Lifesmart FP1136 Mode d'emploi

Marque: Lifesmart

Modèle: FP1136

Catégorie: Cheminées

Taper: Mode d'emploi

Questions, problems, missing parts? Contact technical support department at

657-341-0362, 9:00 a.m. - 5 p.m., CST, Monday - Friday or visit us online at

www.lifesmartcomfort.com

Please have your model and serial number ready

ATTACH YOUR RECEIPT HERE

Purchase Date ____________Serial Number (located on back of unit) __________________

lifesmart

is a registered trademark of

REV1-100918

INFRARED QUARTZ

FIREPLACE

Customer number:

FP2042, MDFP2042US, MDFP2090US

TABLE OF CONTENTS

Package Contents ............................................................... 3

Safety Information .............................................................. 4

Frequently Asked Questions ...................................................... 6

Preparation .................................................................... 8

Troubleshooting ................................................................ 8

Control Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Remote Control ................................................................ 10

Operating Instructions .......................................................... 11

Care and Maintenance .......................................................... 13

One-Year Limited Warranty ...................................................... 14

Replacement Parts List ......................................................... 15

PACKAGE CONTENTS

PART DESCRIPTION QUANTITY

A Infrared Heater 1

B Remote Control 1

C Control Panel (preassembled to Infrared Heater (A)) 1

D Temperature Sensor (preassembled to Infrared Heater (A)) 1

E 3-prong Power Cord (preassembled to Infrared Heater (A)) 1

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate, or install the product.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: POTENTIAL ELECTRICAL HAZARD IF NOT ADHERED TO. When using electrical

appliances, basic precautions should always be followed to reduce the risk of ﬁre, electric shock, and

injury to persons, including the following:

• This heater must be plugged into a 120 V, 15 amp (or more) circuit of its own. Do not plug anything

else into the same circuit. If unsure if your home meets this speciﬁcation, consult a certiﬁed

electrician prior to use. Risk of ﬁre, overheating, malfunction, property damage, injury, or even

death may result if not adhered to!

• Connect to a properly grounded, 3-prong outlet only. Do not connect the heater to extension cords,

surge protectors, timers, direct breakers, or an outlet with other appliances connected to the same

outlet. Risk of ﬁre, overheating, malfunction, property damage, injury, or even death may result

if not adhered to!

• This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Use handles

(certain models) or wheels to move this heater.

• Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at

least 3 ft. (0.9 m) from the front of the heater and keep them away from the sides and rear of the

heater.

• Extreme caution is necessary when any heater is used by or near children, invalids, pets, or when

the heater is left operating unattended.

• Always unplug the heater when not in use.

• Do not operate any heater with a damaged cord or plug or after the heater malfunctions, has been

dropped, or damaged in any manner. Contact the manufacturer for resolution options.

• Do not use outdoors. Exposure to outdoor elements such as rain, snow, sun, wind, or extreme

temperatures may cause the heater to become a safety hazard.

• This heater is not intended for use in bathrooms, laundry areas, and similar indoor locations, nor

any locations that use GFCI outlets.

• Never place the heater where it may fall into a bathtub or other water receptacles.

• Do not run the cord under carpet. Do not cover the cord with throw rugs, runners, or similar

coverings. Arrange the cord away from trafﬁc areas and where it will not be tripped over.

• The heater must be plugged into a wall outlet that is a dedicated circuit with a minimum 15 amp

rating on that individual circuit.

• To disconnect the heater, ﬁrst turn the power button to the OFF position and then remove the plug

from the wall outlet.

• Do not allow foreign objects to enter or block any ventilation or exhaust opening as this may cause

electric shock, ﬁre, or damage the heater.

• Allow at least 3 ft. of unobstructed space to the front and rear of the heater to allow for maximum

heat, air, and ventilation ﬂow.

• A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint,

or ﬂammable liquids are used or stored, nor use ﬂammable solvents to clean the heater. Keep the

heater dry at all times.

• Use this heater only as described in this manual. Any other use not recommended by the

manufacturer may cause ﬁre, electric shock, or injury to persons.

• Do not use abrasive solvents to clean the heater as it may cause damage to the ﬁnish or casing.

• To prevent a possible ﬁre, do not block air intakes or exhaust in any manner. Do not use on soft

surfaces, like a bed, where opening may become blocked.

• Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or

relocatable power tap (outlet/power strip).

SAVE THESE INSTRUCTIONS

SAFETY INFORMATION

Child Lock Safety Feature

Press and hold the child lock button located on the control panel for 5 seconds or

remote control for 3 seconds. Locking is conﬁrmed when a buzzer rings and the

control panel displays “CL”. When locked, the control panel and remote control (if

provided) will not function.

To unlock the control panel or remote (if provided), repeat this procedure.

Unlocking is conﬁrmed when a buzzer rings and the lock indication disappears.

Tip-Over Safety Feature

This heater is equipped with a tip-over safety feature. Once the heater is tipped over, an internal switch

will automatically shut the heater off. Once the heater is restored to an upright position, the heater will

reset. To continue operation, turn on the heater using the control panel or supplied remote control (if

provided) on the heater.

Overheat Safety Feature

This heater is equipped with an overheat safety feature. When the internal components of the heater

reach a certain temperature that could cause overheating or possible ﬁre, the heater will automatically

shut off. If the unit has been overheated, you will need to unplug the unit from the wall and replug it in

to use the heater again.

WARNING: This heater has a voltage rating of

120 volts. The cord has a three-blade, grounding-

type plug. An adapter is available for connecting

three-blade grounding-type plugs to two-slot

receptacles. The grounding lug extending from

the adapter must be connected to a permanent

ground such as a properly grounded outlet box.

The adapter should not be used if a three-slot

grounded receptacle is available.

DO NOT DEFEAT THE SAFETY PURPOSE OF THE

GROUNDED PLUG.

Grounding Pin

Grounding Means

Grounding Pin

Metal Screw

Cover of Grounded

Outlet Box

WARNING: It is normal for the power cord to feel warm to the touch. However, a loose ﬁt between

the outlet and the plug may cause overheating of the plug. If this occurs, try inserting the plug into a

different outlet. Contact a qualiﬁed electrician to inspect the original outlet for damage.

Speciﬁcations

Voltage Rating 120 V (60 Hz)

Power Consumption

1,000 W/1,500 W

Unit Size 28.5 in. (W) x 11.0 in. (D) x 21.7 in. (H)

Unit Weight 46.8 lbs.

INFORMATIONS SUR LA SÉCURITÉ

Veuillez lire et comprendre ce manuel entier avant d’essayer d’assembler, d’utiliser ou d’installer l’appareil.

CONSIGNES DE SÉCURITÉ IMPORTANTES

AVERTISSEMENT: RISQUE POTENTIEL D’ÉLECTROCUTION SI LES CONSIGNES DE SÉCURITÉ NE SONT

PAS RESPECTÉES. Lors de l’utilisation d’appareils électriques, les précautions de base doivent toujours être

suivies pour réduire le risque d’électrocution, d’incendie et de blessure corporelle, notamment :

• Ce radiateur doit être branché sur un circuit 120 V, 15 A (ou plus) qui lui est propre. Ne branchez rien d’autre

sur le même circuit. Si vous n’êtes pas sûr(e) que votre habitation réponde à cette spéciﬁcation, consultez

un électricien certiﬁé avant toute utilisation. Si cette spéciﬁcation n’est pas remplie, il y a risque d’incendie,

de surchauffe, de mauvais fonctionnement, de dommages matériels, de blessures, voire même la mort.

• Branchez l’appareil uniquement dans une prise à 3 trous correctement mise à la terre. Ne branchez

pas le radiateur dans des rallonges électriques, des limiteurs de surtension, des minuteries, des

coupe-circuits directs ou dans une prise où d’autres appareils sont également branchés. Si cette

spéciﬁcation n’est pas remplie, il y a risque d’incendie, de surchauffe, de mauvais fonctionnement,

de dommages matériels, de blessures, voire même la mort.

• Ce radiateur est chaud quand il est utilisé. Pour éviter les brûlures, ne laissez pas la peau nue toucher des

surfaces chaudes. Utilisez les poignées (sur certains modèles) ou les roues pour déplacer ce radiateur.

• Maintenez les matériaux combustibles, par exemple les meubles, les oreillers, la literie, les papiers,

les vêtements et les rideaux au moins éloignés de 0,9 m (3 pi) de la façade du radiateur et maintenez-

les à l’écart des ﬂancs et de l’arrière du radiateur.

• Il faut prendre des précautions extrêmes quand un radiateur est utilisé à côté ou près d’enfants, de

personnes handicapées, d’animaux familiers ou quand le radiateur est utilisé sans surveillance.

• Débranchez toujours le radiateur quand il n’est pas utilisé.

• N’utilisez pas un radiateur ayant un cordon ou une prise endommagés ou s’il fonctionne mal, s’il est

tombé ou s’il a été endommagé d’une manière ou d’une autre. Communiquez avec le fabricant pour

savoir comment remédier à ces problèmes.

• Ne pas utiliser en plein air. L’exposition du radiateur aux éléments naturels, par exemple la pluie, la

neige, le soleil, le vent ou les températures extrêmes, peut rendre son utilisation dangereuse.

• Ce radiateur n’est pas destiné à être utilisé dans les salles de bain, les buanderies et autres lieux

intérieurs similaires, ni dans les endroits ou des prises à disjoncteur de fuite de terre sont utilisées.

• Ne placez jamais le radiateur dans un endroit d’où il pourrait tomber dans une baignoire ou dans

d’autres réceptacles contenant de l’eau.

• Ne faites pas courir le cordon sous un tapis. Ne recouvrez pas le cordon d’une carpette, d’un tapis

d’escalier ou d’éléments couvrants similaires. Disposez le cordon à l’écart des zones de circulation et

des endroits où l’on pourrait trébucher dessus.

• Le radiateur doit être branché dans une prise murale ayant son propre circuit d’une intensité nominale

minimale de 15 A.

• Pour débrancher le radiateur, tournez d’abord le bouton de mise sous tension sur la position « OFF »

(ARRÊT) et retirez ensuite la ﬁche de la prise murale.

• Ne laissez pas d’objets étrangers pénétrer ou bloquer les ouvertures de ventilation ou d’échappement,

car ceci peut être à l’origine de décharges électriques, d’incendie ou risque d’endommager le radiateur.

• Laissez un dégagement libre de toute obstruction d’au moins 0,9 m (3 pi) devant et à l’arrière du

radiateur pour permettre à la chaleur, à l’air et à la ventilation de circuler librement.

• L’intérieur du radiateur contient des pièces chaudes pouvant produire des décharges électrostatiques

ou des étincelles. Ne l’utilisez pas dans des endroits où de l’essence, de la peinture ou des liquides

inﬂammables sont utilisés ou stockés, et n’utilisez pas de solvants inﬂammables pour nettoyer le

radiateur. Maintenez en permanence le radiateur sec.

• Utilisez ce radiateur uniquement comme cela est décrit dans ce manuel. Toute autre utilisation non

recommandée par le fabricant peut causer un incendie, des décharges électriques ou blesser des personnes.

• N’utilisez pas de solvants abrasifs pour nettoyer le radiateur, car ils pourraient endommager le

revêtement ou l’enveloppe.

• Pour éviter un incendie, ne pas bloquer les entrées et sorties d’air de quelque manière. Ne pas utiliser

sur des surfaces molles, comme un lit, où l’ouverture peut être bloqué.

• Toujours brancher chauffe directement dans une prise murale / réceptacle. Ne jamais utiliser une

rallonge ou robinet d’alimentation relocalisable (sortie de bande / de puissance).

CONSERVER CES INSTRUCTIONS

INFORMATION DE SÉCURITÉ

Dispositif de sécurité et de verrouillage pour enfant

Appuyez pendant 5 secondes sur le bouton de verrouillage pour enfant situé

sur le tableau de commande. Le verrouillage est conﬁrmé quand un vibreur se

déclenche et que le tableau de commande afﬁche « CL ». Quand le radiateur est

verrouillé, le tableau de commande et la télécommande ne fonctionnent pas

Pour déverrouiller le tableau de commande et la télécommande, répétez cette

procédure. Le déverrouillage est conﬁrmé quand un vibreur se déclenche et que

« CL » cesse de s’afﬁcher.

Dispositif de sécurité après-basculement

Ce radiateur est équipé d’un dispositif de sécurité après-basculement. Une fois que le radiateur a

basculé, un commutateur interne l’arrête automatiquement. Une fois que le radiateur retrouve sa

position debout, il peut être remis en marche. Pour poursuivre l’opération, allumez le radiateur en

utilisant la télécommande fournie ou le tableau de commande sur le radiateur.

Dispositif de sécurité anti-surchauffe

Ce radiateur est équipé d’un dispositif de sécurité anti-surchauffe. Quand les composants internes

du radiateur atteignent une certaine température pouvant causer une surchauffe ou potentiellement

un incendie, le radiateur s’éteint automatiquement. Si l’appareil a surchauffé, vous aurez besoin de

débrancher l’appareil du mur et le rebrancher pour utiliser le chauffe à nouveau.

AVERTISSEMENT: Ce radiateur à une tension

nominale de 120 V. Le cordon est équipé d’une ﬁche

à trois lames reliée à la terre. Un adaptateur est

disponible pour brancher les ﬁches à trois lames

reliées à la terre aux prises à deux trous. La patte

de mise à la terre ressortant de l’adaptateur doit

être connectée de façon permanente à la terre, par

exemple à une boîte à prises correctement mise à

la terre. L’adaptateur ne doit pas être utilisé si une

prise à trois trous mise à la terre est disponible.

NE PAS CONTOURNER L’OBJECTIF DE SÉCURITÉ

DE LA FICHE MISE À LA TERRE.

Moyens de mise

à la terre

Lame de mise

à la terre

Lame de mise

à la terre

Couvercle à vis métal

de mise à la terre

Boîte à prises

AVERTISSEMENT: Il est normal que le cordon d’alimentation soit chaud au toucher. Toutefois, une

ﬁche mal enfoncée dans la prise peut entraîner la surchauffe de la ﬁche. Si cela se produit, essayer

d’insérer la ﬁche dans une prise différente. Communiquer avec un électricien qualiﬁé pour qu’il vériﬁe

si la prise d’origine est endommagée.

Spéciﬁcations

Voltage 120 V (60 Hz)

Consommation d’énergie

1,000 W/1,500 W

Taille d’unité 28.5 in. (W) x 11.0 in. (D) x 21.7 in. (H)

Unité de poids 46.8 lbs.

FREQUENTLY ASKED QUESTIONS

Please review these frequently asked questions on the next few pages prior to using your heater.

Q. My heater emits a strange odor when I ﬁrst open the box and when I turn the heater on for the ﬁrst

time. Why is this happening?

A. This is normal. This heater is treated with a special heat safe/resistant coating. This odor will

sometimes be present when the box is opened. When the coating is exposed to heat, it produces this

particular odor during the ﬁrst few hours of operation. This will dissipate after the break-in period. If

you are sensitive to odors, you may want to pre-burn the unit in a garage with the door open until the

initial odor dissipates.

Q. If my heater runs on its max wattage setting, how many BTUs is that?

A. This heater is intended to be used as supplemental heat in areas most needed. It may take several

minutes to several hours to heat your area, depending on various factors. The below chart provides BTU

translations for different wattages.

WATTAGE BTUS

1,500 5,118

1,000 3,412

750 2,559

500 1,706

Q. Can the heating elements be replaced?

A. Replacement heating elements can be obtained from the manufacturer. All parts may be purchased

through the manufacturer if your product is out of warranty. If you feel that the elements are deﬁnitely

faulty right out of the box, contact Customer Support. A representative can then direct you to the next

step.

Q. Once I plug the unit in and turn it on, how long will it take to heat my room?

A. The heating process in the heater begins immediately upon powering on and setting the desired

temperature above the ambient temperature. A noticeable change in the ambient temperature of the

room will vary due to variables such as the location of the heater (in the home), ﬂoor plan and size of

the room, how well the room is insulated, how many doors/windows, how much bare concrete (acts as

a heat sink with any type of heating), the opening and closing of an exterior door, long hallways, high

ceilings, etc. Customers with smaller rooms experience quick heat changes. Rooms with larger and

open ﬂoor plans can expect up to 24 hours to completely heat up.

Q. I do not have a grounded outlet. Can I use adapters, a 2-prong power strip, or remove the ground

prong from the cord?

A. NO! If you do not have a grounded outlet, contact a certiﬁed electrician for advice. Removing or

altering any part of the heater’s original design or intent (including the power cord) will void the

warranty and make you liable for any unexpected or hazardous results.

Q. My Heater has an ECO setting? How does this setting work?

A. The ECO mode on your heater is a program that attempts to keep the temperature strictly at a

“warm” 68° F (20°C). This also helps with efﬁciency, as it is programmed to 1) Increase the power

to the unit’s maximum wattage if the temperature drops below 64.4°F (18°C) 2) Gradually reduce the

wattage used as it approaches 66.2° (19°C) F and 3) Stop heating when 68° F (20°C) is achieved. This

is considered an Economical function, since in the ECO setting, the heater is almost never running at

the maximum watts.

FREQUENTLY ASKED QUESTIONS

Q. The temperature on my heater does not match the temperature display on my wall, or external

thermostat. Why?

A. This is completely normal. The temperature display on your heater may vary from the temperature

display on another thermostat (like the one mounted to your wall or a purchased external thermostat).

This is because the temperature sensor on the heater reads the temperature directly around the heater.

With the heater near the cold ﬂoor (and heat rising), any readings on elevated or external thermostats

will differ in readings on the heater. The best way to operate your heater is to set the unit on High and

dial up to a temperature that feels comfortable to you. Then, leave it at that temperature, regardless of

the mismatch. The heater will cycle off when the set temperature is met or exceeded slightly.

Q. Can I use more than one heater at a time? Can I use the heater and another appliance at the same

time?

A. Yes, but make sure they are not plugged into the same circuit. Each heater requires its own minimum

15-amp circuit with no other items plugged into that circuit or outlet. This is because heaters are

considered appliances and draw out high amperage. If you are unsure your circuit meets these

requirements, verify with a certiﬁed electrician.

WARNING: Risk of ﬁre, damage to property, or injury may result if requirements are not met.

Q. Why does my heater’s fan continue to run after the set temperature is reached or the power is turned

off?

A. This is normal. The heater’s fan will continue to run even after the heater automatically cycles down.

The fan continues to run so that every last bit of heat is blown out of the heat chamber while allowing

the unit to continue ﬁltering your air. Once the internal box/components cool completely, the fan should

then shut off on its own. In this case, allow a few minutes after the heat cycles off (with power on). The

fan will shut off faster when the power is turned off.

Q. My heater’s display shows my ambient temperature to be in the 20s when I know it is warmer than

that. Why?

A. The heater’s display is defaulted to read the temperature as Fahrenheit. If your heater is deﬁnitely

heating but shows it is in the 20s you probably have the setting to read your temperature in Celsius

rather than Fahrenheit.

Q. My heater’s power cord gets warm. My cord is showing signs of heat or melting at the outlet. Is

this normal?

A. A warm power cord is normal. These power cords are rated safe for up to 105°C/ 221°F by the UL,

CSA, or ETL. The exception is, if you detect heat, smoke, or signs of melting at the contact point of

the wall outlet, it may be due to loose or worn wall contacts (or arcing). Please stop using the heater

immediately, contact warranty support for a replacement power cord, and have a certiﬁed electrician

replace the wall outlet as soon as possible.

PREPARATION

Place the heater on a ﬁrm, level surface and plug into a grounded 120 V, 60 Hz power outlet and turn on

the power switch on the rear of the unit. Only operate heater in upright position.

Insert two AAA batteries into the remote control before using (batteries not included). *(Not all products

will include a remote control.)

Please note that infrared heaters do not heat like a traditional space heater. You should not expect

infrared heaters to blow hot air like a traditional space heater. Infrared heaters heat objects not air.

Infrared heaters are intended to supplement an already heated, insulated room. Square footage

speciﬁcations assume a single enclosed room not an entire home. Infrared heaters do not heat through

walls, ﬂoors, and are not intended to replace a main heat source. Infrared heat can take at least 24

hours to warm a room but operate much more efﬁciently to maintain the desired temperature. Infrared

heaters will not work well in uninsulated unheated spaces like screened in porches, RV’s, garages,

unheated basements, etc.

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION

The heater

does not turn

on.

1. The power cord is not plugged in.

2. The electricity at the main fuse

box is not working.

3. The battery in the remote control

is dead.

4. The thermostat on the heater

is set lower than the room

temperature.

1. Plug the power cord into an electrical

outlet.

2. Check the electricity at the main fuse

box.

3. Replace the batteries in the remote

control.

4. Increase the thermostat temperature

on the heater for a higher heat setting.

The heater

displays an

error code

“E1”

1. The heater has overheated.

2. Insufﬁcient power to the unit

3. Insufﬁcient air ﬂow to the heater.

1. Unplug the heater from the wall, wait a

few seconds then plug the power cord

back in.

2. Make sure the unit is plugged into

a dedicated 3-prong outlet, with no

extension cords or surge protectors.

3. Move the unit at least 3ft from the wall.

The heater

displays an

error code

“E2”

1. Temperature sensor not

functioning properly.

1. Please contact technical support.

CONTROL PANEL

1 2 3 4

567891011

PART NAME DESCRIPTION

1 Digital Display Readout of the set room temperature or timer value

2 Celsius Indicator Light Indicates that the temperature is being displayed in Celsius

3 Fahrenheit Indicator Light Indicates that the temperature is being displayed in Fahrenheit

4 Power Indicator Light Indicates when the unit is receiving power from the wall outlet

5 Power Switch Button Powers the heater ON or OFF

6 Flame Effect Button Toggles the Flame Effect from High/Med/Low/Off

7 Temp-Down Button Decreases the set temperature

8 Temp-Up Button Increases the set temperature

9 Timer Button Engages the on/off timer function

10 Heater Mode Button Toggles between Hi / Low / Eco Modes

11 Safety Lock Button Hold to Lock / Unlock heater’s control panel

12 Low Heat Indicator Indicates when Low Heat mode is on

13 High Heat Indicator Indicates when High Heat mode is on

14 Energy Saving Indicator Indicates when energy-saving mode is on

REMOTE CONTROL

PART NAME DESCRIPTION

1 Temp Up Button Increases the set temperature value

2 Mode Button Toggles between the three heat modes available

3 Temp Down Button Decreases the set temperature value

4 Power Button Powers the heater on or off

5 Flame/Lock Button

Short press: Toggles the Flame Effect from High/Med/Low/Off. /

Long press: for 3 seconds to activate lock function.

6 Timer Button Engages the timer on or off

OPERATING INSTRUCTIONS

1. Turn the heater on or off by pressing the

Power button on the control panel (C) or by

pressing the ON/OFF button on the remote

control (B).

Once the power is off, heating elements

will stop working ﬁrst. The fan will continue

working for up to 90 seconds to dispense

residual heat inside the heater. This is a

normal function.

C B

2. Select a heat setting by pressing the MODE

button on either the control panel (C) or the

remote control (B) to toggle between the

three heat settings.

Power for high is 1,500 W; low is 1,000 W. ECO

mode is an economic energy saving function.

When ECO mode is chosen, the heater will

operate to maintain a constant warm 68°F.

Note: The ECO LED light will only illuminate

when the ECO function is active and the

ambient room temperature falls below

68ºF / 20ºC.

C B

HIGH LOWECO

3. Set the temperature by pressing the arrows on

the control panel (C) or the remote control (B).

You can set the temperature on the heater

anywhere between 50°F and 90°F or between

10°C and 32°C. Once you have chosen the

desired temperature, the heater will remain

on until the room temperature increases to

the temperature on the digital display. The

heater will cycle on and off to maintain the

desired room temperature.

To engage the child lock press the child lock

button on the control panel (C).

Note: To engage the child lock press the child

lock button on the control panel (C) or

the remote (B), long press the child lock

button for 3 seconds to engage the child

lock.

OPERATING INSTRUCTIONS

4. To set the timer to power off the heater, start

the unit and press the Timer button on the

control panel (C) or remote control (B).

Note: The timer-power-off function can only

be set when the heater is in power-on

mode.

The digital display on the control panel (C)

changes from the set temperature readout

to a time value for the timer. Press the Timer

button repeatedly to change the number

value between a range of 0 to 12 hours (in

1-hour intervals).

5. To set the timer to power on the heater, ﬁrst

ensure the unit is powered off, then press the

timer button on the control panel (C).

Note: The timer-power-on function can only

be set when the heater is in power-off

mode.

The digital display on the control panel (C)

will indicate time value for the timer. Press

the Timer button repeatedly to change the

number value between a range of 0 to 12

hours (in 1-hour intervals).

6. To power on or adjust the ﬂame effect bright-

ness, press the Flame Effect button on the

control panel (C) or short press the Flame

Effect Button on the remote control (B)

Note: The ﬂame effect function can be set

when the heater is on or off.

The unit will cycle between, high, medium,

low and off brightness levels

C B

7. To replace the batteries, remove the battery

cover (1) from the remote (B) by applying

pressure to the battery cover (1) and sliding

it away from the remote (B). Insert two AAA

batteries (not included) (2) and close the re-

mote by placing the battery cover (1) back on

the remote (B).’

Note: Do not mix old and new batteries. Do not

mix alkaline, standard (carbon-zinc), or

rechargeable (NiCad, Ni-Mh, etc) bat-

teries.

1 2

CARE AND MAINTENANCE

WARNING: Before performing any maintenance task, unplug the unit, and allow it to cool completely.

1. To keep the heater clean, clean the outer shell with a soft, damp cloth. Use a mild detergent if

necessary. After cleaning, dry the unit with a soft cloth.

CAUTION: DO NOT let liquid enter the heater.

2. DO NOT use alcohol, gasoline, abrasive powders, furniture polish, or rough brushes to clean the

heater. This may cause damage or deterioration to the surface of the heater.

3. DO NOT immerse the heater in water.

4. Wait until the unit is completely dry before use.

5. If you will not be using the heater for a while, take the batteries out of the remote control and

store for future use.

6. Store the heater in a cool, dry location when not in use. To prevent dust and dirt build-up, use

the original packaging to repack the unit.

REPLACING THE FLAME EFFECT BULB - Bulb Requirements: E12 (small) Socket Base (2) Max 40 watts.

1. To replace the ﬂame effect bulbs (2), ensure the heater is unplugged ﬁrst. Remove the access

panel (1) by removing the six screws holding the panel in place. Remove and replace the two

light bulbs (2) by unscrewing each bulb slowly from the socket base.

2. Reassemble and reinstall the access panel (1).

WARNING: Do not replace heater light bulbs immediately after use or during heater operation.

1 1

ONE-YEAR LIMITED WARRANTY

The manufacturer warrants this heater against defects in materials and workmanship on functional

parts, for a period of 1 year from the original date of purchase. Your sales receipt showing the date

of purchase of the product is your proof of purchase. Keep it in a safe place for future reference. This

warranty is subject to personal use only, commercial or rental applications will not be covered.

This product is made with the highest quality materials and is warranted to be free from defects

in materials and workmanship at the time of purchase. This limited warranty applies to products

manufactured or distributed by the manufacturer, are delivered in the continental United States or

Canada and extends to the original purchaser, or gift recipient. This warranty becomes valid at the

time of purchase and terminates either by the speciﬁed time frame listed above and/or owner transfer.

Any refunds or monetary compensations must be claimed through the place of purchase (retailer), and

not through the manufacturer. Any extended warranties (warranties that cover above and beyond this

manufacturer warranty) that are sold through a retailer or third party, are not directly correlated with

this products’ limited warranty, and may be redirected to said retailer or third party for coverage.

This warranty extends through the manufacturer of the product, and covers functional parts only.

Cosmetics are not covered, unless unequivocally determined it is a workmanship defect. Shipping

damage should be addressed with the shipping company, retailer, or place of purchase, not the

manufacturer unless the manufacturer was the direct shipper.

The manufacturer’s sole obligation under this warranty shall be limited to furnishing the original

purchaser replacement parts for units deemed repairable by the supplier’s warranty department.

The purchaser is responsible for insuring any parts shipped or returned, if desired. The purchaser is

responsible to prepay any shipping charges (both ways) including, but not limited to taxes and duties. All

exchanged parts and products replaced under this warranty will become the property of manufacturer.

The manufacturer reserves the right to change manufacturers of replacement parts or products for

use, in order to cover any existing warranty.

The purchaser may be asked to provide the supplier with proof of purchase documents (including the

date of purchase) if requested. Any evidence of alteration, erasing, or forgery of proof of purchase

documents will be just cause to VOID this limited warranty. Products, in which the serial number has

been defaced or removed are not eligible for warranty coverage.

This warranty does not apply if the unit has been subject to negligence, fabrication, misuse, abuse, or

repairs, alteration by non-manufacturer authorized personnel, inappropriate installations, or any case

beyond the control of the manufacturer. Examples of warranty invalidation may also include, but are

not limited to:

• Use of lacquer or paints in (and around) the heaters

• Heater placed on non-approved surfaces

• Electrical requirement deﬁciencies (15-20 amp dedicated outlet)

• Use on extension cords/timers/surge protectors/GFCI

• Outdoor applications

• Normal wear/tear/weathering

• Pet/consumer accidents

The manufacturer shall not be liable for any loss due to use (or misuse) of the heater or other incidental

or consequential costs, expense or damages without irrefutable foundations. Under no circumstances

shall the manufacturer or any of its representatives be held liable for injury to any person or damage

to any property, however arising. Any implied warranty shall have duration equal of the applicable

warranty stated above. Speciﬁcations are subject to change without notice or obligation.

This limited warranty gives the original purchaser speciﬁc legal rights. Other rights may vary from state

to state.

REPLACEMENT PARTS LIST

For replacement parts, call our technical support department at 657-341-0362,, 9 a.m. - 5 p.m., PST,

Monday - Friday

PART DESCRIPTION PART #

A Control panel COPA-F2016

B Fan FAN6048

C Power board POBO-F2016

D Tip-over switch TIPSW

E Spindle Motor SMOTOR

F Manual Thermostat LIMITSW130

G Infrared tube QUAR-R3

H Thermostat Wire SENSOR

I Remote control REMO-F2016

H I

Printed in China

lifesmart

is a registered trademark

PLEASE REMEMBER TO REGISTER YOUR WARRANTY:

web: www.lifesmartcomfort.com

email: cs@scsources.com

Lifesmart FP1136 Mode d'emploi

Marque: Lifesmart

Modèle: FP1136

Catégorie: Cheminées

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Lifesmart FP1136 Operating instructions

Lifesmart FP1136 Mode d'emploi

Lifesmart FP1136 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents