Smith RTS/HE Manuel utilisateur
- Catégorie
- Cheminées
- Taper
- Manuel utilisateur
SERIES 28RTS/HE
GAS OR OIL WATER BOILER
INSTALLATION & OPERATING
INSTRUCTIONS
DESIGNED AND TESTED ACCORDING TO A.S.M.E. BOILER AND PRESSURE
VESSEL CODE, SECTION IV FOR A MAXIMUM ALLOWABLE WORKING PRESSURE
OF: 80 PSI, 552 kPa.
WARNING: If the information in this manual is not followed exactly, a re or explo-
sion may result causing property damage, personal injury or loss of life.
Do not store or use gasoline or other ammable vapors and liquids in the vicinity of
this or any other appliance.
WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electrical switch. Do not use any phone in your building.
• Immediately call your gas supplier from a phone outside of the building. Follow the
gas supplier’s instructions.
• If you cannot reach your gas supplier, call the re department.
Installation and service must be performed by a qualied installer, service agency or
the gas supplier.
TEL. (413) 562-9631 FAX (413) 562-3799
RTS-IOM-6
82-7013
WARNING: The only liquid fuel to be used in this boiler is #2 fuel oil. Never use
gasoline, crankcase drainings, oil containing gasoline or any other liquid fuels in the
boiler! Never burn garbage or paper in the boiler! Failure to comply with this warning
can result in an explosion or re causing extensive property damage, severe personal
injury or death!
INSTALLER, READ THESE INSTRUCTIONS CAREFULLY. THEY WILL SAVE YOU VALUABLE TIME WHEN
ASSEMBLING THE BOILER. THESE INSTRUCTIONS TO BE AFFIXED ADJACENT TO THE BOILER.
CONSUMER, RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE PURPOSES.
FOR JACKET ASSEMBLY AND BURNER SET UP SEE SEPARATE INSTRUCTIONS.
9/18
Page 2 SERIES 28RTS/HE BOILER INSTALLATION AND OPERATION INSTRUCTIONS
AVERTISSMENT. Assurez-vous de bien suivre les instructions données dans cette
notice pour réduire au minimum le risque d’incendie ou d’explosion ou pour éviter tout
dommoge matériel, toute blessure ou la mort
Ne pas entreposer ni utiliser d’essence ou ni d’autres vapeurs ou liquides inammables
à proximité de cet appareil ou de tout autre appareil.
QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ:
• Ne pas tenter d’allumer d’appareil.
•
Ne touchez à aucun interrupteur; ne pas vous servir des téléphones se trouvant dans le
bâtiment.
• Appelez immédiatement votre fournisseur de gas depuis un voisin. Suivez les ins-
tructions du fournisseur.
• Si vous ne purvez rejoindre le fournisseur, appelez le service des incendies.
L’installation et l’entretien doivent être assurés par un installateur ou un service
d’entretien qualié ou par le fournisseur de gaz.
CONTENTS
Before You Start .................................................page 2
Boiler Ratings & Capacities ................................ page 3
Boiler Location ....................................................page 3
Combustion Air & Ventilation .............................. page 4
Chimney & Vent Pipe Connections..................... page 5
Common Vent Systems ...................................... page 7
Boiler Assembly ................................................. page 8
General Piping Requirements .......................... page 16
Water Boiler Piping ........................................... page 17
Burner Installation.............................................page 21
Electrical Wiring ................................................page 21
Boiler Operation............................................... page 21
Boiler Checking & Adjustment .......................... page 22
Boiler Maintenance ........................................... page 23
Water Treatment ............................................... page 23
Repair Parts .....................................................page 25
Health Warnings ............................................... page 27
BEFORE YOU START
This manual covers the assembly, installation, operation
and maintenance of a Series RTS/HE hot water boiler.
The 28RTS/HE Series boilers are supplied completely
knocked down for eld assembly, knocked down but
with an assembled block or as complete factory
assembled packaged boilers. All boiler components
should be inspected for damage upon receipt. Any
damage should be immediately reported to the trucker
or wholesaler. All boiler components should be stored in
a clean dry area. To obtain the safe, dependable,
efcient operation and long life for which this boiler was
designed, these instructions must be read, understood
and followed.
The Series 28RTS/HE boilers have been design
certied by CSA. Each unit has been constructed and
hydro-statically tested for a maximum working pressure
of 80 psi for water in accordance with Section IV of the
A.S.M.E. Boiler and Pressure Vessel Code for cast iron
boilers.
All aspects of the boiler installation must conform to the
requirements of the authority having jurisdiction, or, in
the absence of such requirements, to the National Fuel
Gas Code, ANSI Z223.1/NFPA 54-latest revision or to
the Installation of Oil Burning Equipment, ANSI/NFPA
31.
Where required by the authority having jurisdiction, the
installation must conform to the Standard for Controls
and Safety Devices for Automatically Fired Boilers,
ANSI/ASME CSD-1.
In Canada, the installation must be in accordance with
the requirements of CAN/CGA B149.1 or .2, Installation
Code for Gas Burning Appliances and Equipment.
In the Commonwealth of Massachusetts the installation
of a gas burner must be performed by a licensed
plumber or gas tter.
The owner should maintain a record of all service work
performed with the date and a description of the work
done. Include the name of the service organization for
future reference.
Direct all questions to your Smith Cast Iron Boiler
distributor or contact the Smith Customer Service
Department. Always include the model and serial
numbers from the rating plate of the boiler in question.
Page 3
SERIES 28RTS/HE BOILER INSTALLATION AND OPERATION INSTRUCTIONS
4. The boiler should be installed on a level, flat,
concrete oor or pad that is structurally sound and
will support the weight of the boiler. If a concrete
pad is used it must be at least 2 in., 51 mm thick.
Never install the boiler on a concrete oor or pad
that contains wires, cables, water pipes or hoses.
This boiler is designed for non combustible
oors!
WARNING: Never install a RTS boiler on top of
combustible flooring without consulting the
local building authorities for proper installation
guidelines! A minimum clearance of 6 in.,
0.15 m must be maintained between the boiler
and combustible construction. Failure to comply
with this warning may result in a re causing
extensive property damage, severe personal
injury or death!
5. DO NOT install this boiler in a location that would
subject any of the electrical components to direct
contact with water or excessive moisture during
operation or servicing.
6. DO NOT place this boiler in a location that would
restrict the introduction of combustion air into the
boiler.
WARNING: Never store combustible materials,
gasoline or any product containing ammable
vapors or liquids in the vicinity of the boiler.
Failure to comply with this warning can result in
an explosion or re causing extensive property
damage, severe personal injury or death!
BOILER RATINGS & CAPACITIES
Before undertaking the installation of the RTS Series
boiler check the boiler rating plate to ensure that the
boiler has been sized properly for the job. The “Net
Ratings” specify the equivalent amount of direct cast
iron radiation that the boiler can supply under normal
conditions. Also ensure that the boiler has been set up
for the type of fuel available at the installation site.
BOILER LOCATION
IMPORTANT NOTE!
A minimum distance of 3 ft, 0.9 m, must be main-
tained between the Back Section return port and
adjacent construction behind the boiler to allow for
RTS installation and removal, Figures 1 & 16.
1. Locate the boiler in an area that provides good
access to the unit. A minimum distance of 6 in.,
0.15m must be maintained between the boiler
and combustible construction. Servicing may
require the removal of jacket panels so service
clearances should be maintained. Allow a minimum
clearance of 3 ft., 0.9 m between adjacent con-
struction and the left side, front and smoke hood. A
minimum clearance of 3 ft., 0.9 m should be main-
tained between adjacent construction and the right
side and back of the boiler. Accessibility clearances
should take precedence over minimum clearances
to combustible construction, Figure 1.
2. An optimum site will be level, central to the piping
system, close to a chimney and have adequate
fresh air for combustion.
3. Never install the boiler on carpeting.
Figure 1 -Service Clearances to Adjacent
36"
6"
6"
36"
18"
6 " FROM ALL SIDES
OF EXHAUST VENT
24"
36"
SIOM-104 Rev A
36"
Construction
Page 4 SERIES 28RTS/HE BOILER INSTALLATION AND OPERATION INSTRUCTIONS
The bottom opening must be within 12 in., 305 mm
of, but not less than 3 in., 76 mm from, the bottom of the
enclosure.
All Air From Outside The Building
When installed in a conned space two permanent
openings communicating directly with, or by ducts to,
the outdoors or spaces that freely communicate with
the outdoors must be present. The upper opening must
be within 12 in., 305 mm of, but not less than 3 in.,
76 mm from, the top of the enclosure. The bottom
opening must be within 12 in., 305 mm of, but not less
than 3 in., 76 mm from, the bottom of the enclosure.
Where directly communicating with the outdoors or
communicating with the outdoors through vertical ducts,
each opening shall have a minimum free area of
1 in2/4000 Btu/hr, 35 in2/GPH, 550 mm2/kW of the total
input rating of all of the equipment in the enclosure.
Where communicating with the outdoors through
horizontal ducts, each opening shall have a minimum
free area of 1 in2/2000 Btu/hr, 70 in2/GPH, 1100 mm2/
kW of the total input rating of all of the equipment in the
enclosure. When ducts are used, they must have the
same cross-sectional area as the free area of the
opening to which they connect. When calculating the
free area necessary to meet the make-up air
requirements of the enclosure, consideration must be
given to the blockage effects of louvers, grills and
screens. Screens must have a minimum mesh size of
1/4 in, 6.4mm. If the free area through a louver or grill
is not known the louver or grille should be sized per
Table 1.
Table 1 - Make-up Air Louver Sizing
Required Cross Sectional Louver Area (in2)
Metal Wooden
Input 1/4", 6.4 mm Louvers Louvers
(MBH) Wire Screen 75% Free Area 25% Free Area
in2 cm2 in2 cm2 in2 cm2
1000 250 1613 333 2148 1000 6452
1200 300 1936 400 2578 1200 7742
1400 350 2258 467 3007 1400 9033
1600 400 2581 533 3437 1600 10,323
1800 450 2903 600 3866 1800 11,614
2000 500 3226 666 4296 2000 12,904
2200 550 3549 733 4726 2200 14,194
2400 600 3871 800 5155 2400 15,485
2600 650 4194 867 5585 2600 16,775
2800 700 4516 934 6014 2800 18,066
3000 750 4838 1000 6452 3000 19,354
3200 800 5162 1066 6874 3200 20,646
3400 850 5484 1134 7303 3400 21,937
3600 900 5807 1200 7733 3600 23,227
3800 950 6129 1267 8162 3800 24,518
4000 1000 6452 1334 8592 4000 25,808
4200 1050 6775 1400 9022 4200 27,098
4400 1100 7097 1467 9451 4400 28,389
4600 1150 7420 1533 9881 4600 29,679
4800 1200 7742 1600 10,310 4800 30,970
COMBUSTION AIR & VENTILATION
WARNING: This boiler must be supplied with
combustion and ventilation air in accordance
with the latest revision of Section 5.3, Air for
Combustion & Ventilation, of the National Fuel
Gas Code, ANSI Z223.1/NFPA 54 for gas boilers
or ANSI/NFPA 31 Installation of Oil Burning
Equipment for oil boilers. Canadian installations
must comply with CAN/CSA B149.1 Natural Gas
and Propane Installation Code for gas boilers
or CSA B140.7 Oil Burning Equipment for oil
boilers. All applicable local building codes
must be adhered to. Failure to provide adequate
combustion air for this boiler can result in
excessive levels of carbon monoxide which can
result in severe personal injury or death!
To operate properly and safely this boiler requires a
continuous supply of air for combustion. An adequate
supply of air must be available to replace the air used
by the combustion process. NEVER store objects on or
around the boiler.
CAUTION: Never use an exhaust fan in the boiler
room. The boiler room must never be under a
negative pressure or improper burner operation
will occur!
NOTE: Forced make-up air supplied to the boiler
room must be approved by the local authorities.
A minimum of 30 ft3/GAL, 0.22 m3/L for oil or
25 ft3/100 MBH (Therm), 0.024 m3/kW for gas must be
provided.
All Air From Inside The Buidling
If the boiler is to be located in a conned space mini-
mum clearances of 24 in., 610 mm must be maintained
between the boiler and any adjacent construction.
When installed in a conned space, two permanent
openings communicating with an additional room(s)
are required. The combined volume of these spaces
must have sufcient volume to meet the criteria for an
unconned space. The total air requirements of all fuel
burning equipment or any type of exhaust fan must be
considered when making this determination.
Each opening must have a minimum free area of
1 in2/1000 Btu/hr, 140 in2/GPH, 2200 mm2/kW based
on the total input rating of ALL fuel burning equipment in
the conned area. Each opening must be no less than
100 in2, 64,516 mm2 in size. The upper opening must be
within 12 in., 305 mm of, but not less than 3 in., 76 mm
from, the top of the enclosure.
Page 5
SERIES 28RTS/HE BOILER INSTALLATION AND OPERATION INSTRUCTIONS
CHIMNEY & VENT PIPE
CONNECTIONS
WARNING: The vent installation must be in
accordance with the latest revision of Part 7,
Venting of Equipment, of the National Fuel Gas
Code, ANSI Z223.1/NFPA 54 for gas boilers
or ANSI/NFPA 31 Installation of Oil Burning
Equipment for oil boilers and the ASHRAE
Equipment Handbook on Venting. Canadian
installations must comply with CAN/CSA
B149.1 Natural Gas and Propane Installation
Code for gas boilers or CSA B140.7 Oil Burning
Equipment for oil boilers. All applicable local
building codes must be adhered to. Improper
venting of this boiler can result in excessive
levels of carbon monoxide which can result in
severe personal injury or death!
CAUTION: The products of combustion from a
RTS must be safely vented to the outdoors
while ensuring that the flue gasses do not cool
prematurely. It’s critical that the chimney system
be properly designed to handle the relatively cool
ue gas temperatures. An oversized or uninsulated
chimney will cause the moisture in the ue gases
to condense resulting in damage to the chimney
system unless it’s specifically designed for
condensate. If this is the case a suitable condensate
drain must be used to protect the boiler from
condensate.
NOTE: Our warranty does not cover corrosion
damage to the boiler or its vent system caused by
ue gas condensate!
Chimney Inspection & Sizing
If this boiler will be connected to a masonry chimney, a
thorough inspection of the chimney must be performed.
Ensure that the chimney is clean, properly constructed,
lined and properly sized, see Figure 2. Table 2 lists the
equivalent breeching and ue sizes required for the RTS
& RTS/HE boilers.
Table 2 - Equivalent Breeching & Chimney Size
Boiler Size Breeching Size Chimney Size
in mm in mm
RTS-4 10 254 10 254
RTS-5 10 254 10 254
RTS-6 10 254 10 254
RTS-7 12 305 12 305
RTS-8 12 305 12 305
RTS-9 14 356 14 356
RTS-10 14 356 14 356
RTS-11 14 356 14 356
RTS-12 14 356 14 356
RTS-13 14 356 14 356
RTS-14 16 406 16 406
RTS-15 16 406 16 406
RTS-16 16 406 16 406
RTS-17 18 406 18 406
RTS-18 18 457 18 457
Note: These sizes are based on a 20 foot chimney height.
The 28RTS/HE Series is designed for pressurized
operation with a maximum back pressure of 0.10 in.,
2.54 mm WC before the smoke hood slide damper.
If the vent conguration results in a maximum back
pressure greater than this, the burner capacity may
have to be reduced. Contact the Smith Technical
Service Department to verify the burner capacity.
The chimney must be able to provide 0.10 in. WC at
the boiler outlet. If the chimney is 50 ft. or taller it may
produce excessive draft (appox. - 0.25 in. WC) and a
barometric draft regulator may be needed.
When more than one piece of combustion equipment is
connected to the same chimney ue, the ue must be
large enough to safely vent the combined output of all
the equipment.
WARNING: If an appliance using any type of
a mechanical draft system operating under
positive pressure is connected to a chimney
flue, never connect a Category I appliance
to this flue. Doing so can result in the
accumulation of carbon monoxide which can
cause severe personal injury or death!
Page 6 SERIES 28RTS/HE BOILER INSTALLATION AND OPERATION INSTRUCTIONS
The vent materials used in positive pressure
vent systems must be certified to UL 1738 for
installations in the United States, ULS636 for
installations in Canada. The following manufactures
have systems that meet these requirements:
Heat-Fab, Inc.
38 Hayward Street
Greeneld, MA 01301, (800) 772-0739.
Z-Flex U.S., Inc.
20 Commerce Park
North, Bedford, NH 03110-6911, (800) 654-5600.
Protech Systems Inc.
26 Gansevoort Street
Albany, NY 12202 (518) 463-7284
WARNING: Breeching under positive pressure
must be certied to UL 1738 for installations
in the United States, ULS636 for installations
in Canada. Type B1 vent SHALL NOT be used.
Failure to comply with this warning can result in
severe personal injury or death.
VENT CONNECTIONS
WARNING: Never modify or alter any part of the
boiler’s smoke hood. This includes the removal
or alteration of any bafes. Never install a vent
pipe of a diameter smaller than that of the boiler
smoke hood outlet. Failure to comply with this
warning can result in severe personal injury or
death.
Locate the boiler as close to the chimney as possible.
Use the shortest, straightest vent connector possible
for the installation. If horizontal runs exceed 5 ft., 1.5 m
they must be supported at 3 ft., 0.9 m intervals with
overhead hangers. Use a single wall stainless or single
wall galvanized steel vent pipe the same diameter as
the ue collar to connect the boiler to a masonry chimney.
When using an approved metal chimney system use the
appropriate vent connector. The vent connector should
be sloped up toward the chimney at a minimum rate of
1/4 in/ft, 2 cm/m. On masonry chimneys the connector
must terminate ush with the inside of the chimney ue.
Fasten each single wall vent connection with at least 3
corrosion resistant sheet metal screws.
Figure 2- Vertical Venting
Page 7
SERIES 28RTS/HE BOILER INSTALLATION AND OPERATION INSTRUCTIONS
c) Insofar as is practical, close all building doors and
windows and all doors between the space in which
the appliances remaining connected to the common
venting system are located and other spaces of the
building. Turn on clothes dryers and any appliance
not connected to the common venting system. Turn
on any exhaust fans, such as range hoods and
bathroom exhaust, so they will operate at maximum
speed. Do not operate a summer exhaust fan for a
boiler installation. Close replace dampers.
Dans la mesure du possible, fermer toutes les
portes et les fenêtres du bâtiment et toutes les
portes entre l'espace où les appareils toujours
raccordés du système d'évacuation sont installés
et les autres espaces du bâtiment. Mettre en
marche les sécheuses, tous les appareils non
raccordés au système d'évacuation commun et
tous les ventilateurs d'extraction comme les hottes
de cuisinère et les ventilateurs des salles de
bain. S'assurer que ces ventilateurs fonctionnent
à la vitesse maximale. Ne pas faire fonctionner
les ventilateurs d'été. Fermer les registres des
cheminées.
d) Place in operation the appliance being inspected.
Follow the lighting instructions. Adjust thermostat
so appliance will operate continuously.
Mettre l'appareil inspecté en marche. Suivre les
instructions d'allumage. Régler le thermostat de
façon que l'appareil fonctionne de façon continue.
e) Test for spillage at the draft hood relief opening after
5 minutes of main burner operation. Use the ame
of a match or candle, or smoke from a cigarette,
cigar or pipe.
Faire fonctionner le brûleur principal pendant 5
min ensuite, déterminer si le coupetirage déborde
à l'ouverture de décharge. Utiliser la amme d'une
allunette ou d'une chandelle ou la fumée d'une
cigarette, d'un cigare ou d'une pipe.
Always provide a minimum clearance of 6 in., 152 mm
between single wall metal vent pipe and all combustible
materials.
WARNING: Failure to maintain minimum
clearances between vent connectors and any
combustible material can result in a re causing
extensive property damage, severe personal
injury or death!
COMMON VENT SYSTEMS
If an existing boiler is removed from a common venting
system, the common venting system may then be too
large for the proper venting of the remaining appliances
connected to it. At the time of removal of an existing
boiler, the following steps shall be followed with each
appliance remaining connected to the common venting
system placed in operation, while the other appliances
remaining connected to the common venting system are
not in operation.
Au moment du retrait d'une chaudière existante, les
mesures suivantes doivent être prises pour chaque
appareil toujours raccordé au système d'évacuation
commun et qui fonctionne alors que d'autres appareils
toujours raccordés au système d'évacuation ne
fonctionnent pas: système d'évacuation
a) Seal any unused openings in the common venting
system.
Sceller toutes les ouvertures non utilisées du
système d'évacuation.
b) Visually inspect the venting system for proper size
and horizontal pitch and determine there is no
blockage or restriction, leakage, corrosion and other
deciencies which could cause an unsafe condition.
Inspecter de façon visuelle le système d'évacuation
pour déterminer la grosser et l'inclinaison
horizontale qui conviennent et s'assurer que le
système est exempt d'obstruction, d'étranglement
de fruite, de corrosion et autres défaillances qui
pourraient présenter des risques.
Page 8 SERIES 28RTS/HE BOILER INSTALLATION AND OPERATION INSTRUCTIONS
f) After it has been determined that each appliance
remaining connected to the common venting
system properly vents when tested as outlined
above, return doors, windows, exhaust fans,
fireplace dampers and any other gas-burning
appliance to their previous condition of use.
Une fois qu'il a été d éterminé, selon la métode
indiquée cidessus, que chaque appareil raccordé
au système d'évacuation est mis à l'air libre de
façor adéquate. Remettre les portes et les fenêtres,
les ventilateurs, les registres de cheminées et les
appareils au gaz à leur position originale.
g) Any improper operation of the venting system
should be corrected so the installation conforms
with the National Fuel Gas Code, ANSI Z223.1/
NFPA 54 or ANSI/NFPA 31 Installation of Oil
Burning Equipment for oil burners. When resizing
any portion of the common venting system, the
common venting system should be resized to
approach the minimum size as determined using the
appropriate tables in
Appendix F in the National Fuel Gas Code, ANSI
Z223.1/NFPA 54 and or CSA B149 Installation
Codes.
Tout mauvais fonctionnement du systéme
d'évacution commun devrait étré corrigé de façor
que l'installation soit conforme au National Fue
Gas Code, ANSI Z223.1/NFPA 54 et (ou) aux
codes d'installation CAN/CGA-B149 or ANSI/NFPA
31 Installation of Oil Burning Equipment for oil
burners. Si la grosseur d'une section du système
d' évacuation doit étré modiée, le système devrait
étré modié pour respecter les valeurs minimales
des tableaux pertinents de l'appendice F du
National Fuel Gas Code, ANSI Z223.1/NFPA 54 et
(ou) des codes d'installation CSA-B149.
BOILER ASSEMBLY
Locate the boiler installation site based on the guide-
lines set forth in the BOILER LOCATION section.
WARNING: Never install a RTS Series boiler on
top of comustible ooring without consulting
the local building authorities for proper
installation guidelines! Failure to comply
with this warning can result in a re causing
extensive property damage, severe personal
injury or death!
IMPORTANT NOTE!
A minimum distance of 3 ft., 0.9 m, must be main-
tained between the Back Section return port and
adjacent construction behind the boiler to allow for
RTS installation and removal, Figures 1.
Packaged Boilers/Factory Assembled Sections
A careful inspection of all assemblies should be made to
detect possible shipping damage. Packaged boilers and
factory assembled blocks of sections are hydrostatically
tested at the factory to insure pressure tightness. A
hydrostatic retest should be performed before any piping
connections are made to detect leaks caused by
shipping.
NOTE: All assembled boiler sections shall pass the
hydrostatic tests prescribed in Section IV of the
ASME Boiler and Pressure Vessel Code.
CAUTION: Do not connect any boiler controls
during the pressure test or they will be damaged!
Page 9
SERIES 28RTS/HE BOILER INSTALLATION AND OPERATION INSTRUCTIONS
2. Carefully place the back section in position on the
angles as shown in Figure 4.
WARNING: The section MUST be fully supported
to prevent it from falling! Failure to comply
with this warning may result property damage,
severe personal injury or death!
Figure 4 - Section Placement
3. Clean the hydronic port connector sealing surfaces
and the rope grooves with a wire brush to remove
any rust or debris.
4. Apply two coats of the spray adhesive supplied with
the boiler to the rope groove. Allow time for the rst
coat to dry before applying the second coat. When
the second coat is tacky press the rope into the rope
groove. Trim the rope off leaving 1/8 in., 3.2 mm
extending beyond the surface of the cast iron
section, Figure 5.
Figure 5 - Rope Installation
Completed boilers must be tested as follows:
Water Boilers – the assembled boiler sections shall be
subjected to a hydrostatic test pressure of not less than
1-1/2 times the maximum allowable working pressure.
The hydrostatic pressure shall not exceed the required test
pressure by more than 10 psig, 70 kPa during the test.
WARNING: Never leak test the boiler using
compressed air! Failure to comply with this
warning may result in property damage, severe
personal injury or death!
1. Plug all openings in the boiler and ll it with water.
2. Bleed any air off through one of the top tappings
then increase the pressure as outlined above.
3. Maintain the test pressure while carefully checking
for leaks. If a leak is found it must be eliminated,
see Table 4 and supporting text. Once the
assembled boiler sections pass the hydrostatic test
drain them and remove the plugs from any tappings
that will be used in service.
NOTE: The shipping lugs, lifting lugs and metal
banding should be removed before installing the
jacket on factory assembled sections.
CAUTION: Remove the left jacket panels on fully
packaged boilers and ensure that the cleanout
covers are secure and gas tight. Loose covers could
damage the boiler.
Assembly of Knocked-Down Boilers
Drilled and tapped steel angles are furnished to provide
a level footing, ease of section assembly and a point of
jacket attachment.
1. Set the angles as shown in Figure 3. They must be
parallel and level. Grout under the angles to provide
a continuous bearing surface.
Figure 3 - Steel Angle Placement
MIN.- FLUSH
MAX. 3/8
INTER.
SECTION
BACK
SECTION
FLOOR ANGLE
FIXED NUT-NO WASHER
DO NOT TORQUE
WASHER ON SIDE TO BE
TORQUED. USE ANTISIZE
ON THREADS
Page 10 SERIES 28RTS/HE BOILER INSTALLATION AND OPERATION INSTRUCTIONS
5. Insert the large port connector with its steel inner
ring into the upper port.
6. Insert the two round port connectors into the lower
ports with steel inner ring.
NOTE: Apply the spray adhesive supplied with the
boiler to the port recess to hold the port connector
in place if necessary.
7. Select the correct intermediate section and carefully
move it into place against the back section, Figure
4.
NOTE: A putty knife or similar tool can be used to
hold the port connectors in place while the
intermediate section is positioned. It must be
removed before the sections make contact or the
port connector will be damaged resulting in a leak!
8. Insert the four draw rods through the casting
bosses. Thread nuts onto one end of the rods.
Place washers on the other end of the rods before
threading nuts onto them see Figure 4. Snug the
nuts nger tight. Use a spirit level to ensure that the
rst two sections are plumb and properly aligned,
Figure 6. Check the rope to insure that it’s properly
positioned. Once the sections are plumb and the
rope and port connectors are properly positioned
follow the torque sequence shown in Table 4.
Use anti-seize on draw rod and washer, coating thread
and washer on one end only. Torque the draw rods from
the end with anti-seize & washer. Follow the steps as
described below. Do not completely tighten one side;
gradually work each side using an alternating pattern until
the correct torque is reached.
Figure 6 - Section Alignment
Table 4 - Section Torque Sequence
Step Rod Position Torque
ft lbs Nm
1 Upper Right 25 34
2 Lower Left 25 34
3 Lower Right 25 34
4 Upper Left 10 14
5 Upper Right 50 68
6 Lower Left 50 68
7 Lower Right 50 68
8 Upper Right 75 102
9 Lower Left 75 102
10 Lower Right 75 102
11 Upper Left 30 42
12 Upper Right 125 169
13 Lower Left 125 169
14 Lower Right 125 169
15 Upper Right 125 169
16 Upper Left 40 54
NOTE: With these initial torques the sections may
not be metal to metal, which is acceptable. If any of
the ports leak during the hydrostatic test the torque
can be increased to 200 ft lbs, 271 Nm on the upper
right rod. The torque on the lower left and right rods
can be increased to 150 ft lbs, 203 Nm. Once the
sections are metal to metal additional torque will not
improve the seal.
RTS Support Bracket Location
The RTS SUPPORT BRACKET(S) MUST BE INSTALLED
DURING BOILER ASSEMBLY in the locations shown
in Table 3.
Insert the support bracket through the upper port
opening, rotate it sideways and hook one ear over the
center of the stay, then the other, Figure 7.
Figure 7 - RTS Support Bracket Installation
Page 11
SERIES 28RTS/HE BOILER INSTALLATION AND OPERATION INSTRUCTIONS
Push the bracket towards the back of the section
compressing the bracket until the front ears are in the
middle of the stay. Twist the bracket sideways hooking
one ear then the other. Release the bracket and let it
spring into position, Figure 8.
Figure 8 - RTS Support Bracket Installation
9. Assemble the rest of the sections following steps 3
through 8 above.
10. Hydrostatically test the boiler by following the
instructions on page 8.
11. While the boiler is being lled conrm that all
of the draw rods are properly torqued and that
there are no leaks.
12. If any leaks are found tighten the draw rods on that
section until the leak stops.
Heat Transfer Rod Installation, (For HE Models
only),
Figure 9
The high efficiency 28RTS/HE comes with design
certied heat transfer rod sets. Each tube of 15 heat
transfer rods will bafe one ue. In order to obtain the
high efciency for which the boiler was designed, the
heat transfer rods must be properly installed Figure 9.
Figure 9 - Heat Transfer Rod Installation
Boiler Section Location Numbered From Front To Back
Model 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
4 F SB H B F Front Section
5 F H SB H B SB Intermediate Section w/ Support Bracket
6 F SB H P H B H Intermediate Section w/ Heater Opening
7 F SB H P P H B P Intermediate Section, Plain
8 F P H SB H P H B B Back Section
9 F P H SB H P P H B
10 F H P H SB H P P H B
11 F H P H SB P P P P H B
12 F H SB H P P H SB H P H B
13 F H SB H P H P P SB H P H B
14 F H SB H P H P H SB H P P H B
15 F H SB H P H P T H SB H P P H B
16 F H P H SB H P H P H SB H P P H B
17 F H P H SB H P H P H SB H P H P H B
18 F H P H SB H P H P P H SB H P H P H B
Table 3 - RTS Support Bracket Locations
Page 12 SERIES 28RTS/HE BOILER INSTALLATION AND OPERATION INSTRUCTIONS
Cleanout Cover Installation
1. The cleanout covers come insulated from the
factory. Inspect the covers to ensure that the
insulation is not damaged or missing. If it is call the
Smith Customer Service Department.
2. Trim the 1/2 in. rope that’s sticking out around the
cleanout opening ush with the castings to insure an
air-tight seal, see Figure 6.
3. Install the cleanout cover bolts from the bafed side
of the cleanout cover and start the nuts, Figure 9.
4. Rotate the bolts so the cam heads t between the
cleanout cover bosses on the castings.
5. Insert the cleanout cover and tighten the nuts to
15 ft lbs, 21 Nm.
6. Apply a bead of high temperature silicone caulk
around the perimeter of the cleanout cover to
ensure an air tight seal.
Figure 10 - Cleanout Cover Assembly (Typical)
Burner Mounting Plate Installation, Figure 11
1. Apply two coats of the spray adhesive supplied with
the boiler to the rope groove on the plate. Allow time
for the rst coat to dry then apply the second coat.
When the second coat is tacky lay the 3/8 in.rope
into the rope groove and press in place.
2. Screw the four 7/16-14 x 2-1/2 in. studs into the
tapped holes in the boiler front section.
3. Install the burner mounting plate insulation block in
the burner opening in the front section of the boiler.
The small observation port cutout must be on the
top, left side.
4. Position the front jacket panel frame over the four
studs.
Page 13
SERIES 28RTS/HE BOILER INSTALLATION AND OPERATION INSTRUCTIONS
Observation Port Assembly, Figure 12
1. Position the hinged end of the steel apper door,
item 5, over the boss on the observation port cover,
item 4.
2. Drive the expansion pin, item 7, through the hinge
bosses to secure the door to the cover.
3. Insert the hex bolt, item 6, through the hole in the
observation port cover.
4. Install the spring, nut and knob, items 3, 2 & 1 on
the bolt as shown. Use the nut, item 2, as a jam nut
against the knob, item 1.
5. Apply the insulating tape to the back of the
observation port cover as shown.
Figure 11 - Burner Mounting Plate Details
Figure 12 - Observation Port Assembly
Page 14 SERIES 28RTS/HE BOILER INSTALLATION AND OPERATION INSTRUCTIONS
Observation Port Installation
1. Screw the four 5/16-18 x 1-1/2 in. studs into the
tapped holes around the observation cover opening
in the back section.
2. Place the observation port cover assembly over the
studs and install the washers and nuts. Tighten the
nuts uniformly.
Smokehood Installation, Figure 13
1. Screw the four 5/16-18 x 1-1/2 in. studs into the
tapped holes around the smokehood opening in the
back section.
2. Apply smokehood insulation tape to smokehood.
3. Place the smokehood over the studs and install the
washers and nuts. Tighten the nuts uniformly.
4. Apply the 1/8 in. x 3/4 in. x 18 in. strip of insulating
tape to the damper anchoring angle.
5. Fully open the slide damper and leave it ready for
adjustment during burner light off.
6. Install thermometer (stack temperature gauge).
Figure 13 - Smokehood Assembly
Page 15
SERIES 28RTS/HE BOILER INSTALLATION AND OPERATION INSTRUCTIONS
Tankless Heater Installation - Optional
1. Clean the heater flange to remove any rust or
debris.
2. Install the four 7/16 in. x 1-1/2 in. studs into the
tapped holes in the tankless heater ange on the
section, Figure 14.
Figure 14 - Tankless Heater Installation
3. Place the heater gasket over the studs and carefully
install the heater.
4. Install the nuts and tighten evenly to ensure uniform
compression of the gasket.
5. Install the operating control in one of the heater
mounting plates to ensure quick burner response
when there is a demand for hot water. Figure 15
illustrates an acceptable piping arrangement for
multiple heaters.
Burner Mounting
1. Clean the burner mounting flange to remove any
rust or debris.
2. Install the four 3/8 in. x 1-1/4 in. studs into the
tapped holes in the burner mounting plate.
3. Use a hacksaw blade, or some other suitable tool,
to properly size the opening in the burner mounting
plate insulation block to match the burner air tube
end diameter.
NOTE: The opening should be a close t, but not too
snug or the insulation block may be damaged upon
burner insertion!
4. Place the burner gasket, supplied with the burner,
over the studs and carefully insert the burner into
the opening in the burner mounting plate.
CAUTION: Most burners require support to the oor.
Follow the burner manufacturer's instructions or the
burner may be damaged!
5. Install the 3/8 in. washers and nuts and tighten
securely.
Figure 15 - Multiple Tankless Heater Piping
Page 16 SERIES 28RTS/HE BOILER INSTALLATION AND OPERATION INSTRUCTIONS
If a boiler is installed above any radiation elements it must
be tted with a low water cutoff device.
Relief & Safety Valve Piping
Install the pressure relief or safety valve in the 3 in NPT
opening in the top of the back section, Figure 18 and
Table 5. Use bushings as needed.
WARNING: The discharge of the pressure relief
or safety valve must be piped to the oor to
prevent scalding in the event of a discharge, see
Figure 16. The discharge piping must be sized
the same as the pressure relief or safely valve
outlet. Never install any type of valve between
the boiler and the pressure relief or safety valve!
Failure to comply with this warning can result in
an explosion causing extensive property damage,
severe personal injury or death
Figure 17 - Front Section Tapping Locations
Figure 18 - Back Section Tapping Locations
GENERAL PIPING REQUIREMENTS
CAUTION: Never use automotive antifreeze in the
boiler or heating system. If antifreeze is necessary
it must be formulated specifically for hydronic
heating systems, such as ethylene or propylene
glycol. Failure to comply with this caution will void
the warranty!
All heating system piping must be installed by a qualied
technician in accordance with the latest revision of the
ANSI/ASME Boiler and Pressure Vessel Code, Section
IV or CSA B51. Also ANSI/ASME CSD-1, Standard for
Controls and Safety Devices for Automatically Fired
Boilers where required. All applicable local codes and
ordinances must also be followed. A minimum clearance
of 1 in., 25 mm must be maintained between heating
system pipes and all combustible construction.
CAUTION: Improper piping of this boiler can result in
poor performance and premature failure of the boiler
voiding the warranty! Improper piping can also cause
ooding and extensive property damage!
Ensure that the boiler is level from front to back and from
side to side. Use metal shims to level the boiler. NEVER
use wood, plastic or other combustible materials as shims.
Figure 16 - Relief & Safely Valve Piping
11
10
9
7
5
6
4
3
1
2
Page 17
SERIES 28RTS/HE BOILER INSTALLATION AND OPERATION INSTRUCTIONS
Table 5 - Water Tappings
WATER BOILER PIPING - RTS
IMPORTANT NOTE!
A minimum distance of 3 ft., 0.9 m, must be maintained
between the Back Section return port and adjacent
construction behind the boiler to allow for RTS
installation and removal, Figures 1 & 18.
NOTE: See CLEANING OF WATER BOILERS before
proceeding!
The supply and return connections should be sized to suit
the system, see Figures 17, 18 and Tables 5 & 6. Do not
pipe the supply from a bottom port or the return to the top
port, the boiler will not work properly. Typical water boiler
piping arrangements are shown in Figure 22. Swing joints
should be used.
Install 3 in. nipples into the two 3 in. NPT lower tappings
in the front section and cap them.
Supply Piping
Install a reducing bushing at the 5 in. ange in the upper
front section to obtain the correct supply pipe size, Figure
17 and Tables 5 & 6.
Table 6 - Water Boiler Piping Sizes
Boiler Size Return Size Supply Size
# Sections NPT NPT
4 & 5 3" 3"
6 through 9 4" 4"
10 through 18 5" 5"
Note: Sizes based on 20°F, 11.1°C, ∆T for the system.
Return Piping - RTS Installation
NOTE: Install the smoke hood before proceeding.
1.
Install 3 in. x 4 in. NPT bushings in the two 4 in NPT
tappings at the bottom of the back section. Install two 3
in NPT x 3 in. nipples with ball valves or caps, Figure 16.
2. Once the cast iron sections have been assembled
install the eight 3/4 in. x 3 in. studs in the upper rear
casting. Apply a thread sealant to the studs before
installing them, Figure 19.
Figure 19 - RTS Stud Installation
3. Install a ange gasket over the studs and insert the
end tube. Depending on the boiler size the end tube
will have two, three or four holes, Figure 20.
Figure 20 - End Tubes
Connect the next section per Table 7 using the brass
screws supplied, Figure 21.
NOTE: The large holes must all be facing in the
same direction for the tube to function properly.
Take care to guide the tube over the support bracket(s).
Attach the anged end section and slide the ange over
the studs, Figure 23.
NOTE: The tab on the RTS ange MUST be in the 9
O’clock position, Figure 23.
Tapping Size Water
1 1/8" Chamber Pressure
2 3/4" Probe LWCO
3 3/4" Temp./Pressure Gage
4 3/4" Operating Control - Top
5 3/4" Manuel Reset High Limit
6 1" Air Removal
7 5" Supply Flange
9 1 1/2"
10 1" Water Column - Bottom
11 3" Boiler Drain
12 4" Boiler Drain
13 3" Relief Valve
14 Return Flange
Page 18 SERIES 28RTS/HE BOILER INSTALLATION AND OPERATION INSTRUCTIONS
Table 7- RTS Component Table
Flanged 3 Hole 2 Hole 3 Hole 4 Hole Support
Model End Int. End End End Bracket
70-1201 70-1202 70-1203 70-1204 70-1205 03-1059
4 1 1 1
5 1 1 1
6 1 1 1
7 1 1 1 1
8 1 1 1 1
9 1 1 1 1
10 1 2 1 1
11 1 2 1 1
12 1 2 1 2
13 1 3 1 2
14 1 3 1 2
15 1 3 1 2
16 1 4 1 2
17 1 4 1 2
18 1 4 1 2
Figure 21 - RTS Installation
Figure 23 - RTS Installed
IMPORTANT NOTE!
A removable elbow or section of pipe must be
attached to the Back Section return port to allow for
RTS removal should maintenance be required. Shut
off valves should be used as required.
Install a ange gasket and companion ange or anged
elbow over the studs. Install and torque the nuts supplied
with the RTS. The boiler return piping should be sized per
Table 6. Figure 22 depicts a typical piping arrangement
for a multi boiler installation with the RTS.
Figure 22 - Typical Multiple Water Boiler Piping Arrangement
Page 19
SERIES 28RTS/HE BOILER INSTALLATION AND OPERATION INSTRUCTIONS
Cleaning Of Water Boilers
Normally the cleaning of water boilers is unnecessary
unless there is unusually heavy contamination of the
boiler or system.
The burner must be installed and made operational
along with the operating, limit and other safety controls.
The burner on oil boilers must be adjusted to prevent
sooting of the boiler ues.
Final burner adjustment should be made after the boiler
has been properly cleaned.
WARNING: The pressure relief valve must
be installed and piped to the oor to prevent
scalding in the event of a discharge, see Figure
16. The discharge piping must be sized the
same as the pressure relief valve outlet. Never
install any type of valve between the boiler and
the pressure relief valve! Failure to comply with
this warning can result in an explosion causing
extensive property damage, severe personal
injury or death!
Control Installation
Locate the temperature & pressure gage, low water cutoff,
high limit and operating controls per Figures 17 & 24 and
Table 5. Optional controls must be installed in accordance
with the control manufacturer’s instructions.
NOTE: The front jacket panel MUST be installed before
any controls are attached to the front boiler section!
CAUTION: The controls must be mounted in the correct
location and according to the control manufacturer’s
instructions or the boiler may not function properly!
Piping For Use With Cooling Units
The boiler, when used in connection with a refrigeration
system, must be installed so the chilled medium is piped
in parallel with the boiler. Appropriate valves must be
used to prevent the chilled water from entering the boiler.
When a boiler is connected to a heating coil that may be
exposed to refrigerated air from an air handling device, the
piping system must be equipped with ow-control valves
or some other automatic means of preventing gravity
circulation of the boiler water during the cooling cycle.
Figure 24 - Boiler Control Locations
Page 20 SERIES 28RTS/HE BOILER INSTALLATION AND OPERATION INSTRUCTIONS
1. Install ball valves on the two 3 in. NPT nipples in
the bottom of the front section and pipe to a suitable
drain.
2. Fill the boiler 3/4 full with water.
3. Make a cleaning solution by mixing 1 lb, 0.45 kg
each of caustic soda and trisodium phosphate for
every 50 ga, 189 L of water, Table 8.
Table 8- Boiler Water Content
Boiler Water Boilers
Model Gallons Liters
4 123 466
5 150 568
6 177 670
7 204 772
8 231 875
9 258 977
10 285 1079
11 312 1181
12 339 1283
13 366 1386
14 392 1484
15 419 1586
16 446 1689
17 473 1791
18 500 1893
NOTE: The water content of the heating system must
be added to the boiler water content.
CAUTION: Avoid skin contact with cleaning solution
to prevent injury! If eye or skin contact occurs ush
with large quantities of water.
NOTE: Some locations do not allow this solution
to be used. Check with the local authority having
jurisdiction.
4. Mix the cleaning chemicals with water to create a
concentrated solution. Pour the cleaning solution
through one of the top tappings in the front section
and plug it.
5. Immediately ll the rest of the boiler and the heating
system with water.
6. Fire the boiler and maintain a water temperature of
160°F to 200°F, (71°C to 93°C) it may be necessary
to cycle the boiler.
7. Run all of the system pumps during the cleaning
procedure.
WARNING: Monitor the boiler pressure constantly
during the cleaning procedure. Do not allow the
boiler pressure to exceed the pressure listed on
the pressure relief valve or a discharge of hot
water and steam will occur!
8. Shut the boiler off and allow the boiler to cool to
100°F, 38°C. Open the 3 in. ball valves and drain the
boiler and heating system.
9. Remove the 3 in. ball valves and install 3 in. pipe
caps on the ends of the 3 in. NPT nipples.
10. Rell the boiler and heating system with water.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
Smith RTS/HE Manuel utilisateur
- Catégorie
- Cheminées
- Taper
- Manuel utilisateur
dans d''autres langues
- English: Smith RTS/HE User manual
