BEL LEC480 Guide d'installation

Marque: BEL

Modèle: LEC480

Taper: Guide d'installation

LEC480-24

INPUT:

100 – 240 VAC, 2.5 —5 A, 50 - 60 Hz (UL certified) or 120 - 370 VDC

OUTPUT:

24 VDC, 20 A

LEC480-48

INPUT:

100 – 240 VAC, 2.5 —5 A, 50 - 60 Hz (UL certified) or 120 - 370 VDC

OUTPUT:

48 VDC, 10 A

SAFETY according to:

IEC/EN/UL 62368, UL 61010, UL 508

READ THIS CAREFULLY BEFORE

INSTALLATION!

VOR DER INSTALLATION BITTE FOLGENDE

SICHERHEITSHINWEISE BEACHTEN!

LEGGERE ATTENTAMENTE PRIMA

DELL’INSTALLAZIONE!

A LIRE ATTENTIVEMENT AVANT

L’INSTALLATION!

Before operating, read this document

thoroughly and retain it for future reference.

Non-respect of these instructions may reduce

performances and safety of the devices and

cause danger for people and property

Lesen Sie dieses Dokument vor der Inbetriebnahme

sorgfältig durch und bewahren Sie es zum späteren

Nachschlagen auf. Die Nichtbeachtung dieser

Anweisungen kann die Funktion und Sicherheit der

Geräte beeinträchtigen und birgt Gefahren für

Personen und Eigentum.Haftung für die Folgen, die

sich aus dem Einsatz dieses Gerätes ergeben.

Prima dell’installazione, leggere attentamente

questo documento istruzioni e conservarle per

future consultazioni. L’inosservanza delle presenti

istruzioni può compromettere le caratteristiche e

la sicurezza dell’apparecchio e causare pericolo

per le persone e le cose.

Lire ces instructions avant l'installation, conserver

ce manuel pour référence future. Défaut de se

conformer à ces instructions peut affecter les

caractéristiques et la sécurité du dispositif, et

causer du danger aux personnes ou aux biens

CAUTION

ACHTUNG

ATTENZIONE

AVVERTISSEMENT

RISK OF BURNS, EXPLOSION, FIRE,

ELECTRICAL SHOCK, PERSONAL INJURY.

1. Do not use this power supply without proper

grounding (protective grounding), use the

wiring terminals on the input components

instead of the screws on the shell for

grounding;

2. Before performing operations on the

equipment, turn off the power supply to

provide protection to avoid accidentally re-

energizing;

3. Comply with all local and national

regulations to ensure correct wiring;

4. Do not modify or repair this product;

5.Do not open the unit as high voltages are

present inside;

6. Take care to prevent any foreign matter from

entering the shell;

7. Do not use this product in humid places or

areas where moisture or condensation may

occur;

8. When the power is turned on and just after it

is turned off, do not touch it. The hot surface

may cause burns;

Gefahr von Stromschlag, Feuer, Körperverletzung

oder Tod:

1. Verwenden Sie dieses Netzteil nicht ohne

ordnungsgemäße Erdung (Schutzerdung).

Verwenden Sie zur Erdung die Anschlussklemmen

an den Eingangskomponenten anstelle der

Schrauben am Gehäuse;

2. Schalten Sie vor dem Ausführen von Arbeiten am

Gerät die Stromversorgung aus, um ein

versehentliches Wiedereinschalten zu vermeiden.

3. Beachten Sie alle lokalen und nationalen

Vorschriften, um eine korrekte Verdrahtung zu

gewährleisten;

4. Modifizieren oder reparieren Sie dieses Produkt

nicht;

5. Öffnen Sie das Gerät nicht, da im Inneren hohe

Spannungen anliegen;

6. Achten Sie darauf, dass keine Fremdkörper in die

Schale gelangen;

7. Verwenden Sie dieses Produkt nicht an feuchten

Orten oder in Bereichen, in denen Feuchtigkeit oder

Kondensation auftreten kann;

8. Berühren Sie das Gerät beim Einschalten und kurz

nach dem Ausschalten nicht, da die heiße

Oberfläche Verbrennungen verursachen kann.

Rischio di scosse elettriche, incendi, lesioni

personali o morte:

1. Non utilizzare questo alimentatore senza

un'adeguata messa a terra (messa a terra di

protezione), utilizzare i terminali di cablaggio sui

componenti di ingresso invece delle viti sul guscio

per la messa a terra;

2. Prima di eseguire operazioni

sull'apparecchiatura, togliere l'alimentazione per

fornire protezione per evitare la riaccensione

accidentale;

3. Osservare tutte le normative locali e nazionali

per garantire un cablaggio corretto;

4. Non modificare o riparare questo prodotto;

5.Non aprire il dispositivo poiché all'interno sono

presenti alte tensioni

6. Fare attenzione ad evitare che corpi estranei

entrino nel guscio;

7. Non utilizzare questo prodotto in luoghi umidi o

aree in cui potrebbe verificarsi umidità o

condensa;

8. Quando l'apparecchio è acceso e subito dopo

averlo spento, non toccarlo.La superficie calda

può causare ustioni..

Risque de choc électrique, d’incendie, de

blessures corporelles ou de décès:

1. N'utilisez pas cette alimentation sans mise à la

terre appropriée (mise à la terre de protection),

utilisez les bornes de câblage sur les composants

d'entrée au lieu des vis sur la coque pour la mise

à la terre ;

2. Avant d'effectuer des opérations sur

l'équipement, coupez l'alimentation électrique

pour assurer une protection afin d'éviter une

remise sous tension accidentelle ;

3. Respectez toutes les réglementations locales

et nationales pour garantir un câblage correct ;

4. Ne modifiez ni ne réparez ce produit ;

5.N'ouvrez pas l'appareil car il y a de hautes

tensions à l'intérieur

6. Prendre soin d'éviter que des corps étrangers

ne pénètrent dans la coque ;

7. N'utilisez pas ce produit dans des endroits

humides ou des zones où de l'humidité ou de la

condensation peuvent se produire ;

8. Lorsque l'appareil est allumé et juste après

l'avoir éteint, ne le touchez pas. La surface

chaude peut provoquer des brûlures.

INTENDED USE

BESTIMMUNGSGEMÄßER BETRIEB

USO PREVISTO

UTILISATION

These are designed to be mounted on DIN rails

and installed in protective enclosures. They are

suitable for general purposes, such as

industrial control, communications, and

instrumentation equipment.

Do not use these devices in applications where

malfunctions may cause personal injury or

death.

Diese sind für die Montage auf DIN-Schienen und

den Einbau in Schutzgehäuse vorgesehen. Sie

eignen sich für allgemeine Zwecke, wie z. B.

industrielle Steuerungs-, Kommunikations- und

Instrumentierungsausrüstung.

Verwenden Sie diese Geräte nicht in Anwendungen,

bei denen Fehlfunktionen zu Verletzungen oder zum

Tod führen können.

Questi sono progettati per essere montati su

guide DIN e installati in custodie protettive. Sono

adatti per scopi generali, come controllo

industriale, comunicazioni e apparecchiature di

strumentazione.

Non utilizzare questi dispositivi in applicazioni in

cui malfunzionamenti possono causare lesioni

personali o morte.

Ceux-ci sont conçus pour être montés sur des

rails DIN et installés dans des boîtiers de

protection. Ils conviennent à des usages

généraux, tels que les équipements de contrôle

industriel, de communication et d'instrumentation.

N'utilisez pas ces appareils dans des applications

où des dysfonctionnements peuvent causer des

blessures ou la mort.

ENVIRONMENTAL CHARACTERISTICS

UMGEBUNGSBEDINGUNGEN

CARATTERISTICHE AMBIENTALI

CARACTÉRISTIQUES ENVIRONMENTALES

Installation in a Pollution Degree 2

environment.

Do not use in wet area or subject to moisture.

Carefully recycle the product and related

batteries according to local regulations.

Installation in einer Umgebung mit

Verschmutzungsgrad 2.

Nicht in nassen Bereichen oder unter Feuchtigkeit

verwenden.

Das Gerät und die zugehörigen Batterien sind

entsprechend den lokalen Vorschriften zu recyceln

bzw. zu entsorgen.

Usare in ambienti con Grado di Inquinamento 2.

Non far funzionare l'apparecchio in un ambiente

umido o soggetto a formazione di condensa.

Riciclare il prodotto e le batterie collegate, nel

rispetto delle normative locali vigenti.

Utiliser les produits dans des environnements

avec degré de pollution 2.

Ne pas employer l'appareil dans un

environnement humide ou soumis à la

condensation. Recycler les produits et les

batteries, conformément à la réglementation

locale.

LEC480 Series

[email protected]

USER INSTRUCTIONS

1) DESCRIPTION

DIN rail-mounted main switching power supply, with 85 - 264 VAC (120 - 370 VDC) input, suitable for single-phase power lines and DC lines.

2) INSTALLATION

Use DIN-rails according to EN 60715. Installation should be made vertically (see Fig. 4). For better device stability fix the rail to the wall close to the point where the

device is to be mounted. To guarantee sufficient convection, we recommend observing a minimum distance to other modules (see Fig. 3).

The product has over-temperature protection；restricted airflow will cause local temperatures to be too high, which may trigger the over-temperature protection to

restart after cooling;

To get normal operation reduce the temperature of the air surrounding the power supply, increase the ventilation or reduce the load (see Fig. 8)

3) CONNECTIONS

The device is equipped with screw terminal blocks. To avoid sparks, do not connect or disconnect the connectors before having previously turned-off input power and

waited for internal capacitors discharge (minimum 1 minute).

In order to comply with UL certification,

When the ambient temperature is ≤ 60°C, use a copper wire with a specification of ≥ 90°C

When the ambient temperature is > 60°C and ≤ 85°C, use a copper wire with a specification of ≥ 105°C;

Only use wires with a minimum insulation strength of 300 V (input) and 60 V (output).

