Whirlpool GU3200XTXB1 Guide d'installation

®

iNSTALLATiON iNSTRUCTiONS

UNDERCOUNTER DISHWASHER

iNSTRUCTiONS D'INSTALLATION

LAVE-VAISSELLESOUS PLAN DE TRAVAIL

Table of Contents ................................... 2

Table des matieres .................................. 24

W10282549A

Table of Confenfs

Dishwasher Safety ................................. 2

installation Requirements ........................... 3

Tools and Parts ................................... 3

Location Requirements ............................ 4

Drain Requirements ............................... 6

Water Supply Requirements ........................ 6

Electrical Requirements ............................ 6

installation instructions ............................. 7

Prepare Cabinet Opening--Existing Utilities ........... 7

Prepare Cabinet Opening--New Utilities .............. 7

Prepare and Route Water Line ...................... 8

install Drain Hose ............................... 10

install Moisture Barrier ........................... 11

Prepare Dishwasher ............................. 11

installation instructions (cent,}

Make Power Supply Cord Connection ............... 12

Determine Cabinet Opening ....................... 13

Choose Attachment Option ........................ 14

Move Dishwasher into Cabinet Opening ............. 15

Connect to Water Supply ......................... 17

Connect to Drain ................................ 17

Make Direct Wire Electrical Connection .............. 18

Secure Dishwasher in Cabinet Opening ............. 19

Complete installation ............................. 21

Check Operation ................................. 22

If Dishwasher Does Not Operate ................... 22

Additional Tips .................................. 22

DISHWASHER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Tip Over Hazard

Do not use dishwasher until completely installed.

Do not push down on open door.

Doing so can result in serious injury or cuts.

You Need to:

, Slowly open dishwasher door while someone grasps the

rear of the dishwasher. Remove shipping materials, drain

hose and lower rack. Close dishwasher door until latched.

, Observe all governing codes and ordinances.

, install this dishwasher as specified in these instructions.

, installation should be performed by a qualified service

technician. The dishwasher must be installed to meet all

electrical and plumbing national and local codes and

ordinances.

2

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the recommended tools and parts before starting

installation. Read and follow the instructions provided with

any tools listed here.

All Installations

Tools needed:

IF,at-b,ade

n,ers I screwdriver

5 1

_Ae and ¼ _..y'_ UL Listed or CSA

nut drivers or _ Approved twist-on ff

hex sockets _ wire connectors* v

10" adjustable wrench_ %" chert-end

that opens to _ wrench .-f-_-'_'-_'-

11/8"(2.9 cm) _.

If installing custom front panels, ..._y

Torx _t T15 screwdriver

-Must be the proper size to connect vour household wiring

to 16-gauge wiring in dishwasher

Other useful items you may need:

F ash ight _ Batht0we _

Parts supplied:

Drain hose

clamps (2)

(1 large and

1 small)

Drain hose #10 x W'

d Phillips-head

screws (2)

I

Silver Green, I

2- under-

counter

mounting

brackets (top)

Make sure all these parts are included in the literature package.

Parts needed:

3A,ICompr x ¾11Hose Fit

Eor part or kit, see local

retailer or call WhirlpoOl

Parts: !-800:442-9991 iPart

NumberW10273460

4 #10 x 1/2"wood screws (if installing custom front panels)

Other parts you may also need:

l 11/2'-2'' I Masking or IMoisture _i

(3.81-5:0 Cm) I du ct tape I barrier tape _1

Screw-type I I(Part Number T_J I

C ampsmaxim,m)/ 396277!:

NOTE: Moisture barrier tape is recommended when installing a

dishwasher under a wood countertop.

NOTE: Parts available for purchase in plumbing supply stores.

Check local codes. Check existing electrical supply. See

"Electrical Requirements" section. It is recommended that

electrical connections be made by a licensed electrical installer.

In addition, for first=time installations

Tools needed:

Cordless drill

• 1 " 3 "

with V2, Y4

and 11/2'' h

saw bits

Parts needed:

Co er tubin (%" 'see"Electrical Re uirements" section

PP g q

OD suggested) or

flex:blue braided For Direct Wire'.. For Power Supply

Water supp y ne use UL bsted/ ICord:Use UL L,sted

CSA Appr0ved power Supply C0rd

str ain relief I idt (Part Number

L_'..._......__j._..)_) tofit_ (2,2cm) 4317824)markedfor

h0!e uSe w!th dishWas her.

Additional parts supplied with top-venting models only:

Additional parts supplied with certain models only:

I B0tt0m Sound pad

I (located in lower rack) J

Make sure all these parts are included in the literature package.

If parts are not included, call 1-800-422-1230.

t® TORX is a registered trademark of Acument Intellectual Properties, LLC.

3

Location Requirements

Grounded electrical supply required.

Do not run drain lines, water lines or electrical wiring where

they can interfere with or contact dishwasher motor or legs.

The location where the dishwasher will be installed must

provide clearance between motor and flooring. Motor

should not touch the floor.

Do not install dishwasher over carpeted flooring.

Shelter dishwasher and water lines leading to dishwasher

against freezing. Damage from freezing is not covered by

the warranty.

A side panel kit is available from your dealer for installing

your dishwasher at the end of your cabinetry.

A moisture barrier accessory (Part Number 4396277) is

available from your dealer for installing underneath the

countertops. Call 1-800-422-1230 to order.

Check location where dishwasher will be installed. The

location must provide:

easy access to water, electricity and drain.

convenient access for loading and unloading dishes.

Corner locations require a 2" (5.1 cm) minimum

clearance between the side of the dishwasher door

and the wall or cabinet.

square opening for proper operation and appearance.

cabinet front perpendicular to floor.

level floor. (If floor at front of opening is not level with

floor at rear of opening, shims may be needed to level

dishwasher.)

Helpful Tip: Be sure to accurately measure dimensions

and ensure dishwasher is level if the floor in the

dishwasher opening is uneven (example: Flooring

extends only partway into opening).

NOTE: To avoid shifting during dishwasher operation,

shims must be securely attached to the floor.

If dishwasher will be left unused for a period of time or in a

location where it may be subject to freezing, have it

winterized by authorized service personnel.

Make sure pipes, wires and drain hose are within the

shaded area shown in the "Product and Cabinet

Opening Dimensions" section.

4

Product and Cabinet Opening Dimensions

*Insulation may

be compressed.

(not used on all models)

NOTE: Shaded areas of cabinet walls show where

utility connections may be installed.

*Measured from the lowest point on the

underside of countertop. May be reduced to

337/8"(86 cm) by removmg wheels from

dishwasher.

J

Check that all surfaces

have no protrusions that wpuld

_ohibit dishwasher installation.

_*Minimum, measured from narrowest point of s

opening.

Drain Requirements

, A new drain hose is supplied with your dishwasher.

If this is not long enough, use a new drain hose with a

maximum length of 12' (3.7 m) (Part Number 3385556)

that meets all current AHAM/IAPMO test standards, is

resistant to heat and detergent, and fits the 1" (2.5 cm)

drain connector of the dishwasher.

Make sure to connect drain hose to waste tee or disposer

inlet above drain trap in house plumbing and 20"

(50.8 cm) minimum above the floor. It is recommended

that the drain hose either be looped up and securely

fastened to the underside of the counter, or be connected

to an air gap.

Make sure to use an air gap if the drain hose is connected

to house plumbing lower than 20" (50.8 cm) above

subfloor or floor.

Use 1/2"minimum I.D. drain line fittings.

If required, the air gap, should be installed in accordance

with the air gap installation instructions. When you are

connecting the air gap a rubber hose (not provided) will

be needed to connect to the waste tee or disposer inlet.

Wafer Supply Requiremenfs

* A hot water line with 20-120 psi (138-862 kPa) water

pressure can be verified by a licensed plumber.

* 120°F (49°C) water at dishwasher.

* 3/8"O.D. copper tubing with compression fitting or

flexible braided water supply line (Part Number

4396897RP)

NOTE:1/2"minimum plastic tubing is not recommended.

* A 90° elbow with 3/4"Hose connection with rubber

washer

* Do not solder within 6" (15.2 cm) of the water inlet valve.

Eiecfrical Requiremenfs

Be sure that the electrical connection and wire size are

adequate and in conformance with the National Electrical

Code, ANSI/NFPA 70 - latest edition and all local codes and

ordinances.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park

Quincy, MA 02269

You must have:

120-volt, 60 Hz, AC-only, 15- or 20-amp, fused electrical

supply.

copper wire only.

We recommend:

a time-delay fuse or circuit breaker.

a separate circuit.

if connecting dishwasher

with a power supply cord:

, Use UL Listed power supply cord kit (Part Number

4317824) marked for use with dishwasher.

Power supply cord must plug into

a grounded 3 prong outlet, located in

the cabinet next to the dishwasher

opening. Outlet must meet all local

codes and ordinances.

if connecting dishwasher with direct wiring:

* Use flexible, armored

or nonmetallic

sheathed, copper wire

with grounding wire

that meets the wiring requirements for your home and

local codes and ordinances.

* Use a UL Listed!CSA Approved strain relief.

iNSTALLATiON iNSTRUCTiONS

Electrical Shock Hazard

Disconnect electrical power at the fuse box or circuit

breaker box before installing dishwasher.

Failure to do so can result in death or electrical shock.

D,_c0n_eCt electr'C a' power at the fuSe b0X oi Circu,t i

breaker b0x bef°re !nsta!!!ng dishwash

Yes _F011ow instructions in the "Prepa[e cabinet

Opening_Existing utilities,, section:

NO _FolloW instrUCti0nS inthe ,,Prepare Cabinet ....

Open!ng_New Ut!!it!es'! section:

E :isting g L ity hookups

Water line

Prepare Cabinet OpeningmExisfing

Utilities

If the water line and the cable extend to the locations

shown, proceed to the "Install Drain Hose" section. If they

do not reach far enough, follow the instructions in the

"Prepare Cabinet Opening--New Utilities" section.

Prepare Cabinet OpeningmNew

Utilities

Prepare and route the electrical supply

What type of electrical

connection will you use? L

Direct Wire:

F011ow opti0n B inst[uctionS

Option A, Power Supply Cord:

NOTE: A grounded 3 prong outlet is required inside a

cabinet next to the dishwasher cabinet opening.

Drill a 11/2'' (3.8 cm) hole in cabinet side or rear.

See product and cabinet opening dimensions.

7

Woodcabinet:Sandtheholeuntilsmooth.

Metalcabinet:Coverholewithgrommetincludedwith

powersupplycordkit.

OptionB, Direct Wire:

Helpful Tip: Wiring the dishwasher will be easier if you

route the cable into the cabinet opening from the right side.

Drill a ¾" (1.9 cm) hole in right-hand cabinet side or rear.

See product and cabinet opening dimensions.

Wood cabinet: Sand the hole until smooth.

Metal cabinet: Cover hole with grommet (Part Number

302797 - not provided).

8

Route cable from power supply through cabinet hole (cable

must extend to the right front side of cabinet opening).

Tape cable to the floor in area shown. This will keep cable

from moving when dishwasher is moved into cabinet

opening.

Prepare and Route Wafer Line

Helpful Tip: Routing the water line through the left side

of cabinet opening will make water connection easier.

Drill hole

Preferred locations

Drill a V2"(1.3 cm) hole in the cabinet side or rear.

Measure overall length of copper tubing or flexible

braided water supply line. Attach to the hot water line

using a connection configuration that is in compliance

with local codes and ordinances. The water line to the

dishwasher should have a manual shutoff valve.

Slowlyroutewatersupplylinethroughholeincabinet.

(Ifusingcoppertubing,itwillbendandkinkeasily,sobe

gentle.)Itshouldbefarenoughintothecabinetopening

toconnectittothedishwasherinletonthefrontleft

sideofthedishwasher.

Slowlyturnwatershutoffvalveto "ON"position.Flush

waterintoashallowpanuntilcleartogetridofparticles

thatcouldclogtheinletvalve.Turnshutoffvalveto

"OFF"position.

Coppertubingonly:Slidenut,thenferrule,about1"

(2.5cm)ontocoppertubing.

NOTE:Toavoidvibrationduringoperation,routethe

watersupplylinesothatitdoesnottouchthe

dishwasherbase,frameormotor.

Connectthe3/8"compressionfittingtothewatersupply

linepriortoinstallingtheunitintothecabinetopening.

Attachsuchthatthe3/4"connectionisfacingupward.

Coppertubingonly:Putthetubingintothe90°elbow

fittingasfarasitwillgo(thecoppertubingbendsand

kinkseasily).Slidethenutandferruleforwardandstart

thenutontotheelbowthreads.

Flexiblebraidedconnection:Securenuttoelbowusing

%"openendedwrenchoradjustablewrench.

NOTE:DonotuseTeflon®ttapewithcompression

fittings.

t® Teflon is a registered trademark of EJ. Du Pont de Nemours and Company.

9

InsfallDrain Hose

IMPORTANT: Always use a new drain hose. Check local

codes to determine if an air gap is required.

If needed, drill a 11/2"(3.8 cm) diameter hole in cabinet wall

or side of the opening closest to the sink.

Route drain hose as shown through hole in cabinet to the

front center of opening where drain connection will be

made. Tape drain hose to the floor in area shown. This will

prohibit it from moving when dishwasher is moved into

cabinet opening.

31Connect drain hose

Con nect d raJn hoSe tO waste tee or Waste disposer

using one of the following options:

option A, Waste disposer _ n0 air gap

, opti0n B,NO Waste dispOser _no air gap

option C, Waste disposer Jwith air gap

OPtion D, No waste disposer _with air gap

IMPORTANT: The drain hose connection of the disposer or

a waste tee must be made before the drain trap and at

least 20" (50.8 cm) above the floor where the dishwasher

will be installed.

Helpful Tip: To reduce vibration of the hose, keep the hose

away from the floor.

Option A, Waste disposer - no air gap

1. Using a hammer and screwdriver,

knock plug into disposer.

2. Use needle-nose pliers to remove

plug.

3. Attach drain hose to disposer inlet

with large silver drain hose clamp

(provided). Use pliers to squeeze

clamp open and move into position.

Option B, No waste disposer - no air gap

1. Connect black end of of drain hose to

waste tee and cut if needed.

(Do not cut ribbed section.)

2. Attach black end of drain hose to waste

tee with a large silver drain hose clamp

(provided). Use pliers to squeeze clamp

open and move into position. If the drain

hose was cut, use a 1W' to 2" (3.8 to

5 cm) screw-type clamp (not provided).

10

Option C, Waste disposer - with air gap

Drain trap

1. Using a hammer and screwdriver,

knock plug into disposer.

2. Use needle-nose pliers to remove

plug.

3. Connect black end of drain hose to air

gap and cut if needed. (Do not cut

ribbed section.)

4.

Attach drain hose to air gap with large

silver drain hose clamp (provided).

Use pliers to squeeze clamp open and

move into position. If the drain hose

was cut, use a 11/2'' to 2" (3.8 to

5 cm) screw-type clamp (not

provided).

5. Use a rubber hose (not provided) with

screw-type clamps (not provided) to

connect from air gap to disposer inlet.

Option D, No waste disposer - with air gap

2.

3.

Connect black end of drain hose to air

gap and cut if needed. (Do not cut

ribbed section.)

Attach drain hose to air gap with large

silver drain hose clamp (provided).

Use pliers to squeeze clamp open and

move into position. If the drain hose

was cut, use a 11A'' to 2" (3.8 to 5 cm)

screw-type clamp (not provided).

Use a rubber hose (not provided) with

screw-type clamps (not provided) to

connect from waste tee to air gap,

Install Moisfure Barrier

(under a wood counterfop)

Moisture

barrier

1. Make sure the area under the cabinet is clean and dry

for installation of the moisture barrier.

2. Remove the backing of the moisture barrier and apply

to underside of the countertop along the front edge of

the counter.

Prepare Dishwasher

Tip Over Hazard

Do not use dishwasher until completely installed.

Do not push down on open door.

Doing so can result in serious injury or cuts.

Excessive Weight Hazard

Use two or more people to move and install

dishwasher.

Failure to do so can result in back or other injury.

Put dishwasher on its __

11

Helpful Tip: Place cardboard under dishwasher until installed

in cabinet opening to avoid damaging floor covering. Do not

use door panel as a work table without first covering with a

towel to avoid scratching the door panel.

Using two or more people, grasp sides of dishwasher door

frame and place dishwasher on its back.

Using a 1/4"hex head socket, nut driver or Phillips

screwdriver, remove two screws attaching access panel

and lower panel to dishwasher. Do not remove tech

sheet from access panel.

Using a 1/4"hex head socket, nut driver or Phillips

screwdriver, remove terminal box cover. Retain for

later use.

Install a UL Listed/CSA Approved strain relief. Make sure

screwheads are facing to the left when tightening conduit

nut. Strain relief is provided with the power supply cord kit.

12

NOTE: If using Option B, proceed to "Determine Cabinet

Opening," to continue with the installation of your

dishwasher.

Make Power Supply Cord Connecfion

Option A, Power Supply Cord:

Route cord so that it does not touch dishwasher motor to

lower part of dishwasher tub. Pull cord through strain

relief in terminal bow. Take notice when installing or

removing the dishwasher in order to reduce the chance of

damaging the power supply cord.

Select UL Listed/CSA Approved twist-on wire connectors

(included with power supply cord kit) rated to connect your

power supply cord to 16-gauge dishwasher wiring.

ElectricalShock Hazard

Electrically ground dishwasher.

Connect ground wire to green ground connector

in terminal box.

Do not use an extension cord.

Failure to follow these instructions can result in

death, fire, or electrical shock.

--" Connect ground wire |

--_.

Remove the green grounding screw and place

through the ring terminal of the green ground wire.

Reattach and tighten the green screw.

NOTE: Twist on wire connector. Gently tug on wires to be

sure both are secured.

Connect wires black to black and white to white, using UL

Listed!CSA Approved twist-on wire connectors (included

with power supply cord kit).

Tighten strain relief screws to secure cord.

Place wires inside terminal box. Insert tabs

on left side of cover. Make sure wires are tucked inside

box. Close cover ensuring wires are not pinched. Use 1/4"

nut driver and previously removed screw to secure

cover.

NOTE: Do not plug into outlet until instructed to do so.

Determine Cabinet Opening

If needed, see website for animated representation of this 13

step. Visit www.whirlpool.com under FAQ tab.

Measureheightofcabinetopeningfromundersideof

countertoptofloorwheredishwasherwillbeinstalled

(youwillneedtomeasurethelowestpointonthe

undersideofthecountertopandthehighestpointonthe

floor).Referto"DishwasherHeightAdjustmentChart"

forwheelpositionandthenumberofturnsneeded.

Cabinet I :Wheel Number°fturns

opening height position on front leg

33%" (86,0 cm) I Removed A!I the way up

" I

34 (86.4cm) . 1 10

341 ,,(87:0era)2 s

,,_

NOTE: If the minimum cabinet opening height is less than

34" (86.4 cm), the rear wheels can be removed for

additional clearance. This will allow the dishwasher to fit

into a 337/8`' (86 cm) high cabinet opening, but the

dishwasher will be more difficult to move. (Measurements

are approximate. Wheels and legs are preset at the

factory for 341/2'' [87.6 cm].)

Adjust wheels and legs

)

Turn both leveler legs to the same height. Put wheels in

the required position determined from "Dishwasher

Height Adjustment Chart."

Built-up floors: If the kitchen floor is higher than the

cabinet opening's floor - for example, the kitchen floor tile

does not extend into the cabinet opening - add shims as

needed in the area shown to bring the dishwasher up to

34" (86.4 cm) below the countertop.

NOTE: Shims must be securely attached to floor to avoid

movement when the dishwasher is in use.

14

Choose Attachment Option

Excessive Weight Hazard

Use two or more people to move and install

dishwasher.

Failure to do so can result in back or other injury.

Using 2 or more people, stand the dishwasher up.

Option 1, Countertop attachment:

Remove the brackets from the package and place in the

open slots on the left and right-hand top of the

dishwasher collar as shown.

J

nsert the bracket into the slot on the collar. Using a pair

of pliers, bend the tab down to secure the bracket in

place. Repeat this step for the other side.

NOTE: Do not attach the dishwasher. This will be done

later.

Option 2, Dishwasher side attachment:

NOTE: Remove the brackets from the parts package.

_cole i ne/

Break off the end of the bracket along the scored line.

With another person holding the rear of the dishwasher

to keep it from tipping, open dishwasher door and place

towel over pump assembly and spray arm of dishwasher.

This will keep screws from falling into pump area when

you are securing dishwasher to cabinet.

plastic _i

Pushtheplasticbuttonsoutofthesideofthetub.

NOTE:Savethebuttonstocovertheholesafter

dishwasherisinstalled.

Pushbracketintoslotonthesideofdishwasher,and

bendtabintowardthesideofthedishwashersothatit

keepsthebracketinplace.Repeatthisstepfortheother

sideofthedishwasher.

NOTE:Donotattachthedishwasher.Thiswillbedone

later.

Move Dishwasher into Cabinet

Opening

Excessive Weight Hazard

Use two or more people to move and install

dishwasher.

Failure to do so can result in back or other injury.

11Stand dishwasher uprighl '

Using two or more people, stand dishwasher upright.

NOTE: Do not install kick plate until instructed to do so.

IMPORTANT: Double-check correct placement of utilities.

Grasp the sides of the dishwasher at the edges of the

door panel. Tilt dishwasher backward on wheels and

move dishwasher close to cabinet opening.

NOTE: Do not push on the front of the panel or on the

console. Panel or console may dent.

Helpful Tip: Temporarily tape utilities to the floor in the

locations shown to keep them from moving when

dishwasher is moved into the cabinet opening.

Check that water line is on the left side of opening and

drain hose is near the center of the cabinet opening.

With another person holding the dishwasher to keep it

from tipping, open and close the door a few times. If the

door closes or falls open under its own weight, the door

tension will need to be adjusted.

15

Toadjustthedoorspringtension,unhookthespring

fromtherearlegofdishwasher.

Usingas/16"nutdriverorhexsocket,removethescrew

fromthetensioner.

ThescrewcanbeputintooneofthreeholesIII1_1_t

in the front leg of dishwasher. If the door closes by itself,

move the tensioner to a lower-numbered hole and

replace screw. Reattach door spring to rear leg.

NOTE: Tensioners on both sides of dishwasher should be

secured at same holes.

When door is unlatched, if door opens by itself, move

the tensioner to a higher-numbered hole and replace the

screw. Reattach door spring to rear leg.

NOTE: Tensioners on both sides of dishwasher should

be secured at same holes.

blanket

IMPORTANT: If wheels were removed, cover the floor

when moving the dishwasher. Slowly move dishwasher

completely into cabinet opening. Do not kink or pinch

water line, drain hose, power supply cord or direct wire

between dishwasher and cabinet. Remove cardboard

from under dishwasher.

NOTE: It is all right if dishwasher fits tightly into cabinet

opening. Do not remove insulation blanket- the blanket

reduces the sound level.

NOTE: If using power cord, make sure to route end

through hole in cutout before sliding into cabinet opening.

Align front of dishwasher door panel with front of

cabinet doors. You may need to adjust alignment to be

even with your cabinets.

Check that leveling legs are firmly against the floor.

Close and latch the door, and place level against the

front panel. Check that dishwasher is centered from front

to back in the opening. If needed, adjust leveling leg until

dishwasher is plumb. Repeat for other side of dishwasher.

Helpful Tip: Push up on front of dishwasher to raise

dishwasher off the ground to adjust front legs. With

some installations, it may be easier to adjust the front leg

using the 3A6"hex head socket or adjustable wrench.

16

Placelevelagainsttopfrontopeningoftub.Checkthat

dishwasherislevelfromsidetoside.Ifdishwasherisnot

level,adjustfrontlegsupordownuntildishwasheris

level.

ii /i _iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii_i_i_iIiIiIiIi_

Connect to Water Supply

Be sure rubber washer is properly seated in fitting. Slide

the 3/4"fitting up to the valve and hand tighten to avoid

cross-threading. Hand tighten until the coupling is tight.

Using pliers, check the tightness of the coupling. An

additional 1/4to 1/2turn may be required to seal the rubber

gasket.

NOTE: Do not overtighten. Damage to the coupling can

result.

Place paper towel under 90° elbow fitting. Turn on water

supply and check for leaks. If leak occurs, repeat

previous step.

If needed, see website for animated representation

of this step. Visit www.whirlpool.eom/watersupply

under FAQ tab.

iiiiii_iii iiii_i/i i/i_iiii

Connect to Drain

drain

loop

To help minimize vibration, route drain hose to avoid

contact with motor, door springs, water line, cabinet,

flooring or the edge of the hole where it passes through

the cabinet.

Do not remove drain loop from side of dishwasher.

Place pan under end of drain hose. Pan will collect any

water in drain hose.

Place towel under drain hose to catch any water in drain

hose. Place the small green drain hose clamp onto the

small end of the drain hose. Push the new drain hose

into the black drain hose connector up to the drain hose

stop.

Using pliers, squeeze open the small green drain hose

clamp and slide onto connector between stops.

17

Afterhoseisconnected,removetowel.

Ifneeded,seewebsiteforanimatedrepresentationof

thisstep.Visitwww.whirlpool.eom/drainunderFAQtab.

Make DirectWire Electrical

Connection

NOTE: If the power supply cord was connected earlier,

proceed to "Secure Dishwasher in Cabinet Opening"

section.

Option B, Direct Wire:

Route cable so that it does not touch dishwasher motor

or lower part of dishwasher tub. Pull cable through UL

Listed or CSA Approved strain relief in terminal box.

Strain relief is not supplied with the dishwasher. Owner

must purchase a 7/8"screw-in type strain relief.

Select UL Listed or CSA Approved twist-on wire connectors

(not included) rated to connect your household wiring to

16-gauge dishwasher wiring.

Electrical Shock Hazard

Electrically ground dishwasher.

Connect ground wire to green ground connector

in terminal box.

Do not use an extension cord.

Failure to follow these instructions can result in

death, fire, or electrical shock.

2_jD¸I¸¸¸¸¸¸¸¸'rec(w¸i;e ¸¸¸c0¸¸¸nn¸¸¸¸¸¸e ¸¸ct¸¸'¸¸ ilili

ground wire

_._-_--0

<1

wlrl_lre I _ _'_."e _ _!

ash1

Ground/

Form bare ground wire into a U-shaped hook. Wrap

ground wire hook clockwise around ground connector

screw and under the washer. Securely tighten ground

connector.

NOTE: Twist on UL Listed or CSA Approved wire

connector. Gently tug on wires to be sure both are

secured.

Connect wires black to black and white to white, using

UL Listed or CSA Approved twist-on wire connectors

(not included).

18

Wi ring co nf ig uratio n*_::

Power Supply wire: Terminal box wire:

If needed, see website for animated representation

of this step. Visit www.whMpool.eom/eleetrieal under

FAQ tab.

Tighten strain relief screws to secure cable.

Place wires inside terminal box. Insert tabs on left side

of cover. Make sure wires are tucked inside box. Close

cover ensuring wires are not pinched. Use 1/4"nut driver

and previously removed screw to secure cover.

Secure Dishwasher inCabinet

Opening

Check that dishwasher is still level front-to-back and

side-to-side in cabinet opening,

Open dishwasher door, remove lower dish rack, and

place towel over pump assembly and lower spray arm of

dishwasher. This will prohibit screws from falling into

pump area when securing dishwasher to countertop.

NOTE: Do not drop screws into bottom of dishwasher.

Locate brackets on top of dishwasher and secure

dishwasher to countertop with two, #10 x 1/2"Phillips-head

screws (included). The dishwasher must be secured to

keep it from shifting when door is opened.

19

Checkthattopofdoordoesnotcontactscrews,

brackets,orcountertop.Ifitdoes,adjustlevelinglegs.

Opendoorandcheckthatspacebetweendishwasher

cabinetopeningandtubisequalonbothsides.If

spacingisnotequal,loosenbracketscrewssecured

andshifttub.Tightenbracketscrews.

Ifsecuringwithasideattachment,checkthatsidesofdoor

donotrubagainstthescrewheads.Iftheydo,dishwasher

mustbere-centered.Whendishwasherisproperlycentered,

replaceplasticbuttons.

Removetowelfromdishwasher.Reinstallthelowerdish

rack.

Ifneeded,seewebsiteforanimatedrepresentation

ofthisstep.Visitwww.whirlpool.corn/anchoringunder

FAQtab.

20

La page charge ...

Whirlpool GU3200XTXB1 Guide d'installation

Ce manuel convient également à

Whirlpool GU3200XTXB1 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents