brondell Pro Filter Replacement Pack Le manuel du propriétaire

Catégorie
Purificateurs d'air
Taper
Le manuel du propriétaire

Ce manuel convient également à

Owner's Manual
PRO SANITIZING
AIR PURIFIER
WITH AG+ TECHNOLOGY
BY AURABEAT
MODELS P700BB/P7004C/APP60/CANP700BB
2
Read this Owner’s Manual for correct
installation, use, and maintenance of this
product. After reading and completing
installation, keep this manual in a place that
is easily accessible.
SAFETY INFORMATION
3 Important Safeguards
PRODUCT FEATURES
6 Main Features
7 Control Panel Detail
8 Five-Stage Purification
OPERATION
9 Preparing for First Use
10 Product Operation
MAINTENANCE
12 Filter Life and Cleaning Schedule
13 Cleaning the Air Sensor
14 Replacing the Filters
TECHNICAL INFORMATION
15 Troubleshooting
17 Product Specifications
18 Warranty
19 Contact Information
TRANSLATIONS
20 Spanish
38 French
BRONDELL PRO SANITIZING AIR PURIFIER WITH
AG+ TECHNOLOGY BY AURABEAT OWNER’S MANUAL
Contents
3
DANGER: If not observed, serious injury or even death may occur as a result.
Do not use a damaged power plug or plug
into a loose electric outlet.
Please connect the power plug to a
grounded electrical outlet rated for 120 V ~
60 Hz.
Do not move the product by pulling on the
power cord.
Do not handle the product or power plug
with wet hands.
Do not forcefully bend the power cord or
place heavy objects on it to prevent it from
being damaged or deformed.
Do not connect and pull out the power plug
or cord repeatedly.
If the electric outlet is wet, carefully unplug
the product and let the electric outlet dry
completely before subsequent use.
Unplug the product before cleaning,
repairing, inspecting, or replacing parts.
Remove any dust or water from the power
plug prior to plugging in.
Do not plug the product into an electrical
outlet or power strip that is being used by
too many other products. Use an electrical
outlet adequate for the wattage of the
product.
Unplug the product if it is not going to be
used for a long time.
If the power cord is damaged – do not
operate the product and do not attempt to
repair, modify, or replace the cord yourself.
Contact the Brondell Service Center toll
free at 888-542-3355 or email us through our
website.
Do not insert any wires or sharp objects into
any product gaps. This may result in electric
shock, fire, or product damage.
If the product produces a strange noise,
a burning smell, or emits smoke, unplug it
immediately from the electrical outlet and
contact Brondell. Failure to do so may result
in electric shock or fire.
Do not place an electronic or gas heater
near the product or place near heating
vent. This may result in fire or product
deformation. Do not place any containers
filled with water or other liquids, food,
metallic objects, or any flammable material
on top of the product. If foreign material
enters the product, this may result in
electric shock or fire.
Do not use the product in locations exposed
to excessive moisture or rain and do not
splash water onto the product. Never place
the product in or near water.
Do not use the product in areas where
flammable gases or combustible materials
are used or stored.
Do not spray any flammable materials such
as insecticides or air fragrances near or into
the air inlet.
Do not disassemble, repair, or modify the
product yourself. If repair is needed please
contact the Brondell Service Center toll
free at 888-542-3355 or email us through our
website.
Clean the exterior with a damp cloth. Do not
clean the product using benzene, thinner, or
abrasives.
Do not use the product in a factory or
industrial setting where machine oil may be
present in the air.
SAFETY INFORMATION
Important Safeguards
READ ALL INSTRUCTIONS BEFORE USING
BE CAREFUL TO KEEP THIS SAFETY INFORMATION. PLEASE READ THIS INFORMATION
TO PREVENT PROPERTY LOSS AND ENSURE SAFETY.
4
WARNING: To reduce the risk of fire, electric shock or injury, read
and understand this user guide before operating this product.
Do not insert fingers or foreign objects into
the air inlet or air outlet.
Do not let children play with the product or
climb on it. Children should be supervised
to ensure that they do not play with the
product.
When removing the front cover, exercise
caution that no clothing or body parts
become stuck in the top vent of the product.
This product can be used by children, age
8 years and up, and persons with reduced
physical or mental capabilities if they have
been given supervision or instruction
concerning use of the product in a safe way
and understand the hazards involved.
Cleaning and user maintenance shall not be
performed by children without supervision.
Do not run cord under carpeting. Do not
cover cord with throw rugs, runners, or
similar coverings. Do not route cord under
furniture or appliances. Arrange cord away
from trac area and where it will not be
tripped over.
Lack of proper cleaning and maintenance
may result in fire, electric shock, or injury.
Unplug or disconnect the product from the
power supply before servicing.
This product has a polarized plug (one
blade is wider than the other). To reduce
the risk of electric shock, this plug is
intended to fit in a polarized outlet only
one way. If the plug does not fit fully in the
outlet, reverse the plug. If it still does not
fit, contact a qualified electrician. Do not
attempt to defeat this safety feature.
SAFETY INFORMATION
Important Safeguards
READ ALL INSTRUCTIONS BEFORE USING
BE CAREFUL TO KEEP THIS SAFETY INFORMATION. PLEASE READ THIS INFORMATION
TO PREVENT PROPERTY LOSS AND ENSURE SAFETY.
5
CAUTION: If not observed, minor physical injury
or property damage may occur as a result.
Do not install the product on a sloped or
uneven surface.
Do not apply force or impact to the product.
Install the product so that no obstacles
block the circulation of air around the
product.
Install the product away from strong
artificial lighting or direct sunlight. Do not
install the product in a location exposed to
direct sunlight.
Replace the filters according to the filter
replacement cycle.
SAFETY INFORMATION
Important Safeguards
READ ALL INSTRUCTIONS BEFORE USING
BE CAREFUL TO KEEP THIS SAFETY INFORMATION. PLEASE READ THIS INFORMATION
TO PREVENT PROPERTY LOSS AND ENSURE SAFETY.
6
PRODUCT FEATURES
Main Features
Control Panel
Allows user to
control all functions
of the air purifier
Power Cord Port
Port to insert the
power cord
Air Outlet
Clean, filtered air
is expelled from
the unit
Air Quality Indicator
Color spectrum
indicates the air quality
Front Panel
Remove this to
change the filters
Air Intake Grille
Air in the room is taken
into the unit through
the vent holes in the
front panel
Handle
Allows the user to
carry the air purifier
from room to room
as needed
Air Quality Sensor
Measures the air
quality
7
Timer
Touch to activate the Timer.
User can set the unit to stay
on for 1 to 12 hours.
PRODUCT FEATURES
Control Panel Detail
Power Button
Touch to turn
power on/o.
Sleep Mode
Touch to engage
Sleep Mode.
UV
Touch to turn
UV on/o.
Digital Display
Displays PM2.5 level,
timer hours, fan speed,
filter usage.
Filter Check Indicator
The red filter check icon
will appear when it is
time to check the health
of the filters.
Child Lock
Touch to lock/
unlock all control
panel buttons.
Plasma
Touch to turn the
Plasma function
on/o.
Air Speed Selector
The unit powers on in Auto Mode
(P0). Touch to select between
three air speed modes: LOW
(P1), MEDIUM (P2), HIGH (P3). To
reselect Auto Mode, touch the
button a fourth time.
8
PRODUCT FEATURES
Five-Stage Air Purification
STAGES 13: FILTER PURIFICATION
1. Pre-Filter
Prevents large particles such as dander,
hair and lint from passing through the
system.
2. High Eciency AG+ Air Filter
This HEPA Grade eectively filters small
particles such as dust, smoke, pollen and
mold, allergens and harmful PM2.5 as small
as 0.01 microns, which includes viruses and
bacteria.
3. Nanocrystalline Air Filter
Natural nanocrystalline minerals absorb
harmful gases, formaldehyde, benzene,
ammonia, VOCs and other odor-rich
pollutants between 0.4 – 0.62 nanometers.
STAGE 4: UV DISINFECTION
UV lamp helps to sanitize the air and
the insides of the unit.
STAGE 5: PLASMA SANITIZATION
Generates positive and negative
ions that, when released into the air,
change the air’s energy, eectively
destroying microorganisms.
1
2
3
9
1. Remove the front panel by pulling it away
from the base unit.
2. Remove all the plastic packaging from
the filters.
3. Put the filters back in the unit in the
following order:
a) Nanocrystalline Filter
b) High Eciency AG+ Air Filter
Note: Make sure the cloth tabs on both filters
that indicate “Front” are facing outward.
4. Re-attach the front panel by inserting the
tabs on the bottom of the front panel into
the slots at the bottom base of the unit.
Push the top of the panel towards the unit;
a magnetic closure ensures the front panel
clicks securely into place.
Note: If the unit is plugged in, it will chime and
the Power button will begin blinking red when
the front panel is secured into place.
OPERATION
Preparing for First Use
Be sure to remove all plastic packaging from the filters before use.
Step 1
Step 4
Step 3
ab
10
Turning the Brondell Pro Sanitizing Air
Purifier On
1. Insert the power cord into the power cord
port on the back of the unit and plug the
unit into the nearest power outlet.
2. Touch the red blinking Power
button on the top of the control
panel to turn the unit on. The unit
will chime and the control panel
will illuminate.
The unit will start in Auto Mode and begin to
sense the air quality in the room. Once the
air quality has been determined, the PM2.5
value will display on the control panel and
the unit will regulate to an appropriate fan
speed.
The airow is adjusted according to PM2.5.
Auto Mode is set as follows:
3. To turn the Brondell Pro Sanitizing Air
Purifier o, press the Power button.
The unit will chime and power o.
Selecting the Operating Mode
Air Speed – Touch the Speed
button to toggle between 3 fan
speeds: P1 (LOW), P2 (MEDIUM),
and P3 (HIGH). Touch the Speed
button a fourth time for Auto
Mode (P0).
Sleep Mode – Touch the Sleep
button to enter Sleep Mode.
Fan speed will power down to
the lowest level, the air quality
indicator light will turn o, and all
lights on the control panel will turn o
except for the Sleep button. Touch the
Sleep button again to disengage
Sleep Mode.
UV – Touch the UV button to
activate UV sanitization. The UV
light inside the machine will turn
on. To turn o UV sanitization,
touch the UV icon.
Plasma – Touch the Plasma
button to initiate the unique
Plasma generation. The unit will
emit positive and negative ions
into the air, creating enough
energy to disturb bonds and destroy
microorganisms. These negative ions will
remove smoke, dust, and odors from the air
while improving air quality and health.
OPERATION
Product Operation
Place the air purifier on a flat, solid surface. Do not block the Air Outlet with
objects, and remove any heat sources and/or open flames near the unit.
PM2.5
Value
Air
Quality
Level
Air
Quality
Light
Color
Airow
Level
10-79 Good Green 1
80-199 Fair Blue 2
200-500 Bad Red 3
11
OPERATION
Product Operation (Cont’d)
Place the air purifier on a flat, solid surface. Do not block the Air Outlet with
objects, and remove any heat sources and/or open flames near the unit.
Setting the Timer
1. Touch the clock icon to initiate
a timer duration between 1 and
12 hours.
2. Continue to touch the clock icon
until you reach the timer duration desired.
3. To disengage the Timer before the end of
the set duration, touch the clock icon until
the Control Panel displays 0.
Setting the Child Lock
1. Touch the lock icon to engage
the Child Lock. When Child Lock
is on, all other buttons will chime
twice when touched and will not
respond to touch commands.
2. Touch and hold the lock icon for 3 seconds
to disengage the Child Lock.
Note: Icon names will only be displayed when
its function is activated. In Sleep mode, only
Sleep will be displayed even if other functions
are activated.
12
MAINTENANCE
Filter Life and Cleaning Schedule
To check the number of hours your filter set has been in use at any time, touch and hold the lock
icon for 3 seconds while Child Lock is not in use. The Air Quality Sensor display will show the
amount of hours the current filter set has been active.
The Filter Check Indicator light on the Brondell Pro Sanitizing Air Purifier is programmed to
illuminate every 2000 hours the unit is in use, however, filters lasts 8-12 months and should be
replaced at least once annually. If the filters are cleaned properly and on schedule, the Filter
Check Indicator light could go on 3 or more times before you actually have to replace filters.
Regular cleaning when air quality is extremely poor is needed.
Proper care and maintenance of the Brondell Pro Sanitizing Air Purifier is critical to performance.
The following chart shows recommended cleaning intervals for each part of the unit.
Part Time Method
External body As needed Wipe with clean damp cloth.
Air Intake Every two months Clean with soft brush or cloth.
Air Outlet Every two months Clean with soft brush or cloth.
Air Sensor Every two months First, wipe with a damp cotton swab.
Then wipe dry with a dry cotton swab.
Woven Pre-Filter Every two to
four weeks
Vacuum or rinse thoroughly in warm water.
Do not use heat to dry the woven pre-filter.
Nanocrystalline
Filter Every two months Expose to sunlight for one to three hours.
High Eciency
AG+ Filter Every two months
Check the filter color. If the filter is light
grey, you can reuse another 2000 hours.
If the filter is dark or black, it is time to
replace it.
UV Light Bulbs Every twelve months Check the UV bulbs to ensure they are
functioning. Follow instructions on page 14.
Filter life may vary according to usage and environment.
Filters sealed in original packaging, unopened, have a shelf life of 5 years.
Replacement filters are available for purchase at brondell.com.
Cleaning the unit while it is plugged in may result in electric shock, electric spark
and serious injury. Unplug the unit before cleaning or performing maintenance.
13
1. Remove the Air Sensor Cover by pinching
the tab towards the cover to release it.
2. Clean the Air Inlets (a) and Outlet Vents (b)
with a small brush or cotton swab.
3. Wet a cotton swab lightly and clean the
Lens (a), Dust Inlet (b), and Dust Outlet (c).
After cleaning, use a dry cotton swab to
remove any moisture.
4. Re-attach the Air Sensor Cover.
Note: Without regular cleaning of the Air
Sensor, the Brondell Pro Sanitizing Air Purifier
will decline in performance.
MAINTENANCE
Cleaning the Air Sensor
Step 1
Step 2
Step 3
b
a
c
a
b
14
1. Ensure the Brondell Pro Sanitizing Air Purifier is
powered o.
2. Remove the front panel by grasping the
top sides of the panel and pulling it away from the unit.
3. Remove the existing filters.
4. Remove all plastic packaging from the replacement
filters. With the front tabs facing out, install filters in
the following order:
a) Insert the Nanocrystalline filter by
laying its bottom edges flush against
the filter cabinet then pushing the filter firmly in
place.
b) Insert the High Eciency AG+ Air Filter, with the
front tabs and the woven pre-filter facing out in the
same manner.
5. Re-attach the front panel by inserting the tabs on the
bottom of the front panel into the slots at the bottom
base of the unit. Push the top of the panel towards the
unit. A magnetic closure ensures the front panel clicks
securely into place.
6. Touch and hold the clock icon for 3 seconds to reset
the Filter Check Indicator light.
Check the Status of the UV Light Bulbs
While replacing the filters, you may check to ensure all of
the UV Light Bulbs are functioning.
After removing the existing filters (step 3), re-attach
the front panel and power the unit on. At the bottom of
the front panel the blue UV light from 5 UV bulbs will
emanate through the grille. If all bulbs are functioning,
power the unit o and continue to step 4 of the filter
replacement process.
If a bulb is out, please call the Service Center at
888-542-3355 or email us at support@brondell.com.
MAINTENANCE
Replacing the Filters
Be sure to remove all plastic packaging from the filters before use.
Step 5
Step 6
Step 2
Step 4
WARNING:
UV light is harmful to your eyes. Always place
the front panel on the unit before checking the
UV light bulbs and do not look directly at the bulbs
for an extended period of time.
ab
15
If the Brondell Pro Sanitizing Air Purifier appears to be operating abnormally, please
review the troubleshooting tips before calling the Brondell Service Center as most issues
are easily resolved with a few simple steps. If you are unable to resolve the issue after
checking the following items, please call the Service Center at 888-542-3355, Mon-Fri,
9am-5pm PST (English and Spanish spoken), or email us at support@brondell.com.
TECHNICAL INFORMATION
Troubleshooting
Problem Possible Cause(s) Solution(s)
Unit will not
power on
or
The Control
Panel does not
display any
icons
1. The front panel is not
installed correctly.
2. Power cord is not inserted
correctly into the unit’s
cable port.
3. Power cord is not properly
inserted into the electrical
outlet.
4. Power cord or plug is
damaged.
1. Remove the front panel and
attach it to the unit again.
2. Ensure that the power cord is
properly inserted into the cable
port on the back of the unit.
3. Unplug the unit and plug it
back into the electrical outlet.
4. Contact Brondell Customer
Service.
Fan is not
working
1. Unit is not switched on.
2. Motor requires servicing.
1. Ensure that the power cord is
properly inserted into the cable
port and properly plugged into
the outlet. Touch the Power
button.
2. Contact Brondell Customer
Service.
Fan does not
automatically
adjust when the
unit is in Auto
Mode
1. Auto Mode is not selected.
2. Air Sensor is dirty.
3. Air Sensor is broken or
malfunctioning.
1. Touch the Speed button until
the display shows “P0”.
2. Follow the steps on page 13
to clean the Air Sensor.
3. Contact Brondell Customer
Service.
When in Auto
Mode, the
Air Sensor or
PM2.5 indicator
is always red or
high
1. The unit may be impacted by
moisture, oil residue, smoke,
fumes, or aerosolized spray.
2. The Air Sensor is dirty.
3. Power cord is not properly
inserted into the electrical
outlet.
4. Power cord or plug is
damaged.
1. Move the unit to another
location.
2. Follow the steps on page 13
to clean the Air Sensor.
3. Unplug the unit and plug it
back into the electrical outlet.
4. Contact Brondell Customer
Service.
16
TECHNICAL INFORMATION
Troubleshooting (Contd)
Problem Possible Cause(s) Solution(s)
Poor
performance,
or not purifying
at optimum
capacity
or
Unit is running
unusually loud
1. Pre-filter needs cleaning.
2. One or more filters is due for
replacement.
3. Plastic packaging on filters
was not removed.
4. Clearance around the
purifier is not adequate for
air ventilation.
5. Missing filters or the filters
were installed in the wrong
order.
6. Recommended room size
has been exceeded.
7. Blockage at Air Inlet or Air
Outlet.
1. Vacuum the pre-filter. Review
the cleaning schedule for all
filters on page 12.
2. Replace the filters.
3. Remove the plastic packaging
and put the filters back in.
4. Ensure that there is clearance
of 20 inches on each side and
4 inches behind in the front of
the unit.
5. Ensure the filters are installed
in the correct order and facing
the proper direction. See step
4 on page 14 of this manual.
6. Coverage area is 413 sq ft at 4
air changes per hour and 827
sq ft at 2 air changes per hour.
Move the unit to a smaller room
or purchase an additional unit to
cover a larger area.
7. Contact Brondell Customer
Service.
Unpleasant
odor cannot be
eliminated
1. Filters need cleaning.
2. Filters need replacement.
1. The Nanocrystalline filter
can be reused after exposure
to sunlight. Review the
cleaning process for all filters
on page 12.
2. Replace the filters.
A red
rectangular
icon has
appeared on
the control
panel near
the PM2.5 air
quality display
1. The small red rectangular
icon is the Filter Check
Indicator light.
1. Power o the machine and
check the health of the filters.
Refer to the maintenance
schedule on page 12. To reset
the Filter Check Indicator, turn
the machine on and touch
and hold the Clock icon for 3
seconds.
If the Brondell Pro Sanitizing Air Purifier appears to be operating abnormally, please
review the troubleshooting tips before calling the Brondell Service Center as most issues
are easily resolved with a few simple steps. If you are unable to resolve the issue after
checking the following items, please call the Service Center at 888-542-3355, Mon-Fri,
9am-5pm PST (English and Spanish spoken), or email us at support@brondell.com.
17
TECHNICAL INFORMATION
Product Specifications
Types Specifications
Product Name Brondell Pro Sanitizing Air Purifier
with AG+ Technology by Aurabeat
Model P700BB/P7004C/APP60
Voltage 120 V
Frequency 60 Hz
Power 95W
Filtration Grade H12
Room Coverage
1655 sq ft at 1 air exchange per hour
827 sq ft at 2 air exchanges per hour
538 sq ft at 3 air exchanges per hour
413 sq ft at 4 air exchanges per hour
Casing Material High Quality ABS
Airflow 247.2 ft3/min (CFM)
Dimensions 24.7 in x 15.4 in x 8.3 in
Weight 19.2 lbs.
Sensor Type PM2.5 Sensor
Max. Noise ≤62 dB
EPA Establishment Number: 98565-CHN-1
18
Brondell products are backed by some of the most comprehensive warranties in the industry. Brondell
warrants that the Brondell Pro Sanitizing Air Purifier with AG+ Technology by Aurabeat shall be free from
defects in material and workmanship under normal use and service.
Residential & Commercial Warranty for Brondell Pro Sanitizing Air Purifier with AG+ Technology by Aurabeat
– 3-year limited warranty.
Includes Base Model numbers: P700BB, P7004C, and APP60
100% Coverage of defects or malfunctions of all electronic parts and labor for the entire product excluding
consumable filters for the first three years from original date of purchase.
Exclusions and Limitations
1. BRONDELL warrants its products to be free from manufacturing defects under normal use and service. This
warranty is extended only to the ORIGINAL PURCHASER.
2. BRONDELL’s obligations under this warranty are limited to repairs or replacement, at BRONDELL’s option,
of products or parts found to be defective, provided that such products were properly installed and used in
accordance with instructions. BRONDELL reserves the right to make such inspections as may be necessary
in order to determine the cause of the defect. BRONDELL will not charge for labor or parts in connection
with warranty repairs for the first three years from the date of purchase on all products except those that
may be subject to heavy commercial use limitations.
3. BRONDELL is not responsible for the cost of removal, return (shipping) and/or reinstallation of products.
This warranty does NOT apply to:
• Damage or loss which occurs during shipment.
• Damage or loss sustained through any natural or man-made causes beyond the control of BRONDELL,
including but not limited to fire, earthquake, floods, etc.
• Damage or loss resulting from negligent or improper installation including installation of a unit in a harsh or
excessively hazardous environment.
• Damage or loss resulting from removal, improper repair, modification of the product, or improper
maintenance including damage caused by improper cleaning and exchanging of filters
• Damage or loss resulting from acts which are not the fault of BRONDELL or which the Product is not
specified to tolerate.
• Normal wear and tear usage on the appliance or damages and wear to the filter during use or maintenance.
4. This warranty gives you specific legal rights. You may have other rights which vary from state to state.
THIS WRITTEN WARRANTY IS THE ONLY WARRANTY MADE BY BRONDELL. REPAIR OR REPLACEMENT AS
PROVIDED UNDER THIS WARRANTY SHALL BE THE EXCLUSIVE REMEDY AVAILABLE TO THE PURCHASER.
BRONDELL SHALL NOT BE RESPONSIBLE FOR LOSS OF USE OF THE PRODUCT OR FOR OTHER
INCIDENTAL, SPECIAL, OR CONSEQUENTIAL DAMAGES OR EXPENSES INCURRED BY THE PURCHASER OR
FOR LABOR OR OTHER COSTS DUE TO INSTALLATION OR REMOVAL OR COSTS OF REPAIRS BY OTHERS,
OR FOR ANY OTHER EXPENSE NOT SPECIFICALLY STATED ABOVE. EXCEPT TO THE EXTENT PROHIBITED
BY APPLICABLE LAW, ANY IMPLIED WARRANTIES, INCLUDING THAT OF MERCHANTABILITY, ARE
EXPRESSLY LIMITED TO THE DURATION OF THIS WARRANTY. SOME STATES DO NOT ALLOW LIMITATIONS,
SO THE ABOVE LIMITATION AND EXCLUSION MAY NOT APPLY TO YOU.
How to Obtain Service
To obtain repair service under this warranty, you must contact an authorized Brondell Service Center to obtain
an RMA (Return Merchandise Authorization) number. Proof of purchase in the form of a copy of the original
receipt must accompany the returned unit for the warranty to be valid. Take or ship the unit pre-paid to the
closest Brondell authorized service center along with the RMA number and proof of purchase. To obtain an
RMA number, contact the Brondell Service Center at 1-888-542-3355 or by email support@brondell.com.
TECHNICAL INFORMATION
Warranty
19
Brondell, Inc.
PO Box 470085
San Francisco, CA
94147-0085
support@brondell.com
www.brondell.com
For questions, contact:
Brondell Customer Service: 1-888-542-3355
Monday – Friday, 9am – 5pm PST
Manufactured by
Brondell, Inc.
PO Box 470085
San Francisco, CA
94147-0085
Research and Development
in Hong Kong
Made in China
Please retain receipt records
for any warranty claims.
Replacement Filter:
PP-41 Pro AG+ Replacement Filter Pack
20
Lea este manual del propietario para conocer
la instalación, el uso y el mantenimiento
apropiados para este producto. Después de
leer y completar la instalación, guarde este
manual en un lugar fácilmente accesible.
INFORMACIÓN DE SEGURIDAD
21 Salvaguardias importantes
CARACTERÍSTICAS DEL PRODUCTO
24 Características principales
25 Detalle del panel de control
26 Purificación de aire en cinco etapas
FUNCIONAMIENTO
27 Preparación para el primer uso
28 Funcionamiento del producto
MANTENIMIENTO
30 Vida útil del filtro y plan de limpieza
31 Limpieza del sensor de aire
32 Reemplazo de los filtros
INFORMACIÓN TÉCNICA
33 Solución de problemas
35 Especificaciones del producto
36 Garantía
37 Información de contacto
TRADUCCIONES
2 Inglés
38 Francés
MANUAL DEL PROPIETARIO DEL BRONDELL PRO SANITIZING
AIR PURIFIER CON TECNOLOGÍA AG+ DE AURABEAT
Índice
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56

brondell Pro Filter Replacement Pack Le manuel du propriétaire

Catégorie
Purificateurs d'air
Taper
Le manuel du propriétaire
Ce manuel convient également à