Asus XT12 Mode d'emploi

Marque: Asus

Modèle: XT12

Taper: Mode d'emploi

ASUS ZenWiFi Pro XT12

AX11000 Tri Band Router

Model: XT12

Quick

Start Guide

Plug the adapter into the DCIN port, and press the power switch.

The power LED will light up when your hardware is ready.

Hardware Explanations

Button and Port Explanations

2.5G / 1G WAN port

Connect your optical modem to this

port with a network cable.

Before Setup

ASUS Router App

AiMesh Setup Steps

Troubleshooting

Find two ZenWiFi Pro XT12, and power both on.

Use a network cable to connect your optical modem to the WAN port of either ZenWiFi Pro

XT12. This ZenWiFi Pro XT12 will be the AiMesh router, and the other ZenWiFi Pro XT12 will

be the AiMesh node.

The LEDs turn solid blue to indicate that ZenWiFi Pro XT12 is ready for setup.

Preparing to set up an AiMesh WiFi system

AiMesh Setup Steps

AiMesh routerAiMesh node

Download free ASUS Router APP to set up

and manage your router(s).

AiMesh routerAiMesh node

1 meter

apart

Prepare

Place your AiMesh router and node(s) in the same room and at

least 1 meter apart during the setup process.

AiMesh node

Keep your AiMesh node powered on and standby for AiMesh

system settings.

Enable Bluetooth on your phone. Launch ASUS Router APP, and then follow the on-screen in-

structions to ﬁnish the AiMesh setup.

Enabling Bluetooth Launching ASUS Router APP

03 04

If your AiMesh router cannot ﬁnd any AiMesh node nearby or

synchronization fails, please check the following and try again.

Move your AiMesh node closer to the AiMesh router ideally. Ensure that it is

within 3 meters.

Your AiMesh node is powered on.

DC Power adapter DC Output: +19V with max 2.37A current

+19.5V with max 2.31A current

Operating Temperature 0~40oCStorage Temperature 0~70oC

Operating Humidity 50~90% Storage Humidity 20~90%

Specications:

LAN ports 1-2

WPS button

Reset button

Power switch

DCIN port

2.5G / 1G LAN port

Connect your PC to a 2.5G / 1G LAN

port with a network cable.

2.5G / 1G WAN port

2.5G / 1G LAN port

LAN ports 1-2

Connect your PC to a LAN port with

a network cable.

Relocation

FAQ

THE BEST PERFORMANCE

FREQUENTLY ASKED QUESTIONS

Locate the AiMesh router and node at the best place.

NOTES: To minimize interference, keep the routers away from devices like cordless phones, Bluetooth

devices and microwave ovens.

We recommend that you place the routers in an open or spacious location.

Solid white: Good signal

Solid yellow: Weak signal

Solid red: No signal

ZenWiFi Pro XT12 LED indications

ASUS Recycling/Takeback Services

ASUS recycling and takeback programs come from our commitment to the highest standards for protecting our

environment. We believe in providing solutions for you to be able to responsibly recycle our products, batteries,

other components, as well as the packaging materials. Please go to http://csr.asus.com/english/Takeback.htm for the

detailed recycling information in dierent regions.

REACH

Complying with the REACH (Registration, Evaluation, Authorisation, and Restriction of Chemicals) regulatory

framework, we published the chemical substances in our products at ASUS REACH website at http://csr.asus.com/

english/REACH.htm

Federal Communications Commission Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

• This device may not cause harmful interference.

• This device must accept any interference received, including interference that may cause undesired operation.

FCC regulations restrict the operation of this device to indoor use only.

This device cannot operate as a subordinate between separate buildings or structures.

This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of

the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

WARNING! Any changes or modications not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

Prohibition of Co-location

This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or

transmitter.

IMPORTANT NOTE:

Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an

uncontrolled environment. End users must follow the specic operating instructions for satisfying RF exposure

compliance. To maintain compliance with FCC exposure compliance requirement, please follow operation instruction

as documented in this manual.

WARNING! This equipment must be installed and operated in accordance with provided instructions and the

antenna(s) used for this transmitter must be installed to provide a separation distance of at least 62 cm from

all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.

Compliance Statement of Innovation, Science and Economic Development Canada (ISED)

This device complies with Innovation, Science and Economic Development Canada licence exempt RSS standard(s).

Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device

must accept any interference, including interference that may cause undesired operation of the device.

Operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-

channel mobile satellite systems.

CAN ICES-003(B)/NMB-003(B)

Radio Frequency (RF) Exposure Information

The radiated output power of the ASUS Wireless Device is below the Innovation, Science and Economic Development

Canada radio frequency exposure limits. The ASUS Wireless Device should be used in such a manner such that the

potential for human contact during normal operation is minimized.

This equipment should be installed and operated with a minimum distance of 62 cm between the radiator any part of

your body.

This device has been certied for use in Canada. Status of the listing in the Innovation, Science and Economic

Development Canada’s REL (Radio Equipment List) can be found at the following web address:

http://www.ic.gc.ca/eic/site/ceb-bhst.nsf/eng/h_tt00020.html

Additional Canadian information on RF exposure also can be found at the following web:

https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08792.html

Déclaration de conformité de Innovation, Sciences et Développement économique Canada (ISED)

Le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables

aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne

doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,

même si le brouillage est susceptible d’en compromettre le fonctionnement.

La bande 5150 – 5250 MHz est réservée uniquement pour une utilisation à l’intérieur an de réduire les risques de

brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux.

CAN ICES-003(B)/NMB-003(B)

Informations concernant l’exposition aux fréquences radio (RF)

La puissance de sortie émise par cet appareil sans l est inférieure à la limite d'exposition aux fréquences radio

d'Innovation, Sciences et Développement économique du Canada (ISED). Utilisez l'appareil sans l de façon à

minimiser les contacts humains lors d'un fonctionnement normal.

Cet équipement doit être installé et utilisé avec un minimum de 62 cm de distance entre la source de rayonnement et

votre corps.

L'utilisation de cet appareil est autorisée au Canada. Pour consulter l'entrée correspondant à l'appareil dans la liste

d'équipement radio (REL - Radio Equipment List) d'Innovation, Sciences et Développement économique du Canada,

rendez-vous sur :

http://www.ic.gc.ca/eic/site/ceb-bhst.nsf/eng/h_tt00020.html

Pour des informations supplémentaires concernant l'exposition aux fréquences radio au Canada, rendez-vous sur :

https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08792.html

For product available in the US/Canada market, only channel 1~11 can be operated. Selection of other channels is not

possible.

Pour les produits disponibles aux États-Unis et au Canada, seuls les canaux 1 à 11 peuvent être utilisés. La sélection

d’autres canaux n’est pas possible.

This device is restricted for indoor use only.

Cet appareil convient uniquement à un usage intérieur.

Safety Notices

• Use this product in environments with ambient temperatures between 0°C(32°F) and 40°C(104°F).

• Refer to the rating label on the bottom of your product and ensure your power adapter complies with this rating.

• DO NOT place on uneven or unstable work surfaces. Seek servicing if the casing has been damaged.

• DO NOT place or drop objects on top and do not shove any foreign objects into the product.

• DO NOT expose to or use near liquids, rain, or moisture. DO NOT use the modem during electrical storms.

• DO NOT cover the vents on the product to prevent the system from getting overheated.

• DO NOT use damaged power cords, accessories, or other peripherals.

• If the Adapter is broken, do not try to x it by yourself. Contact a qualied service technician or your retailer.

• To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the

system.

• Utilisez ce produit dans un environnement dont la température ambiante est comprise entre 0˚C (32°F) et 40˚C

(104°F).

• Référez-vous à l'étiquette située au dessous du produit pour vérier que l'adaptateur secteur répond aux exigences

de tension.

• NE PAS placer sur une surface irrégulière ou instable. Contactez le service après-vente si le châssis a été endommagé.

• NE PAS placer, faire tomber ou insérer d'objets sur/dans le produit.

• NE PAS exposer l'appareil à la pluie ou à l'humidité, tenez-le à distance des liquides. NE PAS utiliser le modem lors

d'un orage.

• NE PAS bloquer les ouvertures destinées à la ventilation du système pour éviter que celui-ci ne surchaue.

• NE PAS utiliser de cordons d'alimentation, d'accessoires ou autres périphériques endommagés.

• Si l'adaptateur est endommagé, n'essayez pas de le réparer vous-même. Contactez un technicien électrique qualié

ou votre revendeur.

• Pour éviter tout risque de choc électrique, débranchez le câble d'alimentation de la prise électrique avant de

toucher au système.

Manufacturer ASUSTeK Computer Inc.

Tel. No.: +886-2-2894-3447

Address: 1F., No. 15, Lide Rd., Beitou Dist., Taipei City 112, Taiwan

Authorised

representative in

Europe

ASUS Computer GmbH

Address: HARKORT STR. 21-23, 40880 RATINGEN, GERMANY

Authorised

distributors in Turkey BOGAZICI BILGISAYAR TICARET VE SANAYI A.S.

Tel./FAX No.: +90 212 331 10 00 / +90 212 332 28 90

Address: ESENTEPE MAH. BUYUKDERE CAD. ERCAN HAN B BLOK NO.121 SISLI, ISTANBUL 34394

CIZGI Elektronik San. Tic. Ltd. Sti.

Tel./FAX No.: +90 212 356 70 70 / +90 212 356 70 69

Address: GURSEL MAH. AKMAN SK.47B 1 KAGITHANE/ISTANBUL

KOYUNCU ELEKTRONiK BiLGi iSLEM SiST. SAN. VE DIS TIC. A.S.

Tel. No.: +90 216 5288888

Address: EMEK MAH.ORDU CAD. NO:18, SARIGAZi, SANCAKTEPE ISTANBUL

ENDEKS BİLİŞİM SAN VE DIŞ TİC LTD ŞTİ

Tel./FAX No.: +90 216 523 35 70 / +90 216 523 35 71

Address: NECIP FAZIL BULVARI, KEYAP CARSI SITESI, G1 BLOK, NO:115 Y.DUDULLU, UMRANIYE,

ISTANBUL

PENTA TEKNOLOJI URUNLERI DAGITIM TICARET A.S

Tel./FAX No.: +90 216 528 0000

Address: ORGANIZE SANAYI BOLGESI NATO YOLU 4.CADDE NO:1 UMRANIYE, ISTANBUL 34775

Q1:

Does the AiMesh router support Access Point mode?

A: Yes. You can choose to set the AiMesh router as router mode or access

point mode. Please go to web GUI (http://router.asus.com), and go to the page

Administration > Operation Mode.

Could I setup wired connection between AiMesh routers (Ethernet backhaul)?

Q2:

A: Yes. AiMesh system supports both wireless and wired connection between AiMesh router and node to

maximize throughput and stability. AiMesh analyzes the wireless signal strength for each frequency band

available, and then determines automatically whether a wireless or wired connection is best to serve as the

inter-router connection backbone.

Follow the setup steps to establish a connection between the AiMesh router and node via WiFi ﬁrst.

Place the node in the ideal locations for best coverage. Run an Ethernet cable from the LAN port of the

AiMesh router to the WAN port of AiMesh node.

AiMesh system will auto-select the best path for data transmission, whether wired or wireless.

Modem

LAN-WAN

Asus XT12 Mode d'emploi

Marque: Asus

Modèle: XT12

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Asus XT12 User guide

Asus XT12 Mode d'emploi

Asus XT12 Mode d'emploi

dans d''autres langues

Documents connexes