Strip the connection end of the wire according to the instructions, and make sure that all strands of the twisted wire enter the terminal connection (see Fig. 5)

4) INPUT PROTECTION

The device input is provided with varistors against overvoltage. Input is provided with internal fuses 8A(T)/ 250 VAC, thus an external short circuit / overcurrent

protection must be provided by the end user (see Fig. 6).

For operation on a single-phase system, a protection fuse on the phase must be provided.

Surge protection: it is strongly recommended to provide external surge arresters (SPD) according to local regulations.

5) AC INPUT CONNECTION

The device can be connected to single phase AC line with rated Vin 100 - 240 VAC (see Fig. 7). Please connect the PE first.

6) DC INPUT CONNECTION

Connect L terminal to (+) positive pole, N terminal to (-) negative pole and PE terminal to GND. Rated voltage 120 – 370 VDC.

The device is also suitable for photovoltaic or wind turbine applications (see Fig. 7).

7) OUTPUT CONNECTION

Vout can be adjusted with a potentiometer to a wide range (see Fig. 1)

Check Vout before connecting the power supply to the load. With output voltage set to the max. value, the continuous [current x voltage] must not exceed the

nominal power.

8) OUTPUT PROTECTION

The device is protected against overload (OL) / short circuit (SC) / overvoltage (OV) / overtemperature (OT).

Overload (OL) hiccup mode description:

When the power supply provides 105%~150% of the rated output current, there are two protection modes. The power supply will first enter the hiccup protection mode at

a certain overload current point. The output overload current continues to increase, and the product will enter the constant current hiccup mode; (due to different input

voltages, different output voltage overload protection points are different and cannot be accurately given)

Overload (OL) enters hiccup mode 1:

When the output power is 105%~150% of the rated output power, the output voltage is the nominal voltage, keep it constant for 1s (typical value) and then turn off the

product output, and output after 10 s (typical value) Restart, the power will start on/off cycle hiccup mode until the abnormality is eliminated.

Overload (OL) enters constant current (CC) hiccup mode 2:

When the output power is 105%~150% of the rated output power, the output current continues to increase, triggering the constant current hiccup protection mode, the

output voltage drops and depends on the impedance of the faulty load circuit After the output current is constant for 1s (typical value), the output of the product will be

turned off, and the output will restart after 10s (typical value), and the power will start to turn on/off cycle hiccup mode until the abnormality is eliminated.

Short circuit (SC) enters constant current (CC) hiccup mode:

When the output load is short-circuited, the output voltage is close to 0V, the output current is constant, the power supply can provide 105%~150% constant output

current, and the product will be turned off after 1s (typical value) operation Output, the output restarts after 10 s (typical value), and then the device starts the on/off cycle

hiccup mode until the abnormality is eliminated.

Output OV circuit protection

24 V

：

overvoltage protection range 29 V – 35 V, output voltage turn off or clamp, re-power on for recover or automatically recover.

48 V

：

overvoltage protection range 56 V – 60 V, output voltage turn off or clamp, re-power on for recover or automatically recover.

OT protection:

Turns off the device if the internal temperature exceeds a safe limit. The device restarts automatically after cooling down. To recover to normal operation, reduce air

temperature surrounding the power supply, increase cooling or reduce load.

9) FEEDING DC MOTORS

It is possible to feed DC motors considering that when a motor starts-up under effort its consumption is much higher than the nominal current and it can trigger

overcurrent protection. (See accessory device.)

NOTE: motors can generate high conducted noise on the DC line. Therefore, it is not recommended to feed on the same line motors and equipment sensitive to noise.

10) OPERATION WITH BATTERY

When a battery is connected in parallel to the Output for backup purposes (see accessory device).

INSTALLATION INSTRUCTION

Manufacturer

Bel Fuse Inc.

206 Van Vorst St.

Jersey City

NJ 07302, USA

Asia-Pacific

+86 755 2988 5888

Europe, Middle East

+353 61 49 8941

North America

+1 866 513 2839

BCM.20051_B

FIG. 1 - CONNECTIONS

FIG. 2 - DIMENSIONS

FIG. 3 - DISTANCES

* Pin 8 and the grounding screw (at the bottom) are

interconnected. Either Pin 8 or the grounding screw

need to be connected to earth.

Dimension

mm (in)

48.0 (1.89)

131.5 (5.177)

125.0 (4.921)

Distance

mm (in)

50 (2.0)

100 (4.0))

FIG. 4 - MOUNTING / DISMOUNTING INSTRUCTIONS

For DIN rail fastening according to IEC 60715 TH35-7.5(-15)

Mounting as shown in figure, with input terminals on lower side, with suitable cooling and maintaining a proper distance between adjacent devices as specified in the

Installation Instruction of each family.

MOUNTING:

1. Set the top of the power supply (A) on the

top of the DIN rail (B) to latch.

Press the bottom of the power supply (D)

against the rail to lock it in the position on

the rail (C).

2. Correctly installed power supply (vertically).

3. Insert the copper wires into the top and

bottom terminals and tighten them with a

screwdriver.

4. Adjust the output voltage with a suitable tool