Simplicity 030794-00 Manuel utilisateur

Marque: Simplicity

Modèle: 030794-00

Catégorie: Groupes électrogènes

Taper: Manuel utilisateur

Not for

Reproduction

Manual No. 80081451 Revision A

Outdoor Portable Generator

Operator’s Manual

Model Number _____________________________

Revision __________________________________

Serial Number ______________________________

Date Purchased ____________________________

Oregon® is a registered trademark of Blount, Inc. in the United

States and other countries. Used under license.

Not for

Reproduction

2 www.oregonproducts.com

Equipment Description

Table of Contents

Equipment Description.........................2

Features and Controls .........................5

Operation....................................8

Maintenance ................................13

Storage ....................................16

FCC/IC Compliance Statement .................16

Troubleshooting/Specifications .................17

Warranty ...................................20

Symbols and Meanings

Signal Meaning

DANGER

Indicates a hazard which, if not avoided, will

result in death or serious injury.

WARNING

Indicates a hazard which, if not avoided, could

result in death or serious injury.

CAUTION

Indicates a hazard which, if not avoided, could

result in minor or moderate injury.

NOTICE

Indicates information considered important, but

not hazard-related.

Symbol Name Explanation

Safety Alert

Symbol

Indicates a potential personal injury

hazard.

Operator’s

Manual

Failure to follow warnings,

instructions and operator’s manual

could result in death or serious

injury.

Toxic Fumes

Engine exhaust contains carbon

monoxide, a poisonous gas that

will kill you in minutes. You cannot

smell it or see it.

Fire

Fuel and its vapors are extremely

flammable which could cause

burns or fire resulting in death or

serious injury.

Engine exhaust could cause fire

resulting in death or serious injury.

Electric

Shock

Generator could cause electrical

shock resulting in death or serious

injury.

Hot Surface

Muffler could cause burns or

resulting in serious injury.

WARNING! This product can expose you to chemicals

including gasoline engine exhaust, which is known to

the State of California to cause cancer, and carbon

monoxide, which is known to the State of California to cause birth

defects or other reproductive harm. For more information go to

www.P65Warnings.ca.gov.

Equipment Description

Read this manual carefully and become familiar

with your outdoor generator. Know its applications,

its limitations, and any hazards involved. Save

these instructions for future reference.

The outdoor generator is an engine-driven, revolving field,

alternating current (AC) generator equipped with a voltage

regulator. The generator is designed to supply electrical power

for operating compatible electrical lighting, appliances, tools

and motor loads. The voltage regulator within the generator is

designed to automatically maintain output voltage level.

The portable generator can be used to power outdoor items

using the extension cords or to restore home power using a

transfer switch. A transfer switch is a separate device installed

by a licensed electrician that allows the portable generator to be

cord connected, using the locking receptacle, directly into your

home’s electrical system. Install a listed transfer switch as soon

as possible if generator will be used to provide home power

restoration.

Every effort has been made to ensure that the information in this

manual is both accurate and current. However, the manufacturer

reserves the right to change, alter or otherwise improve the

generator and this documentation at any time without prior notice.

NOTICE If you have questions about intended use, contact an

authorized service dealer. This equipment is designed to be used

with Briggs & Stratton® authorized parts only.

This spark ignition system complies with the Canadian

standard CAN ICES-2/NMB-2.

System Ground

The generator has a system ground that connects the generator

frame components to the ground terminals on the AC output

receptacles. The system ground is connected to the AC neutral

wire (the neutral is bonded to the generator frame).

Special Requirements

There may be Federal or State regulations, local codes, or

ordinances that apply to the intended use of the generator.

Please consult a qualified electrician,

electrical inspector, or

the local agency having jurisdiction.

This generator is not intended to be used at a construction

site or similar activity as defined by NFPA 70-2017 (NEC)

section 590.6.

Not for

Reproduction

To Restore Home Power Using a Listed

Transfer Switch

Connections to your home’s electrical system must use a

listed* transfer switch installed by a licensed electrician.

The connection must isolate the generator power from

the utility power and comply with all applicable laws and

electrical codes. Power your home with a 30 Amp transfer

switch system.

120/240V

Outlet

—

Transfer

Switch

Typical Indoor Items

To Restore Power Using Extension Cords

1. Only use grounded cords marked for outdoor use

rated for your loads.

To provide power using

extension cords

Total

Amperage

Minimum Gauge, Outdoor Rated

Up to 50 FT (15 M) Up to 100 FT (30 M)

Up to 13A

Up to 15A

Up to 20A

Up to 30A

2. Follow cord safety instructions.

3. Install carbon monoxide alarm(s).

4. When operating generator with extension cords, make

sure it is located in an open, outdoor area, at least 20

ft. (6.1 m.) from occupied spaces with exhaust pointed

away.

5. Extension cords running directly into home, powering

indoor items IS NOT RECOMMENDED.

DANGER! Engine exhaust contains carbon

monoxide, a poisonous gas that will kill you in

minutes. You cannot smell it, see it, or taste it.

Even if you do not smell exhaust fumes, you could still be

exposed to carbon monoxide gas.

• Extension cords running directly into the home

increase your risk of carbon monoxide poisoning

through openings.

• If an extension cord running directly into the home is

used to power indoor items, the operator recognizes

that this increases the risk of CO poisoning to people

inside the home and assumes that risk.

6. Install a listed* transfer switch as soon as possible

if generator will be used to provide home power

restoration.

Equipment Description

120V

OUTLET

* Certified by a Nationally Recognized Testing Laboratory that the

product complies to appropriate product safety test standards.

Not for

Reproduction

4 www.oregonproducts.com

Equipment Description

Air Cleaner — Filters engine intake air.

Choke Lever — Used when starting a cold engine.

Engine Identification — Provides model, type and code of

engine.

Fuel Cap — Add unleaded fuel here.

Fuel Valve — Used to turn fuel supply on and off to engine.

Grounding Fastener — Consult your local agency having

jurisdiction for grounding requirements in your area.

Identification Label — Provides model and serial number of

generator.

Oil Drain Plug — Drain engine oil here.

Oil Fill Cap/Dipstick — Check and add engine oil here.

Recoil Starter — Used to start the engine manually.

Spark Arrester Muffler/Exhaust — Exhaust muffler lowers

engine noise and is equipped with a spark arrester screen.

Engine Identification

Oil Fill Cap/Dipstick

Oil Drain Plug

Fuel Cap

Grounding Fastener

Choke Lever

Spark Arrester Muffler/Exhaust

Air Cleaner

Identification Label

Fuel Valve

Recoil Starter

Not for

Reproduction

Features and Controls

120 Volt AC, 20 Amp, GFCI Duplex Receptacles — Used

to supply 120 Volt AC, single phase, 60 Hz power for

electrical lighting, appliance, tool and motor loads.

120/240 Volt AC, 30 Amp Locking Receptacle — Used to

supply 120 / 240 Volt AC, single phase, 60 Hz power for

electrical lighting, appliance, tool and motor loads.

Circuit Breakers (AC) — The 120 Volt AC, 20A GFCI

duplex receptacles are provided with “push to reset” 20

Amp circuit breakers to protect the generator against

electrical overload.

CO Guard™ Carbon Monoxide (CO) Shutdown Indicator

Light — Indicates the engine shutdown due to carbon

monoxide accumulation around the generator or a CO

Guard system fault occurred.

Low Oil Shutdown — This unit is equipped with a low oil

protection device. Oil must be at proper level for engine

to run. If the engine oil drops below a preset level, an oil

switch will stop the engine. Check oil level with dipstick.

Main Breaker — The receptacles are provided with a

27 Amp rocker switch main circuit breaker to protect the

generator against electrical overload.

Start Switch — Turn key to START position to start engine.

Turn key to OFF position to switch off engine.

Compare the illustrations with your generator to familiarize yourself with the locations of various controls and product warnings.

Main Breaker

120/240 Volt AC, 30 Amp

Locking Receptacle

120 Volt AC, 20 Amp

GFCI Duplex Receptacles

Circuit Breakers

Low Oil

Shutdown

Start Switch

CO Guard™ Carbon

Monoxide (CO)

Shutdown Indicator Light

Not for

Reproduction

6 www.oregonproducts.com

Features and Controls

Not for

Reproduction

Features and Controls

Exhaust/muffler

Point away from home

Not for

Reproduction

8 www.oregonproducts.com

Operation

Step 1: Safe Location

Before starting the portable generator there are two equally

important safety concerns regarding carbon monoxide

poisoning and fire that must be addressed.

Operation Location to Reduce the Risk of

Carbon Monoxide Poisoning

The engine exhaust of all fossil fuel burning equipment,

such as a portable generator, contains carbon monoxide,

a poisonous gas that will kill you in minutes. You cannot

smell it, see it, or taste it. Even if you do not smell exhaust

fumes, you could still be exposed to carbon monoxide gas.

By law in many jurisdictions it is required to have a carbon

monoxide alarm in operating condition in your home.

A carbon monoxide alarm is an electronic device that

detects hazardous levels of carbon monoxide. When there

is a buildup of carbon monoxide, the alarm will alert the

occupants by flashing visual indicator light and alarm.

Smoke alarms cannot detect carbon monoxide gas.

DANGER! Engine exhaust contains carbon

monoxide, a poisonous gas that will kill you in

minutes. You cannot smell it, see it, or taste it.

Even if you do not smell exhaust fumes, you could still be

exposed to carbon monoxide gas.

• Operate portable generator only outdoors, at least

20 ft. (6.1 m) from occupied spaces with exhaust

pointed away to reduce the risk of carbon monoxide

accumulating.

• Install battery-operated carbon monoxide alarms or

plug-in carbon monoxide alarms with battery back-up

according to the manufacturer’s instructions. Smoke

alarms cannot detect carbon monoxide gas.

• Do not run portable generator inside homes, garages,

basements, crawlspaces, sheds, or other partially-

enclosed spaces even if using fans or opening doors

and windows for ventilation. Carbon monoxide can

quickly build up in these spaces and can linger for

hours, even after this product has shut off.

If you start to feel sick, dizzy, weak, or your homes carbon

monoxide alarm sounds while using this product, get to

fresh air right away. Call emergency services. You may

have carbon monoxide poisoning.

Carbon Monoxide Alarm(s)

Install carbon monoxide alarm

inside your home. Without

working carbon monoxide

alarms, you will not realize you

are getting sick and dying from

carbon monoxide poisoning.

To better educate yourself about all carbon monoxide risks,

go to www.takeyourgeneratoroutside.com.

Prevent Carbon Monoxide (CO) Poisoning

• Use outdoors at least 20 ft. (6.1 m) from any home.

• Point exhaust away from all homes and occupied spaces.

• Install CO alarms inside your home.

20 ft. (6.1 m) min.

Not for

Reproduction

Operation

Operation Location to Reduce the Risk of Fire

WARNING!

Exhaust heat/gases could ignite

combustibles, structures or damage fuel tank

causing a fire, resulting in death or serious injury.

• Portable generator must be at least 5 ft. (1.5 m) from any

structure, overhang, trees, shrubs, or vegetation over 12

in. (30.5 cm) in height.

• Do not place portable generator under a deck or other

type of structure that may confine airflow. Smoke alarm(s)

must be installed and maintained indoors according to the

manufacturer’s instructions/recommendations.

• Carbon monoxide alarms cannot detect smoke.

• Do not place portable generator in manner other than

shown.

MUFFLER

5 ft. (1.5 m)

min.

5 ft. (1.5 m)

min.

20 ft. (6.1 m) min.

Not for

Reproduction

10 www.oregonproducts.com

Operation

Step 2: Oil and Fuel

Fuel must meet these requirements:

• Clean, fresh, unleaded fuel with a minimum of 87 octane.

• Gasoline with an ethanol content up to 10% is acceptable.

E10

E15

NOTICE Do not mix oil in fuel or modify engine to run on

alternate fuels. Use of unapproved fuels could damage

engine and will not be covered under warranty.

See High Altitude for 5,000 ft. and above.

WARNING! Fuel and its vapors are extremely

flammable which could cause burns or fire

resulting in death or serious injury.

• Do not refuel during operation.

• Do not smoke during refueling.

• Turn engine off and let it cool at least 2 minutes before

removing fuel cap.

• Fill fuel tank outdoors. Keep fuel away from sparks, open

flames, pilot lights, heat, and other ignition sources.

Check fuel lines, tank, cap and fittings frequently for

cracks or leaks. Replace if necessary.

1. Move generator outdoors to a flat, level surface.

2. Clean area around oil fill and remove oil fill cap/dipstick.

3. Slowly pour contents of oil bottle into oil fill opening.

Checking oil level frequently, fill to full mark on dipstick.

NOTICE DO NOT screw in dipstick when checking oil level.

NOTICE Pause to permit oil to settle. Wipe dipstick clean

each time oil level is checked. DO NOT overfill.

4. Replace and fully tighten oil fill cap/dipstick.

5. Slowly remove fuel cap to relieve pressure in tank.

6. Slowly add unleaded fuel to fuel tank. Be careful not

to fill above bottom lip. This allows adequate space for

fuel expansion.

7. Install fuel cap and let any spilled fuel evaporate

before starting engine.

High Altitude

At altitudes over 5,000 ft. (1524 m), a minimum 85 octane

fuel is acceptable. To remain emissions compliant, high

altitude adjustment is required. Operation without this

adjustment will cause decreased performance, increased

fuel consumption,

and increased emissions.

See an authorized Briggs & Stratton dealer for high altitude

adjustment information. Operation of the engine at altitudes below

2,500 ft. (762 m) with the high altitude kit is not recommended.

Transporting

When transporting equipment with a vehicle or trailer, turn fuel

shutoff valve to off (0) position. Do not tip engine or equipment at

an angle which causes fuel to spill.

Step 3: Generator Start Up

Disconnect all electrical loads from the generator. Use the

following start instructions:

1. Make sure unit is outdoors on a level surface.

NOTICE Failure to operate the unit on a level surface may

cause the unit to shut down.

2. Turn the fuel valve to the on (I) position.

3. Push choke lever to choke ( ) position.

4. Turn and hold key in start switch to START position

until generator starts. DO NOT hold key in START

position for more than 5 seconds. Pause for at least

30 seconds between starting attempts.

Fuel Valve

Start

Switch

Choke Lever

Full

Not for

Reproduction

NOTICE If battery is discharged, turn key in start switch

to RUN position, grasp recoil handle and pull slowly until

slight resistance is felt. Then pull rapidly one time only to

start engine.

5. Slowly move choke lever to run (

) position. If engine

falters, move choke lever to half choke position until

engine runs smoothly, and then to run ( ) position.

NOTICE If engine starts but fails to run, see Low Oil

Shutdown in Features and Controls.

Step 4: Connecting Electrical Loads

Using Extension Cords

Use only grounded extension cords marked for outdoor

use rated for your loads. Follow cord safety instructions.

WARNING! Damaged or overloaded extension

cords could overheat, arc, and burn resulting in

death or serious injury.

NOTICE For best results when plugging into the 120 Volt

receptacles, plug items to be powered in sequence as

shown.

NOTICE For generator output required see Generator

Capacity. Connect electrical loads in off position then turn

on for operation.

120 Volt AC, 20 Amp, GFCI Duplex Receptacles

Use each receptacle to operate 120 Volt AC, single-phase,

60 Hz electrical loads requiring up to 2,400 Watts (2.4 kW)

at 20 Amps of current.

Ground Fault Protection

The duplex receptacles are equipped with Ground Fault

Circuit Interrupter (GFCI) protection. The GFCI protects

against electrical shock that may be caused if your body

becomes a path which electricity travels to reach ground.

When protected by a GFCI, one may still feel a shock, but

the GFCI is intended to cut current off quickly enough so

that a person in normal health should not suffer any serious

electrical injury.

WARNING! Generator voltage could cause

electrical shock or burn resulting in death or

serious injury. Contact with the hot and neutral

conductor at the same time could cause electrical shock

or burn, even if the circuit is GFCI protected.

Testing the GFCI

Test your GFCI outlet prior to each use, as follows:

• Push the “Test” button. The “Reset” button should pop

out, which should allow no power to reach the outlet.

• Press the “Reset” button firmly until it is fully in place

and locks in that position. If the GFCI outlet does not

reset properly, do not use the outlet. Call or take your

generator to a local service center.

• If the GFCI trips by itself at any time, reset and test the

outlet.

120/240 Volt AC, 30 Amp, Locking Receptacle

Use a NEMA L14-30 plug with this receptacle. Connect a

4-wire cord set rated for 250 Volt AC loads at 30 Amps. The

generator’s locking receptacle is not protected by a GFCI.

This receptacle powers 120/240 Volt AC, 60 Hz, single

phase loads requiring up to 6,500 Watts of power (6.5 kW)

at 27 Amps for 240 Volts or two independent 120 Volt

loads at 27 Amps each.

Operation

4-Wire Cord Set

240V

120V

W (Neutral)

X (Hot)

Y (Hot)

Ground (Green)

120V

NEMA L14-30

Not for

Reproduction

12 www.oregonproducts.com

Operation

Generator Capacity

To make sure your generator can supply enough running

watts and starting watts for the items you will power at the

same time, follow these simple steps:

1. Select the items you will power at the same time. See

following list for typical wattages.

* Typical wattages listed are approximate only. Check tool

or appliance for actual wattage.

** Per Briggs & Stratton 628K, Starting Watts represents

the momentary electrical current the generator can

provide to start electric motors. Starting Watts does

not represent the power required to continuously run

electrical loads. Starting Watts is the maximum current

that can momentarily be supplied when starting a motor,

multiplied by the generator’s rated voltage.

2. Total the running watts. This is the amount of power

your generator must produce to keep your items

running. See following example:

Example

Total running watts = 2355

Highest starting watts = 2000

Total generator watts required = 4355

3. Estimate the starting watts you will need. Because not

all motors start at the same time, total starting wattage

can be estimated by adding only the item with the

highest additional starting watts requirements to the

total running watts from step 2.

Power Management

To manage generator power, sequentially add loads as

follows:

1. With nothing connected to generator, start the engine

outdoors.

2. Plug in and turn on the first load, preferably the largest

load you have.

3. Permit the generator output to stabilize (engine runs

smoothly and attached device operates properly).

4. Plug in and turn on the next load.

5. Again, permit the generator to stabilize.

6. Repeat steps 4 and 5 for each additional load.

Never add more loads than the generator capacity. Take

special care to consider surge loads in generator capacity.

CO Guard

Carbon Monoxide (CO) Shutdown System

CO Guard automatically shuts down the engine when

harmful levels of carbon monoxide accumulate around the

generator or a CO Guard fault occurs. After shutdown, the

CO Guard indicator light will blink for at least five minutes

per the chart below.

CO Guard DOES NOT replace carbon monoxide alarms.

Install battery-powered carbon monoxide alarm(s) in your

home. Do not run generator in enclosed areas.

Color/Pattern Description

Red

•• ••

Carbon monoxide accumulated around

generator. Move generator to an

open, outdoor area 20 ft. (6.1 m) from

occupied spaces with exhaust pointed

away. Automatic shutoff is an indication

generator was improperly located. Air

out premises (e.g. open windows and

doors) before reoccupying.

If you start to feel sick, dizzy, weak, or

your homes carbon monoxide alarm

sounds while using this product, get to

fresh air right away. Call emergency

services. You may have carbon

monoxide poisoning.

Blue

• • •

CO Guard fault occured

See Briggs & Stratton authorized service

dealer.

Blue light will blink for five seconds at the startup of generator to

show CO Guard functioning properly.

Step 5: Generator Shutdown

1. Turn off and unplug all electrical loads from generator

panel receptacles. Never stop engine with electrical

devices plugged in and turned on.

2. Let engine run at no-load for one minute to stabilize

internal temperatures of engine and generator.

3. Turn key in start switch to 0FF position.

4. Move fuel valve to off (0) position.

Tool or Appliance Running Watts Starting Watts

Window air conditioner

1200 1800

Refrigerator 800 2000

Television 280 —

Light (75 Watts) 75 —

2355 Total

Running Watts

2000 Highest

Starting Watts

Tool or Appliance

Running

Watts*

Starting

Watts**

Light Bulb - 75 Watt 75 -

Sump Pump 800 1200

Refrigerator/Freezer 800 2000

Water Well Pump - 1/3 HP 1000 2000

Window AC - 10,000 BTU 1200 1800

Furnace Fan Blower - 1/2 HP 800 1300

Microwave Oven - 1000 Watt 1000 -

Color Television - 42” 280 -

Personal Computer w/17” monitor 800 -

Garage Door Opener - 1/2 HP 480 520

Not for

Reproduction

Maintenance

Maintenance Schedule

Follow the hourly or calendar intervals, whichever occurs

first. More frequent service is required when operating in

adverse conditions noted below.

Service more often under dirty or dusty conditions.

General Recommendations

Regular maintenance will improve the performance and

extend the life of the generator. See any authorized dealer

for service.

The generator’s warranty does not cover items that have

been subjected to operator abuse or negligence. To

receive full value from the warranty, the operator must

maintain the generator as instructed in this manual.

All service and adjustments should be made at least once

each season. A new spark plug and clean air filter assure

proper fuel-air mixture and help your engine run better and

last longer. Follow requirements in Maintenance Schedule.

Emissions Control

Maintenance, replacement, or repair of the emissions

control devices and systems may be performed by any

non-road engine repair establishment or individual.

However, to obtain ”no charge” emissions control service,

the work must be performed by a factory authorized dealer.

See Emissions Warranty.

Cleaning

Daily or before use, look around and underneath

the generator for signs of oil or fuel leaks. Clean any

accumulated debris. Keep area around muffler free from

any debris.

• Use a soft bristle brush to loosen caked on dirt or oil.

• Use a damp cloth to wipe exterior surfaces clean.

NOTICE Improper treatment of generator could damage

it and shorten its life. Do not expose generator to excessive

moisture, dust, dirt, or corrosive vapors. Do not insert any

objects through cooling slots.

Fuel Valve Maintenance

The fuel valve is equipped with a fuel sediment cup,

screen, and o-ring that need to be cleaned.

1. Move fuel valve to off (0) position.

2. Remove sediment cup from fuel valve. Remove o-ring

and screen from fuel valve.

3. Wash sediment cup, o-ring, and screen in a

nonflammable solvent. Dry them thoroughly.

4. Place screen and o-ring into fuel valve. Install

sediment cup and tighten securely.

5. Move fuel valve to on (I) position, and check for leaks.

Replace fuel valve if there is any leakage.

Battery Maintenance

Other than charging, no maintenance is required for the

starting battery. Keep the battery and terminals clean and

dry.

NOTICE Battery charging should be performed in a dry

location.

Screen

O-Ring

Sediment Cup

First 5 Hours

• Change engine oil

Every 8 Hours or Daily

• Clean debris

• Check engine oil level

Every 50 Hours or every season

• Clean/Replace air filter

Every 100 Hours or every season

• Change oil

• Change/Adjust spark plug

• Clean spark arrester

• Service fuel valve

Not for

Reproduction

14 www.oregonproducts.com

Maintenance

Engine Maintenance

Oil Recommendations

We recommend the use of Briggs & Stratton Warranty

Certified oils for best performance. Other high-quality

detergent oils are acceptable if classified for service SF,

SG, SH, SJ or higher. Do not use special additives.

Outdoor temperatures determine the proper oil viscosity

for the engine. Use the chart to select the best viscosity for

the outdoor temperature range expected. Engines on most

outdoor power equipment operate well with 5W30 Synthetic

oil. For equipment operated in hot temperatures, Vanguard®

15W50 Synthetic oil provides the best protection.

* Below 40°F (4°C) the use of SAE 30 will result in hard starting.

** Above 80°F (27°F) the use of 10W30 may cause increased oil

consumption. Check oil level more frequently.

Checking/Adding Engine Oil

Oil level should be checked prior to each use or at least

every 8 hours of operation. Keep oil level maintained.

1. Make sure generator is on a level surface.

2. Clean area around oil fill, remove dipsitck and wipe

with clean cloth. Replace dipstick. Remove and check

oil level.

NOTICE Do not screw in dipstick when checking oil level.

3. Verify oil is at full mark on dipstick. Replace and

tighten dipstick.

4. If needed, slowly pour oil into oil fill opening to the full

mark on dipstick. Do not overfill.

NOTICE Overfilling with oil could cause the engine to not

start, or hard starting.

• Do not overfill.

• If over the full mark on dipstick, drain oil to reduce oil

level to full mark on dipstick.

5. Replace and tighten dipstick.

NOTICE Do not attempt to crank or start engine before

it has been properly serviced with recommended oil. This

could result in an engine failure.

CAUTION Avoid prolonged or repeated skin contact

with used motor oil. Used motor oil has been shown

to cause skin cancer in certain laboratory animals.

Thoroughly wash exposed areas with soap and water.

KEEP OUT OF REACH OF CHILDREN. DON’T

POLLUTE. CONSERVE RESOURCES. RETURN

USED OIL TO COLLECTION CENTERS.

Changing Engine Oil

If you are using your generator under extremely dirty or

dusty conditions, or in extremely hot weather, change the

oil more often.

Change the oil while the engine is still warm from running,

as follows:

1. Make sure unit is on a level surface.

2. Remove oil drain plug and drain oil completely into a

suitable container.

3. Reinstall oil drain plug and tighten securely. Remove

dipstick.

4. Slowly pour recommended oil (about 36 oz. (1.0 l))

into oil fill opening. Pause to permit oil to settle. Fill to

Full mark on dipstick.

5. Wipe dipstick clean each time oil level is checked. Do

not overfill.

6. Reinstall dipstick. Tighten cap securely.

7. Wipe up any spilled oil.

Service Air Cleaner

WARNING! Fuel and its vapors are extremely

flammable which could cause burns or fire

resulting in death or serious injury.

• Do not start and run engine with air filter removed.

Your engine will not run properly and may be damaged if

you run it with a dirty air cleaner. Clean or replace more

often if operating under dusty or dirty conditions.

NOTICE Do not use pressurized air to clean the filter.

Pressurized air can damage the filter.

Oil Drain Plug

Full

Not for

Reproduction

Maintenance

To service the air cleaner, follow these steps:

1. Unclamp latches that hold on the cover.

2. Remove cover and foam air filter.

3. Wash the foam air filter in liquid detergent and water.

Squeeze dry the foam air filter in a clean cloth.

NOTICE If the filter is excessively dirty, replace with a

new filter. See Common Service Parts.

4. Saturate the foam air filter with clean engine oil. To

remove the excess engine oil, squeeze the foam air

filter in a clean cloth.

5. Reinstall clean or new foam air filter.

6. Reinstall the air filter cover and re-clamp latches.

Service Spark Plug

Changing the spark plug will help your engine to start

easier and run better.

1. Clean area around spark plug.

2. Remove and inspect spark plug.

3. Replace spark plug if electrodes are pitted, burned

or porcelain is cracked. Use the recommended

replacement spark plug. See Common Service Parts.

4. Check electrode gap with wire feeler gauge and reset

spark plug gap to recommended gap if necessary

(see Specifications).

5. Install spark plug and tighten firmly.

Inspect Muffler and Spark Arrester

The engine exhaust muffler has a spark arrester screen.

Inspect the muffler for cracks, corrosion, or other damage.

Inspect spark arrester screen for damage or carbon

blockage. Clean if carbon blockage is found using brush

and commercial solvent or replace if damaged.

WARNING!

Contact with muffler area could

cause burns resulting in serious injury.

• Do not touch hot parts.

• It is a violation of California Public Resource Code,

Section 4442, to use or operate the engine on any forest-

covered, brush-covered, or grass-covered land unless

the exhaust system is equipped with a spark arrester, as

defined in Section 4442, maintained in effective working

order. Other states or federal jurisdictions may have

similar laws, reference Federal Regulation 36 CFR Part

261.52.

Clean or replace spark arrester as follows:

1. Remove two screws holding cover plate and remove

spark arrester screen from muffler.

2. Carefully remove carbon deposits from spark arrester

screen with a wire brush.

3. Replace screen if damaged. See Common Service

Parts.

4. Position spark arrester in muffler and attach cover

plate with two screws.

Common Service Parts

Air Cleaner .............................704928

Spark Plug .............................704948

Engine Oil Bottle ...............100005 or 100028

Synthetic Oil Bottle ......................100074

Latches

Filter

Cover

Muffler

Cover Plate

Spark Arrester

Screen

Screws

Not for

Reproduction

16 www.oregonproducts.com

Storage

If storing the unit for more than 30 days, use the following

guidelines to prepare it for storage.

Long Term Storage Instructions

1. Clean the generator as outlined in Cleaning.

2. Change engine oil while engine is still warm, drain oil

from crankcase. Refill with recommended grade. See

Changing Engine Oil.

3. Treat or drain fuel from generator as fuel can become

stale when stored over 30 days.

Stale fuel causes acid and gum deposits to form in the fuel

system or on essential carburetor parts. To keep fuel fresh,

use a fuel stabilizer.

There is no need to drain gasoline from the engine if a

fuel stabilizer is added according to instructions. Run the

engine for 2 minutes to circulate the stabilizer throughout

the fuel system before storage.

If gasoline in the engine has not been treated with a fuel

stabilizer, it must be drained into an approved container.

Run the engine until it stops from lack of fuel. The use of a

fuel stabilizer in the storage container is recommended to

maintain freshness.

WARNING!

Fuel and its vapors are extremely

flammable and explosive which could cause

burns, fire or explosion resulting in death or

serious injury.

• When storing fuel or equipment with fuel in tank, store

away from furnaces, stoves, water heaters, clothes dryers

or other appliances that have pilot light or other ignition

source because they could ignite fuel vapors.

• When draining fuel, turn generator engine off and let it

cool at least 2 minutes before removing fuel cap. Loosen

cap slowly to relieve pressure in tank. Drain fuel tank

outdoors. Keep fuel away from sparks, open flames, pilot

lights, heat, and other ignition sources.

• Check fuel lines, tank, cap and fittings frequently for

cracks or leaks. Replace if necessary.

4. Store generator in clean, dry area and cover with a

suitable protective cover that does not retain moisture.

WARNING! Storage covers could cause a fire

resulting in death or serious injury.

• Do not place a storage cover over a hot generator. Let

equipment cool for a sufficient time before placing the

cover on the equipment.

FCC/IC Compliance Statement

FCC Part 15 Information to User

Pursuant to part 15.21 of the FCC Rules, you are cautioned

that changes or modifications to transceiver not expressly

approved by Briggs & Stratton could void your authority to

operate the portable generator.

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1)

This device may not cause harmful interference, and

(2) this device must accept any interference received,

including interference that may cause undesired operation.

This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to part 15

of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause

harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be

determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV

technician for help.

IC Information to User

This device complies with Industry Canada’s licence-

exempt RSSs. Operation is subject to the following two

conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including

interference that may cause undesired operation of the

device.

Not for

Reproduction

Troubleshooting/Specifications

Problem Cause Correction

Engine is running, but no AC

output is available.

1. One of the circuit breakers is open.

2. Poor connection or defective cord set.

3. Connected device is bad.

1. Reset circuit breaker.

2. Check and repair.

3. Connect another device that is in good

condition.

Engine runs well at no-load

but “bogs down” when loads

are connected.

1. Generator is overloaded. 1. See Generator Capacity.

Engine will not start; starts

and runs rough or shuts

down when running.

1. Start switch in OFF position.

2. Fuel valve is in off (0) position.

3. Low oil level.

4. Dirty air cleaner.

5. Out of fuel.

6. Spark plug wire not connected to

spark plug.

7. Flooded with fuel.

8. Low battery charge.

1. Turn key in switch to RUN position.

2. Turn fuel valve to on (I) position.

3. Fill crankcase to proper level or place

generator on level surface.

4. Clean or replace air cleaner.

5. Fill fuel tank.

6. Connect wire to spark plug.

7. Wait 5 minutes and re-crank engine.

8. Charge battery for 24 hours.

Engine shuts down and CO

Guard LED blinks red (•• ••).

1. Generator improperly located.

1. Move generator to an open,

outdoor area. Air out premises (e.g.

open windows and doors) before

reoccupying. See CO Guard Carbon

Monoxide (CO) Shutdown System.

For all other issues, see a Briggs & Stratton authorized dealer.

Specifications

Running Watts* ...........................6,500

Starting Watts** ...........................8,200

AC Current at 240 Volts .................27 Amps

AC Current at 120 Volts ............... 54.1 Amps

Frequency. . . . . . . . . . . . . . . . . . . . . 60 Hz at 3600 rpm

Phase ............................ Single Phase

Displacement ................23.73 cu. in. (389 cc)

Spark Plug Gap ...............0.030 in. (0.76 mm)

Fuel Capacity .........7.0 U.S. Gallons (26.5 Liters)

Oil Capacity ................36 Ounces (1.0 Liters)

Power Ratings: The net torque rating for individual gasoline engine models is labeled in accordance with SAE (Society

of Automotive Engineers) code J1940 Small Engine Power & Torque Rating Procedure, and is rated in accordance with

SAE J1349. Net torque values are derived at 3600 RPM and are taken with exhaust and air cleaner installed. Given the

wide array of conditions in which they are placed, the gasoline engine may not develop the rated net torque when used in

a given piece of power equipment. This difference is due to a variety of factors including, but not limited to, the variety of

application limitations, ambient operating conditions (temperature, humidity, altitude), and engine-to-engine variability. Due

to manufacturing and capacity limitations, Briggs & Stratton may substitute an engine of higher rated torque for this engine.

*Generator certified in accordance with CSA (Canadian Standards Association) standard C22.2 No. 100-14, Motors and

Generators and PGMA (Portable Generator Manufacturers’ Association) standard ANSI/PGMA G300-2018, Safety and

Performance of Portable Generators.

** Per Briggs & Stratton 628K

Not for

Reproduction

18 www.oregonproducts.com

Troubleshooting

Schematic

MODULE

CHARGE

MODULE

Not for

Reproduction

Notes

Not for

Reproduction

20 www.oregonproducts.com

Warranty

80081354_EN Rev A

OREGON WARRANTY POLICY

LIMITED WARRANTY

Oregon® is a registered trademark of Blount, Inc. in the United States and other countries and is used under license to Briggs & Stratton Corporation. Briggs

& Stratton warrants that, during the warranty period specified below, it will repair or replace, free of charge, any part that is defective in material or workmanship

or both. Transportation charges on product submitted for repair or replacement under this warranty must be borne by purchaser. This warranty is effective for

and is subject to the time periods and conditions stated below. For warranty service, find the nearest Authorized Service Dealer in our dealer locator map at

BRIGGSANDSTRATTON.COM. The purchaser must contact the Authorized Service Dealer, and then make the product available to the Authorized Service Dealer

for inspection and testing.

There is no other express warranty. Implied warranties, including those of merchantability and fitness for a particular purpose, are limited to

the warranty period listed below, or to the extent permitted by law. Liability for incidental or consequential damages are excluded to the extent

exclusion is permitted by law. Some states or countries do not allow limitations on how long an implied warranty lasts, and some states or countries do not

allow the exclusion or limitation of incidental or consequential damages, so the above limitation and exclusion may not apply to you. This warranty gives you

specific legal rights and you may also have other rights which vary from state to state or country to country.**

WARRANTY PERIOD

* Applies to Briggs & Stratton engines only. Warranty coverage of non-Briggs & Stratton engines is provided by that engine manufacturer. Emissions-related

components are covered by the Emissions Warranty Statement.

** In Australia - Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a

major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods

fail to be of acceptable quality and the failure does not amount to a major failure. For warranty service, find the nearest Authorized Service Dealer in our dealer

locator map at BRIGGSandSTRATTON.COM, or by calling 1300 274 447, or by emailing or writing to [email protected], Briggs & Stratton

Australia Pty Ltd, 1 Moorebank Avenue, NSW, Australia, 2170.

The warranty period begins on the date of purchase by the first retail or commercial consumer. “Consumer use” means personal residential household use by a

retail consumer. “Commercial use” means all other uses, including use for commercial, income producing or rental purposes. Once a product has experienced

commercial use, it shall thereafter be considered as a commercial use product for purposes of this warranty.

Save your proof of purchase receipt. If you do not provide proof of the initial purchase date at the time warranty service is requested, the manufacturing date of the

product will be used to determine the warranty period. Product registration is not required to obtain warranty service on Briggs & Stratton products.

ABOUT YOUR WARRANTY

Warranty service is available only through Briggs & Stratton Authorized Service Dealers. This warranty covers only defects in materials or workmanship. It does not

cover damage caused by improper use or abuse, improper maintenance or repair, normal wear and tear, or stale or unapproved fuel.

Improper Use and Abuse - The proper, intended use of this product is described in the Operator’s Manual. Using the product in a way not described in the

Operator’s Manual or using the product after it has been damaged will not be covered under this warranty. Warranty coverage will also not be provided if the serial

number on the product has been removed or the product has been altered or modified in any way, or if the product has evidence of abuse such as impact damage

or water/chemical corrosion damage.

Improper Maintenance or Repair - This product must be maintained according to the procedures and schedules provided in the Operator’s Manual, and serviced

or repaired using genuine Briggs & Stratton parts or equivalent. Damage caused by lack of maintenance or use of non-original parts is not covered by warranty.

Normal Wear and Tear - Like most mechanical devices, your unit is subject to wear even when properly maintained. This warranty does not cover repairs when

normal use has exhausted the life of a part or the equipment. Maintenance and wear items such as filters, belts, cutting blades, and brake pads (except engine

brake pads) are not covered by warranty due to wear characteristics alone, unless the cause is due to defects in material or workmanship.

Stale or Unapproved Fuel - In order to function correctly, this product requires fresh fuel that conforms to the criteria specified in the Operator’s Manual. Engine or

equipment damage caused by stale fuel or the use of unapproved fuels (such as E15 or E85 ethanol blends) is not covered by warranty.

Other Exclusions - This warranty excludes damage due to accident, abuse, modifications, alterations, improper servicing, freezing or chemical deterioration.

Attachments or accessories that were not originally packaged with the product are also excluded. There is no warranty coverage on equipment used for

primary power in place of utility power or on equipment used in life support applications. This warranty does not include used, reconditioned, second-hand, or

demonstration equipment or engines. This warranty also excludes failures due to acts of God and other force majeure events beyond the manufacturer’s control.

Item Consumer Use Commercial Use

Equipment 24 months 12 months

Engine* 24 months 12 months

Battery (if equipped) 3 months None

La page charge ...