URBANGLIDE URBBK12928 Manuel utilisateur

1

MANUEL D’UTILISATION

MANUAL

URBANGLIDE is a brand imported by the PACT GROUP,

Located at 33 rue du Ballon - 93160 Noisy Le Grand - France

USER MANUAL

BIKE M7

PO3068

2

3

Safety and precaution

Please read the manual carefully before using the product and read the risks and safety tips in the manual. The

use of an electrical product can be dangerous if the user is not watchful. Misuse and non-respect with the safety

instructions does not affect the company in event of accident. Self-judgment and common sense are necessary

for users to detect the possible dangers.

Please verify the current regulations and laws in your country to know where and how to use your product legally.

You must comply with the rules and laws that applicable to vehicles and pedestrians.

• Protective equipment

Always wear the following protective equipment:

- Approved and certified helmet according to your location

- Knee pads and elbow patches

- Long sleeve t-shirt and long pants

- Gloves

- Shoes with rubber soles, never drive in barefoot or sandal. Verify to make the laces made and keep

them as far as possible from the wheels and the internal system.

• Driver’s advice

The user must not be more than 120 kg, the size and weight do not fully certify that the user will have full control

of the vehicle. It is your responsibility to make sure that all users are aware of the risks. The recommended age

for using this product is 14 years. It is your responsibility to put a younger child into consideration by taking into

account their skills, maturity and ability and following the rules. Do not touch the engine or the brakes of the

product immediately after use, these parts may be extremely hot.

• Procedures and driving conditions

Please verify the current laws and rules in your country before using the product. In France, the linear speed on

level ground and a person not exceeding the maximum permissible load is 25km/hour. Look around when using

the product and pay attention to all possible risks. It is important to respect the rights and properties of everyone.

For your safety do not start the accelerator if you are not on the product. This product is not designed to make

jumps, acrobatic tricks and skids.

Never drive on roads, near vehicles, stairs, hills, swimming pools or other streams. Please hold the handlebars

with both hands. Never go on the product with more than one person. Be sure to keep your fingers and other body

parts away from hot parts during use (Brake, motor, chain). Never use the product with a Mp3 player, or with your

smartphone at hand.

Never use the product to pull anything, as this may damage the components and wear out the battery. Never put

the product in contact with water, the electrical components can be damaged and create a dangerous situation.

Roll only on flat and solid surfaces. Avoid surfaces with gravel, holes, ice, which can lead to loss of control of the

product. Do not drive at night or in areas where visibility is reduced. Do not ride indoors where there are carpets

as they can interfere.

The A-weighted emission sound pressure level at the driver's cab shall not exceed 70dB(A). The total value of the

vibrations to which the hand-arm system is exposed does not exceed 2.5m/s², the maximum frequency-weighted

root mean square value of the acceleration to which the whole body is exposed does not exceed 0.5m/².

(Measurement accuracy is uncertain)

After each use, verify that each piece is in its proper place, and that it is not damaged. Before each use, verify the

following points:

- The brakes are in good condition

- All components are in good condition and in their places

- The parts with defects in the last use have been repaired or replaced according to the manufacturer's

conditions.

- The maximum tyre inflation pressure is 6.40 bar.

People who have medical follow-up or treatment such as: cardiac people, pregnant women, irresponsible people

with back or neck problems, should not use the product.

4

• Usage of the charger

Before using the product, it is necessary to charge it. A long charge may be necessary before the first use. Please

refer to the battery indicator, you can charge your battery at any time to ensure the constant power. It is not

necessary to wait until the battery is completely empty to charge it.

Please do not use the charger of other brand, these can damage the battery of your product. To ensure a normal

life cycle, it is important to charge your battery at least once every 3 months, even if you are not using the product.

Avoid shocks and contact with water, these are factors not covered by the warranty that may damage the battery.

The supplied charger is "smart", it will stop at 100% of the charge and not damage the battery.

The charger must be in perfect condition during each use, verify the wires, the condition of connection ends and

connectors. If the product does not charge, the charger may be defective, it needs to be replaced.

The charger must be used only by an adult, it is important to unplug it from both sides when not charging.

• Battery

Please do not store the battery in extreme temperatures. Store it below 30 ° C and above 0 ° C. If you do not use

your product for 60-90 days, the battery may get worse. This loss of autonomy is due to lack of use and is

therefore not covered by the warranty.

At the end of its cycle, the battery must be discarded separately from the undifferentiated generic waste. Discard

the batteries in the containers provided for this purpose. The recovery and recycling of batteries contributes to

protect the environment and material resources conservation. This product contains a Li-ion battery, the extinction

of a possible fire must be done with a powder extinguisher (Fire class D).

• Maintenance

Please store your product in a dry, dust-free place, and avoid leaving it in a humid area or under the sun for too

long. To clean your appliance, use a damp cloth and mild detergent. Do not use alcohol, gasoline, kerosene, or

other corrosive chemical solvents to clean your appliance, which will damage its appearance and structure.

Constantly verify the condition of components of your product, if any part is damaged, please replace it before

using the product. If a part is not working, falling, and injuring may occur.

• Transport

If you wish to transport your product by air or other means of transport as well as its battery, please contact the

local authorities and the carrier beforehand to obtain the possible prohibitions and limits of transport. Lithium

batteries are considered dangerous in many countries. Please make sure that the access and transport are

allowed before travelling. International law prohibits the transport of lithium batteries by air.

• Use of the product

To turn on your product, press the Power button on your handlebars. To move forward, press the accelerator also

located on your handlebars. Place both feet on the product and squeeze the accelerator trigger. To brake, use the

manual brakes located on the handlebars. You can also use the rear mudguard if your product is equipped with

one. Before each use, please check that the wheels are not jammed and that the brakes are working. In order to

carry out some basic adjustments, in particular the brake control play, please go to our tutorial videos available on

our YouTube channel: URBANGLIDE CHANNEL.

The use of this type of product over a long period of time can cause vibrations which can be unpleasant, take

regular breaks. To warn other users of your presence, use the horn on your handlebars, if your product is

equipped with one.

• Rebus

THIS PRODUCT CONTAINS LITHIUM BATTERIES THAT MUST BE SAFELY RECYCLED: The battery must be

removed before disposal. Before any work is carried out, remember to switch it off and unplug it from the socket.

5

• Listing of parts subject to wear:

Some parts require replacement depending on the degree of wear and tear and the time of use, you can obtain

spare parts at the following address (Section eBike M7)

https://boutique.urbanglide.com

Spare parts

Replacement

criteria

Acceptability

criteria

Replacement method

References

Tire

Loss of original

shape, cracks,

splinters or other

signs of wear and

tear

Online video on YouTube

Urbanglide Channel

On request to customer

service

Disc brake

Abnormal noise

when braking, low

thickness (<2.5mm)

Drive at 15Km/h

Brake on 1m, the

scooter must stop.

Online video on YouTube

Urbanglide Channel

On request to customer

service

Brake

Abnormal noises

when braking or

abnormal rubbing

noises

Online video on YouTube

Urbanglide Channel

Brake cable

Fraying cable

Online video on YouTube

Urbanglide Channel

On request to customer

service

Reflectives sticker

When it comes off

Online video on YouTube

Urbanglide Channel

On request to customer

service

Bearings

Abnormal noises

Contact our customer service

On request to customer

service

The serial number has the year of manufacture as a prefix on the information label of your product.

YYYYMMXXXXXXXXXXXX

Year

Month

6

Introduction

Before using your URBANGLIDE electric bicycle, it is important to read this user manual carefully. It is important to find

out about the regulations in place in your city, town, municipality, or country before using the product. Do not lend your

bike to anyone who is not familiar with this type of product.

Before using it for the first time, as well as for all other uses, check that all parts are properly assembled and in good

condition. If you have any questions, do not hesitate to contact us. You can also visit a specialist near you to analyse

and adjust your bike as best as possible. It is essential that the parts you assemble yourself: seal, handlebars, pedal,

are well assembled and checked regularly.

This bike is designed to be used on flat roads and slopes, but also on mixed surfaces such as mountain roads, forest

roads and gravel roads. However, it is not designed for jumping or tricks. Any user who does not respect these rules

will be held responsible in the event of an accident.

a) First use

- Check that the handlebars and stem are correctly tightened.

- Check that screws, bolts and other nuts are properly tightened.

- Check that the brakes are working properly.

- Check tyre pressure and condition

- Check the operation of the lights and reflectors

- Make sure the battery is fully charged

- Insert the battery into the bike, turn the key to turn on your battery.

- Start your bike by pressing the ignition button on the left handle for 2 seconds.

- Once the screen is switched on, it will display the battery status, assistance level, time, distance and speed.

- The engine starts when you start pedalling. Before starting to pedal, make sure that the assistance speed is at 0.

- To adjust the assistance level, press the "+" and "-" buttons on your display. The higher the level, the greater the

assistance.

b) Before each use

- Check the condition of your tyres

- Check your tyre pressure

- Check that no parts, bolts, screws, etc. are missing.

- Check that the brakes are working properly

- Check the functioning of the electronic parts

- Check that the lights are working and that the reflectors are in place.

- Check the condition and operation of the battery.

c) Recommended tightening

- Front axle nuts: 46N.m

- Rear axle nuts 70N.m

- Handlebar and stem clamping bolts 12N.m

- Handlebar stem expansion bolt 10N.m

- Seat column clamping nut 5-8N.m

- Saddle clamp nut 24N.m

- Gear lever nut 4N.m

- Rear support nut 8N.m

- Mudguard support nut 8N.m

7

Different parts

Editing

Before using your bike, there are a few simple assembly steps. Please follow these steps to assemble your bike.

STEP 1: UNPACKING

Remove all items from the carton and check that none of them are damaged. Remove all foam protection. Be careful

not to scratch or damage the product when cutting the clamps.

STEP 2: MOUNTING THE HANDLEBARS

Using the spanner supplied, unscrew the 4 screws at the point where the handlebars are to be inserted. (1)

Insert the handlebars in this position, use the marker to centre your handlebars and install them as best as possible.

(2)

1

2

8

Put the part you unscrewed previously on the handlebar (3), then screw it back in place using the 4 screws. When

tightening, make sure you are aligned with the mark on the handlebars.

STEP 3: ASSEMBLY OF THE SADDLE

Loosen the clamp by pulling the handle. (4) Then insert your saddle at the desired height. Please note that there is a

mark on the stem indicating the minimum height at which you should insert the saddle. (5) If you do not follow these

instructions, you may damage your bike and endanger yourself. Then tighten the clamp firmly and check that your

saddle is stable. Make sure that the saddle is properly aligned with the frame of your bicycle.

3

4

5

9

STEP 4: MOUNTING THE PEDALS

On each pedal is indicated the indication of its location. (6) "R" for right and "L" for left. Once the position has been

determined, start screwing the pedals onto the crankset. The direction in which the pedals are screwed on is also

indicated on the label. (6) Next, screw your pedals more firmly using the spanner provided. (7)

STEP 5: MOUNTING THE FRONT WHEEL

To mount the front wheel, use the black metal rod with the locking lever at the end. (8) Unscrew the round end of the

metal rod and also remove the spring.

Insert the metal rod in the centre of the wheel. (9) WARNING:

The locking lever must be opposite the brake pads on the wheel.

Once the rod is inserted in the centre of the wheel, replace the

spring and screw the round end back in place. Tighten the round

end securely and check that the spring is correctly seated.

7

6

8

9

10

Then take the front fork. Remove the cover in the centre of the fork.

(10)

IMPORTANT! The brake system is integrated in the fork. Before

starting the assembly, remove the protective tab located in the brake

system. (11)

Then insert the front fork into the front wheel. (12) CAUTION: Make sure that the brake pad on the wheel is inserted

into the brake system. The brake pad must be inserted where you removed the tongue. Place the two hooks of the fork

on either side of the metal rod.

10

11

12

11

Once the wheel is securely inserted into the fork, tighten the metal

rod using the locking lever on the fork. (13)

Once the assembly is finished, make sure that all parts are tight and

properly adjusted. Check that the brake system is correctly positioned

and that the brake pad is inserted.

Check that the handlebars are straight and tight.

Check that the saddle is aligned with the dial on the bike, and that it is

tight.

13

12

DISPLAY

The display gives you all the information about your bike. It shows the battery level, the gear

level, the speed you are at and the number of kilometres you have ridden.

To turn on your display, press the power button on the left side of your handlebars. To increase

the speed level press the top button. To decrease the speed level, press the bottom button.

Hold the top button to turn on the front light of your bike.

20

3

00001 km

Speed in Km/h

Battery level

Speed level

Distance travelled in Km

Increase the speed/light level

Reduce the speed level

Turning the display on/off

Km/h

13

USING THE SCREEN

Your screen has a multifunctional display.

ODO: Shows you the total number of kilometres you have cycled with your bike.

To reset this data, simply enter the menu of your bike. To do this, press the "+" and "-" buttons on your bike. Then

press the power button to move from setting to setting. Once you have reached the P16 setting, press and hold the

"-" button to reset your mileage counter to 0.

You can also record the distance travelled on two separate trips (e.g. out and back). To do this, press the power

button to switch from ODO to TRIP.

TRIP A: Record the distance travelled on the first trip.

TRIP B: Record the distance travelled on the second trip.

You can also get more information about your speed. Above the speed in km/h, there are different functions:

SPEED: Shows you the actual speed you are travelling at.

MAX: Shows you the maximum speed you have reached during your journey.

AVG : Shows you the average speed of your journey.

14

Charger

Connect your charger directly to your bike.

The charger displays two indicator lights : Charge and

Power

Power tells you that the charger is connected to a

power source and can therefore be used.

Charge tells you the charge level of your battery.

In charge

Charge

WARNING! Disconnect the charger when the battery is charged. This will avoid shortening the life of

the battery.

WARNING! Failure to use the battery for an extended period of time may cause irreparable damage

to the battery. Make sure to recharge the battery every 3 months for half an hour.

WARNING! If you do not use the bike for a long period of time, we recommend removing the

battery.

WARNING! When the battery is completely empty, you must recharge it immediately. Cells that

remain empty for a long time can suffer irreparable damage.

15

Use

1. The electronic gear change

To assist you electronically, your bike is equipped with 8 electronic speed levels.

- Position 0 = No assistance

- Position 1 and 2 = Economic position. Thanks to these positions, your bike consumes less energy. The

power is ideal for progressing on a flat surface. These two power levels will probably not be sufficient to tackle

a steep climb.

- Position 3 and 4 = Medium position

- Position 5 and 6 = High position. Your bike consumes more energy and is also more powerful.

- Position 7 and 8 = Maximum position. Your electrical assistance is at its maximum. These two speeds are

reserved for regular and speed-conscious users.

To scroll through the assistance level, press the "+" and "-" buttons on your bike's screen.

2. The operation of the electrical assistance

Your electric-assisted bicycle is equipped with an electric motor located in the rear wheel. This motor starts

automatically (if the ignition is switched on and the battery is charged) when you pedal and only when you pedal.

The motor switches off when :

- You apply one of the two brakes

- You reach the speed limit of 25km/hour.

This principle allows the engine to give you full power when you need it and saves battery power when you are

descending or launching on flat ground. This energy management allows you to acquire greater autonomy.

The range of your bike depends on several factors:

- The weight carried: The performance of your bike is given for an average load of 80kg.

- The outside temperature: The performance of your bike is given for an outside temperature of about 20°C.

- Battery wear and tear: Your battery is designed to deliver stable performance for 750 charge cycles, i.e. an

average use of 3 years.) After these 750 cycles, it is still operational, but its performance may decrease.

- The nature of the route: The range displayed is calculated on flat or slightly hilly ground (10 to 20% odds).

Autonomy varies according to the type of ground, the number of hills and descents on your course.

16

Troubleshooting

Problem

Possible cause

Solution

It does not work

The battery is not charged.

Charge the battery, check if the red

light is on.

Connections or cables are

disconnected.

Check that the battery is firmly seated

in the product

It does not work

continuously

The battery needs to be charged.

Charge the battery, check if the red

light is on.

The battery is not fully charged.

Make sure the power cable is well

connected.

The battery may need to be replaced.

It suddenly stopped

working

Overload, cut-off

Overloading may result in product

failure. Turn off the product, wait 15

seconds, then turn it on again.

Fuse burnt

Prior to this, check the condition of all

cables and connectors.

It is moving slowly

The brakes are not properly adjusted.

Check the condition of the brakes and

try to loosen. If this does not work,

please contact the after-sales service.

It has overloaded

Check that the user weighs less than

the previously recommended weight.

Check that there are no objects

obstructing the proper operation of the

product.

Bad driving condition.

Make sure you are on flat, dry, and

constant ground.

The tires / wheels are damaged.

Check the condition of the wheels of

the product.

17

For any information, contact our after-sales service at

the following address:

Support@urbanglide.com

You will also find many tutorial videos concerning the

maintenance and maintenance of your product on our

YouTube channel:

UrbanGlide Channel

Finally, do not hesitate to follow us on our social

networks Instagram and Facebook to follow our news.

You can find the latest update of this manual in digital

format by logging on to our website:

www.urbanglide.com

(Model section concerned).

The paper version will be given to you on request from

our customer service department.

All product names, logos and trademarks are the property of their respective owners. All company,

product and service names mentioned in this manual are for identification purposes only. Mention of

these names, logos and trademarks is not a recommendation for use.

18

DECLARATION OF CONFORMITY ORIGINAL

We undersigned PACT GROUP hereby declare that the product.

Model: URBANGLIDE EBIKE M7

Type: Electric bike

Function: Electric bike

Product description: Electrically assisted bicycle, with assisted pedaling, equipped with a 250W motor whose

power supply is gradually reduced and finally interrupted when the vehicle reaches a speed of 25 Km/h, or earlier,

if the cyclist stops pedaling.

Manufacturing batch: 062021URBBKM7BLMX0001 - 062021URBBKM7BLMX0430

Year of manufacture: 2021

Meets all standards and technical directives below:

. DIRECTIVES

2014/35/EU

TESTS STANDARD

EN 15194 :2017

All tests were carried out by the laboratories mentioned below:

TÜV Rheinland (Shanghai) Co., Ltd.

No 177,178, Lane 777 West Guangzhong Road,

Jing’an District, Shanghai, China

Mail: [email protected] Web: www.tuv.com

Shenzhen Anbotek Compliance Laboratory Limited

East of 4/F., Building A, Hourui No.3 Industrial Zone, Xixiang street Bao’an district.

Shenzhen, Guangdong, China

Contact details of the importer:

PACT GROUP

33 rue du ballon

93160 Noisy le Grand – France

Contact details of the person authorized to edit the technical document:

Fung NIM

33 rue du ballon

93160 Noisy le Grand - France

This declaration shall be issued under the responsibility of his representative.

26/07/2021

Representative of the company:

PACT GROUP

33 rue du ballon –

Noisy le Grand - France

Maurice Bodokh

CEO

1

BIKE M7

MANUEL D’UTILISATION

URBANGLIDE est une marque importée par la société PACT GROUP, localisée au

33 rue du Ballon - 93160 Noisy Le Grand - France

PO3068

La page charge ...

URBANGLIDE URBBK12928 Manuel utilisateur

URBANGLIDE URBBK12928 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents