Fluidwell E490 Le manuel du propriétaire
- Catégorie
- Mesure, test
- Taper
- Le manuel du propriétaire
E490-A-PL
MULTI-PURPOSE INDICATOR
Signal input: Connect to any sensor with 4-20mA output.
Isolated input circuit.
Loop mode: Ultra-low voltage drop < 1.5V.
Low voltage drop < 6.5V with backlight supply.
Power supply: Loop powered or external supply.
Backlight: Reduced from loop or full from external supply.
E-Series - Explosion proof indicators for hazardous areas
More info: www.fluidwell.com/eseries
E490-A-PL
Page 2 FW_E490-A-PL_M_v0302-03_EN
TABLE OF CONTENTS
1 ABOUT THIS MANUAL............................................................................................................ 4
1.1 How to use this manual .................................................................................................. 4
1.2 Use of pictograms ........................................................................................................... 4
1.3 Warranty and technical support ...................................................................................... 4
1.4 Model Reference ............................................................................................................ 4
2 SAFETY.................................................................................................................................... 5
2.1 Personal safety ............................................................................................................... 5
2.2 End-user responsibilities................................................................................................. 5
2.3 Potential equipment damage .......................................................................................... 5
2.4 Disposal of electronic waste ........................................................................................... 5
3 INTRODUCTION....................................................................................................................... 6
3.1 System description ......................................................................................................... 6
3.2 Product features ............................................................................................................. 7
3.3 Installation example ........................................................................................................ 8
4 OPERATION............................................................................................................................. 9
4.1 Introduction ..................................................................................................................... 9
4.1.1 Operating modes ............................................................................................................ 9
4.2 Control panel .................................................................................................................. 9
4.2.1 Display ............................................................................................................................ 9
4.2.2 Optical keys .................................................................................................................... 10
4.2.3 Backlight ......................................................................................................................... 11
4.3 Operator functions .......................................................................................................... 11
4.3.1 Functions of the keys in operator mode.......................................................................... 11
4.3.2 Selecting displayed information ...................................................................................... 12
4.4 Displayed information ..................................................................................................... 12
4.4.1 Process values ............................................................................................................... 12
4.4.2 Process limits.................................................................................................................. 13
4.5 Operator alarms .............................................................................................................. 13
4.5.1 Range error..................................................................................................................... 13
4.5.2 Internal error ................................................................................................................... 13
5 CONFIGURATION.................................................................................................................... 14
5.1 Introduction ..................................................................................................................... 14
5.2 Operating the Main Electronics Module (MEM) .............................................................. 14
5.2.1 Configuring using PC Configuration tool......................................................................... 15
5.2.2 Mechanical keys ............................................................................................................. 15
5.2.3 Optical keys switch ......................................................................................................... 15
5.3 Configuring using SETUP mode ..................................................................................... 16
5.3.1 Entering SETUP mode ................................................................................................... 16
5.3.2 Navigating the SETUP menu.......................................................................................... 16
5.3.3 Changing configuration settings ..................................................................................... 17
5.3.4 Returning to Operator Mode ........................................................................................... 18
5.4 SETUP menu overview................................................................................................... 18
5.5 SETUP menu explanations............................................................................................. 19
5.5.1 Menu 1: Value ................................................................................................................ 19
5.5.2 Menu 2: Display ............................................................................................................. 20
5.5.3 Menu 3: Sensor ............................................................................................................. 20
5.5.4 Menu 4: Others .............................................................................................................. 22
6 INSTALLATION........................................................................................................................ 23
6.1 Installation / environmental conditions ............................................................................ 23
6.2 Handling the E-Series enclosure .................................................................................... 24
6.2.1 Main parts ....................................................................................................................... 24
6.2.2 Identification.................................................................................................................... 25
6.2.3 Opening, assembling and closing the unit ...................................................................... 26
6.2.4 Test unit .......................................................................................................................... 27
6.3 Mechanical installation.................................................................................................... 27
6.3.1 Installation precautions ................................................................................................... 27
6.3.2 Mechanical dimensions .................................................................................................. 28
6.3.3 Mounting the unit ............................................................................................................ 29
E490-A-PL
FW_E490-A-PL_M_v0302-03_EN Page 3
6.4 Electrical installation ....................................................................................................... 30
6.4.1 Electrical precautions...................................................................................................... 31
6.4.2 Grounding of the enclosure ............................................................................................ 32
6.4.3 Electrical ratings ............................................................................................................. 33
6.4.4 Current loop mode and backlight brightness .................................................................. 33
6.4.5 Terminal connectors – MEM........................................................................................... 34
6.4.6 Terminals P1-P2: Power supply – type PL ..................................................................... 34
6.4.7 Terminals S1-S6: Input current loop – type A-PL ........................................................... 34
7 MAINTENANCE........................................................................................................................ 36
7.1 General directions........................................................................................................... 36
7.2 Instructions for repair ...................................................................................................... 36
7.3 Replace silica gel sachet ................................................................................................ 36
APPENDIX A - TECHNICAL SPECIFICATION .............................................................................. 37
A.1 General ........................................................................................................................... 37
A.2 Input................................................................................................................................ 38
A.3 Operational ..................................................................................................................... 38
A.4 Standards and approvals................................................................................................ 38
APPENDIX B - TROUBLESHOOTING ........................................................................................... 39
APPENDIX C - REMOTE CONFIGURATION TOOL ...................................................................... 40
C.1 Introduction ..................................................................................................................... 40
C.2 Cable connection ............................................................................................................ 40
C.3 Download and install....................................................................................................... 41
APPENDIX D - LEGAL INFORMATION ......................................................................................... 42
D.1 Declaration of Conformity ............................................................................................... 42
E490-A-PL
Page 4 FW_E490-A-PL_M_v0302-03_EN
1 ABOUT THIS MANUAL
1.1 HOW TO USE THIS MANUAL
This operation manual is divided into two main parts:
● The daily use of the E490-A-PL is described in Section 4: Operation[»9]. These instructions
are meant for users.
● All subsequent sections and appendices are meant for electricians/technicians. These provide a
detailed description of all software settings and hardware installation guidance.
Always follow the instructions in this manual, especially the safety information. For additional
information, please contact your supplier.
1.2 USE OF PICTOGRAMS
A hazardous situation may occur if the unit is not used for the purpose it was designed for or is used
incorrectly. The following pictograms inform you of important information:
A warning indicates a hazardous situation that could cause injury or death.
A caution indicates a condition that could cause:
● moderate/minor personal injury or equipment damage.
● incorrect functioning of the unit or connected instruments.
A note informs you of important information.
1.3 WARRANTY AND TECHNICAL SUPPORT
For warranty and technical support on your Fluidwell products, visit our internet site
www.fluidwell.com or contact us at [email protected].
1.4 MODEL REFERENCE
Hardware version: 13.03.xx
Software version: 03.07.xx
Document version: FW_E490-A-PL_M_v0302-03_EN
© Copyright 2023 Fluidwell B.V. - The Netherlands
Information in this document is subject to change without prior notice. The manufacturer is
not responsible for mistakes in this material or for incidental damage caused as a direct or
indirect result of the delivery, performance or use of this material.
© All rights reserved. No parts of this publication may be reproduced or used in any form or
by any means without written permission of your supplier.
E490-A-PL
FW_E490-A-PL_M_v0302-03_EN Page 5
2 SAFETY
2.1 PERSONAL SAFETY
● Explosion hazard: Never open the unit when explosive atmosphere is present, and the unit is
connected to a power supply or consuming device like an internal battery supply.
● Risk of electric shock: Only open the unit if all leads are free of potential electrical energy.
● Immediately inform the person responsible for the installation if you disagree with the safety
precautions or if you detect errors or danger.
2.2 END-USER RESPONSIBILITIES
● Installation, use, and servicing of the unit must be done by authorized technicians.
● This unit is not designed for use in life support appliances, devices, or systems where
malfunction of the product could result in personal injury. Customers using or selling these
products for use in such applications do so at their own risk and agree to fully indemnify the
manufacturer and supplier for any damages resulting from such improper use or sale.
● Check all connections, settings and technical specifications of all peripheral devices supplied
with the unit.
● The unit must be installed in accordance with the EMC (Electro Magnetic Compatibility)
guidelines.
● Connect Protective Earth (PE) / proper grouding to the metal enclosure as indicated in
Section 6.4.2: Grounding of the enclosure[»32].
● If the unit is used on a ship, truck or somewhere else with no Protective Earth (PE) connection
available, connect an alternative grounding suitable for the application to the metal enclosure.
● The Protective Earth (PE) wire (or alternative grounding) may never be disconnected or
removed.
● The local labor and safety laws, and regulations must be adhered to.
● Modifying the unit without prior written consent from the manufacturer will result in the
immediate termination of product liability and warranty period.
● The manufacturer accepts no responsibility whatsoever if the safety information and instructions
in this manual are not observed.
2.3 POTENTIAL EQUIPMENT DAMAGE
● Before installing the unit, check the mains voltage and information on the manufacturer's label
for product configuration.
● Electro Static Discharge (ESD) causes irreparable damage to electronics. When installing or
opening the unit, the technician should first discharge him- or herself by touching a well-
grounded object.
● Never touch the electronic components.
● Never expose the unit to conditions that may exceed the enclosure classifications as indicated
by the manufacturer's label and Section 6.1: Installation / environmental conditions[»23].
2.4 DISPOSAL OF ELECTRONIC WASTE
At the end of its life this product should be disposed of according to the
(inter)national regulations regarding waste electronic equipment. If a
battery is installed in this product, it should be disposed of separately. The
separate collection and recycling of your waste equipment will help to
conserve natural resources and ensure that it is recycled in a manner that
protects the environment.
E490-A-PL
Page 6 FW_E490-A-PL_M_v0302-03_EN
3 INTRODUCTION
3.1 SYSTEM DESCRIPTION
The E490-A-PL Multi-purpose indicator (also referred to as a unit) is an explosion proof
microprocessor-driven instrument designed to display process information from a 4-20mA signal,
like pressure, temperature, percentage, etc.
Fig.1: The E490-A-PL
This manual describes the daily use, configuration and installation of the loop powered, multi-
purpose indicator (with 4-20mA input from a sensor) and its available options. The following figure
shows the E490-A-PL used in a typical application.
any sensor with
4-20mA signal output
exisiting 4-20mA
current loop circuit
Remote Configuration Tool
+
-
Fig.2: Typical application
E490-A-PL
FW_E490-A-PL_M_v0302-03_EN Page 7
3.2 PRODUCT FEATURES
The main features of the unit are:
● User-friendliness: optical keys for through-the-glass operation (no need to touch the glass or
remove the cover).
● Bright backlight enables good readings in full sunlight and darkness.
● Usability: wide operational temperature, high ingress protection rating and international
certification.
● PC configuration software making configuration quick and easy.
● Rugged design for harsh environments: not just designed to be explosion proof.
● Aluminum enclosure with high quality industrial two component coating or stainless steel 316L
enclosure for offshore applications.
● Mounting flexibility: multiple solutions for sensor mounting, including 1” NPT or M25 bottom
entry; suitable for wall or pipe mount applications.
● Installation friendly design: spacious cabling area, plug and play cable connection and easy to
remove electronic module.
● 4-20mA current loop input terminals galvanically separated from the unit – backlight and
external supply are not connected to the loop.
● Very low voltage drop over the current loop input terminals.
● Ability to supply the backlight from the loop at reduced intensity.
● Possibility to connect a separate supply to drive the backlight at full intensity.
● Internal wire links provide terminals to interconnect the return line and wire shields. This makes
insertion into an existing loop easy without the need for an additional junction box.
Standard inputs
The E490-A-PL measures a single 4-20mA current loop signal four times per second with high
accuracy. The loop current, which is galvanically isolated from the unit, is also used to generate a
small supply signal to power the unit.
The loop can be configured in two energy modes which allows either an ultra-low voltage drop
across the input terminals or a higher voltage drop which can also drive the backlight.
See Section 6.4.4: Current loop mode and backlight brightness[»33] for more information.
Control panel
The unit is equipped with a control panel with three optical keys and a large backlit Liquid Cristal
Display (LCD) with various symbols and digits to display/control measurement units, status
information and key-word messages.
Configuration
The unit can be used for many types of application and has both a SETUP mode as well as a PC
connection for configuring it to your requirements. It includes several important features, such as
sensor configuration, measurement units and signal selection.
All settings are stored in an EEPROM memory so they will not be lost if there is a power failure.
E490-A-PL
Page 8 FW_E490-A-PL_M_v0302-03_EN
3.3 INSTALLATION EXAMPLE
Following parts can be recognized in below installation example.
1
2
6
4 5 9
7
3
8
Fig.3: Installation example E490-A-PL
1. Cover 4. Display 7. Grounding
2. Armed cable connection 5. Optical touch keys 8. Labels
3. Pipe mounting plate 6. Process mount 9. Closed cable entry
E490-A-PL
FW_E490-A-PL_M_v0302-03_EN Page 9
4 OPERATION
This unit may only be operated by authorized and trained personnel who have read and understood
this manual, particularly Section 2: Safety[»5].
4.1 INTRODUCTION
This chapter describes the daily use and operation of the E490-A-PL. For this, the unit is equipped
with a control panel that provides the operator with various functions, information and operating
modes.
4.1.1 OPERATING MODES
The following operating mode are available:
●OPERATOR-mode
This is the default mode of operation and mode indicator
RUN
is shown on the display. This
mode is available for all operators and gives access to most other modes. The available
functions and rights depend on the type of unit and configured settings. The unit will always
return to this mode when there is no user interaction for some time in any of the other modes.
●SETUP-mode
This mode allows to review all configuration settings using a SETUP-menu. The mode indicator
SETUP
is shown on the display and access can be restricted via a password. After selecting a
configuration item, it can be changed using the PROGRAM-mode.
●PROGRAM-mode
This mode is used to change settings in the SETUP-menu, enter values in OPERATOR-mode or
enter a password. When a setting is being changed, this is indicated by the mode indicator
PROG
on the display.
The following paragraphs describe the modes of operation in more detail. SETUP-mode and
PROGRAM-mode are described in Section 5: Configuration[»14].
4.2 CONTROL PANEL
The control panel is located on the front side of the E-Series and consists of the following parts:
● A Liquid Cristal Display (LCD) to show process values and various other information.
● Three optical keys (PROG, SELECT, CLEAR) to control the unit during operation.
● A backlight to illuminate the display.
When the front cover is removed (only during service in non-hazardous area), the following parts
also become available:
● The Main Electronics Module (MEM)
● Three mechanical keys to control the unit during service.
● A switch to completely disable the optical keys.
These parts are explained in Section 5.2: Operating the Main Electronics Module (MEM)[»14].
Explosion risk: never open the housing when explosive atmosphere is present.
Opening and servicing of the unit may only be carried out by authorized and trained personnel who
have read and understood this manual, particularly Section 2: Safety[»5].
4.2.1 DISPLAY
Inside the E490-A-PL, the current loop input is continuously processed in the background. The
relevant process information is then displayed on a selection of screens when the unit is in
OPERATOR-mode.
Normally, the information shown on the display is updated 8 times per second. For improved
readability of quickly varying input signals, the displayed process values are only refreshed 1 time
per second.
The display contains one line with large digits at the top and one line with small digits at the bottom.
The top line is mainly used to display key process information, while the bottom line usually displays
measurement unit and less important information or system messages.
Symbols to indicate the operating mode are also available. The following image shows this in more
detail:
E490-A-PL
Page 10 FW_E490-A-PL_M_v0302-03_EN
PROG SELECT CLEAR
2
3
6
8
5
4
1
7
Fig.4: Display layout and important symbols
1. Optical keys: PROG, SELECT, CLEAR 5. Alarm indication symbol
2. Small digits – bottom line 6. Optical keys activation indicator
3. Large digits – top line 7. Mode indicators:SETUP, RUN, PROG
4. Key lock symbol (for optical keys) 8. Speedometer
4.2.2 OPTICAL KEYS
The optical keys are used to control the unit ‘through the glass’ without the need to open the
enclosure. To activate an optical key, position a finger (clean and without gloves) in front of the glass
above the indicated area for PROG, SELECT or CLEAR. Correct key operation will result in the
activation indicator to show on the display. After the indicator is shown, the finger can be
removed and the selected key ‘is pushed’.
The optical keys only work reliably when the glass is clean. Try to avoid actually touching the glass
as this could leave smudges. Clean the glass regularly with a lint free cloth dampened with (soapy)
water.
False activation or bad responses of the optical keys can also be caused by:
● Dirt, grease or dust on the glass.
● Shiny surfaces positioned up to 100 mm (4 inches) in front of the display.
Key lock function
To prevent any erroneous operations due to false optical key activation, a key lock function is
implemented. When the function is enabled (default), the optical keys are automatically locked if no
optical key is activated for 30 seconds.
False optical key activations can cause erroneous operation.
Therefore, it is advised to keep the key lock function enabled.
E490-A-PL
FW_E490-A-PL_M_v0302-03_EN Page 11
The Key lock symbol appears on the display to indicate that the keys are locked or disabled:
PROG SELECT CLEAR
Fig.5: Key lock symbol
To unlock the optical keys, an unlock sequence needs to be performed. Start the unlock sequence
by activating any of the optical keys for one second and then releasing it. The display will now
prompt the operator to activate each optical key in sequence: PROG > SELECT > CLEAR.
When successful, the Key lock symbol disappears and the optical keys can be used to control
the unit. To lock the optical keys again, wait for 30 seconds or push the PROG and CLEAR keys
simultaneously for 3 seconds.
(Temporarily) Disabled optical keys
To prevent unwanted access or operation, the optical keys can be disabled completely. Additionally,
after using the mechanical pushbuttons, the optical keys are automatically disabled for 30 seconds.
When the optical keys are disabled, the Key lock symbol is shown continuously and the display
does not prompt for the unlock sequence. See Section 5.2: Operating the Main Electronics Module
(MEM)[»14] for more information.
4.2.3 BACKLIGHT
The E490 is equipped with a backlight to illuminate the display for improved readability. Depending
on the type of supply and loop mode, the backlight functions as follows:
● When the unit is powered by an external power supply, the backlight is on continuously and its
brightness is set by configuration setting
SETUP
2.5: DISPLAY > BACKLIGHT (BRIGHTNESS)[»20].
● When the unit is only powered by the current loop, the backlight can still be used (see
Section 6.4.4: Current loop mode and backlight brightness[»33]). Its brightness is then fixed at a
reduced intensity and the configuration setting is used to turn the backlight on and off.
4.3 OPERATOR FUNCTIONS
Before operating the unit, check that the symbol is not shown on the display.
Otherwise, unlock the optical keys as described in Section 4.2.2: Optical keys[»10].
4.3.1 FUNCTIONS OF THE KEYS IN OPERATOR MODE
The following functions are available:
PROG-key
This key is used to gain access to SETUP mode, see Section 5: Configuration[»14].
SELECT-key
This key is used to select the displayed information, like actual measured input current
and percentage.
CLEAR-key
This key has no function in operator mode.
E490-A-PL
Page 12 FW_E490-A-PL_M_v0302-03_EN
4.3.2 SELECTING DISPLAYED INFORMATION
By pressing the SELECT-key, all relevant information can be reviewed on the display. When no key
is pressed for 20 seconds, the display will jump back to the main screen. The following image of the
display shows the main screen with the calculated value on the top line and measurement unit on
the bottom line.
PROG SELECT CLEAR
Fig.6: Example of display information
The following table shows the available display information screens, determined by the configuration
settings for Display. If an operator alarm occurs, this will also be shown on the same screen – see
Section 4.5: Operator alarms[»13].
Screen Displayed information Function enabled at
MAIN SCREEN Main process value (engineering units)
SCREEN 1 Percentage value (%)
SETUP
2.2: DISPLAY > PERCENTAGE[»20]
SCREEN 2 Actual loop current (mA)
SETUP
2.1: DISPLAY > CURRENT[»20]
SCREEN 3 Minimum process limit (0%)
SETUP
2.3: DISPLAY > LIMITS[»20]
SCREEN 4 Maximum process limit (100%)
INTERNAL ERROR 1) Internal alarm code
1) If an internal error occurs, an additional screen becomes available to show the internal alarm code.
4.4 DISPLAYED INFORMATION
4.4.1 PROCESS VALUES
Main process value
The main screen shows the calculated process value on the top line with the specified number of
decimals as configured in
SETUP
1: VALUE[»19]. When “-----“ is indicated the calculated value is too
large to be displayed.
The engineering unit and optional time unit are indicated on the bottom line of the display. If there
isn’t enough room available, the display will toggle between unit and time unit.
Percentage value
The process value can also be displayed as a percentage between 0.0% and 100.0%.
In most cases, 0% will correspond with 4mA input current and 100% with 20mA. However, if a
reverse curve is selected in
SETUP
1.7: VALUE > REVERSE[»20] 0% will correspond with 20mA and 100%
with 4mA.
Actual loop current
The input loop current is measured and processed 4 times per second based on the settings of
SETUP
3: SENSOR[»20] and the result is then used to calculate the various process values.
The result is also used to calculate the actual loop current (in mA). This calculation omits any filter,
square root or reverse curve calculations and is always based on the factory calibration.
E490-A-PL
FW_E490-A-PL_M_v0302-03_EN Page 13
Speedometer
A speedometer view of the process value can be shown along the top edge of the display. It
contains 10 segments of 10% each, ranging from 0% to 100% and can be enabled and disabled in
SETUP
2.4: DISPLAY > BARGRAPH[»20].
4.4.2 PROCESS LIMITS
When indication of process limits is enabled in
SETUP
2.3: DISPLAY > LIMITS[»20], the operator can select
two additional screens that show the minimum (0%) and maximum (100%) limit of the main process
value.
4.5 OPERATOR ALARMS
4.5.1 RANGE ERROR
When the input current of the current loop is outside the valid measurement range (e.g. due to a wire
break or a faulty sensor), a range error is raised and the display indicates the status on the bottom
line as follows:
Input current Displayed value Status indication
Below 2.00mA - - - - - NO SIGNAL
2.00mA … 3.75mA 00000 RANGE ERROR
3.75mA … 4.00mA Value at 4mA -
4.00mA … 20.00mA Calculated value -
20.00mA … 22.00mA Value at 20mA -
Above 22.00mA 99999 RANGE ERROR
Note: The current loop input circuit is guaranteed to operate reliably from 3.3mA. Below this current, the shown
values are only an indication and at some point, the circuit will stop working.
4.5.2 INTERNAL ERROR
When an internal error occurs, the alarm flag starts flashing to indicate this.
If the alarm flag shows because of an internal error, the alarm code can be displayed by pushing the
SELECT-key repeatedly until the internal alarm screen is shown.
See Section B: Troubleshooting[»39] for a description of the codes.
Fig.7: Display with alarm flag and internal alarm screen
E490-A-PL
Page 14 FW_E490-A-PL_M_v0302-03_EN
5 CONFIGURATION
5.1 INTRODUCTION
This chapter describes how technicians can use configuration settings to configure the unit for
optimal functionality.
Configuration of the E490-A-PL can be done through:
● SETUP-mode using the optical keys (with cover installed)
● SETUP-mode using the mechanical keys (push buttons) (without cover)
● PC configuration tool using a communication option
5.2 OPERATING THE MAIN ELECTRONICS MODULE (MEM)
Explosion risk: never open the housing when explosive atmosphere is present.
Opening and servicing of the unit may only be carried out by authorized and trained personnel who
have read and understood this manual, particularly Section 2: Safety[»5].
Before opening the enclosure, consult Section 6.2.3: Opening, assembling and closing the unit[»26].
During normal operation, the cover of the unit is installed and all configuration settings can be
reviewed and changed in SETUP-mode using the optical keys. When the cover is removed during
installation and servicing, the optical keys do not function and the Main Electronics Module becomes
available, which offers different possibilities to configure the unit.
3
2
1
Fig.8: Exploded view indicating main components
1. Cover 2. Main Electronics Module (MEM) 3. Body
E490-A-PL
FW_E490-A-PL_M_v0302-03_EN Page 15
5.2.1 CONFIGURING USING PC CONFIGURATION TOOL
Configuration of the E490-A-PL can be done using a PC with our free of charge Remote
Configuration Tool software. Consult Section C: Remote Configuration Tool[»40] for details.
Connection to a PC is made by means of the communication port, located at the back side of the
MEM.
CONFIG
Fig.9: USB connection between MEM and PC
All settings available in the PC Configuration tool correspond with menu items available in SETUP-
mode. Please see Section 5.5: SETUP menu explanations[»19].
5.2.2 MECHANICAL KEYS
A quick and convenient way to configure the E490-A-PL is by means of SETUP-mode and three
mechanical keys (push buttons) at the side of the MEM (available with the cover removed).
PROG CLEAR
SELECT
Fig.10: Control panel pushbuttons
The mechanical keys copy the functionality of the corresponding optical keys at the front side of the
MEM. After operating the mechanical keys, the optical keys are disabled for 30 seconds to avoid
interference and to allow to replace the cover. The Key lock symbol indicates that the optical
keys are temporarily disabled, see Section 4.2.2: Optical keys[»10].
5.2.3 OPTICAL KEYS SWITCH
The optical keys can be disabled to prevent unwanted access or false activation under some
circumstances. The switch can be found at the outside rim of the MEM.
The Key lock symbol is shown on the display when the optical keys are disabled, see
Section 4.2.2: Optical keys[»10]. The mechanical keys always remain active.
E490-A-PL
Page 16 FW_E490-A-PL_M_v0302-03_EN
Fig.11: Disable switch for optical keys
Use this switch to permanently disable the optical keys:
●Enable: move to the right / ON position.
●Disable: move to the left / OFF position.
5.3 CONFIGURING USING SETUP MODE
For an overview of Operating modes, see Section 4.1.1: Operating modes[»9].
Changing settings may influence current operation
In SETUP mode the unit remains fully operational. Make sure the product is not being used for any
application when changing settings.
5.3.1 ENTERING SETUP MODE
1. Check if the Key lock symbol is displayed on the screen. If necessary, unlock the keys by
entering the unlock sequence (see Section 4.2.2: Optical keys[»10]).
2. Press the PROG-key for 7 seconds making sure is continually displayed while pressing.
You may be prompted to enter a password (do so as described in Section 5.3.3: Changing
configuration settings[»17]).
3. The
SETUP
indicator is now activated on the display and the
RUN
indicator is deactivated.
5.3.2 NAVIGATING THE SETUP MENU
The SETUP menu contains several menu groups, which each contain various menu items. Each
menu item has a unique number which is displayed below the
SETUP
indicator at the bottom of the
display. Additionally, each menu item is expressed with a keyword.
The menu number is a combination of two figures separated by a dot:
● the first figure indicates the selected menu group (e.g. 1. TOTAL).
● the second figure indicates the menu item (e.g. 1.1 UNIT).
The following image shows the layout of the menu structure:
1.1
1.2
2.1.
2.1
1.3
2.2
3.1
3.
SELECT
CLEAR
CLEAR
PROG
Fig.12: SETUP menu layout and navigation
E490-A-PL
FW_E490-A-PL_M_v0302-03_EN Page 17
Navigate the SETUP menu with the following functions:
PROG-key
When a menu item is selected (e.g. 1.1), this key is used to start the programming
sequence.
When a menu group is selected (and no function), this key is used to scroll back a
group (e.g. 3. à 2. à 1. à 3. à 2. ...)
SELECT-key
This key is used to select the next menu item in the list (e.g. 1. à 1.1 à 1.2 à 1.3 à
1. ...). When the top of the list is reached, it will wrap around and return to the menu
group selection.
CLEAR-key
This key is used to select the previous menu item in the list (e.g. 1.3 à 1.2 à 1.1 à 1.
à 2. ...). When the bottom the list is reached, it returns to the menu group selection.
When a menu group is selected (and no item), this key is used to scroll to the next
group (e.g. 1. à 2. à 3. à 1. à 2. ...)
5.3.3 CHANGING CONFIGURATION SETTINGS
A menu item either contains a value (a number with optionally a decimal point and sign, e.g.
-123.45), a selection list (e.g. L – m3 - USGAL) or a line of text (e.g. ABCDEFGH). After a menu item
is selected in the SETUP menu, a new value can be programmed by performing the following steps.
During the programming sequence, the
PROG
indicator is flashing on the display.
Step 1: Start the programming sequence:
PROG-key
When a menu item is selected in the SETUP menu, this key is used to start the
programming sequence.
Step 2a: Change a value
SELECT-key
This key is used to increment the selected digit or to select de next position of the
decimal point.
When the entered value is out of range, the increase sign or decrease-sign will
be displayed; the value will be automatically brought within range when confirmed later.
CLEAR-key
This key is used to select the next digit. If a decimal point can be set, this will be
included in the sequence as well (e.g. [decimal point] à digit 1 à digit 2 à digit 3 à
[decimal point].
The selected decimal point is flashing when is can be changed. When no decimal point
is selected, all available decimals will be flashing on the display to indicate this when
the sequence reaches the decimal point.
SELECT CLEAR
SELECT-key + CLEAR-key
The combination of the SELECT-key and CLEAR-key is used to select a negative
value. When a value can also be entered as a negative number, pressing the SELECT-
key and CLEAR-key simultaneously will toggle the ‘–‘ (minus) sign on and off.
Step 2b: Change the selection in a list
SELECT-key
This key is used to select the next item in the list (e.g. L à m³ à USGAL).
At the end of the list, the selection will wrap around to the first selection.
CLEAR-key
This key is used to select the previous item in the list (e.g. USGAL à m³ à L).
At the bottom of the list, the selection will wrap around to the last selection.
E490-A-PL
Page 18 FW_E490-A-PL_M_v0302-03_EN
Step 2c: Change a line of text
SELECT-key
This key is used to scroll though the list of available characters, which is determined by
the selected position on the display. If possible to display, the following characters can
be selected: ", *, –, 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, A, B, C, D, E, F, G, H, I, J, K, L, M, N, O,
P, Q, R, S, T, U, V, W, X, Y, Z.
When a line of text is programmed via the Remote Configuration Software, this will also
be restricted to the character set indicated above but some tweaking on the local
display might be required.
CLEAR-key
This key is used to select the next character. When the end of the line is reached, the
selection will wrap around to the first character (e.g. character 1 à character 2 à
character 3 à character 4 à character 1).
The currently selected character will be flashing; when the selected character
represents a space, it will alternate with an _ (underscore).
● A blinking underscore _ represents a space, not an underscore!
● Press the CLEAR-key for 3 seconds to clear the entire line of text.
● Press the PROG-key for 3 seconds to cancel any changes.
Step 3: Finish the programming sequence
PROG-key
During the programming sequence, this key is used to confirm the new value and
return to SETUP mode. To cancel the operation, either press the PROG-key for 3
seconds or wait for 20 seconds: the programming sequence is cancelled and the
former value is reinstated.
5.3.4 RETURNING TO OPERATOR MODE
When all configuration settings are set correctly, return to OPERATOR mode by pressing the
PROG-key for three seconds, or do not press any key for 2 minutes to return automatically. The
RUN
indicator is now activated on the display and the
SETUP
indicator is deactivated.
5.4 SETUP MENU OVERVIEW
All unit settings can be configured from the control panel. You can also use the Remote
Configuration Software, which can be downloaded from our website or is available from your
supplier (see Section C: Remote Configuration Tool[»40]).
1 VALUE DEFAULT
1.1 UNIT L, NL, mL, m3, am3, nm3, mg, g, Kg, ton, oz, gal, usgal,
igal, lb, bbl, cf, cuft, scf, p, rev, °C, °F, K, %, m, mm, cm,
mtr, inch, ft, sqft, yd, psi, psig, mbar, mbarg, bar, barg,
bara, pa, pag, kpa, kpag, mpa, inhg, inHg, mmHg,
mmH2O, mH2O, inH2O, ph, mA, A, uS, ppm, rpm, no unit,
user
L
1.2 TIME none (----), /sec, /s, /min, /m, /hour, /h, /day, /d, /xxx none
1.3 USER 8 characters - - - - - - - -
1.4 DECIMALS 0, 0.1, 0.02, 0.003, 0.0004 0
1.5 SPAN 0.0001 - 99999 1600
1.6 OFFSET -99999 - 99999 0
1.7 REVERSE on, off off
E490-A-PL
FW_E490-A-PL_M_v0302-03_EN Page 19
2 DISPLAY DEFAULT
2.1 CURRENT on, off off
2.2 PERCENTAGE on, off off
2.3 LIMITS on, off off
2.4 BARGRAPH enable, disable enable
2.5 BACKLIGHT
(BRIGHTNESS)
0%, 20%, 40%, 60%, 80%, 100% 100%
3 SENSOR DEFAULT
3.1 FORMULA interpolation, square root interp.
3.2 FILTER 01 - 99 (01 = off) 01
3.3 CALIB-LOW dflt, calib, set dflt
3.4 CALIB-HIGH dflt, calib, set dflt
3.5 CURRENT MA Currently measured mA value -
4 OTHERS DEFAULT
4.1 MODEL - -
4.2 SOFTWARE VERSION xx.xx.xx -
4.3 SERIAL NUMBER xxxxxxx -
4.4 PASSWORD 0000 - 9999 (0000 = off) 0000
4.5 KEY LOCK enable, disable enable
4.6 TAG NUMBER 0000000 - 9999999 0000000
5.5 SETUP MENU EXPLANATIONS
5.5.1 MENU 1: VALUE
1 VALUE
1.1 UNIT This setting determines the measurement unit for the main process
value. The following can be selected:
L, NL, mL, m3, am3, nm3, mg, g, Kg, ton, oz, gal, usgal, igal, lb, bbl, cf,
cuft, scf, p, rev, °C, °F, K, %, m, mm, cm, mtr, inch, ft, sqft, yd, psi, psig,
mbar, mbarg, bar, barg, bara, pa, pag, kpa, kpag, mpa, inhg, inHg,
mmHg, mmH2O, mH2O, inH2O, ph, mA, A, uS, ppm, rpm, no unit, user
When USER is selected, the user defined measurement unit set at
1.3: VALUE > USER is displayed.
When the measurement unit is altered, span and offset have to be
adapted as well; the calculation is not done automatically!
1.2 TIME This setting is used to select an optional time interval (sec, min, hour or
day) for the main process value. The following can be selected:
none (----), /sec, /s, /min, /m, /hour, /h, /day, /d, /xxx
If USER is selected at 1.1: VALUE > UNIT, the selected time unit overwrites
the last three characters of the user defined unit set at 1.3: VALUE > USER.
1.3 USER This setting is used to enter a user defined measuring unit of up to 8
characters long that will be shown on the bottom line of the display if
USER is selected at 1.1: VALUE > UNIT,
If a time unit is selected at 1.2: VALUE > TIME, the selected time unit
overwrites the last three characters. If /xxx is selected, only the ‘/‘
symbol is displayed.
Section : Changing configuration settings[»18] shows instructions on
changing the characters via the control panel. Alternatively, the
characters can also be programmed via the Remote Configuration Tool.
Please note that the first 2 characters on the left have a reduced
character set as compared to the other 6 characters.
E490-A-PL
Page 20 FW_E490-A-PL_M_v0302-03_EN
1 VALUE
1.4 DECIMALS Determines the number of decimals used for displaying the main
process value.
The number of decimals selected here is also used for 1.5: VALUE > SPAN
and 1.6: VALUE > OFFSET.
1.5 SPAN The span is used to convert the sensor signal to a process value and
represents the difference between the maximum process limit (100%)
and the minimum process limit (0%). The span is entered in the range of
0 to 99999 while taking into account the configured number of decimals
of 1.4: VALUE > DECIMALS.
The accuracy of the measurement system depends on the accuracy of
the entered span and offset. When the accuracy of the main process
value is insufficient, a smaller measurement unit can be selected, or the
number of decimals increased.
1.6 OFFSET The offset is used to set the minimum limit (0%) of the process value.
The offset can be entered in the range of -99999 to 99999 while taking
into account the configured number of decimals of 1.4: VALUE > DECIMALS.
1.7 REVERSE Normally, the input loop current and the process value are directly
proportional. However, in cases where they are inversely proportional,
this direction can be reversed with this setting:
●Off: the displayed value increases with increasing input current.
●On: the displayed value decreases with increasing input current
5.5.2 MENU 2: DISPLAY
2 DISPLAY
2.1 CURRENT When this setting is set to on the actual measured input loop current
(mA) can be reviewed in operator-mode.
2.2 PERCENTAGE When this setting is set to on the process value displayed as a
percentage (%) can be reviewed in operator-mode.
2.3 LIMITS When this setting is set to on the minimum process limit (0%) and
maximum process limit (100%) can be reviewed in operator-mode.
2.4 BARGRAPH The unit has a speedometer/bar graph around the edge of the display
that gives a quick impression of the actual process value. The following
can be selected:
●Enable: the bar graph is switched on.
●Disable: the bar graph is switched off.
2.5 BACKLIGHT
(BRIGHTNESS)
The display is equipped with a backlight with adjustable brightness. This
setting allows the intensity to be adjusted in steps of 20% from off (0%)
to maximum (100%).
When the backlight is only supplied by the current loop, the brightness is
fixed on a reduced intensity, and can only be turned on and off.
5.5.3 MENU 3: SENSOR
3 SENSOR
3.1 FORMULA The E490-A-PL can process the analog signal with two different
formulas:
●Interpolation: the signal is processed in a linear way
Input value (%) = 100% x Iscaled
●Square root: the signal is processed for a quadratic relationship, e.g.
with differential pressure measurement for flow indication
Input value (%) = 100% x √Iscaled
Where Iscaled = measured analog input value, scaled between 0 and 1.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
Fluidwell E490 Le manuel du propriétaire
- Catégorie
- Mesure, test
- Taper
- Le manuel du propriétaire
dans d''autres langues
- English: Fluidwell E490 Owner's manual
Documents connexes
-
Fluidwell F053 Le manuel du propriétaire
-
-
Fluidwell F010 Le manuel du propriétaire
-
-
-
-
-
-
