Operating Instructions
Ref: 547-7360 / 19.12.23P-18-008-02-e
Model Order Code
TempTest Blue 292-910
TempTest 2 Blue 292-857
ThermoWorks, Inc.
Utah, U.S.A.
Ph: 801-756-7705 Fax: 801-756-8948
www.thermoworks.com
SPECIFICATIONS
–58 to 572°F (–49.9 to 299.9°C)
±0.7°F (±0.4°C) from –58 to 392°F
(–49.9 to 199.9°C)
otherwise ±1.8°F (±1.0°C)
2-3 sec. (reads to within 1°F of nal
temperature of an ice bath in 3 sec.)
0.1°
2 x AAA / 1,000 hours
High-performance Type K thermocouple
Requires Bluetooth 4.1 or above
0.125 dia. x 4.3 L inches
(3.3 dia. x 109 L mm) with reduced tip to
0.06 dia. inches (1.5 dia. mm)
IP67
Bluetooth 4.0
–4 to 122°F (–20 to 50°C)
4.7 H x 1.9 W x 0.7 D inches
(120 H x 47 W x 17 D mm)
3.7 oz. (105 g)
NIST-traceable certicate included
Range
Accuracy
Response
Resolution
Battery
Sensor Type
Connection
Probe
Water Resistance
Wireless Comm.
Environmental
Range
Dimensions
Weight
Calibration
RADIO CERTIFICATIONS
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy, and if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment o and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this device must accept
any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne
doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of
a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce
potential radio interference to other users, the antenna type and its gain should be so chosen that
the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful
communication.
Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner
avec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé pour l’émetteur par
Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l’intention des
autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope
rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une
communication satisfaisante.
TempTest™Blue
Thermometer &
TempTest™ 2 Blue
Thermometer
INSTRUMENT OPERATION - The instrument is switched
on by pressing the Transmit button. The instrument
takes approximately 2 seconds to start up. After this the
temperature is displayed and the instrument continues to
measure at its set measurement rate (default 1 second).
The instrument is now ready for a Bluetooth® connection
to a smart device, but can be used without a wireless
connection.
Apply the tip of the probe to the substance, medium or
surface to be measured. The sensor is located at the tip of
the probe, therefore the minimum depth insertion should
be 0.12″ (3 mm).
The probe tip is very sharp and can remain hot therefore
caution should be taken when using.
CONNECTION - Use a Bluetooth® enabled iOS or Android™
host device with compatible app installed to connect to
the instrument. When connecting/disconnecting, the
instrument's amber light ashes rapidly 5 times.
Please Note: No readings are stored in the instrument.
When not connected, the instrument can still be used.
Readings are taken and displayed every 1 second.
TRANSMIT BUTTON FUNCTIONS:
• On – Press to switch the instrument on.
• Measure/Transmit – Press to measure
temperature and transmit result via Bluetooth
wireless technology (if connected).
• O – hold down for 3 seconds to switch the
instrument o.
LCD INDICATIONS
The LCD automatically rotates to indicate temperatures at
the angle the instrument is being held.
- Indicates a low battery level – see Battery
Replacement section.
• ‘Hi’ – temperature reading is above 572°F
• ‘Lo’ – temperature reading is below –58°F
• ‘AHi’ – instruments ambient is above 122°F
• ‘ALo’ – instruments ambient is below –4°F
• ‘Err’ – sensor fault or open circuit
LED INDICATIONS
The instrument has an amber light located just above the
LCD to indicate Bluetooth connection status:
• 5 rapid ashes indicate when connecting or
disconnecting.
• A single ash every 10 seconds indicates you are still
connected.
• When connected and the Transmit button is pressed,
a single ash indicates that the temperature has
been transmitted via Bluetooth wireless technology.
SETTINGS - Adjustable via the app and include: °C or °F,
Measurement Interval, Auto-o Interval, Sensor Name,
and High/Low Alarm levels. All settings are stored in the
instrument and are downloaded to the app on connection.
AUTO-OFF - If the instrument is not connected to a smart
device or the Transmit button is not pressed within the set
Auto-o interval (default 10 minutes) then it will switch o.
BATTERY REPLACEMENT - The low battery symbol will
indicate when the batteries need replacing. The instrument
continues to measure accurately but it’s recommended that
the batteries are changed as soon as possible. To replace
the batteries, remove the battery cover on the bottom
using phillips screwdriver. Replace the 2 x AAA batteries
ensuring correct polarities. Replace the cover and tighten
to ensure the unit remains waterproof. Do not overtighten.
Please note: the battery cover can only be tted one way.
INSTRUMENT CLEANING - Clean the entire probe shaft
with a probe wipe after each use to prevent bacteria
growth. Clean instrument body with a damp, soapy cloth
and dry thoroughly. (NOTE: cleaning wipes and solvents
containing Isopropyl Alcohol (IPA) may cause damage to the
instrument enclosure and display screen, and will void the
warranty)
GUARANTEE - This instrument carries a two-year
warranty against defects in either components or
workmanship. During this period, products that prove
to be defective will, at the discretion of ThermoWorks,
be either repaired or replaced without charge. This
warranty does not apply to probes, where a six-month
period is oered. Full details of liability are available
within ThermoWorks’ Terms & Conditions of Sale at
www.thermoworks.com/product-warranty.
The Bluetooth® word mark and logos are registered
trademarks owned by Bluetooth SIG, Inc. and any use of
such marks by ThermoWorks is under license.
Google Play and the Google Play logo are trademarks of
Google Inc. Android is a trademark of Google Inc.
Apple, the Apple logo, iPhone, and iPod touch are
trademarks of Apple Inc., registered in the U.S. and
other countries. App Store is a service mark of Apple Inc.,
registered in the U.S. and other countries.
iOS is a trademark or registered trademark of Cisco in the
U.S. and other countries and is used under license.
-
1
-
2
ThermoWorks TempTest™ Blue Mode d'emploi
- Taper
- Mode d'emploi
- Ce manuel convient également à
dans d''autres langues
Documents connexes
Autres documents
-
TRIMBLE R580 Mode d'emploi
-
Yamaha TA2 Le manuel du propriétaire
-
BW Technologies BW-CONNECT Guide d'installation
-
-
UEi HUB8 Le manuel du propriétaire
-
TRIMBLE R580 GNSS Mode d'emploi
-
UEi HUB2 Le manuel du propriétaire
-
-
Yamaha PSR-SX900 Le manuel du propriétaire
