installations and repairs must be performed by a qualified or licensed contractor, plumber,

or gasfitter qualified or licensed by the State of Massachusetts.

• If using a ball valve, it shall be a T-handle type.

• A flexible gas connector, when used, must not exceed 3 feet.

DANGER

1. Never operate this appliance unattended.

2. Never operate this appliance within 3.05 m / 10 ft. of any structure, combustible material or

other gas cylinder.

3. Never operate this appliance within 7.62 m / 25 ft. of any flammable liquid.

4. Do not fill cooking vessel beyond maximum fill line.

5. Heated liquids remain at scalding temperatures long after the cooking process. Never

touch cooking appliance until liquids have cooled to 45ºC / 115ºF or less.

6. This appliance is not intended for and should never be used as a heater.

7. If a fire should occur, keep away from the appliance and immediately call your fire

department. Do not attempt to extinguish an oil or grease fire with water.

DANGER

If you smell gas:

• Shut off gas to the appliance.

• Extinguish any open flame.

• Open lid.

• If odor continues, keep away from the

appliance and immediately call your gas

supplier or your fire department.

WARNING

1. Do not store or use gasoline or other

flammable liquids or vapors in the

vicinity of this or any other appliance.

2. An LP cylinder not connected for use

shall not be stored in the vicinity of this

or any other appliance.

CALIFORNIA RESIDENTS ONLY - WARNING: This product and the fuels used to operate

this product (liquid propane), and the products of combustion of such fuels, can expose you to

chemicals including benzene, which is known to the State of California to cause cancer and

reproductive harm. For more information go to: www.P65Warnings.ca.gov.

WARNING

Do not try lighting this appliance without reading the

“LIGHTING INSTRUCTIONS” section of this manual.

CAUTION: Beware of Flashback

TESTED IN ACCORDANCE WITH ANSI Z21.58-2018 •

CSA 1.6-2018 STANDARD FOR OUTDOOR COOKING

GAS APPLIANCE. THIS GRILL IS FOR OUTDOOR USE

ONLY.

CAUTION: Spiders and small insects occasionally

spin webs or make nests in the grill

burner tubes during transit and

warehousing. These webs can lead

to gas flow obstruction, which could

result in a fire in and around burner

tubes. This type of fire is known as

“FLASH-BACK” and can cause serious damage to your

grill and create an unsafe operating condition for the user.

Although an obstructed burner tube is not the only cause of

“FLASH-BACK”, it is the most common cause.

To reduce the chance of “FLASH-BACK”, you must clean

the burner tubes before assembling your grill, and at least

once a month in late summer or early fall when spiders are

most active. Also perform this burner tube cleaning

procedure if your grill has not been used for an extended

period of time. A clogged tube can be lead to a fire

beneath the grill.

Grill Installation Codes

Check your local building codes for the proper method of

installation. in the absence of local codes, this unit should

be installed in accordance with the National Fuel Gas

Code, ANSI Z223.1/NFPA 54, Storage and Handling of

Liquefied Petroleum Gases, ANSI /NFPA B149.2 or CSA

B149.1 Natural Gas and Propane Installation Code, and

the National Electrical Code, ANSI/NFPA 70.

Correct LP Gas Tank Use

LP gas grill models are designed for use with a standard

20 lb. Liquid Propane Gas tank, not included with grill.

Never connect your gas grill to an LP gas tank that

exceeds this capacity.

NOTE: The normal flow of gas through the regulator and

hose assembly can create a humming noise. A low volume

of noise is perfectly normal and will not interfere with

operation of the grill. If humming noise is loud and

excessive you may need to purge air from the gas line or

reset the regulator excess gas flow device. This purging

procedure should be done every time a new LP gas tank is

connected to your grill.

Visually check the burner flames prior to each use. The

flames should look like this picture. If they do not, refer to

the burner main tenancy part of this manual.

304.8 mm

/ 12 in.

469.9 mm

/ 18.5 in.

LP-Gas Supply System

• If the information is not followed

exactly, a fire resulting in death

or serious injury could occur.

• A 20lb tank of approximately 304.8 mm

/ 12 in diameter by 469.9 mm / 18.5 in

high is the maximum size LP gas tank to use.

• The LP gas supply cylinder to be used must be

constructed and marked in accordance with the

specifications for LP –Gas cylinder of the U.S.

Department of Transportation (DOT) or the National

Standard of Canada ,CAN/CSA –B339, Cylinders,

Spheres and Tubes for Transportation of Dangerous

Goods and Commission .

• The LP gas tank must have a shutoff valve terminating

in an LP valve outlet that is compatible with a Type 1. LP

gas supply cylinder must have a shut off valve

terminating in a valve outlet specified for connection type

QCC1 in the standard for compressed gas cylinder valve

outlet and inlet connection ANSI/CGA-V-1 as applicable.

LP gas supply cylinder must be fitted with an Overfill

Protection Device (O.P.D) The LP gas tank must also

have a safety relief device that has a direct connection

with the vapor space of the tank. This safety feature

prevents the tank from being overfilled, which can cause

malfunction of the LP gas tank, regulator and/or grill.

• The tank supply system must be arranged for vapor

withdrawal.

• The LP gas tank used must have a collar to protect the

tank valve.

• Place dust cap on cylinder valve outlet whenever the

cylinder is not in use. Only install the type of dust cap on

the cylinder valve outlet that is provided with the

cylinder valve. Other types of cap or plugs may result in

leakage of propane.

• Never connect an unregulated LP gas tank to your gas

grill.

• This outdoor cooking gas appliance is equipped with a

high capacity hose/regulator assembly for connection to

a standard 20 lb Liquid propane cylinder.

• Have your LP gas tank filled by a reputable propane gas

dealer and visually inspected and re-qualified at each

filling.

• Do not store a spare LP gas cylinder under or near this

appliance.

• Never fill the cylinder beyond 80 percent full.

• Always keep LP gas tanks in an upright position.

• Do not store or use gasoline or other flammable vapors

and liquids in the vicinity of this or any other appliance.

• Storage of an outdoor cooking gas appliance indoors is

permissible only if the cylinder is disconnected and

removed from the outdoor cooking gas appliance.

• When your gas grill is not in use the gas must be turned

off at LP gas tank.

Proper Placement And Clearance Of Grill

• Never use your gas grill in a garage, porch, shed,

breezeway or any other enclosed area. Your gas grill is

to be used outdoors only.

Do Not install this unit into combustible enclosures.

Minimum clearance from sides and back of unit to

combustible construction, 91 cm / 36 in. from sides and

91 cm / 36 in. from back.

• DO NOT use this appliance under overhead combustible

surfaces. This outdoors cooking gas appliance is not

intend to be installed in or on recreational vehicles

and/or boats.

• LP gas tank must be stored outdoors in a well-ventilated

area and out of reach of children. Disconnected LP gas

tanks must not be stored in a building, garage or any

other enclosed area.

• Do Not obstruct the flow of ventilation air around the gas

grill housing. Only use the regulator and the hose

assembly supplied with your gas grill. Replacement

regulators and hose assemblies must be those specified

in this manual.

• The regulator and hose assembly must be inspected

before each use of the grill. If there is excessive

abrasion or wear or if the hose is cut, it must be replaced

prior to the grill being put into operation. The

replacement hose assembly shall be that specified by

the manufacturer.

• Pressure regulator and hose assembly supplied with the

outdoor cooking gas appliance must be used. Never

substitute other types of regulator. Contact customer

service for manufacturer specified replacement parts.

• This outdoor cooking gas appliance is equipped with a

pressure regulator comply with the standard for

Pressure Regulating Valves for LP Gas ANSI/ UL 144.

• Do not use briquettes of any kind in the grill.

• The grill is designed for optimum performance without

the use of briquettes. Do not place briquettes on the

radiant as this will block off the area for the grill burners

to vent. Adding briquettes can damage ignition

components and knobs, and void the warranty.

• Keep the back and side cart free and clear from debris.

Keep any electrical supply cord, or the rotisserie motor

cord away from the heated areas of the grill.

• Never use the grill in extremely windy conditions. If

located in a consistently windy area (oceanfront,

mountaintop, etc.) a windbreak will be required. Always

adhere to the specified clearance.

• Never use a dented or rusty propane tank.

• Keep any electrical supply cord and the fuel supply hose

away from any heated surface.

• While lighting, keep your face and hands as far away

from the grill as possible.

• Burner adjustment should only be performed after the

burner have cooled.

WARNING

Your grill will get very hot. Never lean over the cooking

area while using your grill. Do not touch cooking surfaces,

grill housing, lid or any other grill parts while the grill is in

operation, or until the gas grill has cooled down after use.

Failure to comply with these instructions may result in

serious bodily injury.

CAUTION: TO ENSURE CONTINUED PROTECTION

AGAINST RISK OF ELECTRIC SHOCK, CONNECT TO

PROPERLY GROUNDED OUTLETS ONLY, TO REDUCE

THE RISK OF ELECTRIC SHOCK, KEEP EXTENSION

CORD CONNECTION DRY AND OFF THE GROUND.

WARNING

Keep a spray bottle of soapy water near the gas supply

valve and check the connections before each use.

DO NOT USE ALUMINUM FOIL TO LINE THE GRILL

RACKS OR GRILL BOTTOM.

This can severely upset combustion airflow or trap

excessive heat in the control area.

SAFETY PRACTICES TO AVOID PERSONAL INJURY

When properly cared for your grill will provide safe, reliable

service for many years. However, extreme care must be used

as the grill produces intense heat that can increase accident

potential. When using this appliance basic safety practices

must be followed, including the following:

Do not repair or replace any part of the grill unless

specifically recommended in this manual. All other service

should be referred to a qualified technician.

This grill is not intended to be installed in or on recreational

vehicles or boats.

Children should not be left alone or unattended in an area

where the grill is being used. Do not allow them to sit, stand

or play in or around the grill at any time.

Do not store items of interest to children around or below the

grill.

Do not permit clothing, pot holders or other flammable

materials to come in contact with or too close to any grate,

burner or hot surface until it has cooled. The fabric could

ignite and cause personal injury.

For personal safety, wear proper apparel. Loose fitting

garments or sleeves should never be worn while using this

appliance. Some synthetic fabrics are highly flammable and

should not be worn while cooking.

Only certain types of glass, heat-proof glass ceramic,

earthenware, or other glazed utensils are suitable for grill use.

These materials may break with sudden temperature

changes. Use only on low or medium heat settings in

accordance with the manufacturer’s guidelines.

Do not heat unopened food containers. A build-up of

pressure may cause the containers to burst.

Use a covered hand when opening the grill lid.

Never lean over an open grill.

When lighting a burner, pay close attention to what you are

doing. Make certain you are aware of which burner you are

lighting, so your body and clothing remain clear of open

flames.

WARNING

This outdoor cooking gas appliance is not intended to be

installed in or on boats. And other recreational vehicles.

When using the grill, do not touch the grill rack, burner grate

or immediate surroundings as these areas become

extremely hot and could cause burns. Use only dry

potholders. Moist or damp potholders on hot surfaces may

cause steam burns. Do not use a towel or bulky cloth in

place or potholders. Do not allow potholders to touch hot

portions of the grill rack.

Grease is flammable. Let hot grease cool before attempting

to handle it. Do not allow grease deposits to collect in the

grease tray at the bottom of the grill’s firebox. Clean the

grease tray often

Do not use aluminum foil to line the grill racks or grill bottom.

This can severely upset combustion air flow or trap

excessive heat in the control area.

For proper lighting and performance of the burners keep the

burner ports clean. It is necessary to clean them periodically

for optimum performance. The burners will only operate in

one position and must be mounted correctly for safe

operation.

Clean the grill with caution. To avoid steam burns, do not

use a wet sponge or cloth to clean the grill while it is hot.

Some cleaners produce toxic fumes or can ignite if applied

to a hot surface.

Turn off grill controls and make certain the grill is cool before

using any type of aerosol cleaner on or around the grill. The

chemical that produces the spraying action could, in the

presence of heat, ignite or cause metal parts to corrode.

Do not use the grill to cook excessively fatty meats or other

products which promote flare-ups.

Do not operate the grill under unprotected combustible

constructions. Use only in well ventilated areas. Do not use

in buildings, garages, sheds, breezeways or other such

enclosed areas.

Keep the area surrounding the grill free from combustible

materials including, fluids, trash, and vapors such as

gasoline or charcoal lighter fluid. Do not obstruct the flow of

combustion and ventilation air.

NEVER CONNECT AN UNREGULATED GAS

SUPPLY LINE TO THE APPLIANCE. USE THE

REGULATOR/HOSE ASSEMBLY SUPPLIED.

This is a liquid propane configured grill. Do not attempt

to use a natural gas supply unless the grill has been

reconfigured for natural gas use.

Total gas consumption (per hour) of this stainless

steel gas grill with all burners on high:

Main burner 60,000 Btu/hr

Searing Side Burner 12,000 Btu/hr

Total 72,000 Btu/hr

Gas Hook-Up

L.P. TANK REQUIREMENT

A dented or rusty L.P. tank may be hazardous and

should be checked by your L.P. supplier. Never use a

cylinder with a damaged valve. The L.P. gas cylinder

must be constructed and marked in accordance with

the specifications for L.P. gas cylinders of the U.S.

Department of Transportation (DOT) or the National

Standard of Canada, CAN/CSA-B339, Cylinders,

Spheres and Tubes for Transportation of Dangerous

Goods; and Commission, as applicable. Overfilling

prevention device (OPD) shall be provided on cylinder

& QCCI connection on the cylinder valve, ANSI/CGA-

V-1. The cylinder supply system must be arranged for

vapor withdrawal. The cylinder must include a collar to

protect the cylinder valve. The cylinder must be

provided with a shut off valve terminal in an L.P.

gas supply cylinder valve outlet specified, as applicable,

for connection type QCC1 in the standard for

compressed gas cylinder valve outlet and inlet

connection ANSI/CGA-V-1.

Manifold pressure: 11” water column (W.C.).

L.P. GAS HOOK-UP

Ensure that the black plastic grommets on the LP

cylinder valve are in place and that the hose does not

come into contact with the grease tray or the grill head.

CONNECTION

Your stainless steel grill is equipped with gas supply

orifices for use only with liquid propane gas. It is also

equipped with a high capacity hose/regulator assembly

for connection to a standard 20lb. L.P. cylinder 469.9 mm /

18-1/4 in. high, 304.8 mm / 12-1/4 in. diameter).

To connect the L.P. gas supply cylinder, please follow the

steps below:

1. Make sure tank valve is in its full off position (turn

clockwise to stop)

2. Check tank valve to assure it has proper external

male threads (type 1 connection per ANSIZ21.81)

3. Make sure all burner valves are in their off position.

4. Inspect valve connections, port, and regulator assembly.

Look for any damage or debris. Remove any debris.

Inspect hose for damage. Never attempt to use

damaged or obstructed equipment. See your local L.P.

gas dealer for repair.

5. When connecting regulator assembly to the valve, hand

tighten the quick coupling nut clockwise to a complete

stop. Do not use a wrench to tighten. Use of a wrench

may damage the quick coupling nut and result in a

hazardous condition.

6. Open the tank valve fully (counterclockwise). Apply the

soap solution with a clean brush to all gas connections.

See below. If growing bubbles appear in the solution

the connections are not properly sealed. Check each

fitting and tighten or repair as necessary.

7. If you have a gas connection leak you cannot repair,

turn gas OFF at supply tank, disconnect fuel line from

your grill and call 1-800-913-8999 in USA or your gas

supplier for repair assistance.

8. Also apply soapy solution to the tank seams. See below.

If growing bubbles appear, shut tank OFF and do not

use or move it! Contact an LP gas supplier or your fire

department for assistance.

To disconnect L.P. gas cylinder:

1. Turn the burner valves off.

2. Turn the tank valve off fully (turn clockwise to stop).

3. Detach the regulator assembly from the tank valve by

turning the quick coupling nut counterclockwise.

Installer Final Check List

USER, PLEASE RETAIN THIS MANUAL FOR FUTURE

REFERENCE.

PROPANE CYLINDER CAUTIONS

a) Do Not store a spare LP-gas cylinder under or near

this appliance.

b) NEVER fill the cylinder beyond 80 percent full.

c) If the information in “a” and “b” is not followed

exactly, a fire or explosion causing death or serious

injury may occur.

✓ Minimum clearance from sides and back of unit to

combustible construction, 91 cm / 36 in. from sides

and 91 cm / 36 in. from back

✓ All internal packaging removed.

✓ Knobs turn freely.

✓ Burners are tight and sitting properly on orifices.

✓ Pressure regulator connected and set. Gas

connections to grill using hose & regulator

assembly provided (pre-set for 11 in. water column).

✓ Unit tested and free of leaks.

✓ User informed of gas supply shut off valve location

GENERAL

Although all gas connections on the grill are leak tested at

the factory prior to shipment, a complete gas leak test check

must be performed at the installation site due to possible

mishandling in shipment, or excessive pressure unknowingly

being applied to the unit. Periodically check the whole system

for leaks following the procedures listed

below. If the smell of gas is detected at anytime you

should immediately check the entire system for leaks.

BEFORE TESTING

Make sure that all packing material is removed from the grill

including tie-down straps.

DO NOT SMOKE WHILE LEAK TESTING.

NEVER PERFORM LEAK TEST WITH AN OPEN

FLAME.

Make a soap solution of one part liquid detergent and one

part water. You will need a spray bottle, brush, or rag to

apply the solution to the fittings. For the initial leak test, make

sure the L.P. cylinder is 80% full.

TO TEST

1. Make sure the control valves are in the “○” position, and

turn on the gas supply.

2. Check all connections from the L.P. gas regulator and

supply valve up to and including the connection to the

manifold pipe assembly (the pipe that goes to the

burners). Soap bubbles will appear where a leak is

present.

3. If a leak is present, immediately turn off the gas supply

and tighten the leaky fittings.

4. Turn the gas back on and recheck.

5. Should the gas continue to leak from any of the fittings,

turn off the gas supply and contact customer service at

1-800-913-8999 in USA.

Leak Testing

ALWAYS CHECK FOR LEAKS AFTER EVERY L.P.

TANK CHANGE

Check all gas supply fittings for leaks before each use.

It is handy to keep a spray bottle of soapy water near

the shut-off valve of the gas supply line. Spray all the

fittings. Bubbles indicate leaks.

5. Should the gas continue to leak from any of the fittings,

turn off the gas supply and contact customer service at

1-800-913-8999 in USA.

Only those parts recommended by the manufacturer should

be used on the grill.

Substitution will void the warranty. Do not use the grill until all

connections have been checked and do not leak.

GAS FLOW CHECK

Each grill burner is tested and adjusted at the factory prior to

shipment; however, variations in the local gas supply may

make it necessary to adjust the burners. The flames of the

burners should be visually checked.

Flames should be blue and stable with no yellow tips,

excessive noise or lifting. If any of these conditions exist,

check to see if the air shutter or burner ports are blocked by

dirt, debris, spider webs, etc. If you have any questions

regarding flame stability, please call customer service at 1-

800-913-8999 in USA.

Side Shelf Operation Instructions

HOW TO EXTEND THE SIDE SHELF

Step 1. Lift the side shelf straight up using the handle. Side

shelf will lock in place automatically.

NOTE: Make sure that the shelf is firmly locked in the

open position before placing any items on it.

HOW TO COLLAPSE THE SIDE SHELF

Step 1. Pull up on the side shelf while pushing both side shelf

support rods in.

Step 2. Slowly guide the side shelf down into folded position.

Operating Instructions

GENERAL USE OF THE GRILL AND ROTISSERIE

Each main burner is rated at 10,000 BTU/HR. The main

grill burners encompass the entire cooking area and are

side ported to minimize blockage from falling grease and

debris. The knobs are located on the lower center portion of

the control panel. Each knob is labeled on the control panel.

USING THE GRILL

Grilling requires high heat for searing and proper browning.

Most foods are cooked at the high heat setting for the entire

cooking time. However, when grilling large pieces of meat or

poultry, it may be necessary to turn the heat to the lower

setting after the initial browning. This cooks the food through

without burning the outside. Foods cooked for a long time or

foods basted with a sugary marinade may need the lower

heat setting near the end of the cooking time.

NOTE: This grill is designed to grill efficiently without the

use of lava rocks or briquettes of any kind. Heat is radiated

by the stainless steel flame tamers positioned above each

burner.

NOTE: The hot grill sears the food, sealing in the juices. The

more thoroughly the grill is preheated, the faster the meat

browns and the darker the grill marks.

DO NOT LEAVE THE GRILL UNATTENDED WHILE

COOKING.

WARNING: IMPORTANT!

USING THE SIDE BURNER

Inspect the gas supply hose prior to turning the gas “ON”. If

there is evidence of cuts, wear or abrasion, it must be

replaced prior to use. Do not use the side burner if the odor

of gas is present.

Lighting Instructions

WARNING: IMPORTANT!

BEFORE LIGHTING

Inspect the gas supply hose prior to turning the gas “ON”. If

there is evidence of cuts, wear, or abrasion, it must be

replaced prior to use. Do not use the grill if the odor of gas is

present. Only the pressure regulator and hose assembly

supplied with the unit should be used.

Never substitute regulators and hose assembly for those

supplied with the grill. If a replacement is necessary, contact

the manufacturer for proper replacement. The replacement

must be that specified in the manual.

TO LIGHT THE MAIN/SIDE BURNER

Make sure all knobs are off then turn on the gas supply from

the LP (Liquid Propane) tank. Always keep your face and

body as far from the grill as possible when lighting.

For outdoor grills using gas supply source other than a 9.07

kg / 20 lb LP gas fuel tank, open the manual shutoff valve in

the gas supply line. The valve is open when the handle is

parallel to the gas pipe.

To light your main burner, push and turn main burner

control knob to , at the same time, press and hold

electronic ignition button to light the burner. Once the burner

is lit, release the electronic ignition button and knob. If the

burner does not light wait 5 minutes for any excess gas to

dissipate and then retry.

WARNING

Always keep your face and body as far away from the

burner as possible when lighting.

Each burner is adjusted prior to shipment;

however, variations in the local gas supply may

make minor adjustments necessary.

Keep a spray bottle of soapy water near the gas

supply valve and check the connections before

each use.

Do not attempt to light the grill if odor of gas is

present. Call for service 1-800-913-8999.

CAUTIONS

Place dust cap on cylinder valve outlet when the

cylinder is not in use. Only install the type of dust cap

on the cylinder valve outlet that is provided with the

cylinder valve. Other types of caps or plugs may

result in leakage of propane.

The gas must be turned off at the supply cylinder

when the unit is not in use.

If the appliance is stored indoors the cylinder must be

disconnected and removed from the appliance.

Cylinders must be stored outdoors in a well-ventilated

area out of the reach of children.

A. Closed valve

B. Open valve

Main burner

Side burner

Match Light

1. If the burner will not light after several attempts

then the burner can be match lit, before using the

match allow 5 minutes for any accumulated gas to

dissipate.

2. Clip a match on one end of the lighting rod.

3. Light match.

4. Hold lighting rod and insert lighted match right

next to the burner ports or ceramic file.

5. Push and turn the designated control knob to .

6. Burner should ignite immediately.

Component Identification

Note: Remove all packaging, including straps, before using the grill

Side BurnerMain Burner

Control Knob, Label

Orifice Chart

The different burner valves in this grill have different BTU ratings. This means that the amount of gas coming from each orifice

varies in order to create the BTU's. The holes in the orifices themselves are drilled to different sizes so as to allow the proper

amount of gas to flow through them. Please note the chart below as an easy reference for the various orifice opening sizes for

the different valves in the grill.

720-1046 (LP), 730-1046 (NG) orifice sizes

Liquid Propane (LP) Natural Gas (NG)

Components Orifice Size BTU/HR Orifice Size BTU/HR

Main Burner 1.02 mm 12,000 1.70 mm 12,000

Side Burner 1.02 mm 12,000 1.70 mm 12,000

Below parts are needed for natural gas conversion:

INCLUDED

• Natural gas orifices

Natural gas conversion kit Part Number 710-0003

(NOT INCLUDED)

• Quick Connector

• 3.04 m / 10 ft Natural Gas Hose

• 4” Water Column Regulator with Hose

• Tools

• 6 mm Nut Driver

• 6 mm Wrench

• Hex Key

6mm

Tools that will be needed for conversion:

House

Supply Line

Quick Connector

3.0 m NG

Hose

4” WC

Regulator

with Hose

Gas Grill

Connection

Natural Gas Conversion

WARNING

This conversion kit shall be installed by a qualified service agency in accordance with

the manufacturer’s instructions and all applicable codes and requirements of the

authority having jurisdiction. If the information in these instructions is not followed

exactly, a fire, explosion or production of carbon monoxide may result causing

property damage, personal injury or loss of life. The qualified service agency is

responsible for the proper installation of this kit. The installation is not proper and

complete until the operation of the converted appliance is checked as specified in the

manufacturer’s instructions supplied with the kit.

Make Gas Connection

1. Before making any connections, check to ensure the

natural gas inlet pressure falls between the allowable

range of 7" W.C. / 0.25 psi and 14" W.C. / 0.5 psi. If the

NG inlet pressure does not fall within this range, contact

your local gas supplier.

2. A combination of pipe fittings must be used to connect

the grill to the existing gas line.

• The 3.04 m / 10 ft PVC flexible gas supply hose

design certified by CSA must be used.

• Pipe-joint compounds suitable for use with Natural

gas must be used. Do not use Teflon®+ tape.

• There must be a certified manual shut-off valve in the

gas supply line near the grill for easy access.

3. Connect the brass connector on one end of the 3.04 m /

10 ft PVC flexible gas supply hose to the Natural gas

pressure regulator.

4. Connect the quick connector on the other end of the

3.04 m / 10 ft PVC flexible gas supply hose to the rigid

natural gas supply pipe.

5. Please do leak test after conversion. See page 8.

a. The outdoor cooking gas appliance and its

individual shutoff valve must be disconnected from

the gas supply piping system during any pressure

testing of that system at test pressure in excess of

3.5kPa / 0.5 psi.

b. The outdoor cooking gas appliance must be

isolated from the gas supply piping system by

closing its individual manual shutoff valve during

any pressure testing of the gas supply piping

system at test pressures equal to or less than

3.5kPa / 0.5 psi.

Installing the Natural gas regulator

1. Turn off the main gas supply valve.

2. Disconnect 20 lb LP gas fuel tank (if present).

3. Turn off all burner control valves.

4. Remove the 20 lb LP gas fuel tank (if present) from the

grill cart.

5. Use an adjustable wrench to remove the LP regulator

from the manifold.

6. Use an adjustable wrench to install the Natural gas

regulator hose to the manifold and secure. Attach the

Natural gas regulator to the side panel inside the grill cart

with the two screws that are preassembled on the

regulator.

† ®TEFLON is a registered trademark of Chemours.

5. Replace with the natural gas orifice.

IMPORTANT: Check that the orifice is properly installed

inside of the burner opening.

6. Reinsert the burner and reattach using the pin

previously removed. Repeat the procedure for each

main burner.

7. Position the igniters so they are 1/8" (3.2 mm) away

from each burner.

Change Main Burner Valve Orifices

1. Remove the grates and flame tamers.

2. Remove the screw and the pin that hold the burner in

place. Set aside the screw and pin.

3. Remove the burner from the grill by lifting the burner out.

4. Use a 6 mm socket and wrench or 6 mm nut driver to

remove the brass orifice from the end of gas valve.

Change the Side Burner Orifice

1. Remove the two screws which were pre-assembled on

side burner tube, and the igniter wire from side burner

tube.

2. Lift side burner tube out from side burner firebox, as

shown below.

3. Use 6 mm socket wrench or 6 mm nut driver to remove

the orifice. Replace with the natural gas orifice.

IMPORTANT: Check that the orifice is properly

installed inside of the valve.

4. Reinstall the side burner. Install and tighten the two

screws and reconnect the igniter wire.

5. Open the manual shutoff valve in the gas supply. The

valve is open when the handle is parallel to the gas pipe.

6. Test all connections using an approved noncorrosive

leak- detection solution. Bubbles will show a leak.

Correct any leak found.

7. For normal operating sequence of the ignition system,

see “Lighting Instructions” on page 9.

4. Replace the control knob and turn off the burner.

5. Repeat steps 2 through 4 for each burner if needed.

6. Replace the flame tamers and grates after the burners

have been cooled.

Record Conversion

The LP appliance nameplate is located inside the grill cabinet

on the left-hand side. Once converted, place the NG

appliance nameplate as close as possible to the current LP

appliance nameplate without covering it.

In the last page of the Use and Care Guide, write “Converted

to Natural Gas”. Also record the conversion date and the

technician/company that performed the conversion.

Adjust High/Low Flame Setting Screw

When converting from LP to Natural gas, you will need to

adjust the high flame setting screw for ideal burner flame

height.

The flames of the grill burners and side burners (on some

models) should be blue and stable with no excessive noise or

lifting (LP gas flames will have a slightly yellow tip). A yellow

flame indicates not enough air. If flame is noisy or lifts away

from the burner, there is too much air. Some yellow tips on

flames when the burner is set to HIGH setting are acceptable

as long as no carbon or soot deposits appear. The flames

should be approximately 2.54 cm / 1 in high.

1. Remove each control knob for the main burners and side

burner.

2. Use a flat-blade screwdriver to turn the high flame set

screw clockwise approximate 90º.

3. Check that burner operates at the new high flame setting.

It may be necessary to adjust the screw setting slightly

more to get the ideal burner flame height.

2.54 cm / 1 in

Care and Maintenance

Warning: If you wish to replace main burner, we

strongly recommend that you hire a professionally

trained technician to replace it. Please understand that

we will not be responsible for any liability, personal

injury, or property damage resulting from an

improperly assembled burner.

STAINLESS STEEL

There are many different stainless steel cleaners available.

Always use the mildest cleaning procedure first, scrubbing

in the direction of the grain. Do not use steel wool as it will

scratch the surface. To touch up noticeable scratches in the

stainless steel, sand very lightly with dry 100 grit emery

paper in the direction of the grain. Specks of grease can

gather on the surfaces of the stainless steel and bake on to

the surface and give the appearance of rust. For removal

use a mild abrasive pad in conjunction with a stainless steel

cleaner.

GRILL GRATE

The easiest way to clean the grill is immediately after

cooking is completed and after turning off the flame. Wear a

barbeque mitt to protect your hand from the heat and steam.

Dip a brass bristle barbeque brush in water and scrub the

hot grill. Dip the brush frequently in the bowl of water.

Steam, created as water contacts the hot grill, assists the

cleaning process by softening any food particles. If the grill

is allowed to cool before cleaning, cleaning will be more

difficult.

ENSURE THAT THE GAS SUPPLY AND THE KNOBS

ARE IN THE “○” POSITION. MAKE SURE THE RANGE

TOP BURNER IS COOL BEFORE REMOVAL.

GRILL BURNERS

Extreme care should be taken when moving a burner as it

must be correctly centered on the orifice before any attempt

is made to relight the grill. Frequency of cleaning will

depend on how often you use the grill.

MAIN BURNER CLEANING

Ensure the gas supply is off and the knobs are in the “○”

position. Make sure the grill is cool. Clean the exterior of the

burner with a wire brush. Clear stubborn scale with a metal

scraper. Clear any clogged ports with a straightened paper

clip. Never use a wooden toothpick as it may break off and

clog the port. Please note if insects or other obstructions are

blocking the flow of gas through the burner, and if so you

will need to call our customer service line at 1-800-913-8999

in USA.

GREASE TRAY CLEANING

The grease tray should be emptied and wiped down

periodically and wash with a mild detergent and warm water

solution. A small amount of sand may be placed in bottom

of grease tray to absorb the grease. Check the grease tray

frequently, do not allow excess grease to accumulate and

overflow out of the grease tray.

HOW TO REPLACE MAIN BURNER

Step 1. Remove the main burner “R” pin on the back wall

of fire box by using needle nose pliers. Use a flathead

screwdriver to remove burner pin cover, then remove the

burner on the front wall of fire box, as shown below.

Step 2. Insert the burner onto the orifice and secure the

burner pin cover on the burner, as shown below, make

sure burner hole aim at orifice .

Step 3. Secure the main burner on the back wall of fire box

with “R” Pin.

CAUTION

1. Keep outdoor cooking gas appliance area clear and

free from combustible materials, gasoline and other

flammable vapors and liquids.

2. Do not obstruct the flow of combustible and ventilation

air.

3. Keep the ventilation openings of the cylinder enclosure

free and clear from debris.

Troubleshooting

SPIDER AND INSECT WARNING

Checking and cleaning burner/ venturi tubes for insects and

insect nests. A clogged tube can lead to a fire beneath the

grill.

Although an obstructed burner tube is not the only cause of

“FLASH-BACK”, it is the most common cause.

To reduce the chance of “FLASH-BACK”, you must clean the

burner tubes before assembling your grill, and at least once a

month in late summer or early fall when spiders are most

active. Also perform this burner tube cleaning procedure if

your grill has not been used for an extended period of time.

WHEN TO LOOK FOR SPIDERS

You should inspect the burners at least once a year or

immediately after any of the following conditions occur:

1. The smell of gas in conjunction with the burner flames

appearing yellow.

2. The grill does not reach temperature.

3. The grill heats unevenly.

4. The burners make popping noises.

BEFORE CALLING FOR SERVICE

If the grill does not function properly, use the following check

list before contacting your dealer for service. You may save

the cost of a service call.

PREHEATING: The grill lid should be in a closed position

during the preheat time period. It is necessary to preheat the

grill before cooking certain foods, depending on the type of

food and the cooking temperature. Food that requires a high

cooking temperature needs a pre-heat

period of five minutes; food that requires a lower cooking

temperature needs only a period of two to three minutes.

COOKING TEMPERATURES

High setting-Use this setting for fast warm-up, for searing

steaks and chops, and grilling.

Low setting-Use this setting for all roasting, baking, and when

cooking very lean cuts such as fish.

These temperatures vary with the outside temperature and

the amount of wind.

Cooking with in-direct Heat: You can cook poultry and large

cuts of meat slowly to perfection on one side of the grill by

indirect heat from the burner on the other side. Heat from the

lit burner circulates gently throughout the grill, cooking the

meat or poultry without any direct flame touching it. This

method greatly reduces flare-ups when cooking extra fatty

cuts, because there is no direct flame to light the fats and

juices that drip down during cooking.

CAUTION: If burners go out during operation, close gas

supply at source, and turn all gas valves off. Open lid and

wait five minutes before attempting to relight (this allows

accumulated gas fumes to clear).

CAUTION: Should a grease fire occur, close gas supply at

source, turn off all burners and leave lid closed until fire is out.

CAUTION: DO NOT attempt to disconnect any gas fitting

while your grill is in operation. As with all appliances, proper

care and maintenance will keep them in top operating

condition and prolong their life. Your gas gill is no exception.

CAUTION: Side burner lid will get hot if used when lid is

closed.

PROBLEM SOLUTION

When attempting to light my grill, it will

not light immediately.

Make sure you have a spark while you are trying to light the burner (if no

spark) . Check if the battery is installed properly.

Ensure that the wire is connected to the electrode assembly.

Clean wire (s) and / or electrode with rubbing alcohol and a clean swab. Wipe

with a clean cloth.

Check to see if the other burners operate. If so. Check the gas orifice on the

malfunctioning burner for an obstruction.

Rotisserie burner will not light when the

igniter button is pushed.

Check to see if debris is blocking the electrode.

Check to see if there is a spark that jumps to the burner from the electrode. If no

spark is seen, check the battery located inside the igniter box. To open turn

counter

Does the infrared back burner light when attempting to light with a match ? If not,

check to ensure the gas is on.

Regulator makes noise. Vent hose on the regulator may be plugged or regulator may be faulty. Ensure

the vent hole on the regulator is not obstructed. Clear the hole, close the gas

control valves. Wait ten minutes and re-start.

Check your flames for proper performance. If the flames are not correct,

replace regulator.

Full size cover does not fit the grill. Cover may be incorrect for your grill. It may be a tight fit.

Ensure the cover is the correct length for your grill.

Measure it left to right. Compare to the grill’s measurement.

Compare the location and size of the hood portion of the cover to your grill.

Spread the cover and allow it to relax, preferably in warm sunlight or in a warm

room.

For grill with a side shelf bunch the cover like a sock, put on left to right.

PROBLEM SOLUTION

Rotisserie motor will not turn Ensure the motor is connected to a properly grounded power supply.

Ensure the on / off switch is in the on position.

Ensure that the spit is fully inserted into the rotisserie motor.

Ensure that the load does not exceed the 40 pounds operational capacity.

Ensure that there is no encumbrance or drag.

Grill only heats to 93-149°C / 200-300°F.

Check to see if the fuel hose is bent or kinked.

Make sure the grill area is clear of dust.

Make sure the burner and orifices are clean.

Check for spiders and insects.

The regulator has a safety device that restricts the flow of gas in the event of a

leak. This safety device can be triggered without a gas leak. To reset the

safety device, turn off all burners and close the LP tank valve. Disconnect the

regulator from the LP tank and wait one minute. Reconnect the regulator to the

LP tank and slowly open the LP tank valve until the valve is fully open. Light all

burners and observe the temperature.

Grill takes a long time to preheat.

Normal preheat 260-316°C / 500-600°F, takes about 10-15 min. Cold weather

and wind may effect your preheat time.

If you are using volcanic rock or briquettes they can increase the preheat time

and maximum temperature.

Burner flames are not light blue. Too much or not enough air for the flame.

Elevation is the principal cause, however cold weather can affect the mixture.

Burner adjustment may be required.

Grill is in a windy location.

Ordering Parts

HOW TO ORDER REPLACEMENT PARTS

To make sure you obtain the correct replacement part (s) for

your gas grill, please refer to the parts list on pages 69. The

following information is required to assure getting the correct

part. Please note the shipping cost for the delivery of any

replacement parts will be on yourself.

• Gas grills model number (see data sticker on grill).

• Part number of replacement part needed.

• Description of replacement part needed.

• Quantity of parts needed.

To obtain replacement parts, contact our customer

service hotline, U.S.A: 1- 800-913-8999.

IMPORTANT

Use only factory authorized parts. The use of any part

that is not factory authorized can be dangerous. This

will also void your warranty.

Keep this assembly and operating instruction manual

for convenient referral, and for replacement parts

ordering.

Grill Hints

The doneness of meat, whether rare, medium, or well done,

is affected to a large degree by the thickness of the cut.

Expert chefs say it is impossible to have a rare doneness

with a thin cut of meat.

The cooking time is affected by the kind of meat, the size and

shape of the cut, the temperature of the meat when cooking

begins, and the degree of doneness desired.

When defrosting meats it is recommended that it be done

overnight in the refrigerator as opposed to a microwave. This

in general yields a juicier cut of meat.

Use a spatula instead of tongs or a fork to turn the meat, as

a spatula will not puncture the meat and let the juices run out.

To get the juiciest meats, add seasoning or salt after the

cooking is finished on each side and turn the meat only once

(juices are lost when the meat is turned several times). Turn

the meat just after the juices begin to bubble to the surface.

Trim any excess fat from the meat before cooking. To

prevent steaks or chops from curling during cooking, slit the

fat around the edges at 51mm / 2-in. intervals.

DO NOT LEAVE THE GRILL UNATTENDED WHILE

COOKING.

FOOD

WEIGHT OR

THICKNESS

HEAT

SETTING

APPROXIMATE

TIME

SPECIAL INSTRUCTIONS

AND TIPS

Vegetables

Slice. Dot with butter or margarine. Wrap in

heavy -duty foil. Grill, turning occasionally.

Fresh Beets

Carrots

Turnips

Medium 12 to 20 minutes

Grill, turning once. Brush occasionally with

melted butter or margarine.

Onion

1.3mm / 1/2 in.

slices

Medium 8 to 20 minutes

Season with Italian dressing, butter, or

margarine.

Potatoes Sweet

White

Whole

170 to 226g

/ 6 to 8 oz

Medium

High

40 to 60 minutes

45 to 60 minutes

Wrap individually in heavy - duty foil. Grill,

rotating occasionally.

Frozen Asparagus

Peas Green beans

Sprouts

Medium 15 to 30 minutes

Dot with butter or margarine.

Wrap in heavy -duty foil. Grill, turning

occasionally.

French fries Medium 15 to 30 minutes

Place in aluminum foil pan.

Grill, stirring occasionally

Meats

Beef

Hamburgers

1-2 cm

/ 1/2 - 3/4 in.

Medium 10 to 18 minutes

Grill, turning once when juices rise to the

surfaces.

Do not leave hamburgers unattended since a

flare-up could occur quickly. Cook to internal

temperature of 160 degrees

Tenderloin High 8 to 15 minutes

Rare 2.5 cm / 1 in. High 8 to 14 minutes

Trim edges. Grill, turning once

Medium

1.3 cm / 1/2 in.

2.5 cm / 1 in.

2.5 - 3.8 cm

/ 1-1/2 in.

High

Medium

to High

11 to 18 minutes

12 to 22 minutes

16 to 27 minutes

Well - done

2.5 cm / 1 in.

2.5 - 3.8 cm

/ 1-1/2 in.

Medium

18 to 30 minutes

16 to 35 minutes

Lamb

Chop & Steaks

Rare

2.5 cm / 1 in.

2.5 - 3.8 cm

/ 1-1/2 in.

Medium

High

10 to 15 minutes

14 to 18 minutes

Trim edges. Grill, turning once.

Medium

2.5 cm / 1 in.

2.5 - 3.8 cm

/ 1-1/2 in.

Medium

High

13 to 20 minutes

18 to 25 minutes

Pork

Chops

2.5 cm / 1 in. Medium

20 to 30 minutes

Trim edges. Grill, turning once. Cook to

desired

doneness.

Well -done

2.5 - 3.8 cm

/ 1-1/2 in.

Medium 30 to 40 minutes

Grill Cooking Chart

FOOD

WEIGHT OR

THICKNESS

HEAT

SETTING

APPROXIMATE

TIME

SPECIAL INSTRUCTIONS

AND TIPS

Ribs Medium

30 to 40

minutes

Grill, turning occasionally.

During last few minutes brush with barbecue

sauce. Turn several times.

Ham steaks

(precooked)

2.5 cm / 1 in.

slices

High 4 to 8 minutes Trim edges. Grill, turning once.

Hot dogs Low 5 to 10 minutes Slit skin. Grill, turning once.

Poultry 900 to 1400 g

/ 2 to 3 lb

Low

Medium

Up to 1 hour

Place skin side up. Grill, turning and

brushing frequently with melted butter,

margarine, oil or marinade.

Breasts

well –done

Medium

30 to 45

minutes

Marinate as desired.

Fish and

Seafood

Halibut

Salmon

Swordfish

2 to 2.5 cm

/ 3/4 to 1 in.

Medium

High

8 to 15 minutes

Grill, turning once. Brush with melted butter,

margarine or oil to keep moist.

Whole

Catfish

Rainbow trout

113 to 226 g

/ 4 to 8 oz

Medium

High

12 to 20

minutes

Grill, turning once. Brush with melted butter,

margarine or oil. Brush with melted butter

and lemon juice.

La page charge ...

Nex 720-1046 Le manuel du propriétaire

Marque: Nex

Modèle: 720-1046

Catégorie: Barbecues

Taper: Le manuel du propriétaire

Ce manuel convient également à

730-1046

Télécharger le PDF

rapport

dans d''autres langues

English: Nex 720-1046 Owner's manual
español: Nex 720-1046 El manual del propietario

Nex 720-1046 Le manuel du propriétaire

Ce manuel convient également à

Nex 720-1046 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents