Rockford Fosgate Fanatic X FNX2614 Installation & Operation Manual

Marque: Rockford Fosgate

Modèle: Fanatic X FNX2614

Catégorie: Haut-parleurs de voiture

Taper: Installation & Operation Manual

Ce manuel convient également à

FNX2414

FNX2514

FNX2614U

FNX2614

Installation

& Operation

Páginas de Referencia para la Instalación

Schéma d’Installation

Installations Beiblatt

Istruzioni di Installation

COMPONENT SYSTEM

– i –

Dear Customer,

Congratulations on your purchase of the world's finest brand of car audio speakers.

At Rockford Fosgate, we are fanatics about musical reproduction at its best, and we

are pleased you chose our product. Through years of engineering expertise, hand

craftsmanship, and critical testing procedures, we have created a wide range of

products that reproduce music with all the clarity and richness you deserve.

For maximum performance, we recommend you have your new Rockford Fosgate

product installed by an Authorized Rockford Fosgate Dealer, as we provide special-

ized training through Rockford Technical Training Institute (RTTI). Please read your

warranty and retain your receipt and original carton for possible future use.

Great product and competent installations are only a piece of the puzzle when it

comes to your system. Make sure that your installer is using 100% authentic instal-

lation accessories from Connecting Punch in your installation. Connecting Punch

has everything from RCA cables and speaker wire to Power line and battery con-

nectors. Insist on it! After all, your new system deserves nothing but the best.

To add the finishing touch to your new Rockford Fosgate image, order your Rockford

wearables, which include everything from T-shirts and jackets to hats and sunglasses.

To get a free brochure on Rockford Fosgate products and Rockford accessories, in

the U.S. call 480-967-3565 or FAX 480-967-8132. For all other countries, call +001-

480-967-3565 or FAX +001-480-967-8132.

PRACTICE SAFE SOUND™

CONTINUOUS EXPOSURE TO SOUND PRESSURE LEVELS OVER

100dB MAY CAUSE PERMANENT HEARING LOSS. HIGH POWERED

AUTOSOUND SYSTEMS MAY PRODUCE SOUND PRESSURE LEVELS

WELL OVER

130dB. USE COMMON SENSE AND PRACTICE SAFE

SOUND

If, after reading your manual, you still have questions regarding this product, we rec-

ommend that you see your Rockford Fosgate dealer. If you need further assistance,

you can call us direct at 1-800-669-9899. Be sure to have your serial number, model

number, and date of purchase available when you call.

The serial number can be found on the outside of the box. Please record it in the space

provided below as your permanent record. This will serve as verification of your facto-

ry warranty and may become useful in recovering your product if it is ever stolen.

Serial Number: __________________________________

Model Number:__________________________________

– ii –

Introduction ..............................................................................................1

Package Contents......................................................................................1

Installation Considerations........................................................................2

Mounting Location....................................................................................3

Installation ................................................................................................4

Troubleshooting ........................................................................................8

Specifications............................................................................................9

Warranty Information ..............................................................................11

International Information ........................................................................12

GETTING STARTED

Welcome to Rockford Fosgate! This manual is designed to provide information

for the owner, salesperson, and installer. For those of you who want quick

information on how to install this product, please turn to the

Installation

Section

of this manual or refer to the icons listed below. Other information can

be located by using the Table of Contents. We, at Rockford Fosgate, have

worked very hard to make sure all the information in this manual is current.

But, as we are constantly finding new ways to improve our product, this infor-

mation is subject to change without notice.

TABLE OF CONTENTS

Sections marked

TROUBLESHOOTING

include recommendations for

curing installation problems

Sections marked

INSTALLATION

include “slam dunk”

wiring connections

+ -

TROUBLE-

Visit our website for the latest information on all Rockford products.

– 1 –

(2) FNX2401 Tweeters — Includes 3/4"

[20mm] silk dome tweeter, flush mount

housing, surface mount housing, wedge

mount housing

(2) Tweeter Mounting Brackets

(4) #8-32 x .500 Screws

(8) #8 x .75 Phillips Screws

(2) .110 Female Fast-on Connectors

(2) .110 Male Fast-on Connectors

(2) FNX1404 4" Midrange Speakers

(2) 4" Speaker Grilles

(2) 4" Speaker Grille Rings

(2) FNX242x 2-Way Crossovers

(8) #8 x 1.25 Phillips Screws

(20') 18-Gauge Speaker Wire

(2) FNX2401 Tweeters — Includes 3/4"

[20mm] silk dome tweeter, flush mount

housing, surface mount housing, wedge

mount housing

(2) Tweeter Mounting Brackets

(4) #8-32 x .500 Screws

(8) #8 x .75 Phillips Screws

(2) .110 Female Fast-on Connectors

(2) .110 Male Fast-on Connectors

(2) FNX2406U 6" Midrange Speakers

(2) 6" Speaker Grilles

(2) 6" Speaker Grille Rings

(2) FNX242x 2-Way Crossovers

(8) #8 x 1.25 Phillips Screws

(20') 18-Gauge Speaker Wire

(2) FNX2401 Tweeters — Includes 3/4"

[20mm] silk dome tweeter, flush mount

housing, surface mount housing, wedge

mount housing

(2) Tweeter Mounting Brackets

(4) #8-32 x .500 Screws

(8) #8 x .75 Phillips Screws

(2) .110 Female Fast-on Connectors

(2) .110 Male Fast-on Connectors

(2) FNX2405 5-1⁄4" Midrange Speakers

(2) 5-1⁄4" Speaker Grilles

(2) 5-1⁄4" Speaker Grille Rings

(2) FNX242x 2-Way Crossovers

(8) #8 x 1.25 Phillips Screws

(20') 18-Gauge Speaker Wire

FNX2414 4" fanaticX Component System

FNX2614U 6" fanaticX Component System

FNX2514 5-1/4" fanaticX Component System

(2) FNX2401 Tweeters — Includes 3/4"

[20mm] silk dome tweeter, flush mount

housing, surface mount housing, wedge

mount housing

(2) Tweeter Mounting Brackets

(4) #8-32 x .500 Screws

(8) #8 x .75 Phillips Screws

(2) .110 Female Fast-on Connectors

(2) .110 Male Fast-on Connectors

(2) FNX2406 6-1⁄2" Midrange Speakers

(2) 6-1⁄2" Speaker Grilles

(2) 6-1⁄2" Speaker Grille Rings

(2) FNX242x 2-Way Crossovers

(8) #8 x 1.25 Phillips Screws

(20') 18-Gauge Speaker Wire

FNX2614 6-1/2" fanaticX Component System

This manual provides information on the features and installation of the

fanaticX Systems. We suggest you save this manual for future reference. We

strongly recommend you have your Authorized Rockford Fosgate Dealer

install the fanaticX System. If you do choose to install the system yourself,

please be sure to read the entire manual before beginning.

INTRODUCTION

PACKAGE CONTENTS

– 2 –

Tools Needed

The following is a list of some of the tools necessary for the installation of your

speakers.

• Power Drill with assorted bits • #2 Phillips Screwdriver

• Tape Measure • Voltmeter

General

1. For safety, disconnect the negative lead from the battery prior to beginning

the installation.

2. Never run wires underneath the vehicle. Running the wires inside the vehi-

cle provides the best protection.

3. Avoid running wires over or through sharp edges. Use rubber or plastic

grommets to protect any wires routed through metal.

4. Mount the speakers/crossovers away from electrical sources (other than the

amplifier) i.e., power cables, electronic fuel pumps, vehicle computers,

and other potential noise sources.

5. Mount the speakers/crossovers away from areas of extreme heat or mois-

ture.

Speakers

1. Make sure there is an area large enough of the speaker to mount. Warning!

Failure to do this can cause damage to the speaker if the speaker frame is

bent during installation.

2. Check to see that the location is deep enough for the speaker(s) and the

location does not interfere with the normal operation of the vehicle.

3. When mounting the speaker(s) in the door of a vehicle, make sure the

speaker(s) do not interfere with either the door or window operation.

4. When mounting the speaker(s) on the rear deck of the vehicle, check the

operation of the rear hatch or trunk lid. Make sure the torsion bars and

other moving parts are not obstructed by the speaker(s) installation.

• Please refer to the Specifications section of this manual for proper mount-

ing diameter and depth of the speaker(s).

Crossovers

1. Make sure there is a flat area large enough for the crossover to mount.

2. For best results, mount the crossover(s) next to the amplifier for a decora-

tive finish to the installation and provide an easy upgrade (no new wires to

run) for a bi-amp Rockford Fosgate system in the future.

INSTALLATION CONSIDERATIONS

+ -

– 3 –

• Sound radiated from a “point source” provides the best stereo imaging

because the separation of the acoustical centers between the midrange

and tweeter for each channel is at the optimum distance. In a closed en-

vironment such as an automobile, horizontal speaker alignment (Figure

2-A) can cause severe amplitude and phase differences which will

degrade not only the imaging, but also the frequency response. This is

due to the path length differences between the midrange and tweeter.

With a vertical alignment (Figure 2-B), the path length difference

A solid front stage with a good image is one of the most difficult tasks to

achieve in a vehicle. No car has the optimum listening environment. This

makes proper sound staging very difficult to accomplish. Most speakers

tend to be placed where they will fit easily, as opposed to where they can

perform the best. The mounting location of your speakers will have a great

effect on the sound quality of your stereo system. The special care taken to

place the speakers will yield many hours of listening enjoyment in return.

Several important recommendations should be followed.

• Place the speakers where they have a direct path to the listening area.

• For the best integration between the midrange and tweeter, the tweeter

should be placed less than 2" from the midrange (Figure 1).

• If you cannot place the tweeter less than 2"

from the midrange, then place the tweeter

more than 7" from the midrange. Placing the

tweeter 2"–7" from the midrange can cause

destructive interference (frequency response

problems) which will affect the speaker's abil-

ity to reproduce the frequency range around

the crossover frequency of the system.

• Whenever possible, place the tweeter direct-

ly above or below the midrange as this max-

imizes the imaging (point source) capability

of the speakers (Figure 2).

Figure 1

2" or less

Figure 2-A

Figure 2-B

MOUNTING LOCATION

– 4 –

between the midrange and tweeter are reduced to a minimum. The result

is a negligible difference in path lengths between the midrange and

tweeter regardless of the proximity of the listener to the speakers.

Mounting the speaker with minimum path length difference will ensure

the best staging and imaging possible from your audio system.

1. Cut the proper size hole for the midrange/woofer.

• For the 4” speaker, cut a 90mm (3

⁄

") diameter hole

• For the 5-1/4” speaker, cut a 114mm (4

⁄

") diameter hole

• For the 6” speaker, cut a 129mm (5

⁄

") diameter hole

• For the 6-1/2” speaker, cut a 139mm (5

⁄

") diameter hole

2. Place the mounting ring over the mounting hole and mark the location of

the screw mounting holes.

3. Remove the ring. Drill the holes for the screws using a 1/8" drill bit.

4. Route the wire through the hole.

5. Attach the wires and be sure to observe the proper speaker polarity.

6. Place the mounting ring over the speaker.

7. Place the speaker into the hole and screw the speaker into place.

Be care-

ful not to bend the speaker frame during this step.

8. Press the speaker grille into the mounting ring.

Mounting the Midrange

INSTALLATION

+ -

– 5 –

Flush Mount Tweeter

Tweeter

Surface Mount Tweeter

Trim

Ring

Back

Plate

Flush

Housing

Tweeter Trim

Ring

Back

Plate

Surface

Housing

Wedge Mount Tweeter

Tweeter Wedge

Housing

– 6 –

• Be sure to maintain speaker polarity

• 0dB Tweeter Level matches the amplitude of the tweeter to the midrange

• -3dB Tweeter Level reduces the amplitude of the tweeter -3dB lower than the

midrange. (ex. ideal for tweeters located high in door panels and midranges located

low in the kick panel)

•

Replaceable Tweeter Protection Bulb acts as a fuse to protect against overload. If the

bulb burns out, remove the burned out bulb and insert a new bulb (part# HDW10932)

into the retainer clips.

Crossover Connections Model 242X

– 7 –

The Fanatic Component Systems are opti-

mized for full range music reproduction. In

cases where a subwoofer is used, the

midrange can be bandpassed in order to pre-

vent overlapping frequencies from the

midrange into the subwoofer.

1. Determine the frequency range that the sub-

woofer will play (i.e.: 20Hz–80Hz)

2. Use the low-pass crossover frequency of

the subwoofer system (i.e.: 80Hz) as the

high-pass crossover frequency for the

midrange

3. Select the appropriate capacitor value (i.e.: 500µF) to properly bandpass

the midrange

4. Place the capacitor in series with the “+” terminal of the speaker

80Hz 500µF

100Hz 400µF

130Hz 300µF

200Hz 200µF

260Hz 150µF

400Hz 100µF

Frequency Speaker

(Hertz) (4 ohms)

Bandpassing the Midrange

– 8 –

Check wiring, and repair

or replace as needed

Distorted sound

from speakers

Tweeters “burn up”

easily

Engine noise from

one or more

speakers

Check for shorts in the

wiring with a volt/ohm

meter and repair or

replace wires as needed

Re-route speaker wiring

away from noise sources

(refer to the

Installation

Considerations

section of

this manual)

Move crossovers away

from noise sources (refer

to the

Installation

Considerations

section of

this manual)

Speaker wires shorted

to chassis of vehicle

Speaker wires are rout-

ed near radiated noise

source (power cables,

vehicle computers, etc.)

Crossover is mounted

near radiated noise

source (power cables,

vehicle computers, etc.)

Symptom Diagnosis Remedy

No sound from

speakers

Check wiring, and repair or

replace as needed

Check system with known

working amplifier and re-

pair or replace as needed

Check for shorts in the wir-

ing with a volt/ohm meter,

and repair or replace wires

as needed

Check system with known

working speaker and repair

or replace as needed

Wires between amplifier,

crossover or speakers not

connected properly

Amplifier has no output

Speaker wires are short-

ed to each other or to

the chassis of the vehicle

Speakers are blown

Excessive power from

amplifier

Equalizer in system (if

available) has exces-

sive boost in the high

frequency range

Check gain settings on ampli-

fier and readjust as necessary

Check settings on equalizer

and readjust as necessary

Incorrect wiring be-

tween crossover and

speakers

TROUBLESHOOTING

TROUB

– 9 –

* Power Ratings (PE) is established with

recommended filter network

System Model Number FNX2414 FNX2514 FNX2614U FNX2614

Midrange Model Number FNX2404 FNX2405 FNX2406U FNX2406

Nominal Diameter 4" 5

⁄

"6"6

⁄

Nominal Impedance 4Ω 4Ω 4Ω 4Ω

Frequency Response 50Hz–8kHz 40Hz–6kHz 40Hz–6kHz 35Hz–5kHz

Fs (Hz) 104Hz 87Hz 61Hz 72Hz

Qes .920 .732 .507 .902

Qms 4.360 4.083 3.330 4.226

Qts .735 .621 .440 .743

Vas (ft

/liter) .07/2.0 .13/3.9 .31/8.8 .72/20.3

Xmax (in/mm) .11/2.9 .15/3.7 .15/3.7 .15/3.7

Sensitivity 85.9dB 87.5dB 87.9dB 88.5dB

RMS Power Handling 70 Watts 70 Watts 70 Watts 70 Watts

Mounting Diameter 90.48mm 113.50mm 129mm 139.06mm

⁄

") (4

⁄

") (5

⁄

") (5

⁄

Mounting Depth 54mm (2

⁄

") 60mm (2

⁄

") 48mm (1

⁄

") 65mm (2

⁄

Model FNX2401

Nominal Diameter 3/4" (20mm)

Nominal Impedance 4Ω

Frequency Response 1.8kHz–20kHz

Fs 1.8kHz

Sensitivity 93dB

RMS Power Handling 70 Watts*

Mounting Diameter See drawings

Mounting Depth See drawings

Model FNX242x

Crossover Type 2-Way

Crossover Frequency 4kHz @ 4Ω

Crossover Slope 18dB/octave High-Pass

6dB/octave Low-Pass

Filter Q 0.707 (Butterworth)

Tweeter Protection Optical Compression

Tweeter Pad 0dB/-3dB

SPECIFICATIONS

– 10 –

(Specifications are subject to change without notice)

1.562"

Wedge

Mount

Surface

Mount

Flush

Mount

.675" .965"

.25"

1.0"

.375"

1.0"

1.795"

1.74"

1.94"

1.24"

1.36"

3.32"

4.85"

– 11 –

Rockford Corporation offers a limited warranty on Rockford Fosgate products on the

following terms:

• Length of Warranty

1 year on speakers 30 days on speaker B-stock (receipt required)

3 years on electronics 90 days on electronic B-stock (receipt required)

2 years on source units

• What is Covered

This warranty applies only to Rockford Fosgate products sold to consumers by

Authorized Rockford Fosgate Dealers in the United States of America (U.S.) or its

possessions. Product purchased by consumers from an Authorized Rockford

Fosgate Dealer in another country are covered only by that country’s Distributor

and not by Rockford Corporation.

• Who is Covered

This warranty covers only the original purchaser of Rockford product purchased

from an Authorized Rockford Fosgate Dealer in the U.S. In order to receive ser-

vice, the purchaser must provide Rockford with a copy of the receipt stating the

customer name, dealer name, product purchased and date of purchase.

• Products found to be defective during the warranty period will be repaired or

replaced (with a product deemed to be equivalent) at Rockford's discretion.

• What is Not Covered

1. Damage caused by accident, abuse, improper operations, water, theft

2. Any cost or expense related to the removal or reinstallation of product

3. Service performed by anyone other than Rockford or an Authorized Rockford

Fosgate Service Center

4. Any product which has had the serial number defaced, altered, or removed

5. Subsequent damage to other components

6. Any product purchased outside the U.S.

7. Any product not purchased from an Authorized Rockford Fosgate Dealer

• Limit on Implied Warranties

Any implied warranties including warranties of fitness for use and merchantabil-

ity are limited in duration to the period of the express warranty set forth above.

Some states do not allow limitations on the length of an implied warranty, so this

limitation may not apply. No person is authorized to assume for Rockford Fosgate

any other liability in connection with the sale of the product.

• How to Obtain Service

Please call 1-800-669-9899 for Rockford Customer Service. You must obtain an

RA# (Return Authorization number) to return any product to Rockford Fosgate.

You are responsible for shipment of product to Rockford. Always include Proof of

Purchase. Mark RA# on outside of shipping carton.

Ship to:

Electronics

Rockford Corporation

Warranty Repair Department

2055 E. 5th Street

Tempe, AZ 85281

RA#:_________________

Ship to:

Speakers

Rockford Acoustic Design

(Receiving-speakers)

609 Myrtle N.W.

Grand Rapids, MI 49504

RA#:_________________

LIMITED WARRANTY INFORMATION

MONTAJE

LEA DETENIDAMENTE LAS SIGUIENTES INSTRUCCIONES DE INSTA-

LACIÓN DEL PRODUCTO.

Este manual contiene información sobre la

construcción, installación y funcionamiento

de los sistemas Fanatic X. Le recomendamos

que conserve el manual para futuras consul-

tas.

Es preferible que la instalación de sistema

Fanatic X sea realizada por un distribuidor

autorizado Rockford Fosgate. Si prefiere

realizar la instalación usted mismo, asegurese

de leer el manual en su totalidad antes de

comenzar.

• Le mejor interacción entre tweeter y medio se consigue si no están sep-

arados entre si más de 5 cenimetros. (Figura 1)

– 12 –

1. Corte el agujero para el medio/woofer.

• Par el 102mm, corte un circulo de 90mm de diámetro

• Par el 133mm, corte un circulo de 114mm de diámetro

• Par el 152mm, corte un circulo de 129mm de diámetro

• Par el 165mm, corte un circulo de 139mm de diámetro

2. Use los anillos de montaje de plástico como plantilla. Marque la posi-

ción de los tornills de anclaje.

3. Quite el anillo y perfore los agujeros con una broca de 3mm.

+ -

INSTALACIÓN

Montaje del altavoz de medios

no superior a 5cm

Figura 1

INTRODUCCIÓN — ESPAÑOL

– 13 –

4. Pase el cable de altavoz a través del agujero.

5. Conecte los cables observando la polaridad. Mantenga los cables aleja-

dos pe partes móviles o cortantes.

6. Monte el anillo de montaje sobre el medio/woofer.

7. Asegure el altavoz en la abertura con los tornillos. Tenga la precaución

de no doblar el marco del altavoz en este proceso.

8. Presione la rejilla en el anillo de montaje.

• Asegúrese de mantener la polaridad de los parlantes

• Nivel de 0dB del Agudo cuadra con la amplitud del Agudo al Mediorango

• Nivel de -3dB del Agudo reduce la amplitud del Agudo -3dB más bajo que el mediorango. (Ej.

Ideal para agudos colocados en paneles de puerta elevados y mediorangos localizados en pan-

eles bajos – kick panel)

• Bombilla recambiable de protección del altavoz de alta frecuencia La bombilla de luz actúa

como un fusible para proteger contra sobrecargas. Si la bombilla se quema, saque la bombilla

quemada e inserte una bombilla nueva (pieza Nº HDW10932) en las grapas de sujeción.

– 14 –

VEUILLEZ LIRE LES INSTRUCITONS SUIVANTES POUR L'INSTALLATION

DE CES PRODUITS.

Ce manuel contient des informations sur les caractéristiques et l'installation

des systèmes Fanatic X. Nous vous proposons de garder ce manuel pour

toute référence future.

Nous vous recommandons vivement de faire installaer votre système punch

Fanatic X par un dealer agréé Rockford Fosgate. Si vous choisissez d'in-

staller le système vous même, assurez-vous de lire ce manuel entièrement

avant de commencer.

• Pour bénéficier d'une harmonie maxi-

mum entre le médium et l'aigu l'éloigne-

ment entre ces deux haut-parleurs devrait

être de moins de 5 cm entre les 2 chassis.

(Figure 1)

1. Découper un trou adapté au haut-parleur médium/woofer.

• Pour le 102mm, le diamètre du trou est de 90mm

• Pour le 133mm, le diamètre du trou est de 114mm

• Pour le 152mm, le diamètre du trou est de 129mm

• Pour le 165mm, le diamètre du trou est de 139mm

2. Placer l'anneau de montage sur le trou et repérer l'emplacement des

INTRODUCTION — FRANÇAIS

moins de 5cm

Figure 1

EMPLACEMENT DE MONTAGE

Montage du haut-parleur médium

INSTALLATION

+ -

– 15 –

trous des vis.

3. Retirer l'anneau. Percer les trous des vis en utilisant une mèche de 3mm.

4. Faire passer les fils dans le médium/woofer.

5. Connecter les fils au haut-parleur en respectant les polarités. Eloigner les

fils de toute partie tranchante ou mobile du véhicule.

6. Placer l'anneau de montage au-dessus du trou central.

7. Placer le haut-parleur au-dussus du trou central. Visser le haut-parleur

dans son emplacement. Faire attention à ne pas tordre le chassis du

haut-parleur durant cette étape de montage.

8. Mettre la grille dans l'anneau de montage.

• Vérifier les polaritées des haut-parleurs

• 0dB Pas d'atténuation de l'aigu par rapport au médium.

• -3dB d'atténuation du niveau de l'aigu

-3dB d'atténuation par rapport au médium. (Ex: Idéal pour le positionnement de l'aigu en haut

de portière et le mèdium en bas ou “kick panel” Volume de charge créer en bas de porte ou

dans l'angle de celle-ci, au niveau des pieds.)

• Ampoule de protection remplaçable pour tweeter Cette ampoule sert de fusible de protec-

tion contre les surcharges. Si lampoule brûle, retirez-la et placez-en une neuve (réf.

#HDW10932) dans les clips de retenue.

– 16 –

DIE FOLGENDE BEDIENUNGSANLEITUNG SOLL IHNEN BEIM EINBAU

EINE HILFESTELLUNG GEBEN.

Diese Bedienungsanleitung enthält Informationen für den Gebrauch und

Einbau des Fanatic X Systems. Wir empfehlen, diese auch für Fragen in der

Zukunft sorgfältig aufzubewahren.

Es ist empfehlenswert, sich das Fanatic X System von einem Autorisierten

Rockford Fosgate Fachhändler einbauen zu lassen. Sollten Sie den Einbau

jedoch selber vornehmen wollen, so empfehlen wir Ihnen, die

Bedienungsanleitung sorgfälitg zu lesen.

• Für das optimale Zusammenspiel von

Mittel- und Hochtöner, sollte der

Hochtöner niemals weiter als 5cm vorn

Mitteltöner entfernt montiert werden.

(Abb. 1)

1. Schneiden Sie die richtige Lochgröbe für den Mitteltöner oder Midbab aus.

• Für den 102mm, schneiden Sie ein 90mm Ø Loch

• Für den 133mm, schneiden Sie ein 114mm Ø Loch

• Für den 152mm, schneiden Sie ein 129mm Ø Loch

• Für den 165mm, schneiden Sie ein 139mm Ø Loch

2. Setzen Sie den Montagering auf das Loch und markieren Sie die Löcher

für die Schrauben.

+ -

Abstand max. 5cm

(Abb. 1)

ENLEITUNG — DEUTSCH

EINBAUORT

EINBAU

Montage des Mitteltöners

– 17 –

3. Nehmen Sie den Ring wieder ab und bohren Sie dann, mit einem

passenden Bohrer, die Schraubenlöcher vor.

4. Führen Sie das Kabel durch das Loch.

5. Schlieben Sie die Lautsprecherkabel an. Kontrollieren Sie, ob die

Polarität stimmt. Stellen Sie sicher, dab das Lautsprecherkabel an keinen

scharfen oder sich bewegenden Teilen anliegt.

6. Plazieren sie den Montagering über dem mitteltöners.

7. Plazieren Sie den Lautsprecher im Loch und befestigen Sie diesen. Seien

Sie dabei sehr vorsichtig, so dab sich der Lautsprecherkorb nicht verzieht.

8. Drücken Sie das Lautsprechergitter im Montagering fest.

• Achten Sie auf die Lautsprecherpolarität

• 0dB Hochtonabsenkung stimmt mit der Lautstärke med mitteltöners überein

• -3dB Hochtonabsenkung, reduziert die Lautstärke des Hochtöners gegenüber der Lautstärke des

Mitteltöners -3dB leiser, als der Mitteltöner (Ideal für Einbauten, bei denen die Hochtöner im

Armaturenbrett und die Mitteltöner in Fubraum eingesetzt werden)

•

Austauschbare Birne zum Schutz des Hochtöners Die Glühbirne dient als Sicherung, um vor

Überladung zu schützen. Sollte die Birne ausbrennen, die ausgebrannte Birne entfernen und eine

neue Birne (Ersatzteilnr. HDW10932) in den Halterungsclip einführen.

La page charge ...

Rockford Fosgate Fanatic X FNX2614 Installation & Operation Manual

Marque: Rockford Fosgate

Modèle: Fanatic X FNX2614

Catégorie: Haut-parleurs de voiture

Taper: Installation & Operation Manual

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Rockford Fosgate Fanatic X FNX2614

Documents connexes

Autres documents

Audio Design T252-S Le manuel du propriétaire