Husqvarna 525P5S Manuel utilisateur

525PT5S

EN Operator's manual 2-27

FR-CA Manuel d’utilisation 28-55

ES-MX Manual del usuario 56-82

Contents

Introduction..................................................................... 2

Safety..............................................................................4

Assembly........................................................................ 9

Operation...................................................................... 11

Maintenance................................................................. 15

Troubleshooting............................................................ 23

Transportation, storage and disposal........................... 23

Technical data.............................................................. 24

Accessories.................................................................. 24

Warranty....................................................................... 26

Introduction

Intended use

The product is used for cutting branches and twigs.

Note: National or local regulations can regulate the use.

Comply to given regulations.

Only use the product with accessories that are approved

by the manufacturer. Refer to

Accessories on page 24

.

Product overview

14

15

13

12

11

10

17

18

22

23

9

5

7

26

25

24

27

28

29

6

8

3

2

1

19

21

20

16

4

1. Saw chain

2. Guide bar

3. Bar nut

4. Protective guard for saw chain

5. Locking knob

6. Chain lubrication adjustment screw

7. Chain oil tank

8. Chain tensioning screw

9. Shaft

10. Front handle

11. Harness support hook

12. Stop switch

2 712 - 002 -

13. Throttle trigger lockout

14. Spark plug cap and spark plug

15. Cylinder cover

16. Starter handle

17. Impact guard

18. Fuel tank

19. Air filter cover

20. Air purge

21. Choke control

22. Throttle trigger

23. Throttle/hand guard

24. Operator's manual

25. Harness

26. Transport guard, bar

27. Combination wrench, chain tensioner

28. Combination wrench

29. Hex key

Symbols on the product

WARNING! This product is dangerous.

Injury or death can occur to the operator or

bystanders if the product is not used

carefully and correctly. To prevent injury to

the operator or bystanders, read and obey

all safety instructions in the operator's

manual.

Please read the operator's manual carefully

and make sure that you understand the

instructions before use.

Use a protective helmet in locations where

objects can fall on you. Use approved

hearing protection. Use approved eye

protection.

Use approved protective gloves.

Use heavy-duty slip-resistant boots.

Fuel.

Chain oil.

Adjustment of the oil flow.

Primer bulb.

Choke.

yyyywwxxxx

The rating plate shows the serial

number. yyyy is the production

year, ww is the production week

and xxxx is the sequential number.

This product is not electrically insulated. If the product touches or comes close to high-volt-

age power lines it could lead to death or serious injury. Electricity can jump from one point to

another by arcing. The higher the voltage, the greater the distance electricity can jump. Elec-

tricity can also travel through branches and other objects, especially if they are wet. Always

keep a distance of at least 10 m between the machine and high-voltage power lines and/or

any objects that are touching them. If you have to work within this safe distance you should

always contact the relevant power company to make sure the power is switched off before

you start work.

The operator of the product must ensure, while working, that no persons or animals come

closer than 15 meters.

Note: Other symbols/decals on the product refer to

certification requirements for other commercial areas.

712 - 002 - 3

EPA III

The Emissions Compliance Period referred to on the

Emission Compliance label indicates the number of

operating hours for which the engine has been shown to

meet Federal emissions requirement. Maintenance,

replacement or repair of the emission control devices

and system may be performed by any nonroad engine

repair establishment or individual.

Proposition 65

WARNING

The engine exhaust from this product

contains chemicals known to the State of

California to cause cancer, birth defects

or other reproductive harm.

Product liability

As referred to in the product liability laws, we are not

liable for damages that our product causes if:

• the product is incorrectly repaired.

• the product is repaired with parts that are not from

the manufacturer or not approved by the

manufacturer.

• the product has an accessory that is not from the

manufacturer or not approved by the manufacturer.

• the product is not repaired at an approved service

center or by an approved authority.

Safety

Safety definitions

Warnings, cautions and notes are used to point out

specially important parts of the manual.

WARNING: Used if there is a risk of injury or

death for the operator or bystanders if the

instructions in the manual are not obeyed.

CAUTION: Used if there is a risk of damage

to the product, other materials or the

adjacent area if the instructions in the

manual are not obeyed.

Note: Used to give more information that is necessary in

a given situation.

General safety instructions

WARNING: Read the warning instructions

that follow before you use the product.

• This product produces an electromagnetic field

during operation. This field may under some

circumstances interfere with active or passive

medical implants. To reduce the risk of serious or

fatal injury we recommend persons with medical

implants to consult their physician and the medical

implant manufacturer before operating this product.

• This product is a dangerous tool if you are not

careful or if you use the product incorrectly. This

product can cause serious injury or death to the

operator or others.

• It is very important that you read and understand the

contents of this operator’s manual. If you feel

uncertainty about a work situation or the operating

4 712 - 002 -

procedures after you read the operator's manual,

speak to a service agent before you continue.

• Under no circumstances may the design of the

product be modified without the permission of the

manufacturer. Do not use a product that appears to

have been modified by others and only use

accessories recommended for this product. Non-

authorized modifications and/or accessories can

result in serious personal injury or the death of the

operator or others.

• Do a check of the product before use. Refer to

Safety devices on the product on page 7

and

To

check before starting on page 11

. Do not use a

defective product. Do the safety checks,

maintenance and service instructions described in

this manual.

Safety instructions for assembly

WARNING: Read, understand and obey

these instructions carefully before you use

the product.

• The complete clutch cover and shaft must be fitted

before the machine is started, otherwise the clutch

can come loose and cause personal injury.

• The only accessories you can operate with this

product are the cutting attachments we recommend.

Refer to

Accessories on page 24

.

• Use approved protective gloves.

• Make sure that you assemble the protective cover

and shaft correctly before you start the engine.

• To operate the product safely and prevent injury to

the operator or other persons, the product must

always be attached correctly to the harness.

Safety instructions for operation

WARNING:

Read the warning instructions

that follow before you do maintenance on

the product.

• Use personal protective equipment, refer to

Personal

protective equipment on page 6

.

• This product is not electrically insulated. If the

product touches or comes close to high-voltage

power lines it could lead to death or serious bodily

injury. Electricity can jump from one point to another

by arcing. The higher the voltage, the greater the

distance electricity can jump. Electricity can also

travel through branches and other objects, especially

if they are wet. Always keep a distance of at least 10

m between the product and high-voltage power lines

and/or any objects that are touching them. If have to

work within this safe distance you should always

contact the relevant power company to make sure

the power is switched off before you start work.

• Overexposure to vibration can lead to circulatory

damage or nerve damage in persons who have poor

circulation. Speak to your physician if you

experience symptoms of overexposure to vibration.

Such symptoms include numbness, loss of feeling,

tingling, pricking, pain, loss of strength, changes in

skin colour or condition. These symptoms usually

show in the fingers, hands or wrists. The risk

increases at low temperatures.

• The inside of the muffler contain chemicals that may

be carcinogenic. Avoid contact with these elements

in the event of a damaged muffler. Long term

inhalation of the engine’s exhaust fumes, chain oil

mist and sawdust can represent a health risk.

• Never use the machine indoors or in spaces lacking

proper ventilation. Exhaust fumes contain carbon

monoxide, an odourless, poisonous and highly

dangerous gas.

• Do not operate a product without a muffler or with a

defective muffler. A defective muffler can increase

the noise level and the risk of fire. Keep fire

extinguishing tools near. If you must have a spark

arrestor mesh in your area, do not use the product

without or with a broken spark arrestor mesh.

• If the saw chain does not stop when idling, adjust the

idle speed. Refer to

To adjust the idle speed on page

16

. Do not use the product until it is correctly

adjusted or repaired.

• This product has a long reach. Make sure that no

people or animals come closer than 15 m when the

product is running.Always look behind you before

you turn around with the product. Stop the product

immediately if a person or animal enters the 15 m

safety zone. If more than one operator does work in

the same area, keep a safety distance of a minimum

of 15 m.

• Observe the applicable safety regulations for work in

the vicinity of overhead power lines. Also falling

branches can result in short-circuiting.

• Never stand directly underneath a branch that is

being cut. This could lead to serious or even fatal

personal injury.

• Watch out for stumps of branches that can be thrown

out when you cut. Do not cut too close to the ground

where stones and other objects can be thrown out.

• Do not operate the product in bad weather, such as

dense fog, heavy rain, strong wind and intense cold.

To operate in bad weather can make you tired and

add risks, such as icy ground and unpredictable

felling direction.

• Do not use the product if you are tired, ill, or under

the influence of alcohol, drugs or medicine, as this

has a negative effect on your vision, alertness,

coordination and judgment.

• Make sure that you can move safely and have a safe

stance. Examine the area around you for obstacles

such as roots, rocks, branch and ditches. Be careful

during work on slopes.

• Do not remove the cut material, or let other persons

remove cut material, while the engine is on or the

cutting equipment rotates, as this can result in

serious injury.

712 - 002 -

5

• Do not overreach. Keep a stable position of the feet

and a good balance at all times.

• Always hold the product with both hands. Hold the

product on the right side of your body.

• Keep your hands and feet away from the saw chain

until it has stopped completely when the product is

deactivated.

• Never work from a ladder, stool or any other raised

position that is not fully secured.

• Do not put the product down with the engine on

unless you have it in clear view.

• Listen for warning signals and loud voices when you

use hearing protection. Always remove your hearing

protection when the engine stops.

• Stop the engine before you move to a new work

area. Always attach the transport guard before you

move the equipment.

• Never allow children to use or be in the vicinity of the

product. Remove the spark plug cap when the

product is not under close supervision.

Personal protective equipment

WARNING: Read the warning instructions

that follow before you use the product.

• Always use approved personal protective equipment

when you use the product. Personal protective

equipment cannot fully prevent injury but it

decreases the degree of injury if an accident does

occur. Let your dealer help you select the right

equipment.

• Use a protective helmet where there is a risk of

falling objects.

• Use approved hearing protection that provides

adequate noise reduction. Long-term exposure to

noise can result in permanent hearing impairment.

• Use approved eye protection. If you use a visor, you

must also use approved protective goggles.

Approved protective goggles must comply with the

ANSI Z87.1 standard in the USAs or EN 166 in EU

countries.

• Use gloves when necessary, for example when you

attach, examine or clean the cutting equipment.

• Use sturdy non-slip boots.

• Use clothing made of a strong fabric. Always use

heavy, long pants and long sleeves. Do not use

loose clothing that can catch on twigs and branches.

Do not wear jewelry, short pants, sandals or go with

bare feet. Put your hair up safely above shoulder

level.

• Keep first aid equipment close at hand.

6

712 - 002 -

Safety devices on the product

WARNING: Read the warning instructions

that follow before you use the product.

• Do not use a product with defective safety devices.

• Do a check of the safety devices regularly. Refer to

Safety devices on the product on page 7

.

• If the safety devices are defective, speak to your

Husqvarna servicing dealer.

To do a check of the throttle trigger lockout

The throttle lockout is designed to prevent accidental

operation of the throttle control.

1. Press the throttle trigger lockout (A) and make sure

that the throttle control is released (B). When you

release the handle the throttle control and the throttle

trigger lockout both move back to their initial

positions. This movement is controlled by two

independent return springs. This arrangement

means that the throttle control is automatically

locked at the idle setting.

A

B

2. Make sure that the throttle control is locked at the

idle setting when the throttle trigger lockout is

released.

3. Press the throttle trigger lockout and make sure that

it returns to its intial position when you release it.

4. Do a check of the throttle control and throttle trigger

lockout move freely and that the return springs work

properly.

5. Start the product (refer to instructions under

To start

the product on page 14

) and apply full throttle.

6. Release the throttle and make sure that the saw

chain stops and remains at a standstill. If the saw

chain rotates with the throttle in the idle position the

carburettor idle setting must be checked. Refer to

instructions under the chapter

Maintenance on page

15

.

To do a check of the stop switch

1. Start the engine.

2. Move the stop switch to the stop position and make

sure that the engine stops.

To do a check of the vibration damping system

The vibration damping system decreases vibration in the

handles to a minimum which makes the operation

easier. The vibration damping system of the product

decreases the transfer of vibration between the engine

unit and the shaft unit of the product.

1. Stop the engine.

712 - 002 -

7

2. Do a visual check for deformation and damage for

example, cracks.

3. Make sure you attach the elements of the vibration

damping system correctly.

To do a check of the muffler

The muffler keeps noise levels to a minimum and directs

exhaust fumes away from the operator. In areas with a

hot, dry weather there is a high risk of fire. Obey local

regulations and maintenance instructions

• Do a visual check for damage and deformation.

• Make sure that the muffler is correctly attached to

the product.

• Do a visual check on the spark arrestor mesh.

Refer to

To do maintenance on the muffler on page

16

.

Fuel safety

• Do not mix the fuel indoor or near a heat source.

• Do not start the product if there is fuel or engine oil

on the product. Remove the unwanted fuel/oil and let

the product dry. Remove unwanted fuel from the

product.

• If you spill fuel on your clothing, change clothing

immediately.

• Do not get fuel on your body, it can cause injury. If

you get fuel on your body, use a soap and water to

remove the fuel.

• Do not start the engine if you spill oil or fuel on the

product or on your body.

• Do not start the product if the engine has a leak.

Examine the engine for leaks regularly.

• Be careful with fuel. Fuel is flammable and the fumes

are explosive and can cause injuries or death.

• Do not breathe in the fuel fumes, it can cause injury.

Make sure that there is a sufficient airflow.

• Do not smoke near the fuel or the engine.

• Do not put warm objects near the fuel or the engine.

• Do not add the fuel when the engine is on.

• Make sure that the engine is cool before you refuel.

• Before you refuel, open the fuel tank cap slowly and

release the pressure carefully.

• Do not add fuel to the engine in an indoor area. Not

sufficient airflow can cause injury or death because

of asphyxiation or carbon monoxide.

• Tighten the fuel tank cap carefully or a fire can

occur.

• Move the product at a minimum of 3 m (10 ft) from

the position where you filled the tank before a start.

• Do not put too much fuel in the fuel tank.

• Make sure that a leak cannot occur when you move

the product or fuel container.

• Do not put the product or a fuel container where

there is an open flame, spark or pilot light. Make

sure that the storage area does not contain an open

flame.

• Only use approved containers when you move the

fuel or put the fuel into storage.

• Empty the fuel tank before long-term storage. Obey

the local law on where to dispose fuel.

• Clean the product before long-term storage.

8

712 - 002 -

• Remove the spark plug cable before you put the

product into storage to make sure that the engine

does not start accidentally.

Safety instructions for maintenance

WARNING: Read the warning instructions

that follow before you do maintenance on

the product.

• Do only the maintenance and servicing given in this

operator's manual. Let professional servicing

personnel do all other servicing and repairs.

• Regularly do the safety checks, maintenance and

service instructions given in this manual. Regular

maintenance increases the life of the product and

decreases the risk of accidents. Refer to

Maintenance on page 15

for instructions.

• If the safety checks in this operator's manual is not

approved after you do maintenance, speak to your

servicing dealer. We guarantee that there are

professional repairs and servicing available for your

product.

Safety instructions for the cutting

equipment

WARNING: Read the warning instructions

that follow before you use the product.

• Only use the guide bar/saw chain combinations and

filing equipment that we recommend. Refer to

Accessories on page 24

for instructions.

• Use protective gloves when you use or do

maintenance on the saw chain. A saw chain that

does not move can also cause injuries.

• Keep the cutting teeth correctly sharpened. Obey the

instructions and use the recommended file gauge. A

saw chain that is damaged or incorrectly sharpened

increases the risk of accidents.

• Keep the correct depth gauge setting. Obey the

instructions and use the recommended depth gauge

setting.

• Make sure that the saw chain has the correct

tension. If the saw chain is not tight against the guide

bar, the saw chain can derail. An incorrect saw chain

tension increases wear on the guide bar, saw chain

and chain drive sprocket. Refer to

To tension the

chain on page 21

.

• Do maintenance on the cutting equipment regularly

and keep it correctly lubricated. If the saw chain is

not correctly lubricated, the risk of wear on the guide

bar, saw chain and chain drive sprocket increases.

Assembly

To assemble the cutting head

CAUTION: Make sure that the drive shaft

inside the shaft engages with the cut-out in

the cutting head.

712 - 002 - 9

A

B

1. Loosen the screw on the cutting head. (A)

2. Fit the cutting head on the shaft so that the screw (A)

is aligned with the hole in the shaft as shown.

3. Finger tighten the screw (A). Make sure that screw

(A) fits into the hole in the shaft.

4. Tighten screw (A).

5. Tighten screw (B).

To assemble the bar and chain

1. Unscrew the bar nut and remove the protective

cover.

2. Fit the bar over the bar bolt. Place the bar in its

rearmost position. Place the chain over the drive

sprocket and in the groove on the bar. Begin on the

top side of the bar.

3. Make sure that the edges of the cutting links are

facing forward on the top edge of the guide bar.

4. Fit the cover and locate the chain adjuster pin (A) in

the hole in the bar. Check that the drive links of the

chain fit correctly on the drive sprocket (B) and that

the chain is in the groove in the bar (C). Tighten the

bar nut finger-tight.

A

B

5. Tension the chain by turning the chain tensioning

screw clockwise using the combination spanner. The

chain should be tensioned until it does not sag from

the underside of the bar.

6. The chain is correctly tensioned when it does not

sag from the underside of the bar, but can still be

turned easily by hand. Hold up the bar tip and tighten

the bar nuts with the combination spanner.

7. When fitting a new chain, the chain tension has to be

checked frequently until the chain is run-in. Check

the chain tension regularly. A correctly tensioned

chain ensures good cutting performance and long

life.

To adjust the length of the shaft

1. Undo the knob.

2. Pull out the shaft to the desired length.

10

712 - 002 -

3. Tighten the knob.

To adjust the harness

Always use the harness when you operate the product.

The harness gives maximum control during operation of

the product. The harness decreases the risk of tiredness

in your arms and back.

1. Put on the harness.

2. Attach the product to the harness support hook.

3. Adjust the length of the harness until the support

hook is roughly level with your right hip.

To assemble the impact guard

1. Assemble the guard with 3 screws.

2. Tighten the screws to 30 ft/lbs (4 Nm).

3. Tighten the screws again when the product has been

in use for about 20 hours.

Operation

Introduction

WARNING: Before you operate the product,

you must read and understand the safety

chapter.

To check before starting

1. Inspect the working area. Remove any objects that

could be thrown out.

2. Check the saw chain. Never use blunt, cracked or

damaged equipment.

3. Check that the product is in perfect working order.

4. Check that all nuts and screws are tight.

5. Make sure the chain is adequately lubricated, refer

to

To check the chain lubrication on page 22

.

6. Check that the saw chain always stops when the

engine is idling.

7. Only use the product for the purpose it was intended

for.

8. Make sure the handle and safety features are in

order. Never use a machine that has any parts

missing or has been modified in relation to the

specification.

Fuel

This product has a two-stroke engine.

CAUTION: Incorrect type of fuel can result

in engine damage. Use a mixture of gasoline

and two-stroke oil.

Premixed fuel

• Use Husqvarna premixed alkylate fuel of a good

quality, for best performance and extension of the

engine life. This fuel contains less harmful chemicals

compared to regular fuel, which decreases harmful

exhaust fumes. The quantity of remains after

combustion is lower with this fuel, which keeps the

components of the engine more clean.

712 - 002 - 11

To mix fuel

Gasoline

CAUTION: Do not use gasoline with an

octane number less than 90 RON (87 AKI).

This can cause damage to the product.

CAUTION: Do not use gasoline with more

than 10% ethanol concentration (E10). This

can cause damage to the product.

• Always use new unleaded gasoline with a minimum

octane number of 90 RON (87 AKI) and with less

than 10% ethanol concentration (E10).

• Use gasoline with a higher octane number if you

frequently use the product at continuously high

engine speed.

Two-stroke oil

• For best results and performance use Husqvarna

two-stroke oil.

• If Husqvarna two-stroke oil is not available, use a

two-stroke oil of good quality for air-cooled engines.

Speak to your servicing dealer to select the correct

oil.

CAUTION: Do not use two-stroke oil for

water-cooled outboard engines, also

referred to as outboard oil. Do not use oil

for four-stroke engines.

To mix gasoline and two-stroke oil

Gasoline, liter Two-stroke

oil, liter

2% (50:1)

5 0.10

10 0.20

15 0.30

20 0.40

CAUTION: Small errors can influence the

ratio of the mixture drastically when you mix

small quantities of fuel. Measure the quantity

of oil carefully and make sure that you get

the correct mixture.

1. Fill half the quantity of gasoline in a clean container

for fuel.

2. Add the full quantity of oil.

3. Shake the fuel mixture.

4. Add the remaining quantity of gasoline to the

container.

5. Carefully shake the fuel mixture.

CAUTION: Do not mix fuel for more than 1

month at a time.

To fill the fuel tank

1. Clean the area around the fuel tank cap.

2. Shake the container and make sure that the fuel is

fully mixed. Use a fuel container with an anti-spill

valve.

3. Fill the fuel tank.

4. Tighten the fuel tank cap carefully.

5. Move the product 3 m (10 ft) or more away from the

refueling area and fuel source before starting.

CAUTION: Contamination in the tanks

causes malfunction. Clean the fuel tank and

chain oil tank regularly and replace the fuel

filter one time a year or more.

To do a run-in

• During the first 10 hours of operation, do not apply

full throttle without load for extended periods.

12

712 - 002 -

To use the correct chain oil

WARNING: Do not use waste oil, which can

cause injury to you and the environment.

Waste oil also causes damage to the oil

pump, the guide bar and the saw chain.

WARNING: The saw chain can break if the

lubrication of the cutting equipment is not

sufficient. Risk of serious injury or death to

the operator.

WARNING: This product has a function that

lets the fuel run out before the chain oil. Use

the correct chain oil for this safety function to

operate correctly. Speak to your servicing

dealer when you select your chain oil.

Note: This product has an automatic chain lubrication

system. You can also adjust the oil flow. Refer to

To

adjust chain lubrication on page 22

.

• Use Husqvarna chain oil for maximum saw chain life

and to minimise environmental damage. If

Husqvarna chain oil is not available, we recommend

you to use a standard chain oil.

• Use a chain oil with good adherence to the saw

chain.

• Use a chain oil with correct viscosity range that

agrees with the air temperature.

CAUTION:

If the oil is too thin, it runs out

before the fuel. In temperatures below

0°C/32°F some chain oils become too

thick, which can cause damage to the oil

pump components.

• Use the recommended cutting equipment. Refer to

Accessories on page 24

.

To use the product

• Hold the product as close to your body as possible to

get the best balance. Use the harness to support the

weight of the machine and make it easier to handle.

• Make sure that the tip does not touch the ground.

• Do not rush the work, but work steadily until all the

branches have been cut back cleanly.

• Always slow the engine to idle speed after each

working operation. Long periods at full throttle

without any load on the engine can lead to serious

engine damage.

• Always work at full throttle.

• Whenever possible position yourself so that you can

make the cut at right angles to the branch.

90°

• Do not work with the shaft held straight out in front of

you (like a fishing rod) as this increases the apparent

weight of the cutting attachment.

• Cut large branches in sections so that you have

better control over where they fall.

• Never cut through the swelling at the root of the

branch as this will slow down healing and increase

the risk of fungal attack!

• Use the stop at the base of the cutting head to

provide support during cutting. This will help prevent

the cutting attachment from ”jumping” on the branch.

712 - 002 -

13

• Make an initial cut on the underside of the branch

before cutting through the branch. This will prevent

tearing of the bark, which could lead to slow healing

and cause permanent damage to the tree. The cut

should not be deeper than 1/3 of the branch

thickness to prevent jamming. Keep the chain

running while you withdraw the cutting attachment

from the branch to prevent it jamming.

• Use the harness to support the weight of the

machine and make it easier to handle.

• Make sure you have a firm footing and that you can

work without being hampered by branches, stones

and trees.

WARNING: Never activate the throttle

without having the cutting attachment in

full view.

To prepare the product for start

1. Press the air purge repeatedly until the fuel starts to

fill the bulb.

Note:

It is not necessary to fully fill the bulb.

2. Move the choke control up into choke position.

WARNING:

The saw chain will start to

rotate immediately when you start the

engine with the choke.

To start the product

WARNING: Read the warning instructions in

the safety chapter before you start the

product (refer to

Safety on page 4

).

1. Use protective gloves.

2. Hold the body of the product on the ground with your

left hand.

CAUTION: Do not use your feet!

3. Hold the starter rope handle.

4. Slowly pull out the starter rope with your right hand

until you feel some resistance (the starter pawl grip).

WARNING: Do not twist the starter rope

around your hand.

5. Pull the cord quickly and with power.

CAUTION: Do not pull the starter rope

all the way out and do not let go off the

starter rope handle when the starter rope

is fully extended. This can cause

damage to the product.

6. Pull the starter rope again and again until the engine

starts.

7. Reset the choke when the engine fires.

8. Operate the throttle gradually when the engine

starts.

9. Make sure the engine runs smoothly.

About the surface

WARNING:

Do not put parts of your body in

the grey marked area. If you touch the grey

marked area it can result in burns to the

skin. It can also cause electrical shock if the

spark plug cap has been damaged. Do not

use a product with a damaged spark plug

cap.

14 712 - 002 -

To stop the product

1. Move the stop switch into the stop position to stop

the engine.

CAUTION: The stop switch

automatically goes back to its initial

position. In order to prevent accidental

starting, the spark plug cap must be

removed from the spark plug when

assembling, checking and/or

maintenance is done.

Maintenance

Introduction

Below you will find some general maintenance

instructions. If you need further information please

contact your service workshop.

Maintenance schedule

The following is a list of the maintenance steps that must

be performed on the product. Most of the items are

described later in this chapter.

Note: The user must only carry out the maintenance

and service work described in this operator's manual.

More extensive work must be carried out by an

authorized service workshop.

Maintenance Daily Weekly Monthly

Clean the external surface. X

Make sure that the throttle trigger lock and the throttle works correctly. X

Do a check of the stop switch to make sure that it works correctly. X

Make sure that the saw chain does not rotate at idle speed. X

Clean the air filter. Replace if necessary. X

Check the saw chain with regard to visible cracks in the rivets and links, whether

the saw chain is stiff or whether the rivets and links are abnormally worn.

X

Clean the area under the protective cover. X

Make sure that the screws and nuts are tight. X

Examine the engine, the fuel tank and the fuel lines for leaks. X

Clean the cooling system. X

712 - 002 - 15

Maintenance Daily Weekly Monthly

Examine the starter and the starter rope for damages. X

Examine the vibration damping elements for damages and cracks. X

Clean the outside of the spark plug. Remove it and do a check of the electrode

gap. Adjust the gap to the correct distance (refer to

Technical data on page 24

)

or replace the spark plug. Make sure that the spark plug is fitted with a suppres-

sor.

X

Clean the outside of the carburettor and the space around it. X

File off any burrs from the edges of the bar. X

Clean or replace the spark arrestor mesh on the muffler. X

Clean the fuel tank. X

Do a check of the fuel filter for contamination and the fuel hose for cracks or oth-

er defects. Replace if neccessary.

X

Do a check of all cables and connections. X

Do a check of the clutch, clutch springs and the clutch drum for wear. Replace if

neccessary by an autorized service workshop.

X

Replace the spark plug. Make sure that the spark plug is fitted with a suppres-

sor.

X

To adjust the idle speed

1. Make sure that the air filter is clean and the air filter

cover is attached before you adjust the idle speed.

2. Start the product. Refer to

To start the product on

page 14

3. Adjust the idle speed with the idle adjustment screw

T which is identified with "T" mark. Turn the idle

adjustment screw clockwise until the saw chain

starts to turn.

4. Turn the idle adjustment screw counterclockwise

until the saw chain stops.

The idle speed is correct when the engine operates

smoothly in all positions. The idle speed must be below

the speed when the saw chain starts to turn.

WARNING: If the saw chain does not stop

when you adjust the idle speed, turn to your

nearest servicing dealer. Do not use the

product until it is correctly adjusted or

repaired.

Note: Refer to

Technical data on page 24

for the

recommended idle speed.

To do maintenance on the muffler

The muffler decreases the noise level and directs the

exhaust gases away from the operator.

WARNING: Mufflers that have catalytic

converters get very hot during operation and

will stay hot for some time after you stop the

product. This also applies at idle speed. If

you touch the product it can result in burns

to the skin. Think about of the risk of fire.

1. Stop the product and let it cool down.

2. Remove the cover to the muffler.

16 712 - 002 -

3. Remove the screw holding the spark arrestor mesh.

4. Clean the spark arrestor mesh if it is blocked or

replace it if it is damaged.

CAUTION: The spark arrestor mesh must

be replaced if it is damaged. Do not use a

product if the spark arrestor mesh on the

muffler is missing or defective.

CAUTION: If the spark arrestor mesh is

frequently blocked it can be a sign that

performance of the catalytic converter is

decreased. Turn to your servicing dealer to

examine the muffler. A blocked spark

arrestor mesh will cause overheating and

result in damage to the cylinder and piston.

Cooling system

The product has a cooling system to keep the operation

temperature as low as possible.

Clean the components of the cooling system with a

brush weekly or more frequently in rougher conditions. A

dirty or blocked cooling system makes the product too

hot which causes damage to the piston and cylinder.

The cooling system has the following components:

1. Air intake on the starter.

2. Fins on the flywheel.

3. Cooling fins on the cylinder.

4. Cylinder cover.

5. Muffler cover.

6. Muffler plate.

1

6

3

4

5

2

To examine the spark plug

CAUTION: Always use the recommended

spark plug type. Incorrect spark plug type

can cause damage to the product.

• Examine the spark plug if the engine is low on

power, is not easy to start or does not operate

correctly at idle speed.

• To decrease the risk of unwanted material on the

spark plug electrodes, obey these instructions:

a) Make sure that the idle speed is correctly

adjusted.

b) Make sure that the fuel mixture is correct.

c) Make sure that the air filter is clean.

• If the spark plug is dirty, clean it and make sure that

the electrode gap is correct, refer to

Technical data

on page 24

.

• Replace the spark plug if it is necessary.

Air filter

Remove dust and dirt from the air filter to keep it clean in

order to prevent:

• Carburettor malfunctions.

• Starting problems.

• Loss of engine power.

• Unnecessary wear to engine parts.

• Too much fuel consumption.

Clean the air filter at an interval of 25 hours, or more

regularly if conditions are unusually dusty.

712 - 002 -

17

To clean the air filter

CAUTION: A air filter that is damaged, very

dirty or soaked with fuel must always be

replaced.

If you use an air filter for a long time it cannot be fully

cleaned. Replace the air filter with a new one at regular

intervals.

1. Move the choke lever up, to close the choke valve.

2. Remove the air filter cover and remove the air filter.

3. Clean the air filter with warm soap water.

4. Replace the air filter if it is too dirty to fully clean it.

Always replace a damaged air filter.

5. Also clean the inner surface of the filter cover. Use

air or a brush.

6. Do a check of the rubber sealing surface. Replace

the filter on the rubber seal if it is damaged.

7. Make sure that the filter is dry before you assemble

it.

To check the chain drive sprocket

1. Regularly check the degree of wear on the drive

sprocket. Replace if wear is excessive.

To examine the cutting equipment

1. Make sure that there are no cracks in rivets and links

and that no rivets are loose. Replace if it is

necessary.

2. Make sure that the saw chain is easy to bend.

Replace the saw chain if it is rigid.

3. Compare the saw chain with a new saw chain to

examine if the rivets and links are worn.

4. Replace the saw chain when the longest part of the

cutting tooth is less than 4 mm/0.16 in. Also replace

the saw chain if there are cracks on the cutters.

To do a check of the guide bar

1. Make sure that the oil channel is not blocked. Clean

if it is necessary.

2. Examine if there are burrs on the edges of the guide

bar. Remove the burrs using a file.

3. Clean the groove in the guide bar.

18

712 - 002 -

4. Examine the groove in the guide bar for wear.

Replace the guide bar if it is necessary.

5. Examine if the guide bar tip is rough or very worn.

6. Make sure that the bar tip sprocket turns freely and

that the lubricating hole in the bar tip sprocket is not

blocked. Clean and lubricate if it is necessary.

7. Turn the guide bar daily to extend its life cycle.

To sharpen the saw chain

Information about the guide bar and saw

chain

WARNING:

Use protective gloves when you

use or do maintenance on the saw chain. A

saw chain that does not move can also

cause injuries.

Replace a worn or damaged guide bar or saw chain with

the guide bar and saw chain combination recommended

by Husqvarna. This is necessary to keep the safety

functions of the product. Refer to

Accessories on page

24

, for a list of replacement bar and chain

combinations that we recommend.

• Guide bar length, in/cm. Information about the guide

bar length can usually be found on the rear end of

the guide bar.

• Number of teeth on bar tip sprocket (T).

• Chain pitch, in. The distance between the drive links

of the saw chain must align with the distance of the

teeth on the bar tip sprocket and drive sprocket.

PITCH =

D

2

• Number of drive links. The number of drive links is

decided by the type of guide bar.

• Bar groove width, in/mm. The groove width in guide

bar must be the same as the chain drive links width.

712 - 002 -

19

• Chain oil hole and hole for chain tensioner. The

guide bar must align with product.

• Drive link width, mm/in.

General information about how to sharpen

the cutters

Do not use a blunt saw chain. If the saw chain is blunt,

you must apply more pressure to push the guide bar

through the wood. If the saw chain is very blunt, there

will be no wood chips but sawdust.

A sharp saw chain eats through the wood and the wood

chips becomes long and thick.

The cutting tooth (A) and the depth gauge (B) together

makes the cutting part of the saw chain, the cutter. The

difference in height between the two gives the cutting

depth (depth gauge setting).

A

B

When you sharpen the cutter, think about the following:

• Filing angle.

• Cutting angle.

• File position.

• Round file diameter.

It is not easy to sharpen a saw chain correctly without

the correct equipment. Use Husqvarna file gauge. This

will help you to keep maximum cutting performance.

Note: Refer to

To sharpen the cutters on page 20

for

information about sharpening of the saw chain.

To sharpen the cutters

1. Use a round file and a file gauge to sharpen the

cutting teeth.

Note:

Refer to

Accessories on page 24

for

information about which file and gauge that

Husqvarna recommends for your saw chain.

2. Apply the file gauge correctly on to the cutter. Refer

to the instruction supplied with the file gauge.

20

712 - 002 -

La page charge ...

Husqvarna 525P5S Manuel utilisateur

Ce manuel convient également à

Husqvarna 525P5S Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents