SIPATEC SW.Ex Manuel utilisateur

Marque
SIPATEC
Modèle
SW.Ex
Taper
Manuel utilisateur
ATEX / IECEx certified for Gases and Dusts
Measurement in Zone 0/20
Direct power supply without zener barrier
Easy plug-in mounting
Quick and safe installation
Junction box Ex e integrated
No variants only one basic unit
Enhanced temperature range -40 … +70 °C
Degree of protection IP66
Switching outputs adjustable
Adjustable hysteresis
Integrated display
Onsite parameterization
LED status indication
Low power input <3 W
Cable length from the switch relay to the sensor up to 100 m
Highly resistant against corrosion by use of high-tech polymer and stainless steel
SW.Ex + IR.Ex
Manual
Assembly and Installation Instructions for safe use of
explosion-proof switching relay SW.Ex with two relay outputs SPDT
and sensor IR.Ex for temperature, humidity, differential pressure, air flow
BA.0002.03.EN
SW.Ex / IR.Ex switching module with relay output
久德電子 TEL：+886-4-23729418 FAX：+886-4-23724011 (40349)台中市西區福人街11號 www.jetec.com.tw
Sicherheitshinweise
Safety Notes
Consignes de Sécurité
Ex-Bereich Sicherer Bereich
Hazardous area Safe area
Zone dangereuse Zone de sécurité
Zone 0,1,2,20,21,22 Zone 1,2,21,22
IR.Ex SW.Ex
Ta (T6) -40…65 °C Ta (T4) : -40 … +70 °C
Ta (T5) -40…80 °C
Ta (T4) -40…115 °C Ui =4,6 V DC Uo ≤ 4,6 DC
Ta (T3-1) -40…125 °C Ii = 107 mA Io ≤ 107 mA
Pi = 428 mW Po ≤ 428 mW
Ci = 1,034 µF Co = 5,3 µF
Li = 0 mH Lo = 0,10 µH
P+/P-
Ex e Klemmen/terminals 3,4,5 / 6,7,8
Ausgang 2 Umschaltrelais
Output 2 relays SPDT
Sortie 2 inverseurs relais
Ex e Klemmen/terminals 1(+), 2(-)
Versorgung 20 ... 28,8
VAC/DC
Supply 50/60 Hz
Alimentation
Installieren Sie gemäß Herstellerangaben und für Sie gültigen Normen und Regeln.
Das Entriegeln des Gerätes oder öffnen des Klemmkastens ist nur im spannungslosen Zustand gestattet.
Beim Einbau des Gerätes ist darauf zu achten, dass die Gehäuseschutzart IP66 nach EN 60529 eingehalten wird.
Dieses Betriebsmittel kann nach Herstellerangaben in der Zone 1, 21 (II 2GD) bzw. Zone 22 (II 3GD) eingesetzt werden.
Der Sensorstromkreis darf in die Zone 0 (II 1G) eingeführt werden. Entspricht der Bezeichnung II 2(1)G.
Die Geräte dürfen nur in Messstoffen eingesetzt werden, gegen welche die prozessberührenden Materialien beständig sind.
Das Gerät ist an den Potenzialausgleich (PA) anzuschließen, dazu steht ein innerer und äußerer Anschluss zu Verfügung.
Das Gerät ist vor mechanische Belastung und UV Licht zu schützen.
Install in accordance with manufacturer's instructions and valid standards and rules.
Unlocking the device or open the terminal box is only permitted with the power off.
When installing the unit, make sure that the housing IP66 degree of protection is maintained in accordance with EN 60529.
This equipment can be used according to manufacturers' instructions in Zone 1, 21 (II 2 GD) and 22. (II 3GD).
The sensor circuit can be introduced into the zone 0 (II 1G). Corresponds to the designation II 2 (1) G.
The device may only be used in such conditions, against which the process-contacting materials are resistant.
The unit must be connected to the potential equalization (PA), an internal and external terminal is available.
The unit must be protected against mechanical impact and UV light.
Installer conformément aux instructions et aux normes et règles en vigueur du fabricant.
Libérer l'appareil ou ouvrir la boîte à bornes ne est autorisée qu'avec l'appareil hors tension.
Lors de l'installation, assurez-vous que le degré de protection IP66 boîtier est maintenu conformément à la norme EN 60529.
Cet équipement peut être utilisé selon les instructions du fabricant dans la zone 1, 21 (II 2 GD) et 22 (II 3GD).
Le circuit de capteur peut être introduit dans la zone 0 (II 1G). Correspond à la désignation II 2 (1) G.
Le dispositif ne peut être utilisé dans de tels liquides, contre lequel les matériaux de traitement contact sont résistants.
L'appareil est connecté à la liaison équipotentielle (PA) pour rejoindre, ceci est une borne interne et externe à votre disposition.
L'appareil doit être protégé contre les chocs mécaniques et la lumière UV.
0
SW.Ex / IR.Ex switching module with relay output
1. General
The manual is included in the delivery and serves to ensure
proper handling and optimum functioning of the device. The
manufacturer is not responsible for this publication nor
guarantee and improper handling of the products described
any liability. For this reason, read the manual before
operation. In addition, the manual is for all personnel who are
involved in the transport, setup, operation, maintenance and
repair to bring in knowledge. This manual may not, without
the prior written consent of the manufacturer used for
competition purposes and will not be passed on to third
parties. Copies for personal use are permitted. This
documentation may contain technical inaccuracies or
typographical errors. The information shall be revised
periodically and are subject to modifications. The
manufacturer reserves the right to modify or alter the product
described at any time.
© Copyright petz industries GmbH & Co. KG
All rights reserved
SYMBOLS
This sign shows
Safety notes.
Safety notes must be followed. Failure to observe personal
injury or property damage may result. The manufacturer
assumes no liability.
SAFTEY NOTES
Installation, electrical connection, maintenance and
commissioning may only be performed by trained
specialist.
Avoid excessive mechanical stress and improper use.
Switch off power when mounting and dismounting
The display loses contrast and brightness in the cold
conditions. Regenerates when the temperature rises
to its original state.
2. Product description
A basic unit SW.Ex and various sensors of the series IR.Ex solve
a variety of measurement tasks. The sensors are available for
multi-functionality, high accuracy and simple assembly.
The following sensors are available:
Temperature
Temperature and humidity, dew point
Differential pressure
Special sensors on request
In addition, allow the button a suburb commissioning and the
LCD display is used as a suburb of measured values. The
integrated terminal box of protection Ex e guarantees a direct
electrical connection in the hazardous area.
Due to the modular concept of separation of electronics and
mounting plate a simple, easy installation and commissioning
is guaranteed.
Options such as different sensor cable for difficult installation
conditions supplement the product portfolio. Calibration of
the measuring chain are made possible by the design of the
device in the easiest way.
MEASUREMENT PRINCIPLE
The physical unit is detected in the series sensors IR.Ex. The
measured value is digitally processed. The transfer to the
switching relay SW.Ex done by an intelligent protocol that
enables easy-to-change sensors and is open for future
sensors.
The robust, interference-free signal from the sensor to
transmitter allows even in harsh industrial environments to
transfer up to 100 m.
In the SW.Ex module, the sensor signal is converted into freely
scalable switching outputs. You can choose upper, lower limit
and hysteresis which can be set by software menu.
久德電子 TEL：+886-4-23729418 FAX：+886-4-23724011 (40349)台中市西區福人街11號 www.jetec.com.tw
SW.Ex / IR.Ex switching module with relay output
3. Technical Data
SW.Ex SWITCHING RELAY
SUPPLY
Voltage
20 – 28,8
V AC/DC
Frequency
50 – 60
Hz
Power consumption
3 / 5
W / VA
OUTPUTS
2 Relays with changeover contact (SPDT), hysteresis adjustable
Potential free
Relay max
30 / 2
V DC / A
Relay min.
5 / 0,1
V DC / A
Hysteresis adjustable
0,5-100
% FS
DISPLAY / BUTTON / LED
LCD, backlight
128 x 64
pixel
Micro push button
> 1 Mio.
cycles
LED red / green
Status indication
HOUSING
High Tech Polymer
halogen-, silicon-, PVC
free
Surface conductivity
< 10^9
Ohm
Corrosion resistance
On- and Offshore
With high salinity
IP protection
IP66
GENERAL
Terminal square
ATEX/IECEx Ex e
0,08 – 2,5
0,25 – 1,5
mm without end sleeve
mm with end sleeve
Cable glands M20x1,5 ATEX/IECEx Ex e
6 - 13
Ø mm
Dimensions H x B x T
175 x 110 x 56
mm
Weight
800
g
MATERIALS
Housing
High Tech Polymer
electrostatically conductive
Front plate, srews
Stainless steel
Seals
EPDM
Cable glands
brass plated
Sensor connection M12
brass plated
APPLICATION
Ambient- and storage temperature
-40 … +70
°C
Humidity, without condensation
0 … 100
%rH
Mountion position
Any, recommended vertical
IR.Ex -P/-V-… DIFFERENTIAL PRESSURE / AIR VOLUME / AIR FLOW
TYPES AND MEASUREMENT RANGE
IR.Ex-P-100
-100 – 100
Pa
IR.Ex-P-250
-250 – 250
Pa
IR.Ex-P-600
-600 – 600
Pa
IR.Ex-P-1000
-1000 – 1000
Pa
IR.Ex-P-2500
-2500 – 2500
Pa
ACCURACY
2,0 / 2,0 / 1,5 / 1,0 / 1,0
% FS
< 0,5
% FS
Long term stability 1.000 h / 25 °C
0,5
%
MTTF (Sensor)
4.611.965
h
SUPPLY EX I
Voltage Ui
4,6
V
Current Ii
0,107
A
Power Pi
0,428
W
Capacitance Ci
1,034
µF
Inductance Li
0
µH
HOUSING
High Tech Polymer
halogene-, silicon-, PVC
free
Surface conductivity
< 10^9
Ohm
Corrosion resistance
On- and Offshore
With high salinity
MATERIALS
Housing
High Tech Polymer
electrostatically conductive
Front plate, Srews
Stainless steel
Seals
EPDM
tube connection
brass plated
久德電子 TEL：+886-4-23729418 FAX：+886-4-23724011 (40349)台中市西區福人街11號 www.jetec.com.tw
SW.Ex / IR.Ex switching module with relay output
IR.Ex -RT / RH-… TEMPERATURE / HUMIDITY (ROOM)
-40 … +125
°C
0 … 100
°C / %rF
Accuracy temperature @.0 … 60 °C
< 0,5
°C
Accuracy temperature @.-40 … 0, @ 60 … 125 °C
< 0,5 °C + 0,03°C/K
°C/K
2,0
% FS
1,0
%
0,5
%
9.312.507
h
4,6
V
0,107
A
0,107
W
0,33
µF
0
µH
Stainless Steel
EPDM
brass plated
-40 … +125
°C
0 … 100
%rH
Any, recommended vertical
IR.Ex -DT / DH-… TEMPERATURE / HUMIDITY (DUCT)
-40 … + 125
°C
-40 … + 125
°C
-40 … + 125
°C
0 … 100
%rH
0 … 100
%rH
0 … 100
%rH
Accuracy temperature @.0 … 60 °C
< 0,5
°C
Accuracy temperature @.-40 … 0, @ 60 … 125 °C
< 0,5 °C + 0,03°C/K
°C/K
2,0
% FS
1,0
%
0,5
%
9.312.507
h
4,6
V
0,107
A
0,428
W
1,034
µF
0
µH
Stainless Steel
Stainless Steel
EPDM
brass nickel plated
-40 … +125
°C
0 … 100
%rH
Any, recommended vertical
CERTIFICATES
SW.Ex ATEX
IECEx
EPS 15 ATEX 1 107 X
IECEx EPS 15.0083 X
II2(1)G Ex eb mb ib [ia Ga] IIC T4 Gb
II2(1)D Ex tb [ia Da] IIIC T130 °C Db
IR.Ex ATEX
IECEx
EPS 15 ATEX 1 107 X
IECEx EPS 15.0083 X
II1/2G Ex ia IIC T6/T5/T4 Ga/Gb
II1/2D Ex ia IIIC T130 °C Da/Db
久德電子 TEL：+886-4-23729418 FAX：+886-4-23724011 (40349)台中市西區福人街11號 www.jetec.com.tw
SW.Ex / IR.Ex switching module with relay output
4. Dimension
SW.Ex IR.Ex-D….(DUCT/KANAL)
56 mm 110 mm 75
45
10
175 mm
Ø 12 mm
200 mm 100 mm 50 mm
IR.Ex-P….(PRESSURE/DRUCK) IR.Ex-R….(ROOM/RAUM)
66 mm
75 mm 95 mm 50 mm 80 mm
2 x Ø 6 mm Ø 12 mm
久德電子 TEL：+886-4-23729418 FAX：+886-4-23724011 (40349)台中市西區福人街11號 www.jetec.com.tw
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

SIPATEC SW.Ex Manuel utilisateur

Marque
SIPATEC
Modèle
SW.Ex
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents