Clover Mini (2nd generation)
Model Number: C302U (United States and Canada LTE)
FCC ID: HFS-C302U
IC: 1787B-C302U
Model Number: C302U (United States and Canada Wi-Fi)
FCC ID: HFS-C302W
IC: 1787B-C302W
HVIN: C302W
Model Number: C302L (Argentina)
CNC ID: C-22360
Model Number: C302E (Europe LTE)
Model Number: C302E (Europe Wi-Fi)
The FCC ID & IC certiicates are not applicable to C302E and C302L
Waste Electrical and Electronic Equipment-WEEE
NOTE: This product is covered electronic equipment under the European Union’s Waste from
Electrical and Electronic Equipment (“WEEE”) Directive (2012/19/EU). The WEEE Directive requires
that covered equipment be collected and managed separately from typical household waste in
all EU member states. Please follow the guidance of your local environmental authority or ask the
shop where you purchased the product for collection or recycling options.
Clover Network, Inc.
415 N Mathilda Ave
Sunnyvale, CA 94085, USA
Patent
clover.com/patents
EU Declaration of Conformity
Hereby, Clover Network, Inc. declares that the radio equipment type, C302E is in compliance with Directive
2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address:
eu.clover.com/eu-compliance
The frequency band and the maximum transmitted power in EU are listed below:
2400MHz - 2483.5MHz: 19.5 dBm (EIRP)
5150MHz - 5250MHz: 20.5 dBm (EIRP)
5250MHz – 5350MHz: 26 dBm (EIRP)
5470MHz - 5725MHz: 26.5 dBm (EIRP)
The following LTE band power is only for C302E (Europe LTE)
LTE Band 3: 23 dBm (conducted)
LTE Band 7: 23 dBm (conducted)
LTE Band 20: 22.5 dBm (conducted)
NFC (13.56MHz): -11.33 dBµA/m (@10m)
LTE band power is not applicable to C302E (Europe Wi-Fi)
5150MHz-5350MHz is for indoor use only.
Caution: Exposure to Radio Frequency Radiation
This equipment complies with EU radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body.
1
4
5
6
7
2
3
EU Importer: Marketplace Merchant Solutions Ltd
Unit 9, Richview Oice Park
Clonskeagh, Dublin 14, Ireland
Plug in last, to a grounded AC
power outlet.
Brancher en dernier sur une prise de
courant alternatif (CA) mise à la terre.
Zuletzt einstecken.
Enchufe al último.
Collegare per ultimo.
Sluit als laatste aan.
FCC Part 15
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, (2) This device must accept any
interference received, including interference that may cause undesired operation.
FCC Part 15 Class B-speciic
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment o and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Warning
Changes or modiications not expressly approved by the party responsible for compliance could
void the user‘s authority to operate the equipment.
FCC exposure limit compliance statement (SAR statement)
This equipment complies with radio frequency (RF) exposure limits adopted by the Federal
Communications Commission for an uncontrolled environment. This equipment should be installed
and operated with minimum distance 20 cm between the radiator & your body.
FCC Part 15
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, (2) This device must accept any
interference received, including interference that may cause undesired operation.
FCC Part 15 Class B-speciic
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment o and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Warning
Changes or modiications not expressly approved by the party responsible for compliance could
void the user‘s authority to operate the equipment.
FCC exposure limit compliance statement (SAR statement)
This equipment complies with radio frequency (RF) exposure limits adopted by the Federal
Communications Commission for an uncontrolled environment. This equipment should be installed
and operated with minimum distance 20 cm between the radiator & your body.
Innovation, Science and Economic Development Canada (ISED) statement:
CAN ICES-3 (B)/NMB-3(B)
This device complies with ISED’s license-exempt RSSs. Operation is subject to the following two
conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d’en compromettre le fonctionnement.
The device could automatically discontinue transmission in case of absence of information to
transmit, or operational failure. Note that this is not intended to prohibit transmission of control or
signaling information or the use of repetitive codes where required by the technology.
• The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the
potential for harmful interference to co-channel mobile satellite systems;
• The maximum antenna gain permitted for devices in the bands 5250–5350 MHz and 5470–5725
MHz shall comply with the e.i.r.p. limit; an
• The maximum antenna gain permitted for devices in the band 5725–5825 MHz shall comply with
the e.i.r.p. limits speciied for point-to-point and non point-to-point operation as appropriate.
In addition, high-power radars are allocated as primary users (i.e. priority users) of the bands
5250–5350 MHz and 5650–5850 MHz and that these radars could cause interference and/or
damage to LE-LAN devices.
Innovation, Science and Economic Development Canada (ISED) statement:
CAN ICES-3 (B)/NMB-3(B)
This device complies with ISED’s license-exempt RSSs. Operation is subject to the following two
conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d’en compromettre le fonctionnement.
The device could automatically discontinue transmission in case of absence of information to
transmit, or operational failure. Note that this is not intended to prohibit transmission of control or
signaling information or the use of repetitive codes where required by the technology.
• The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the
potential for harmful interference to co-channel mobile satellite systems;
• The maximum antenna gain permitted for devices in the bands 5250–5350 MHz and 5470–5725
MHz shall comply with the e.i.r.p. limit; an
• The maximum antenna gain permitted for devices in the band 5725–5825 MHz shall comply with
the e.i.r.p. limits speciied for point-to-point and non point-to-point operation as appropriate.
In addition, high-power radars are allocated as primary users (i.e. priority users) of the bands
5250–5350 MHz and 5650–5850 MHz and that these radars could cause interference and/or
damage to LE-LAN devices.
L’appareil pourrait automatiquement interrompre la transmission s’il n’y a aucune information à
transmettre ou en cas de panne fonctionnelle. À noter que l’objectif de cette disposition n’est pas
d’empêcher la transmission d’informations de contrôle ou de signalisation, ou encore l’utilisation de
codes répétitifs exigés par la technique.
• L’appareil fonctionnant dans la bande comprise entre 5150 et 5250MHz est uniquement
réservé à une utilisation en intérieur, ain de réduire le risque d’interférences nocives aux
systèmes mobiles par satellite utilisant le même canal;
• Le gain d’antenne maximum autorisé pour les appareils fonctionnant dans les bandes comprises
entre 5250 et 5350MHz, et entre 5470 et 5725MHz, doit se conformer à la limite de p.i.r.e.; et
• Le gain d’antenne maximum autorisé pour les appareils fonctionnant dans la bande comprise
entre 5 725 et 5825MHz doit se conformer aux limites de p.i.r.e. spéciiées pour l’exploitation
point à point et non point à point, selon le cas.
De plus, les utilisateurs de radars de haute puissance sont désignés comme utilisateurs principaux (c.-à-d.
comme utilisateurs prioritaires) des bandes comprises entre 5250 et 5350MHz, et entre 5650 et 5850
MHz, et ces radars pourraient causer des interférences et/ou des dommages aux appareils LAN-EL.
This equipment complies with IC RSS-102 RF exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20 cm
between the radiator & your body.
Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un
environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm
de distance entre la source de rayonnement et votre corps.
CE RF Exposure Compliance
This device meets the EU requirements (1999/519/EC) and the International Commission on
Non-Ionizing Radiation Protection (ICNIRP) on the limitation of exposure of the general public to
electromagnetic ields by way of health protection.
This device is restricted to indoor use only when operating in the 5150 to 5350 MHz frequency range.
L’appareil pourrait automatiquement interrompre la transmission s’il n’y a aucune information à
transmettre ou en cas de panne fonctionnelle. À noter que l’objectif de cette disposition n’est pas
d’empêcher la transmission d’informations de contrôle ou de signalisation, ou encore l’utilisation de
codes répétitifs exigés par la technique.
• L’appareil fonctionnant dans la bande comprise entre 5150 et 5250MHz est uniquement
réservé à une utilisation en intérieur, ain de réduire le risque d’interférences nocives aux
systèmes mobiles par satellite utilisant le même canal;
• Le gain d’antenne maximum autorisé pour les appareils fonctionnant dans les bandes comprises
entre 5250 et 5350MHz, et entre 5470 et 5725MHz, doit se conformer à la limite de p.i.r.e.; et
• Le gain d’antenne maximum autorisé pour les appareils fonctionnant dans la bande comprise
entre 5 725 et 5825MHz doit se conformer aux limites de p.i.r.e. spéciiées pour l’exploitation
point à point et non point à point, selon le cas.
De plus, les utilisateurs de radars de haute puissance sont désignés comme utilisateurs principaux (c.-à-d.
comme utilisateurs prioritaires) des bandes comprises entre 5250 et 5350MHz, et entre 5650 et 5850
MHz, et ces radars pourraient causer des interférences et/ou des dommages aux appareils LAN-EL.
This equipment complies with IC RSS-102 RF exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20 cm
between the radiator & your body.
Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un
environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm
de distance entre la source de rayonnement et votre corps.
CE RF Exposure Compliance
This device meets the EU requirements (1999/519/EC) and the International Commission on
Non-Ionizing Radiation Protection (ICNIRP) on the limitation of exposure of the general public to
electromagnetic ields by way of health protection.
This device is restricted to indoor use only when operating in the 5150 to 5350 MHz frequency range.
IMPORTANT for UK Power Adapter Cord
If the available socket outlet is not suitable for the plug supplied with this equipment, it should be
cut o and an appropriate three pin plug itted. With alternative plugs on approved 3 amp fuse must
be itted in the plug or adaptor or in the main fuse box.
NOTE: The plug severed from the mains lead must be destroyed, as a plug with bared lexible cords
is hazardous if engaged in a live socket outlet. In the event of replacing the plug fuse, use a 3 amp
fuse approved by ASTA to BS 1362, ie carries the mark. Always replace the fuse cover, never use
plugs with the fuse cover omitted.
WARNING — THIS APPLIANCE MUST BE EARTHED.
The wires in this mains lead are coloured in accordance with the following code:
Green-and-Yellow = Earth Blue = Neutral Brown = Live
As the colour of the wiring in the mains lead of this appliance may not correspond with the
coloured markings identifying the terminals in your plug, proceed as follows:
• The wire which is coloured Green-and-Yellow must be connected to the terminal in the plug
which is marked with the letter “E”, or by the earth symbol or coloured Green-and-Yellow.
• The wire which is coloured Blue must be connected to the terminal which is marked with the
letter “N” or coloured Black or Blue.
• The wire which is coloured Brown must be connected to the terminal which is marked with the
letter “L” or coloured Red or Brown.
IMPORTANT for UK Power Adapter Cord
If the available socket outlet is not suitable for the plug supplied with this equipment, it should be
cut o and an appropriate three pin plug itted. With alternative plugs on approved 3 amp fuse must
be itted in the plug or adaptor or in the main fuse box.
NOTE: The plug severed from the mains lead must be destroyed, as a plug with bared lexible cords
is hazardous if engaged in a live socket outlet. In the event of replacing the plug fuse, use a 3 amp
fuse approved by ASTA to BS 1362, ie carries the mark. Always replace the fuse cover, never use
plugs with the fuse cover omitted.
WARNING — THIS APPLIANCE MUST BE EARTHED.
The wires in this mains lead are coloured in accordance with the following code:
Green-and-Yellow = Earth Blue = Neutral Brown = Live
As the colour of the wiring in the mains lead of this appliance may not correspond with the
coloured markings identifying the terminals in your plug, proceed as follows:
• The wire which is coloured Green-and-Yellow must be connected to the terminal in the plug
which is marked with the letter “E”, or by the earth symbol or coloured Green-and-Yellow.
• The wire which is coloured Blue must be connected to the terminal which is marked with the
letter “N” or coloured Black or Blue.
• The wire which is coloured Brown must be connected to the terminal which is marked with the
letter “L” or coloured Red or Brown.
Mini
Quick Start Guide
Kurzanleitung · Instructions de démarrage · Guía de inicio rápido
Guida introduttiva · Snelstartgids
clover.com/help
Este producto utiliza para su funcionamiento una fuente de
alimentación, modelo FSP040-RHBN3 marca Clover con las
siguientes características técnicas: Entrada: AC 100-240 V,
50-60 Hz, 1.5 A, Cl. I; Salida: DC 12 V, 3.33 A, que ha sido
certificada para su utilización en el mercado argentino.
Conectar una fuente diferente a
la provista podría ocasionar un
incendio o choque eléctrico.
No utilice una fuente diferente
a la provista con el equipo.
Argentina:
-
1
-
2
