Bartec Pixavi Cam Smartphone Mode d'emploi

Marque: Bartec

Modèle: Pixavi Cam Smartphone

Taper: Mode d'emploi

Quick start guide

Pixavi Phone

Pixavi Thermal

Pixavi Cam

Congratulations on your Pixavi intrinsically safe device.

All you need to get started with Pixavi Phone, Pixavi Cam and

Pixavi Thermal can be found in this quick guide. If you need

further assistance, try the AndroidTM help function, or visit:

www.bartecmobility.com/support-portal

Pixavi Phone ¹

Intrinsically safe smartphone

Pixavi Thermal (²)

Intrinsically safe smartphone with FLIRTM thermal camera

Pixavi Cam (³)

Intrinsicallty safe camera

Introduction Your device

1: 5.5” OLED

2: Power button

3: Volume button (-/+)

4: Programmable button

5: Proximity/Ambient light sensor and status LED

6: Front Camera

7: Earpiece speaker

8: Lanyard mounting slot

9: Magnetic USB connector

10: Microphone

6 7

910

1: Loudspeaker

2: Thermal camera (²)

3: Main camera

4: Flash

5: Microphone

6: Dual SIM/SD tray (¹, ²) or SD tray (³) (below battery pack)

7: Battery pack

8: Battery pack torx T10 fasteners

9: NFC

1: Insert the SIM and/or SD card according to the

SIM/SD-card instructions (separate sheet)

2: Press and hold the Power button to power on the device

Insert the magnetic charger cable in the USB/Charging port

at the bottom of the device. Make sure the orientation of the

cable is as illustrated below.

Do not use any force when inserting the magnetic charging/USB

cable

Charge the device in the non-hazardous area only

For charging the device, use only Bartec approved chargers and

cables. More info in the “Conditions For Use” sections

Getting started

Charging

(¹) Pixavi Phone

(²) Pixavi Thermal

(³) Pixavi Cam

If the device becomes unresponsive or does not boot

successfully, try performing a soft reset. This is done by

pressing and holding the power button down for 10 seconds.

FAQs and technical support can be found here:

www.bartecmobility.com/support-portal

Troubleshooting and Support

Product marking

The programmable button can be conﬁgured to launch an

applications or action on single tap, double tap and long

press.

It’s comes preconﬁgured but can be changed based on your

preferences. Go to Setting -> Programmable Button.

Other options:

Push-to-talk (PTT): Press and hold to talk.

Single tap, duble tap and press and hold will be disabled

when PTT is activated.

SOS-message: Tap the button fast 5 times to send a SOS

message to one or multiple contacts.

Programmable button

WARNING: Do not charge or open battery in hazardous areas!

ATTENTION: Ne pas charger ia batterie dans la zone a risque d'explosion

Pixavi

ThermalClass I, II, III, Division 1

Groups A, B, C, D, E, F, G

Class I, Zone 0, AEX ia IIC T4 Ga,

Ex ia IIC T4 Ga

Zone 20, AEX ia IIICT135˚C Da ;

Ex ia IIICT135˚C Da

CSA 20 ATEX

x xxx X

II 1G Ex ia IICT4 Ga

II 1D Ex ia IIICT 135˚C Da I P6x

I M1 Ex ia I Ma

IECEx CSA 20.xxxxX

S/N X8KYYPTXXXXXX

Type:

17-S13*-1***/********

BARTEC GmbH www.bartec.com

97980 Bad Mergentheim / Germany

Assembled in Norway

Only use battery type: 17-S1Z0-0001

Utiliser uniquement la batterie type: 17-S1Z0-0001

Read user manuel before use

Lire le manuel d'utilisation avent utilisation

FCC ID: XXXXXXXXXXXXXXXX, IC ID:

XXXXXXXXXXXXXXXX

Cell made in China, Assembled in Norway

Pixavi Battery

Mfr: BARTEC GmbH

97980 Bad Mergentheim, DE

Type: 17-S1Z0-0001

Battery info 3.8 V , 3200 mAh , 12.16 Wh

Limited Charge Voltage (4.35 V) Class I, II, III, Division 1

Groups A, B, C, D, E, F, G

Class I, Zone 0, AEX ia IIC T4 Ga,

Ex ia IIC T4 Ga

Zone 20, AEX ia IIICT135˚C Da ;

Ex ia IIICT135˚C Da

CSA 20 ATEX x xxx X

II 1G Ex ia IICT4 Ga

II 1D Ex ia IIICT 135˚C Da I P6x

I M1 Ex ia I Ma

IECEx CSA 20.xxxxX

0044

S/N:

X8K(YY)PB(xxxxxx)

QR-

code

The device is compliant with the EN9650-1 standard.

However, third party music players can exceed the

recommended audio levels, and as such should be used with

caution as prolonged listening to sound at high volumes can

cause permanent damage.

Ex ib parameter

USB Interface

X.X V

X.X A

X.X W

This device complies with Part 15 of the FCC Rules. Operation

is subject to the following two conditions: (1) this device

may not cause harmful interference, and (2) this device must

accept any interference received, including interference that

may cause undesired operation.

Ce produit répond aux exigences de la section 15 de la

réglementation FCC. Son fonctionnement est soumis aux

deux conditions suivantes: (1) cet appareil ne doit pas causer

d’interférences nuisibles et (2) cet appareil doit accepter

toute interférence reçue, y compris les interférences qui

peuvent provoquer un fonctionnement indésirable.

Audio Levels

Special Conditions For Safe Use

FCC/IC

The Pixavi Phone, Pixavi Thermal and Pixavi Cam is a radio

transmitter and receiver. It is designed and manufactured

not to exceed the emission limits for exposure to radio

frequency (RF) energy set by the Federal Communications

Commission (FCC) of the U.S. Government, Industry Canada

of the Canadian Government (IC), and recommended by The

Council of the European Union. The exposure standard for

wireless devices employs a unit of measurement known as

the Speciﬁc Absorption Rate, or SAR. The SAR limit set by

the FCC/IC is 1.6W/kg. The SAR limit recommended by The

Council of the European Union is 2.0W/kg. Tests for SAR are

conducted using standard operating positions speciﬁed by

the FCC/IC with the device transmitting at its highest certi-

ﬁed power level in all tested frequency bands.

For body worn operation, the Pixavi Phone, Pixavi Thermal

and Pixavi Cam devices has been tested and meets the FCC/

IC exposure guidelines when used with an accessory that

contains no metal and that positions the device a minimum

of 10 mm from the body. Such a device can i.e. be BARTEC

PIXAVI wrist cradle or BARTEC PIXAVI belt clip.

The highest SAR value measured for the Pixavi Phone, Pixavi

Thermal and Pixavi Cam is:

Head SAR: 0.626 (W/kg)

Body SAR: 1.202 (W/kg)

Text must be approved and tested during FCC cert

Text must be approved during FCC cert

Speciﬁc Absorption Rate Data

FCC

Any Changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

-Consult the dealer or an experienced radio/TV technician for help.

This Pixavi Cam meets the government's requirements for exposure to radio

waves. The guidelines are based on standards that were developed by independent

scientific organizations through periodic and thorough evaluation of scientific studies.

Thestandards include a substantial safety margin designed to assure the safety of all

persons regardless of age or health.

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is

subject to the following two conditions: (1) This device may not cause interference, and (2)

This device must accept any interference, including interference that may cause undesired

operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils

radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le

brouillage est susceptible d'en compromettre le fonctionnement

The ambient temperature range of the device is -20°C to +

60°C. The device shall be protected from contamination by

liquid and dust; this is normally achieved by the operator

carrying the device on their person. The USB port may be

used for charging the equipment when in the non-hazardous

area only.

For charging the device, use only Bartec approved chargers:

Charger with EU plug: G7-S0Z0-0001

Charger with UK plug: G7-S0Z0-0002

Charger with US plug: G7-S0Z0-0003

Charger with AU plug: G7-S0Z0-0004

Charging dock: G7-S0Z0-0007

Vehicle charging dock: G7-S0Z0-0008

For connection to computers and car chargers, use only

Bartec approved charging cable:

USB Safe Box cable G7-S0Z0-0006

Conditions For Use (ATEX & IECEx)

The ambient temperature range of the device is -20°C to +

60°C. The device shall be protected from contamination by

liquid and dust; this is normally achieved by the operator

carrying the device on their person. The USB port may be

used for charging the equipment when in the non-hazardous

area only.

For charging the device, use only Bartec approved chargers:

Charger with EU plug: G7-S0Z0-0001

Charger with UK plug: G7-S0Z0-0002

Charger with US plug: G7-S0Z0-0003

Charger with AU plug: G7-S0Z0-0004

Charging dock: G7-S0Z0-0007

Vehicle charging dock: G7-S0Z0-0008

For connection to computers and car chargers, use only

Bartec approved charging cable:

USB Safe Box cable G7-S0Z0-0006

Android is a trademark of Google LLC.

Conditions For Use (CSA)

Legal

Bartec Pixavi Cam Smartphone Mode d'emploi

Marque: Bartec

Modèle: Pixavi Cam Smartphone

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Bartec Pixavi Cam Smartphone User guide

Bartec Pixavi Cam Smartphone Mode d'emploi

Bartec Pixavi Cam Smartphone Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents