VTech CD1153 Manuel utilisateur

Catégorie
Téléphones
Taper
Manuel utilisateur
Go to www.vtechphones.com (US)
to register your product for enhanced warranty
support and latest VTech product news.
Go to phones.vtechcanada.com (Canada) for
latest VTech product news.
CD1153
Speakerphone with
caller ID/ call waiting
Scan the QR code for
support information
US CA
Abridged User’s
manual
Important safety information
When using your telephone equipment, basic safety precautions should always
be followed to reduce the risk of fire, electric shock and injury, including the
following:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product.
3. Unplug this product from the wall outlet before cleaning. Do not use liquid
or aerosol cleaners. Use a damp cloth for cleaning.
4. CAUTION: Do not install the telephone base at a height above 2 meters.
5. Do not use this product near water such as near a bath tub, wash bowl,
kitchen sink, laundry tub or a swimming pool, or in a wet basement or
shower.
6. Do not place this product on an unstable table, shelf, stand or other unstable
surfaces.
7. Avoid placing the telephone system in places with extreme temperature,
direct sunlight, or other electrical devices. Protect your phone from moisture,
dust, corrosive liquids and fumes.
8. Slots and openings in the back or bottom of the telephone base and handset
are provided for ventilation. To protect them from overheating, these
openings must not be blocked by placing the product on a soft surface such
as a bed, sofa or rug. This product should never be placed near or over a
radiator or heat register. This product should not be placed in any area where
proper ventilation is not provided.
9. This product should be operated only from the type of power source
indicated on the marking label. If you are not sure of the type of power
supply in your home or office, consult your dealer or local power company.
10. Do not allow anything to rest on the power cord. Do not install this product
where the cord may be walked on.
11. Never push objects of any kind into this product through the slots in the
telephone base or handset because they may touch dangerous voltage
points or create a short circuit. Never spill liquid of any kind on the product.
12. To reduce the risk of electric shock, do not disassemble this product, but
take it to an authorized service facility. Opening or removing parts of the
telephone base or handset other than specified access doors may expose
you to dangerous voltages or other risks. Incorrect reassembling can cause
electric shock when the product is subsequently used.
13. Do not overload wall outlets and extension cords.
14. Unplug this product from the wall outlet and refer servicing to an authorized
service facility under the following conditions:
When the power supply cord or plug is damaged or frayed.
If liquid has been spilled onto the product.
If the product has been exposed to rain or water.
If the product does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the operation
instructions. Improper adjustment of other controls may result in damage
and often requires extensive work by an authorized technician to restore
the product to normal operation.
If the product has been dropped and the telephone base and/ or
handset has been damaged.
If the product exhibits a distinct change in performance.
15. Avoid using a telephone (other than cordless) during an electrical storm.
There is a remote risk of electric shock from lightning.
16. Do not use the telephone to report a gas leak in the vicinity of the leak.
Under certain circumstances, a spark may be created when the adapter is
plugged into the power outlet, or when the handset is replaced in its cradle.
This is a common event associated with the closing of any electrical circuit.
The user should not plug the phone into a power outlet, and should not put
a charged handset into the cradle, if the phone is located in an environment
containing concentrations of flammable or flame-supporting gases, unless
there is adequate ventilation. A spark in such an environment could create a
fire or explosion. Such environments might include: medical use of oxygen
without adequate ventilation; industrial gases (cleaning solvents; gasoline
vapors; etc.); a leak of natural gas; etc.
17. Only put the handset of your telephone next to your ear when it is in normal
talk mode.
18. The power adapter is intended to be correctly oriented in a vertical or floor
mount position. The prongs are not designed to hold the plug in place if it is
plugged into a ceiling, under-the-table or cabinet outlet.
19. For pluggable equipment, the socket-outlet shall be installed near the
equipment and shall be easily accessible.
20. Use only the adapter included with this product. Incorrect adapter polarity or
voltage can seriously damage the product.
21. The applied nameplate is located at the bottom or near of the product.
SAVE THESE INSTRUCTIONS
What’s in the box
Your package contains:
Telephone base with mounting bracket and directory card
attached;
Handset;
Coiled handset cord;
Telephone line cord; and
Abridged User’s manual.
Basic set up & operate
Install battery
This telephone requires four alkaline AA batteries (not
included). Always use the same brand and type of
batteries. Do not mix old and new batteries to prevent
battery leakage. When there is no battery installed or
the power of the installed batteries is low, this telephone
will work only to make or answer calls with the handset.
1. Press down and pull to open.
2. Insert 4 AA alkaline batteries.
3. Close and snap the battery compartment cover into
place.
CAUTION
Always unplug the telephone line cord before isntalling new
batteries.
Install telephone base
1.
Plug!
Plug!
If you have DSL high-speed Internet service, a DSL
filter (not included) is required. The DSL filter must be
plugged into the telephone wall jack.
2.
Plug!
Plug!
Set date and time
1. Press MENU/SELECT repeatedly until the screen
displays:-
DATE/TIME
12:00AM
1-01
2. Use the dial pad keys (0-9) to change the blinking
digit.
Press q or p to the previous or next digit.
Press # (pound key) to select between AM or PM.
3. Press MENU/SELECT to save the new settings and
move to the next option.
Set ringer volume
Slide the ringer
switch to adjust
ringer volume.
appears on the
screen means the
ringer is off.
(RINGER OFF-LO-
HI) design
Slide the ringer
switch to select your
preferred ringer
volume.
Set contrast
Adjust the screen brightness to a comfotable level, from
1 (light) to 4 (dark).
1. Press MENU/SELECT repeatedly until the screen
displays:
CONTRAST
2
2. Press qor p until the screen displays the contrast
level you prefer.
3. Press MENU/SELECT to save the setting.
Set home area code
A home area code must be programmed to use the
display dial feature.
1. Press MENU/SELECT repeatedly until the screen
displays:
HOME AREA CODE
HAC-___
2. Use the dial pad keys (0-9) to enter the home area
code.
Press p to move to the next digit.
Press q to backspace.
Press DELETE to delete a digit.
3. Press MENU/SELECT to save the setting.
Set local area code
1. Press MENU/SELECT repeatedly until the screen
displays:
LOCL AREA CODE
LAC-___
2. Use the dial pad keys (0-9) to enter the home area
code.
Press p to move to the next digit.
Press q to backspace.
Press DELETE to delete a digit.
3. Press MENU/SELECT to save the setting.
4. Repeat step 2 - 3 to set more local area codes.
Set directory
This telephone has a directory where you can store up to
25 telephone numbers and names. Numbers can be up
to 24 digits long and names can be up to 15 characters.
To add a directory entry
1. Press pqor pSTORE flashes → MENU/SELECT.
2. Enter the telephone numberMENU/SELECT.
3. Enter the name → MENU/SELECT.
To review and dial a directory entry
1. Press p.
2. Press qor p until REVIEW flashes.
3. Press MENU/SELECTqor pto scroll through the
directory, then lift the handset or press SPEAKER.
To delete a directory entry
1. Press p.
2. Press qor p until REVIEW flashes.
3. Press MENU/SELECTqor pto scroll through the
directory, then press DELETEMENU/SELECT.
Speed dial
There are 14 speed dial locations (7 upper and 7 lower).
To access an upper location, press a speed dial key.
To access a lower location, press LOWER, then press a
speed dial key.
To assign a speed dial entry
1. Press a speed dial location, or press LOWER, then
the desired speed dial location → press MENU/
SELECT.
2. Enter the telephone number → press MENU/SELECT.
To dial a speed dial entry
1. Lift the handset or press SPEAKER.
2. Press the desired speed dial location, or press
LOWER, then the desired speed dial location.
To delete a speed dial entry
Press the desired speed dial location, or press LOWER,
then the desired speed dial location → Press DELETE
MENU/SELECT.
Caller ID
To review the call history
1. Press q to enter the call history.
2. Press qor p to scroll through the caller ID entries.
3. Press CANCEL to exit and return to idle mode.
To dial a caller ID entry
1. Press q to enter the call history.
2. Press q or p to scroll through the caller ID entries.
3. Lift the handset or press SPEAKER to call.
To delete a caller ID entry
1. Press q to enter the call history.
2. Press q or p to scoll through the caller ID entries →
press DELETE → press MENU/ SELECT.
To delete all caller ID entries
When the telephone is not in use:
1. Press and hold DELETE
2. Press MENU/SELECT.
Disclaimer and Limtation of Liability
VTech Communications, Inc. and its suppliers assume no responsibility for any
damage or loss resulting from the use of this user’s manual.
VTech Communications, Inc. and its suppliers assume no responsibility for any
loss or claims by third parties that may arise through the use of this product.
Company: VTech Communications, Inc.
Address: 9020 SW Washington, Square Road - Ste 555 Tigard, OR 97223, United
States
Phone: 1 (800) 595-9511 in the U.S. or 1 (800) 267-7377 in Canada
Technical specifications
REN 0.6A
Batteries 4 AA alkaline batteries
Operating
temperature
32°F - 122°F
0°C - 50°C
Specifications are subject to change without notice.
© 2023 VTech Communications, Inc.
All rights reserved. 01/23. CD1153_ACIB_V10.0
Missed (new) caller indicator
If you do not want to review the missed calls one by one
and you want to keep them in the caller ID log, you can
press and hold CANCEL on the telephone for 4 seconds
when the telephone is not in use.
Wall mount installation (optional)
1
Slide! Slide!
2
Press to release! Press to secure!
Flip over!
3Plug!
Wrap!
Plug!
Align
If you have DSL high-speed Internet service, a DSL filter (not
included) is required. The DSL filter must be plugged into the
telephone wall jack.
Telephone overview
a
b
c
d
e
f
g
h
i
1 Flashes when there is an incoming call.
2CANCEL Press to return to idle
mode.
Press and hold for 4
seconds when the
telephone is not in use
to erase the missed calls
indicator.
q / CALL LOG Review call history records.
Scroll through options
when in the feature menu.
p/ DIRECTORY Enter the directory. Scroll
through options when in
the feature menu.
MENU/SELECT Display the menu.
Save the setting and
advance to the next
feature setting.
DELETE Press to delete the
displayed entry.
Press and hold to remove
all call history entries
when in idel mode.
3 Speed dial
locations Press to save or dial
numbers in speed dial
locations.
LOWER Press to enter lower
locations of speed dial
keys.
4REDIAL/PAUSE Redial the last number
dialed.
5FLASH During a call, press to
receive an incoming call
if you subscribe to the
call waiting service from
your telephone service
provider.
6VOL+ Increase the
speakerphone or handset
listening volume.
7VOL- Decrease the
speakerphone or handset
listening volume.
8 SPEAKER Make or answer a call
using speakerphone.
9MUTE Mute the handset
or speakerphone
microphone.
Product care | Need help?
Taking care of your telephone
Your cordless telephone contains sophisitcared
electronic parts, so it must be treated with care.
Avoid rough treatment
Place the handset down gently. Save the original
packing materials to protect your telephone if you ever
need to ship it.
Avoid water
Your telephone can be damaged if it gets wet. Do not
use the handset outdoors in the rain, or handle it with
wet hands. Do not install the telephone base near a sink,
bathtub or shower.
Electrical storms
Electrical storms can sometimes cause power surges
harmful to electronic equipment. For your own safety,
take caution when using electrical appliances during
storms.
Cleaning your telephone
Your telephone has a durable plastic casing that should
retain its luster for many years. Clean it only with a dry
non-abrasive cloth. Do not use dampened cloth or
cleaning solvents of any kind. For operations and guides
to help you using your telephone.
For operations and guides to help you using your
telephone, and for the latest information and supports,
go and check the online help topics and online FAQs.
Use your smartphone or mobile device to access our
online help.
• Go to https://help.vtechphones.com/cd1153 (US); OR
https://phones.vtechcanada.com/en/support/general/
manuals?model=cd1153 (Canada)
• Scan the QR code on the right. Launch the camera app
or QR code scanner app on your smartphone or tablet.
Hold the device’s camera up to the QR code and
frame it. Tap the notification to trigger the redirection
of the online help.
- If the QR code is not clearly displayed, adjust
your camera’s focus by moving your device
closer or further away until it is clear.
You can also call our Customer Support at 1
(800) 595-9511 [in US] or 1 (800) 267-7377 [in
Canada] for help.
Limited warranty
What does this limited warranty cover?
The manufacturer of this VTech Product warrants to the holder of a
valid proof of purchase (“Consumer” or “you”) that the Product and
all accessories provided in the sales package (“Product”) are free from
defects in material and workmanship, pursuant to the following terms
and conditions, when installed and used normally and in accordance
with the Product operating instructions. This limited warranty extends
only to the Consumer for Products purchased and used in the United
States of America and Canada.
What will VTech do if the Product is not free from defects in materials
and workmanship during the limited warranty period (“Materially
Defective Product”)?
During the limited warranty period, VTech’s authorized service
representative will replace at VTech’s option, without charge, a Materially
Defective Product. If we choose to replace the Product, we may replace
it with a new or refurbished Product of the same or similar design. We
will retain defective parts, modules, or equipment. Replacement of the
Product, at VTech’s option, is your exclusive remedy. VTech will return
the replacement Products to you in working condition. You should
expect the replacement to take approximately 30 days.
How long is the limited warranty period?
The limited warranty period for the Product extends for ONE (1) YEAR
from the date of purchase. If VTech replaces a Materially Defective
Product under the terms of this limited warranty, this limited warranty
also applies to the replacement Product for a period of either (a) 90
days from the date the replacement Product is shipped to you or (b) the
time remaining on the original one-year warranty; whichever is longer.
What is not covered by this limited warranty?
This limited warranty does not cover:
1. Product that has been subjected to misuse, accident, shipping or
other physical damage, improper installation, abnormal operation
or handling, neglect, inundation, fire, water or other liquid
intrusion;
2. Product that has been damaged due to repair, alteration or
modification by anyone other than an authorized service
representative of VTech;
3. Product to the extent that the problem experienced is caused by
signal conditions, network reliability, or cable or antenna systems;
4. Product to the extent that the problem is caused by use with non-
VTech accessories;
5. Product whose warranty/quality stickers, product serial number
plates or electronic serial numbers have been removed, altered
or rendered illegible;
6. Product purchased, used, serviced, or shipped for repair from
outside the United States of America or Canada, or used for
commercial or institutional purposes (including but not limited to
Products used for rental purposes);
7. Product returned without a valid proof of purchase (see item 2
below); or
8. Charges for installation or set up, adjustment of customer controls,
and installation or repair of systems outside the unit.
How do you get warranty service?
To obtain warranty service in the USA, please visit our website at www.
vtechphones.com or call 1 (800) 595-9511. In Canada, go to phones.
vtechcanada.com or call 1 (800) 267-7377.
NOTE: Before calling for service, please review the user’s manual - a
check of the Product’s controls and features may save you a service call.
Except as provided by applicable law, you assume the risk of loss or
damage during transit and transportation and are responsible for
delivery or handling charges incurred in the transport of the Product(s)
to the service location. VTech will return replaced Product under this
limited warranty. Transportation, delivery or handling charges are
prepaid. VTech assumes no risk for damage or loss of the Product in
transit. If the Product failure is not covered by this limited warranty, or
proof of purchase does not meet the terms of this limited warranty,
VTech will notify you and will request that you authorize the cost of
replacement prior to any further replacement activity. You must pay for
the cost of replacement and return shipping costs for the replacement
of Products that are not covered by this limited warranty.
What must you return with the Product to get warranty service?
1. Return the entire original package and contents including the
Product to the VTech service location along with a description of
the malfunction or difficulty; and
2. Include a “valid proof of purchase” (sales receipt) identifying the
Product purchased (Product model) and the date of purchase or
receipt; and
3. Provide your name, complete and correct mailing address, and
telephone number.
Other limitations
This warranty is the complete and exclusive agreement between you
and VTech. It supersedes all other written or oral communications
related to this Product. VTech provides no other warranties for this
Product. The warranty exclusively describes all of VTech’s responsibilities
regarding the Product. There are no other express warranties. No one
is authorized to make modifications to this limited warranty and you
should not rely on any such modification.
State/Provincial Law Rights: This warranty gives you specific legal rights,
and you may also have other rights, which vary from state to state or
province to province.
Limitations: Implied warranties, including those of fitness for a particular
purpose and merchantability (an unwritten warranty that the Product is
fit for ordinary use) are limited to one year from the date of purchase.
Some states/provinces do not allow limitations on how long an implied
warranty lasts, so the above limitation may not apply to you. In no event
shall VTech be liable for any indirect, special, incidental, consequential,
or similar damages (including, but not limited to lost profits or revenue,
inability to use the Product or other associated equipment, the cost of
substitute equipment, and claims by third parties) resulting from the
use of this Product. Some states/provinces do not allow the exclusion
or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
Please retain your original sales receipt as proof of purchase.
For C-UL Compliance only
Measures de sécurité importantes
Afin de réduire les risques d’incendie, de blessures corporelles ou
d’électrocution, suivez toujours ces mesures préventives de base lorsque vous
utilisez votre téléphone :
1. Lisez et comprenez bien toutes les instructions.
2. Observez toutes les instructions et mises en garde inscrites sur l’appareil.
3. Débranchez ce téléphone de la prise murale avant de le nettoyer. N’utilisez
pas de nettoyeurs liquides ni en aérosol. N’utilisez qu’un chiffon doux et
légèrement humecté.
4. ATTENTION: Ne pas installer le socle téléphonique à une hauteur supérieure
à 2 mètres.
5. N’utilisez pas ce produit près de l’eau, tel que près d’un bain, d’un lavabo,
d’un évier de cuisine, d’un bac de lavage ou d’une piscine, ou dans un sous-
sol humide ou sous la douche.
6. Ne déposez pas ce téléphone sur un chariot, support ou table chancelants.
L’appareil pourrait tomber et être sérieusement endommagé.
7. Évitez d’installer le système téléphonique dans les endroits soumis à une
température extrême, à la lumière directe du soleil ou à proximité immédiate
d’autres appareils électriques ou électroniques. Protégez votre téléphone
contre les sources d’humidité, la poussière, les vapeurs et les liquides corrosifs.
8. Le boîtier de l’appareil est doté de fentes et d’ouvertures d’aération situées
à l’arrière ou en dessous. Afin d’empêcher la surchauffe, ces ouvertures ne
doivent pas être obstruées en plaçant l’appareil sur un lit, divan, tapis ou
autre surface similaires. Ne placez pas cet appareil à proximité d’un élément
de chauffage ni d’une plinthe électrique. De plus, ne l’installez pas dans une
unité murale ou un cabinet fermé qui ne possède pas d’aération adéquate.
9. Ne faites fonctionner cet appareil qu’avec le type d’alimentation indiqué
sur les étiquettes de l’appareil. Si vous ne connaissez pas le voltage de votre
maison, consultez votre marchand ou votre fournisseur d’électricité.
10. Ne déposez rien sur le cordon d’alimentation. Installez cet appareil dans
un endroit sécuritaire, là où personne ne pourra trébucher sur la ligne
d’alimentation ni le cordon téléphonique modulaire.
11. N’insérez jamais d’objets à travers les fentes et ouvertures de cet appareil, car
ils pourraient toucher à des points de tension dangereux ou court-circuiter
des pièces, ce qui constituerait un risque d’incendie ou d’électrocution.
N’échappez pas de liquides dans l’appareil.
12. Afin de réduire les risques d’électrocution, ne démontez pas l’appareil,
mais apportez-le plutôt à un centre de service qualifié s’il doit être réparé.
En enlevant le couvercle, vous vous exposez à des tensions dangereuses
ou autres dangers similaires. Un remontage inadéquat peut être à l’origine
d’une électrocution lors d’une utilisation ultérieure de l’appareil. Débranchez
l’appareil avant de procéder au nettoyage. Utilisez un chiffon humide et doux.
13. Ne surchargez pas les prises de courant et les rallonges.
14. Débranchez cet appareil de la prise de courant et communiquez avec le
département de service à la clientèle de VTech dans les cas suivants:
Lorsque le cordon d’alimentation est endommagé ou écorché.
Si du liquide a été échappé dans l’appareil.
Si l’appareil a été exposé à une source d’humidité telle que la pluie ou
l’eau.
Si le produit ne fonctionne pas normalement en respectant les instructions
de fonctionnement. Réglez uniquement les commandes indiquées dans
le les instructions de fonctionnement. Les réglages incorrects des autres
commandes pourraient provoquer un dommage qui pourrait exiger
un travail exhaustif de la part d’un technicien autorisé afin de rétablir le
fonctionnement normal de l’appareil.
Si le produit a été échappé et que le socle et/ou le combiné a été
endommagé.
Si le produit affiche une nette diminution de sa performance.
15. Évitez d’utiliser un téléphone (autre qu’un sans fil) pendant un orage. Les
éclairs peuvent être à l’origine d’une électrocution.
16. N’utilisez pas le téléphone pour rapporter une fuite de gaz à proximité de
la fuite. En certaines circonstances, une flammèche pourrait être provoquée
lorsque l’adaptateur est branché à une prise de courant, ou lorsque le combiné
est déposé sur le socle. Ceci est un événement commun associé à la fermeture
d’un circuit électrique. L’utilisateur ne devrait pas brancher le téléphone à
une prise de courant, et ne devrait pas déposer le combiné chargé sur le
socle, si le téléphone se trouve à proximité d’un endroit comportant des
concentrations de gaz inflammables, à moins que la ventilation soit adéquate.
Une flammèche dans un tel endroit pourrait provoquer un incendie ou une
explosion. De tels environnements peuvent comprendre: des endroits où l’on
utilise de l’oxygène médical sans ventilation adéquate; des gaz industriels
(dissolvants de nettoyage, des vapeurs d’essence, etc.); une fuite de gaz
naturel, etc.
17. Ne placez que le combiné de votre téléphone près de votre oreille lorsqu’en
mode de conversation.
18. Ces adaptateurs ont été conçus pour être orientés enposition verticale ou
montés au sol. Les broches ne sont pas conçues pour maintenir l’adaptateur
en place si celui-ci est barnché dans une prise au plafond ou sous une table/
armoire.
19. Pour le MATERIEL RACCORDE PAR PRISE DE COURANT, le socle de prise
de courant doit etre installe a proximite du materiel et doit etre aisement
accessible.
20. N’utilisez que les adaptateurs inclus avec ce produit. L’utilisation d’un
adaptateur dont la polarité ou la tension serait inadéquate risque
d’endommager sérieusement le produit et mettre votre sécurité en péril.
21. La plaque signalétique appliquée est située au bas ou à proximité du produit.
CONSERVEZ CES INSTRUCTIONS
FCC. ACTA and IC Regulations
FCC Part 15
NOTE: This equipment has been tested and found to comply with the requirements
for a Class B digital device under Part 15 of the Federal Communications
Commission (FCC) rules. These requirements are intended to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
WARNING: Changes or modifications to this equipment not expressly approved
by the party responsible for compliance could void the user’s authority to operate
the equipment. This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation. Privacy of communications may
not be ensured when using this telephone.
This Class B digital apparatus complies with Canadian requirement: CAN ICES-3
(B)/ NMB-3(B).
FCC Part 68 and ACTA
This equipment complies with Part 68 of the FCC rules and with technical
equirements adopted by the Administrative Council for Terminal Attachments
(ACTA). The label on the back or bottom of this equipment contains, among other
things, a product identifier in the format US:AAAEQ##TXXXX. This identifier must
be provided to your telephone service provider upon request. The plug and jack
used to connect this equipment to premises wiring and the telephone network
must comply with applicable Part 68 rules and technical equirements adopted
by ACTA.
A compliant telephone cord and modular plug is provided with this product. It
is designed to be connected to a compatible modular jack that is also compliant.
An RJ11 jack should normally be used for connecting to a single line. See the
installation instructions in the user’s manual.
The Ringer Equivalence Number (REN) is used to determine how many devices
you may connect to your telephone line and still have them ring when you are
called. The REN for this product is encoded as the 6th and 7th characters following
the US: in the product identifier (e.g., if ## is 03, the REN is 0.3). In most, but not all
areas, the sum of all RENs should be five (5.0) or less. For more information, please
contact your telephone service provider. This equipment must not be used with
Party Lines. If you have specially wired alarm dialing equipment connected to your
telephone line, ensure the connection of this equipment does not disable your
alarm equipment. If you have questions about what will disable alarm equipment,
consult your telephone service provider or a qualified installer. If this equipment
is malfunctioning, it must be unplugged from the modular jack until the problem
has been corrected. Replacement to this telephone equipment can only be made
by the manufacturer or its authorized agents. For replacement procedures, follow
the instructions outlined under the Limited warranty.
If this equipment is causing harm to the telephone network, the telephone
service provider may temporarily discontinue your telephone service. The
telephone service provider is required to notify you before interrupting service.
If advance notice is not practical, you will be notified as soon as possible. You
will be given the opportunity to correct the problem and the telephone service
provider is required to inform you of your right to file a complaint with the FCC.
Your telephone service provider may make changes in its facilities, equipment,
operation, or procedures that could affect the proper functioning of this product.
The telephone service provider is required to notify you if such changes are
planned. This product is equipped with a corded handset, it is hearing aid
compatible. If this product has memory dialing locations, you may choose to store
emergency telephone numbers (e.g., police, fire, medical) in these locations. If
you do store or test emergency numbers, please: Remain on the line and briefly
explain the reason for the call before hanging up. Perform such activities in off-
peak hours, such as early morning or late evening.
Industry Canada
This device contains licence-exempt transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions: (1) This device may not cause
interference. (2) This device must accept any interference, including interference
that may cause undesired operation of the device. Privacy of communications may
not be ensured when using this telephone. The term ‘’IC:‘’ before the certification/
registration number only signifies that the Industry Canada technical specifications
were met. The Ringer Equivalence Number (REN) for this terminal equipment is
1.0. The REN indicates the maximum number of devices allowed to be connected
to a telephone interface. The termination of an interface may consist of any
combination of devices subject only to the requirement that the sum of the RENs
of all the devices not exceed five. This product meets the applicable Innovation,
Science and Economic Development Canada technical specifications.
US
CA
  • Page 1 1
  • Page 2 2

VTech CD1153 Manuel utilisateur

Catégorie
Téléphones
Taper
Manuel utilisateur

dans d''autres langues