Skil SD561802 Le manuel du propriétaire

Marque: Skil

Modèle: SD561802

Catégorie: Outils électroportatifs

Taper: Le manuel du propriétaire

Owner’s Manual

Guide d’utilisation

Manual del propietario

WARNING: To reduce the risk of injury, the user must read and understand the

Owner’s Manual before using this product. Save these instructions for future reference.

AVERTISSEMENT : Afin de réduire les risques de blessure, l’utilisateur doit lire et

comprendre le guide d’utilisation avant d’utiliser cet article. Conservez le présent guide

afin de pouvoir le consulter ultérieurement.

ADVERTENCIA : Para reducir el riesgo de lesiones, el usuario debe leer y comprender

el Manual del operador antes de utilizar este producto. Guarde estas instrucciones para

consultarlas en caso sea necesario.

For Customer Service

Pour le service à la clientèle

Servicio al cliente

Rechargeable Screwdriver with Pivot Grip

Tournevis rechargeable à poignée pivotante

1-877-SKIL-999

www.skil.com

Model/ Modelo/ Modèle: SD561802

TABLE OF CONTENTS

General Power Tool Safety Warnings .............................3-5

Safety Warnings for Screwdriver ...................................5

Other Safety Instructions .......................................5-6

FCC Caution ....................................................6

Symbols ....................................................7-10

Get to Know Your Screwdriver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Specications .................................................11

Operating Instructions .......................................12-15

Maintenance ...................................................16

Troubleshooting ...............................................17

Limited Warranty of SKIL Cordless Tool ............................18

WARNING

•

Some dust created by power sanding, sawing, grinding, drilling and other construction

activities contains chemicals known to the State of California to cause cancer, birth defects

or other reproductive harm. Some examples of these chemicals are:

–

Lead from lead-based paints.

–

Crystalline silica from bricks, cement, and other masonry products.

–

Arsenic and chromium from chemically-treated lumber.

•

Your risk from these exposures varies, depending upon how often you do this type of work.

To reduce your exposure to these chemicals:

–

Work in a well-ventilated area.

–

Work with approved safety equipment, such as dust masks that are specially designed to

lter out microscopic particles.

–

Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and

other construction activities. Wear protective clothing and wash exposed areas with soap

and water. Allowing dust to get into your mouth or eyes or to lie on the skin may promote

absorption of harmful chemicals.

GENERAL POWER TOOL SAFETY WARNINGS

WARNING

Read all safety warnings, instructions, illustrations and specications

provided with this power tool. Failure to follow all instructions listed

below may result in electric shock, re and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE

REFERENCE.

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

Work area safety

Keep work area clean and well lit. Cluttered or dark areas invite accidents.

Do not operate power tools in explosive atmospheres, such as in the presence of

ammable liquids, gases or dust. Power tools create sparks which may ignite the dust or

fumes.

Keep children and bystanders away while operating a power tool. Distractions can cause

you to lose control.

Electrical safety

Power tool plugs must match the outlet. Never modify the plug in any way. Do not use

any adapter plugs with earthed (grounded) power tools. Unmodied plugs and matching

outlets will reduce risk of electric shock.

Avoid body contact with earthed or grounded surfaces, such as pipes, radiators,

ranges and refrigerators. There is an increased risk of electric shock if your body is earthed

or grounded.

Do not expose power tools to rain or wet conditions. Water entering a power tool will

increase the risk of electric shock.

Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power

tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled

cords increase the risk of electric shock.

When operating a power tool outdoors, use an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces the risk of electric shock.

If operating a power tool in a damp location is unavoidable, use a ground fault circuit

interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of electric shock.

Personal safety

Stay alert, watch what you are doing and use common sense when operating a power

tool. Do not use a power tool while you are tired or under the inuence of drugs,

alcohol or medication. A moment of inattention while operating power tools may result in

serious personal injury.

Use personal protective equipment. Always wear eye protection. Protective equipment

such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for

appropriate conditions will reduce personal injuries.

Prevent unintentional starting. Ensure the switch is in the off-position before

connecting to power source and/or battery pack, picking up or carrying the tool.

Carrying power tools with your nger on the switch or energising power tools that have the

switch on invites accidents.

Remove any adjusting key or wrench before turning the power tool on. A wrench or a

key left attached to a rotating part of the power tool may result in personal injury.

Do not overreach. Keep proper footing and balance at all times. This enables better

control of the power tool in unexpected situations.

Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and

gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in

moving parts.

If devices are provided for the connection of dust extraction and collection facilities,

ensure these are connected and properly used. Use of dust collection can reduce dust-

related hazards.

Do not let familiarity gained from frequent use of tools allow you to become complacent

and ignore tool safety principles. A careless action can cause severe injury within a fraction

of a second.

Power tool use and care

Do not force the power tool. Use the correct power tool for your application. The correct

power tool will do the job better and safer at the rate for which it was designed.

Do not use the power tool if the switch does not turn it on and off. Any power tool that

cannot be controlled with the switch is dangerous and must be repaired.

Disconnect the plug from the power source and/or remove the battery pack, if

detachable, from the power tool before making any adjustments, changing accessories,

or storing power tools. Such preventive safety measures reduce the risk of starting the

power tool accidentally.

Store idle power tools out of the reach of children and do not allow persons unfamiliar

with the power tool or these instructions to operate the power tool. Power tools are

dangerous in the hands of untrained users.

Maintain power tools and accessories. Check for misalignment or binding of moving

parts, breakage of parts and any other condition that may affect the power tool’s

operation. If damaged, have the power tool repaired before use. Many accidents are

caused by poorly maintained power tools.

Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to control.

Use the power tool, accessories and tool bits etc. in accordance with these instructions,

taking into account the working conditions and the work to be performed. Use of the

power tool for operations different from those intended could result in a hazardous situation.

Keep handles and grasping surfaces dry, clean and free from oil and grease.

Slippery handles and grasping surfaces do not allow for safe handling and control of the tool

in unexpected situations.

Battery tool use and care

Recharge only with the charger specied by the manufacturer. A charger that is suitable

for one type of battery pack may create a risk of re when used with another battery pack.

Use power tools only with specically designated battery packs. Use of any other battery

packs may create a risk of injury and re.

When battery pack is not in use, keep it away from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal objects, that can make a connection

from one terminal to another. Shorting the battery terminals together may cause burns or a

re.

Under abusive conditions, liquid may be ejected from the battery; avoid contact. If

contact accidentally occurs, ush with water. If liquid contacts eyes, additionally seek

medical help. Liquid ejected from the battery may cause irritation or burns.

Do not use a battery pack or tool that is damaged or modied. Damaged or modied

batteries may exhibit unpredictable behaviour resulting in re, explosion or risk of injury.

Do not expose a battery pack or tool to re or excessive temperature. Exposure to re or

temperature above 265 °F may cause explosion.

Follow all charging instructions and do not charge the battery pack or tool outside the

temperature range specied in the instructions. Charging improperly or at temperatures

outside the specied range may damage the battery and increase the risk of re.

Service

Have your power tool serviced by a qualied repair person using only identical

replacement parts. This will ensure that the safety of the power tool is maintained.

Never service damaged battery packs. Service of battery packs should only be performed

by the manufacturer or authorized service providers.

SAFETY WARNINGS FOR SCREWDRIVER

Hold the power tool by insulated gripping surfaces, when performing an operation

where the fastener may contact hidden wiring. Fasteners contacting a “live” wire may

make exposed metal parts of the power tool “live” and could give the operator an electric

shock.

OTHER SAFETY INSTRUCTIONS

DANGER

To reduce the risk of re or electric shock, carefully follow these

instructions.

Before using power supply, read all instructions and cautionary markings on (1) power

supply, (2) battery pack, and (3) product using battery.

Charge battery pack and/or product within the required temperature range. Store power

supply and battery pack in locations where temperature is within the recommended

storage temperature range. This is important to prevent serious damage to the battery cells.

Do not recharge battery in damp or wet environment. Do not expose power supply to

rain or snow. Water entering power supply may result in electric shock or re.

Battery leakage may occur under extreme usage or temperature conditions. Avoid

contact with skin and eyes. The battery liquid is caustic and could cause chemical burns

to tissues. If liquid comes in contact with skin, wash quickly with soap and water. If the liquid

contacts your eyes, ush them with water for a minimum of 10 minutes and seek medical

attention.

Place power supply on at nonammable surfaces and away from ammable materials

when recharging battery pack. Carpeting and other heat insulating surfaces block proper

air circulation which may cause overheating of the power supply and battery pack. If smoke or

melting of the power supply or battery pack is observed, unplug the power supply immediately

and do not use the battery pack or power supply. Contact customer service immediately.

Keep the cord and power supply from heat to prevent damage to housing or internal

parts.

Do not allow gasoline, oils, petroleum-based products, etc. to come in contact with

plastic parts. These materials contain chemicals that can damage, weaken, or destroy

plastic.

Make sure cord is located so that it will not be stepped on, tripped over, or otherwise

subjected to damage or stress. Damaged plug and cord may result in electric shock or re.

Disconnect the power supply by pulling the plug rather than the cord. Do not operate

power supply with damaged cord or plug; have them replaced immediately. Damaged

plug or cord may result in electric shock or re.

Do not insert battery pack in power supply if battery pack case is cracked. Using

damaged battery pack may result in electric shock or re.

Before each use, check the power supply, cable and plug. If damage is detected, do not

use the power supply. Never open the power supply yourself, take it to a Skil Factory

Service Center, or qualied serviceman only using original spare parts. Incorrect

reassembly may result in electric shock or re.

Unplug power supply from outlet before storage, attempting any maintenance or

cleaning. Such preventive safety measures reduce the risk of electric shock or re.

Replace battery pack if a substantial drop in operating time per charge is observed.

Battery pack may be nearing the end of its life.

To reduce the risk of injury, close supervision is necessary when an appliance is used

near children.

Do not use outdoors.

IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS

FCC CAUTION

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including interference that may cause

undesired operation.

2. Changes or modications not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

•

Consult the dealer or an experienced radio/TV technician for help.

DANGER

People with electronic devices, such as pacemakers, should consult their

physician(s) before using this product. Operation of electrical equipment in

close proximity to a heart pacemaker could cause interference or failure of the pacemaker.

SYMBOLS

Safety Symbols

The purpose of safety symbols is to attract your attention to possible dangers. The safety

symbols and the explanations with them deserve your careful attention and understanding.

The symbol warnings do not, by themselves, eliminate any danger. The instructions and

warnings they give are no substitutes for proper accident prevention measures.

WARNING

Be sure to read and understand all safety instructions in this Owner's

Manual, including all safety alert symbols such as “DANGER,”

“WARNING,” and “CAUTION” before using this tool. Failure to following all instructions listed

below may result in electric shock, re, and/or serious personal injury.

The denitions below describe the level of severity for each signal word. Please read the manual

and pay attention to these symbols.

This is the safety alert symbol. It is used to alert you to potential

personal injury hazards. Obey all safety messages that follow this

symbol to avoid possible injury or death.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION

CAUTION, used with the safety alert symbol, indicates a hazardous

situation which, if not avoided, will result in minor or moderate injury.

Damage Prevention and Information Messages

These inform the user of important information and/or instructions that could lead to equipment

or other property damage if they are not followed. Each message is preceded by the word

“NOTICE”, as in the example below:

NOTICE: Equipment and/or property damage may result if these instructions are not followed.

WARNING

The operation of any power tools can result in

foreign

objects being thrown into your eyes, which can result

in severe eye damage. Before beginning power tool operation, always

wear safety goggles or safety glasses with side shields and a full face

shield when needed. We recommend a Wide Vision Safety Mask for use

over eyeglasses or standard safety glasses with side shields. Always use

eye protection which is marked to comply with ANSI Z87.1.

SYMBOLS (CONTINUED)

IMPORTANT: Some of the following symbols may be used on your tool. Please study them

and learn their meaning. Proper interpretation of these symbols will allow you to operate the

tool better and more safely.

Symbol Name Designation/Explanation

V Volts Voltage (potential)

A Amperes Current

Hz Hertz Frequency (cycles per second)

W Watt Power

kg Kilograms Weight

min Minutes Time

s Seconds Time

Wh Watt-hours Battery capacity

Ah Ampere-Hours Battery capacity

Ø Diameter Size of drill bits, grinding wheels, etc.

No load speed Rotational speed, at no load

n Rated speed Maximum attainable speed

…/min

Revolutions or reciprocation

per minute

Revolutions, strokes, surface speed,

orbits, etc. per minute

0 Off position Zero speed, zero torque...

1,2,3,…

I,II,III,

Selector settings

Speed, torque or position settings. Higher

number means greater speed

Innitely variable selector

with off

Speed is increasing from 0 setting

Arrow Action in the direction of arrow

Alternating current Type or a characteristic of current

Direct current Type or a characteristic of current

Alternating or direct current Type or a characteristic of current

Class II construction

Designates Double Insulated Construction

tools.

Earthing terminal Grounding terminal

Li-ion RBRC seal

Designates Li-ion battery recycling

program

Symbol Name Designation/Explanation

Ni-Cad RBRC seal

Designates Ni-Cad battery recycling

program

Read manual symbol Alerts user to read manual

Wear eye protection symbol

Always wear safety goggles or safety

glasses with side shields and a full face

shield when operating this product.

SYMBOLS (CERTIFICATION INFORMATION)

IMPORTANT: Some of the following symbols for certication information may be used on your

tool. Please study them and learn their meaning. Proper interpretation of these symbols will

allow you to operate the tool better and more safely.

This symbol designates that this tool is listed by Underwriters Laboratories.

This symbol designates that this tool is recognized by Underwriters

Laboratories.

This symbol designates that this tool is listed by Underwriters

Laboratories, to United States and Canadian Standards.

This symbol designates that this tool is listed by the Canadian

Standards Association.

This symbol designates that this tool is listed by the Canadian

Standards Association, to United States and Canadian Standards.

This symbol designates that this tool is listed by the Intertek Testing

Services, to United States and Canadian Standards.

This symbol designates that this tool complies to NOM Mexican

Standards.

This symbol designates that this tool is listed by the California Energy

Commission.

GET TO KNOW YOUR SCREWDRIVER

4V Rechargeable Screwdriver with Pivot Grip

Fig. 1

Pivot-Unlock Knob

Direction-of-

Rotation (forward/

center-lock/

reverse) Selector

Handle

Charging Port

Charging Indicator

USB Charging Cable

Power Supply

(included with some

models)

Magnetic Bit Storage (X2)

LED Worklight

Magnetic Bit Holder

Trigger Switch

SPECIFICATIONS

Battery voltage 4V d.c. Lithium

Battery capacity 1.5Ah (6Wh)

Collet size 1/4” (Hex)

Recommended working temperature 50~95

F (10~35

Recommended charging temperature 41~104

F (5~40

Recommended storage temperature 32~104

F (0~40

OPERATING INSTRUCTIONS

WARNING

To reduce the risk of re, personal injury, and product damage due to

a short circuit, never immerse your tool, battery pack or power supply

in uid or allow a uid to allow inside them. Corrosive or conductive uids, such as

seawater, certain industrial chemicals, bleach or bleach-containing products, etc., can cause a

short circuit.

WARNING

If any parts are damaged or missing, do not operate this product until

the parts are replaced. Use of this product with damaged or missing parts

could result in serious personal injury.

To Charge the Battery (Fig. 2)

NOTICE: Charge before rst use. The screwdriver is shipped partially charged; fully charge

the battery before rst use.

Optimum performance can be reached by recharging the tool for about 3 hours. It is not

recommended that the tool be recharged for more than 24 hours.

For use only with SKIL SC536301 (Output: 5V 1A) power supply or Listed/Certied Information

Technology (Computer Equipment).

WARNING

Never charge the tool with any power supply or power source that is

not listed/certied. Failure to obey this warning could cause battery

damage and serious personal injury.

a) Insert the USB interface of the USB charging cable into the power supply.

b) Insert the charging plug into the charging port, making sure that they are properly

connected.

c) Connect the power supply (together with USB charging cable) to a power outlet. The

charging indicator light on the screwdriver will ash green to indicate that the tool is

charging.

d) When charging is complete, the charging indicator light will remain green, without ashing.

Remove the USB charging cable from the tool.

NOTICE: The tool will not operate when the trigger switch is depressed during charging.

NOTICE: The bottom of the tool may become warm during charging. This is normal.

NOTICE: Do not charge the tool in extremely hot or cold conditions. Charging is best achieved

at normal room temperature.

Fig. 2

(included with

some models)

Direction-of-Rotation (Forward/Center-Lock/Reverse) Selector

WARNING

After tool use, lock the direction-of-rotation selector in the “OFF”

position (center-lock) to help prevent accidental starting.

Your tool is equipped with a direction-of-rotation selector. This selector is designed to change

the direction of rotation of the bit and to lock the trigger in the “OFF” (center-lock) position.

a) Position the direction-of-rotation selector to the right for forward rotation.

b) Position the direction-of-rotation selector to the left for reverse rotation.

c) Position the selector in the “OFF” (center-lock) position to help to reduce the possibility of

accidental starting when the tool is not in use (Fig. 3).

NOTICE:

To prevent gear damage, always allow the screwdriver to come to a complete stop

before changing the direction of rotation.

NOTICE:

The screwdriver will not operate unless the direction-of-rotation selector is fully

engaged to indicate either forward or reverse.

Fig. 3

Forward Center-Lock Reverse

Trigger Switch

Your tool is equipped with a trigger switch with room for two ngers for more comfortable

operation and better control.

The tool can be turned “ON” by depressing the trigger switch, or “OFF” by releasing the trigger

switch (Fig. 4).

Fig. 4

LED Worklight (Fig. 5)

Your tool is equipped with an LED worklight,

which illuminates when the trigger is squeezed.

This provides additional light on the surface

of the work piece for operation in lower-light

areas.

The LED worklight will automatically turn on

when the trigger switch is depressed, and turn

off after the trigger switch is released.

Two Handle Positions (Fig. 6)

Your tool features two handle positions for

convenience in various operations.

a. Depress the pivot-unlock knob and twist the

handle to alternate between the two handle

positions.

b. Release the pivot-unlock knob and check to

make sure that the handle is locked in place.

NOTICE: Do not over-twist the handle.

Install and Remove Bits

Your tool is equipped with a magnetic bit

holder, making bit installation and removal very

convenient (Fig. 6).

Lock the trigger switch “OFF” by placing the

direction-of-rotation selector in the center

position.

a) To install the bit:

Insert the bit into the holder. The integrated

magnet will help to securely hold the bit in

place.

b) To remove the bit:

Just pull the bit out of the holder.

WARNING

Use protective gloves

when removing the bit

from the tool, or rst allow the bit to cool down. The bit may be hot after prolonged use.

Fig. 5

Fig. 6

Fig. 7

Screw Driving

a) Install a suitable bit.

NOTICE: Always use the correct type and size

of screwdriver bit for your application.

b) To tighten a screw, set the direction of

rotation at “Forward”.

c) To loosen a screw, set the direction of

rotation at “Reverse”.

d) Grasping only the handle of the tool, align

the bit perpendicular to the screw (Fig.8).

e) Apply just enough pressure to keep the

bit engaged on the screw and depress the

trigger switch to begin screw driving.

NOTICE: The screwdriver may also be used

manually as a non-powered screwdriver without battery power.

NOTICE: Do not over-tighten, as the force of the screwdriver can break the fastener. Keep the

screwdriver at a right angle to the fastener to avoid damaging the fastener head.

Fig. 8

MAINTENANCE

WARNING

Before performing maintenance or cleaning, always lock the

direction-of-rotation selector in the “OFF” position (center-lock) to

help prevent accidental starting.

Service

WARNING

Preventive maintenance performed by unauthorized personnel may

result in misplacing of internal wires and components which could

cause serious hazard. We recommend that all tool service be performed by a SKIL Factory

Service Center or Authorized SKIL Service Station.

General Maintenance

WARNING

When servicing, use only identical replacement parts. Use of any

other parts could create a hazard or cause product damage.

Periodically inspect the entire product for damaged, missing, or loose parts such as screws,

nuts, bolts, caps, etc. Tighten securely all fasteners and caps and do not operate this product

until all missing or damaged parts are replaced. Please contact customer service or an

authorized service center for assistance.

Cleaning

WARNING

The tool may be cleaned most effectively with compressed dry air.

Always wear safety goggles when cleaning tools with compressed

air. Ventilation openings and switch levers must be kept clean and free of foreign matter. Do

not attempt to clean by inserting pointed objects through openings.

WARNING

Certain cleaning agents and solvents damage plastic parts. Some of

these are: gasoline, carbon tetrachloride, chlorinated cleaning solvents,

ammonia and household detergents that contain ammonia.

Storage

Store the tool indoors in a place that is inaccessible to children. Keep it away from corrosive

agents.

TROUBLESHOOTING

Problem Cause Remedy

Tool does not work. 1. Battery is depleted.

2. Tool is over-loaded.

3. Battery is over-temperature.

4. Burned out switch.

1. Charge the battery.

2. Release the trigger switch

and try again.

3. Turn off the tool and allow

the tool to cool.

4. Have the switch replaced

by an Authorized SKIL

Service Center or Service

Station.

Bit cannot be installed. 1. Something is stuck in the

bit holder.

2. Bit does not t the holder.

1. Clean the bit holder.

2. Use suitable bit or adapter.

FOR RECYCLING

To preserve natural resources, please recycle or dispose of batteries

properly. This product contains lithium-ion batteries. Local, state, or federal

laws may prohibit disposal of lithium-ion batteries in ordinary trash. Consult

your local waste authority for information regarding available recycling and/

or disposal options.

LIMITED WARRANTY OF SKIL CONSUMER TOOLS

5 YEAR LIMITED WARRANTY- LEGAL

Chervon North America, Inc. ("Seller") warrants to the original purchaser only, that all SKIL

consumer TOOLS will be free from defects in material or workmanship for a period of ve

years from date of purchase, if original purchaser registers the product within 30 days from

purchase. BATTERIES AND CHARGERS are warranted for 2 years. Product registration

can be completed online at www.Registermyskil.com. Original purchasers should also retain

their receipt as proof of purchase. THE FIVE-YEAR WARRANTY PERIOD FOR TOOLS IS

CONDITIONED ON REGISTRATION OF THE PRODUCT WITHIN 30 DAYS OF PURCHASE.

If original purchasers do not register their product timely, the foregoing limited warranty will

apply for a duration of three years for tools. All batteries and chargers will remain under the

two-year limited warranty.

Notwithstanding the foregoing, if a SKIL consumer tool is used for industrial, professional

or commercial purposes, the foregoing warranty will apply for a duration of ninety days,

regardless of registration.

SELLER’S SOLE OBLIGATION AND YOUR EXCLUSIVE REMEDY under this Limited

Warranty and, to the extent permitted by law, any warranty or condition implied by law, shall

be the repair or replacement of parts, without charge, which are defective in material or

workmanship and which have not been misused, carelessly handled, or repaired by persons

other than Seller or Authorized Service Station. To make a claim under this Limited Warranty,

you must return the complete product, transportation prepaid, to any SKIL Factory Service

Center or Authorized Service Station. For Authorized SKIL Power Tool Service Stations,

please visit www.Registermyskil.com or call 1-877-SKIL-999 (1-877-754-5999).

THIS LIMITED WARRANTY DOES NOT APPLY TO ACCESSORY ITEMS SUCH AS

CIRCULAR SAW BLADES, DRILL BITS, ROUTER BITS, JIGSAW BLADES, SANDING

BELTS, GRINDING WHEELS AND OTHER RELATED ITEMS.

ANY IMPLIED WARRANTIES APPLICABLE TO A PRODUCT SHALL BE LIMITED IN

DURATION EQUAL TO THE DURATION OF THE EXPRESS WARRANTIES APPLICABLE

TO SUCH PRODUCT, AS SET FORTH IN THE FIRST PARAGRAPH ABOVE. SOME

STATES IN THE U.S., SOME CANADIAN PROVINCES DO NOT ALLOW LIMITATIONS ON

HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT

APPLY TO YOU.

IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL

DAMAGES (INCLUDING BUT NOT LIMITED TO LIABILITY FOR LOSS OF PROFITS)

ARISING FROM THE SALE OR USE OF THIS PRODUCT. SOME STATES IN THE U.S.

AND SOME CANADIAN PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION

OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR

EXCLUSION MAY NOT APPLY TO YOU.

THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO

HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE IN THE U.S., PROVINCE

TO PROVINCE IN CANADA AND FROM COUNTRY TO COUNTRY.

THIS LIMITED WARRANTY APPLIES ONLY TO PRODUCTS SOLD WITHIN THE UNITED

STATES OF AMERICA, CANADA AND THE COMMONWEALTH OF PUERTO RICO. FOR

WARRANTY COVERAGE WITHIN OTHER COUNTRIES, CONTACT YOUR LOCAL SKIL

DEALER OR IMPORTER.

08/18

TABLE DES MATIÈRES

Avertissements de sécurité généraux relatifs aux outils électriques . 20-22

Avertissements de sécurité relatifs au tournevis. . . . . . . . . . . . . . . . . . . . .22

Autres consignes de sécurité .................................23-24

Mise en garde de la FCC .........................................24

Symboles ..................................................25-28

Apprenez à connaître votre luminaire ..............................29

Caractéristiques techniques .....................................29

Mode d’emploi ..............................................30-33

Entretien ......................................................34

Dépannage ....................................................35

Garantie limitée de l’outil sans l SKIL ..........................36-37

AVERTISSEMENT

•

La poussière créée pendant le ponçage, le sciage, le polissage, le perçage et d’autres

activités liées à la construction peut contenir des produits chimiques reconnus par l’État

de la Californie comme étant la cause de cancers, d’anomalies congénitales et d’autres

problèmes liés aux fonctions reproductrices. Voici des exemples de ces produits chimiques :

–

Plomb provenant de peintures à base de plomb.

–

Silice cristalline provenant de la brique, du ciment ou d’autres matériaux de maçonnerie.

–

Arsenic et chrome contenus dans le bois d’œuvre traité avec des produits chimiques.

•

Les risques liés à l’exposition à ces produits varient selon le nombre de fois où vous

pratiquez ces activités. Pour réduire votre exposition à ces produits chimiques :

–

Travaillez dans un endroit bien ventilé.

–

Munissez-vous de l’équipement de sécurité approuvé tel que des masques antipoussières

conçus spécialement pour ltrer les particules microscopiques.

–

Évitez l’exposition prolongée à la poussière causée par le ponçage mécanique, le sciage, le

polissage, le perçage et d’autres activités liées à la construction. Portez un équipement de

protection et lavez à l’eau et au savon toutes les parties exposées. Les poussières pénétrant

dans votre bouche ou dans vos yeux et les poussières se déposant sur votre peau peuvent

causer l’absorption de produits chimiques dangereux.

AVERTISSEMENTS DE SÉCURITÉ GÉNÉRAUX RELATIFS

AUX OUTILS ÉLECTRIQUES

AVERTISSEMENT

Lisez tous les avertissements et toutes les instructions,

illustrations et spécications fournis avec cet outil

électrique. Le non-respect des consignes de sécurité ci-dessous peut occasionner un choc

électrique, un incendie ou des blessures graves.

CONSERVEZ TOUS LES AVERTISSEMENTS ET TOUTES LES

INSTRUCTIONS AFIN DE POUVOIR LES CONSULTER RÉFÉRER

ULTÉRIEUREMENT.

L’expression « outil électrique » utilisée dans les avertissements correspond aux outils

électriques alimentés sur secteur (à l) ou alimentés par piles (sans l).

Mesures de sécurité dans l’aire de travail

Maintenez l’aire de travail propre et bien éclairée. Les aires de travail sombres et

encombrées sont propices aux accidents.

N’utilisez pas d’outils électriques dans un endroit présentant un risque d’explosion,

par exemple en présence de liquides, de gaz ou de poussières inammables. Les outils

électriques produisent des étincelles pouvant causer un incendie en raison de la poussière et

des fumées.

Gardez les enfants et les autres personnes à l’écart lorsque vous utilisez un outil

électrique. Une distraction peut vous faire perdre la maîtrise de l’outil.

Consignes de sécurité relatives à l’électricité

Les ches des outils électriques doivent correspondre à la prise. Ne modiez jamais la

che de quelque façon que ce soit. N’utilisez pas d’adaptateur avec les outils électriques

mis à la terre. L’utilisation de ches non modiées dans les prises compatibles réduit les

risques de choc électrique.

Évitez de toucher à des surfaces mises à la terre, par exemple, un tuyau, un radiateur,

une cuisinière ou un réfrigérateur. Le contact du corps avec une surface mise à la terre

augmente les risques de choc électrique.

N’exposez pas les outils électriques à la pluie ni à tout environnement humide.

L’inltration d’eau dans un outil électrique augmente les risques de décharge électrique.

N’utilisez pas le cordon d’alimentation de façon à l’endommager. Ne transportez jamais

un outil électrique en le tenant par son cordon, et ne tirez jamais sur le cordon pour le

débrancher. Tenez le cordon d’alimentation éloigné des sources de chaleur, de l’huile,

des objets coupants et des pièces mobiles. Les risques de choc électrique sont plus

élevés si le cordon d’alimentation est endommagé ou emmêlé.

Lorsque vous utilisez un outil électrique à l’extérieur, utilisez une rallonge conçue pour

être utilisée à l’extérieur. Ce type de rallonge réduit les risques de choc électrique.

Si vous n’avez d’autre choix que d’utiliser un outil électrique dans un endroit humide,

utilisez une alimentation protégée par un disjoncteur différentiel. L’utilisation d’un

disjoncteur différentiel réduit les risques de choc électrique.

Sécurité personnelle

Soyez vigilant, prêtez attention à ce que vous faites et usez de votre jugement lorsque

vous utilisez un outil électrique. N’utilisez pas un outil électrique lorsque vous êtes

fatigué ou sous l’effet de drogues, d’alcool ou de médicaments. Un moment d’inattention

lorsque vous utilisez des outils électriques peut occasionner des blessures graves.

La page est en cours de chargement...

Skil SD561802 Le manuel du propriétaire

Marque: Skil

Modèle: SD561802

Catégorie: Outils électroportatifs

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Skil SD561802 Owner's manual

Skil SD561802 Le manuel du propriétaire

Skil SD561802 Le manuel du propriétaire

dans d''autres langues

Documents connexes