Teka FS3M S90 GG S/S Manuel utilisateur

Marque: Teka

Modèle: FS3M S90 GG S/S

Catégorie: Fours

Taper: Manuel utilisateur

Ce manuel convient également à

FS3PS90GGS/S

FS3MS90GGS/S

FS3FFS90GGS/S

FS3FFL90GGS/S

3100356

CONTENTS

INSTALLER TECHNICAL MANUAL……………………………………………………………………………

APPLIANCE GAS CONNECTION………………………………………………………………………..

ADAPTATION TO DIFFERENT TYPES OF GAS…………………………………………………………....

BURNER ADJUSTMENT…………………………………………………………………………....

APPLIANCE ELECTRIC CONNECTION……………………………………………………….....

APPLIANCE MAINTENANCE………………………………………………………………………

REPLACING PARTS…………………………………………………………………………………………….

USE AND MAINTENANCE MANUAL………………………………………………………………

CONTROL PANEL DESCRIPTION………………………………………………………………

USING BURNERS…………………………………………………………………………………

USING HOT PLATES……………………………………………………………………………….

USING THE CERAMIC HOB……………………………………………………………………….

TYPE OF PAN…………………………………………………………………………………………………….

USING THE INDUCTION HOB…………………………………………………………………………………..

HOB CONTROL KNOB…………………………………………………………………………………………

HOB………………………………………………………………………………………………………………….

TYPES OF PANS……………………………………………………………………………………………………………

USING THE GAS OVEN (SINGLE CONTROL) …………………………………………………..

USING THE GAS OVEN FOR MODEL WITH DOUBLE CONTROLS………………………..

USING THE CHANGE-OVER SWITCH …………………………………………………….

USING THE ELECTRIC THERMOSTAT ( WITH A MULTIFUNCTION VEN)………………….

USING THE MULTIFUNCTION OVEN ……………………………………………………………..

USING THE NATURAL CONVENTIONAL ELECTRIC OVEN ………………………………..

USING THE VENTILATED ELECTRIC OVEN …………………………………………………………

USING THE GAS GRILL (SINGLE CONTROL) …………………………………………………..

USING THE GAS GRILL FOR MODEL WITH DOUBLE CONTROLS ………………………..

USING THE CONVENTIONAL ELECTRIC GRILL……………………………………………...

USING THE VENTILATED ELECTRIC GRILL ……………………………………………………

USING THE MINUTE-MINDER……………………………………………………………………..

USING THE END OF COOKING TIMER…………………………………………………………..

USING THE DIGITAL CLOCK …………………………………………………………………….

USING THE TOUCH CLOCK ………………………………………………………………………..

USING THE ANALOG CLOCK……………………………………………………………………..

USING THE 3 KEYS ELECTRONIC PROGRAMMER …………………………………………..

ELECTRONIC TIMER PROGRAMMER …………………………………………………………..

USING THE THERMOMETER …………………………………………………………………….

USING THE SELF-CLEANING OVEN………………………………………………………………

CLEANING THE APPLIANCE………………………………………………………………………

AFTER-SALES TECHNICAL SERVICE AND SPARE ARTS…………………………………….

INSTALLATION, MAINTENANCE AND USE INSTRUCTIONS FOR

FREE-STANDING COOKERS 90x60 cm GIANT OVEN

READ THE INSTRUCTION BOOKLET BEFORE INSTALLING AND USING THE APPLIANCE.

The manufacturer will not be responsible for any damage to property or to persons caused by incorrect installation or

improper use of the appliance.

The manufacturer is not responsible for any inaccuracies, due to printing or transcription errors, contained in this booklet. In

addition, the appearance of the figures reported is also purely indicative.

The manufacturer reserves the right to make changes to its products when considered necessary and useful, without affecting

the essential safety and operating characteristics.

THIS APPLIANCE HAS BEEN DESIGNED FOR NON-PROFESSIONAL DOMESTIC USE.

INSTALLING THE SYSTEM TO PREVENT TILTING OF THE APPLIANCE

Caution, possibility of tilting Anti-tip restraints

To prevent the appliance from accidentally tilting, the anti-tip restraints device provided with the appliance must be installed.

Installation instruction are included in the anti-tip restraints device kit supplied.

INSTALLER TECHNICAL MANUAL

APPLIANCE GAS CONNECTION

Before connecting the appliance to the gas network, make sure that the data on the label attached to the food warmer

drawer or on the back of the cooker are compatible with what is indicated for the gas distribution network.

A label attached to the last page of this handbook and in the food warmer drawer (or on the back) of the appliance

indicates the appliance adjustment conditions: type of gas and operating pressure.

IMPORTANT: This appliance must be installed in compliance with current national standards in force and used only in

a well-ventilated room.

WARNING: It should be recalled that the appliance utilises a threaded 1/2" gas cylindrical male fitting according to UNI-

ISO 228-1.

To connect the appliance to the gas network with a flexible rubber hose, a supplemental hose nipple fitting is needed

(see Fig. 1) which is supplied with the appliance.

ADAPTATION TO DIFFERENT TYPES OF GAS

Before performing any maintenance operation, disconnect the appliance from the gas supply and electricity network.

REPLACING THE NOZZLES TO OPERATE WITH ANOTHER TYPE OF GAS:

Follow the instructions below to change the burner nozzles on the work surface:

1) Pull out the plug from the electric outlet to avoid any type of electric contact.

2) Remove the grids from the work surface (Fig. 2).

3) Remove the burners (Fig. 2).

4) Unscrew the nozzles using a 7 mm spanner, and replace them (Fig. 3) with those needed for the new type of gas according

to what is indicated in Table 1.

Follow the instructions below to change the oven burner nozzle:

1) Remove the oven level (Fig. 4-5).

2) Loosen the screw V and pull out the burner from the support being careful not to damage the ignition plug and the

thermocouple (Fig. 6).

3) Unscrew the nozzle R (Fig. 6) using a 7 mm spanner and replace it with the nozzle needed for the new type of gas according

to what is indicated in Table 2 or in Table 3.

Follow the instructions below to change the grill burner nozzle:

1) Loosen the screw at the end of the grill burner and pull out the burner from the support being careful not to damage the

ignition plug and the thermocouple (Fig. 7).

2) Unscrew the nozzle R (Fig. 7) using a 7 mm spanner and replace it with the nozzle needed for the new type of gas according

to what is indicated in Table 2 or in Table 3.

WARNING: After completing the above-mentioned replacements, the technician must adjust the burners, as described

in the paragraph below, seal any adjustment and pre-adjustment devices and apply the label on the

appliance, to replace the existing one, corresponding to the new gas adjustment. This label is contained in

the spare nozzle bag.

Table 1

Burner Types of gas Pressure Nozzle diameter Rater capacity

mbar 1/100 mm. g/h l/h kW kcal/h

Auxiliary Natural G20 20 72 - 95 1 860

Butane G30 28-30 50 73 - 1 860

Propane G31 37 50 71 - 1 860

Semi-rapid Natural G20 20 97 - 167 1,75 1505

Butane G30 28-30 65 127 - 1,75 1505

Propane G31 37 65 125 - 1,75 1505

Rapid Natural G20 20 115 - 286 3 2580

Butane G30 28-30 85 218 - 3 2580

Propane G31 37 85 214 - 3 2580

Ultra rapid Natural G20 20 153 - 405 4,25 3655

4 kW Butane G30 28-30 102 309 - 4,25 3655

Propane G31 37 102 303 - 4,25 3655

Natural G20 20 ext. 155

int. 70

476

4300

Ultra rapid

Dual 5 kW

Butane G30

28-30 ext. 96

int. 46

334 -

4,60 3956

Propane G31

37 ext. 96

int. 46

328 -

4,60 3956

Table 2 (model with gas oven and gas grill with double controls)

Oven Natural G20 20 155 - 429 4,50 3870

Butane G30 28-30 105 327 - 4,50 3870

Propane G31 37 105 321 - 4,50 3870

Grill Natural G20 20 108 - 191 2 1720

Butane G30 28-30 72 145 - 2 1720

Propane G31 37 72 143 - 2 1720

Table 3 (model with gas oven and gas grill with single control, or gas oven and electric grill)

Oven Natural G20 20 155 - 429 4,50 3870

Butane G30 28-30 105 327 - 4,50 3870

Propane G31 37 105 321 - 4,50 3870

Grill Natural G20 20 108 - 191 2 1720

Butane G30 28-30 72 145 - 2 1720

Propane G31 37 72 143 - 2 1720

BURNER ADJUSTMENT

1) Burner "MINIMUM" adjustment:

Work surface burner adjustment: follow the instructions below to adjust the work surface burner minimum:

1) Light the burner and set the knob to the MINIMUM position (small flame).

2) Remove the knob of the valve that is press fit on the rod of that valve.

3) If the cooker is not equipped with safety valves on the surface burners, insert a small slotted screwdriver into the hole on the

valve rod (Fig. 8) and turn the choke screw to the right or left until the burner flame is adjusted to minimum. If the cooker is

equipped with safety valves, the choke valve is not located in the rod hole, but on the valve body (see fig. 9).

4)For the gas valve of dual burner the choke valve is located on the valve body (fig.10), the A screw adjust the outer ring,

the B screw adjust the inner ring.

5) Make sure that the flame does not go out when switching quickly from the MAXIMUM to the MINIMUM position.

Oven burner adjustment: follow the instructions below to adjust the minimum:

1) Light the burner setting the knob to the MAXIMUM position.

2) Close the oven door and operate the oven for at least 10 minutes.

3) Set the knob to the MINIMUM position (corresponding to 120°) and then remove it.

4) With a slotted screwdriver turn the choking screw (see figure 11) and, while observing the flame at the same time through the

cooker porthole, evaluate the consistency of the flame so it remains on when switching quickly from the MINIMUM to the

MAXIMUM position.

Grill burner adjustment: follow the instructions below to adjust the minimum:

1) Light the burner setting the knob to the MAXIMUM position.

2) Close the oven door and operate the oven for at least 10 minutes.

3) Set the knob to the MINIMUM position (small flame) and then remove it.

4) If the cooker is not equipped with safety valves on the surface burners, insert a small slotted screwdriver into the hole on the

valve rod (Fig. 8) and turn the choke screw to the right or left, while observing the flame at the same time through the cooker

porthole, evaluate the consistency of the flame so it remains on when switching quickly from the MINIMUM to the MAXIMUM

position. If the cooker is equipped with safety valves, the choke valve is not located in the rod hole, but on the valve body (see

figure 9).

WARNING: The above-mentioned adjustment should be made only with natural gas burners, while for those operating

with liquid gas the screw must be locked at the end in a clockwise direction.

WARNING: For the model with single control for grill and oven, the grill burner always

operates at maximum and therefore no minimum adjustment is required.

APPLIANCE ELECTRIC CONNECTION:

The electric connection must comply with the current legal standards and regulations.

Before making the connection, check that:

- The system electrical rating and the current outlets are adequate for the maximum power output of the appliance (see the label

applied to the bottom of the casing).

- The outlet or the system is equipped with an efficient ground connection in accordance with the current legal standards and

regulations. The company will not be responsible for the non-compliance with these instructions.

When the connection to the power supply network is made using an outlet:

- If the power cord is supplied without a plug, apply a standard plug that is suitable for the load indicated on the label. Connect

the wires according to the diagram shown in Fig.12 and check that:

letter L (phase) = brown wire;

letter N (neutral) = blue wire;

ground symbol = green-yellow wire;

- The power cord must be positioned so that an overtemperature of 75 K will not be reached at any point.

- Do not use reductions, adapters or splitters since they might cause false contacts and lead to dangerous overheating.

When the connection is made directly to the electric network:

- Insert an omnipolar circuit-breaker between the appliance and the network which is sized for the appliance load with a

minimum opening between the contacts of 3 mm.

- Remember that the ground wire must not be interrupted by the circuit-breaker.

- As an alternative, the electric connection can also be protected by a high-sensitivity residual current circuit-breaker.

- It is highly recommended to attach the special green-yellow ground wire to an efficient ground system.

APPLIANCE MAINTENANCE

ATTENTION: IMPORTANT WARNINGS

For cookers resting on a base

ATTENTION: If the cooker rests on a base, take the measures necessary to prevent the cooker from sliding along the support

base.

For cookers with glass covers

ATTENTION: Before opening the appliance’s glass cover, carefully remove all liquid residues from the top of it.

ATTENTION: Before closing the appliance’s glass cover, make sure that the work surface has cooled.

For cookers with electric ovens

The unit becomes hot during use. Do not touch the heating elements inside the oven.

For cookers with electric ovens

ATTENTION: The accessible parts can become hot during use. Keep children away from the appliance.

For the food warmer compartment (or drop leaf in our case)

ATTENTION: The internal parts of the food warmer can become hot during use.

For glass doors

Do not use abrasive cleaning products or metal spatulas with sharp edges to clean the oven door’s glass since this could

scratch the surface and the glass could break.

Do not use steam cleaners to clean the appliance.

NOTE: various parts of the cooker heat up reaching temperatures which seem very high but which are actually fully within

safety limits. According to these limits:

1) With the oven on at 200°C for 1 hour, front accessible parts which cannot be grasped, can reach the following temperatures:

- Control panel: Tmax = Room Temperature +60°C

- Glass of the oven door: Tmax = Room temperature+60°C

- Metal part of the oven door: Tmax = Room temperature+45°C

2) With the oven on at 230°C for 1 hour, the parts which can be grasped, can reach the following temperatures:

- Plastic knobs: Tmax = Room temperature+60°C

- Metal oven door handle: Tmax = Room temperature+35°C

where the room temperature is the temperature in °C of the place where the appliance is installed.

REPLACING PARTS

Before performing any maintenance operation, disconnect the appliance from the gas supply and electricity network.

To replace parts such as knobs and burners, just remove them from the seats without disassembling any part of the cooker.

To replace parts such as nozzle supports, valves and electric components follow the procedure described in the burner

adjustment paragraph. To replace the valve or the gas thermostat, it is also necessary to disassemble the two rear gas train

brackets, loosening the 4 screws (2 per bracket) that attach it to the rest of the cooker and, unscrew the nuts that attach the

front burner valves to the control support, after removing all the knobs. To replace the gas or electric thermostat, also

disassemble the rear cooker guard, loosening the relative screws, to be able to pull out and reposition the thermostat bulb.

To replace the oven bulb, just unscrew the protection cap that projects out inside the oven.(fig.13)

WARNING: Before replacing the bulb, disconnect the appliance from the electric power supply.

USE AND MAINTENANCE MANUAL

Oven and grill burners should not be used simultaneously

GAS BURNER DIMENSION

Burne

Dimension (mm)

Auxiliary Ø 50

Semi-rapid Ø 70

Rapid Ø 95

Ultra-rapid Ø 125

Ultra-rapid dual Ø 135

ELECTRIC HOT PLATE DIMENSION

TIPE OF PLATE DIMENSION

Electric hot plate Ø 145

Electric hot plate Ø 180

CONTROL PANEL DESCRIPTION

On the control panel, small symbols show the function of each knob or key. Here as follows are the several controls

that a cooker can have:

the symbol or or shows the disposition of burners on the worktop, the full dot identifies the burner in object (in

this case the rear burner on the right).

the symbol

or or shows the running of any oven (2+0 switch, gas oven, gas oven with gas grill, gas oven with

electric grill and multifunction oven)

the symbol

shows the grill (gas grill, electric grill)

the symbol shows the electric thermostat for electric fan oven.

the symbol shows the oven fan working button as to allow the oven to operates with fan assisted gas. The fan operation of

the oven prevents the operation of the grill, which therefore cannot be used with the fan in action.

the symbol

shows the minute minder

the symbol shows the operating key for the rotisserie (only gas oven)

the symbol shows the ignition key for the oven light (all except the electric fan oven)

the symbol shows the push-button for burner ignition

the symbol shows if keys are in position “on” or “off”

USING BURNERS

A diagram is etched on the control panel above each knob which indicates which burner corresponds to that knob. The burners

can be ignited in different ways depending on the type of appliance and its specific characteristics:

- Manual lighting (it is always possible even when the power is cut off): Turn the knob counterclockwise that corresponds

to the burner selected, setting it to the MAXIMUM position at the etched star (large flame Fig.15) and place a lit match up to the

burner.

- Electric ignition:

Turn the knob counterclockwise that corresponds to the burner selected, setting it to the MAXIMUM position

(large flame Fig. 15) and keep on pressing the knob in correspondence of the ignition symbol marked with a star (for cookers

equipped with ignition trough knob) or press the ignition button marked with a star and release it as soon as the burner has

ignited.

- Burner ignition equipped with safety device (thermocouple)(fig.14): Press and turn the knob counterclockwise that

corresponds to the burner selected, setting it to the MAXIMUM position at the etched star (large flame Fig. 15), press the knob

and activate one of the above-mentioned ignition devices. Once ignited, keep pressing the knob for about 10 seconds to allow

the flame to heat the thermocouple. If the burner goes out after releasing the knob, repeat the entire operation.

Note: It is recommended not to try to ignite a burner if the relative flame cap is not in the correct position.

-Use of the dual burner (fig.16)

This model controls both the central and external crown of the burner with just one valve.

To ignite the central crown press and turn the knob to the maximum delivery position 1 and hold it down until ignition: in

this position the internal flame are at maximum of the internal crown.

Turn the knob to position 2 to have the internal crown at the minimum.

Turn the knob to position 3 to have the internal crown ant the external crown at the maximum.

Turn the knob to position 4 to have the internal crown ant the external crown at the minimum.

Tips for using burners correctly:

- Use suitable pots for each burner (see tab. 5 and Fig.18).

- When the liquid is boiling, turn the knob to the MINIMUM position (small flame Fig. 15).

- Always use pots with a cover.

TABLE N°5: Recommended pot diameters.

BURNER

Recommended POT DIAMETERS (cm.)

Auxiliary

12 – 14

Semi-rapid

14 – 26

Rapid

18 – 26

Ultra-rapid

22 – 26

Ultra-rapid dual

22 – 50

WARNING: Use flat-bottomed containers

WARNING: After cleaning, make sure head “B” and covers “A” are properly placed on their seat as figure 17A and not

off-center as in figure 17B

WARNING: If the power is cut off, the burners can be lit with matches. When cooking foods with oil and fat, which are

very flammable, the user should not leave the appliance unattended. If the appliance is equipped with a

glass cover, such a cover may break when heated. Turn off all burners before lowering the cover. Do not

use sprays near the appliance when it is being used.

When using the burners, make sure that the handles of the pots are correctly positioned. Keep children

away from the appliance. If equipped with a cover, before being closed, any food deposits should be

cleaned off the built-in surface.

NOTE: The use of a gas cooking appliance produces heat and humidity in the room where it is installed. Therefore,

proper aeration in the room is needed while ensuring that natural ventilation openings remain unobstructed.

Intensive and continuous use of the appliance may require additional aeration, for example by opening a

window, or more efficient aeration by increasing the power of the mechanical exhauster, if installed.

USING HOT PLATES

These plates are controlled by a switch with 6 settings (see Fig.19). The plates are turned on by turning the knob to the desired

position. The front panel of the appliance is etched with a mark indicating what plate corresponds to the knob. A light, which is

also installed on the control panel turns on, indicating that the plate is on.

How to use a hot plate:

When a hot plate is used for the first time or after a long period of inactivity, it is recommended to use it on position 1 for about

30 minutes to eliminate any humidity absorbed by the internal insulating material.

As example, we have included a table with the adjustments needed to ensure proper use of the hot plates.

WARNING: When a hot plate is used for the first time or after a long period of inactivity, it is necessary to use it on

position 1 for about 30 minutes to eliminate any humidity absorbed by the insulating material.

TABLE N°6

PLATE POSSIBLE COOKING METHODS

0 Plate off

1 To melt butter, chocolate, etc. - To heat small amounts of liquid

2 To heat larger quantities of liquid - To prepare creams and sauces that required extended cooking

3 To defrost foods, cook at boiling temperature

4 To cook roasts with delicate meat and fish

5 For meat roasts and steaks, for large pieces of boiled meat

6 To boil large quantities of water, for frying.

To ensure correct use, remember the following:

- Dry the bottom of the pot before placing it on the plate.

- Use pots with a flat and thick bottom (see Fig. 20).

- Never use pots that are smaller than the plate.

- Turn on the plate only after the pot has been placed on top.

- As soon as a crack appears on the surface of the hot plate, immediately turn off the appliance.

- If the appliance is equipped with a glass cover, it may break when heated.

- Turn off all the plates before closing the cover.

- After use, and to ensure good preservation, the plate should be treated with normal products for electric hot plates

that are available in the market so that the surface is always clean; this operation will prevent any corrosion (rust).

- After they are used, the plates remain hot for a long time; therefore, do not place the hands or other objects on the

plate to avoid burns.

- When using the burners, make sure that the handles of the pots are correctly positioned. Keep children away from the

appliance.

- When cooking foods with oil and fat, which are very flammable, the user should remain near the appliance.

WARNING: As soon as a crack appears on the surface of the hot plate, immediately turn off the appliance.

USING THE CERAMIC HOB

The working table has 5 cooking areas, which differ in power and diameter (Fig.21).

Positions are clearly indicated with screen-printed round areas (see description of the hobs).

The heating process comes inside these areas.

When a worktop hotplate is used for some time, the remaining surface remain hot; a red indicator in the worktop surface light

will indicate it.

To obtain best results, the bottom of the hob should be thick and flat.

The diameter of the bottom of the pot (or other container) should be as near as possible the diameter of the burner you are

using; using a smaller pot will cause waste of energy due to heat dispersion on the uncovered surface of the plate.

The hob surface and the bottom of the pot must be kept clean.

Following these recommendations will help you save energy.

CERAN HOT PLATE

TIPE OF PLATE POWER

A) Ceramic electrical hot plate left front 700/1700W

B) Ceramic electrical hot plate left rear 1200W

D) Ceramic electrical hot plate right rear 1100/2200W

E) Ceramic electrical hot plate right front 1200W

C) Ceramic electrical hot plate central 1400/2200W

Residual heat

Each cooking zone is equipped with a device which warns of residual heat (H). After any cooking zone is switched off, a red

indication light may appear on the display. This warns that the cooking zone concerned is stili very hot. (Fig.22).

How to use the 5 electrical hot plate ceramic hob:

Each worktop cooking hotplate is controlled by an energy regulator switch (for 1 or 2 circuit type hotplate). These allow you

to select different power rates in continuous way from the lower position “0” (plate always “off”) to the higher position “3” (plate

always “on”; double circuit hotplates control switch (Fig. 23) allow to reach the full power rate of the related double circuit

hotplate by turning the related knob in 2

circuit position for 1-2 sec. and the releasing it in pos.3 (Fig. 24).

Directions showing the hotplate and related control knob is indicated on the control panel of the appliance.

A red indication light on the worktop surface will indicate You that some worktop hotplate is turned on.

Once the boiling level has been reached, lower the temperature and let the food simmer.

Experience will guide you in understanding how long to simmer, but obviously this also depends on the food and the kind of pot

you are using. Proper use will permit you to save time and energy.

WARNING:

Under no circumstance use aluminium foil or plastic containers to hold the food while cooking on a glass-ceramic hob.

WARNING:

Do not touch the cooking area as long as the light indicating residual heat on the glass-ceramic hob, is “on”; this

indicates that the temperature in the relative area is still high.

WARNING:

Your glass-ceramic hob is thermal shock resistant and resistant to both heat and cold.

If you drop a heavy pot on your hob it will not break.

On the contrary, if a hard object, such as the salt shaker or the spice bottle strikes the edge or the corner of the hob,

the hob may break.

WARNING: never use the glass-ceramic hob as support surface.

TYPE OF PAN

The pans used for cooking must have certain minimum diameters to ensure satisfactory operation.

Pans larger than the cooking zones can also be used, but it is important to ensure that the bottom of the pan does not touch

other cooking zones, and that it is always centred over the perimeter of the cooking zone.(fig.27-28)

The pans used must not have crowned (concave or convex) bottom. (fig.29)

USING THE INDUCTION HOB

HOB CONTROL KNOB

These knobs provide control of the ceramic hob's cooking zones.

The zone it controls is shown above each knob. Turn the knob to the right to set the zone's operating power; the settings range

from a minimum of 1 to a maximum of 9. (fig. 25)

The working power is shown by a display on the hob.

Heating accelerator

Each cooking zone is equipped with a heating accelerator.

This system allows the zone to be operated at peak power for a time proportional to the heating power selected.

To start the heating accelerator, turn the knob to the left, select setting "A" and then release. The letter "A" will appear on the

display on the hob.

You now have 3 seconds to select the heating setting of your choice. Once a setting between 1 and 9 has been selected, "A"

and the chosen setting will flash in alternation on the display. '

While the heating accelerator is in operation, the heating level can be increased at any time. The "full power" time will be

modified accordingly. If the power is reduced by turning the knob anticlockwise, option "A" is automatically deactivated.

Power Function

The power function allows the user to operate each heating zone continuously at the maximum power for a time of no more than

10 minutes. This function can be used, for example, to bring a large amount of water to the boil in a hurry, or to turn up the heat

under meat.

Turn the knob clockwise and set heating level 9, then use the knob to set the "P" position and release il. "P" appears on the

corresponding zone display.

After 10 minutes, the power is reduced automatically, the knob returns to the 9 setting and the "P" disappears.

However, the power function can be turned off at any time by reducing the heating level. .

When the power function is selected for one heating zone (e.g. the left front zone), the power absorbed by the second zone (Ieft

rear zone) might be reduced to supply the maximum available energy to the first zone.

Consequently, the power function takes priority over the heating accelerator.

If a pan is removed from the cooking zone while the power function is on, the function is switched off.

Holding Function

The holding function keeps the temperature of the bottoms of pans at about 65°C. This allows foods to be kept hot with optimal

energy consumption and to be heated gently. The holding function can be kept in operation for up to 2 hours.

The holding function is and is indicated by the relevant symbols on the cooking zones.

HOB

ATTENTION:

Metal items such as cutlery or lids must never be placed on the surface of the hob since they may become hot.

Cooking zones (fig.26)

The appliance is equipped with 5 cooking zones having different diameters and powers. Their positions are clearly marked by

rings, while the heating power is only released in the area shown on the ceramic hob. The 5 cooking zones are of HIGH-LlGHT

type and start to heat up a few seconds after they are switched on. The heat level of each zone can be regulated from the

minimum to the maximum setting using the knobs on the front panel.

Underneath each cooking zone there is a coil called an inductor, supplied with power by an electronic system, which generates

a variable magnetic field. When a pan is placed inside this magnetic field, the high frequency currents concentrate directly on

the bottom of the pan and produce the heat needed to cook the foods.

The 5 lights between the cooking zones come on when the temperature of one or more cooking zones exceeds 60° C.. The

lights go out when the temperature drops to below about 60° C.

Zone number: Power absorption

Normal operation: With power function:

1 1100W 1400W

2 1100W 1400W

3 1400W 2000W

4 2300W 3000W

5 2300W 3000W

Total power absorption 7400W

When the hob is used for the first time, it should be heated to its maximum temperature for long enough to bum off any oily

residues left by the manufacturing process, which might contaminate foods with unpleasant smells.

TYPES OF PANS

This type of appliance can only operate with pans of special kinds.

The bottom of the pan must be iron or steel/iron to generate the magnetic field necessary for the heating process.

Vessels made from the following materials are not suitable:

 glass;

 porcelain;

 pottery;

 steel, aluminium or copper without magnetic bottom;

To check that a pan is suitable, simply place a magnet close to its bottom:

if the magnet is attracted, the pan is suitable for induction cooking. If no magnet is to hand, put a little water in the pan, place it

on a cooking zone and switch it on. If the symbol

appears on the display instead of the power, the pan is not suitable.

The pans used for cooking must have certain minimum diameters to ensure satisfactory operation.

Pans larger than the cooking zones can also be used, but it is important to ensure that the bottom of the pan does not touch

other cooking zones, and that it is always centred over the perimeter of the cooking zone.(fig.27-28).

Use only vessels specially designed for induction cooking, with thick, completely flat bottom; if these are not available, the pans

used must not have crowned (concave or convex) bottom. (fig.29)

Pan present device

Each cooking zone is equipped with a "pan present" device, which ensures that cooking cannot start unless a suitable pan is

present on the cooking zone and properly positioned.

If the user attempts to switch on the cooking zone with the pan not positioned properly or with a pan which is not of suitable

material, a few seconds after the zone is switched on the

symbol will appear to warn the user that an error has been made.

Residual heat

Each cooking zone is equipped with a device which warns of residual heat. After any cooking zone is switched off, a flashing ‘H’

may appear on the display. This warns that the cooking zone concerned is still very hot. Cooking can be restarted while the ‘H’

is flashing; proceed as described in point "3".

Locking-out the hob

When not in use, the hob can be "Iocked out" to prevent children from accidentally switching it on.

With the cooking zones off, turn the knobs of zones 2 and 4 to the left simultaneously until 5 Ls appear on the power display and

then release the knobs.

To deactivate it, repeat the same procedure: the cooking zone displays will all show 0, indicating that the cooking zone lock-out

function has been deactivated.

Attention: Take care not to spill sugar or sweet mixtures onto the hob during cooking, or to place materials or substances which

might melt (plastic or aluminium foil) on it; if this should occur, to avoid damage to the surface, turn the heating off immediately

and clean with the scraper supplied while the cooking zone is still warm. If the ceramic hob is not cleaned immediately, residues

may form which cannot be removed once the hob has cooled.

Important!

Keep a close eye on children because they are unlikely to see the residual heat warning lights. The cooking zones are still very

hot for some time after use, even if they are switched off. Make sure that children never touch them.

WARNING: Under no circumstance use aluminium foil or plastic containers to hold the food while cooking on a glass-ceramic

hob.

WARNING: Do not touch the cooking area as long as the light indicating residual heat on the glass-ceramic hob, is “on”; this

indicates that the temperature in the relative area is still high.

WARNING: Never place pan with bottoms which are not perfectly flat and smooth on the hob

WARNING: If you notice a crack in the ceramic hob, disconnect the appliance from the electricity supply and contact a service

centre.

WARNING: Your glass-ceramic hob is thermal shock resistant and resistant to both heat and cold.

If you drop a heavy pot on your hob it will not break.

On the contrary, if a hard object, such as the salt shaker or the spice bottle strikes the edge or the corner of the hob, the hob

may break.

WARNING: never use the glass-ceramic hob as support surface

USING THE GAS OVEN (SINGLE CONTROL)

GAS OVEN:

All the gas oven cookers are equipped with a thermostat and safety device to adjust the cooking temperature. The oven

temperature is set by turning the knob counterclockwise to match the indicator with the temperature selected. The gas oven can

be combined with a gas grill or an electric grill. See the specific pages for use information.

FAN GAS OVEN:

Operating the fan of the oven by means of the appropriate switch situated on the control panel, the circulation of warm air

guarantees a uniform heat distribution. The preheating of the oven can be avoided. However for delicate baking, it is preferable

to warm the oven before introducing the baking-pan. The baking system with the fan convection changes in part the various

traditional baking notions. When roasting meat it is not necessary to turn the meat any more and for a roast on the spit, it is not

indispensable to use the spit-roaster, but is sufficient to put the meat directly on the grate.

With the use of the fan gas oven, the baking temperatures are slightly lower of about 10-15°C compared to those in use with the

traditional gas oven. The fan operation of the oven prevents the operation of the grill, which therefore cannot be used with the

fan in action.

The oven can also be used in a traditional way, (by not activating the fan) for foods requiring heat from the bottom, e.g. pizza.

WARNING: If the burner flames are extinguished accidentally, turn off the control knob and do not try to relight the

oven until after at least 1 minute.

The oven burner can be ignited in different ways:

- Manual lighting (it is always possible even when the power is cut off):

To light the oven, open the oven door and turn the knob to the maximum temoerature setting (fig.30-31). At the same time put a

lit match next to the ignition tube that is visible on the oven level (fig.32). Then press the thermostat knob (this makes the gas

start to flow) and keep it pressed, after the burner has been completely lit, for 10 seconds. Release the knob and make sure that

the burner remains on, otherwise repeat the operation.

- Electric ignition (only for the models equipped with this device):

In this case, first open the oven door, then press and turn the knob to the maximum temperature setting (fig.30-31). Then press

the thermostat knob (models with ignition trough knob). Wait about 10 seconds after the burner has been completely lit and then

release the knob. Make sure that the burner remains on, otherwise repeat the operation. As for cookers without ignition trough

knob, press the thermostat knob and the key with the spark symbol, wait about 10 seconds after the burner has been

completely lit and then release the knob. Make sure that the burner remains on, otherwise repeat the operation.

The ignition device should not be used for more than 15 seconds. If after that period the burner still has not been lit, do

not use the device and open the door of the room or wait at least 60 seconds before trying to light the oven again.

WARNING: when trying to light the oven, the door must always be open. When using the oven, leave the cooker cover

open to prevent it from overheating.

NOTICE: when using the oven for the first time it should be operated for 15-30 minutes at a temperature of about 250°

without cooking anything inside in order to eliminate any moisture and odours from the internal insulation.

During normal oven use, after lighting the burner and setting the desired temperature, wait about 15 minutes before putting in

any food to preheat the oven.The oven is equipped with 5 guides (Fig.33) at different heights which can be used to insert

shelves or the tray. To keep the oven as clean as possible it is recommended to cook meat on the tray or on the shelf that has

been inserted inside the tray.

USING THE GAS OVEN FOR MODEL WITH DOUBLE CONTROLS

GAS OVEN:

All the gas oven cookers are equipped with a thermostat and safety device to adjust the cooking temperature. The oven

temperature is set by turning the knob counterclockwise to match the indicator with the temperature selected. The gas oven can

be combined with a gas grill or an electric grill. See the specific pages for use information.

When the cooker model allows the combinated use of gas oven and gas grill, the oven inner temperature is adjustable within the

limit indicated in TABLE 8.

FAN GAS OVEN:

Operating the fan of the oven by means of the appropriate switch situated on the control panel, the circulation of warm air

guarantees a uniform heat distribution. The preheating of the oven can be avoided. However for delicate baking, it is preferable

to warm the oven before introducing the baking-pan. The baking system with the fan convection changes in part the various

traditional baking notions. When roasting meat it is not necessary to turn the meat any more and for a roast on the spit, it is not

indispensable to use the spit-roaster, but is sufficient to put the meat directly on the grate.

With the use of the fan gas oven, the baking temperatures are slightly lower of about 10-15°C compared to those in use with the

traditional gas oven. The fan operation of the oven prevents the operation of the grill, which therefore cannot be used with the

fan in action.

The oven can also be used in a traditional way, (by not activating the fan) for foods requiring heat from the bottom, e.g. pizza.

WARNING: If the burner flames are extinguished accidentally, turn off the control knob and do not try to relight the

oven until after at least 1 minute.

TABLE n° 8

POSITION OF OVEN KNOB ONLY OVEN BURNER OVEN BURNER+GRILL BURNER

1=MINIMUM 120°C 200°C

8=MAXIMUM 220°C 270°C

The oven burner can be ignited in different ways:

- Manual lighting (it is always possible even when the power is cut off):

To light the oven, open the oven door and turn the knob so the no. 8 on the scale matches the indicator (Fig.31). At the same

time put a lit match next to the ignition tube that is visible on the oven level (fig.32). Then press the thermostat knob (this makes

the gas start to flow) and keep it pressed, after the burner has been completely lit, for 10 seconds. Release the knob and make

sure that the burner remains on, otherwise repeat the operation.

- Electric ignition (only for the models equipped with this device):

In this case, first open the oven door, then press and turn the knob to the maximum temperature setting (number 8). Then press

the thermostat knob (models with ignition trough knob). Wait about 10 seconds after the burner has been completely lit and then

release the knob. Make sure that the burner remains on, otherwise repeat the operation. As for cookers without ignition trough

knob, press the thermostat knob and the key with the spark symbol, wait about 10 seconds after the burner has been

completely lit and then release the knob. Make sure that the burner remains on, otherwise repeat the operation.

The ignition device should not be used for more than 15 seconds. If after that period the burner still has not been lit, do

not use the device and open the door of the room or wait at least 60 seconds before trying to light the oven again.

WARNING: afther lighting the oven and grill burners, please wait for 2 or 3 minutes before closing the oven door, in

order to allow the burners flamesto became stable

WARNING: when trying to light the oven, the door must always be open. When using the oven, leave the cooker cover

open to prevent it from overheating.

NOTICE: when using the oven for the first time it should be operated for 15-30 minutes at a temperature of about 250°

without cooking anything inside in order to eliminate any moisture and odours from the internal insulation.

During normal oven use, after lighting the burner and setting the desired temperature, wait about 15 minutes before putting in

any food to preheat the oven. The oven is equipped with 5 guides at different heights (fig.33) which can be used to insert

shelves or the tray. To keep the oven as clean as possible it is recommended to cook meat on the tray or on the shelf that has

been inserted inside the tray.

USING THE CHANGE-OVER SWITCH (Fig. 34-35-36 )

The 2+0 change-over switch used for gas oven models.

the symbol and is for oven fan and light operation;

the symbol and is for oven turnspit and light operation;

the symbol is for turning on the oven light.

USING THE ELECTRIC THERMOSTAT (fig.36 )( WITH A MULTIFUNCTION OVEN)

The thermostat supplied with the relative models maintains a constant temperature inside the oven at a specific temperature

setting ranging from 50°C to 250°C.

Turn the knob clockwise and align the selected temperature indicated on the ring with the index etched on the control panel.

Thermostat operation is indicated by an orange light which will turn off when the temperature inside the oven is 10°C greater

than the temperature setting, and will turn on when the oven is 10°C less than the temperature setting. The thermostat can

control the oven elements only if the relative switch is in one of the possible oven element operating modes: if the switch is in

position 0, the thermostat has not effect on the oven elements, which remain off.

USING THE MULTIFUNCTION OVEN (fig.37)

Before using the ovens for the first time:

- Remove all packaging and accessories from inside the ovens.

- Heat the ovens to 200°C for ½ hour to burn off

manufacturing residues.

- The automatic programmer must be set to Manual mode for ordinary cooking.

- The oven will not function when set in Automatic mode. See pag. 18-19.

To use the ovens:

Turn the function selector knob (Fig.37) clockwise to the desired function.

The orange light will illuminate, indicating that the element is on.

Turn the temperature selector knob (Fig.36B )clockwise to the desired temperature. The orange light will go out once the

oven has reached temperature and is ready for use. It is normal for this light to go on and off during cooking as the elements

maintain the temperature.

To turn the oven off

turn the function selector and temperature knobs anti- clockwise back to •.

Steam may be generated when cooking. As a precaution, always open the door in two stages. First, partially open the door by

100mm for a few seconds to allow the steam to escape, then open the door fully. Keep your face and head away from the door

when opening.

Never line the oven interior with foil as this can cause overheating and damage the enamel. Never cook on the oven base.

Always place dishes and trays onto an oven shelf. Do not leave the grill pan or other dishes on the oven base as damage to

the oven may occur.

Preheating the oven:

'Quickstart' provides the most efficient and fastest way to preheat the main oven (left hand oven). It will also ensure your oven

cooks evenly. Use 'Quickstart' as follows (

Select 'Quickstart' (using the oven function selector) and the required cooking temperature (using the temperature selector).

Allow the orange thermostat light to come on and off several times. This allows the temperature to stabilize before introducing

food .

2 Select the recurred cooking function and place the food in the oven.

3 When preparing heat sensitive foods such as cakes or meringues using the 'True Fan' function, allow the orange light to come

on and off

again several times to allow the top element to cool slightly.

'Quickstart' is unsuitable for use as a cooking function It is a quick pre-heat system.

OVEN FUNCTIONS

When using any of the functions in the multifunction oven (except grilling and defrosting) it is always recommended that you pre-

heat the oven using the Quick start function, before switching over to your desired cooking function.

When using the Fan Assisted or True Fan oven function, it is advisable to reduce the oven temperature by 20°C if following a

recipe written for a conventional oven. Check the food often through the latter stages of cooking until you are used to the

cooking times and temperatures.

The ovens have a range of cooking functions providing different heat zones

The 'True Fan' function for instance, is most

suitable for cakes

desserts and batch baking. The

Fan Assisted

function gives more browning so is more suitable for roasting

meats and vegetables or frozen potato products.

Example: To cook a turkey:

When cooking a turkey, the grill pan can be used as a roasting

tin

Line the pan with a double layer of extra wide foil, allowing

enough foil to wrap the turkey loosely. It

important to allow enough space around the sides and top of the oven for the hot air

to circulate. Make sure that the foil is not touching the sides or top of the oven. In a 60cm oven a turkey of

to 11 kg can be

cooked. In a 40cm oven a turkey of 6 – 9 kg can be cooked.

The oven light operates on selection of any oven function

Symbol Function What to use it fo

Quickstar

Defrost

It is recommended that the oven is always pre-heated before use, whatever the cooking

temperature. Quick start is not suitable for cooking - once the oven has reached

temperature, switch to one of the oven functions below.

Place small frozen items on an oven tray at the lowest shelf position, and set the

temperature selector knob to O°C. Never use heat to defrost as this can pose a health risk.

Larger items such as joints, or a whole chicken or turkey, should be defrosted in the

refrigerator.

Conventional oven

Ideal for roasting and for baking items such as bread or rich fruit cakes on a single shelf.

Lower element

Use at low temperatures for slow-cooking casseroles, custard

or for warming plates. Use at high temperatures for cooking sweet and savoury pastry tarts.

Upper element

Use for browning and reheating dishes such as lasagne, moussaka and cauliflower cheese.

Conventional grill

Ideal for crumpets, muffins and Welsh rarebit. Use when grilling for less than 15mins. For

foods needing a longer time use fan assisted grilling.

Fan assisted grill

The fan circulates hot air around the food helping to cook it all the way through. Ideal for

cooking meat such as sausages and chicken portions. Cooking high water content foods

such as bacon and chops with this function helps to reduce condensation. (Recommended:

Door closed 200°C, 2nd from top shelf, turn the food over halfway through.

Fan assisted oven

The fan circulates the hot air around the oven for uniform cooking of larger quantities of

food. Use for roasting vegetables, meat and poultry, or baked fish. This function is the best

one for cooking frozen potato products and breaded/battered chicken or fish.

True fan oven

This function is suitable for most recipes and is an efficient way to cook. The temperature is

kept uniform throughout the oven and is particularly suitable for baking on several shelves

or for batch cooking.

Pizza

Use for cooking pizza

pastry or flat breads to get a

perfectly cooked base.

Using the grill

The grill pan consists of a wire trivet and enamel tray. Place food on the wire trivet. A lower shelf position can be used to slow

cooking down, or the temperature can be reduced. A detachable grill pan handle is supplied for removing the hot tray.

Both the Fan Assisted Grill and Conventional Grill functions are designed to be used with the oven door closed. This ensures

efficient preheating and even cooking.

When grilling, always pre-heat the grill element for 5 minutes before introducing food (200°C is recommended for preheating). It

is recommended that the grill pan is always removed from the oven when not in use, as air flow around the oven can be

impaired. The grill should be used with the oven door closed. Use the Fan Assisted Grill function for thicker pieces of meat and

when cooking high water content foods to reduce condensation.

Always use oven gloves when handling the grill pan and turning food. Do not line the grill pan with aluminium foil, this can cause

damage to the enamel coating and the grill elements.

At the end of

cooking remove the grill pan for cleaning. If high fat content foods have been prepared, leave the grill turned on at

a maximum temperature for 5 minutes to clean the grill element.

USING THE NATURAL CONVENTIONAL ELECTRIC OVEN

When using the oven for the first time it should be operated for a maximum of 30 minutes at a temperature of about 250° to

eliminate any odours generated by the internal insulation. During normal oven use, select the desired cooking temperature

using the thermostat knob and wait until the orange light turns off before putting in any food. The oven is equipped with 5 guides

at different heights (fig.33) which can be used to insert shelves or the tray. To keep the oven as clean as possible it is

recommended to cook meat on the tray or on the shelf that has been inserted inside the tray. Personal experience will help to

determine any variations in the values reported in the table. In any case, it is recommended to follow the instructions of the

specific recipe being used.

USING THE VENTILATED ELECTRIC OVEN

When using the oven for the first time it should be operated for a maximum of 30 minutes at a temperature of about 250° to

eliminate any odours generated by the internal insulation.

Before cooking, allow the oven to reach the desired temperature setting waiting for the orange light to turn off. This type of oven

is equipped with a circular element around which a fan has been installed that creates forced-air circulation in the horizontal

direction. Thanks to this type of operation, the ventilated oven can be used for different types of cooking at the same time,

without changing the taste of each food. Only some models are equipped with a removable metallic filter applied to the rear

screen which collects the fat while a roast is cooking. Therefore, it is recommended to remove this fat periodically, washing the

screen with soapy water and rinsing thoroughly. To remove the metallic filter just apply slight pressure toward the top on the tab

indicated by the arrow. Hot-air circulation guarantees a uniform distribution of heat. Pre-heating the oven is not necessary, but

for very delicate pastries, it is recommended to heat the oven before inserting the trays.

The ventilated conventional system partially changes the various notions about traditional cooking. Meat no longer needs to be

turned while it is cooking and the rotisserie is no longer needed to cook a roast on the spit. Just put the meat directly on the

shelf.

USING THE GAS GRILL (SINGLE CONTROL)

The gas grill can be combined only with the gas oven. It is controlled with the same gas oven knob (Fig.30), but turning it

clockwise instead of counterclockwise (see the gas oven use instructions), matching the symbol with the indicator. The grill

burner always operates at maximum and therefore there is no minimum position. In addition, it is equipped with a safety device

to prevent the flame from going out. The gas grill can also be ignited in different ways:

- Manual lighting: Just completely open the oven door, turn the knob so that the relative symbol matches the indicator, while

pressing the knob, and, at the same time, put a lit match next to the burner. Make sure that the burner is completely lit and after

about 10 seconds release the knob. Make sure that the burner remains on, otherwise repeat the operation.

- Electric ignition: In this case, completely open the oven door, press and turn the knob so that the relative symbol matches the

indicator, then press the thermostat knob (models with ignition trough knob). Wait about 10 seconds after the burner has been

completely lit and then release the knob. Make sure that the burner remains on, otherwise repeat the operation. As for cookers

without ignition trough knob, press the thermostat knob and the key with the spark symbol, wait about 10 seconds after the

burner has been completely lit and then release the knob. Make sure that the burner remains on, otherwise repeat the

operation.

WARNING: As with the oven, the grill must be lit with the door completely open.

The gas grill can be used to grill foods on the oven shelf or using the rotisserie.

Grilling on the shelf: In this case, the shelf supplied is placed on level 1 or 2 and the foods to be grilled are placed on top,

while the tray is inserted on the lower levels to collect the cooking juices.

Then light the grill burner according to the instructions described above.

IMPORTANT: grill foods on the shelf always with the door close.

WARNING: the accessible parts may become very hot while grilling. Keep children away from the appliance while

cooking.

Grilling with the rotisserie: This is used to grill with the rotating skewer. Therefore, insert the skewer holder on the side

shelves at level 3. Insert the food on the skewer and insert everything into the oven, inserting the point of the skewer into the

spindle that projects out from the left side of the oven and resting the front of the skewer into the skewer holder support (fig.38).

Afther, insert the tray into one of the lower guides, then light the grill burner according to the instructions described above and

press the button that starts the rotisserie

IMPORTANT: grill foods with the rotisserie always with the door close.

WARNING: the accessible parts may become very hot while grilling. Keep children away from the appliance while

cooking.

USING THE GAS GRILL FOR MODEL WITH DOUBLE CONTROLS

Oven and grill burners should not be used simultaneously

The gas grill can be combined only with the gas oven.

A diagram is etched on the control panel above each knob which indicates which burner corresponds to that knob. The gas grill

can be ignited in different ways depending on the type of appliance and its specific characteristics:

- Manual lighting (it is always possible even when the power is cut off): Just completely open the oven door, turn the knob

counterclockwise that corresponds to the gas grill, setting it to the MAXIMUM position at the etched star (large flame Fig.15)

while keeping the knob pressed and place a lit match up to the burner. Make sure that the burner is completely lit and after

about 10 seconds release the knob. Make sure that the burner remains on, otherwise repeat the operation.

- Electric ignition: In this case, completely open the oven door, press and turn the knob so that the relative symbol matches the

indicator, then press the thermostat knob (models with ignition trough knob). Wait about 10 seconds after the burner has been

completely lit and then release the knob. Make sure that the burner remains on, otherwise repeat the operation. As for cookers

without ignition trough knob, press the thermostat knob and the key with the spark symbol, wait about 10 seconds after the

burner has been completely lit and then release the knob. Make sure that the burner remains on, otherwise repeat the

operation.

WARNING: afther lighting the oven and grill burners, please wait for 2 or 3 minutes before closing the oven door, in

order to allow the burners flamesto became stable